NQ60T60QGC20NYC-G [SYNQOR]
Quarter-brick DC-DC Converter; 四分之一砖DC- DC转换器型号: | NQ60T60QGC20NYC-G |
厂家: | SYNQOR WORLDWIDE HEADQUARTERS |
描述: | Quarter-brick DC-DC Converter |
文件: | 总9页 (文件大小:615K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Technical
Specification
NQ60x60QGC20
9-60 V
Continuous Input
0-60 V
Outputs
20 A
Current
Non-
Isolated
Quarter-brick
DC-DC Converter
®
TheꢀNiQor ꢀquarter-brickꢀdc-dcꢀconverterꢀisꢀaꢀnon-isolatedꢀ
buck-boost
regulator,
which
employs
synchronousrectificationꢀ
toꢀachieveꢀextremelyꢀhighꢀconversionꢀefficiency.ꢀTheꢀHighꢀ
InputꢀVoltageꢀNiQorꢀBrickꢀfamilyꢀofꢀconvertersꢀcanꢀbeꢀusedꢀ
inꢀtraditionalꢀDPAꢀ(distributedꢀpowerꢀarchitecture)ꢀsystemsꢀ
orꢀprovideꢀaꢀregulatedꢀoutputꢀvoltageꢀfromꢀaꢀbatteryꢀsourceꢀ
orꢀ otherꢀ variableꢀ voltageꢀ source.ꢀ Theꢀ NiQorꢀ Brickꢀ familyꢀ
canꢀ beꢀ configuredꢀ toꢀ Buckꢀ theꢀ inputꢀ voltageꢀ downꢀ toꢀ aꢀ
lowerꢀ voltageꢀ orꢀ Boostꢀ theꢀ inputꢀ voltageꢀ upꢀ toꢀ aꢀ higherꢀ
voltageꢀusingꢀaꢀsingleꢀexternalꢀresistor.ꢀTheseꢀmodulesꢀareꢀ
RoHSꢀ6/6ꢀcompliantꢀ(seeꢀlastꢀpage).ꢀ
Non-Isolated
ꢀOperational Features
•ꢀUltraꢀhighꢀefficiency,ꢀupꢀtoꢀ95%ꢀatꢀfullꢀratedꢀload
•ꢀDeliversꢀupꢀtoꢀ20ꢀAꢀofꢀoutputꢀcurrent
•ꢀInputꢀVoltageꢀRange:ꢀ9ꢀ-ꢀ60ꢀV
NiQor quarter-brick module
•ꢀOutputꢀvoltageꢀrange:ꢀ0ꢀ-ꢀ60ꢀVꢀ(negativeꢀoutputꢀisꢀpossible)
•ꢀExtensiveꢀon-boardꢀinputꢀandꢀoutputꢀfiltering
•ꢀNoꢀminimumꢀloadꢀrequirementꢀmeansꢀnoꢀpreloadꢀ
resistorsꢀrequired
•ꢀBuckꢀorꢀbuck-boostꢀmodeꢀavailable
•ꢀAdjustableꢀcurrentꢀlimitꢀwithꢀcurrentꢀmonitorꢀ(Cꢀoption)
ꢀProtection Features
•ꢀInputꢀunder-voltageꢀlockoutꢀprotectsꢀtheꢀconverterꢀatꢀlowꢀ
inputꢀvoltageꢀconditions
•ꢀOver-currentꢀshutdownꢀprotectsꢀconverterꢀfromꢀexcessiveꢀ
ꢀMechanical Features
loadꢀcurrentꢀorꢀshortꢀcircuits
•ꢀOutputꢀover-voltageꢀprotectionꢀprotectsꢀloadꢀfromꢀ
damagingꢀvoltages
•ꢀIndustryꢀstandardꢀquarter-brickꢀpin-outꢀconfiguration
•ꢀSize:ꢀ1.54"ꢀxꢀ2.39"ꢀ(39x60.6ꢀmm)
•ꢀTotalꢀheightꢀonlyꢀ0.515"ꢀ(13.08ꢀmm)
•ꢀTotalꢀweight:ꢀ3ꢀozꢀ(85ꢀg)
•ꢀThermalꢀshutdownꢀprotectsꢀconverterꢀfromꢀabnormalꢀ
environmentalꢀconditions
ꢀSafety Features
ꢀControl Features
•ꢀUL/cULꢀ60950-1ꢀrecognizedꢀ(USꢀ&ꢀCanada)
•ꢀTUVꢀcertifiedꢀtoꢀEN60950-1
•ꢀOn/Offꢀcontrol
•ꢀBoardꢀandꢀplasticꢀcomponentsꢀmeetꢀUL94V-0ꢀ
