LDC1101DRCR [TI]
用于高速应用的单通道、1.8V、24 位电感、16 位谐振器电阻、电感数字转换器 | DRC | 10 | -40 to 125;型号: | LDC1101DRCR |
厂家: | TEXAS INSTRUMENTS |
描述: | 用于高速应用的单通道、1.8V、24 位电感、16 位谐振器电阻、电感数字转换器 | DRC | 10 | -40 to 125 谐振器 转换器 |
文件: | 总55页 (文件大小:1578K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
LDC1101 1.8V 高分辨率、高速电感数字转换器
1 特性
3 说明
1
•
•
•
•
•
•
•
•
宽工作电压范围:1.8V 至 3.3V
LDC1101 是一款 1.8V 至 3.3V、高分辨率电感数字转
换器,可对位置、旋转或运动进行短距离、高速、无触
点感测,即使存在污垢或灰尘也能够实现可靠、精确的
测量,非常适合户外或严苛环境。
传感器频率范围:500kHz 至 10MHz
RP 分辨率:16 位
L 分辨率:16/24 位
180kSPS 转换速率
阈值检测功能
LDC1101 特有双感应测量内核,可在执行 > 150ksps
的 16 位 RP 和 L 测量的同时,进行分辨率高达 24 位
的高分辨率 L 测量,采样速率可高达 180ksps 以上。
LDC1101 包含阈值比较功能,该功能可在器件运行时
动态更新。
RP 测量的器件间偏差为 1%
电源电流:
–
–
–
关断模式下为 1.4µA
休眠模式下为 135µA
电感感测技术可实现对线性/角位置、位移、运动、压
缩、振动、金属成分以及市面上包括汽车、消费类、计
算机、工业、医疗和通信应用在内的很多其他应用的高
精度测量。 电感感测技术能够以低于其他竞争对手解
决方案的成本提供更为出色的性能和可靠性。
激活模式下为 1.9mA(未连接传感器)
•
•
距离分辨率可达亚微米级
支持远程放置传感器,以便将 LDC 与恶劣环境隔
离
•
•
•
•
可防水、油、污垢、灰尘等环境干扰
外部组件数极少
LDC1101 在小型 3mm × 3mm 10 引脚 VSON 封装内
即可提供这些电感感测技术优势。 微控制器可使用 4
引脚 SPI™轻松配置 LDC1101。
无磁体操作
工作温度范围:-40°C 至 125℃
2 应用
器件信息(1)
器件型号
LDC1101
封装
VSON (10)
封装尺寸(标称值)
•
•
•
•
•
•
•
•
高速轮齿计数
3.00mm × 3.00mm
高速事件计数
(1) 如需了解所有可用封装,请见数据表末尾的可订购产品附录。
电机转速感测
家用电器、汽车和消费类应用中的旋钮和拨盘
家用电器、汽车和消费类应用中的人机界面 (HMI)
按钮和键盘
电机控制
金属探测
4 简化电路原理图
1.8V
1.8V
VDD
CLKIN
LDC1101
High Res
CLKOUT
VDD
CLDO
Sensor
MCU
Registers
+ Logic
L Meas
INA
INB
Sensor
Driver
CSB
CSB
RP + L
Meas
SCLK
SDI
SCLK
SPI
Peripheral
SPI
MOSI
MISO
SDO
Threshold
Compare
GND
GND
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
English Data Sheet: SNOSD01
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
目录
8.4 Device Functional Modes........................................ 10
8.5 Programming.......................................................... 12
8.6 Register Maps ........................................................ 14
Application and Implementation ........................ 29
9.1 Application Information............................................ 29
9.2 Typical Application ................................................. 39
1
2
3
4
5
6
7
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
简化电路原理图........................................................ 1
修订历史记录 ........................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
7.1 Absolute Maximum Ratings ...................................... 4
7.2 ESD Ratings ............................................................ 4
7.3 Recommended Operating Conditions....................... 4
7.4 Thermal Information.................................................. 4
7.5 Electrical Characteristics........................................... 5
7.6 Digital Interface ......................................................... 5
7.7 Timing Requirements ............................................... 6
7.8 Typical Characteristics.............................................. 7
Detailed Description .............................................. 9
8.1 Overview ................................................................... 9
8.2 Functional Block Diagram ......................................... 9
8.3 Feature Description................................................... 9
9
10 Power Supply Recommendations ..................... 44
11 Layout................................................................... 44
11.1 Layout Guidelines ................................................. 44
11.2 Layout Example .................................................... 45
12 器件和文档支持 ..................................................... 46
12.1 器件支持 ............................................................... 46
12.2 文档支持................................................................ 46
12.3 社区资源................................................................ 46
12.4 商标....................................................................... 46
12.5 静电放电警告......................................................... 46
12.6 术语表 ................................................................... 46
13 机械、封装和可订购信息....................................... 46
8
5 修订历史记录
Changes from Original (May 2015) to Revision A
Page
•
已添加 完整数据表以替代产品预览......................................................................................................................................... 1
2
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
6 Pin Configuration and Functions
DRC Package
10-Pin VSON
Top View
SDO/INTB
CLKIN
SCLK
CLDO
VDD
GND
INA
1
2
10
9
3
4
DAP
8
SDI
7
CSB
5
6
INB
Pin Functions
PIN
TYPE(1)
DESCRIPTION
NAME
CLDO
CLKIN
NO.
10
2
P
I
Internal LDO bypassing pin. A 15 nF capacitor must be connected from this pin to GND.
External time-base Clock Input
SPI CSB. Multiple devices can be connected on the same SPI bus and CSB can be used to uniquely
select desired device
CSB
5
I
DAP
GND
INA
–
8
7
6
3
4
–
G
A
A
I
Connect to Ground for improved thermal performance(2)
Ground
External LC tank – connected to external LC tank
External LC tank – connected to external LC tank
SPI Clock Input
INB
SCLK
SDI
I
SPI Data Input – connect to MOSI of SPI master
SPI Data Output/INTB – Connect to MISO of SPI Master. When CSB is high, this pin is High-Z.
Alternatively, this pin can be configured to function as INTB
SDO/INTB
VDD
1
9
O
P
Power Supply
(1) P= Power, G=Ground, I=Input, O=Output, A=Analog
(2) There is an internal electrical connection between the exposed Die Attach Pad (DAP) and the GND pin of the device. Although the DAP
can be left floating, for best performance the DAP should be connected to the same potential as the device's GND pin. Do not use the
DAP as the primary ground for the device. The device GND pin must always be connected to ground.
Copyright © 2015, Texas Instruments Incorporated
3
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN
MAX
3.6
UNIT
V
VDD
Vi
Supply voltage range
Voltage on INA, INB
Voltage on CLDO
Voltage on any other pin(2)
Junction temperature
Storage temperature
–0.3
–0.3
–0.3
–55
–65
2.3
V
1.9
V
VDD+0.3
125
V
TJ
°C
°C
Tstg
125
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) Maximum voltage across any two pins is VDD+0.3.
7.2 ESD Ratings
VALUE
±2000
±1000
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
Electrostatic
discharge
V(ESD)
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN NOM
MAX
3.46
125
UNIT
V
VDD
TJ
Supply voltage
1.71
–40
Junction temperature
°C
7.4 Thermal Information
LDC1101
THERMAL METRIC(1)
DRC (VSON)
10 PINS
44.2
UNIT
RθJA
Junction-to-ambient thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
50.1
19.6
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
0.7
ψJB
19.8
RθJC(bot)
4.4
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
4
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
7.5 Electrical Characteristics
Over recommended operating conditions unless otherwise noted. VDD = 1.8 V, TA = 25°C.
PARAMETER
TEST CONDITION(1)
MIN(2)
TYP(3)
MAX(2)
UNIT
POWER
VDD
Supply voltage
Supply current
1.71
3.46
2.7
V
IDD
START_CONFIG= 0x00, no sensor connected
1.9
3.2
mA
ƒCLKIN = 16 MHz, ƒSENSOR = 2 MHz,
START_CONFIG = 0x00
Supply current including sensor
current
IDDS
mA
IDDSL
Sleep mode supply current
START_CONFIG =0x01
135
1.4
180
6.7
µA
µA
ISD
Shutdown mode supply current
SENSOR
RESP_TIME= 6144, D_CONFIG=0x00,
ALT_CONFIG=0x00, START_CONFIG = 0x00,
ƒSENSOR = 2 MHz
RP Measurement part-to-part
variation
1%
0.6
4.7
RP_MIN = b111, START_CONFIG=0x00,
D_CONFIG=0x00, ALT_CONFIG=0x00
ISENSORMAX
Sensor maximum current drive
Sensor minimum current drive
0.598
0.5
0.602
10
mA
µA
RP_MAX = b000, RPMAX_DIS=b0,
START_CONFIG=0x00, D_CONFIG=0x00,
ALT_CONFIG=0x00
ISENSORMIN
Device settings and Sensor compliant as detailed in
LDC1101 RP Configuration
ƒSENSOR
RPRES
Sensor resonant frequency
RP Measurement resolution
MHz
bits
16
16
Inductance sensing resolution –
RP+L Mode
bits
LRES
Inductance sensing resolution –
LHR Mode
24
bits
VPP
INA – INB, START_CONFIG=0x00,
D_CONFIG=0x00, ALT_CONFIG=0x00
AOSC
Sensor oscillation amplitude
1.2
DETECTION
tS_MIN
Minimum response time (RP+L
mode)
192
÷ƒSENSOR
RP+L Mode, RESP_TIME=b010
RP+L Mode, RESP_TIME=b111
s
s
Maximum response time (RP+L
mode)
6144
÷ƒSENSOR
tS_MAX
(220+39)
÷ƒCLKIN
High Res L maximum measurement LHR_REF_COUNT=0xFFFF,
Ts_MAX
SRMAXRP
SRMAXL
s
interval
START_CONFIG=0x00
ƒCLKIN=16 MHz, ƒSENSOR = 10 MHz,
RESP_TIME=b010
RP+L Mode maximum sample rate
156.25
183.8
kSPS
kSPS
High Res L Mode Maximum Sample High Resolution L Mode,
Rate LHR_REF_COUNT=0x0002, ƒCLKIN=16 MHz
FREQUENCY REFERENCE
fCLKIN
DCfin
VIH
Reference input frequency
1
16
MHz
Reference duty cycle
40%
60%
Input high voltage (Logic “1”)
Input low voltage (Logic “0”)
0.8×VDD
0.2×VDD
V
V
VIL
(1) Register values are represented as either binary (b is the prefix to the digits), or hexadecimal (0x is the prefix to the digits). Decimal
values have no prefix.
(2) Limits are ensured by testing, design, or statistical analysis at 25°C. Limits over the operating temperature range are ensured through
correlation using statistical quality control (SQC) method.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not guaranteed on
shipped production material.
7.6 Digital Interface
PARAMETER
MIN
TYP
MAX
UNIT
V
VOLTAGE LEVELS
0.8×VDD
VIH
Input high voltage (Logic “1”)
Input low voltage (Logic “0”)
0.2×VDD
V
VIL
VDD–0.3
V
VOH
VOL
IOHL
Output high voltage (Logic “1”, ISOURCE = 400 µA)
Output low voltage (Logic “0”, ISINK = 400 µA)
Digital IO leakage current
0.3
V
–500
500
nA
Copyright © 2015, Texas Instruments Incorporated
5
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
7.7 Timing Requirements
MIN
TYP
MAX
UNIT
tSTART
tWAKE
Start-up time from shutdown to sleep
0.8
ms
Wake-up time (from completion of SPI to conversion start; does not include
sensor settling time)
0.04
ms
INTERFACE TIMING REQUIREMENTS(1)
ƒSCLK
twH
Serial clock frequency
SCLK pulse-width high
SCLK pulse-width low
SDI setup time
8
MHz
s
0.4 / ƒSCLK
0.4 / ƒSCLK
10
twL
s
tsu
ns
ns
ns
ns
ns
ns
ns
ns
ns
th
SDI hold time
10
tODZ
tOZD
tOD
SDO driven-to-tristate time
SDO tristate-to-driven time
SDO output delay time
CSB setup time
25
25
20
tsu(CS)
th(CS)
tIAG
20
20
CSB hold time
CSB inter-access interval
Data ready pulse width
100
tw(DRDY)
1/ƒSENSOR
(1) Unless otherwise noted, all limits specified at TA = 25°C, VDD = 1.8 V, 10 pF capacitive load in parallel with a 10 kΩ load on the SDO
pin. Specified by design; not production tested.
SCLK
twH
th
twL
tsu
Valid Data
Valid Data
SDI
Figure 1. Write Timing Diagram
1st Clock
8th Clock
16th Clock
SCLK
tsu(CS)
ttIAG
t
tth(CS)
t
CSB
tOZD
D7
tOD
tODZ
SDO
D0
D1
Figure 2. Read Timing Diagram
6
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
7.8 Typical Characteristics
2.6
2.5
2.4
2.3
2.2
2.1
2
VDD = 1.8 V
VDD = 2.1 V
VDD = 2.4 V
VDD = 2.7 V
VDD = 3.0 V
VDD = 3.3 V
2.5
2.4
2.3
2.2
2.1
2
1.9
1.8
1.7
1.6
1.5
1.4
1.9
1.8
1.7
1.6
-40°C
-20°C
25°C
100°C
125°C
-40
0
40
80
120
1.7
2
2.3
2.6
2.9
3.2
3.5
Temperature (°C)
VDD (V)
D001
D002
Not including sensor current, default register settings.
