BQ2057TTSTRG4 [TI]
ADVANCED LINEAR CHARGE MANAGEMENT IC FOR SINGLE-AND TWO-CELL LITHIUM-ION AND LITHIUM-POLYMER; 高级线性充电管理IC,适用于单节和两节锂离子和锂聚合物型号: | BQ2057TTSTRG4 |
厂家: | TEXAS INSTRUMENTS |
描述: | ADVANCED LINEAR CHARGE MANAGEMENT IC FOR SINGLE-AND TWO-CELL LITHIUM-ION AND LITHIUM-POLYMER |
文件: | 总30页 (文件大小:1041K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢇ
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
ꢊ
ꢋ
ꢘ
ꢌ
ꢊ
ꢊ
ꢍ
ꢍ
ꢋ
ꢇ
ꢎ
ꢈ
ꢋ
ꢉ
ꢏ
ꢖ
ꢐ
ꢘ
ꢍ
ꢇ
ꢎ
ꢎ
ꢊ
ꢏ
ꢑ
ꢏ
ꢇ
ꢒ
ꢈ
ꢊ
ꢒ
ꢑꢓ ꢎ ꢔ ꢊꢍꢊꢓ ꢎꢔ ꢎꢍꢈ ꢐꢇ
ꢐ ꢙꢔꢘꢐ ꢖ ꢍ ꢊꢍꢋ ꢏ ꢐꢈ ꢒꢐ ꢙꢔꢘꢚ ꢖ ꢏꢛꢔ ꢎꢑ
ꢕ
ꢖ
ꢑ
ꢗ
ꢐ
ꢍ
ꢓ
ꢏ
ꢎ
ꢏ
ꢐ
FEATURES
DESCRIPTION
D
D
D
D
D
Ideal for Single (4.1 V or 4.2 V) and Dual-Cell
(8.2 V or 8.4 V) Li-Ion or Li-Pol Packs
The BENCHMARQ bq2057 series advanced
Lithium-Ion (Li-Ion) and Lithium-Polymer (Li-Pol) linear
charge-management ICs are designed for cost-
sensitive and compact portable electronics. They
combine high-accuracy current and voltage regulation,
battery conditioning, temperature monitoring, charge
termination, charge-status indication, and AutoComp
charge-rate compensation in a single 8-pin IC. MSOP,
TSSOP, and SOIC package options are offered to fit a
wide range of end applications.
Requires Small Number of External
Components
0.3 V Dropout Voltage for Minimizing Heat
Dissipation
Better Than 1% Voltage Regulation Accuracy
With Preset Voltages
AutoCompt Dynamic Compensation of
Battery Pack’s Internal Impedance to Reduce
Charge Time
The bq2057 continuously measures battery
temperature using an external thermistor. For safety,
the bq2057 inhibits charge until the battery temperature
is within user-defined thresholds. The bq2057 then
charges the battery in three phases: conditioning,
constant current, and constant voltage. If the battery
D
D
Optional Cell-Temperature Monitoring Before
and During Charge
Integrated Voltage and Current Regulation
With Programmable Charge-Current and High-
or Low-Side Current Sensing
voltage is below the low-voltage threshold, V
, the
(min)
D
D
Integrated Cell Conditioning for Reviving
Deeply Discharged Cells and Minimizing Heat
Dissipation During Initial Stage Of Charge
bq2057 precharges using a low current to condition the
battery. The conditioning charge rate is approximately
10% of the regulation current. The conditioning current
also minimizes heat dissipation in the external pass-
element during the initial stage of the charge. After
conditioning, the bq2057 applies a constant current to
the battery. An external sense-resistor sets the current.
The sense-resistor can be on either the high or low side
of the battery without additional components. The
constant-current phase continues until the battery
reaches the charge-regulation voltage.
Charge Status Output for Single or Dual Led
or Host Processor Interface
D
D
D
Automatic Battery-Recharge Feature
Charge Termination by Minimum Current
Automatic Low-Power Sleep Mode When V
CC
Is Removed
D
EVMs Available for Quick Evaluation
D
Packaging: 8-Pin SOIC, 8-Pin TSSOP, 8-Pin
MSOP
bq2057xSN or bq2057xTS
SOIC (SN) or TSSOP (TS) PACKAGE
(TOP VIEW)
bq2057xDGK
MSOP (DGK) PACKAGE
(TOP VIEW)
COMP
CC
BAT
SNS
BAT
VCC
TS
8
7
6
5
VCC
TS
8
7
6
5
1
2
3
4
1
2
3
4
SNS
COMP
CC
VSS
STAT
VSS
STAT
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
AutoComp is a trademark of Texas Instruments.