•ꢀOutputꢀvoltageꢀtrimꢀpermitsꢀcustomꢀvoltagesꢀ
•ꢀRemoteꢀSenseꢀ(Sꢀoption,ꢀstandard)
•ꢀCurrentꢀlimitꢀtrimꢀ(Cꢀoption)
flammabilityꢀrequirements
Product # NQ60x60QGC20
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-NQ6060W Rev. B
03/16/09
Page 1
9 - 60 V
0 - 60 V
20 A
Input:
Outputs:
Current:
Package:
Quarter-brick
Technical Specification
MECHANICALꢀDIAGRAM
1.536 ±.020
[ 39,01±0,5]
.810[ 20,57 ]
.600[ 15,24 ]
.450[ 11,43 ]
.300[ 7,62 ]
.150[ 3,81 ]
.263±.020
[ 6,7±0,5 ]
.515±.025
[13.08± 0.63]
OVERALL HEIGHT
8
7 6 5 4
2.386±.020
[ 60,6±0,5]
Top View
Side View
1.86
[ 47,2 ]
2.00
[ 50,8]
M3 THREADED INSERTS
2 PLACES
SEE NOTES 1 & 2
.145
[ 3,68 ]
1
2
3
.020±.010
.468±.020[ 11,89±0,5 ]
.300[ 7,62 ]
[ 0,51±0,25]
BOTTOMSIDE
CLEARANCE
.183±.020
[ 4,65±0,5]
.600[ 15,24 ]
PIN DESIGNATIONS
NOTES
Pin Label Function
1)
M3 SCREWS USED TO BOLT UNIT'S BASEPLATE TO OTHER SURFACES
SUCH AS HEATSINKS MUST NOT EXCEED 0.090" (2.28mm) DEPTH
BELOW THE SURFACE OF THE BASEPLATE.
1
Vin(+)
Positive input
TTL input to turn converter on and off,
referenced to Vin(-), with internal pull up
2
ON/OFF
2)
3)
APPLIED TORQUE PER SCREW SHOULD NOT EXCEED 6in-lb (0.7Nm)
Negative input voltage, internal short to
Pin 4
Negative output voltage, internal short to
Pin 3
Negative remote sense. See note 1
(S option)
Isense (C option)
Output voltage trim
Positive remote sense. See note
(S option)
Isense (C option)
Positive output voltage
Vin
(-)
BASEPLATE FLATNESS TOLERANCE IS 0.004" (.10mm) TIR FOR
SURFACE
3
4
4)
5)
6)
7)
8)
PINS 1-3, 5-7 ARE 0.040" (1.02mm) DIA. WITH 0.080" (2.03mm) DIA.
STANDOFF SHOULDERS
Vout
(-)
PINS 4 AND 8 ARE 0.062" (1.57mm) DIA. WITH 0.100" (2.54mm)
DIA. STANDOFF SHOULDERS
SENSE
(-)
5
6
7
8
ALL PINS: MATERIAL: COPPER ALLOY
FINISH: MATTE TIN OVER NICKEL PLATE
TRIM
UNDIMENSIONED COMPONENTS ARE SHOWN FOR VISUAL
REFERENCE ONLY
SENSE
(+)
ALL DIMENSIONS IN INCHES(mm)
TOLERANCES: X.XXIN +/-0.02 (X.Xmm +/-0.5mm) X.XXXIN +/-
0.010 (X.XXmm +/-0.25mm)
Vout(+)
Notes:
9)
Weight: =3oz (85g) typical
1)SENSE(–) should be connected to Vout(–) either remotely or at
the converter
10)
Workmanship: Meets or exceeds IPC-A-610C Class II
2)SENSE(+) should be connected to Vout(+) either remotely or at
the converter.