Not including sensor current, default register settings.
Figure 3. IDD vs Temperature
Figure 4. IDD vs VDD
3.35
300
VDD = 1.8 V
VDD = 2.7 V
VDD = 3.3 V
VDD = 1.8 V
VDD = 2.1 V
VDD = 2.4 V
VDD = 2.7 V
VDD = 3.0 V
VDD = 3.3 V
3.3
3.25
3.2
250
200
150
100
50
3.15
3.1
3.05
3
2.95
0
-40
8
9
10
11
12
13
14
15
16
0
40
80
120
fCLKIN (MHz)
D003
Temperature (°C)
D004
Including sensor current. 13mm diameter sensor 0.1mm
spacing/0.1mm trace width/ 4 layer 28 turns, fSENSOR = 2 MHz,
RP_SET = 0x07, TX1=0x50, TC2=0x80, RCOUNT=0xFFFF,
RESP_TIME =6144
Figure 5. Supply Current (mA) vs ƒCLKIN (MHz) at 25°C
Figure 6. IDD Sleep Mode vs Temperature
300
14
12
10
8
VDD = 1.8 V
VDD = 2.1 V
VDD = 2.4 V
VDD = 2.7 V
VDD = 3.0 V
VDD = 3.3 V
250
200
150
6
100
-40°C
-20°C
4
25°C
100°C
125°C
50
2
0
0
1.7
2
2.3
2.6
2.9
3.2
3.5
-40
0
40
80
120
VDD (V)
Temperature (°C)
D005
D006
Figure 7. IDD Sleep Mode vs VDD
Figure 8. IDD Shutdown vs Temperature
Copyright © 2015, Texas Instruments Incorporated
7
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Typical Characteristics (continued)
610
608
606
604
602
600
598
596
594
592
590
16
-40°C
25°C
125°C
-40°C
-20°C
25°C
100°C
125°C
14
12
10
8
6
4
2
0
1.7
2
2.3
2.6
2.9
3.2
3.5
1.7
2
2.3
2.6
2.9
3.2
3.5
VDD (V)
VDD (V)
D007
D008
RP_SET.RPMIN = b111
Figure 9. IDD Shutdown vs VDD
Figure 10. ISENSOR-MAX vs VDD
4.8
4.75
4.7
4.65
-40°C
25°C
125°C
4.6
1.7
2
2.3
2.6
2.9
3.2
3.5
VDD (V)
D009
RP_SET.RPMAX = b000
Figure 11. ISENSOR-MIN vs VDD
8
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
8 Detailed Description
8.1 Overview
The LDC1101 is an inductance-to-digital converter which can simultaneously measure the impedance and
resonant frequency of an LC resonator. The high resolution measurement capability enables this device to be
used to directly measure changes in physical systems, allowing the resonator to sense the proximity and
movement of conductive materials.
The LDC1101 measures the impedance and resonant frequency by regulating the oscillation amplitude in a
closed-loop configuration at a constant level, while monitoring the energy dissipated by the resonator. By
monitoring the amount of power injected into the resonator, the LDC1101 can determine the equivalent parallel
resistance of the resonator, RP, which it returns as a digital value.
In addition, the LDC1101 device also measures the oscillation frequency of the LC circuit by comparing the
sensor frequency to a provided reference frequency. The sensor frequency can then be used to determine the
inductance of the LC circuit.
The threshold comparator block can compare the RP+L conversion results versus a programmable threshold.
With the threshold registers programmed and comparator enabled, the LDC1101 can provide a switch output,
reported as a high/low level on the INTB/SDO pin.
The LDC1101 device supports a wide range of LC combinations with oscillation frequencies ranging from 500
kHz to 10 MHz and RP ranging from 1.25 kΩ to 90 kΩ. The device is configured and conversion results retrieved
through a simple 4-wire SPI. The power supply for the device can range from 1.8 V – 5% to 3.3 V + 5%. The
only external components necessary for operation are a 15 nF capacitor for internal LDO bypassing and supply
bypassing for VDD.
8.2 Functional Block Diagram
VDD
LDC1101
CLKIN
CLDO
High Res
L Meas
Registers
+ Logic
INA
INB
Sensor
Driver
CSB
RP + L
Meas
SCLK
SDI
SPI
SDO
Threshold
Compare
GND
8.3 Feature Description
8.3.1 Sensor Driver
The LDC1101 can drive a sensor with a resonant frequency of 500 kHz to 10 MHz with an RP in the range of
1.25 kΩ to 90 kΩ. The nominal sensor amplitude is 1.2 V. The sensor Q should be at least 10 for RP
measurements. The inductive sensor must be connected across the INA and INB pins. The resonant frequency
of the sensor is set by:
1
ƒSENSOR Hz =
( )
2p L ´C
where
•
•
L is the sensor inductance in Henrys, and
C is the sensor parallel capacitance in Farads.
(1)
9
Copyright © 2015, Texas Instruments Incorporated
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
8.4 Device Functional Modes
8.4.1 Measurement Modes
The LDC1101 features two independent measurement subsystems to measure the impedance and resonant
frequency of an attached sensor. The RP+L subsystem can simultaneously measure the impedance and
resonant frequency of an LC resonator, with up to 16 bits of resolution for each parameter. Refer to RP+L
Measurement Mode for more information on the RP+L measurement functionality.
The High Resolution L (LHR) subsystem measures the sensor resonant frequency with up to 24 bits of
resolution. The effective resolution is a function of the sample rate and the reference frequency supplied on the
CLKIN pin. Refer to High Resolution L (LHR) Measurement Mode for more information on the LHR measurement
functionality.
Both measurement subsystems can convert simultaneously but at different sample intervals – the completion of
an RP+L conversion will be asynchronous to the completion of a LHR conversion.
Table 1. Comparison of Measurement Modes
RP+L Mode
LHR Mode
RP Measurement Resolution
16 bits
N/A
L Measurement Resolution
16 bits
24 bits
Sample Rate configuration
Varies with ƒSENSOR, set by RESP_TIME
Fixed and set by RCOUNT field and ƒCLKIN
Sample rate at highest resolution (SPS)
Maximum Sample Rate (kSPS)
L Resolution at Maximum Sample rate
Switch Output on SDO/INTB
244
156.25
15.3
183.9
6.5 bits
N/A
6.7 bits
Available for RP or L output code
8.4.2 RP+L Measurement Mode
In RP+L mode, the LDC1101 will simultaneously measure the impedance and resonant frequency of the
attached sensor. The device accomplishes this task by regulating the oscillation amplitude in a closed-loop
configuration to a constant level, while monitoring the energy dissipated by the resonator. By monitoring the
amount of power injected into the resonator, the LDC1101 device can determine the value of RP. The device
returns this value as a digital value which is proportional to RP. In addition, the LDC1101 device can also
measure the oscillation frequency of the LC circuit, by counting the number of cycles of a reference frequency.
The measured sensor frequency can be used to determine the inductance of the LC circuit.
8.4.2.1 RPMIN and RPMAX
The variation of RP in a given system is typically much smaller than maximum range of 1.25 kΩ to >90 kΩ
supported by the LDC1101. To achieve better resolution for systems with smaller RP ranges, the LDC1101
device offers a programmable RP range.
The LDC1101 uses adjustable current drives to scale the RP measurement range; by setting a tighter current
range a higher accuracy RP measurement can be performed. This functionality can be considered as a variable
gain amplifier (VGA) front end to an ADC. The current ranges are configured in the RPMIN and RPMAX fields of
register RP_SET (address 0x01). Refer to LDC1101 RP Configuration for instructions to optimize these settings.
8.4.2.2 Programmable Internal Time Constants
The LDC1101 utilizes internal programmable registers to configure time constants necessary for sensor
oscillation. These internal time constants must be configured for RP measurements. Refer to Setting Internal
Time Constant 1 and Setting Internal Time Constant 2 for instructions on how to configure them for a given
system.
8.4.2.3 RP+L Mode Measurement Sample Rate
The LDC1101 provides an adjustable sample rate for the RP+L conversion, where longer conversion times have
higher resolution. Refer to RP+L Sample Rate Configuration with RESP_TIME for more details.
10
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
8.4.3 High Resolution L (LHR) Measurement Mode
The High Resolution L measurement (LHR) subsystem provides a high-resolution inductance (L) measurement
of up to 24 bits. This L measurement can be configured to provide a higher resolution measurement than the
measurement returned from the RP+L subsystem. The LHR subsystem also provides a constant conversion time
interval, whereas the RP+L conversion interval is a function of the sensor frequency. The LHR measurement
runs asynchronously with respect to the RP+L measurement.
8.4.4 Reference Count Setting
The LHR sample rate is set by the Reference Count (LHR_RCOUNT) setting (registers 0x30 and 0x31). The
LHR conversion resolution is proportional to the programmed RCOUNT value. With the maximum supported 16
MHz CLKIN input, the LDC1101 conversion interval can be set from 8.6 µs to 87.38 ms in 1 µs increments. Note
that longer conversion intervals produce more accurate LHR measurements. Refer to LHR Sample Rate
Configuration with RCOUNT for more details.
8.4.5 L-Only Measurement Operation
The LDC1101 can disable the RP measurement to perform a more stable L measurement. To enable this mode,
set:
•
•
ALT_CONFIG.LOPTIMAL(register 0x05-bit0) = 1
D_CONFIG.DOK_REPORT (register 0x0C-bit0) = 1
When this mode is used, RP measurement results are not valid.
8.4.6 Minimum Sensor Frequency and Watchdog Setting
The LDC1101 can report an error condition if the sensor oscillation stops. Refer to MIN_FREQ and Watchdog
Configuration for information on the configuration of the watchdog.
8.4.7 Low Power Modes
When continuous LDC conversions are not required, the LDC1101 supports two reduced power modes. In Sleep
mode, the LDC1101 retains register settings and can quickly enter active mode for conversions. In Shutdown
mode, power consumption is significantly lower, although the device configuration is not retained. While in either
low power mode, the LDC1101 will not perform conversions.
8.4.7.1 Shutdown Mode
Shutdown mode is the lowest power state for the LDC1101. Note that entering SD mode will reset all registers to
their default state, and so the device must have its registers rewritten. To enter Shutdown, perform the following
sequence:
1. Set ALT_CONFIG.SHUTDOWN_EN = 1 (register 0x05-bit[1]).
2. Stop toggling the CLKIN pin input and drive the CLKIN pin Low.
3. Set START_CONFIG.FUNC_MODE = b10 (register 0x0B:bits[1:0]). This register can be written while the
LDC1101 is in active mode; on completion of the register write the LDC1101 will enter shutdown.
To exit Shutdown mode, resume toggling the clock input on the CLKIN pin; the LDC1101 will transition to Sleep
mode with the default register values.
While in Shutdown mode, no conversions are performed. In addition, entering Shutdown mode will clear the
status registers; if an error condition is present it will not be reported when the device exits Shutdown mode.
8.4.7.2 Sleep Mode
Sleep mode is entered by setting START_CONFIG.FUNC_MODE =b01 (register 0x0B:bits[1:0]). While in this
mode, the register contents are maintained. To exit Sleep mode and start active conversions, set
START_CONFIG.FUNC_MODE = b00. While in Sleep mode the SPI interface is functional so that register reads
and writes can be performed.
On power-up or exiting Shutdown mode, the LDC1101 will be in Sleep mode.
Copyright © 2015, Texas Instruments Incorporated
11
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Configuring the LDC1101 must be done while the device is in Sleep mode. If a setting on the LDC1101 needs to
be changed, return the device to Sleep mode, change the appropriate register, and then return the LDC1101 to
conversion mode. The registers related to INTB reporting can be changed while the LDC1101 is in active mode.
Refer to INTB Reporting on SDO for more details.
8.4.8 Status Reporting
The LDC1101 provides 2 status registers, STATUS and LHR_STATUS, to report on the device and sensor
condition.
Table 2. STATUS Fields
NAME
FIELD
FUNCTION
When the resonance impedance of the sensor, RP, drops below the programed Rp_MIN, the sensor
oscillation may stop. This condition is reported by STATUS:NO_SENSOR_OSC (register 0x20-bit7). This
condition could occur when a target comes too close to the sensor or if RP_SET:RP_MIN (register 0x01-
bits[2:0]) is set too high.
NO_SENSOR_OSC
7
DRDYB
6
5
4
3
2
0
RP+L Data Ready - reports completion of RP+L conversion results
RP_HIN
RP_HI_LON
L_HIN
RP+L threshold – refer to Comparator Functionality for details
L_HI_LON
POR_READ
Device in Power-On Reset – device should only be configured when POR_READ = 0.
