020-2944-XX [TEKTRONIX]
P7600 Series TriMode⢠Probes;
| 型号： | 020-2944-XX |
| 厂家： | 
TEKTRONIX, INC. |
| 描述： | P7600 Series TriMode⢠Probes |
| 文件： | 总10页 (文件大小：516K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
™
P7600 Series TriMode Probes
®
TekConnect Interface - TekConnect scope/probe control and usability
Direct control from probe compensation box or from scope menu
Applications
Including, but not limited to:
MIPI M-PHY, PCI Express, Serial ATA, Serial Attached SCSI, Fibre
Channel, and HDMI
Combining TriMode probing with low noise
performance
TriMode probing enhances productivity by enabling differential, single-
ended, and common mode measurements with a single probe setup.
Connecting a probe to the device under test can be a time consuming
activity, especially if the probe has to be set up differently to make all the
necessary measurements. TriMode probing improves productivity by
reducing setup time, because only one setup is needed to make the three
different types of measurements. Switching between Differential Mode [A-
B], Single-Ended Mode [A-Gnd, B-Gnd], and Common Mode [((A+B)/2)-
Gnd] is as easy as a press of a button.
P7633 Low Noise TriMode Probe
The P7600 Series TriMode probes and the MSO/DPO70000DX and DPO/
DSA70000D Series Oscilloscopes are designed to deliver the industry's
lowest system noise levels. This high sensitivity is critical for being able to
make accurate measurements on low amplitude signals.
Key performance specs
Full 33 GHz bandwidth to the probe tip (P7633)
Industry's lowest probe and oscilloscope system noise
Key features
™
TriMode probe - one setup, three measurements without adjusting
probe tip connections
Differential
Single ended
Changing input modes on the probe is as easy as a press of a button
Common mode
As high speed serial data standards increase in speed and signal swings
shrink, probes with high bandwidth coupled with low noise and high
sensitivity are increasingly important for making accurate measurements.
Remote head design connectivity
Allows placement of probe amplifier close to the circuit being
measured
Coaxial adapters
2.92mm
SMP
P7500 probe tip adapter
Use P7500 Series TriMode solder-in probe tips
Probe automatically detects tips and applies DSP correction filters
Probe-specific S-parameters
12 Gb/s 200 mVpp signal measured with a P7633 and a P76CA-292C coaxial adapter
Unique DSP filters created from data stored in the probe
www.tek.com
1
Datasheet
P76CA-292C
The MSO/DPO70000DX and DPO70000SX Series oscilloscopes and the
P7600 Series TriMode probes were designed to deliver the industry's
lowest system noise levels. When used with a P76CA-xxx Coaxial
Adapters, the vertical setting on the oscilloscope can be set as low as
3.48 mV/div with a system noise <1.1 mVrms at 33 GHz bandwidth.
This high sensitivity is critical for being able to make accurate
measurements on low amplitude signals. The P7600 Series TriMode
probes were designed to deliver superior sensitivity and allow the
oscilloscope to directly measure small signals without using a zoom
function. Using a zoom function to look at small signals does not change
the intrinsic noise floor of the instrument which can make measurements on
small signals problematic.
Connectivity
The P7600 Series probes utilize an interchangeable active tip design built
around a custom tip interface using high frequency SMPM connectors. The
P7600 Series probes feature an Automatic Adapter ID function that
recognizes the attached adapter and automatically applies the correct DSP
filters that eliminate imperfections in the frequency response all the way to
the probe tip. This feature eliminates the risk of manually selecting the
wrong tip type and is more efficient for the user.
Coaxial adapters
33 GHz Bandwidth Coaxial Adapter with 2.92 mm (Male) connectors and 6"
of high performance cable. This adapter is calibrated at the input
connectors and is ideal for directly connecting to devices with 2.92 mm or
SMA output connectors.
Coaxial adapters enable the probe to act like a differential input channel for
the oscilloscope which effectively doubles the number of differential signals
a single oscilloscope can measure simultaneously.
P76CA-SMP
P76CA-292
33 GHz Bandwidth Coaxial Adapter with 2.92 mm (Female) connectors.
This adapter is calibrated at the input connectors and is ideal for use with
off the shelf or custom cables. Low skew cable pairs should be used to
preserve full bandwidth performance.
2 www.tek.com
P7600 Series TriMode Probes
33 GHz Bandwidth Coaxial Adapter with SMP (Female) connectors and 6"
of high performance cable. This adapter is calibrated at the input
connectors and is ideal for directly connecting to devices with SMP output
connectors.
30 GHz Bandwidth P7500 Tip Adapter. The probe and oscilloscope system
will support up to 30 GHz of bandwidth when this adapter is used with the
P75PST Performance Solder Tip.