Product # NQ60x60QGC20
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-NQ6060W Rev. B
03/16/09
Page 2
9 - 60 V
0 - 60 V
20 A
Input:
Outputs:
Current:
Package:
Quarter-brick
Technical Specification
NQ60x60QGC20 ELECTRICAL CHARACTERISTICS
Ta = 25 °C, airflow rate = 300 LFM, Vin = 24 V dc unless otherwise noted; full operating temperature range is -40 °C to +105 °C ambient temperature with appropriate power derating. Specifications
subject to change without notice.
Parameter
Vout Min. Typ. Max. Units Notes & Conditions
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Non-Operating
Operating
Storage Temperature
All
All
All
All
0
80
60
125
5.5
V
V
°C
V
Continuous
Continuous
-55
0
Voltage at ON/OFF input pin
RECOMMENDED OPERATING CONDITIONS
Input Voltage Range
All
All
9
60
25
20
V
A
A
µF
V
A
Turn on at 10V
Input Fuse Rating
Fast blow external fuse recommended
Input current max equals output rated current
ESR < 1.5 Ω
Input Current
External Input Capacitance
Output Voltage
All
All
All
100
0
0
60
20
Output Current
Output voltage dependent
INPUT CHARACTERISTICS
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Lockout Hysteresis
Input Current Limit
No-Load Input Current
“
All
All
All
All
12
24
48
All
All
9.2
8.1
9.5
8.5
1.0
24
93
85
235
35
10
8.9
V
V
V
A
mA
mA
mA
mA
µF\µH\µF
“
Disabled Input Current
Input Filter Components Value (C\L\C)
OUTPUT CHARACTERISTICS
Output Voltage Range
Operating Output Current Range
Output Voltage Regulation
Total Output Voltage Range
Output Voltage Ripple and Noise (pk-pk/36Vin)
“
8.8\2.2\26.4
All
All
0
0
60
20
V
A
Set output by Rtrim resistor
All
12
24
48
All
All
±480 mV ±4%*Vout
Sense pin, over sample, line, load, temp. & life
36 Vin Full Load; 100uF; 20 MHz b.w.
15
15
40
24
mV
mV
mV
A
"
“
Output DC Over Current limit
External Output Capacitance
C Option: Isense voltage
No load
Effective on input, output condition
ESR > 1 mΩ
0
1000
µF
All
All
All
1.25
1.83
10
V
V
kΩ
Full load
20 A load
Output resistance of Isense
C Option: Itrim voltage
Voltage at no load
All
All
All
All
All
0.12
2.12
10.2
2.5
V
V
kΩ
V
Voltage at maximum load
Pull-Up Resistance of Itrim Pin
Pull-Up Voltage
20 A load
C Option: Reverse Current
TEMP LIMITS FOR POWER DERATING
Semiconductor Junction Temperature
Board Temperature
Baseplate Temperature
EFFICIENCY
2
µA
Enabled or Disabled
All
All
All
125
125
100
°C
°C
°C
Package rated to 150 °C
ULrated max operating temp 130 °C
100% Load; 24 Vin
“ ; 48 Vin
“ ; 24 Vin
50% Load; 24 Vin
12
24
48
12
24
48
92
95
94
94
95
95
%
%
%
%
%
%
W mode only
W mode only
“ ; 48 Vin
“ ; 24 Vin
Product # NQ60x60QGC20
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-NQ6060W Rev. B
03/16/09
Page 3
9 - 60 V
0 - 60 V
20 A
Input:
Outputs:
Current:
Package:
Quarter-brick
Technical Specification
NQ60x60QGC20 ELECTRICAL CHARACTERISTICS (Continued)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 24 V dc unless otherwise noted; full operating temperature range is -40 °C to +105 °C ambient temperature with appropriate power derating. Specifications
subject to change without notice.
Parameter
Vout Min. Typ. Max. Units Notes & Conditions
DYNAMIC CHARACTERISTICS
Output Voltage during Current Transient
For a Step Change in Output Current
Settling Time
All
1
V
(0.1 A/µs); 50%-75%-50% Iout max
To within 1.5% Vout nom.