The LHR_STATUS register (register 0x3B) reports on LHR functionality.
8.4.9 Switch Functionality and INTB Reporting
The SDO pin can generate INTB, a signal which corresponds to device status. INTB can report conversion
completion or provide a comparator output, in which the LDC conversion results are internally compared to
programmable thresholds. Refer to INTB Reporting on SDO for details.
8.5 Programming
8.5.1 SPI Programming
The LDC1101 uses SPI to configure the internal registers. It is necessary to configure the LDC1101 while in
Sleep mode. If a setting on the LDC1101 needs to be changed, return the device to Sleep mode, change the
appropriate register, and then return the LDC1101 to conversion mode. CSB must go low before accessing first
address. If the number of SCLK pulses is less than 16, a register write command will not change the contents of
the addressed register.
12
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
Programming (continued)
CSB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SCK
tCOMMAND FIELDt
tDATA FIELDt
MSB
LSB
__
R/W
SDI
A0
D6
A6
A5
A4
A3
A2
A1
D7
D5
D5
D4
D3
D2
D1
D0
Address (7 bits)
Write Data (8-bits)
MSB
LSB
SDO
D6
D7
D4
D3
D2
D1
D0
R/W = Instruction
1: Read
Read Data (8-bits)
0: Write
Figure 12. SPI Transaction Format
The LDC1101 supports an extended SPI transaction, in which CSB is held low and sequential register addresses
can be written or read. After the first register transaction, each additional 8 SCLK pulses will address the next
register, reading or writing based on the initial R/W flag in the initial command. A register write command will take
effect on the 8th clock pulse. Two or more registers can be programmed using this method. The register address
must not increment above 0x3F.
CSB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
SCK
COMMAND FIELD
DATA FIELD for ADDRESS A
DATA FIELD for ADDRESS A+1
MSB
LSB MSB
LSB
__
R/W
SDI
A0
D6
D6
D6
A6
A5
A4
A3
A2
A1
D7
D5
D4
D3
D2
D1
D1
D0
D7
D5
D4
D3
D2
D1
D1
D0
Write Data to Address A+1
(8-bits)
Write Data to Address A
(8-bits)
Address (7 bits)
MSB
LSB
MSB
LSB
SDO
D6
D7
D5
D4
D3
D2
D0
D7
D5
D4
D3
D2
D0
R/W = Instruction
1: Read
0: Write
Read Data from Address A+1
(8-bits)
Read Data from Address A
(8-bits)
Figure 13. Extended SPI Transaction
Copyright © 2015, Texas Instruments Incorporated
13
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
8.6 Register Maps
Table 3. Register List
DEFAULT
VALUE
ADDRESS
NAME
DESCRIPTION
0x01
0x02
0x03
0x04
0x05
RP_SET
TC1
0x07
0x90
0xA0
0x03
0x00
Configure RP Measurement Dynamic Range
Configure Internal Time Constant 1
Configure Internal Time Constant 2
Configure RP+L conversion interval
Configure additional device settings
TC2
DIG_CONFIG
ALT_CONFIG
RP_THRESHOLD High Setting – bits 7:0. This register can be modified while
the LDC1101 is in active mode.
0x06
0x07
0x08
0x09
0x0A
RP_THRESH_H_LSB
RP_THRESH_H_MSB
RP_THRESH_L_LSB
RP_THRESH_L_MSB
INTB_MODE
0x00
0x00
0x00
0x00
0x00
RP_THRESHOLD High Setting – bits 15:8. This register can be modified while
the LDC1101 is in active mode.
RP_THRESHOLD Low Setting – bits 7:0. This register can be modified while the
LDC1101 is in active mode.
RP_THRESHOLD Low Setting – bits 15:8. This register can be modified while
the LDC1101 is in active mode.
Configure INTB reporting on SDO pin. This register can be modified while the
LDC1101 is in active mode.
0x0B
0x0C
START_CONFIG
D_CONF
0x01
0x00
Configure Power State
Sensor Amplitude Control Requirement
L_THRESHOLD High Setting – bits 7:0. This register can be modified while the
LDC1101 is in active mode.
0x16
0x17
0x18
0x19
L_THRESH_HI_LSB
L_THRESH_HI_MSB
L_THRESH_LO_LSB
L_THRESH_LO_MSB
0x00
0x00
0x00
0x00
L_THRESHOLD High Setting – bits 15:8. This register can be modified while the
LDC1101 is in active mode.
L_THRESHOLD Low Setting – bits 7:0. This register can be modified while the
LDC1101 is in active mode.
L_THRESHOLD Low Setting – bits 15:8. This register can be modified while the
LDC1101 is in active mode.
0x20
0x21
0x22
0x23
0x24
0x30
0x31
0x32
0x33
0x34
0x38
0x39
0x3A
0x3B
0x3E
0x3F
STATUS
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x02
0xD4
Report RP+L measurement status
RP_DATA_LSB
RP_DATA_MSB
L_DATA_LSB
RP Conversion Result Data Output - bits 7:0
RP Conversion Result Data Output - bits 15:8
L Conversion Result Data Output - bits 7:0
L Conversion Result Data Output - bits 15:8
High Resolution L Reference Count – bits 7:0
High Resolution L Reference Count – bits 15:8
High Resolution L Offset – bits 7:0
L_DATA_MSB
LHR_RCOUNT_LSB
LHR_RCOUNT_MSB
LHR_OFFSET_LSB
LHR_OFFSET_MSB
LHR_CONFIG
LHR_DATA_LSB
LHR_DATA_MID
LHR_DATA_MSB
LHR_STATUS
RID
High Resolution L Offset – bits 15:8
High Resolution L Configuration
High Resolution L Conversion Result Data output - bits 7:0
High Resolution L Conversion Result Data output - bits 15:8
High Resolution L Conversion Result Data output - bits 23:16
High Resolution L Measurement Status
Device RID value
CHIP_ID
Device ID value
14
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
8.6.1 Individual Register Listings
Fields indicated with Reserved must be written only with indicated values. Improper device operation may occur
otherwise. The R/W column indicates the Read-Write status of the corresponding field. A ‘R/W’ entry indicates
read and write capability, a ‘R’ indicates read-only, and a ‘W’ indicates write-only.
8.6.2 Register RP_SET (address = 0x01) [reset = 0x07]
Figure 14. Register RP_SET
7
6
5
4
3
2
1
0
RPMAX_DIS
R/W
RP_MAX
R/W
RESERVED
R/W
RP_MIN
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 4. Register RP_SET Field Descriptions
Bit
Field
Type
Reset Description
RP_MAX Disable
7
RPMAX_DIS
R/W
This setting improves the RP measurement accuracy for very high Q coils by
driving 0A as the RPMAX current drive.
b0: Programmed RP_MAX is driven (default value)
b1: RP_MAX current is ignored; current drive is off.
6:4
RP_MAX
R/W
RP_MAX Setting
Set the maximum input dynamic range for the sensor RP measurement. The
programmed RP_MIN setting must not exceed the programmed RP_MAX setting.
b000: RPMAX = 96 kΩ (default value)
b001: RPMAX = 48 kΩ
b010: RPMAX = 24 kΩ
b011: RPMAX = 12 kΩ
b100: RPMAX = 6 kΩ
b101: RPMAX = 3 kΩ
b110: RPMAX = 1.5 kΩ
b111: RPMAX = 0.75 kΩ
3
RESERVED
RP_MIN
R/W
R/W
Reserved. Set to 0
2:0
RP_MIN Setting
Set the minimum input dynamic range for the sensor RP measurement. The
programmed RP_MIN setting must not exceed the programmed RP_MAX setting.
b000: RPMIN = 96 kΩ
b001: RPMIN = 48 kΩ
b010: RPMIN = 24 kΩ
b011: RPMIN = 12 kΩ
b100: RPMIN = 6 kΩ
b101: RPMIN = 3 kΩ
b110: RPMIN = 1.5 kΩ
b111: RPMIN = 0.75 kΩ (default value)
Copyright © 2015, Texas Instruments Incorporated
15
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
8.6.3 Register TC1 (address = 0x02) [reset = 0x90]
Figure 15. Register TC1
7
6
5
4
3
2
1
0
C1
RESERVED
R/W
R1
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 5. Register TC1 Field Descriptions
Bit
Field
Type
Reset Description
Internal Time Constant 1 Capacitance
7:6
C1
R/W
This sets the capacitive component used to configure internal time constant 1.
Refer to Setting Internal Time Constant 1 for more details.
b00: C1 = 0.75 pF
b01: C1 = 1.5 pF
b10: C1 = 3.0 pF (default value)
b11: C1 = 6.0 pF
5
RESERVED
R1
R/W
R/W
Reserved. Set to 0
4:0
Internal Time Constant 1 Resistance
This sets the resistive component used to configure internal time constant 1.
Refer to Setting Internal Time Constant 1 for configuration details.
R1(Ω) = -12.77 kΩ × R1 + 417 kΩ
Valid Values: [b0’0000:b1’1111]
b0’0000: R1 = 417 kΩ
b1’0000: R1 = 212.7kΩ (default value)
b1’1111: R1 = 21.1 kΩ
8.6.4 Register TC2 (address = 0x03) [reset = 0xA0]
Figure 16. Register TC2
7
6
5
4
3
2
1
0
C2
R2
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 6. Register TC2 Field Descriptions
Bit
Field
Type
Reset
Description
7:6
C2
R/W
Internal Time Constant 2 Capacitance
This sets the capacitive component used to configure internal time constant 2.
Refer to Setting Internal Time Constant 2 for configuration details.
b00: C2 = 3 pF
b01: C2 = 6 pF
b10: C2 = 12 pF (default value)
b11: C2 = 24 pF
5:0
R2
R/W
Internal Time Constant 2 Resistance
This sets the resistive component used to configure internal time constant 2.
Refer to Setting Internal Time Constant 2 for details.
R2(Ω) = -12.77 kΩ × R2 + 835 kΩ
Valid Values: [b00’0000:b11’1111]
b00’0000: R2 = 835kΩ
b10’0000: R2 = 426.4 kΩ (default value)
b11’1111: R2 = 30.5 kΩ
8.6.5 Register DIG_CONF (address = 0x04) [reset = 0x03]
16
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
Figure 17. Register DIG_CONF
7
6
5
4
3
2
1
0
MIN_FREQ
R/W
RESERVED
R/W
RESP_TIME
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 7. Register DIG_CONF Field Descriptions
Bit
Field
Type
Reset
Description
7:4
MIN_FREQ
R/W
Sensor Minimum Frequency
Configure this register based on the lowest possible sensor frequency. This is
typically when the target is providing minimum interaction with the sensor,
although with some steel and ferrite targets, the minimum sensor frequency
occurs with maximum target interaction.
This setting should include any additional effects which reduce the sensor
frequency, including temperature shifts and sensor capacitor variation.
MIN_FREQ = 16 – (8 MHz ÷ ƒSENSORMIN
)
b0000: ƒSENSORMIN = 500 kHz (default value)
b1111: ƒSENSORMIN = 8 MHz
3
RESERVED
RESP_TIME
R/W
R/W
Reserved. Set to 0
2:0
Measurement Response Time Setting
Sets the Response Time, which is the number of sensor periods used per
conversion. This setting applies to the RP and Standard Resolution
L
measurement, but not the High Resolution L measurement. This corresponds
to the actual conversion time by:
Re sponseTime
ConversionTime s
=
( )
3 ´ ƒSENSOR
b000: Reserved (do not use)
b001: Reserved (do not use)
b010: Response Time = 192
b011: Response Time = 384 (default value)
b100: Response Time = 768
b101: Response Time = 1536
b110: Response Time = 3072
b111: Response Time = 6144
8.6.6 Register ALT_CONFIG (address = 0x05) [reset = 0x00]
Figure 18. Register ALT_CONFIG
7
6
5
4
3
2
1
0
RESERVED
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
SHUTDOWN_EN
R/W
LOPTIMAL
R/W
Table 8. Register ALT_CONFIG Field Descriptions
Bit
7:2
1
Field
Type
R/W
R/W
Reset
Description
RESERVED
SHUTDOWN_EN
Reserved. Set to b00'0000.
Shutdown Enable
Enables shutdown mode of operation. If SHUTDOWN_EN is not set to 1,
then SHUTDOWN (Address 0x0B:[1]) will not have any effect.
b0: Shutdown not enabled. (default value) b1: Shutdown functionality
enabled.
Copyright © 2015, Texas Instruments Incorporated
17
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Table 8. Register ALT_CONFIG Field Descriptions (continued)
Bit
Field
Type
Reset
Description
0
LOPTIMAL
R/W
Optimize for L Measurements
Optimize sensor drive signal for L measurements (for both High-Res L and L
measurement). When LOPTIMAL is enabled, RP measurements will not be
completed. It is also necessary to set DOK_REPORT=1 when this mode is
enabled.
b0: L optimal disabled; both RP+L/LHR measurements (default value)
b1: Only perform LHR and/or L-only measurements. RP measurements are
invalid.
