ADC0804LCWM_技术文档

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

8-Bit µP Compatible A/D Converters

Check for Samples: ADC0801, ADC0802, ADC0803, ADC0804, ADC0805

1

FEATURES

DESCRIPTION

The ADC0801, ADC0802, ADC0803, ADC0804 and

•

Compatible with 8080 µP derivatives – no

ADC0805 are CMOS 8-bit successive approximation

A/D converters that use a differential potentiometric

ladder — similar to the 256R products. These

converters are designed to allow operation with the

NSC800 and INS8080A derivative control bus with

TRI-STATE output latches directly driving the data

bus. These A/Ds appear like memory locations or I/O

ports to the microprocessor and no interfacing logic is

needed.

interfacing logic needed – access time 135 ns

•

Easy interface to all microprocessors, or

operates “stand alone”

•

Differential analog voltage inputs

Logic inputs and outputs meet both MOS and

TTL voltage level specifications

•

Works with 2.5V (LM336) voltage reference

On-chip clock generator

Differential analog voltage inputs allow increasing the

common-mode rejection and offsetting the analog

zero input voltage value. In addition, the voltage

reference input can be adjusted to allow encoding

any smaller analog voltage span to the full 8 bits of

resolution.

0V to 5V analog input voltage range with

single 5V supply

•

No zero adjust required

0.3" standard width 20-pin DIP package

20-pin molded chip carrier or small outline

package

CONNECTION DIAGRAM

•

Operates ratiometrically or with 5 V_DC, 2.5 V_DC

or analog span adjusted voltage reference

,

ADC080X

Dual-In-Line and Small Outline (SO) Packages

See Ordering Information

KEY SPECIFICATIONS

•

Resolution: 8 Bits

Total error: ±1/4 LSB, ±1/2 LSB and ±1 LSB

Conversion Time: 100 µs

Table 1. ORDERING INFORMATION

TEMP RANGE

±1/4 Bit Adjusted

0°C TO 70°C

0°C to 70°C

−40°C TO +85°C

ADC0801LCN

ERROR

±1/2 Bit Unadjusted

±1/2 Bit Adjusted

±1Bit Unadjusted

ADC0802LCWM

ADC0802LCN

ADC0803LCN

ADC0804LCWM

ADC0804LCN

ADC0805LCN/ADC0804LCJ

PACKAGE OUTLINE

Z-80® is a registered trademark of Zilog Corp.

M20B — Small Outline

N20A — Molded DIP

1

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

TYPICAL APPLICATIONS

8080 Interface

ERROR SPECIFICATION (Includes Full-Scale, Zero Error, and Non-Linearity)

V_REF/2 = 2.500 V_DC

(No Adjustments)

V_REF/2 = No Connection

(No Adjustments)

FULL-SCALE

ADJUSTED

PART NUMBER

ADC0801

ADC0802

ADC0803

ADC0804

ADC0805

±1⁄4 LSB

±1⁄2 LSB

±1 LSB

ABSOLUTE MAXIMUM RATINGS

If Military/Aerospace specified devices are required, contact the National Semiconductor Sales Office/Distributors for

availability and specifications.

VALUE

UNIT

V

(1)

Supply voltage (V_CC

)

6.5

Logic control inputs

–0.3 to +18

V

Voltage

At other input and outputs

–0.3 to (V_CC+0.3)

V

Dual-In-Line Package (plastic

Dual-In-Line Package (ceramic)

Surface Mount Package Vapor Phase (60 seconds)

Infrared (15 seconds)

260

300

°C

mW

V

Lead Temperature

(Soldering, 10 seconds)

215

220

Storage Temperature Range

–65 to +150

875

Package Dissipation at T_A= 25°C

ESD Susceptibility⁽²⁾

800

(1) A zener diode exists, internally, from V_CCto GND and has a typical breakdown voltage of 7 V_DC

.

(2) Human body model, 100 pF discharged through a 1.5 kΩ resistor.

2

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

(1)(2)

OPERATING RATINGS

over operating free-air temperature range (unless otherwise noted)

Temperature Range

ADC0804LCJ

T_MIN≤ T_A≤ T_MAX

–40°C ≤ T_A≤ +85°C

0°C ≤ T_A≤ +70°C

4.5 V_DCto 6.3 V_DC

ADC0801/02/03/05LCN

ADC0804LCN

ADC0802/04LCWM

Range of V_CC

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not

apply when operating the device beyond its specified operating conditions.

(2) All voltages are measured with respect to GND, unless otherwise specified. The separate A GND point should always be wired to the D

GND.

ELECTRICAL CHARACTERISTICS

The following specifications apply for V_CC= 5 V_DC, T_MIN≤ T_A≤ T_MAXand f_CLK= 640 kHz (unless otherwise specified).

PARAMETER

CONDITIONS

MIN

TYP

MAX UNITS

ADC0801: Total Adjusted Error⁽¹⁾With Full-Scale Adj. (See Full-Scale)

±1/4

±1/2

±1

LSB

ADC0802: Total Unadjusted

V_REF/2=2.500 V_DC

Error⁽¹⁾

ADC0803: Total Adjusted Error⁽¹⁾With Full-Scale Adj.(See Full-Scale)

ADC0804: Total Unadjusted

Error

V_REF/2=2.500 VDC

(1)

ADC0805: Total Unadjusted

Error

V_REF/2-No Connection

±1

LSB

(1)

ADC0801/02/03/05

2.5

8

V_REF/2 Input Resistance (Pin 9)

kΩ

(2)

ADC0804

0.75

1.1

GND–0.0

5

Analog Input Voltage Range

DC Common-Mode Error

Power Supply Sensitivity

V(+) or V(–)⁽³⁾

V_CC+0.05

±1/8

V_DC

LSB

Over Analog Input Voltage Range

±1/16

V_CC=5 V_DC±10% Over Allowed V_IN(+) and V_IN(–) Voltage

Range⁽³⁾

±1/8

(1) None of these A/Ds requires a zero adjust (see Zero Error). To obtain zero code at other analog input voltages see Errors and

Reference Voltage Adjustments and Figure 51.

(2) The V_REF/2 pin is the center point of a two-resistor divider connected from V_CCto ground. In all versions of the ADC0801, ADC0802,

ADC0803, and ADC0805, and in the ADC0804LCJ, each resistor is typically 16 kΩ. In all versions of the ADC0804 except the

ADC0804LCJ, each resistor is typically 2.2 kΩ.

(3) For V_IN(−)≥ VIN(+) the digital output code will be 0000 0000. Two on-chip diodes are tied to each analog input (see block diagram)

which will forward conduct for analog input voltages one diode drop below ground or one diode drop greater than the V_CCsupply. Be

careful, during testing at low V_CClevels (4.5V), as high level analog inputs (5V) can cause this input diode to conduct–especially at

elevated temperatures, and cause errors for analog inputs near full-scale. The spec allows 50 mV forward bias of either diode. This

means that as long as the analog V_INdoes not exceed the supply voltage by more than 50 mV, the output code will be correct. To

achieve an absolute 0 V_DCto 5 V_DCinput voltage range will therefore require a minimum supply voltage of 4.950 V_DCover temperature

variations, initial tolerance and loading.