Unique probe filters
P7500 Series solder tip adapter
The P7600 Series probes contain probe specific S-parameter data.
Attaching a P7600 probe to a MSO/DPO70000DX or DPO70000SX
oscilloscope transfers this data to the instrument to create unique system
DSP filters based on the specific S-parameter data of the oscilloscope and
the probe. Creating unique filters based on the specific response of the
system is critical as bandwidths increase. At bandwidths of 33 GHz, small
variations in the signal path can lead to significant variation in frequency
response. These variations are corrected using DSP filtering.
This adapter allows the P7630 probe to use existing Tektronix P7500 probe
tips. The P7600 Series probe amplifiers have a 50 Ω input. When
combined with a P7500 probe tip, the probe turns into a passive Z0 style
probe with 450 Ω of differential input impedance. While Z0 probes can
typically present a significant DC load to the device under test, the P7600
Series probes will minimize the effect of DC loading through the use of
termination voltage adjustment.
P76TA
www.tek.com
3
Datasheet
Specifications
Model Overview
Probe model
Adapter
P7633
P7625
P76CA-xxx
P76TA
P76CA-xxx
P76TA
Characteristic
Bandwidth
33 GHz
14 ps
30 GHz
16 ps
25 GHz
18 ps
25 GHz
18 ps
Rise time (10-90%)
Rise time (20-80%)
11 ps
12 ps
14 ps
14 ps
Typical Characteristics
Attenuation
P76CA-xxx
P76TA
0.25X / 0.5X / 1X / 2X / 4X
1.25X / 2.5X / 5X / 10X / 20X
Input voltage range
P76CA-xxx
1.2 Vpp single-ended, 2.0 Vpp differential
6.0 Vpp single-ended, 10.0 Vpp differential
P76TA
Operating voltage window
P76CA-xxx
-4 V to +4 V
-5 V to +5 V
P76TA
Offset voltage range
-4 V to +4 V
-4 V to +4 V
Termination voltage range
DC input resistance
P76CA-xxx
50 Ω ±2 Ω
225 Ω
P76TA
Input return loss
P76CA-xxx
>20 dB to 5 GHz
>12 dB 5 GHz to 20 GHz
>10 dB 20 GHz to 30 GHz
>8 dB 30 GHz to 33 GHz
NA
P76TA
Z min
P76CA-xxx
P76TA
NA
225 Ω at 1 GHz, 150 Ω at 10 GHz, 100 Ω at 25 GHz
Noise, referred to input (System
noise with oscilloscope set in
minimum V/div setting)
<1.1 mVrms (33 GHz) <0.9 mVrms (25 GHz)
4 www.tek.com
P7600 Series TriMode Probes
Typical Characteristics
CMRR (differential mode)
P76CA-xxx
>40 dB at DC
>14 dB DC to 15 GHz
>6 dB 15 GHz to 30 GHz
>4 dB 30 GHz to 33 GHz
NA
P76TA
Nondestructive input voltage
range
P76CA-xxx
P76TA
-5 V to +5 V (DC + peak AC)
-8 V to +8 V (DC + peak AC)
Interface
TekConnect
Minimum system requirements
Instrument
Bandwidth
Firmware version
Recommended probe
MSO/DPO73304DX,
DPO73304SX, and DPO/
DSA73304D
33 GHz
V6.8 and above
P7633
MSO/DPO72504DX,
DPO73304SX, and DPO/
DSA72504D
25 GHz
V6.8 and above
P7625
Environmental characteristics
Temperature
Operating
0 to +40 °C (+32 °F to +104 °F)
-20 °C to +71 °C (-4 °F to +160 °F)
Nonoperating
Humidity
Operating
Up to +40 °C (+104 °F) 20%-80% RH
Nonoperating
+30 °C to +46 °C (+86 °F to +115 °F) 0-90% RH
Altitude
Operating
3000 meters (9842 feet)
Nonoperating
12000 meters (39,370 feet)
www.tek.com
5
Datasheet
Ordering information
Models
™
P7633
P7625
Low Noise TriMode Probe, 33 GHz, TekConnect Interface
™
Low Noise TriMode Probe, 25 GHz, TekConnect Interface
NOTE: All P7600 Series probes require a P76CA-SMP, P76CA-292, P76CA-292C, or P76TA adapter for connection to the device under test. These adapters are ordered
separately.
