AT-259RTR [TE]
Voltage Variable Absorptive Attenuator DC - 2 GHz; 可变电压衰减器吸收DC - 2 GHz的型号: | AT-259RTR |
厂家: | TE CONNECTIVITY |
描述: | Voltage Variable Absorptive Attenuator DC - 2 GHz |
文件: | 总2页 (文件大小:115K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
VoltageVariable Absorptive Attenuator
DC - 2 GHz
AT-259
V 2.00
SOT-143
Features
● Attenuation: 12 dB at 1 GHz
● Low Intermodulation Products
● Low DC Power Consumption: 50 µW
● Single Voltage Control 0 to -4 Volts
● Nanosecond Switching Speed
● Temperature Range: -40˚C to + 85˚C
● Low Cost SOT/143 Plastic Package
1
● Tape and Reel Packaging Available
Description
M/A-COM’s AT-259 is a GaAs MMIC voltage variable absorp-
tive attenuator in a low cost SOT/143 4-Lead surface mount
plastic package. The AT-259 is ideally suited for use where
attenuation fine tuning, fast switching and very low power
consumption are required. Typical applications include radio,
cellular, GPS equipment and other Automatic Gain/Level
Control circuits.
The AT-259 is fabricated with a monolithic GaAs MMIC using
a mature 1 micron process. The process features full chip pas-
sivation for increased performance and reliability.
Ordering Information
Part Number
Package
AT-259 PIN
SOT 4-Lead Plastic Package
Forward Tape & Reel
AT-259TR
AT-259RTR
Reverse Tape & Reel
Electrical Specifications, TA = +25°C
Parameter
Insertion Loss
Test Conditions2
Unit
Min.
Typ.
2.9
3.0
3.2
3.4
± 0.2
± 2.3
± 7.0
2.1:1
Max
3.1
3.2
3.5
3.8
± 0.4
± 2.5
± 7.5
DC – 0.1 GHz
DC – 0.5 GHz
DC – 1.0 GHz
dB
dB
dB
dB
dB
dB
dB
DC – 2.0 GHz
Flatness
(Peak to Peak)
DC – 2.0 GHz
5 dB Attenuation
10 dB Attenuation
15 dB Attenuation
VSWR
Trise, Tfall
Ton, Toff
Transients
10% to 90% RF, 90% to 10% RF
50% Control to 90% RF, 50% Control to 10% RF
In Band
nS
nS
mV
3
5
10
Power
Handling
Linear Operation
Absolute Max.Input Power
dBm
dBm
13
21
Measured Relative
to Input Power
0.05 GHz
0.5 – 2.0 GHz
34
47
IP
2
dBm
(For two-tone Input Power Up to +5 dBm)
Measured Relative
to Input Power
0.05 GHz
0.5 – 2.0 GHz
dBm
dBm
18
18.5
31(3)
36(3)
IP
3
(For two-tone Input Power Up to +5 dBm)
1. Refer to “Tape and Reel Packaging”Section, or contact factory.
2. All measurements at 1 GHz in a 50Wsystem, unless otherwise specified.A control voltage 0 to -4 volts @ 20 µA typ.
3. For levels above 6 dB attenuation. For levels below 6 dB, the minimum specification numbers apply.
V 2.00
Absolute Maximum Ratings1
Functional Schematic
Parameter
Absolute Maximum
4
3
Max. Input Power
+21 dBm
Control Voltage
+5 V, -8.5 V
Operating Temperature
Storage Temperature
-40°C to +85°C
-65°C to +150°C
1.Operation of this device above any one of these parameters may cause per-
manent damage
Pin Configuration
1
2
Pin No.
Description
GND
A
1
2
3
4
RF2
RF1
Typical Performance
相关型号:
©2020 ICPDF网 联系我们和版权申明