Submit Documentation Feedback

3

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

AC ELECTRICAL CHARACTERISTICS

The following specifications apply for V_CC=5 V_DCand T_MIN≤ T_A≤T_MAX(unless otherwise specified)

PARAMETER

CONDITIONS

f_CLK= 640 kHz⁽¹⁾

MIN

103

66

TYP

MAX UNITS

114

µs

T_C

Conversion Time

(2)(1)

See

73 1/fCLK

Clock Frequency

Clock Duty Cycle

100

40%

640

1460

kHz

f_CLK

V_CC= 5V⁽²⁾

60%

INTR tied to WR with CS = 0 VDC,

f_CLK= 640 kHz

CR

Conversion Rate in Free-Running Mode

Width of WR Input (Start Pulse Width)

8770

100

9708

conv/s

ns

(3)

t_W(WR)L

tACC

CS = 0 VDC

Access Time (Delay from Falling Edge of RD

to Output Data Valid)

C_L= 100 pF

135

125

300

200

450

ns

TRI-STATE Control (Delay from Rising Edge of C_L= 10 pF, R_L= 10k (See TRI-STATE

t1H, t0H

t_WI, t_RI

ns

RD to Hi-Z State)

TEST CIRCUITS AND WAVEFORMS)

Delay from Falling Edge of WR or RD to Reset

of INTR

C_IN

Input Capacitance of Logic Control Inputs

5

7.5

pF

C_OUT

TRI-STATE Output Capacitance (Data Buffers)

CONTROL INPUTS [Note: CLK IN (Pin 4) is the input of a Schmitt trigger circuit and is therefore specified separately]

V_IN(1)

V_IN(0)

I_IN(1)

I_IN(0)

Logical “1” Input Voltage (Except Pin 4 CLK IN) V_CC= 5.25 VDC

Logical “0” Input Voltage (Except Pin 4 CLK IN) V_CC= 4.75 VDC

2

15

0.8

1

V_DC

Logical “1” Input Current (All Inputs)

Logical “0” Input Current (All Inputs)

V_IN= 5 VDC

V_IN= 0 VDC

0.005

–1 –0.005

µA_DC

CLOCK IN AND CLOCK R

CLK IN (Pin 4) Positive Going Threshold

Voltage

V_T+

2.7

3.1

3.5

2.1

V_DC

CLK IN (Pin 4) Negative Going Threshold

Voltage

V_T−

1.5

0.6

1.8

1.3

V_H

CLK IN (Pin 4) Hysteresis (V_T+)–(V_T−)

2

V_DC

V_OUT(0) Logical “0” CLK R Output Voltage

V_OUT(1) Logical “1” CLK R Output Voltage

DATA OUTPUTS AND INTR

Logical “0” Output Voltage

I_O= 360 µA, V_CC= 4.75 VDC

0.4

I_O= −360 µA, V_CC= 4.75 VDC

2.4

V_OUT(0) Data Outputs

I_OUT= 1.6 mA, V_CC= 4.75 V_DC

I_OUT= 1.0 mA, V_CC= 4.75 V_DC

I_O= −360 µA, V_CC= 4.75 V_DC

I_O= −10 µA, V_CC= 4.75 V_DC

V_OUT= 0 VDC

0.4

V_DC

INTR Output

2.4

4.5

–3

V_DC

V_OUT(1) Logical “1” Output Voltage

V_DC

µA_DC

mA_DC

TRI-STATE Disabled Output Leakage (All Data

Buffers)

I_OUT

V_OUT= 5 VDC

3

I_SOURCE

I_SINK

POWER SUPPLY

Supply Current (Includes Ladder Current)

V_OUTShort to GND, T_A= 2 5°C

V_OUTShort to V_CC, T_A= 25°C

4.5

9

6

16

f_CLK= 640 kHz, V_REF/2 = NC,

T_A= 25°C and CS = 5 V

I_CC

ADC0801/02/03/04LCJ/05

ADC0804LCN/LCWM

1.1

1.9

1.8

2.5

mA

(1) Accuracy is specified at f_CLK= 640 kHz. At higher clock frequencies accuracy can degrade. For lower clock frequencies, the duty cycle

limits can be extended so long as the minimum clock high time interval or minimum clock low time interval is no less than 275 ns.

(2) With an asynchronous start pulse, up to 8 clock periods may be required before the internal clock phases are proper to start the

conversion process. The start request is internally latched, see Figure 48 and FUNCTIONAL DESCRIPTION.

(3) The CS input is assumed to bracket the WR strobe input and therefore timing is dependent on the WR pulse width. An arbitrarily wide

pulse width will hold the converter in a reset mode and the start of conversion is initiated by the low to high transition of the WR pulse

(see TIMING DIAGRAMS).

4

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

TYPICAL CHARACTERISTICS

spacer

Logic Input Threshold Voltage vs

Supply Voltage

Delay From Falling Edge of RD to Output

Data Valid vs Load Capacitance

Figure 1.

Figure 2.

CLK IN Schmitt Trip Levels vs

Supply Voltage

f_CLKvs Clock Capacitor

Figure 3.

Figure 4.

Full-Scale Error vs

Conversion Time

Effect of Unadjusted Offset Error

V_REF/2 Voltage

Figure 5.

Figure 6.

Submit Documentation Feedback

5

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

TYPICAL CHARACTERISTICS (continued)

spacer

Output Current

Temperature

Power Supply Current vs

Temperature⁽¹⁾

Figure 7.

Figure 8.

Linearity Error at Low

V_REF/2 Voltages

Figure 9.

(1) The V_REF/2 pin is the center point of a two-resistor divider connected from V_CCto ground. In all versions of the ADC0801, ADC0802,

ADC0803, and ADC0805, and in the ADC0804LCJ, each resistor is typically 16 kΩ. In all versions of the ADC0804 except the

ADC0804LCJ, each resistor is typically 2.2 kΩ.

6

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

TRI-STATE TEST CIRCUITS AND WAVEFORMS

SPACER

TIMING DIAGRAMS

All timing is measured from the 50% voltage points

Note: Read strobe must occur 8 clock periods (8/f_CLK) after assertion of interrupt to specify reset of INTR.

Figure 10. Ouatput Enable and Reset with INTR

Submit Documentation Feedback

7

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

TYPICAL APPLICATIONS

*For low power, see also LM385–2.5

Figure 12. Absolute with a 2.500V Reference

Figure 11. 6800 Interface

Note: before using caps at V_INor V_REF/2, see section Input Bypass

Capacitors.

Figure 13. Ratiometeric with Full-Scale Adjust

Figure 14. Absolute with a 5V Reference

Figure 15. Zero-Shift and Span Adjust: 2V ≤ V_IN≤ 5V

8

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

TYPICAL APPLICATIONS (continued)

Figure 16. Span Adjust: 0V ≤ V_IN≤ 3V

V_REF/2 = 256 mV

Figure 17. Directly Converting a Low-Level Signal

For: V_IN(+)>V_IN(−); Output = FF_HEX

For: V_IN(+) < V_IN(−); Output = 00_HEX

Figure 18. A µP Interfaced Comparator

Submit Documentation Feedback

9

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

TYPICAL APPLICATIONS (continued)

V_REF/2=128 mV; 1 LSB =1 mV; V_DAC≤ V_IN≤ (V_DAC+ 256 mV); 0 ≤ V_DAC< 2.5 V

Figure 19. 1 mV Resolution with µP Controlled Range

Figure 20. Digitizing a Current Flow

* Use a large R value to reduce loading at CLK R output.

Figure 21. Self-Clocking Multiple A/Ds

10

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

TYPICAL APPLICATIONS (continued)

*After power-up, a momentary grounding of the WR input is needed to

ensure operation.