8.6.7 Register RP_THRESH_HI_LSB (address = 0x06) [reset = 0x00]
This register can be modified while the LDC1101 is in active mode.
Figure 19. Register RP_THRESH_HI_LSB
7
6
5
4
3
2
1
0
RP_THRESH_HI_LSB
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 9. Register RP_THRESH_HI_LSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
RP_THRESH_HI_LSB
R/W
RP High Threshold LSB Setting
Combine with value in Register RP_THRESH_HI_MSB (Address 0x07) to
set the upper RP conversion threshold:
RP_THRESH_HI = RP_THRESH_HI[15:8] × 256 + RP_THRESH_HI[7:0]
If RP_DATA conversion result is greater than the RP_THRESH_HI,
RP_TH_I will be asserted.
Note that RP_THRESH_HI_LSB is buffered and will not change the
device configuration until a write to RP_TRESH_HI_MSB is performed.
Note that both registers 0x06 and 0x07 must be written to change the
value of RP_THRESH_HI.
0x00: default value
8.6.8 Register RP_THRESH_HI_MSB (address = 0x07) [reset = 0x00]
This register can be modified while the LDC1101 is in active mode.
Figure 20. Register RP_THRESH_HI_MSB
7
6
5
4
3
2
1
0
RP_THRESH_HI_MSB
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 10. Register RP_THRESH_HI_MSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
RP_THRESH_HI_MSB R/W
RP High Threshold MSB Setting
Combine with value in Register RP_THRESH_HI_LSB (Address 0x06) to
set the upper RP conversion threshold.
0x00: default value
18
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
8.6.9 Register RP_THRESH_LO_LSB (address = 0x08) [reset = 0x00]
This register can be modified while the LDC1101 is in active mode.
Figure 21. Register RP_THRESH_LO_LSB
7
6
5
4
3
2
1
0
RP_THRESH_LO_LSB
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 11. Register RP_THRESH_LO_LSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
RP_THRESH_LO[7:0]
R/W
RP Low Threshold LSB Setting
Combine with value in Register RP_THRESH_LO_MSB (Address 0x09)
to set the lower RP conversion threshold:
RP_THRESH_LO = RP_THRESH_LO[15:8] ×256 +
RP_THRESH_LO[7:0]
If RP_DATA conversion result is less than the RP_THRESH_LO,
RP_HI_LON will be asserted. Note that RP_THRESH_LO_LSB is
buffered and will not change the device configuration until a write to
RP_TRESH_LO_MSB is performed.
Note that both registers 0x08 and 0x09 must be written to change the
value of RP_THRESH_LO.
0x00: default value
8.6.10 Register RP_THRESH_LO_MSB (address = 0x09) [reset = 0x00]
This register can be modified while the LDC1101 is in active mode
Figure 22. Register RP_THRESH_LO_MSB
7
6
5
4
3
2
1
0
RP_THRESH_LO_MSB
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 12. Register RP_THRESH_LO_MSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
RP_THRESH_LO_MSB[1 R/W
5:8]
RP Low Threshold MSB Setting
Combine with value in Register RP_THRESH_LO_LSB (Address 0x08)
to set the lower RP conversion threshold.
0x00: default value
8.6.11 Register INTB_MODE (address = 0x0A) [reset = 0x00]
This register can be modified while the LDC1101 is in active mode.
Figure 23. Register INTB_MODE
7
6
5
4
3
2
1
0
INTB2SDO
R/W
RESERVED
R/W
INTB_FUNC
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Copyright © 2015, Texas Instruments Incorporated
19
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Table 13. NAME Field Descriptions
Bit
Field
Type
Reset
Description
7
INTB2SDO
R/W
INTB Output on SDO
Output INTB signal on SDO pin.
b0: do not report DRDY on SDO pin (default value)
b1: report DRDY on SDO pin
6
RESERVED
INTB_FUNC
R/W
R/W
Reserved. Set to 0
5:0
Select INTB signal reporting. INTB2SDO must be set to 1 for the
selected signal to appear on the SDO pin. Refer to INTB Reporting on
SDO for configuration details.
b10’0000: Report LHR Data Ready
b01’0000: Compare L conversion to L Thresholds (hysteresis)
b00’1000: Compare L conversion to L High Threshold (latching)
b00’0100: Report RP+L Data Ready
b00’0010: Compare RP conversion to RP Thresholds (hysteresis)
b00’0001: Compare RP conversion to RP High Threshold (latching)
b00’0000: no output (default value)
All other values: Reserved
8.6.12 9.Register START_CONFIG (address = 0x0B) [reset = 0x01]
This register can be modified while the LDC1101 is in active mode.
Figure 24. Register START_CONFIG
7
6
5
4
3
2
1
0
RESERVED
R/W
FUNC_MODE
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 14. Register START_CONFIG Field Descriptions
Bit
7:2
1:0
Field
Type
R/W
R/W
Reset
Description
RESERVED
FUNC_MODE
Reserved. Set to b00’0000
Functional Mode
Configure functional mode of device. In active mode, the device
performs conversions. When in Sleep mode, the LDC1101 is in a
reduced power mode; the device should be configured in this mode.
Shutdown mode is a minimal current mode in which the device
configuration is not retained.
Note that SHUTDOWN_EN must be set to
FUNC_MODE to b10.
1
prior to setting
b00: Active conversion mode
b01: Sleep mode (default value)
b10: Set device to shutdown mode
b11: Reserved
8.6.13 Register D_CONFIG (address = 0x0C) [reset = 0x00]
Figure 25. Register D_CONFIG
7
6
5
4
3
2
1
0
RESERVED
R/W
DOK_REPORT
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
20
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
Table 15. Register D_CONFIG Field Descriptions
Bit
Field
Type
Reset
Description
7:1
RESERVED
R/W
Reserved.
Set to b000’0000.
0
DOK_REPORT
R/W
Sensor Amplitude Control
Continue to convert even if sensor amplitude is not regulated.
b0: Require amplitude regulation for conversion (default value)
b1: LDC will continue to convert even if sensor amplitude is unable to
maintain regulation.
8.6.14 Register L_THRESH_HI_LSB (address = 0x16) [reset = 0x00]
This register can be modified while the LDC1101 is in active mode.
Figure 26. Register L_THRESH_HI_LSB
7
6
5
4
3
2
1
0
L_THRESH_HI[7:0]
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 16. Register L_THRESH_HI_LSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
L_THRESH_HI[7:0]
R/W
L High Threshold LSB Setting
Combine with value in Register L_THRESH_HI_MSB (Address 0x17) to
set the upper L conversion threshold:
LThreshHI = L_THRESH_HI[15:8] ×256 + L_THRESH_HI[7:0]
If L_DATA conversion result is greater than the L_THRESH_HI, L_HIN
will be asserted. Note that L_THRESH_HI_LSB is buffered and will not
change the device configuration until a write to L_TRESH_HI_MSB.
0x00: default value
8.6.15 Register L_THRESH_HI_MSB (address = 0x17) [reset = 0x00]
This register can be modified while the LDC1101 is in active mode.
Figure 27. Register L_THRESH_HI_MSB
7
6
5
4
3
2
1
0
L_THRESH_HI[15:8]
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 17. Register L_THRESH_HI_MSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
L_THRESH_HI[15:8]
R/W
L High Threshold MSB Setting
Combine with value in Register L_THRESH_HI_LSB (Address 0x16)
to set the upper L conversion threshold.
0x00: default value
8.6.16 Register L_THRESH_LO_LSB (address = 0x18) [reset = 0x00]
This register can be modified while the LDC1101 is in active mode.
Copyright © 2015, Texas Instruments Incorporated
21
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Figure 28. Register L_THRESH_LO_LSB
7
6
5
4
3
2
1
0
L_THRESH_L[7:0]
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 18. Register L_THRESH_LO_LSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
L_THRESH_LO[7:0]
R/W
L Low Threshold LSB Setting
Combine with value in Register L_THRESH_LO_MSB (Address
0x19) to set the lower L conversion threshold:
LThreshLO = L_THRESH_LO[15:8] ×256 + L_THRESH_LO[7:0]
If L_DATA conversion result is less than the L_THRESH_LO,
L_HI_LON will be asserted.
Note that L_THRESH_LO_LSB is buffered and will not change the
device configuration until a write to L_TRESH_LO_MSB.
0x00: default value
8.6.17 Register L_THRESH_LO_MSB (address = 0x19) [reset = 0x00]
This register can be modified while the LDC1101 is in active mode.
Figure 29. L_THRESH_LO_MSB
7
6
5
4
3
2
1
0
L_THRESH_L[15:8]
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 19. L_THRESH_LO_MSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
L_THRESH_LO[15:8]
R/W
L Low Threshold MSB Setting
Combine with value in Register L_THRESH_LO_LSB (Address
0x18) to set the lower L conversion threshold.
0x00: default value
8.6.18 Register STATUS (address = 0x020 [reset = 0x00]
Figure 30. Register STATUS
7
6
DRDYB
R
5
RP_HIN
R
4
RP_HI_LON
R
3
L_HIN
R
2
L_HI_LON
R
1
RESERVED
R
0
POR_READ
R
NO_SENSOR_OSC
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 20. Register STATUS Field Descriptions
Bit
Field
Type
Reset
Description
7
NO_SENSOR_OSC
R
Sensor Oscillation Not Present Error
Indicates that the sensor has stopped oscillating. This error may also
be produced if the MIN_FREQ is set to too high a value.
b0: Error condition has not occurred
b1: LDC1101 has not detected the sensor oscillation.
6
DRDYB
R
RP+L Data Ready
b0: New RP+L conversion data is available.
b1: No new conversion data is available.
22
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
Table 20. Register STATUS Field Descriptions (continued)
Bit
Field
Type
Reset
Description
5
RP_HIN
R
RP_DATA High Threshold Comparator
Note this field will latch a low value. To clear, write 0x00 to register
0x0A. INTB_FUNC (register 0x0A:bits[5:0]) must be set to b00'0001 for
this flag to be reported.
b0: RP_DATA measurement has exceeded RP_THRESH_HI
b1: RP_DATA measurement has not exceeded RP_THRESH_HI
4
3
RP_HI_LON
L_HIN
R
R
RP_DATA Hysteresis Comparator
b0: RP_DATA measurement has gone above RP_THRESH_LO.
b1: RP_DATA measurement has gone below RP_THRESH_HI.
L_DATA High Threshold Comparator
Note this field will latch a low value. To clear, write 0x00 to register
0x0A. INTB_FUNC (register 0x0A:bits[5:0]) must be set to b00'1000 for
this flag to be reported.
b0: L_DATA measurement has exceeded L_THRESH_HI
b1: L_DATA measurement has not exceeded L_THRESH_HI
2
L_HI_LON
R
L_DATA Hysteresis Comparator
b0: L_DATA measurement has gone above L_THRESH_LO.
b1: L_DATA measurement has gone below L_THRESH_HI.
1
0
RESERVED
POR_READ
R
R
No Function
0: default value
Device in Power-On-Reset
Indicates the device is in process of resetting. Note that the device
cannot accept any configuration changes until reset is complete. Wait
until POR_READ = 0 before changing any device configuration.
b0: Device is not in reset.
b1: Device is currently in reset; wait until POR_READ = 0.
8.6.19 Register RP_DATA_LSB (address = 0x21) [reset = 0x00]
Figure 31. Register RP_DATA_LSB
7
6
5
4
3
2
1
0
RP_DATA[7:0]
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 21. Register RP_DATA_LSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
RP_DATA[7:0]
R
RP-Measurement Conversion Result
Combine with values in Register RP_DATA_MSB (Address 0x22) to
determine RP conversion result:
RP_DATA = RP_DATA[15:8]×256 + RP_DATA[7:0]
NOTE: RP_DATA_LSB (Address 0x21) must be read prior to
reading the RP_DATA_MSB (Address 0x22) register to properly
retrieve conversion results.
8.6.20 Register RP_DATA_MSB (address = 0x22) [reset = 0x00]
Figure 32. Register RP_DATA_MSB
7
6
5
4
3
2
1
0
RP_DATA[15:8]
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Copyright © 2015, Texas Instruments Incorporated
23
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Table 22. Register RP_DATA_MSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
RP_DATA[15:8]
R
RP-Measurement Conversion Result
Combine with values in Register RP_DATA_LSB (Address 0x21) to
determine RP conversion result:
NOTE: RP_DATA_LSB (Address 0x21) must be read prior to
reading this register to properly retrieve conversion results.
8.6.21 Register L_DATA_LSB (address = 0x23) [reset = 0x00]
Figure 33. Register L_DATA_LSB
7
6
5
4
3
2
1
0
L_DATA[7:0]
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 23. Register L_DATA_LSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
L_DATA[7:0]
R
L-Measurement Conversion Result
Combine with values in Register L_DATA_MSB (Address 0x24) to
determine L conversion result:
L_DATA = L_DATA[15:8]×256 + L_DATA[7:0]
fSENSOR = ( fCLKIN ˣ RESP_TIME) / (3 ˣ L_DATA)
NOTE: RP_DATA_LSB (Address 0x21) must be read prior to
reading this register to properly retrieve conversion results.