All
5
ms
Turn on Transient
Startup delay
Rise Rate
Output Voltage Overshoot
FEATURE CHARACTERISTICS
Switching Frequency
All
All
All
2
0.6
ms
V/ms
V
Resistive load
"
"
0
All
240
250
260
kHz
ON/OFF Control
Negative Logic (N) ON/OFF Control
Off-State Voltage
On-State Voltage
Pull-Up Voltage
Pull-Up Resistance
Output Voltage Trim Range
Input/Output Over-Voltage Protection
Over-Temperature Shutdown
Over-Temperature Shutdown Restart Hysteresis
RELIABILITY CHARACTERISTICS
Calculated MTBF (TR-NWT-000332; Telcordia)
Calculated MTBF (MIL-HDBK-217F; MIL-217)
Field Demonstrated MTBF
All
All
All
All
All
All
All
All
1.8
0
3.3
0.8
V
V
V
kΩ
V
V
3.3
10
0
66
60
75
Measured Vout+ to common pins
Over full temp range
Average PCB Temperature
72
115
15
°C
°C
6
6
6
All
All
All
TBD
TBD
10 Hrs. 100% load, 200LFM, 40 °C Ta
10 Hrs. 100% load, 200LFM, 40 °C Ta
10 Hrs. See our website for details
STANDARDS COMPLIANCE
Parameter
STANDARDS COMPLIANCE
Notes & Conditions
UL/cUL 60950-1
Pending UL Approval File # E194341
EN60950-1
Certified by TUV
Needle Flame Test (IEC 695-2-2)
IEC 61000-4-2
GR-1089-CORE
Test on entire assembly; board & plastic components UL94V-0 compliant
ESD test, 8 kV - NP, 15 kV air - NP (Normal Performance)
Section 7 - electrical safety, Section 9 - bonding/grounding
Telcordia (Bellcore) GR-513
Note: An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new
releases or download from the SynQor website.
QUALIFICATION TESTING
Parameter
QUALIFICATION TESTING
Life Test
# Units Test Conditions
32
95% rated Vin and load, units at derating point, 1000 hours
Vibration
5
5
10
5
5
5
10-55 Hz sweep, 0.060" total excursion, 1 min./sweep, 120 sweeps for 3 axis
100g minimum, 2 drops in x and y axis, 1 drop in z axis
-40 °C to 100 °C, unit temp. ramp 15 °C/min., 500 cycles
Toperating = min to max, Vin = min to max, full load, 100 cycles
Tmin-10 °C to Tmax+10 °C, 5 °C steps, Vin = min to max, 0-105% load
85 °C, 85% RH, 1000 hours, continuous Vin applied except 5 min/day
MIL-STD-883, method 2003
Mechanical Shock
Temperature Cycling
Power/Thermal Cycling
Design Marginality
Humidity
Solderability
15 pins
Note: Extensive characterization testing of all SynQor products and manufacturing processes is performed to ensure that we supply
robust, reliable product. Contact the factory for official product family qualification documents.
Product # NQ60x60QGC20
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-NQ6060W Rev. B
03/16/09
Page 4
9 - 60 V
0 - 60 V
20 A
Input:
Outputs:
Current:
Package:
Quarter-brick
Technical Specification
100
95
90
85
80
75
70
65
60
30
25
20
15
10
5
48Vin 24Vout
24Vin 12Vout
48Vin 12Vout
24Vin48Vout
12Vin 24Vout
12Vin 48Vout
48Vin 24Vout
24Vin 12Vout
48Vin 12Vout
24Vin 48Vout
12Vin 24Vout
12Vin 48Vout
0
0
5
10
15
20
0
5
10
15
20
Load Current (A)
Load Current (A)
Figure 1: Efficiency at different output voltage vs. load current for dif-
Figure 2: Power dissipation at different output voltage vs. load current
ferent input voltage at 25 °C
.
for different input voltage at 25 °C.
21
18
15
12
9
See Fig. 5
1ꢀµH
source
impedance
See Fig. 6
iC
iS
Dc-dc
Converter
Vin
Vout
Tb=80 C; Vout=12 V
Tb=100 C; Vout=12 V
Tb=80 C; Vout=24 V
Tb=100 C; Vout=24 V
Tb=80 C; Vout=48 V
Tb=100 C; Vout=48 V
6
VSOURCE
100ꢀµFꢀ
C*
100mWꢀESRꢀ
3
tantalum
capacitor
0
*ꢀSeeꢀvaluesꢀforꢀrecommendedꢀexternalꢀinputꢀcapacitance.ꢀ
Inductorꢀoptionalꢀasꢀneeded.
