313053-1 [TE]
Crimping Die Assembly;型号: | 313053-1 |
厂家: | TE CONNECTIVITY |
描述: | Crimping Die Assembly |
文件: | 总5页 (文件大小:408K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Instruction Sheet
408-9167
Crimping Die Assembly 58212-1
27 MAY 15 Rev B
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low
volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Stationary Die
Center
Contact
Crimpers
Ferrule
Crimping Area
Movable Die
Locator
Die Holding Screw
Figure 1
1. INTRODUCTION
This instruction sheet covers the use of Crimping Die Assembly 58212-1 which is used to crimp Size 8 straight
pin and socket coaxial contacts.
The die assembly is used in Hand Crimping Tool 69710-1. Refer to Instruction Sheet 408-2095 packaged with
the hand tool for information concerning die installation and general performance of the tool.
Read these instructions carefully before using the dies.
NOTE
All dimensions on this sheet are in metric units [with U.S. customary units in brackets.] Figures and illustrations are for
reference only and are not drawn to scale.
Reasons for reissue of this document are provided in Section 6, REVISION SUMMARY.
2. DESCRIPTION (Figure 1)
The die assembly consists of a stationary die, a movable die, and a locator. The die assembly features two
crimping areas. One to crimp the center contact and one to crimp the ferrule.
3. CRIMPING PROCEDURE
Refer to the table in Figure 2 and select the appropriate cable and connector. Strip the cable to the length
indicated in Figure 2.
Refer to Figure 3 and proceed as follows:
3.1. Center Contact
1. Slide the ferrule over the cable.
2. Flare the braided cable so that it will slide easily onto the back of the pin or socket contact body.
3. Insert center conductor into the contact, making sure conductor is FULLY seated in the contact.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com.
© 2015 TE Connectivity family of companies
All Rights Reserved
*Trademark
PRODUCT INFORMATION 1-800-522-6752
1 of 5
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
408-9167
Pin Connector
Support Sleeve
Connector Body
Socket Connector
10.31 ±0.41
[.406 ±.016]
Ferrule
3.58 ±0.41
[.141 ±.016]
4.78 ±0.41
[.188 ±.016]
Cable Strip Lengths
CONNECTOR
CABLE (RG/U)
HAND TOOL
PIN
SOCKET
228618-4
228596-4
142, 142A, 142B
69710-1
221980-2●
221981-2●
●50-Ohm Connector
Figure 2
Center-Contact Crimp
Ferrule Crimp
Front of Die
Ferrule
Stationary
Indenter
Locator
Ferrule
Crimping
Area
Braid
Cable
Cable
Ferrule Shoulder
Movable
Indenter
Center Contact
Crimping Area
Figure 3
4. Insert contact and cable into the dies so that stationary die indenter (crimper) starts entering the
crimping port of the contact. Visually align the other contact port hole over the movable die indenter
(crimper).
NOTE
Squeeze handles slowly until movable die indenter (crimper) enters crimping port.
5. Holding cable in place, actuate tool through a complete cycle.
6. Remove the crimped center contact from the tool.
3.2. Ferrule
1. Slide the ferrule over the two port holes of the contact until ferrule bottoms on connector body.
2. Insert the connector body into the front of the die assembly and into the locator, making sure locator
enters area between shoulder and spring of connector body. See Figure 3.
2 of 5
Rev B
408-9167
3. Holding the connector body and ferrule in place, actuate the tool through a complete cycle.
NOTE
Apply sufficient pressure on cable so shoulder on the connector body maintains contact against locator as shown in Figure 3.
4. Remove the crimped connector from the tool.
4. MAINTENANCE AND INSPECTION PROCEDURE
4.1. Daily Maintenance
TE Connectivity recommends that each operator of the dies be made aware of, and responsible for, the
following steps of daily maintenance:
1. Remove dust, moisture, and other contaminants with a clean brush, or a soft, lint-free cloth. Do not
use objects that could damage the dies.
2. Make sure the proper die holding screws are in place and secured with the proper retaining rings.
Check die alignment and tighten die holding screws at least twice daily.