8.6.22 Register L_DATA_MSB (address = 0x24) [reset = 0x00]
Figure 34. Register L_DATA_MSB
7
6
5
4
3
2
1
0
L_DATA[15:8]
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 24. Register L_DATA_MSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
L_DATA[15:8]
R
L-Measurement Conversion Result
Combine with values in Register L_DATA_LSB (Address 0x23) to
determine L conversion result:
NOTE: RP_DATA_LSB (Address 0x21) must be read prior to
reading this register to properly retrieve conversion results.
8.6.23 Register LHR_RCOUNT_LSB (address = 0x30) [reset = 0x00]
Figure 35. Register LHR_RCOUNT_LSB
7
6
5
4
3
2
1
0
RCOUNT[7:0]
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
24
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
Table 25. Register LHR_RCOUNT_LSB Field Descriptions
Bit
Field
RCOUNT[7:0]
Type
Reset
Description
7:0
R
High Resolution L-Measurement Reference Count Setting
Combine with value in Register LHR_RCOUNT_MSB (Address
0x31) to set the measurement time for High Resolution
L
Measurements.
0x00: default value
8.6.24 Register LHR_RCOUNT_MSB (address = 0x31) [reset = 0x00]
Figure 36. Register LHR_RCOUNT_MSB
7
6
5
4
3
2
1
0
RCOUNT[15:8]
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 26. Register LHR_RCOUNT_MSB Field Descriptions
Bit
Field
Type
Reset
Description
High Resolution L-Measurement Reference Count Setting
7:0
RCOUNT[15:8]
Combine with value in Register LHR_RCOUNT_LSB (Address 0x30)
to set the measurement time for High Resolution L Measurements.
Higher values for LHR_RCOUNT have
a
higher effective
measurement resolution but a lower sample rate. Refer to LHR
Sample Rate Configuration with RCOUNT for more details.
Measurement Time (tCONV)= (RCOUNT[15:0] ˣ 16 + 55)/fCLKIN
RCOUNT = RCOUNT [15:8]×256 + RCOUNT [7:0]
Valid range: 2 ≤ RCOUNT[15:8] ≤ 65535
0x00: default value
8.6.25 Register LHR_OFFSET_LSB (address = 0x32) [reset = 0x00]
Figure 37. Register LHR_OFFSET_LSB
7
6
5
4
3
2
1
0
LHR_OFFSET[7:0]
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 27. Register LHR_OFFSET_LSB Field Descriptions
Bit
Field
Type
Reset
Description
High Resolution L-Measurement Offset Setting
Combine with value in Register LHR_OFFSET_LSB (Address
7:0
LHR_OFFSET[7:0]
R/W
0x32) to set the offset value applied to High Resolution
L
Measurements.
0x00: default value
8.6.26 Register LHR_OFFSET_MSB (address = 0x33) [reset = 0x00]
Figure 38. Register LHR_OFFSET_MSB
7
6
5
4
3
2
1
0
LHR_OFFSET[15:8]
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Copyright © 2015, Texas Instruments Incorporated
25
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Table 28. Register LHR_OFFSET_MSB Field Descriptions
Bit
Field
Type
Reset
Description
7:0
LHR_OFFSET[15:8]
R/W
High Resolution L-Measurement Offset Setting
Combine with value in Register LHR_OFFSET_LSB (Address
0x32) to set the offset value applied to High Resolution
L
Measurements.
0x00: default value
8.6.27 Register LHR_CONFIG (address = 0x34) [reset = 0x00]
Figure 39. Register LHR_CONFIG
7
6
5
4
3
2
1
0
RESERVED
R/W
SENSOR_DIV
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 29. Register LHR_CONFIG Field Descriptions
Bit
Field
Type
Reset
Description
7:2
RESERVED
R/W
Reserved.
Set to b00’0000
1:0
SENSOR_DIV
R/W
Sensor Clock Divider Setting
Divide the sensor frequency by programmed divider. This divider
can be used to set the sensor frequency lower than the reference
frequency. Refer to Sensor Input Divider for more details.
b00: Sensor Frequency not divided (default value)
b01: Sensor Frequency divided by 2
b10: Sensor Frequency divided by 4
b11: Sensor Frequency divided by 8
8.6.28 Register LHR_DATA_LSB (address = 0x38) [reset = 0x00]
Figure 40. Register LHR_DATA_LSB
7
6
5
4
3
2
1
0
LHR_DATA[7:0]
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 30. Register LHR_DATA_LSB Field Descriptions
Bit
Field
Type
Reset
Description
High Resolution L-Measurement Conversion Result
7:0
LHR_DATA[7:0]
R
Combine with values in Registers LHR_DATA_MID (Address 0x39)
and LHR_DATA_MSB (Address 0x3A) to determine conversion
result.
fSENSOR = fCLKIN ˣ SENSOR_DIV ˣ LHR_DATA ÷ 224
NOTE: The LHR_DATA registers must be read in the sequence
0x38 first, then 0x39, and last 0x3A for data coherency.
8.6.29 Register LHR_DATA_MID (address = 0x39) [reset = 0x00]
Figure 41. Register LHR_DATA_MID
7
6
5
4
3
2
1
0
LHR_DATA[15:8]
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
26
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
Table 31. Register LHR_DATA_MID Field Descriptions
Bit
Field
LHR_DATA[15:8]
Type
Reset
Description
7:0
R
High Resolution L-Measurement Conversion Result
Combine with values in Registers LHR_DATA_LSB (Address 0x38)
and LHR_DATA_MSB (Address 0x3A) to determine conversion
result.
NOTE: Register LDR_DATA_LSB must be read prior to this register
and LHR_DATA_MSB to ensure data coherency.
8.6.30 Register LHR_DATA_MSB (address = 0x3A) [reset = 0x00]
Figure 42. Register LHR_DATA_MSB
7
6
5
4
3
2
1
0
LHR_DATA[23:16]
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 32. Register LHR_DATA_MSB Field Descriptions
Bit
Field
Type
Reset
Description
High Resolution L-Measurement Conversion Result
7:0
LHR_DATA[23:16]
R
Combine with values in Registers LHR_DATA_LSB (Address 0x38)
and LHR_DATA_MID (Address 0x39) to determine conversion result.
NOTE: Register LDR_DATA_LSB must be read prior to
LHR_DATA_MID and this register to ensure data coherency.
8.6.31 Register LHR_STATUS (address = 0x3B) [reset = 0x00]
Figure 43. Register LHR_STATUS
7
6
UNUSED
R
5
4
ERR_ZC
R
3
ERR_OR
R
2
ERR_UR
R
1
ERR_OF
R
0
LHR_DRDY
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 33. Register LHR_STATUS Field Descriptions
Bit
7:5
4
Field
Type
R
Reset
Description
UNUSED
ERR_ZC
No Function
R
Zero Count Error
Zero count errors are applicable for LHR measurements and indicate
that no cycles of the sensor occurred in the programmed measurement
interval. This indicates either a sensor error or the sensor frequency is
too low. This field is updated after register 0x38 has been read.
b0: No Zero Count error has occurred for the last LHR conversion result
read.
b1: A Zero Count error has occurred.
3
ERR_OR
R
Conversion Over-range Error
Conversion over-range errors are applicable for LHR measurements and
indicate that the sensor frequency exceeded the reference frequency.
This field is updated after register 0x38 has been read.
b0: No Conversion Over-range error has occurred for the last LHR
conversion result read.
b1: A Conversion Over-range error has occurred.
Copyright © 2015, Texas Instruments Incorporated
27
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Table 33. Register LHR_STATUS Field Descriptions (continued)
Bit
Field
Type
Reset
Description
2
ERR_UR
R
Conversion Under-range Error
Conversion under-range errors are applicable for LHR measurements
and indicate that the output code is negative; this occurs when
programmed LHR offset register value is too large. This field is updated
after register 0x38 has been read.
b0: No Conversion Under-range error has occurred for the last LHR
conversion result read.
b1: A Conversion Under-range error has occurred.
1
0
ERR_OF
R
R
Conversion Over-flow Error
Conversion over-flow errors are applicable for LHR measurements and
indicate that the sensor frequency is too close to the reference
frequency. This field is updated after register 0x38 has been read.
b0: No Conversion Over-flow error has occurred for the last LHR
conversion result read.
b1: A Conversion Over-flow error has occurred.
LHR_DRDY
LHR Data Ready
b0: Unread LHR conversion data is available. This field is set to 0 at the
end of an LHR conversion and remains asserted until a read of register
0x38.
b1: No unread LHR conversion data is available.
8.6.32 Register RID (address = 0x3E) [reset = 0x02]
Figure 44. Register RID
7
6
5
V_ID
R
4
3
2
1
RID
R
0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 34. Register RID Field Descriptions
Bit
Field
Type
Reset
Description
DEVICE ID
7:3
V_ID
R
Returns fixed value indicating device ID.
0x00: indicates LDC1101 (default value)
2:0
RID
R
RID
Returns device RID.
b010: Default value
8.6.33 Register DEVICE_ID (address = 0x3F) [reset = 0xD4]
Figure 45. Register DEVICE_ID
7
6
5
4
3
2
1
0
CHIP_ID
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 35. Register DEVICE_ID Field Descriptions
Bit
Field
Type
Reset
Description
CHIP_ID
7:0
CHIP_ID
R
Returns fixed value indicating device Family ID.
0xD4: indicates LDC1101 family (default value)
28
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
9.1.1 Theory of Operation
An AC current flowing through an inductor will generate an AC magnetic field. If a conductive material, such as a
metal object, is brought into the vicinity of the inductor, the magnetic field will induce a circulating current (eddy
current) on the surface of the conductor. The eddy current is a function of the distance, size, and composition of
the conductor.
Conductive
Target
Eddy
d
Current
Figure 46. Conductor in an AC Magnetic Field
The eddy current generates its own magnetic field, which opposes the original field generated by the inductor.
This effect can be considered as a set of coupled inductors, where the inductor is the primary winding and the
eddy current in the conductor represents the secondary winding. The coupling between the windings is a function
of the inductor, and the resistivity, distance, size, and shape of the conductor.
To minimize the current required to drive the inductor, a parallel capacitor is added to create a resonant circuit,
which will oscillate at a frequency given by Equation 1 when energy is injected into the circuit. In this way, the
LDC1101 only needs to compensate for the parasitic losses in the sensor, represented by the series resistance
RS of the LC tank. The oscillator is then restricted to operating at the resonant frequency of the LC circuit and
injects sufficient energy to compensate for the loss from RS.
L
C
1
¦
2S LC
RS
Figure 47. LC Tank
The resistance and inductance of the secondary winding caused by the eddy current can be modeled as a
distant dependent resistive and inductive component on the primary side (coil). We can then represent the circuit
as an equivalent parallel circuit, as shown in Figure 48.
1
L
RP
C
¦
2S LC
Figure 48. Equivalent Parallel Circuit
The value of RP can be calculated with:
Copyright © 2015, Texas Instruments Incorporated
29
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Application Information (continued)
L
RP =
RsC
where
•
•
•
RS is the AC series resistance at the frequency of operation.
C is the parallel capacitance
L is the inductance
(2)
RP can be viewed as the load on the sensor driver; this load corresponds to the current drive needed to maintain
the oscillation amplitude. The position of a target can change RP by a significant amount, as shown in Figure 49.
The value of RP can then be used to determine the position of a conductive target. If the value of RP is too low,
then the sensor driver will not be able to maintain sufficient oscillation amplitude.
18
16
14
12
10
8
6
4
2
0
0
0.1
0.2
0.3
0.4
0.5
0.6
Target Distance / Sensor Diameter
D010
Figure 49. RP vs Target Distance for a 14 mm Diameter Sensor
9.1.2 RP+L Mode Calculations
For many systems which use the LDC1101, the actual sensor RP, sensor frequency, or sensor inductance is not
necessary to determine the target position; typically the equation of interest is:
PositionTarget = ƒ(RP_DATA) or PositionTarget = ƒ(L_DATA)
where
•
•
RP_DATA is the contents of registers 0x21 and 0x22
L_DATA is the contents of registers 0x23 and 0x24
(3)
These Position equations are typically system dependent. For applications where the Sensor RP in Ωs needs to
be calculated, use Equation 4:
RPMAX ´RPMIN
Rp =
RPDATA
216 -1
RPDATA
216 -1
æ
ö
RPMAX 1-
+ RPMIN
ç
÷
è
ø
where
•
•
•
RPDATA is the contents of RP_DATA_MSB and RP_DATA_LSB (registers 0x21 and 0x22),
RPMIN is the value set by RP_MIN in register RP_SET (register 0x01), and
RPMAX is the value set by RP_MIN in register RP_SET (register 0x01).
(4)
For example, with device settings of:
•
•
RPMIN set to 1.5 kΩ, and
RPMAX set to 12 kΩ.