Figure 22. Self-Clocking in Free-Running Mode

Figure 23. µP Interface for Free-Running A/D

J

100 kHz ≤ f_CLK≤ 1460 kHz

*_VIN(−) = 0.15 V_CC

15% of V_CC≤ V_XDR≤ 85% of V_CC

Figure 24. External clocking

Figure 25. Operating with “Automotive” Ratiometric

Transducers

Figure 26. Ratiometric with V_REF/2 Forced

Submit Documentation Feedback

11

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

TYPICAL APPLICATIONS (continued)

*See Figure 48 to select R value DB7 = “1” for V_IN(+)>V_IN(−)+(V_REF/2). Omit circuitry within the dotted area if

hysteresis is not needed.

Figure 27. µP Compatible Differential-Input Comparator with Pre-Set VOS (with or without Hysteresis)

*Beckman Instruments #694-3-R10K resistor array

Figure 28. Handling ±10V Analog Inputs

Figure 29. Low-Cost, µP Interfaced, Temperature-to-Digital

Converter

*Circuit values shown are for 0°C ≤ T_A≤ +128°C

**Can calibrate each sensor to allow easy replacement, then A/D can be calibrated with a pre-set input voltage.

Figure 30. µP Interfaced Temperature-to-Digital Converter

12

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

TYPICAL APPLICATIONS (continued)

*Beckman Instruments #694-3-R10K resistor array

Figure 31. Handling ±5V Analog Inputs

Figure 32. Read-Only Interface

Figure 33. µP Interfaced Comparator with Hysteresis

Submit Documentation Feedback

13

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

TYPICAL APPLICATIONS (continued)

Diodes are 1N914

Figure 34. Protecting the Input

Figure 35. Analog Self-Test for a System

*LM389 transistors A, B, C, D = LM324A quad op amp

Figure 36. A Low-Cost, 3-Decade Logarithmic Converter

14

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

TYPICAL APPLICATIONS (continued)

f_C=20 Hz

Uses Chebyshev implementation for steeper roll-off unity-gain, 2nd order, low-pass filter

Adding a separate filter for each channel increases system response time if an analog multiplexer is used

Figure 37. 3-Decade Logarithmic A/D Converter

*A/D output data is updated 1 CLK period prior to assertion of INTR

Figure 38. Noise Filtering the Analog Input

Figure 39. Output Buffers with A/D Data Enabled

*Allows output data to set-up at falling edge of CS

Figure 41. Increasing Bus Drive and/or

Reducing Time on Bus

Figure 40. Multiplexing Differential Inputs

Submit Documentation Feedback

15

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

TYPICAL APPLICATIONS (continued)

(1) Oversample whenever possible [keep fs > 2f(−60)] to eliminate input frequency folding (aliasing) and to allow for the

skirt response of the filter.

(2) Consider the amplitude errors which are introduced within the passband of the filter.

Figure 42. Sampling an AC Input Signal

(Complete shutdown takes ≈ 30 seconds.)

Figure 43. 70% Power Savings by Clock Gating

*Use ADC0801, 02, 03 or 05 for lowest power consumption.

Note: Logic inputs can be driven to V_CCwith A/D supply at zero volts.

Buffer prevents data bus from overdriving output of A/D when in shutdown mode.

Figure 44. Power Savings by A/D and V_REFShutdown

16

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

FUNCTIONAL DESCRIPTION

Understanding A/D Error Specs

A perfect A/D transfer characteristic (staircase waveform) is shown in Figure 45. The horizontal scale is analog

input voltage and the particular points labeled are in steps of 1 LSB (19.53 mV with 2.5V tied to the VREF/2 pin).

The digital output codes that correspond to these inputs are shown as D−1, D, and D+1. For the perfect A/D, not

only will center- value (A−1, A, A+1, . . . . ) analog inputs produce the cor- rect output digital codes, but also each

riser (the transitions between adjacent output codes) will be located ±1⁄2 LSB away from each center-value. As

shown, the risers are ideal and have no width. Correct digital output codes will be provided for a range of analog

input voltages that extend ±1⁄2 LSB from the ideal center-values. Each tread (the range of analog input voltage

that provides the same digital output code) is therefore 1 LSB wide.

Figure 46 shows a worst case error plot for the ADC0801. All center-valued inputs are guaranteed to produce the

correct output codes and the adjacent risers are specified to be no closer to the center-value points than ±1/4

LSB. In other words, if we apply an analog input equal to the center-value ±1/4 LSB, we guarantee that the A/D

will produce the correct digital code. The maximum range of the position of the code transition is indicated by the

horizontal arrow and it is specified to be no more than 1/2 LSB.

The error curve of Figure 47 shows a worst case error plot for the ADC0802. Here we guarantee that if we apply

an analog input equal to the LSB analog voltage center-value the A/D will produce the correct digital code.

Next to each transfer function is shown the corresponding error plot. Many people may be more familiar with

error plots than transfer functions. The analog input voltage to the A/D is provided by either a linear ramp or by

the discrete output steps of a high resolution DAC. Notice that the error is continuously displayed and includes

the quantization uncertainty of the A/D. For example the error at point 1 of Figure 45 is +1⁄2 LSB because the

digital code appeared 1⁄2 LSB in advance of the center-value of the tread. The error plots always have a

constant negative slope and the abrupt up- side steps are always 1 LSB in magnitude.

Figure 45. Clarifying the Error Specs of an A/D Converter Accuracy=±0 LSB: A Perfect A/D

Figure 46. Clarifying the Error Specs of an A/D Converter Accuracy =±1⁄4 LSB

Submit Documentation Feedback

17

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

Figure 47. Clarifying the Error Specs of an A/D Converter Accuracy = ±1⁄2 LSB

Functional Description

The ADC0801 series contains a circuit equivalent of the 256R network. Analog switches are sequenced by

successive approximation logic to match the analog difference input voltage [V_IN(+) − V_IN(−)] to a corresponding

tap on the R network. The most significant bit is tested first and after 8 comparisons (64 clock cycles) a digital 8-

bit binary code (1111 1111 = full-scale) is transferred to an output latch and then an interrupt is asserted (INTR

makes a high-to-low transition). A conversion in process can be interrupted by issuing a second start command.

The device may be operated in the free-running mode by connecting INTR to the WR input with CS=0. To

ensure start-up under all possible conditions, an external WR pulse is required during the first power-up cycle.

On the high-to-low transition of the WR input the internal SAR latches and the shift register stages are reset. As

long as the CS input and WR input remain low, the A/D will remain in a reset state. Conversion will start from 1

to 8 clock periods after at least one of these inputs makes a low-to-high transition.

A functional diagram of the A/D converter is shown in Figure 48. All of the package pinouts are shown and the

major logic control paths are drawn in heavier weight lines.

The converter is started by having CS and WR simultaneously low. This sets the start flip-flop (F/F) and the

resulting “1” level resets the 8-bit shift register, resets the Interrupt (INTR) F/F and inputs a “1” to the D flop,

F/F1, which is at the input end of the 8-bit shift register. Internal clock signals then transfer this “1” to the Q

output of F/F1. The AND gate, G1, combines this “1” output with a clock signal to provide a reset signal to the

start F/F. If the set signal is no longer present (either WR or CS is a “1”) the start F/F is reset and the 8-bit shift

register then can have the “1” clocked in, which starts the conversion process. If the set signal were to still be

present, this reset pulse would have no effect (both outputs of the start F/F would momentarily be at a “1” level)

and the 8-bit shift register would continue to be held in the reset mode. This logic therefore allows for wide CS

and WR signals and the converter will start after at least one of these signals returns high and the internal clocks

again provide a reset signal for the start F/F.

18

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

(1) CS shown twice for clarity.

(2) SAR = Successive Approximation Register.

