EM-1RI [SYSTEMSENSOR]

Relay Module; 继电器模块


型号：	EM-1RI
厂家：	SYSTEMSENSOR ADVANCED IDEAS.
描述：	Relay Module 继电器模块继电器
文件：	总2页 (文件大小：228K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue, St. Charles, Illinois 60174

1.800.SENSOR2; Fax: 630.377.6495

www.systemsensor.com

EM-1RI Relay Module

SPECIFICATIONS

Normal Operating Voltage:

Standby Current:

Alarm Current:

15 to 30 VDC

580 µA max. average (continuous broadcasts)

2.0 mA (red LED on)

Short Circuit Current, Dry Control Input:

Maximum Resistance, Dry Contact Input:

Temperature Range:

Humidity:

30 µA max. average (5VDC)

100 Ω

32°F to 120°F (0°C to 49°C)

10% to 93% RH Non-condensing

4.17˝ H × 4.26˝ W × 1.22˝ D; (106 mm H × 108 mm W × 31 mm D)

Dimensions:

Accessories:

Wall cover plate (included); SMB500 Surface Mount Electrical Box; CB500 Control Module Barrier

CURRENT RATING

MAXIMUM VOLTAGE

30 VDC

LOAD DESCRIPTION

Resistive

APPLICATION

Non-Coded

Coded

3 A

2 A

30 VDC

Resistive

.9 A

.5 A

1 A

.3 A

1.5 A

.7 A

2 A

110 VDC

125 VDC

30 VDC

125 VAC

25 VAC

Resistive

Non-Coded

Coded

Inductive (L/R=5ms)

Inductive (L/R=2ms)

Inductive (PF=.35)

Inductive (PF = .35)

Inductive (PF=.35)

Coded

Non-Coded

70.7 VAC

25 VAC

NOTE: This module is not approved for use in the European Union, at or above 50VAC or 70VDC.

BEFORE INSTALLING

WIRING

This information is included as a quick reference installation guide. Refer to the

appropriate control panel installation manual for detailed system information.

If the modules will be installed in an existing operational system, inform the

operator and local authority that the system will be temporarily out of service.

NOTE: All wiring must conform to applicable local codes, ordinances,

and regulations.

1. Install module wiring in accordance with the job drawings and appropri-

ate wiring diagrams.

NOTICE: This manual should be left with the owner/user of this equipment.

NOTE: Separate cable entry openings must be used to maintain required

spacing between power limited and non-power limited wiring. Optional

EA-CB may be required to separate power limited and non power limited

wiring in the electrical box.

GENERAL DESCRIPTION

Relay Module, Model EM-1RI, is to be designed for use in activation of the

types of products that are generally connected to an intelligent fire alarm sys-

tem. It provides two sets of form C contacts that switch together (one DPDT

relay). There is also an input that is capable of monitoring a dry set of contacts

for open or closed conditions. The module also has on-board short circuit iso-

lators to prevent shorts on the signaling line circuit from disabling more than

one device on the intelligent loop.

2. Set the address on the module per job drawings using the IR configura-

tion tool (model no. EA-CT).

3. Secure module to electrical box (supplied by installer).

AUTO ADDRESSING

Eclipse Series devices are capable of supporting auto addressing, if the fire

alarm control panel is designed to do so. In auto addressing, the control panel,

through the use of each device’s on-board isolators, can automatically assign

device addresses.

COMPATIBILITY REQUIREMENTS

To ensure proper operation, this module shall be connected to a listed compat-

ible control panel.

MOUNTING

In order to control which devices are addressed first in wiring configurations

with branches, a branch marker can be set at a particular device. A branch

marker is an electronic value from 0 to 255 stored in the device memory. The

branch markers are set with the IR configuration tool, EA-CT.

The module mounts directly to 4-inch square electrical boxes. The box must

have a minimum depth of 2¹⁄

inches. Modules must be mounted with the ar-

row facing upward for proper operation of the IR programming tool. Surface

mounted electrical boxes (SMB500) are available from System Sensor.

TERMINAL DEFINITIONS

LED INDICATOR

T1 (+) SLC in/out

T7 Normally Closed #1

T8 Common #1

T2 (–) SLC in/out

T3 (+) SLC in/out

T9 Normally Open #1

T10 Normally Closed #2

T11 Common #2

T4 (–) SLC in/out

T5 (+) Dry Contact Input

T6 (–) Dry Contact Input

T12 Normally Open #2

WARNING

All relay switch contacts are shipped in the standby state (open) state, but may

have transferred to the activated (closed) state during shipping. To ensure that

the switch contacts are in their correct state, modules must be made to com-

municate with the panel before connecting circuits controlled by the module.

IR RECEIVER

C0166-00

D500-61-00

I56-2023-005

FIGURE 2: WIRING DIAGRAM:

SIGNAL LINE CIRCUIT (SLC)

30 VDC MAX.

TWISTED PAIR RECOMMENDED AND IS POWER

LIMITED AND SUPERVISED

CONNECT MODULES

TO LISTED COMPATIBLE

CONTROL PANELS ONLY

( + )

( – )

( + )

( – )

( + )

FROM PANEL OR

( – )

PREVIOUS PANEL

( + )

RELAY

CONTACTS

TO NEXT DEVICE

( – )

{

MODULE DOES NOT SUPER-

VISE CONTROLLED CIRCUITS.

TERMINALS 1-6 ARE POWER

LIMITED. TERMINALS 7-12 ARE

NON-POWER LIMITED.

NORMALLY OPEN (T12)

COMMON (T11)

RELAY

CONTACT #2

NORMALLY CLOSED (T10)

NOTE: NORMALLY OPEN OR

NORMALLY CLOSED CONTACT

DEVICE (NOT SUPERVISED).

NOTE: NORMALLY CLOSED

OPTION MAY NOT BE USED

FOR FIRE APPLICATIONS.

NORMALLY OPEN (T9)

COMMON (T8)

RELAY

CONTACT #1

NORMALLY CLOSED (T7)

C0110-02

ThREE-YEAR LIMITED WARRANTY

#__________, 3825 Ohio Avenue, St. Charles, IL 60174. Please include a note describing

the malfunction and suspected cause of failure. The Company shall not be obligated to

repair or replace units which are found to be defective because of damage, unreasonable

use, modifications, or alterations occurring after the date of manufacture. In no case shall

the Company be liable for any consequential or incidental damages for breach of this

or any other Warranty, expressed or implied whatsoever, even if the loss or damage is

caused by the Company’s negligence or fault. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation or exclusion

may not apply to you. This Warranty gives you specific legal rights, and you may also

have other rights which vary from state to state.

System Sensor warrants its enclosed module to be free from defects in materials and

workmanship under normal use and service for a period of three years from date of

manufacture. System Sensor makes no other express warranty for this module. No agent,

representative, dealer, or employee of the Company has the authority to increase or

alter the obligations or limitations of this Warranty. The Company’s obligation of this

Warranty shall be limited to the repair or replacement of any part of the module which

is found to be defective in materials or workmanship under normal use and service

during the three year period commencing with the date of manufacture. After phoning

System Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return Authorization

number, send defective units postage prepaid to: System Sensor, Returns Department, RA

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installa-

tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

D500-61-00

I56-2023-005

EM-1RI [SYSTEMSENSOR]

相关型号：

EM-1SRI

EM-23046-C36

EM-23046-P16

EM-23069-000

EM-24047-000

EM-4530

EM-4530-C

EM-5

EM-6027

EM-6027P

EM-6027P_18

EM-6781