ꢚ
ꢚ
ꢑ
ꢖ
ꢪ
ꢋ
ꢦ
ꢙ
ꢇ
ꢤ
ꢈ
ꢥ
ꢐ
ꢟ
ꢖ
ꢝ
ꢍ
ꢞ
ꢋ
ꢊ
ꢈ
ꢊ
ꢜ
ꢝ
ꢧ
ꢞ
ꢟ
ꢥ
ꢠ
ꢡ
ꢢ
ꢢ
ꢣ
ꢣ
ꢜ
ꢜ
ꢟ
ꢟ
ꢝ
ꢝ
ꢜ
ꢤ
ꢤ
ꢨ
ꢥ
ꢦ
ꢠ
ꢠ
ꢧ
ꢧ
ꢝ
ꢣ
ꢢ
ꢡ
ꢤ
ꢤ
ꢟ
ꢞ
ꢨ
ꢈꢧ
ꢦ
ꢀ
ꢤ
ꢩ
ꢜ
ꢥ
ꢢ
ꢤ
ꢣ
ꢜ
ꢣ
ꢟ
ꢠ
ꢝ
ꢦ
ꢪ
ꢢ
ꢝ
ꢣ
ꢣ
ꢧ
ꢤ
ꢫ
Copyright 2002, Texas Instruments Incorporated
ꢠ
ꢟ
ꢥ
ꢣ
ꢟ
ꢠ
ꢡ
ꢣ
ꢟ
ꢤ
ꢨ
ꢜ
ꢞ
ꢜ
ꢥ
ꢧ
ꢠ
ꢣ
ꢬ
ꢣ
ꢧ
ꢠ
ꢟ
ꢞ
ꢭ
ꢢ
ꢐ
ꢝ
ꢡ
ꢧ
ꢤ
ꢣ
ꢢ
ꢝ
ꢪ
ꢢ
ꢠ
ꢪ
ꢮ
ꢢ
ꢣ ꢧ ꢤ ꢣꢜ ꢝꢰ ꢟꢞ ꢢ ꢩꢩ ꢨꢢ ꢠ ꢢ ꢡ ꢧ ꢣ ꢧ ꢠ ꢤ ꢫ
ꢠ
ꢠ
ꢢ
ꢝ
ꢣ
ꢯ
ꢫ
ꢚ
ꢠ
ꢟ
ꢪ
ꢦ
ꢥ
ꢣ
ꢜ
ꢟ
ꢝ
ꢨ
ꢠ
ꢟ
ꢥ
ꢧ
ꢤ
ꢤ
ꢜ
ꢝ
ꢰ
ꢪ
ꢟ
ꢧ
ꢤ
ꢝ
ꢟ
ꢣ
ꢝ
ꢧ
ꢥ
ꢧ
ꢤ
ꢤ
ꢢ
ꢠ
ꢜ
ꢩ
ꢯ
ꢜ
ꢝ
ꢥ
ꢩ
ꢦ
ꢪ
ꢧ
1
www.ti.com
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢇ
ꢀ ꢁ ꢂꢃ ꢄꢅ ꢈꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
DESCRIPTION (continued)
The bq2057 then begins the constant-voltage phase. The accuracy of the voltage regulation is better than 1%
over the operating-temperature and supply-voltage ranges. For single and dual cells, the bq2057 is offered in
four fixed-voltage versions: 4.1 V, 4.2 V, 8.2 V, and 8.4 V. Charge stops when the current tapers to the charge
termination threshold, I
. The bq2057 automatically restarts the charge if the battery voltage falls below
(TERM)
the V
threshold.
(RCH)
The designer also may use the AutoComp feature to reduce charging time. This proprietary technique allows
safe and dynamic compensation for the internal impedance of the battery pack during charge.
AVAILABLE OPTIONS
PACKAGE
†
MSOP
T
CHARGE REGULATION
VOLTAGE
SOIC
(SN)
TSSOP
(TS)
A
(DGK)
bq2057DGK
bq2057CDGK
4.1 V
4.2 V
8.2 V
8.4 V
Not available
bq2057CSN
Not available
bq2057WSN
bq2057TS
bq2057CTS
bq2057TTS
bq2057WTS
−20°C to 70°C
Not available
†
Note the difference in pinout for this package.
2
www.ti.com
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢇ
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
function block diagram
VCC
V
Internal Reference
CC
_
+
DONE
Sleep Mode
_
+
V-Control
I-Control
BAT
CC
Voltage Regulation
COMP
G
(comp)
+
_
Battery
Recharge
V
CC
+
_
V
CC
Battery
Conditioning
Control
Block
STAT
_
+
TS
TS2 Trip
_
+
TS1 Trip
I-Control
_
0.5 V
High/Low SNS Set
CC
+
SNS
+
_
V
−V
CC (SNS)
Current Regulation
Charge Termination
V
−V
SS (SNS)
+
_
VSS
3
www.ti.com
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢇ
ꢀ ꢁ ꢂꢃ ꢄꢅ ꢈꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
Terminal Functions
TERMINAL
NO.
I/O
DESCRIPTION
NAME
SOIC (SN) and
TSSOP (TS)
MSOP
(DGK)
BAT
2
7
8
1
5
4
3
6
8
5
6
7
3
2
1
4
I
O
I
Voltage sense input
Charge control output
CC
COMP
SNS
STAT
TS
Charge-rate compensation input (AutoComp)
Current sense input
I
O
I
Charge status output
Temperature sense input
Supply voltage
VCC
VSS
I
Ground
detailed description
current-sense input
Battery current is sensed via the voltage developed on this pin by an external sense resistor. The external
resistor can be placed on either the high or low side of the battery. (See schematics for details.)
battery-voltage input
Voltage sense-input tied directly to the positive side of the battery.
temperature sense input
Input for an external battery-temperature monitoring circuit. Connecting this input to VCC/2 disables this feature.
charge-status output
3-state indication of charge in progress, charge complete, and temperature fault or sleep mode.
charge-control output
Source-follower output that drives an external pass-transistor (PNP or P-channel MOSFET) for current and
voltage regulation.
charge-rate compensation input
Sets the charge-rate compensation level. The voltage-regulation output may be programmed to vary as a
function of the charge current delivered to the battery.
supply voltage input
Power supply input and current reference for high-side sensing configuration.
