BQ4013LYMA-70 [TI]
NON-VOLATILE SRAM MODULE;
| 型号： | BQ4013LYMA-70 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | NON-VOLATILE SRAM MODULE 存储 内存集成电路 静态存储器 光电二极管 |
| 文件： | 总15页 (文件大小：165K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
bq4013/Y/LY
www.ti.com
SLUS121A–MAY 1999–REVISED MAY 2007
128 k × 8 NONVOLATILE SRAM (5 V, 3.3 V)
FEATURES
GENERAL DESCRIPTION
•
•
•
•
Data Retention for at least 10 Years Without
Power
The CMOS bq4013/Y/LY is
a
nonvolatile
1,048,576-bit static RAM organized as 131,072
words by 8 bits. The integral control circuitry and
lithium energy source provide reliable nonvolatility
coupled with the unlimited write cycles of standard
SRAM.
Automatic Write-Protection During
Power-up/Power-down Cycles
Conventional SRAM Operation, Including
Unlimited Write Cycles
The control circuitry constantly monitors the single
supply for an out-of-tolerance condition. When VCC
falls out of tolerance, the SRAM is unconditionally
write-protected to prevent an inadvertent write
operation.
Internal Isolation of Battery before Power
Application
•
•
5-V or 3.3-V Operation
Industry Standard 32-Pin DIP Pinout
At this time the integral energy source is switched on
to sustain the memory until after VCC returns valid.
The bq4013/Y/LY uses extremely low standby
current CMOS SRAMs, coupled with small lithium
coin cells to provide nonvolatility without long
write-cycle times and the write-cycle limitations
associated with EEPROM.
The bq4013/Y/LY requires no external circuitry and is
compatible with the industry-standard 1-Mb SRAM
pinout.
PIN CONNECTIONS
32−Pin DIP Module
(TOP VIEW)
NC
1
2
3
4
5
6
7
8
9
32
31
30
29
28
27
26
25
24
V
A
NC
CC
A
16
15
A
14
A
12
WE
A
7
A
13
A
6
A
8
A
5
A
9
A
4
A
11
A
3
OE
A
10
11
12
13
14
15
16
23
22
21
20
19
18
17
A
2
10
A
1
CE
DQ
A
0
7
DQ
DQ
DQ
DQ
DQ
0
6
5
4
3
DQ
1
DQ
2
V
SS
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2007, Texas Instruments Incorporated
bq4013/Y/LY
www.ti.com
SLUS121A–MAY 1999–REVISED MAY 2007
DEVICE INFORMATION
Table 1. TERMINAL FUNCTIONS
TERMINAL
I/O
DESCRIPTION
NAME
A0
NUMBER
12
11
10
9
I
A1
I
A2
I
A3
I
A4
8
I
A5
7
I
A6
6
I
A7
5
I
A8
27
26
23
25
4
I
Address inputs
A9
I
A10
A11
A12
A13
A14
A15
A16
CE
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
I
I
I
28
3
I
I
I
31
2
I
22
13
14
15
17
18
19
20
21
1
I
Chip-enable input
Data input/output
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
-
NC
No connect
30
24
32
16
29
-
OE
I
Output enable input
Supply voltage input
Ground
VCC
VSS
WE
I
-
I
Write enable input
FUNCTIONAL DESCRIPTION
When power is valid, the bq4013/Y/LY operates as a standard CMOS SRAM. During power-down and power-up
cycles, the bq4013/Y/LY acts as a nonvolatile memory, automatically protecting and preserving the memory
contents.
Power-down/power-up control circuitry constantly monitors the VCC supply for a power-fail-detect threshold VPFD
.
The bq4013 monitors for VPFD = 4.62 V typical for use in 5-V systems with 5% supply tolerance. The bq4013Y
monitors for VPFD = 4.37 V typical for use in 5-V systems with 10% supply tolerance. The bq4013LY monitors for
VPFD = 2.90 V (typ) for use in 3.3-V systems.
2
Submit Documentation Feedback
bq4013/Y/LY
www.ti.com
SLUS121A–MAY 1999–REVISED MAY 2007
When VCC falls below the VPFD threshold, the SRAM automatically write-protects the data. All outputs become
high impedance, and all inputs are treated as don't care. If a valid access is in process at the time of power-fail
detection, the memory cycle continues to completion. If the memory cycle fails to terminate within time tWPT
write-protection takes place.