Options
Service options
Opt. C3
Opt. C5
Opt. D3
Opt. D5
Opt. G3
Opt. G5
Opt. R3
Opt. R3DW
Opt. R5
Opt. R5DW
Calibration Service 3 Years
Calibration Service 5 Years
Calibration Data Report 3 Years (with Opt. C3)
Calibration Data Report 5 Years (with Opt. C5)
Complete Care 3 Years (includes loaner, scheduled calibration, and more)
Complete Care 5 Years (includes loaner, scheduled calibration, and more)
Repair Service 3 Years (including warranty)
Repair Service Coverage 3 Years (includes product warranty period). 3-year period starts at time of instrument purchase
Repair Service 5 Years (including warranty)
Repair Service Coverage 5 Years (includes product warranty period). 5-year period starts at time of instrument purchase
Accessories
Standard accessories
Accessory
Quantity
Tektronix part number
071-3026-xx
Printed Manual
1 kit
Data Calibration Report: Lists the manufacturing test results of your probe at the 1 each
time of shipment
Standard with probe
Certificate of Traceable Calibration
Antistatic wrist strap
1 each
1 each
1 each
1 each
3 each
1 each
1 kit
Standard with probe
006-3415-xx
067-3259-xx
012-0208-xx
276-1152-xx
129-2781-xx
016-0633-xx
DC probe calibration fixture
50 Ω BNC-M to BNC-M cable assembly, 10 in.
ESD protective cap
Hex wrench, 2 mm
Color band kit
6 www.tek.com
P7600 Series TriMode Probes
DC Probe Calibration Fixture
Recommended accessories
Description
Tektronix part number
P76CA-292
P76CA-292C
P76CA-SMP
P76TA
2.92 mm Coaxial Adapter
2.92 mm Coaxial Adapter with Cables
SMP Coaxial Adapter with Cables
P7500 Tip Adapter
P7500 TriMode Performance Solder Tip
P7500 TriMode Long Reach Solder Tip
P7500 TriMode Resistor Solder Tip
P7500 TriMode Extended Resistor Solder Tip
Solder Tip Ramps, Kit of 25
P75PST
P75TLRST
020-2936-xx
020-2944-xx
020-3118-xx
006-8237-xx
067-2431-xx
003-1934-xx
020-3105-xx
003-1896-xx
013-0359-xx
017-0103-xx
020-2937-xx
Adhesive Tip Tape, Strip of 10
Deskew Fixture
SMPM Bullet Removal Tool
SMPM Replacement Bullet Contacts (package of 4)
G3PO Bullet Removal Tool
G3PO Replacement Bullet Contacts (package of 4)
Wire Kit
Replacement Resistor Kit
www.tek.com
7
Datasheet
P7600 Series Probes Deskew Fixture
P75PST Solder Tip
Bullets and Bullet Removal Tool
Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar.
Product(s) complies with IEEE Standard 488.1-1987, RS-232-C, and with Tektronix Standard Codes and Formats.
8 www.tek.com
P7600 Series TriMode Probes
www.tek.com
9
Datasheet
ASEAN / Australasia (65) 6356 3900
Belgium 00800 2255 4835*
Austria 00800 2255 4835*
Brazil +55 (11) 3759 7627
Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777
Canada 1 800 833 9200
Central East Europe and the Baltics +41 52 675 3777
Finland +41 52 675 3777
Central Europe & Greece +41 52 675 3777
France 00800 2255 4835*
Denmark +45 80 88 1401
Germany 00800 2255 4835*
Hong Kong 400 820 5835
India 000 800 650 1835
Italy 00800 2255 4835*
Japan 81 (3) 6714 3086
Luxembourg +41 52 675 3777
The Netherlands 00800 2255 4835*
Poland +41 52 675 3777
Russia & CIS +7 (495) 6647564
Sweden 00800 2255 4835*
Mexico, Central/South America & Caribbean 52 (55) 56 04 50 90
Norway 800 16098
Portugal 80 08 12370
South Africa +41 52 675 3777
Switzerland 00800 2255 4835*
USA 1 800 833 9200
Middle East, Asia, and North Africa +41 52 675 3777
People's Republic of China 400 820 5835
Republic of Korea +822 6917 5084, 822 6917 5080
Spain 00800 2255 4835*
Taiwan 886 (2) 2656 6688
United Kingdom & Ireland 00800 2255 4835*
* European toll-free number. If not accessible, call: +41 52 675 3777
For Further Information. Tektronix maintains a comprehensive, constantly expanding collection of application notes, technical briefs and other resources to help engineers working on the cutting edge of technology. Please visit www.tek.com.
©
Copyright Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specification and
price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks of their respective companies.
23 May 2017 51W-28184-4
www.tek.com
相关型号：
020-3%-FA3-90PPM-CARDPACK
Fixed Resistor, Wire Wound, 3W, 0.02ohm, 130V, 3% +/-Tol, -90,90ppm/Cel,
VISHAY
©2020 ICPDF网 联系我们和版权申明