4
www.ti.com
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢇ
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
†
absolute maximum ratings over operating free-air temperature (unless otherwise noted)
Supply voltage (V
with respect to GND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 to +18 V
CC
Input voltage, SNS, BAT, TS, COMP (all with respect to GND) . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to V +0.3 V
Sink current (STAT pin) not to exceed P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
Source current (STAT pin) not to exceed P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 mA
Output current (CC pin) not to exceed P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA
CC
D
D
D
Total power dissipation, P (at 25°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300mW
D
Operating free-air temperature range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −20°C to 70°C
A
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 125°C
stg
Lead temperature (soldering, 10 s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
DERATING FACTOR
T
≤ 25°C
T = 70°C
A
POWER RATING
A
PACKAGE
ABOVE T = 25°C
POWER RATING
A
DGK
3.4 mW/°C
424 mW
271 mW
recommended operating conditions
MIN
MAX
15
UNIT
V
Supply voltage, V
CC
4.5
Operating free-air temperature range, T
−20
70
°C
A
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
I
V
V
Current
V > V
CC CC(min)
, Excluding external loads
2
4
mA
(VCC)
CC
For bq2057 and bq2957C,
≥ V
3
6
V
(BAT)
,
V
(BAT)
– V
≥ 0.8 V
≥ 0.8 V
(min)
CC
I
Sleep current
µA
(VCCS)
CC
For bq2057T and bq2957W,
10
V
(BAT)
≥ V
,
V
(BAT)
– V
(min)
CC
I
I
I
I
Input bias current on BAT pin
Input bias current on SNS pin
Input bias current on TS pin
Input bias current on COMP pin
V
= V
1
5
5
5
µA
µA
µA
µA
IB(BAT)
IB(SNS)
IB(TS)
(BAT)
(REG)
V(
= 5 V
= 5 V
SNS)
V
V
(TS)
= 5 V
IB(COMP)
(COMP)
BATTERY VOLTAGE REGULATION
bq2057, See Notes 1, 2, 3
4.059
4.158
8.119
8.317
4.10 4.141
4.20 4.242
8.20 8.282
8.40 8.484
bq2057C, See Notes 1, 2, 3
bq2057T, See Notes 1, 2, 3
bq2057W, See Notes 1, 2, 3
V
Output voltage
V
O(REG)
NOTES: 1. For high-side current sensing configuration
2. For low-side current sensing configuration, the tolerance is 1% for T = 25°C and 1.2% for −20°C ≥ T ≥ 70°C
A
A
3.
V +0.3 V ≤ V
(BAT) CC
≤ V
CC(max)
5
www.ti.com
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢇ
ꢀ ꢁ ꢂꢃ ꢄꢅ ꢈꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
CURRENT REGULATION
bq2057 and bq2057C,
High-side current sensing configuration
95.4
113.6
100
105
125
110
130
115.5
137.5
121
bq2057T and bq2057W,
High-side current sensing configuration
Current regulation
threshold
V
mV
(SNS)
bq2057 and bq2057C,
Low-side current sensing configuration
bq2057T and bq2057W,
Low-side current sensing configuration
118.1
143
CHARGE TERMINATION DETECTION
Charge termination Voltage at pin SNS, relative to V
for high-side
CC
sensing, and to Vss for low-side sensing,
I
current detect
threshold
−24
−14
−4
mV
(TERM)
0°C ≤ T ≤ 50°C
A
TEMPERATURE COMPARATOR
Lower temperature
threshold
V
29.1
58.3
30
60
30.9
61.8
(TS1)
(TS2)
TS pin voltage
%V
CC
Upper temperature
threshold
V
PRECHARGE COMPARATOR
bq2057
2.94
3.04
5.98
6.18
3
3.1
6.1
6.3
3.06
3.16
6.22
6.43
bq2057C
bq2057T
bq2057W
Precharge
threshold
V
(min)
V
PRECHARGE CURRENT REGULATION
Voltage at pin SNS, relative to V
for high-side
CC
for low-side sensing,
sensing, and to V
SS
13
13
mV
mV
Precharge current
regulation
0°C ≤ T ≤ 50°C
A
I
(PRECHG)
Voltage at pin SNS, relative to V
for high-side
= 5 V
CC
3
22
sensing, 0°C ≤ T ≤ 50°C, V
CC
A
V
RCH
COMPARATOR (Battery Recharge Threshold)
V
V
−
V
V
−
V
V
−
O(REG)
98 mV
O(REG)
100 mV
O(REG)
102 mV
bq2057 and bq2057C
Recharge
V
V
V/V
V
(RCH)
threshold
−
−
−
O(REG)
204 mV
O(REG)
O(REG)
bq2057T and bq2057W
196 mV
200 mV
CHARGE-RATE COMPENSATION (AutoComp)
V
+0.3 V≤ V ≤ V
, bq2057, bq2057C,
(BAT) CC CC(max)
1.87
2.09
2.2
2.4
2.53
2.76
bq2057T, bq2057W
G
AutoComp gain
(COMP)
V
+0.3 V ≤ V
≤ V
, bq2057T and
CC(max)
(BAT) CC
bq2057W in low-side sensing configuration
STAT PIN
Output (low)
voltage
V
I
I
= 10 mA
= 5 mA
0.7
OL(STAT)
OH(STAT)
OL
Output (high)
voltage
V
V
CC
-0.5
5
OH
CC PIN
V
Output low voltage
Sink current
I
= 5 mA (sink)
1.5
40
V
OL(CC)
O(CC)
I
Not to exceed power rating specification (P )
D
mA
O(CC)
6
www.ti.com
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢇ
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
Q1
FZT788B
R
0.2 Ω
SNS
PACK+
DC+
C1
0.1 µF
V
CC
R1
PACK−
1 kΩ
NTC
V
CC
bq2057
CC
COMP
R
T1
SNS
VCC
VSS
BAT
TS
TEMP
C2
STAT
0.1 µF
Battery
Pack
D1
GND
R
T2
R2
2 kΩ
Figure 1. Low Dropout Single- or Two-Cell Li-Ion/Li-Pol Charger
functional description
The bq2057 is an advanced linear charge controller for single or two-cell Li-Ion or Li-Pol applications. Figure 1
shows the schematic of charger using a PNP pass transistor. Figure 2 is an operational state diagram, and
Figure 3 is a typical charge profile. Figure 4 shows the schematic of a charger using P-channel MOSFET.
