CC2567-PAN1327 [TI]
ANT Bluetooth® Single-Chip, Dual-Mode Module; ANT Bluetooth®单芯片，双模模块
| 型号： | CC2567-PAN1327 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | ANT Bluetooth® Single-Chip, Dual-Mode Module |
| 文件： | 总2页 (文件大小：34K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
CC2567-PAN1327
CC2567-PAN1317
www.ti.com
SWRS099B –DECEMBER 2010–REVISED JANUARY 2011
ANT + Bluetooth® Single-Chip, Dual-Mode Module
1
FEATURES
DESCRIPTION
2
•
Fully Qualified Bluetooth v2.1 + Enhanced
Data Rate (EDR)
The following product brief applies to Panasonic’s
Bluetooth module, series number: PAN1327 and
PAN1317. The Bluetooth chip used is the CC2567
from Texas Instruments.
•
•
ANT+ capable
Bluetooth and ANT Smart Priority Mechanism
Allows Flexible Coexistence and Simultaneous
Operation
The CC2567-PAN1327/17 is the first dual-mode, ANT
and Bluetooth solution in the market. This solution is
a highly-integrated class 2 HCI module with increased
output power capabilities offered by Panasonic using
TI's CC2567 ANT+ and Bluetooth 2.1 + Enhanced
Data Rate (EDR) dual-mode transceiver. Based on
TI's 7th generation Bluetooth technology, the solution
provides best-in-class Bluetooth RF performance of
+10 dBm typical Tx power and -93 dBm typical
receiver sensitivity. The CC2567-PAN1327/17
module allows customers to connect to mobile
phones and computers over Bluetooth from ANT+
enabled devices, and allows customers with
Bluetooth solutions to add ultra low-power ANT+
connectivity. This solution is provided as a module to
help customers reduce development time, lower
manufacturing costs, save board space, ease
certification, and minimize RF expertise required. For
evaluation and development, a platform is available
that integrates the CC2567-PAN1327/17 module,
Bluetooth stack, Serial Port Profile, ANT+ solution
and sample source applications running on a TI host
controller – MSP430.
•
+10 dBm Typical Tx Power with Transmit
Power Control
•
•
- 93 dBm Typical Receiver Sensitivity
Support for Bluetooth Power Saving Modes
(Sniff, Hold)
•
Low Power Scan Method for Page and Inquiry
Scans at 1/3rd Normal Power
•
•
Fast Algorithm for Both ACL and eSCO
Host Controlled Interface (HCI) Supports Three
and Four Wire UART Transport with Rates of
up to 4Mbps
•
•
Hardware and Software Pre-integration with
TI’s MSP430 Ultra Low-power Microcontroller
Dimensions: 9 mm x 9.5 mm x 1.8 mm
(CC2567-PAN1327, Integrated Antenna);
6.5 mm x 9.5 mm x 1.8 mm
(CC2567-PAN1317, Without Antenna)”
•
•
Bluetooth, FCC, CE, IC Certified
Operating Temperature Range: -20C° to 70°C
The full specification and purchasing of the
CC2567-PAN1327/17 can be found on Panasonic’s
website (www.panasonic.com/ti). The development kit
for this solution is available for order today through
the ANT + Bluetooth Health and Fitness Aggregator
Kit tool folder (www.ti.com/cc2567_pan1327_antbtkit).
More information on TI’s wireless platform solutions
can be found on TI's Wireless Connectivity Wiki
(www.ti.com/connectivitywiki).
APPLICATIONS
•
•
•
•
ANT+ and Bluetooth Aggregators
Sports and fitness devices
Health and wellness devices
Ability to add ultra low-power ANT+
technology to existing Bluetooth solutions
•
Connect current ANT+ applications to mobile
phones and computers via Bluetooth
Disclaimer:
All content in and linked to this product brief is provided by TI "AS IS" without express or implied warranties of
any kind, and it may contain errors, omissions and technical inaccuracies. TI does not endorse or warrant any of
the third party products or services referenced on this product brief. This information is provided subject to TI’s
Terms of Use.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010–2011, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Medical
Security
Logic
Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
RFID
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
Wireless
www.ti.com/video
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明