74F132SJCX [TI]
F/FAST SERIES, QUAD 2-INPUT NAND GATE, PDSO14, 0.300 INCH, EIAJ, PLASTIC, SOIC-14;
| 型号： | 74F132SJCX |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | F/FAST SERIES, QUAD 2-INPUT NAND GATE, PDSO14, 0.300 INCH, EIAJ, PLASTIC, SOIC-14 触发器 |
| 文件： | 总10页 (文件大小：360K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
54F132,74F132
Quad 2-Input NAND Schmitt Trigger
Literature Number: SNOS151A
November 1994
54F/74F132
Quad 2-Input NAND Schmitt Trigger
threshold voltages for positive and negative-going transi-
tions. This hysteresis between the positive-going and
negative-going input threshold (typically 800 mV) is deter-
mined by resistor ratios and is essentially insensitive to tem-
perature and supply voltage variations.
General Description
The ’F132 contains four 2-input NAND gates which accept
standard TTL input signals and provide standard TTL output
levels. They are capable of transforming slowly changing in-
put signals into sharply defined, jitter-free output signals. In
addition, they have a greater noise margin than conventional
NAND gates.
Features
n Guaranteed 4000V mimum ESD n
n Standard Military DrawMD)
n 5962-89487
Each circuit contains a 2-input Schmitt trigger followed by
level shifting circuitry and a standard FAST® output struc-
ture. The Schmitt trigger uses positive feedback to effectively
speed-up slow input transitions, and provide different input
Ordering Code: See Section 0
DSXXX
Commercial
Military
Package
Number
N14A
kage Dcription
74F132PC
14-L(0.300de) ded Dual-In-Line
14-Lead ramic Dual-In-Line
54F132DM (Note 2)
J14A
74F132SC (Note 1)
74F132SJ (Note 1)
M14A
ead (0." Wide) Molded Small Outline, JEDEC
(0.300Wide) Molded Small Outline, EIAJ
Cerpack
M14
54F132FM (Note 2)
54F132LM (Note 2)
W14
E20A
Ceramic Leadless Chip Carrier, Type C
=
Note 1: Devices also available in 13" reel. Use suffix X and SJX.
=
Note 2: Military grade device with environmental and rn-in procese suffix DMQB, FMQB and LMQB.
Logic Symbol
EEE/IEC
DS009477-3
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
© 1997 National Semiconductor Corporation
DS009477
www.national.com
1
PrintDate=1997/08/28 PrintTime=12:25:28 10193 ds009477 Rev. No. 1 cmserv Proof
1
Connection Diagrams
Pin Assignment for
DIP, SOIC and Flatpak
Pin Assignment
for LCC
DS009477-1
Unit Loading/Fan Out See Section 0 for U.L. definitions
DSXXX
54F/74F
Pin Names
Description
U.L.
HIGH/LOW
1.0/1.0
Input IIH/IIL
Output IOH/I
20 µA/−0.6
−1 mA/20
An, Bn
On
Inputs
Outputs
50/33.3
Function Table
Inputs
Outputs
A
L
B
L
O
H
H
H
L
L
H
L
H
H
H
=
=
H
L
HIGH Voltage Level
LOW Voltage Level
www.national.com
2
PrintDate=1997/08/28 PrintTime=12:25:31 10193 ds009477 Rev. No. 1 cmserv Proof
2
Absolute Maximum Ratings (Note 3)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Current Applied to Output
in LOW State (Max)
twice the rated IOL (mA)
4000V
ESD Last Passing Voltage (Min)
Recommended Operating
Conditions
Free Air Ambient Temperature
Military
Storage Temperature
Ambient Temperature under Bias
Junction Temperature under Bias
Plastic
−65˚C to +150˚C
−55˚C to +125˚C
−55˚C to +175˚C
−55˚C to +150˚C
−55˚C to +125˚C
0˚C to +70˚C
VCC Pin Potential to
Ground Pin
Commercial
−0.5V to +7.0V
−0.5V to +7.0V
Supply Voltage
Military
Input Voltage (Note 4)
Input Current (Note 4)
Voltage Applied to Output
+4.5V to +5.5V
o +5.5V
−30 mA to +5.0 mA
Commercial
Note 3: Absolute maximum ratings are values beyoe may
be damaged or have its useful life impaired. Functioder thee
conditions is not implied.
=
in HIGH State (with VCC 0V)
Standard Output
TRI-STATE® Output
−0.5V to VCC
Note 4: Either voltage limit or culimit s suffictect inputs.