3. Make certain all surfaces are protected with a THIN coat of any good SAE 20 motor oil. Do not oil
excessively.
4. When the dies are not in use, mate and store them in a clean, dry area.
4.2. Inspection
Regular inspections should be performed by quality control personnel. A record of scheduled inspections
should remain with the dies and/or be supplied to supervisory personnel responsible for the dies. Though
recommendations call for at least one inspection a month, the inspection frequency should be based on the
amount of use, ambient working conditions, operator training and skill, and established company standards.
These inspections should be performed in the following sequence:
Visual Inspection
1. Remove all lubrication and accumulated film by immersing the dies in a suitable commercial
degreaser that will not affect paint or plastic material.
2. Make sure all die holding screws, retaining rings, and die components are in place. Refer to the parts
listed in Figure 5 if replacements are necessary.
3. Check all bearing surfaces for wear. Remove and replace worn components.
4. Inspect the crimp area for flattened, chipped, cracked, worn, or broken areas. If damage is evident,
the dies must be repaired before returning them to service. See Section 5, REPLACEMENT AND
Gaging the Crimping Chamber
This inspection requires the use of a plug gage conforming to the dimensions provided in Figure 4. TE
does not manufacture or market these gages.Refer to Instruction Sheet 408-7424 for more information on
plug gages. Proceed as follows:
1. Mate the dies until it is evident that they have bottomed. Hold the dies in this position with a pressure
of approximately 69 kPa [10 psi].
2. Align the GO element with the appropriate crimping area. Push element straight into the crimping area
without using force. The GO element must pass completely through the crimping area as shown in
Figure 4.
3. Now align the NO-GO element and try to insert it straight into the same crimping chamber. The NO-
GO element may start entry but must not pass completely through as shown in Figure 4.
4. Repeat Steps 2 and 3 for each crimp section listed in Figure 4.
If the crimping chamber conforms to the gage inspection, the dies are considered dimensionally correct
and should be lubricated with a THIN coat of any good SAE 20 motor oil. If not, the dies must be repaired
before returning them to service. See Section 5, REPLACEMENT AND REPAIR.
3 of 5
Rev B
408-9167
Suggested Plug Gage Design
Inspection of Crimping Chamber
GO
NO-GO
Diameter
Diameter
Crimping Chamber
W
W
NO-GO Element
GO Element
GO element must pass
completely through the
crimping chamber
NO-GO element may enter
partially, but must not pass
completely through the
crimping chamber
Center Contact
Die Closure Configurati
Ferrule Die Closure
Configuration
GAGE ELEMENT DIAMETER
NO-GO
CONNECTOR
CRIMPING CHAMBER
GO
“W” WIDTH (MAX)
221980-2
221981-2
228596-4
228618-4
Center Contact
Ferrule
0.940-0.947 [.0370-.0373]
1.013-1.016 [.0399-.0400]
5.484-5.486 [.2159-.2160]
---
5.359-5.367 [.2110-.2113]
2.54 [.100]
Figure 4
5. REPLACEMENT AND REPAIR
Replacement parts are listed in Figure 5. A complete inventory can be stocked and controlled to prevent lost
time when replacement of parts is necessary. Order replacement parts through your TE Representative, or call
1-800-526-5142, or send a facsimile of your purchase order to 1-717-986-7605, or write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
For repair service, please contact a TE Representative at 1-800-526-5136.
6. REVISION SUMMARY
Updated document to corporate requirements
Changed artwork in Figure 4
Changed information in table in Figure 4.
4 of 5
Rev B
408-9167
5
6
1
4
3
33.32
[1.312]
2
15.88
[.625]
24.13
[.950]
REPLACEMENT PARTS
DESCRIPTION
ITEM
PART NUMBER
313053-1
QTY PER DIE ASSY
1
2
3
4
5
6
CRIMPER, Stationary
CRIMPER, Movable
LOCATOR
1
1
1
2
1
2
313054-1
313055-1
1-21046-3
2-59674-7
306105-7
RING, Retaining
SPACER, Upper
SCREW
Figure 5
5 of 5
Rev B
相关型号:
©2020 ICPDF网 联系我们和版权申明