,
As VCC falls past VPFD and approaches VSO, the control circuitry switches to the internal lithium backup supply,
which provides data retention until valid VCC is applied.
When VCC returns to a level above the internal backup cell voltage, the supply is switched back to VCC. After VCC
ramps above the VPFD threshold, write-protection continues for a time tCER (120 ms maximum in 5-V system, 85
ms maximum in 3.3-V system) to allow for processor stabilization. Normal memory operation may resume after
this time.
The internal coin cells used by the bq4013/Y/LY have an extremely long shelf life and provide data retention for
more than 10 years in the absence of system power.
As shipped from TI, the integral lithium cells of the MT-type module are electrically isolated from the memory.
(Self-discharge in this condition is approximately 0.5% per year.) Following the first application of VCC, this
isolation is broken, and the lithium backup provides data retention on subsequent power-downs.
BLOCK DIAGRAM
DIP MODULE
bq4013/Y/LY
MA PACKAGE
OE
A
- A
16
0
128 k × 8
SRAM
Block
WE
DQ - DQ
0
7
Power
CE
CON
CE
V
Power-Fail
Control
CC
Lithium
Cell
+
UDG-06075
TRUTH TABLE
MODE
Not selected
Output disable
Read
CE
WE
X
OE
X
I/O OPERATION
High-Z
POWER
Standby
Active
H
L
L
L
H
H
High-Z
H
L
DOUT
Active
Write
L
X
DIN
Active
3
Submit Documentation Feedback
bq4013/Y/LY
www.ti.com
SLUS121A–MAY 1999–REVISED MAY 2007
ORDERING INFORMATION
For the most current package and ordering information, see the Package Option Addendum at the end of the datasheet, or see
the TI website at www.ti.com.
SELECTION GUIDE
MAXIMUM
ACCESS
TIME (ns)
NEGATIVE SUPPLY
TOLERANCE
(%)
NOMINAL INPUT
VOLTAGE
TEMPERATURE
DEVICE NUMBER
(°C)
VCC (V)
bq4013MA-85
85
120
70
-5
bq4013MA-120
bq4013YMA-70
bq4013YMA-85
bq4013YMA-120
bq4013YMA-70N
bq4013YMA-85N
bq4013LYMA-70N
0 to 70
85
5
120
70
-10
85
-40 to 85
70
3.3
PART NUMBERING
INPUT
VOLTAGE
(V)
NEGATIVE
SUPPLY
TOLERANCE
PRODUCT
LINE
MEMORY
DENSITY
SPEED
(ns)
TEMPERATURE
PACKAGE
(°C)
bq40
13
L
Y
MA
70
70
N
10 = 8 k × 8
Blank = 5
L= 3.3
Blank = 5%
Y = 10%
MA = DIP
Blank = Commercial
( 0 to 70)
11 = 32 k × 8
13 = 128 k × 8
14 = 256 k × 8
15 = 512 k × 8
16 = 1024 k × 8
17 = 2048 k × 8
85
100
120
150
200
N = Industrial
(-40 to 85)
4
Submit Documentation Feedback
bq4013/Y/LY
www.ti.com
SLUS121A–MAY 1999–REVISED MAY 2007
ABSOLUTE MAXIMUM RATINGS(1)
PARAMETER
CONDITION
VALUE
–0.3 to 7.0
–0.3 to 7.0
–0.3 to 6.0
–0.3 to 7.0
–0.3 to 7.0
–0.3 to (VCC + 0.3)
0 to 70
UNIT
bq4013Y
bq4013
VCC
DC voltage applied on VCC relative to VSS
V
bq4013LY
bq4013Y
bq4013
DC voltage applied on any pin excluding
VCC relative to VSS
VT
V
VT≤ VCC +0.3 V
V
bq4013LY
Commercial
Industrial
TOPR
Operating temperature
Storage temperature
–40 to 85
–10 to 70
–40 to 85
–10 to 70
–40 to 85
260
Commercial
Industrial
TSTG
°C
Commercial
Industrial
TBIAS
Temperature under bias
Soldering temperature
TSOLDER
For 10 seconds
(1) Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation should be limited to the
Recommended DC Operating Conditions detailed in this data sheet. Exposure to conditions beyond the operational limits for extended
periods of time may affect device reliability.