−0.5V to +5.5V
DC Electrical Characteristics
Symbol
Parameter
54F/74F
Typ
Units
oitions
Min
1.5
0.7
0.4
Max
2.0
VT+
VT−
∆VT
VCD
VOH
Positive-going Threshold
Negative-going Threshold
V
V
V
.0
5.0
5.0
Min
1
+
−
Hysteresis (VT − VT
)
=
IIN −18 mA
Input Clamp Diode Voltage
−1.2
=
IOH −1 mA
Output HIGH
Voltage
54F 10% VCC
2.5
2.5
2.7
=
IOH −1 mA
74F 10% VCC
74F 5% VCC
54F 10% VCC
74F 10% VCC
54F
V
V
Min
Min
Max
Max
Max
0.0
=
IOH −1 mA
=
IOL 20 mA
VOL
Output LOW
Voltage
20.0
5.0
100
7.0
250
50
=
IOL 20 mA
=
VIN 2.7V
IIH
Input HIGH
µA
µA
µA
V
Current
74F
=
VIN 7.0V
IBVI
ICEX
VID
IOD
Input HIGH Current
Breakdown Test
Output HIGH
Leakage Current
Input Lea
Te
54F
74F
=
VOUT VCC
5
=
7
4.75
−60
IID 1.9 µA
All Other Pins Grounded
=
74F
3.75
µA
0.0
VIOD 150 mV
All Other Pins Grounded
=
VIN 0.5V
IIL
−0.6
−150
17.0
18.0
mA
mA
mA
mA
Max
Max
Max
Max
=
VOUT 0V
IOS
ICCH
ICCL
nt
Po
Power nt
=
VO HIGH
=
VO LOW
3
www.national.com
PrintDate=1997/08/28 PrintTime=12:25:38 10193 ds009477 Rev. No. 1 cmserv Proof
3
AC Electrical Characteristics
See Section 0 for Waveforms and Load Configurations
DSXXX
74F
54F
74F
=
=
=
TA +25˚C
TA, VCC Mil
TA, VCC Com
Fig.
No.
=
=
=
Symbol
Parameter
VCC +5.0V
CL 50 pF
CL 50 pF
Units
=
CL 50 pF
Min
4.0
5.0
Typ
Max
10.5
12.5
Min
Max
13.0
16.0
Min
Max
12.0
13.0
tPLH
tPHL
Propagation Delay
An, Bn to On
2.0
4.5
3.5
5.0
kk
-kk
DSXXX
ns
Ordering Information
The device number is used to form part of a simplified purchasing code where the package type anrange are de-
fined as follows:
Book
Extract
End
DS009477-5
www.national.com
4
PrintDate=1997/08/28 PrintTime=12:25:40 10193 ds009477 Rev. No. 1 cmserv Proof
4
Physical Dimensions inches (millimeters) unless otherwise noted
20-Lead Ceramic Lear (L)
NS Package
14-Lead Ceramic Dual-In-Line Package (D)
NS Package Number J14A
5
www.national.com
PrintDate=1997/08/28 PrintTime=12:25:42 10193 ds009477 Rev. No. 1 cmserv Proof
5
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
14-Lead (0.150" Wide) MoOutlinackage, JEDEC (S)
NS Pr M14A
14-Lead (0.300" Wide) Molded Small Outline Package, EIAJ (SJ)
NS Package Number M14D
www.national.com
6
PrintDate=1997/08/28 PrintTime=12:25:43 10193 ds009477 Rev. No. 1 cmserv Proof
6
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
14-Lead (0.300" Wide) (MoldPacka(P)
NS Package
14-Lead Ceramic Flatpak (F)
NS Package Number W14B
7
www.national.com
PrintDate=1997/08/28 PrintTime=12:25:43 10193 ds009477 Rev. No. 1 cmserv Proof
7
Y
S ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE-
VITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMI-
CORATION. As used herein:
1. Life ices or systems are devices or sys-
tems which, (a) are intended for surgical implant into
the body, or (b) support or sustain life, and whose fail-
ure to perform when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
2. A critical component in any component of a life support
device or system whose failure to perform can be rea-
sonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
National Semiconductor
Corporation
National Semiconductor
Europe
National Semiconductor
Hong Kong Ltd.
National Semiconductor
Japan Ltd.
Americas
Fax: +49 (0) 1 80-530 85 86
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
Tel: 81-3-5620-6175
Fax: 81-3-5620-6179
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
8
PrintDate=1997/08/28 PrintTime=12:25:44 10193 ds009477 Rev. No. 1 cmserv Proof
8
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Medical
Security
Logic
Space, Avionics and Defense www.ti.com/space-avionics-defense
Transportation and Automotive www.ti.com/automotive
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明