Figure 48. Block Diagram

After the “1” is clocked through the 8-bit shift register (which completes the SAR search) it appears as the input

to the D-type latch, LATCH 1. As soon as this “1” is output from the shift register, the AND gate, G2, causes the

new digital word to transfer to the TRI-STATE output latches. When LATCH 1 is subsequently enabled, the Q

output makes a high-to-low transition which causes the INTR F/F to set. An inverting buffer then supplies the

INTR input signal.

Note that this SET control of the INTR F/F remains low for 8 of the external clock periods (as the internal clocks

run at 1/8 of the frequency of the external clock). If the data output is continuously enabled (CS and RD both

held low), the INTR output will still signal the end of conversion (by a high-to-low transition), because the SET

input can control the Q output of the INTR F/F even though the RESET input is constantly at a M "1M " level in

this operating mode. This INTR output will therefore stay low for the duration of the SET signal, which is 8

periods of the external clock frequency (assuming the A/D is not started during this interval).

When operating in the free-running or continuous conversion mode (INTR pin tied to WR and CS wired low – see

Continuous Conversions), the START F/F is SET by the high-to-low transition of the INTR signal. This resets the

SHIFT REGISTER which causes the input to the D-type latch, LATCH 1, to go low. As the latch enable input is

still present, the Q output will go high, which then allows the INTR F/F to be RESET. This reduces the width of

the resulting INTR output pulse to only a few propagation delays (approximately 300 ns).

When data is to be read, the combination of both CS and RD being low will cause the INTR F/F to be reset and

the TRI-STATE output latches will be enabled to provide the 8-bit digital outputs.

Submit Documentation Feedback

19

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

Digital Control Inputs

The digital control inputs (CS, RD, and WR) meet standard T²L logic voltage levels. These signals have been

renamed when compared to the standard A/D Start and Output Enable labels. In addition, these inputs are active

low to allow an easy interface to microprocessor control busses. For non-microprocessor based applications, the

CS input (pin 1) can be grounded and the standard A/D Start function is obtained by an active low pulse applied

at the WR input (pin 3) and the Output Enable function is caused by an active low pull at the RD input (pin 2).

Analog Differential Voltage Inputs and Common-Mode Rejection

This A/D has additional applications flexibility due to the analog differential voltage input. The V_IN(−) input (pin 7)

can be used to automatically subtract a fixed voltage value from the input reading (tare correction). This is also

useful in 4 mA–20 mA current loop conversion. In addition, common-mode noise can be reduced by use of the

differential input.

The time interval between sampling V_IN(+) and V_IN(−) is 4-1/2 clock periods. The maximum error voltage due to

this slight time difference between the input voltage samples is given by:

(1)

Where:

∆V_eis the error voltage due to sampling delay

V_Pis the peak value of the common-mode voltage

f_cmis the common-mode frequency

As an example, to keep this error to 1/4 LSB (∼5 mV) when operating with a 60 Hz common-mode frequency,

f_cm, and using a 640 kHz A/D clock, f_CLK, would allow a peak value of the common-mode voltage, V_P, which is

given by:

(2)

or

(3)

which gives V_P–1.9 V.

The allowed range of analog input voltages usually places more severe restrictions on input common-mode noise

levels.

An analog input voltage with a reduced span and a relatively large zero offset can be handled easily by making

use of the differential input (see Reference Voltage).

Analog Inputs — Input Current

Normal Mode

Due to the internal switching action, displacement currents will flow at the analog inputs. This is due to on-chip

stray capacitance to ground as shown in Figure 49.

20

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

r_ONof SW 1 and SW 2 . 5 kΩ

r=r_ONC_STRAY× 5 kΩ x 12 pF = 60 ns

Figure 49. Analog Input Impedance

The voltage on this capacitance is switched and will result in currents entering the V_IN(+) input pin and leaving

the V_IN(−) input which will depend on the analog differential input voltage levels. These current transients occur

at the leading edge of the internal clocks. They rapidly decay and do not cause errors as the on-chip comparator

is strobed at the end of the clock period.

Fault Mode

If the voltage source applied to the V_IN(+) or V_IN(−) pin exceeds the allowed operating range of V_CC+50 mV, large

input currents can flow through a parasitic diode to the V_CCpin. If these currents can exceed the 1 mA max

allowed spec, an external diode (1N914) should be added to bypass this current to the V_CCpin (with the current

bypassed with this diode, the voltage at the V_IN(+) pin can exceed the V_CCvoltage by the forward voltage of this

diode).

Input Bypass Capacitors

Bypass capacitors at the inputs will average these charges and cause a DC current to flow through the output

resistances of the analog signal sources. This charge pumping action is worse for continuous conversions with

the V_IN(+) input voltage at full-scale. For continuous conversions with a 640 kHz clock frequency with the V_IN(+)

input at 5V, this DC current is at a maximum of approximately 5 µA. Therefore, bypass capacitors should not be

used at the analog inputs or the V_REF/2 pin for high resistance sources (> 1 kΩ). If input bypass capacitors are

necessary for noise filtering and high source resistance is desirable to minimize capacitor size, the detrimental

effects of the voltage drop across this input resistance, which is due to the average value of the input current,

can be eliminated with a full-scale adjustment while the given source resistor and input bypass capacitor are both

in place. This is possible because the average value of the input current is a precise linear function of the

differential input voltage.

Input Source Resistance

Large values of source resistance where an input bypass capacitor is not used, will not cause errors as the input

currents settle out prior to the comparison time. If a low pass filter is required in the system, use a low valued

series resistor (≤ 1 kΩ) for a passive RC section or add an op amp RC active low pass filter. For low source

resistance applications, (≤ 1 kΩ), a 0.1 μF bypass capacitor at the inputs will prevent noise pickup due to series

lead inductance of a long wire. A 100Ω series resistor can be used to isolate this capacitor — both the R and C

are placed outside the feedback loop — from the output of an op amp, if used.

Submit Documentation Feedback

21

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

Noise

The leads to the analog inputs (pins 6 and 7) should be kept as short as possible to minimize input noise

coupling. Both noise and undesired digital clock coupling to these inputs can cause system errors. The source

resistance for these inputs should, in general, be kept below 5 kΩ. Larger values of source resistance can cause

undesired system noise pickup. Input bypass capacitors, placed from the analog inputs to ground, will eliminate

system noise pickup but can create analog scale errors as these capacitors will average the transient input

switching currents of the A/D (see Analog Inputs — Input Current). This scale error depends on both a large

source resistance and the use of an input bypass capacitor. This error can be eliminated by doing a full-scale

adjustment of the A/D (adjust V_REF/2 for a proper full-scale reading — see Full-Scale) with the source resistance

and input bypass capacitor in place.

22

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

Reference Voltage

Span Adjust

For maximum applications flexibility, these A/Ds have been designed to accommodate a 5 V_DC, 2.5 V_DCor an

adjusted voltage reference. This has been achieved in the design of the IC as shown in Figure 50.

Figure 50. The V_REFERENCEDesign on the IC

Notice that the reference voltage for the IC is either 1/2 of the voltage applied to the V_CCsupply pin, or is equal to

the voltage that is externally forced at the V_REF/2 pin. This allows for a ratiometric voltage reference using the

V_CCsupply, a 5 V_DCreference voltage can be used for the V_CCsupply or a voltage less than 2.5 V_DCcan be

applied to the V_REF/2 input for increased application flexibility. The internal gain to the V_REF/2 input is 2, making

the full-scale differential input voltage twice the voltage at pin 9.