If RPDATA = 0x33F1 (register 0x21 = 0xF1 and register 0x22= 0x33), which is 13297 decimal, then the sensor
RP = 1.824 kΩ.
30
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
Application Information (continued)
If RPMAX_DIS (Register 0x01-b[7]) is set, then the equation is simply:
RPMIN
Rp =
RPDATA
216 -1
æ
ö
1-
ç
÷
è
ø
(5)
65536
57344
49152
40960
32768
24576
16384
8192
0
0
2.5
5
7.5
10
12.5
15
17.5
20
22.5
25
Sensor RP (k:)
D012
Figure 50. LDC1101 RP Transfer Curve with RPMIN = 1.5 kΩ and RPMAX = 24 kΩ
The sensor frequency in Hz can be calculated from Equation 6:
fCLKIN ´RESP _ TIME
=
fSENSOR
3´L _DATA
where
•
•
•
ƒCLKIN is the frequency input to the CLKIN pin,
L_DATA is the contents of registers 0x23 and 0x24, and
RESP_TIME is the programmed response time in register 0x04.
(6)
The inductance in Henrys can then be determined from Equation 7:
1
LSENSOR
=
2
)
CSENSOR ´ 2pƒ
(
SENSOR
where
•
•
CSENSOR is the fixed sensor capacitance in Farads, and
ƒSENSOR is the measured sensor frequency, as calculated in Equation 6 above.
(7)
Copyright © 2015, Texas Instruments Incorporated
31
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Application Information (continued)
40
38
36
34
32
30
28
26
24
22
20
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
Target Distance / Sensor Diameter
D013
Figure 51. Inductance vs Normalized Target Distance for an Example Sensor
9.1.3 LDC1101 RP Configuration
Setting the RP_MIN and RP_MAX parameters is necessary for proper operation of the LDC1101; the LDC1101
may not be able to effectively drive the sensor with incorrect settings, as the sensor amplitude will be out of the
valid operation region. The LDC1101EVM GUI and the LDC Excel® tools spreadsheet
(http://www.ti.com/lit/zip/slyc137) can be used to calculate these parameters in an efficient manner.
For RP measurements, the following register settings must be set as follows:
•
•
ALT_CONFIG.LOPTIMAL(register 0x05-bit0) = 0
D_CONFIG.DOK_REPORT (register 0x0C-bit0) = 0
1. Ensure that the sensor characteristics are within the Sensor boundary conditions:
(a) 500 kHz < ƒSENSOR < 10 MHz
(b) 100 pF < CSENSOR < 10 nF
(c) 1 µH < LSENSOR < 500 µH
2. Measure the sensor’s resonance impedance with minimal target interaction (RPD∞). The minimal target
interaction occurs when the target is farthest away from the sensor for axial sensing solutions or when the
target coverage of the sensor is at a minimum for rotational or lateral sensing. Select the appropriate setting
for RPMAX (register 0x01-bits [5:4]):
RPD∞ ≤ RPMAX ≤ 2RPD∞
3. Measure the sensor’s resonance impedance with the target closest to the sensor (RPD0) as required by the
application. Select the largest RPMIN setting that satisfies:
(a) RPMIN < 0.8 × RPD0
(b) If the required RPMIN is smaller than 750 Ω, RPD0 must be increased to be compliant with this boundary
condition. This can be done by one or more of the following:
(a) increasing ƒSENSOR
(b) increasing the minimum distance between the target and the sensor
(c) reducing the RS of the sensor by use of a thicker trace or wire
4. Check if the worst-case Sensor quality factor QMIN=RpMIN × √(CSENSOR/LSENSOR) is within LDC1101’s
operating range:
(a) 10 ≤ QMIN ≤ 400
(b) If QMIN < 10, for a fixed ƒSENSOR, increase CSENSOR and decrease LSENSOR
.
(c) If QMIN > 400, for a fixed ƒSENSOR, decrease CSENSOR and increse LSENSOR
.
(d) Alternatively the user may choose to not change the current Sensor parameters, but to increase Rp_D0.
32
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
Application Information (continued)
If the RP of the sensor is greater than 75 kΩ, RP measurement accuracy may be improved by setting
RPMAX_DIS to 1.
9.1.4 Setting Internal Time Constant 1
RP Measurements require configuration of the TC1 and TC2 registers. There are several programmable
capacitance and resistance values. Set Time Constant 1 based on minimum sensor frequency:
2
R1 ´ C1 =
pVAMP ƒSENSOR-MIN
where
•
ƒSENSOR-MIN is the minimum sensor frequency encountered in the system; typically this occurs with no target
present.
•
•
•
VAMP is sensor amplitude of 0.6V,
R1 is the programmed setting for TC1.R1 (register 0x03-bits[4:0]), and
C1 is the programmed setting for TC1.C1 (register 0x03-bits[7:6])
(8)
The acceptable range of R1 is from 20.6 kΩ to 417.4 kΩ. If several combinations of R1 and C1 are possible, it is
recommended to use the largest capacitance setting for C1 that fits the constraints of Equation 8, as this will
provide improved noise performance.
9.1.5 Setting Internal Time Constant 2
Set the Time Constant 2 (register 0x03) using Equation 9:
R2 × C2 = 2 × RP_MIN × CSENSOR
where
•
•
CSENSOR is the parallel capacitance of the sensor.
RP_MIN is the LDC1101 setting determined in LDC1101 RP Configuration (for example, use 1.5 kΩ when
RP_SET.RP_MIN = b110),
•
•
R2 is the programmed setting for TC2.R2 (register 0x03-bits[5:0]), and
C2 is the programmed setting for TC2.C2 (register 0x03-bits[7:6]).
(9)
The acceptable range of R2 is from 24.60 kΩ to 834.8 kΩ. If several combinations of R2 and C2 are possible, it
is recommended to program the larger capacitance setting for C2 that fits the constraints of Equation 9, as this
will provide improved noise performance.
9.1.6 MIN_FREQ and Watchdog Configuration
The LDC1101 includes a watchdog timer which monitors the sensor oscillation. While in active mode, if no
sensor oscillation is detected, the LDC1101 will set STATUS.NO_SENSOR_OSC (register 0x20:bit7), and
attempt to restart the oscillator. This restart will reset any active conversion.
The watchdog waits an interval of time based on the setting of DIG_CONF.MIN_FREQ (register 0x04:bits[7:4]).
The MIN_FREQ setting is also used to configure the startup of oscillation on the sensor. Select the
DIG_CONF.MIN_FREQ (register 0x04-bits[7:4]) setting closest to the minimum sensor frequency; this setting is
used for internal watchdog timing. If the watchdog determines the sensor has stopped oscillating, it will report the
sensor has stopped oscillating in STATUS. NO_SENSOR_OSC (register 0x20-bit7). If the
DIG_CONF.MIN_FREQ is set too low, then the LDC1101 will take a longer time interval to report that the sensor
oscillation has stopped.
If the DIG_CONF.MIN_FREQ is set too high, then the watchdog may incorrectly report that the sensor has
stopped oscillating and attempt to restart the sensor oscillation.
When the watchdog determines that the sensor has stopped oscillating, the LHR conversion results will contain
0xFFFFFF.
Copyright © 2015, Texas Instruments Incorporated
33
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Application Information (continued)
9.1.7 RP+L Sample Rate Configuration with RESP_TIME
The RP+L sample rate can be adjusted by setting by DIG_CONF.RESP_TIME (register 0x04:bits[2:0]). The
Response time can be configured from 192 to 6144 cycles of the sensor frequency. Higher values of Response
time will have a slower sample rate, but produce a higher resolution conversion.
ResponseTime
ConversionTime s =
( )
3´ ƒSENSOR
(10)
9.1.8 High Resolution Inductance Calculation (LHR mode)
For many systems which use the LDC1101, the actual sensor frequency or sensor inductance is not necessary
to determine the target position. Should the sensor frequency in Hz need to be determined, use Equation 11:
2SENSORDIV ´ ƒCLKIN LHRDATA +LHROFFSET ´28
(
)
fSENSOR
=
224
where
•
•
•
•
LHRDATA is the contents of registers 0x38, 0x39, and 0x3A,
LHROFFSET is the programmed contents of registers 0x32 and 0x33,
SENSOR_DIV is the contents of LHR_CONFIG.SENSOR_DIV (register 0x34-bit[1:0]), and
ƒCLKIN is the frequency input to the CLKIN pin: ensure that it is within the specified limits of 1 MHz to 16
MHz.
(11)
Note that LHR_DATA=0x0000000 indicates a fault condition or that the LDC1101 has never completed an LHR
conversion.
The inductance in Henrys can then be determined from the sensor frequency with Equation 12:
1
LSENSOR
=
2
)
CSENSOR ´ 2pƒ
(
SENSOR
where
•
•
CSENSOR is the fixed sensor capacitance, and
ƒSENSOR is the measured sensor frequency, as calculated above.
(12)
Example with the device set to:
•
•
•
LHR_OFFSET = 0x00FF (register 0x32 = 0xFF, and 0x33 = 0x00)
ƒCLKIN = 16 MHz
SENSOR_DIV = b’01 (divide by 2)
and the conversion result is:
LHR_DATA = 0x123456 (register 0x38 = 0x56, register 0x39 = 0x34,register 0x3A = 0x12)
Then entering LHR_DATA = 0x123456 = 1193046 (decimal) into Equation 11:
21 ´16MHz 1193046 +255´28
(
)
fSENSOR
=
224
(13)
Results in ƒSENSOR = 2.400066 MHz.
9.1.9 LHR Sample Rate Configuration with RCOUNT
The conversion time represents the number of reference clock cycles used to measure the sensor frequency.
The LHR mode conversion time is set by the Reference count in LHR_RCOUNT.RCOUNT (registers 0x30 &
0x31). The LHR conversion time is:
55 +RCOUNT ´16
(
)
tCONV
=
ƒCLKIN
(14)
34
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
Application Information (continued)
The 55 is due to post-conversion processing and is a fixed value. The reference count value must be chosen to
support the required number of effective bits (ENOB). For example, if an ENOB of 13 bits is required, then a
minimum conversion time of 213 = 8192 clock cycles is required. 8192 clock cycles correspond to a RCOUNT
value of 0x0200.
Higher values for RCOUNT produce higher resolution conversions; the maximum setting, 0xFFFF, is required for
full resolution.
9.1.10 Setting RPMIN for LHR Measurements
Configure the RP measurement as shown previously for L measurements. If only L measurements are
necessary, then the RP measurement can be disabled by setting:
•
•
ALT_CONFIG.LOPTIMAL(register 0x05-bit0) = 1
D_CONFIG.DOK_REPORT (register 0x0C-bit0) = 1
Setting these bits disable the sensor modulation used by the LDC1101 to measure RP and can reduce L
measurement noise. When the RP modulation is disabled, the LDC1101 will drive a fixed current level into the
sensor. The current drive is configured by RP_SET.RPMIN (address 0x01:bits[2:0]). The sensor amplitude must
remain between 0.25 Vpk and 1.25 Vpk for accurate L measurements. Use Table 36 to determine the
appropriate RPMIN setting, based on the variation in sensor RP. If multiple RPMIN values cover the Sensor RP,
use the higher current drive setting. The equation to determine sensor amplitude is:
p´ Vamp
=
RP
4´IDRIVE
(15)
Table 36. LHR RPMIN Settings when Sensor RP Modulation is Disabled
SENSOR DRIVE
MINIMUM SENSOR
MAXIMUM SENSOR
RPMIN SETTING
RPMIN FIELD VALUE
(μA)
RP (kΩ)
RP (kΩ)
1.65
3.3
0.75 kΩ
1.5 kΩ
3 kΩ
b111
b110
b101
b100
b011
b010
b001
b000
600
300
150
75
0.53
1.1
2.1
6.5
6 kΩ
4.2
13.1
26.2
52.4
105
12 kΩ
24 kΩ
48 kΩ
96 kΩ
37.5
18.7
9.4
8.4
16.9
33.9
67.9
4.7
209
For example, with a sensor that has an RP which can vary between 2.7 kΩ to 5 kΩ, the appropriate setting for
RPMIN would be 3 kΩ (RP_SET.RPMIN = b101). For more information on Sensor RP and sensor drive, refer to
Configuring Inductive-to-Digital-Converters for Parallel Resistance (RP) Variation in L-C Tank
Sensors(SNAA221).
9.1.11 Sensor Input Divider
The reference clock frequency should be greater than 4 times the sensor frequency for optimum measurement
resolution:
ƒCLKIN> 4ƒSENSOR-MAX
For higher sensor frequencies, this relationship may not be realizable without the sensor divider. Set the sensor
divider to an appropriate value to produce an effective reduction in the sensor frequency:
ƒCLKIN> 4ƒSENSOR-MAX ÷ SENSOR_DIV
9.1.12 Reference Clock Input
Use a clean, low jitter, 40-60% duty cycle clock input with an amplitude swing within the range of VDD and GND;
proper clock impedance control, and series or parallel termination is recommended. The rise and fall time should
be less than 5 ns. Do not use a spread-spectrum or modulated clock.