7
www.ti.com
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢇ
ꢀ ꢁ ꢂꢃ ꢄꢅ ꢈꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
POR
Sleep Mode
V
> V
)
CC
(BAT
Indicate SLEEP
MODE
(STAT = Hi-Z)
No
Checked at All
Times
Yes
Suspend Charge
TS Pin
in TS1 to TS2
Range
Indicate CHARGE
SUSPEND
(STAT = Hi-Z)
No
Yes
Regulate
(PRECHG)
I
V
<V
(BAT) (min)
Yes
Indicate
Charge In-Progress
(STAT = High)
Suspend Charge
No
Indicate CHARGE
SUSPEND
(STAT = Hi-Z)
TS Pin
in TS1 to TS2
Range
No
Regulate
Current or Voltage
Indicate
Charge In-Progress
(STAT = High)
Yes
TS Pin
in TS1 to TS2
Range
V
< V
(min)
No
Suspend Charge
(BAT)
No
TS Pin
in TS1 to TS2
Range
Indicate CHARGE
SUSPEND
No
(STAT = Hi-Z)
Yes
TS Pin
in TS1 to TS2
Range
Yes
Yes
No
V
< V
(min)
Yes
(BAT)
No
Terminate Charge
I
Indicate CHARGE
Done
(TERM)
Detected
Yes
No
Yes
V
< V
(RCH)
(BAT)
(STAT = Low)
Yes
Figure 2. Operation Flowchart
8
www.ti.com
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢇ
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
Preconditioning
Phase
Current Regulation
Phase
Voltage Regulation and Charge
Termination Phase
Regulation Voltage
Regulation Current
Minimum Charge
Voltage
Preconditioning
and Taper Detect
Figure 3. Typical Charge Profile
qualification and precharge
When power is applied, the bq2057 starts a charge-cycle if a battery is already present or when a battery is
inserted. Charge qualification is based on battery temperature and voltage. The bq2057 suspends charge if the
battery temperature is outside the V
to V
range and suspends charge until the battery temperature is
(TS1)
(TS2)
within the allowed range. The bq2057 also checks the battery voltage. If the battery voltage is below the
precharge threshold V , the bq2057 uses precharge to condition the battery. The conditioning charge rate
(min)
I
is set at approximately 10% of the regulation current. The conditioning current also minimizes heat
(PRECHG)
dissipation in the external pass-element during the initial stage of charge. See Figure 3 for a typical
charge-profile.
9
www.ti.com
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢇ
ꢀ ꢁ ꢂꢃ ꢄꢅ ꢈꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
Q1
SI6475DQ
R
0.2 Ω
SNS
D1
PACK+
PACK−
Battery
Pack
DC+
C2
0.1 µF
R2
1 kΩ
NTC
U1
bq2057
R
T1
CC
COMP
SNS
VCC
VSS
BAT
TS
TEMP
STAT
R4
R
T2
511 Ω
U2
C1
0.1 µF
R5
1 kΩ
CMD67−
22SRUC
R3
1 kΩ
GND
Figure 4. 0.5-A Charger Using P-Channel MOSFET
current regulation phase
The bq2057 regulates current while the battery-pack voltage is less than the regulation voltage, V
. The
, in series
O(REG)
bq2057 monitors charge current at the SNS input by the voltage drop across a sense-resistor, R
SNS
with the battery pack. In high-side current sensing configuration (Figure 5), R
is between the VCC and SNS
SNS
pins, and in low-side sensing (Figure 6) the R
is between VSS (battery negative) and SNS (charger ground)
SNS
pins. Charge-current feedback, applied through pin SNS, maintains a voltage of V
resistor. The following formula calculates the value of the sense resistor:
across the current sense
(SNS)
(1)
V
(SNS)
R
+
SNS
I
O(REG)
is the desired charging current.
Where I
O(REG)
10
www.ti.com
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢇ
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
DC+
DC+
R
SNS
BAT+
BAT+
bq2057
bq2057
SNS
COMP
SNS
COMP
BAT
VCC
TS
CC
VSS
BAT
VCC
TS
CC
VSS
STAT
STAT
DC−
BAT−
DC−
R
SNS
BAT−
Figure 5. High-Side Current Sensing
Figure 6. Low-Side Current Sensing
voltage regulation phase
The voltage regulation feedback is through the BAT pin. This input is tied directly to the positive side of the
battery pack. The bq2057 monitors the battery-pack voltage between the BAT and VSS pins. The bq2057 is
offered in four fixed-voltage versions: 4.1 V, 4.2 V, 8.2 V and 8.4 V.