An example of the use of an adjusted reference voltage is to accommodate a reduced span — or dynamic

voltage range of the analog input voltage. If the analog input voltage were to range from 0.5 V_DCto 3.5 V_DC

,

instead of 0V to 5 V_DC, the span would be 3V as shown in Figure 51. With 0.5 applied to the V_IN(−) pin to

VDC

absorb the offset, the reference voltage can be made equal to 1/2 of the 3V span or 1.5 VDC. The A/D now will

encode the V_IN(+) signal from 0.5V to 3.5 V with the 0.5V input corresponding to zero and the 3.5 VDC input

corresponding to full-scale. The full 8 bits of resolution are therefore applied over this reduced analog input

voltage range.

Reference Accuracy Requirements

The converter can be operated in a ratiometric mode or an absolute mode. In ratiometric converter applications,

the magnitude of the reference voltage is a factor in both the output of the source transducer and the output of

the A/D converter and therefore cancels out in the final digital output code. The ADC0805 is specified particularly

for use in ratiometric applications with no adjustments required. In absolute conversion applications, both the

initial value and the temperature stability of the reference voltage are important factors in the accuracy of the A/D

converter. For V_REF/2 voltages of 2.4 V_DCnominal value, initial errors of ±10 mV_DCwill cause conversion errors of

±1 LSB due to the gain of 2 of the V_REF/2 input. In reduced span applications, the initial value and the stability of

the V_REF/2 input voltage become even more important. For example, if the span is reduced to 2.5V, the analog

input LSB voltage value is correspondingly reduced from 20 mV (5V span) to 10 mV and 1 LSB at the V_REF/2

input becomes 5 mV. As can be seen, this reduces the allowed initial tolerance of the reference voltage and

requires correspondingly less absolute change with temperature variations. Note that spans smaller than 2.5V

place even tighter requirements on the initial accuracy and stability of the reference source.

Submit Documentation Feedback

23

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

In general, the magnitude of the reference voltage will require an initial adjustment. Errors due to an improper

value of reference voltage appear as full-scale errors in the A/D transfer function. IC voltage regulators may be

used for references if the ambient temperature changes are not excessive. The LM336B 2.5V IC reference diode

(from National Semiconductor) has a temperature stability of 1.8 mV typ (6 mV max) over 0°C≤T_A≤+70°C. Other

temperature range parts are also available.

a) Analog Input Signal Example

*Add if VREF/2 ≤ 1 VDC with LM358 to draw 3 mA to

ground.

b) Accommodating an Analog Input from 0.5V

(Digital Out = 00_HEX) to 3.5 V (Digital Out=FF_HEX

)

Figure 51. Adapting the A/D Analog Input Voltages to Match an Arbitrary Input Signal Range

Errors and Reference Voltage Adjustments

Zero Error

The zero of the A/D does not require adjustment. If the minimum analog input voltage value, V_IN(MIN), is not

ground, a zero offset can be done. The converter can be made to output 0000 0000 digital code for this minimum

input voltage by biasing the A/D V_IN(−) input at this V_IN(MIN) value (see Applications section). This utilizes the

differential mode operation of the A/D.

The zero error of the A/D converter relates to the location of the first riser of the transfer function and can be

measured by grounding the V_IN(−) input and applying a small magnitude positive voltage to the V_IN(+) input. Zero

error is the difference between the actual DC input voltage that is necessary to just cause an output digital code

transition from 0000 0000 to 0000 0001 and the ideal 1/2 LSB value (1/2 LSB = 9.8 mV for V_REF/2=2.500 V_DC).

Full-Scale

The full-scale adjustment can be made by applying a differential input voltage that is 11/2 LSB less than the

desired analog full-scale voltage range and then adjusting the magnitude of the V_REF/2 input (pin 9 or the V_CC

supply if pin 9 is not used) for a digital output code that is just changing from 1111 1110 to 1111 1111.

Adjusting for an Arbitrary Analog Input Voltage Range

If the analog zero voltage of the A/D is shifted away from ground (for example, to accommodate an analog input

signal that does not go to ground) this new zero reference should be properly adjusted first. A V_IN(+) voltage that

equals this desired zero reference plus 1/2 LSB (where the LSB is calculated for the desired analog span, 1

LSB=analog span/256) is applied to pin 6 and the zero reference voltage at pin 7 should then be adjusted to just

obtain the 00_HEXto 01_HEXcode transition.

The full-scale adjustment should then be made (with the proper V_IN(−) voltage applied) by forcing a voltage to the

V_IN(+) input which is given by:

24

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

(4)

where:

V_MAX= The high end of the analog input range and

V_MIN= the low end (the offset zero) of the analog range. (Both are ground referenced.)

The V_REF/2 (or V_CC) voltage is then adjusted to provide a code change from FE_HEXto FF_HEX. This completes the

adjustment procedure

Clocking Option

The clock for the A/D can be derived from the CPU clock or an external RC can be added to provide self-

clocking. The CLK IN (pin 4) makes use of a Schmitt trigger as shown in Figure 52.

1

f

=

CLK

é

ê

ù

ú

æ

ç

è

öæ

÷ç

øè

ö

÷

ø

V - V

V

T

-

+

-

CC

T

RC ln

V - V

V

T

ê

ú

CC

T

ë

û

R @ 10 kΩ

Figure 52. Self-Clocking the A/D

Heavy capacitive or DC loading of the clock R pin should be avoided as this will disturb normal converter

operation. Loads less than 50 pF, such as driving up to 7 A/D converter clock inputs from a single clock R pin of

1 converter, are allowed. For larger clock line loading, a CMOS or low power TTL buffer or PNP input logic

should be used to minimize the loading on the clock R pin (do not use a standard TTL buffer).

Restart During a Conversion

If the A/D is restarted (CS and WR go low and return high) during a conversion, the converter is reset and a new

conversion is started. The output data latch is not updated if the conversion in process is not allowed to be

completed, therefore the data of the previous conversion remains in this latch. The INTR output simply remains

at the “1” level.

Continuous Conversions

For operation in the free-running mode an initializing pulse should be used, following power-up, to ensure circuit

operation. In this application, the CS input is grounded and the WR input is tied to the INTR output. This WR and

INTR node should be momentarily forced to logic low following a power-up cycle to ensure operation.

Driving the Data Bus

This MOS A/D, like MOS microprocessors and memories, will require a bus driver when the total capacitance of

the data bus gets large. Other circuitry, which is tied to the data bus, will add to the total capacitive loading, even

in TRI-STATE (high impedance mode). Backplane bussing also greatly adds to the stray capacitance of the data

bus.

Submit Documentation Feedback

25

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

There are some alternatives available to the designer to handle this problem. Basically, the capacitive loading of

the data bus slows down the response time, even though DC specifications are still met. For systems operating

with a relatively slow CPU clock frequency, more time is available in which to establish proper logic levels on the

bus and therefore higher capacitive loads can be driven (see typical characteristics curves).

At higher CPU clock frequencies time can be extended for I/O reads (and/or writes) by inserting wait states

(8080) or using clock extending circuits (6800).

Finally, if time is short and capacitive loading is high, external bus drivers must be used. These can be TRI-

STATE buffers (low power Schottky such as the DM74LS240 series is recommended) or special higher drive

current products which are designed as bus drivers. High current bipolar bus drivers with PNP inputs are

recommended.

Power Supplies

Noise spikes on the V_CCsupply line can cause conversion errors as the comparator will respond to this noise. A

low inductance tantalum filter capacitor should be used close to the converter V_CCpin and values of 1 µF or

greater are recommended. If an unregulated voltage is available in the system, a separate LM340LAZ-5.0, TO-

92, 5V voltage regu- lator for the converter (and other analog circuitry) will greatly reduce digital noise on the V_CC

supply.