Copyright © 2015, Texas Instruments Incorporated
35
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
For optimum L measurement performance, it is recommended to use the highest reference frequency (16 MHz).
LHR conversions will not start until a clock is provided on CLKIN.
9.1.13 INTB Reporting on SDO
INTB is
a
signal generated by the LDC1101 that reports
a
change in device status. When
INTB_MODE.INTB2SDO=1 (register 0x0A:bit7), INTB is multiplexed onto the SDO pin. Once the reporting is
enabled, select the desired signal to report by setting INTB_MODE.INTB_FUNC (register 0x0A:bit[5:0]).
LDC1101
MCU
CSB
CSB
SCLK
MOSI
MISO
SPI
Peripheral
SCLK
SDI
SDO
INT
Figure 52. SDO/INTB Connection to MCU
For many microcontrollers, the MISO signal on the SPI peripheral cannot provide the desired interrupt
functionality. One method to use the INTB functionality is to connect a second GPIO which triggers on a falling
edge, as shown in Figure 51. Table 37 describes the signal functionality that can be programmed onto INTB.
Table 37. INTB Signal Options
INTB_FUNC
(0x0A:bit[5:0])
SWITCH OUTPUT
TYPE
SIGNAL
FUNCTIONALITY
Indicates new High-Resolution Inductance (LHR) conversion
data is available.
LHR Data Ready (LHR-DRDY)
b10’0000
Latching
L_HI_LO
b01’0000
b00’1000
b00’0100
b00’0010
b00’0001
L Comparator with hysteresis
Hysteresis
Latching
Pulse
L_TH_HI
Latching L High threshold compare
Indicates new RP+L conversion data is available.
RP Comparator with hysteresis
RP+L Data Ready (RPL-DRDY)
RP_HI_LO
Hysteresis
Latching
RP_TH_HI
Latching RP High threshold compare
No INTB reporting – SDO pin only provides SDO
functionality.
None
b00’0000
N/A
CSB
SCK
11
14
1
2
3
4
5
6
7
8
9
10
12 13
15 16
A0
D6
D6
SDI
A6 A5 A4 A3 A2 A1
D7
D7
D5 D4 D3 D2 D1 D0
R
INTB assertion
SDO
D5 D4 D3 D2 D1 D0
Figure 53. Example INTB Signal on SDO
When INTB_MODE.INTB2SDO (register 0x0A:bit7) = 0, the SDO pin is in a Hi-Z state until the 8th falling edge of
SCLK after CSB goes low. When INTB reporting is enabled by setting INTB_MODE.INTB2SDO = 1, after CSB
goes low, the SDO pin will go high and remain high until:
36
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
•
•
•
the event configured by INTB_MODE.INTB_FUNC occurs,
an SPI read transaction is initiated, or
CSB is deasserted (pulled high)
9.1.14 DRDY (Data Ready) Reporting on SDO
Completion of a conversion can be indicated on the SDO pin by reporting the DRDY signal – there is a
conversion complete indicator for the RP+L conversion (RPL-DRDY), and a corresponding conversion complete
indicator for the LHR mode (LHR-DRDY).
When LHR-DRDY or RPL-DRDY is reported on SDO, the SDO pin is asserted on completion of a conversion.
While in this mode, conversion data can be corrupted if a new conversion completes while reading the output
data registers. To avoid data corruption, it is important to retrieve the conversion rates via SPI quicker than the
shortest conversion interval, and to ensure that the data is retrieved before a new conversion could possibly
complete.
When INTB is reporting RPL-DRDY, if CSB is held low for longer than one conversion cycle, INTB will be
deasserted approximately 100 ns to 2 µs prior to the completion of each conversion. The deassertion time is
proportional to 1/ƒSENSOR
.
When INTB is reporting LHR-DRDY, if CSB is held low for longer than one conversion cycle, INTB will assert on
completion of the first conversion and remain low – and it will remain asserted until cleared. To clear the
LHR_DRDY signal, read the LHR_DATA registers.
CSB
INTB assertion
RP+L DRDY
INTB assertion
RP+L DRDY
INTB assertion
RP+L DRDY
SDO
High-Z
High-Z
n-1 interval
RP+L Conversion n interval
RP+L Conversion n+1 interval
RP+L Conversion n+2 interval
LHR Conversion m interval
LHR Conversion m+1 interval
m-1 interval
Figure 54. Reporting RPL-DRDY on INTB/SDO
CSB
SDO
INTB assertion
LHR-DRDY
High-Z
n-1 interval
m-1 interval
High-Z
RP+L Conversion n+2 interval
LHR Conversion m+1 interval
RP+L Conversion n interval
RP+L Conversion n+1 interval
LHR Conversion m interval
Figure 55. Reporting LHR-DRDY on INTB/SDO
Note that the conversion interval for an LHR measurement is asynchronous to the conversion interval for an
RP+L measurement, therefore the LHR-DRDY signal cannot be used to determine when to read RP+L conversion
results, and vice versa.
9.1.15 Comparator Functionality
The LDC1101 provides comparator functionality, in which the RP+L conversion results can be compared against
two thresholds. The results of each RP and L conversion can be compared against programmable thresholds and
reported in the STATUS register. Note that the LHR conversion results cannot be used for comparator
functionality.
Copyright © 2015, Texas Instruments Incorporated
37
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
In addition, the INTB signal can be asserted or deasserted when the conversion results increase above a
Threshold High or decreases below a Threshold Low registers. In this mode, the LDC1101 essentially behaves
as a proximity switch with programmable hysteresis. The threshold HI settings must be programmed to a higher
value than the threshold LO registers (for example, if RP_THRESH_LO is set to 0x2000, RP_THRESH_HI
should programmed to 0x2001 or higher).
Either Latching and non-latching functions can be reported on INTB/SDO. The INTB signal can report a latching
signal or a continuous comparison for each conversion result.
The Threshold setting registers (address 0x06:0x09 and 0x16:0x19) can be changed while the LDC1101 is in
active conversion mode. It is recommended to change the register values using an extended SPI transaction as
described in SPI Programming, so that the register updates can be completed in a shorter time interval. This
functionality enables the LDC1101 to operate as a dynamic tracking switch. LDC1101 output codes can be
readout in < 4 μs, and the set of active thresholds can be updated in <6 μs. It is not recommended to update the
threshold registers more often than once per conversion interval of the LDC1101 (that is, do not change the
threshold register values multiple times in a single conversion interval).
To clear a latched INTB signal, set INTB_MODE = 0x80; it is not necessary for the LDC1101 to be in Sleep
mode to clear the latched output; the INTB_MODE can be changed while the LDC1101 is in active mode. After
clearing the latched output, re-enabling the INTB_FUNC can be done while in active mode.
Table 38. Comparator Options
STATUS
REPORTING
FUNCTION
THRESHOLD HIGH
THRESHOLD LOW
INTB/SDO REPORTING
RP_THRESH_HI
(registers 0x06 & 0x07) (registers 0x08 & 0x09)
RP_THRESH_LO
RP_HI_LON
(bit 4)
RP_HI_LO
(INTB_MODE:INTB_FUNC=b00’0010)
RP Comparator with hysteresis
RP_TH_HI
(INTB_MODE:INTB_FUNC=b00’0001)
RP_THRESH_HI
N/A
RP_HIN
(bit 5)
RP High threshold only (Latching)
L Comparator with hysteresis
(registers 0x06 & 0x07)
Note that INTB/SDO will latch.
L_THRESH_HI
(registers 0x16 & 0x17) (registers 0x18 & 0x19)
L_THRESH_LO
L_HI_LON
(bit 2)
L_HI_LO
(INTB_MODE:INTB_FUNC=b01’0000)
L_TH_HI
L_THRESH_HI
N/A
L High threshold compare only
(Latching)
(INTB_MODE:INTB_FUNC=b00’1000)
L_HIN (bit 3)
(registers 0x18 & 0x19)
Note that INTB/SDO will latch.
space
RP_THRESH_HI
RP_THRESH_HI
RP_DATA
RP_DATA
RP_THRESH_LO
INTB (SDO)
And
RP_HIN
INTB (SDO)
And
RP_HI_LON
Latch Clear
Figure 56. INTB/SDO Output Value for RP Comparator with
Hysteresis (INTB_FUNC=b00’0010)
Figure 57. INTB/SDO Output for RP Threshold High
(INTB_FUNC=b00’00011)
38
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
9.2 Typical Application
Implementation of a system using the LDC1101 first requires determining the appropriate measurement to
perform. Refer to http://e2e.ti.com/blogs_/b/analogwire/archive/2015/02/11/inductive-sensing-should-i-measure-l-
rp-or-both for guidance.
For systems that require measurement of RP, set the following:
•
•
Configure RP settings as instructed in LDC1101 RP Configuration .
Set the internal time constants as detailed in Setting Internal Time Constant 1 and Setting Internal Time
Constant 2.
1.8 V
VDD
LDC1101
CLKIN
Sensor
5.47 µH || 270 pF
RP + L
Meas
Registers
+ Logic
INA
Sensor
Driver
INB
CSB
SCLK
SDI
High Res
L Meas
SPI
MCU
SDO
GND
Figure 58. Example LDC1101 Typical Application
9.2.1 Design Requirements
Example of an axial measurement implementation using the LDC1101. In this example, the sensor is an inductor
constructed of a multi-layer PCB coil in parallel with a C0G grade surface mount capacitor. For this example, a
10 mm diameter Aluminum target of 1mm thickness is moved perpendicular to the plane of the sensor coil.
For this example, the target range of motion is from 1 mm to 3 mm distance from the sensor coil. The position of
the target needs to be reported at a sample rate of 3 ksps. The PCB is a 4-layer construction with 0.1 mm (4
mils) minimum feature size.
9.2.2 Detailed Design Procedure
9.2.2.1 Device Configuration for RP+L Measurement with an Example Sensor
The sensor described in Table 39 meets the restrictions on size on construction. To use it for RP+L measurement
of a 10 mm diameter 1 mm thick Aluminum target moving axially with respect to the sensor:
Copyright © 2015, Texas Instruments Incorporated
39
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Table 39. Example Sensor Characteristics
STRONGEST TARGET
PARAMETER
MINIMUM TARGET INTERACTION
INTERACTION
Inductance
5.47 µH
5.15 µH
Inductor Outer Diameter
Number of Turns
Trace Spacing/ Trace Width
Number of Layers/Separation
Sensor Capacitance
Sensor Frequency
RS
10 mm
17
0.1 mm / 0.16 mm
2 / 0.355 mm
270 pF
4.11 MHz
4.27 MHz
3.23 Ω at 4.27 MHz
5.91 kΩ at 4.27 MHz
42
3.20 Ω at 2.93 MHz
6.33 kΩ at 2.93 MHz
45
RP
Q at 2.9 MHz
This sensor is within the LDC1101 sensor boundary conditions for frequency, Q, and RP. The first step is to
determine the appropriate RPMIN/RPMAX and TC1/2 settings.
1. Setting RPMAX has the constraint of RPD∞ ≤ RpMAX ≤ 2RPD∞
6.11 kΩ ≤ RPMAX ≤ 12.22 kΩ → Set RPMAX to 12 kΩ
2. RPMIN setting using the constraint of RpMIN < 0.8 × RPD0
:
0.8 × 3.20 kΩ = 2.6 kΩ → Set RPMIN to 1.5 kΩ. Therefore, set RPMIN = 1.5 kΩ.
3. Q Range: In step 4, the sensor Q range of 42 to 45 is within the operating range of 10 to 400. As the sensor
Q value is below 50, it is not necessary to use RPMAX_DIS, and so RPMAX_DIS=0.
4. Now set the Time Constant 1 using Equation 8:
R1 × C1 = 0.75026 ÷ 4.11 MHz = 1.8255E-7s
Starting with the largest C1 value of 6 pF for best noise performance results in R1 = 30.5 kΩ.
This is within the R1 range of 20.6 kΩ to 417.4 kΩ, and so C1 = 6 pF can be used.
Picking the next higher programmable value for R1 → Set R1 = 33.9 kΩ.
5. Next, set the Time Constant 2 using Equation 9:
R2 × C2 = 2 × 1.5 kΩ × 270 pF = 8.100E-7s
Starting with the largest C2 value of 24 pF (once again, for best noise performance) results in
R2 = 33.75 kΩ.
This is within the programmable R2 value of 24.60 kΩ to 834.8 kΩ, and so 24 pF can be used for C2.
Picking the next higher programmable value for R2 → Set R2 = 43.3 kΩ.
6. Then configure the MIN_FREQ field. The sensor minimum frequency is 4.11 MHz, which occurs with the
minimum target interaction. Therefore, MIN_FREQ is set to 14, which configures the watchdog for 4.0 MHz.
7. Next, set the response time. Setting 6144 will provide the highest resolution RP measurement with this
sensor. With 6144 the sample rate will be at least 2.01 kSPS. To attain highest resolution with a sample rate
of >3 kSPS, the response time setting should be 3072.