Other regulation voltages can be achieved by adding a voltage divider between the positive and negative
terminals of the battery pack and using bq2057T or bq2057W. The voltage divider presents scaled battery-pack
voltage to BAT input. (See Figure 7 and Figure 8.) The resistor values RB1 and RB2 for the voltage divider are
calculated by the following equation:
(2)
V
R
R
(CELL)
B1
B2
+
N
–1
ǒ Ǔ
V
O(REG)
Where:
N = Number of cells in series
V
= Desired regulation voltage per cell
(CELL)
11
www.ti.com
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢇ
ꢀ ꢁ ꢂꢃ ꢄꢅ ꢈꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
DC+
DC+
BAT+
BAT−
R
SNS
BAT+
R
R
B1
B2
bq2057
R
R
B1
SNS
bq2057
COMP
SNS
COMP
BAT
VCC
TS
CC
VSS
B2
BAT
VCC
TS
CC
VSS
BAT−
STAT
R
SNS
STAT
DC−
DC−
Figure 7. Optional Voltage Divider for
Nonstandard Regulation Voltage,
(High-Side Current Sensing)
Figure 8. Optional Voltage Divider for
Nonstandard Regulation Voltage,
(Low-Side Current Sensing)
charge termination and recharge
The bq2057 monitors the charging current during the voltage-regulation phase. The bq2057 declares a done
condition and terminates charge when the current tapers off to the charge termination threshold, I . A new
(TERM)
charge cycle begins when the battery voltage falls below the V
threshold.
(RCH)
battery temperature monitoring
The bq2057 continuously monitors temperature by measuring the voltage between the TS and VSS pins. A
negative- or a positive-temperature coefficient thermistor (NTC, PTC) and an external voltage divider typically
develop this voltage. (See Figure 9.) The bq2057 compares this voltage against its internal V
thresholds to determine if charging is allowed. (See Figure 10.) The temperature sensing circuit is immune to
and V
(TS1)
(TS2)
any fluctuation in V , since both the external voltage divider and the internal thresholds (V
are referenced to VCC.
and V
)
CC
(TS1)
(TS2)
The resistor values of R
and R
are calculated by the following equations:
(T1)
(T2)
For NTC Thermistors
(3)
(4)
5 R
R
* R
TH
TC
TC
TH
R
R
+
+
T1
T2
ǒ
Ǔ
3 R
5 R
R
TH
TC
ǒ
Ǔ–ǒ7 R
Ǔ
ƫ
ƪ 2 R
TC
TH
12
www.ti.com
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢇ
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
battery temperature monitoring (continued)
For PTC Thermistors
(5)
(6)
5 R
R
* R
TH
TH
TC
TC
R
R
+
+
T1
T2
ǒ
Ǔ
3 R
5 R
R
TH
TC
ǒ
Ǔ–ǒ7 R
Ǔ
ƫ
ƪ 2 R
TH
TC
Where R
is the cold temperature resistance and R
is the hot temperature resistance of thermistor, as
(TC)
(TH)
specified by the thermistor manufacturer.
R
the V
or R can be omitted If only one temperature (hot or cold) setting is required. Applying a voltage between
T1
T2
and V
thresholds to pin TS disables the temperature-sensing feature.
(TS1)
(TS2)
DC+
DC+
R
SNS
BAT+
BAT+
bq2057
bq2057
R
T1
SNS
SNS
COMP
COMP
BAT
VCC
TS
BAT
VCC
TS
CC
VSS
CC
VSS
DC−
STAT
STAT
R
R
T1
T2
DC−
R
Thermistor
BAT−
T2
BAT−
Thermistor
R
SNS
High-Side Current Sensing
Low-Side Current Sensing
Figure 9. Temperature Sensing Circuits
V
CC
Temperature Fault
V
V
(TS2)
Normal Temperature Range
(TS1)
Temperature Fault
V
SS
Figure 10. bq2057 TS Input Thresholds
13
www.ti.com
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢇ
ꢀ ꢁ ꢂꢃ ꢄꢅ ꢈꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
charge inhibit function
The TS pin can be used as charge-inhibit input. The user can inhibit charge by connecting the TS pin to VCC
or VSS (or any level outside the V to V thresholds). Applying a voltage between the V and V
(TS2)
(TS1)
(TS2)
(TS1)
thresholds to pin TS returns the charger to normal operation.
charge status indication
The bq2057 reports the status of the charger on the 3-state STAT pin. The following table summarized the
operation of the STAT pin.
CONDITION
STAT PIN
High
Battery conditioning and charging
Charge complete (Done)
Low
Temperature fault or sleep mode
Hi-Z
The STAT pin can be used to drive a single LED (Figure 1), dual-chip LEDs (Figure 4) or for interface to a host
or system processor (Figure 11). When interfacing the bq2057 to a processor, the user can use an output port,
as shown in Figure 11, to recognize the high-Z state of the STAT pin. In this configuration, the user needs to
read the input pin, toggle the output port and read the STAT pin again. In a high-Z condition, the input port always
matches the signal level on the output port.
Host
Processor
bq2057CTS
SNS
COMP
BAT
VCC
TS
OUT
CC
VSS
IN
STAT
Figure 11. Interfacing the bq2057 to a Host Processor
low-power sleep mode
The bq2057 enters the sleep mode if the VCC falls below the voltage at the BAT input. This feature prevents
draining the battery pack during the absence of VCC.
14
www.ti.com
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢇ
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
selecting an external pass-transistor
The bq2057 is designed to work with both PNP transistor and P-channel MOSFET. The device should be chosen
to handle the required power dissipation, given the circuit parameters, PCB layout and heat sink configuration.
The following examples illustrate the design process for either device:
PNP transistor:
Selection steps for a PNP bipolar transistor: Example: V = 4.5 V, I
= 1 A, 4.2-V single-cell Li-Ion (bq2057C).
I
(REG)
V is the input voltage to the charger and I
is the desired charge current (see Figure 1).