Wiring and Hook-Up Precautions

Standard digital wire wrap sockets are not satisfactory for breadboarding this A/D converter. Sockets on PC

boards can be used and all logic signal wires and leads should be grouped and kept as far away as possible

from the analog signal leads. Exposed leads to the analog inputs can cause undesired digital noise and hum

pickup, therefore shielded leads may be necessary in many applications.

A single point analog ground that is separate from the logic ground points should be used. The power supply

bypass capacitor and the self-clocking capacitor (if used) should both be returned to digital ground. Any V_REF/2

bypass capacitors, analog input filter capacitors, or input signal shielding should be returned to the analog

ground point. A test for proper grounding is to measure the zero error of the A/D converter. Zero errors in excess

of 1/4 LSB can usually be traced to improper board layout and wiring (see Zero Error for measuring the zero

error).

TESTING THE A/D CONVERTER

There are many degrees of complexity associated with test- ing an A/D converter. One of the simplest tests is to

apply a known analog input voltage to the converter and use LEDs to display the resulting digital output code as

shown in Figure 53.

For ease of testing, the V_REF/2 (pin 9) should be supplied with 2.560 V_DCand a V_CCsupply voltage of 5.12 V_DC

should be used. This provides an LSB value of 20 mV.

If a full-scale adjustment is to be made, an analog input voltage of 5.090 V_DC(5.120–1/⁄2 LSB) should be applied

to the V_IN(+) pin with the V_IN(−) pin grounded. The value of the V_REF/2 input voltage should then be adjusted until

the digital output code is just changing from 1111 1110 to 1111 1111. This value of V_REF/2 should then be used

for all the tests.

The digital output LED display can be decoded by dividing the 8 bits into 2 hex characters, the 4 most significant

(MS) and the 4 least significant (LS). Table 2 shows the fractional binary equivalent of these two 4-bit groups. By

adding the voltages obtained from the "VM" and "VLS" columns in Table 2 , the nominal value of the digital

display (when V_REF/2 = 2.560V) can be determined. For example, for an output LED display of 1011 0110 or B6

(in hex), the voltage values from the table are 3.520 + 0.120 or 3.640 V_DC. These voltage values represent the

center-values of a perfect A/D converter. The effects of quantization error have to be accounted for in the

interpretation of the test results.

26

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

Figure 53. Basic A/D Tester

For a higher speed test system, or to obtain plotted data, a digital-to-analog converter is needed for the test set-

up. An accurate 10-bit DAC can serve as the precision voltage source for the A/D. Errors of the A/D under test

can be expressed as either analog voltages or differences in 2 digital words.

A basic A/D tester that uses a DAC and provides the error as an analog output voltage is shown in Figure 52.

The 2 op amps can be eliminated if a lab DVM with a numerical subtraction feature is available to read the

difference voltage, "A–C", directly. The analog input voltage can be supplied by a low frequency ramp generator

and an X-Y plotter can be used to provide analog error (Y axis) versus analog input (X axis).

For operation with a microprocessor or a computer-based test system, it is more convenient to present the errors

digitally. This can be done with the circuit of Figure 55, where the output code transitions can be detected as the

10-bit DAC is incremented. This provides 1⁄4 LSB steps for the 8-bit A/D under test. If the results of this test are

automatically plotted with the analog input on the X axis and the error (in LSB’s) as the Y axis, a useful transfer

function of the A/D under test results. For acceptance testing, the plot is not necessary and the testing speed can

be increased by establishing internal limits on the allowed error for each code.

MICROPROCESSOR INTERFACING

To dicuss the interface with 8080A and 6800 microprocessors, a common sample subroutine structure is used.

The microprocessor starts the A/D, reads and stores the results of 16 successive conversions, then returns to the

user’s program. The 16 data bytes are stored in 16 successive memory locations. All Data and Addresses will be

given in hexadecimal form. Software and hardware details are pro- vided separately for each type of

microprocessor.

Interfacing 8080 Microprocessor Derivatives (8048, 8085)

This converter has been designed to directly interface with derivatives of the 8080 microprocessor. The A/D can

be mapped into memory space (using standard memory address decoding for CS and the MEMR and MEMW

strobes) or it can be controlled as an I/O device by using the I/O R and I/O W strobes and decoding the address

bits A0 → A7 (or address bits A8 → A15 as they will contain the same 8-bit address information) to obtain the

CS input. Using the I/O space provides 256 additional addresses and may allow a simpler 8-bit address decoder

but the data can only be input to the accumulator. To make use of the additional memory reference instructions,

the A/D should be mapped into memory space. An example of an A/D in I/O space is shown in Figure 56.

Submit Documentation Feedback

27

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

Figure 54. A/D Tester with Analog Error Output

Figure 55. Basic “Digital” A/D Tester

Table 2. Decoding the Digital Output LEDs

OUTPUT VOLTAGE CENTER VALUES

WITH V_REF/2=2.560 V_DC

VMS GROUP⁽¹⁾

FRACTIONAL BINARY VALUE FOR

HEX

BINARY

MS GROUP

LS GROUP

VLS GROUP⁽¹⁾

0.300

0.280

0.260

0.240

0.220

0.200

0.180

0.160

0.140

0.120

0.100

0.080

0.060

0.040

0.020

0

F

E

D

C

B

A

9

8

7

6

5

4

3

2

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

15/16

13/16

11/16

9/16

7/16

5/16

163

15/256

13/256

11/256

9/256

7/256

2/256

3/256

1/256

4.800

4.480

4.160

3.840

3.520

3.200

2.880

2.560

2.240

1.920

1.600

1.280

0.960

0.640

0.320

0

7/8

5/8

3/8

1/8

7/128

3/4

3/64

5/128

3/128

1/128

1/2

1/32

1/4

1/64

1/16

(1) Display Output=VMS Group + VLS Group

28

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

(1) *Pin numbers for the DP8228 system controller, others are INS8080A

(2) Pin 23 of the INS8228 must be tied to +12V through a 1 kΩ resistor to generate the RST 7 instruction when an

interrupt is acknowledged as required by the accompanying sample program.

Figure 56. ADC0801_INS8080A CPU Interface

Submit Documentation Feedback

29

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

SAMPLE PROGRAM FOR Figure 56 ADC0801–INS8080A CPU INTERFACE

Note: The stack pointer must be dimensioned because a RST 7 instruction pushes the PC onto the stack.

Note: All address used were arbitrarily chosen.

The standard control bus signals of the 8080 CS, RD and WR) can be directly wired to the digital control inputs

of the A/D and the bus timing requirements are met to allow both starting the converter and outputting the data

onto the data bus. A bus driver should be used for larger microprocessor systems where the data bus leaves the

PC board and/or must drive capacitive loads larger than 100 pF.

Sample 8080A CPU Interfacing Circuitry and Program

The following sample program and associated hardware shown in Figure 56 may be used to input data from the

converter to the INS8080A CPU chip set (comprised of the INS8080A microprocessor, the INS8228 system

controller and the INS8224 clock generator). For simplicity, the A/D is controlled as an I/O device, specifically an

8-bit bi-directional port located at an arbitrarily chosen port address, E0. The TRI-STATE output capability of the

A/D eliminates the need for a peripheral interface device, however address decoding is still required to generate

the appropriate CS for the converter.

It is important to note that in systems where the A/D converter is 1-of-8 or less I/O mapped devices, no address

decoding circuitry is necessary. Each of the 8 address bits (A0 to A7) can be directly used as CS inputs — one

for each I/O device.