RECOMMENDED OPERATING CONDITIONS (TA = TOPR
)
MIN TYP(1)
MAX UNIT
5.50
bq4013Y
bq4013
4.50
4.75
3.00
0
5.00
5.00
3.30
0
VCC
Supply voltage
5.50
bq4013LY
3.60
V
VSS
VIL
Supply voltage
0
Low-level input voltage
High-level Input voltage
–0.3
2.2
0.8
VIH
VCC + 0.3
(1) Typical values indicate operation at TA = 25°C.
DC ELECTRICAL CHARACTERISTICS
TA = TOPR, VCC(min)≤ VCC≤ VCC(max)
PARAMETER
TEST CONDITIONS
VIN = VSS to VCC
MIN TYP(1)
MAX
UNIT
ILI
Input leakage current
Output leakage current
Output high voltage
Output low voltage
±1
±1
µA
ILO
CE = VIH or OE = VIH or WE = VIL
IOH = –1.0 mA
VOH
VOL
ISB1
2.4
V
IOL = 2.1 mA
0.4
2
Standby supply current
CE = VIH
1
µA
CE≥ VCC– 0.2 V, 0V ≤ VIN≤ 0.2 V,
or VIN≥ VCC– 0.2
ISB2
Standby supply current
Operating supply current
0.1
1
mA
bq4013
bq4013Y
bq4013LY
bq4013
50
Minimum cycle, duty = 100%,
CE = VIL, II/O = 0 mA
ICC
mA
50
4.75
4.50
2.95
4.55
4.30
2.85
4.62
4.37
2.90
3
VPFD
Power-fail-detect voltage
Supply switch-over voltage
bq4013Y
bq4013LY
bq4013
V
VSO
bq4013Y
bq4013LY
3
2.9
(1) Typical values indicate operation at TA = 25°C, VCC = 5.0 V or VCC = 3.3 V.
5
Submit Documentation Feedback
bq4013/Y/LY
www.ti.com
SLUS121A–MAY 1999–REVISED MAY 2007
CAPACITANCE (TA = 25°C, f = 1 MHz, VCC = 5.0 V or VCC = 3.3 V)
PARAMETER(1)
Input/output capacitance
Input capacitance
TEST CONDITIONS
Output voltage = 0 V
Input voltage = 0 V
MIN
TYP
MAX
UNIT
pF
CI/O
CIN
8
10
(1) Ensured by design. Not production tested.
AC TEST CONDITIONS
PARAMETER
TEST CONDITIONS
5 V
3.3 V
Input pulse levels
0 V to 3.0 V
5 ns
0 V to VCC
5 ns
Input rise and fall times
Input and output timing reference levels
Output load (including scope and jig)
1.5 V (unless otherwise specified)
See Figure 1 and Figure 2
50 %
See Figure 3 and Figure 4
+ 5 V
+ 5 V
1.9 kW
1.9 kW
D
D
OUT
OUT
1 kW
100 pF
1 kW
5 pF
Figure 1. 5-V Output Load A
Figure 2. 5-V Output Load B
+ 3.3 V
+ 3.3 V
1.2 kW
1.2 kW
D
D
OUT
OUT
1.4 kW
30 pF
1.4 kW
5 pF
Figure 3. 3.3-V Output Load A
Figure 4. 3.3-V Output Load B
6
Submit Documentation Feedback
bq4013/Y/LY
www.ti.com
SLUS121A–MAY 1999–REVISED MAY 2007
Table 2. READ CYCLE (TA = TOPR, VCC(min)≤ VCC≤ VCC(max)
)
-70
MIN
-85
MIN
-120
MIN
PARAMETER
Read cycle time
TEST CONDITIONS
UNIT
MAX
MAX
MAX
tRC
70
85
120
tAA
Address access time
70
70
35
85
85
45
120
120
60
tACE
tOE
Chip enable access time
Output load A
Output enable to output valid
Chip enable to output in low Z
Output enable to output in low Z
Chip disable to output in high Z
Output disable to output in high Z
Output hold from address change
tCLZ
tOLZ
tCHZ
tOHZ
tOH
5
0
5
0
5
0
ns
Output load B
Output load A
0
25
25
0
35
25
0
45
35
0
0
0
10
10
10
t
RC
Address
t
AA
t
OH
D
OUT
Previous Data Valid
Data Valid
(1) WE is held high for a read cycle.
(2) Device is continuously selected: CE = OE = VIL.
Figure 5. Read Cycle No. 1 (Address Access) (1)(2)
t
RC
CE
t
ACE
t
t
CHZ
CLZ
D
OUT
High−Z
High−Z
(1) WE is held high for a read cycle.