I
(REG)
1. Determine the maximum power dissipation, P , in the transistor.
D
The worst case power dissipation happens when the cell voltage, V
, is at its lowest (typically 3 V at the
(BAT)
beginning of current regulation phase) and V is at its maximum.
I
Where V
is the voltage drop across the current sense resistor.
CS
P = (V − V
– V ) × IREG
(BAT)
(7)
D
I
CS
P = (4.5 – 0.1 − 3) × 1 A
D
P = 1.4 W
D
2. Determine the package size needed in order to keep the junction temperature below the manufacturer’s
recommended value, T
. Calculate the total theta, θ(°C/W), needed.
(J)max
(8)
ǒT(J)max
150–40
1.4
Ǔ
* T
A(max)
θ
+
+
JC
P
D
(
)
θ
θ
JC
JC
+ 78°CńW
Now choose a device package with a theta at least 10% below this value to account for additional thetas
other than the device. A SOT223 package, for instance, has typically a theta of 60°C/W.
3. Select a collector-emitter voltage, V
be adequate in this example.
, rating greater than the maximum input voltage. A 15-V device will
(CE)
4. Select a device that has at least 50% higher drain current I rating than the desired charge current I
.
C
(REG)
5. Using the following equation, calculate the minimum beta (β or h ) needed:
FE
(9)
I
CMAX
b
+
+
min
I
B
1
b
min
min
0.035
b
+ 28
where I
is the maximum collector current (in this case same as I
), and I is the base current
max(C))
(REG) B
(chosen to be 35 mA in this example).
NOTE:
The beta of a transistor drops off by a factor of 3 over temperature and also drops off with load.
Therefore, note the beta of device at I and the minimum ambient temperature when choosing
(REG)
the device. This beta should be larger than the minimum required beta.
Now choose a PNP transistor that is rated for V
SOT223 package.
≥15 V, θ ≤ 78°C/W, I ≥ 1.5 A, β ≥ 28 and that is in a
min
(CE)
JC
C
15
www.ti.com
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢇ
ꢀ ꢁ ꢂꢃ ꢄꢅ ꢈꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
selecting an external pass-transistor (continued)
P-channel MOSFET:
Selection steps for a P-channel MOSFET: Example: V = 5.5 V, I
= 500 mA, 4.2-V single-cell Li−Ion
I
(REG)
(bq2057C). V is the input voltage to the charger and I
is the desired charge current. (See Figure 4.)
I
(REG)
1. Determine the maximum power dissipation, P , in the transistor.
D
The worst case power dissipation happens when the cell voltage, V
, is at its lowest (typically 3 V at
(BAT)
the beginning of current regulation phase) and V is at its maximum.
I
Where V is the forward voltage drop across the reverse-blocking diode (if one is used), and V
D
voltage drop across the current sense resistor.
is the
(10)
CS
P = (V – V − V
– V
) × I
D
I
D
(CS)
(BAT) (REG)
P = (5.5 – 0.4 – 0.1 −3) × 0.5 A
D
P = 1 W
D
2. Determine the package size needed in order to keep the junction temperature below the manufacturer’s
recommended value, T . Calculate the total theta, θ(°C/W), needed.
JMAX
(11)
ǒTmax(J) A(max)
150–40
1
Ǔ
–T
θ
+
+
JC
P
D
(
)
θ
θ
JC
JC
+ 110°CńW
Now choose a device package with a theta at least 10% below this value to account for additional thetas
other than the device. A TSSOP-8 package, for instance, has typically a theta of 70°C/W.
3. Select a drain-source voltage, V
adequate in this example.
, rating greater than the maximum input voltage. A 12 V device will be
(DS)
4. Select a device that has at least 50% higher drain current (I ) rating than the desired charge current I
D
.
(REG)
5. Verify that the available drive is large enough to supply the desired charge current.
V
V
V
= (V +V
+ V
) − V
I
(12)
(GS)
(GS)
(GS)
D
(CS)
OL(CC)
= (0.4 + 0.1 + 1.5) – 5.5
= −3.5
Where V
(if one is used), and V
output low voltage specification for the bq2057.
is the gate-to-source voltage, V is the forward voltage drop across the reverse-blocking diode
D
(GS)
is the voltage drop across the current sense resistor, and V
is the CC pin
CS
OL(CC)
Select a MOSFET with gate threshold voltage, V
, rating less than the calculated V
.
(GSth)
(GS)
Now choose a P-channel MOSFET transistor that is rated for VDS ≤ −15 V, θ
(GSth)
≤ 110°C/W, I ≥ 1 A,
D
JC
V
≥ −3.5 V and in a TSSOP package.
16
www.ti.com
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢇ
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
selecting input capacitor
In most applications, all that is needed is a high-frequency decoupling capacitor. A 0.1 µF ceramic, placed in
proximity to VCC and VSS pins, works well. The bq2057 works with both regulated and unregulated external
dc supplies. If a non-regulated supply is chosen, the supply unit should have enough capacitance to hold up
the supply voltage to the minimum required input voltage at maximum load. If not, more capacitance must be
added to the input of the charger.
selecting output capacitor
The bq2057 does not require any output capacitor for loop stability. The user can add output capacitance in order
to control the output voltage when a battery is not present. The charger quickly charges the output capacitor
to the regulation voltage, but the output voltage decays slowly, because of the low leakage current on the BAT
pin, down to the recharge threshold. Addition of a 0.1µF ceramic capacitor, for instance, results in a 100 mV(pp)
ripple waveform, with an approximate frequency of 25Hz. Higher capacitor values can be used if a lower
frequency is desired.
automatic charge-rate compensation
To reduce charging time, the bq2057 uses the proprietary AutoComp technique to compensate safely for
internal impedance of the battery pack. The AutoComp feature is disabled by connecting the COMP pin to VCC
in high-side current-sensing configuration, and to VSS in low-side current-sensing configuration. The COMP
pin must not be left floating.