INS8048 Interface

The INS8048 interface technique with the ADC0801 series (see Figure 57) is simpler than the 8080A CPU

interface. There are 24 I/O lines and three test input lines in the 8048. With these extra I/O lines available, one of

the I/O lines (bit 0 of port 1) is used as the chip select signal to the A/D, thus eliminating the use of an external

address decoder. Bus control signals RD, WR and INT of the 8048 are tied directly to the A/D. The 16 converted

data words are stored at on-chip RAM locations from 20 to 2F (Hex). The RD and WR signals are generated by

reading from and writing into a dummy address, respectively. A sample interface program is shown below.

30

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

Figure 57. INS8048 Interface

SAMPLE PROGRAM FOR Figure 57 INS8048 INTERFACE

Interfacing the Z-80

The Z-80 control bus is slightly different from that of the 8080. General RD and WR strobes are provided and

separate memory request, MREQ, and I/O request, IORQ, signals are used which have to be combined with the

generalized strobes to provide the equivalent 8080 signals. An advantage of operating the A/D in I/O space with

the Z-80 is that the CPU will automatically insert one wait state (the RD and WR strobes are extended one clock

period) to allow more time for the I/O devices to respond. Logic to map the A/D in I/O space is shown in

Figure 58.

Figure 58. Mapping the A/D as an I/O Device for Use with the Z-80 CPU

Additional I/O advantages exist as software DMA routines are available and use can be made of the output data

transfer which exists on the upper 8 address lines (A8 to A15) during I/O input instructions. For example, MUX

channel selection for the A/D can be accomplished with this operating mode.

Submit Documentation Feedback

31

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

Interfacing 6800 Microprocessor Derivatives (6502, etc.)

The control bus for the 6800 microprocessor derivatives does not use the RD and WR strobe signals. Instead it

employs a single R/W line and additional timing, if needed, can be derived from the φ2 clock. All I/O devices are

memory mapped in the 6800 system, and a special signal, VMA, indicates that the current address is valid.

Figure 59 shows an interface schematic where the A/D is memory mapped in the 6800 system. For simplicity,

the CS decoding is shown using 1/2 DM8092. Note that in many 6800 systems, an already decoded 4/5 line is

brought out to the common bus at pin 21. This can be tied directly to the CS pin of the A/D, provided that no

other devices are addressed at HX ADDR: 4XXX or 5XXX.

The following subroutine performs essentially the same function as in the case of the 8080A interface and it can

be called from anywhere in the user’s program.

In Figure 60 the ADC0801 series is interfaced to the M6800 microprocessor through (the arbitrarily chosen) Port

B of the MC6820 or MC6821 Peripheral Interface Adapter, (PIA).

Here the CS pin of the A/D is grounded since the PIA is already memory mapped in the M6800 system and no

CS decoding is necessary. Also notice that the A/D output data lines are connected to the microprocessor bus

under program control through the PIA and therefore the A/D RD pin can be grounded.

A sample interface program equivalent to the previous one is shown below Figure 60. The PIA Data and Control

Registers of Port B are located at HEX addresses 8006 and 8007, respectively.

GENERAL APPLICATIONS

The following applications show some interesting uses for the A/D. The fact that one particular microprocessor is

used is not meant to be restrictive. Each of these application circuits would have its counterpart using any

microprocessor that is desired.

Multiple ADC0801 Series to MC6800 CPU Interface

To transfer analog data from several channels to a single microprocessor system, a multiple converter scheme

presents several advantages over the conventional multiplexer single-converter approach. With the ADC0801

series, the differential inputs allow individual span adjustment for each channel. Furthermore, all analog input

channels are sensed simultaneously, which essentially divides the microproces- sor’s total system servicing time

by the number of channels, since all conversions occur simultaneously. This scheme is shown in Figure 61.

*Numbers in parentheses refer to MC6800 CPU pin out.

**Number or letters in brackets refer to standard M6800 system common bus code.

Figure 59. ADC0801-MC6800 CPU Interface

32

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

SAMPLE PROGRAM FOR Figure 59 ADC0801-MC6800 CPU INTERFACE

In order for the microprocessor to service subroutines and inter- rupts, the stack pointer must be

dimensioned in the user’s program.

Figure 60. ADC0801–MC6820 PIA Interface

Submit Documentation Feedback

33

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

SAMPLE PROGRAM FOR Figure 60 ADC0801–MC6820 PIA INTERFACE

The following schematic and sample subroutine (DATA IN) may be used to interface (up to) 8 ADC0801’s directly

to the MC6800 CPU. This scheme can easily be extended to allow the interface of more converters. In this

configuration the converters are (arbitrarily) located at HEX address 5000 in the MC6800 memory space. To

save components, the clock signal is derived from just one RC pair on the first converter. This output drives the

other A/Ds.

All the converters are started simultaneously with a STORE instruction at HEX address 5000. Note that any other

HEX address of the form 5XXX will be decoded by the circuit, pulling all the CS inputs low. This can easily be

avoided by using a more definitive address decoding scheme. All the interrupts are ORed together to insure that

all A/Ds have completed their conversion before the microprocessor is interrupted.

The subroutine, DATA IN, may be called from anywhere in the user’s program. Once called, this routine

initializes the CPU, starts all the converters simultaneously and waits for the interrupt signal. Upon receiving the

interrupt, it reads the converters (from HEX addresses 5000 through 5007) and stores the data successively at

(arbitrarily chosen) HEX addresses 0200 to 0207, before returning to the user’s pro- gram. All CPU registers then

recover the original data they had before servicing DATA IN.

Auto-Zeroed Differential Transducer Amplifier and A/D Converter

The differential inputs of the ADC0801 series eliminate the need to perform a differential to single ended

conversion for a differential transducer. Thus, one op amp can be eliminated since the differential to single ended

conversion is provided by the differential input of the ADC0801 series. In general, a transducer preamp is

required to take advantage of the full A/D converter input dynamic range.

34

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

*Numbers in parentheses refer to MC6800 CPU pin out.

**Numbers of letters in brackets refer to standard M6800 system common bus code.

Figure 61. Interfacing Multiple A/Ds in an MC6800 System

Submit Documentation Feedback

35

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

SAMPLE PROGRAM FOR Figure 61 INTERFACING MULTIPLE A/D’s IN AN MC6800 SYSTEM

Note: In order for the microprocessor to service subroutines and interrupts, the stack pointer must be

dimensioned in the user’s program.

For amplification of DC input signals, a major system error is the input offset voltage of the amplifiers used for

the preamp. Figure 62 is a gain of 100 differential preamp whose offset voltage errors will be cancelled by a

zeroing subroutine which is performed by the INS8080A microprocessor system. The total allowable input offset

voltage error for this preamp is only 50 µV for /⁄4 LSB error. This would obviously require very precise amplifiers.

The expression for the differential output voltage of the preamp is:

36

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

R2 = 49.5 R1

Switches are LMC13334 CMOS analog switches.

The 9 resistors used in the auto-zero section can be ±5% tolerance.

Figure 62. Gain of 100 Differential Transducer Preamp

(5)

where I_Xis the current through resistor R_X. All of the offset error terms can be cancelled by making ±I_XR_X= V_OS1

+ V_OS3− V_OS2. This is the principle of this auto-zeroing scheme.

The INS8080A uses the 3 I/O ports of an INS8255 Programable Peripheral Interface (PPI) to control the auto

zeroing and input data from the ADC0801 as shown in Figure 63. The PPI is programmed for basic I/O operation

(mode 0) with Port A being an input port and Ports B and C being output ports. Two bits of Port C are used to

alternately open or close the 2 switches at the input of the preamp. Switch SW1 is closed to force the preamp’s

differential input to be zero during the zeroing subroutine and then opened and SW2 is then closed for

conversion of the actual differential input signal. Using 2 switches in this manner eliminates concern for the ON

resistance of the switches as they must conduct only the input bias current of the input amplifiers.