(2) Device is continuously selected: CE = OE = VIL.
(3) Address is valid prior to or coincident with CE transition low.
Figure 6. Read Cycle No. 2 (CE Access) (1)(2)(3)
7
Submit Documentation Feedback
bq4013/Y/LY
www.ti.com
SLUS121A–MAY 1999–REVISED MAY 2007
t
RC
Address
OE
t
AA
t
t
OE
OHZ
t
OLZ
D
OUT
Data Valid
High−Z
(1) WE is held high for a read cycle.
(2) Device is continuously selected: CE = VIL.
High−Z
Figure 7. Read Cycle No. 3 (OE Access) (1)(2)
8
Submit Documentation Feedback
bq4013/Y/LY
www.ti.com
SLUS121A–MAY 1999–REVISED MAY 2007
Table 3. WRITE CYCLE (TA = TOPR, VCC(min)≤ VCC≤ VCC(max)
)
-70
-85
-120
MIN MAX
120
PARAMETER
Write cycle time
TEST CONDITIONS
UNIT
MIN MAX
MIN
MAX
tWC
tCW
tAW
70
65
65
85
75
75
(1)
(1)
Chip enable to end of write
Address valid to end of write
See
See
100
100
Measured from address valid to beginning
of write.(2)
tAS
Address setup time
0
55
5
0
65
5
0
85
5
Measured from beginning of write to end of
write. (1)
tWP
Write pulse width
Measured from WE going high to end of
write cycle.(3)
tWR1
tWR2
tDW
tDH1
tDH2
Write recovery time (write cycle 1)
Write recovery time (write cycle 2)
Data valid to end of write
Data hold time (write cycle 1)
Data hold time (write cycle 2)
ns
Measured from CE going high to end of
write cycle.(3)
15
30
0
15
35
0
15
45
0
Measured to first low-to- high transition of
either CE or WE.
Measured from WE going high to end of
write cycle.(4)
Measured from CE going high to end of
write cycle.(4)
0
0
0
tWZ
tOW
Write enbled to output in high Z
Output active from end of write
I/O pins are in output state.(5)
I/O pins are in output state. (5)
0
5
25
0
5
30
0
5
40
(1) A write ends at the earlier transition of CE going high and WE going high.
(2) A write occurs during the overlap of a low CE and a low WE. A write begins at the later transition of CE going low and WE going low.
(3) Either tWR1 or tWR2 must be met.
(4) Either tDH1 or tDH2 must be met.
(5) If CE goes low simultaneously with WE going low or after WE going low, the outputs remain in high-impedance state.
t
WC
Address
t
AW
t
WR1
t
CW
CE
t
AS
t
WP
WE
t
t
DW
DH1
Data−In Valid
D
IN
t
WZ
t
OW
D
OUT
Data Undefined (1)
High−Z
(1) CE or WE must be high during address transition.
(2) Because I/O may be active (OE low) during this period, data input signals of opposite polarity to the outputs must not
be applied.
(3) If OE is high, the I/O pins remain in a state of high impedance.
Figure 8. Write Cycle No. 1 (WE-Controlled) (1)(2)(3)
9
Submit Documentation Feedback
bq4013/Y/LY
www.ti.com
SLUS121A–MAY 1999–REVISED MAY 2007
t
WC
Address
t
AW
t
WR2
t
AS
t
CW
CE
t
WP
WE
t
DW
t
DH2
D
IN
Data−in Valid
t
WZ
D
OUT
Data Undefined (1)
High−Z
(1) CE or WE must be high during address transition.
(2) Because I/O may be active (OE low) during this period, data input signals of opposite polarity to the outputs must not
be applied.
(3) If OE is high, the I/O pins remain in a state of high impedance.
(4) Either tWR1 or tWR2 must be met.
(5) Either tDH1 or tDH2 must be met.
Figure 9. Write Cycle No. 2 (CE-Controlled) (1)(2)(3)(4)(5)
10
Submit Documentation Feedback
bq4013/Y/LY
www.ti.com
SLUS121A–MAY 1999–REVISED MAY 2007
Table 4. 5-V POWER-DOWN/POWER-UP (TA = TOPR
)
PARAMETER
TEST CONDITIONS
MIN TYP(1)
MAX
UNIT
µs
tPF
tFS
tPU
VCC slew, 4.75 to 4.25 V
VCC slew, 4.25 to VSO
300
10
0
µs
VCC slew, VSO to VPFD (max.)