Figure 12 outlines the major components of a single-cell Li-Ion battery pack. The Li-Ion battery pack consists
of a cell, protection circuit, fuse, connector, current sense-resistors, and some wiring. Each of these components
contains some resistance. Total impedance of the battery pack is the sum of the minimum resistances of all
battery-pack components. Using the minimum resistance values reduces the odds for overcompensating.
Overcompensating may activate the safety circuit of the battery pack.
BAT+
Wire
Fuse
Terminal
Cell
Protection
Controller
BAT−
Wire
Wire
Wire
Terminal
Discharge
Charge
Figure 12. Typical Components of a Single-Cell Li-Ion Pack
Compensation is achieved through input pin COMP (Figure 13). A portion of the current-sense voltage,
presented through this pin, is scaled by a factor of G
and summed with the regulation threshold, V
.
(COMP)
O(REG)
This process increases the output voltage to compensate for the battery pack’s internal impedance and for
undesired voltage drops in the circuit.
17
www.ti.com
ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢇ
ꢀ ꢁ ꢂꢃ ꢄꢅ ꢈꢆ ꢀ ꢁ ꢂ ꢃꢄ ꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
automatic charge-rate compensation (continued)
AutoComp setup requires the following information:
D
D
Total impedance of battery pack (Z
)
(PACK)
Maximum charging current (I
(REG)
)
The voltage drop across the internal impedance of battery pack, V , can then be calculated using the following
(Z)
equation:
V
= Z
× I
(PACK) (REG)
(13)
(14)
(Z)
The required compensation is then calculated using the following equations:
V
(Z)
V
+
(COMP)
G
(COMP)
O(REG)
) ǒG(COMP)
Ǔ
V
+ V
V
(PACK)
(COMP
Where V
is the voltage on COMP pin. This voltage is referenced to VCC in high-side current sensing
(COMP)
configuration and to VSS for low-side sensing. V
is the voltage across the battery pack.
(PACK)
The values of R
and R can be calculated using the following equation:
(COMP2)
(COMP1)
(15)
V
R
(COMP)
COMP2
+
V
R
) R
(SNS)
COMP1
COMP2
DC+
BAT+
DC+
R
COMP2
BAT+
R
COMP1
bq2057
bq2057
SNS
COMP
R
SNS
SNS
COMP
BAT
VCC
TS
CC
VSS
BAT
VCC
TS
CC
VSS
DC−
STAT
STAT
DC−
R
COMP2
R
R
SNS
COMP1
BAT−
High-Side Current Sensing
Low-Side Current Sensing
Figure 13. AutoComp Circuits
18
www.ti.com
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢇ
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
APPLICATION INFORMATION
automatic charge-rate compensation (continued)
The following example illustrates these calculations:
Assume Z
V
= 100 mΩ, I
= 500 mA, high-side current sensing bq2057C
(REG)
(PACK)
(16)
(17)
+ Z
I
(Z)
(PACK)
(REG)
V
+ 0.1 0.5
= 50 mV
(Z)
V
(Z)
V
(Z)
V
+
(COMP)
(COMP)
G
(COMP)
0.05
2.2
V
+
V
= 22.7 mV
(COMP)
Let R
= 10 kΩ
COMP2
(18)
ǒV(SNS)
Ǔ
R
* V
COMP2
(COMP)
)
R
+
COMP1
V
(COMP)
(
105 mV * 22.7 mV
R
+ 10k
COMP1
22.7 mV
R
+ 36.25 kW
COMP1
Use the closest standard value (36.0 kΩ) for R
COMP1
19
www.ti.com
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢇ
ꢀ ꢁꢂ ꢃ ꢄ ꢅ ꢈꢆ ꢀꢁ ꢂꢃ ꢄꢅ ꢉ
SLUS025F − MAY 2001 − REVISED JULY 2002
MECHANICAL DATA
8−Pin SOIC Narrow (SN)
(
)
8−Pin SN 0.150” SOIC
Inches
Millimeters
Min.
Max.
Min.
Max.
Dimension
A
A1
B
0.060
0.004
0.013
0.007
0.185
0.150
0.045
0.225
0.015
0.070
0.010
0.020
0.010
0.200
0.160
0.055
0.245
0.035
1.52
0.10
0.33
0.18
4.70
3.81
1.14
5.72
0.38
1.78
0.25
0.51
0.25
5.08
4.06
1.40
6.22
0.89
C
D
E
e
H
L
TS: 8−Pin TSSOP
Inches
Millimeters
Dimension
Min.
Max.
Min.
Max.
A
A1
B
-
0.043
0.006
0.012
0.007
0.122
0.176
-
1.10
0.15
0.30
0.18
3.10
4.48
0.002
0.007
0.004
0.114
0.169
0.05
0.18
0.09
2.90
4.30
C
D
E
e
0.0256BSC
0.65BSC
H
0.246
0.256
6.25
6.50
Notes:
1.
Controlling dimension: millimeters. Inches shown for reference only.
2
3
’D’ and ’E’ do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0,15 mm per side
Each lead centerline shall be located within 0,10 mm of its exact true position.
4
5
Leads shall be coplanar within 0,08 mm at the seating plane.