Output Port B is used as a successive approximation register by the 8080 and the binary scaled resistors in

series with each output bit create a D/A converter. During the zeroing subroutine, the voltage at V_xincreases or

decreases as required to make the differential output voltage equal to zero. This is accomplished by ensuring

that the voltage at the output of A1 is approximately 2.5V so that a logic "1" (5V) on any output of Port B will

source current into node V_Xthus raising the voltage at V_Xand making the output differential more negative.

Conversely, a logic "0" (0V) will pull current out of node V_Xand decrease the voltage, causing the differential

output to become more positive. For the resistor values shown, V_Xcan move ±12 mV with a resolution of 50 µV,

which will null the offset error term to /⁄4 LSB of full-scale for the ADC0801. It is important that the voltage levels

that drive the auto-zero resistors be constant. Also, for symmetry, a logic swing of 0V to 5V is convenient. To

achieve this, a CMOS buffer is used for the logic output signals of Port B and this CMOS package is powered

with a stable 5V source. Buffer amplifier A1 is necessary so that it can source or sink the D/A output current.

Submit Documentation Feedback

37

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

Figure 63. Microprocessor Interface Circuitry for Differential Preamp

A flow chart for the zeroing subroutine is shown in Figure 64. It must be noted that the ADC0801 series will

output an all zero code when it converts a negative input [V_IN(−) ≥ V_IN(+)]. Also, a logic inversion exists as all of

the I/O ports are buffered with inverting gates.

Basically, if the data read is zero, the differential output voltage is negative, so a bit in Port B is cleared to pull VX

more negative which will make the output more positive for the next conversion. If the data read is not zero, the

output voltage is positive so a bit in Port B is set to make VX more positive and the output more negative. This

continues for 8 approximations and the differential output eventually converges to within 5 mV of zero.

The actual program is given in Figure 65. All addresses used are compatible with the BLC 80/10 microcomputer

system. In particular:

•

Port A and the ADC0801 are at port address E4

Port B is at port address E5

Port C is at port address E6

PPI control word port is at port address E7

Program Counter automatically goes to ADDR:3C3D upon acknowledgment of an interrupt from the ADC0801

Multiple A/D Converters in a Z-80 Interrupt Driven Mode

In data acquisition systems where more than one A/D converter (or other peripheral device) will be interrupting

pro- gram execution of a microprocessor, there is obviously a need for the CPU to determine which device

requires servicing. Figure 66 and the accompanying software is a method of determining which of 7 ADC0801

converters has completed a conversion (INTR asserted) and is requesting an interrupt. This circuit allows starting

the A/D converters in any sequence, but will input and store valid data from the converters with a priority

sequence of A/D 1 being read first, A/D 2 second, etc., through A/D 7 which would have the lowest priority for

data being read. Only the converters whose INT is asserted will be read.

38

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

The key to decoding circuitry is the DM74LS373, 8-bit D type flip-flop. When the Z-80 acknowledges the

interrupt, the program is vectored to a data input Z-80 subroutine. This subroutine will read a peripheral status

word from the DM74LS373 which contains the logic state of the INTR outputs of all the converters. Each

converter which initiates an interrupt will place a logic "0" in a unique bit position in the status word and the

subroutine will determine the identity of the converter and execute a data read. An identifier word (which

indicates which A/D the data came from) is stored in the next sequential memory location above the location of

the data so the program can keep track of the identity of the data entered.

Figure 64. Flow Chart for Auto-Zero Routine

Submit Documentation Feedback

39

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

www.ti.com

NOTE: All numerical values are hexadecimal representations.

Figure 65. Software for Auto-Zeroed Differential A/D

The following notes apply:

•

It is assumed that the CPU automatically performs a RST 7 instruction when a valid interrupt is acknowledged

(CPU is in interrupt mode 1). Hence, the subroutine starting address of X0038.

•

The address bus from the Z-80 and the data bus to the Z-80 are assumed to be inverted by bus drivers.

A/D data and identifying words will be stored in sequential memory locations starting at the arbitrarily chosen

address X 3E00.

•

The stack pointer must be dimensioned in the main program as the RST 7 instruction automatically pushes

the PC onto the stack and the subroutine uses an additional 6 stack addresses.

The peripherals of concern are mapped into I/O space with the following port assignments:

HEX PORT ADDRESS

PERIPHERAL

HEX PORT ADDRESS

PERIPHERAL

A/D 4

00

01

02

03

MM74C374 8-bit flip-flop

04

05

06

07

A/D 1

A/D 2

A/D 3

A/D 5

A/D 6

A/D 7

40

Submit Documentation Feedback

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

ADC0801, ADC0802

ADC0803, ADC0804, ADC0805

www.ti.com

SNOSBI1B –NOVEMBER 2009–REVISED FEBRUARY 2013

This port address also serves as the A/D identifying word in the program.

Figure 66. Multiple A/Ds with Z-80 Type Microprocessor

Submit Documentation Feedback

41

Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805

PACKAGE MATERIALS INFORMATION

www.ti.com

26-Mar-2013

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device

Package Package Pins

Type Drawing

SPQ

Reel

A0

B0

K0

P1

W

Pin1

Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant

(mm) W1 (mm)

ADC0804LCWMX

SOIC

DW

20

1000

330.0

24.4

10.9

13.3

3.25

12.0

24.0

Q1

ADC0804LCWMX/NOPB

Pack Materials-Page 1

PACKAGE MATERIALS INFORMATION

www.ti.com

26-Mar-2013

*All dimensions are nominal

Device

Package Type Package Drawing Pins

SPQ

Length (mm) Width (mm) Height (mm)

ADC0804LCWMX

SOIC

DW

20

1000

367.0

45.0

ADC0804LCWMX/NOPB

Pack Materials-Page 2

MECHANICAL DATA

NFH0020A

N0020A

N20A (Rev G)

www.ti.com

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products

Applications

Audio

www.ti.com/audio

amplifier.ti.com

dataconverter.ti.com

www.dlp.com

Automotive and Transportation www.ti.com/automotive

Communications and Telecom www.ti.com/communications

Amplifiers

Data Converters

DLP® Products

DSP

Computers and Peripherals

Consumer Electronics

Energy and Lighting

Industrial

www.ti.com/computers

www.ti.com/consumer-apps

www.ti.com/energy

dsp.ti.com

Clocks and Timers

Interface

www.ti.com/clocks

interface.ti.com

logic.ti.com

www.ti.com/industrial

www.ti.com/medical

Medical

Logic

Security

www.ti.com/security

Power Mgmt

Microcontrollers

RFID

power.ti.com

Space, Avionics and Defense

Video and Imaging

www.ti.com/space-avionics-defense

www.ti.com/video

microcontroller.ti.com

www.ti-rfid.com

www.ti.com/omap

OMAP Applications Processors

Wireless Connectivity

TI E2E Community

e2e.ti.com

www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265


型号：	ADC0804LCWM
厂家：	TEXAS INSTRUMENTS
描述：	8-Bit muP Compatible A/D Converters 8位MUP兼容A / D转换器转换器光电二极管
文件：	总48页 (文件大小：3734K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

ADC0804LCWM [TI]

相关型号：

ADC0804LCWM/NOPB

ADC0804LCWM96

ADC0804LCWMX

ADC0804LCWMX/NOPB

ADC0804S030

ADC0804S030

ADC0804S030TS

ADC0804S030TS

ADC0804S030TS/C1,1

ADC0804S040

ADC0804S040TS

ADC0804S040TS