8. All other device settings can be in their default values.
Table 40. LDC1101 Register Settings for RP+L Example Application
FIELD
RPMAX_DIS
RPMAX
RPMIN
C1
FIELD SETTING
disabled
12.0 kΩ
1.5 kΩ
FIELD VALUE
b0
REGISTER
REGISTER VALUE
b011
RP_SET (0x01)
0x36
b110
6 pF
b11
TC1 (0x02)
TC2 (0x03)
0xDE
0xFE
R1
33.9 kΩ
24 pF
b1’1110
b11
C2
R2
43.3 kΩ
b11’1110
40
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
Table 40. LDC1101 Register Settings for RP+L Example Application (continued)
FIELD
FIELD SETTING
4.0 MHz
3072
FIELD VALUE
b1110
REGISTER
REGISTER VALUE
MIN_FREQ
RESP_TIME
FUNC_MODE
DIG_CONF (0x04)
START_CONFIG (0x0B)
0xE6
0x00
b110
active
b00
On power-up, the LDC1101 enters Sleep mode, which is a low power mode used to configure the LDC. If the
LDC1101 is actively converting, write 0x01 to START_CONFIG (address 0x0B) to stop conversions before
writing the settings above.
Once the LDC1101 is configured, the process to retrieve RP+L conversion results is:
1. Set the LDC1101 into conversion mode (active mode) by writing 0x00 to START_CONFIG (register 0x0B).
2. Poll STATUS.DRDYB (register 0x20:bit6) until it indicates a conversion result is present, or use the INTB
signal reporting as described in DRDY (Data Ready) Reporting on SDO.
3. If the desired measurement is RP, then read back registers 0x21 and 0x22. The RP output code is the
contents of register 0x21 + 256 × (contents of register 0x22).
4. If the desired measurement is L, then read back registers 0x23 and 0x24. The L output code is the contents
of register 0x23 + 256 × (contents of register 0x24). Reading both RP and L is permitted, for a more efficient
operation RP and L registers can be retrieved in a single extended SPI transaction as described in SPI
Programming.
5. Process the conversion results on the MCU and repeat from step 2 if additional conversions are desired. If
no additional conversions are required, place the LDC1101 into Sleep mode or Shutdown mode.
9.2.2.2 Device Configuration for LHR Measurement with an Example Sensor
Given a sensor with characteristics as shown in Table 39, the steps to configure the LDC1101 for LHR
measurements are:
1. Determine the device sample rate, based on system requirements, using Equation 14. For this example,
ƒCLKIN = 16 MHz and a sample rate of 3 kSPS is necessary. The number of cycles of the ƒCLKIN that closest
fit the desired sample rate is determined by:
mm 1/(3 kSPS) = 333.3 µs
subtracting the conversion post-processing time of 55 reference clock cycles (55/16 MHz = 3.437 µs):
mm 333.3 µs – 3.437 µs = 329.9 µs → 16 MHz × 163.2 µs = 5278.34 → 5278.34/16 = 329.9
Programming RCOUNT to 330 (0x014A) results in a sample rate of 2.999 kSPS.
2. Next, set the sensor drive. If the sensor was already configured for RP+L measurements with the steps in
Device Configuration for RP+L Measurement with an Example Sensor, then the sensor drive is already
configured and no additional steps are necessary.
3. If the sensor drive needs to be configured, from Table 36, 3 kΩ is the appropriate setting for the sensor RP
range of 6.33 kΩ to 5.61 kΩ.
Table 41. LDC1101 Register Settings for LHR Example Application
FIELD
RPMAX_DIS
RPMAX
FIELD SETTING
disabled
FIELD VALUE
b0
REGISTER
REGISTER VALUE
doesn’t matter
1.5 kΩ
b111
RP_SET (0x01)
0x75
RPMIN
b101
MIN_FREQ
RESP_TIME
4.0 MHz
b1110
b111
DIG_CONF (0x04)
0xE7
don’t care
LHR_RCOUNT_LSB (0x30)
LHR_RCOUNT_MSB (0x31)
START_CONFIG (0x0B)
0x4A
0x01
0x00
RCOUNT
5280
330
b00
FUNC_MODE
active
Copyright © 2015, Texas Instruments Incorporated
41
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
Once the LDC1101 is configured, the process to retrieve LHR conversion results is:
1. Set the LDC1101 into conversion mode (active mode) by writing 0x00 to START_CONFIG (register 0x0B).
2. Poll LHR_STATUS.DRDYB (register 0x3B:bit0) until it indicates a conversion result is present, or use the
INTB signal reporting as described in DRDY (Data Ready) Reporting on SDO.
3. Read back registers 0x38, 0x39, and 0x3A. These registers can be retrieved in a single extended SPI
transaction as described in SPI Programming.
4. Process the conversion results on the MCU and repeat from step 2 if additional conversions are desired. If
no additional conversions are required, place the LDC1101 into Sleep mode or Shutdown mode.
Both sets of conversion results can be retrieved when the conversions complete. Note that the RP+L
conversions will not complete at the same time as LHR conversions.
9.2.3 Application Curves
The RCOUNT = 0x00FF curve, which corresponds to a sample rate of 3.87 ksps, will measure the target position
with a slightly lower resolution than the RCOUNT = 0x014A used in this example. Over the target movement
range of 3 mm, which corresponds to the normalized value of 0.3 on the Axial Measurement graph, the target
position can be resolved to 4 µm.
10
RCOUNT = 0xFFFF
RCOUNT = 0x0FFF
9
RCOUNT = 0x00FF
8
7
6
5
4
3
2
1
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Target Distance / Sensor Diameter
D014
Figure 59. LHR Axial Measurement Resolution vs Normalized Distance for Aluminum Target
42
Copyright © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
7500000
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
7000000
6500000
6000000
5500000
5000000
4500000
4000000
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Target Distance / Sensor Diameter
D015
Figure 60. LHR Output Code vs Normalized Distance for Aluminum Target
Copyright © 2015, Texas Instruments Incorporated
43
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
10 Power Supply Recommendations
A parallel set of 1 µF and 0.1 µF capacitors should be used to bypass VDD, although it may be necessary to
include a larger capacitor with systems which have a larger amount of supply variation. The smallest value
capacitor should be placed as close as possible to the VDD pin. A ground plane is recommended to connect
both the ground and the Die Attach Pad (DAP).
CLDO capacitor should be nonpolarized and have an equivalent series resistance (ESR) less than 1 Ω, with a
SRF of at least 24 MHz.
11 Layout
11.1 Layout Guidelines
The LDC1101 requires minimal external components for effective operation. Following good layout techniques -
providing good grounding and clean supplies are critical for optimum operation. Due to the small physical size of
the LDC1101, use of surface mount 0402 or smaller components can ease routing.
11.1.1 Ground and Power Planes
Ground and power planes are helpful for maintaining a clean supply to the LDC1101. In the layout shown in
Figure 61, a top-layer ground fill is also used for improved grounding.
11.1.2 CLKIN Routing
The CLKIN pin routing should maintain consistent impedance; typically this is 50Ω, but can be adjusted based on
board geometries. If a parallel termination resistor is used, it should be placed as close as possible to the CLKIN
pin. Minimize layer changes and routing through vias for the CLKIN signal. Maintain an uninterrupted ground
plane under the trace.
11.1.3 Capacitor Placement
The capacitor CLDO should be placed as close as possible to the CLDO pin.
Place the bypass capacitors as close as possible to the VDD pin, with the smaller valued capacitor placed closer.
11.1.4 Sensor Connections
The sensor capacitor should be as close as possible to the sensor inductor. The INA and INB traces should be
routed in parallel and as close as possible to each other to minimize coupling of noise. If cable is to be used,
then INA and INB should be a twisted pair or in coaxial cable. The distance between the INA/INB pins and the
sensor will affect the maximum possible sensor frequency. For some applications, it may be helpful to place
small value capacitor (for example, 10 pF) from INA to ground and INB to ground; these capacitors should be
located close to the INA and INB pins.
Refer to Application Note LDC Sensor Design (SNOA930) for additional information on sensor design.
44
版权 © 2015, Texas Instruments Incorporated
LDC1101
www.ti.com.cn
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
11.2 Layout Example
Figure 61. Layout Recommendations
版权 © 2015, Texas Instruments Incorporated
45
LDC1101
ZHCSDS7A –MAY 2015–REVISED JUNE 2015
www.ti.com.cn
12 器件和文档支持
12.1 器件支持
12.1.1 开发支持
要获取在线 LDC 系统设计工具,请访问德州仪器的 Webench® 工具
LDC 计算器工具提供了一系列在 MS Excel® 下运行的计算工具,这些工具对于 LDC 的系统开发非常有用。
12.2 文档支持
12.2.1 相关文档
有关 LDC 传感器设计的详细信息,请参见《LDC 传感器设计应用报告》(文献编号:SNOA930)。
有关使用 LDC 进行横向位置感测(其中目标点移动时与传感器保持一定高度的距离,然后测量偏差)的详细信
息,请参见《LDC1612/LDC1614 线性位置感测》(文献编号:SNOA931)。 LDC1101 LHR 模式的功能相当于
单通道 LDC1612/LDC1614。
有关温度补偿的信息,请参见《LDC1000 温度补偿》(文献编号:SNAA212)。
12.3 社区资源
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 商标
E2E is a trademark of Texas Instruments.
Webench is a registered trademark of Texas Instruments.
Excel is a registered trademark of Microsoft Corporation.
SPI is a trademark of Motorola.
All other trademarks are the property of their respective owners.
12.5 静电放电警告
这些装置包含有限的内置 ESD 保护。 存储或装卸时,应将导线一起截短或将装置放置于导电泡棉中,以防止 MOS 门极遭受静电损
伤。
12.6 术语表
SLYZ022 — TI 术语表。
这份术语表列出并解释术语、首字母缩略词和定义。
13 机械、封装和可订购信息
以下页中包括机械、封装和可订购信息。 这些信息是针对指定器件可提供的最新数据。 这些数据会在无通知且不
对本文档进行修订的情况下发生改变。 欲获得该数据表的浏览器版本,请查阅左侧的导航栏。
46
版权 © 2015, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LDC1101DRCR
LDC1101DRCT
ACTIVE
ACTIVE
VSON
VSON
DRC
DRC
10
10
3000 RoHS & Green
250 RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 125
-40 to 125
L1101
L1101
NIPDAU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
20-Apr-2023
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LDC1101DRCR
LDC1101DRCT
VSON
VSON
DRC
DRC
10
10
3000
250
330.0
180.0
12.4
12.4
3.3
3.3
3.3
3.3
1.1
1.1
8.0
8.0
12.0
12.0
Q2
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
20-Apr-2023
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LDC1101DRCR
LDC1101DRCT
VSON
VSON
DRC
DRC
10
10
3000
250
346.0
210.0
346.0
185.0
33.0
35.0
Pack Materials-Page 2
GENERIC PACKAGE VIEW
DRC 10
3 x 3, 0.5 mm pitch
VSON - 1 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
This image is a representation of the package family, actual package may vary.
Refer to the product data sheet for package details.
4226193/A
www.ti.com
PACKAGE OUTLINE
DRC0010J
VSON - 1 mm max height
SCALE 4.000
PLASTIC SMALL OUTLINE - NO LEAD
3.1
2.9
B
A
PIN 1 INDEX AREA
3.1
2.9
1.0
0.8
C
SEATING PLANE
0.08 C
0.05
0.00
1.65 0.1
2X (0.5)
(0.2) TYP
EXPOSED
THERMAL PAD
4X (0.25)
5
6
2X
2
11
SYMM
2.4 0.1
10
1
8X 0.5
0.30
0.18
10X
SYMM
PIN 1 ID
0.1
C A B
C
(OPTIONAL)
0.05
0.5
0.3
10X
4218878/B 07/2018
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for optimal thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
DRC0010J
VSON - 1 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
(1.65)
(0.5)
10X (0.6)
1
10
10X (0.24)
11
(2.4)
(3.4)
SYMM
(0.95)
8X (0.5)
6
5
(R0.05) TYP
(
0.2) VIA
TYP
(0.25)
(0.575)
SYMM
(2.8)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:20X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
EXPOSED METAL
EXPOSED METAL
SOLDER MASK
OPENING
METAL
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
NON SOLDER MASK
SOLDER MASK
DEFINED
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4218878/B 07/2018
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
DRC0010J
VSON - 1 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
2X (1.5)
(0.5)
SYMM
EXPOSED METAL
TYP
11
10X (0.6)
1
10
(1.53)
10X (0.24)
2X
(1.06)
SYMM
(0.63)
8X (0.5)
6
5
(R0.05) TYP
4X (0.34)
4X (0.25)
(2.8)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
EXPOSED PAD 11:
80% PRINTED SOLDER COVERAGE BY AREA
SCALE:25X
4218878/B 07/2018
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023,德州仪器 (TI) 公司
相关型号:
LDC1300
Electric Fuse, Time Delay Blow, 1300A, 600VAC, 600VDC, 200000A (IR), Inline/holder,
LITTELFUSE
©2020 ICPDF网 联系我们和版权申明