µs
Time during which SRAM is write-protected after
VCC passes VPFD on power-up.
Data-retention time in absence of VCC TA = 25°C(2)
Delay after VCC slews down past VPFD before SRAM
is writeprotected.
tCER
tDR
Chip enable recovery time
40
10
40
80
120
150
ms
years
µs
tWPT
Write-protect time
100
(1) Typical values indicate operation at TA = 25°C, VCC = 5V.
(2) Batteries are disconnected from circuit until after VCC is applied for the first time. tDR is the accumulated time in absence of power
beginning when power is first applied to the device.
t
PF
V
CC
4.75 V
V
PFD
V
PFD
4.25 V
V
V
SO
SO
t
FS
t
PU
t
DR
t
CER
t
WPT
CE
Figure 10. 5-V Power-Down/Power-Up Timing
11
Submit Documentation Feedback
bq4013/Y/LY
www.ti.com
SLUS121A–MAY 1999–REVISED MAY 2007
Table 5. 3.3-V POWER-DOWN/POWER-UP (TA = TOPR
)
PARAMETER
VCC slew, 3 V to 0 V
TEST CONDITIONS
MIN TYP(1)
300
MAX
UNIT
tF
µs
tR
VCC slew, VSO to VPFD (max)
100
Time during which SRAM is write-protected after
VCC passes VPFD on power-up.
Data-retention time in absence of VCC TA = 25°C(2)
tCER
Chip enable recovery time
10
10
85
ms
tDR
years
(1) Typical values indicate operation at TA = 25°C, VCC = 3.3 V.
(2) Batteries are disconnected from circuit until after VCC is applied for the first time. Data retention time (tDR) is the accumulated time in
absence of power beginning when power is first applied to the device.
V
CC
3.0 V
V
PFD(max)
V
PFD
V
SO
V
SO
t
R
t
DR
t
t
F
CER
CE
Figure 11. 3.3-V Power-Down/Power-Up Timing
CAUTION:
Negative undershoots below the absolute maximum rating of -0.3 V in
battery-backup mode may affect data integrity.
12
Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com
9-Oct-2007
PACKAGING INFORMATION
Orderable Device
BQ4013LYMA-70N
BQ4013MA-120
BQ4013MA-85
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
DIP MOD
ULE
MA
32
32
32
32
32
32
32
32
1
1
1
1
1
1
1
1
Pb-Free
(RoHS)
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
DIP MOD
ULE
MA
MA
MA
MA
MA
MA
MA
Pb-Free
(RoHS)
DIP MOD
ULE
Pb-Free
(RoHS)
BQ4013YMA-120
BQ4013YMA-70
BQ4013YMA-70N
BQ4013YMA-85
BQ4013YMA-85N
DIP MOD
ULE
Pb-Free
(RoHS)
DIP MOD
ULE
Pb-Free
(RoHS)
DIP MOD
ULE
Pb-Free
(RoHS)
DIP MOD
ULE
Pb-Free
(RoHS)
DIP MOD
ULE
Pb-Free
(RoHS)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MPDI061 – MAY 2001
MA (R-PDIP-T**)
PLASTIC DUAL-IN-LINE
28 PINS SHOWN
Inches
Max.
Millimeters
Min.
Max.
Dimension
A
Min.
0.365
0.015
0.017
0.008
0.710
1.470
1.670
2.070
0.710
0.590
0.090
0.120
0.105
0.075
0.375
–
9.27
0.38
9.53
–
A1
0.023
0.58
0.33
0.43
B
0.20
C
0.013
0.740
1.500
1.700
2.100
0.740
D/12 PIN
D/28 PIN
D/32 PIN
D/40 PIN
18.03
37.34
42.42
52.58
18.03
18.80
38.10
43.18
53.34
18.80
16.00
2.79
D
E
e
14.99
2.29
0.630
0.110
G
L
3.81
3.05
2.67
1.91
0.150
0.130
0.110
S/12 PIN
S
3.30
2.79
E
L
A
A1
C
B
e
S
G
4201975/A 03/01
NOTES: A. All linear dimensions are in inches (mm).
B. This drawing is subject to change without notice.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Applications
Audio
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/audio
Automotive
Broadband
Digital Control
Military
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
interface.ti.com
logic.ti.com
Logic
Power Mgmt
Microcontrollers
RFID
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lpw
Telephony
Low Power
Wireless
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明