Dimension ’B’ does not include dambar protrusion. The dambar protrusion(s) shall not cause the lead width
to exceed ’B’ maximum by more than 0,08 mm.
6
7
Dimension applies to the flat section of the lead between 0,10 mm and 0,25 mm from the lead tip.
’A1’ is defined as the distance from the seating plane to the lowest point of the package body (base plane).
20
www.ti.com
PACKAGE OPTION ADDENDUM
www.ti.com
31-Oct-2013
PACKAGING INFORMATION
Orderable Device
BQ2057CDGK
BQ2057CDGKG4
BQ2057CDGKR
BQ2057CDGKRG4
BQ2057CSN
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
VSSOP
VSSOP
VSSOP
VSSOP
SOIC
DGK
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
80
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
CU NIPDAUAG
CU NIPDAUAG
CU NIPDAUAG
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAUAG
CU NIPDAUAG
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
2057C
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DGK
DGK
DGK
D
80
2500
2500
75
Green (RoHS
& no Sb/Br)
2057C
2057C
2057C
2057C
2057C
2057C
2057C
2057C
2057C
2057C
2057C
2057
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
BQ2057CSNG4
BQ2057CSNTR
BQ2057CSNTRG4
BQ2057CTS
SOIC
D
75
Green (RoHS
& no Sb/Br)
SOIC
D
2500
2500
150
150
2000
2000
80
Green (RoHS
& no Sb/Br)
SOIC
D
Green (RoHS
& no Sb/Br)
TSSOP
TSSOP
TSSOP
TSSOP
VSSOP
VSSOP
SOIC
PW
PW
PW
PW
DGK
DGK
D
Green (RoHS
& no Sb/Br)
BQ2057CTSG4
BQ2057CTSTR
BQ2057CTSTRG4
BQ2057DGK
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
BQ2057DGKG4
BQ2057SN
80
Green (RoHS
& no Sb/Br)
2057
75
Green (RoHS
& no Sb/Br)
2057
BQ2057SNG4
BQ2057TS
SOIC
D
75
Green (RoHS
& no Sb/Br)
2057
TSSOP
PW
150
Green (RoHS
& no Sb/Br)
2057
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
31-Oct-2013
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
-20 to 70
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
BQ2057TSG4
BQ2057TSN
ACTIVE
TSSOP
SOIC
PW
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
2057
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
D
D
75
75
Green (RoHS
& no Sb/Br)
2057T
2057T
2057T
2057T
2057T
2057T
2057W
2057W
2057W
2057W
2057W
2057W
2057W
2057W
BQ2057TSNG4
BQ2057TTS
SOIC
Green (RoHS
& no Sb/Br)
TSSOP
TSSOP
TSSOP
TSSOP
SOIC
PW
PW
PW
PW
D
150
150
2000
2000
75
Green (RoHS
& no Sb/Br)
BQ2057TTSG4
BQ2057TTSTR
BQ2057TTSTRG4
BQ2057WSN
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
BQ2057WSNG4
BQ2057WSNTR
BQ2057WSNTRG4
BQ2057WTS
SOIC
D
75
Green (RoHS
& no Sb/Br)
SOIC
D
2500
2500
150
150
2000
2000
Green (RoHS
& no Sb/Br)
SOIC
D
Green (RoHS
& no Sb/Br)
TSSOP
TSSOP
TSSOP
TSSOP
PW
PW
PW
PW
Green (RoHS
& no Sb/Br)
BQ2057WTSG4
BQ2057WTSTR
BQ2057WTSTRG4
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
31-Oct-2013
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Jun-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
BQ2057CDGKR
BQ2057CSNTR
BQ2057CTSTR
BQ2057TTSTR
BQ2057WSNTR
BQ2057WTSTR
VSSOP
SOIC
DGK
D
8
8
8
8
8
8
2500
2500
2000
2000
2500
2000
330.0
330.0
330.0
330.0
330.0
330.0
12.4
12.4
12.4
12.4
12.4
12.4
5.3
6.4
7.0
7.0
6.4
7.0
3.4
5.2
3.6
3.6
5.2
3.6
1.4
2.1
1.6
1.6
2.1
1.6
8.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
12.0
Q1
Q1
Q1
Q1
Q1
Q1
TSSOP
TSSOP
SOIC
PW
PW
D
TSSOP
PW
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Jun-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
BQ2057CDGKR
BQ2057CSNTR
BQ2057CTSTR
BQ2057TTSTR
BQ2057WSNTR
BQ2057WTSTR
VSSOP
SOIC
DGK
D
8
8
8
8
8
8
2500
2500
2000
2000
2500
2000
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
35.0
35.0
35.0
35.0
35.0
35.0
TSSOP
TSSOP
SOIC
PW
PW
D
TSSOP
PW
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
BQ2057WSNG4
ADVANCED LINEAR CHARGE MANAGEMENT IC FOR SINGLE-AND TWO-CELL LITHIUM-ION AND LITHIUM-POLYMER
TI
BQ2057WSNTRG4
ADVANCED LINEAR CHARGE MANAGEMENT IC FOR SINGLE-AND TWO-CELL LITHIUM-ION AND LITHIUM-POLYMER
TI
BQ2057WTSG4
ADVANCED LINEAR CHARGE MANAGEMENT IC FOR SINGLE-AND TWO-CELL LITHIUM-ION AND LITHIUM-POLYMER
TI
BQ2057WTSTRG4
ADVANCED LINEAR CHARGE MANAGEMENT IC FOR SINGLE-AND TWO-CELL LITHIUM-ION AND LITHIUM-POLYMER
TI
©2020 ICPDF网 联系我们和版权申明