0
10
20
30
40
50
60
Input Voltage (V)
Figure 3: Maximum output power derating curve with a controlled
baseplate temperature of 80ºC and 100ºC.
Figure 4: Test set-up diagram showing measurement points for Input
Terminal Ripple Current (Figure 5), and Output Voltage Ripple
(Figure 6).
60 Vout
60 Vout
48 Vout
48 Vout
24 Vout
12 Vout
24 Vout
12 Vout
Figure 5: Input Terminal Ripple Current at 36 V input and rated
Figure 6: Output Voltage Ripple at 36 V input and rated load current
load current (500 mA/div). Load capacitance: 100
Bandwidth: 20 MHz. See Figure 4.
µF electrolytic cap.
(50 mV/div). Load capacitance: 100
MHz. See Figure 4.
µF electrolytic cap.. Bandwidth: 20
Product # NQ60x60QGC20
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-NQ6060W Rev. B
03/16/09
Page 5
9 - 60 V
0 - 60 V
20 A
Input:
Outputs:
Current:
Package:
Quarter-brick
Technical Specification
60 Vout
48 Vout
60 Vout
48 Vout
24 Vout
12 Vout
24 Vout
12 Vout
on/off
on/off
Figure 7: Turn-on transient at 36 V input; full load (20 ms/div).
Ch 1: ON/OFF input (5 V/div)
Figure 8: Turn-on transient at 36 V input; zero load (20 ms/div).
Ch 1: ON/OFF input (5 V/div)
Ch 2-4: Vout (10 V/div)
Ch 2-4: Vout (10 V/div)
2.00
1.50
1.00
0.50
0.00
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
5
10
15
20
0
5
10
15
20
25
Load (A)
Current Limit (A)
Figure 9: Im o n pin voltage vs. load current at 24 V input and 13.8 V
output. Load capacitance: 100 F electrolytic cap. C option only.
Figure 10: Current limit vs. Itrim pin voltage at 24 V input and 13.8 V
µ
output. Load capacitance: 100
C option only.
µF electrolytic cap.
60 Vout
48 Vout
24 Vout
12 Vout
Figure 11: Output voltage response for 36 V input; 12 V, 24 V, 36 V output
to step-change in load current (50-75-50% of Iout max; di/dt=0.1A/
µ
s). Load
cap: 100 F, 100 m ESR tant, Ch 1-3: Vout (2 V/div);(5 ms/div).
µ
W
Product # NQ60x60QGC20
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-NQ6060W Rev. B
03/16/09
Page 6
9 - 60 V
0 - 60 V
20 A
Input:
Outputs:
Current:
Package:
Quarter-brick
Technical Specification
Alternatively, the TRIM pin can be driven from an external
voltage source:
BASIC OPERATION AND FEATURES
These converters use a digital controller for the buck stage and
boost stage (see Figure A). It automatically changes operating
mode (buck mode or boost) when the line voltage or output set
point changes. Both stages are accomplished with synchronous
rectifiers. Very high efficiency is maintained over wide input
and output ranges by shifting operational modes and use of
synchronous rectifiers.
Vout
V(pin6) = 2.366 –
2.316
2.314
Vmax
( )
where:
V
out = desired output voltage
Vin+
Vout+
Vmax = maximum rated output voltage
Loutput
Cout1
GATE_Q3
L
Linput
GATE_Q1
JUMPER
Q3
Q4
Q1
Q2
To maintain the accuracy of the output voltage over load current,
it is vital that any trim-up resistor be terminated directly to the
converter’s Sense(-) pin (S option) or Vout(-) pin (C option), not
at the connection to the load. A separate Kelvin connection to the
PCB pad for the Vout(-) is optimal.
Cout2
Cin1
Cin2
GATE_Q4
GATE_Q2
Vin-
Vout-
Figure A: Topology
PROTECTION FEATURES
W mode: Q3, Q4 are populated, Jumper is open.
T mode: Q3, Q4 are open, Jumper is populated.
Input Under-Voltage Lockout: The converter is designed
to turn off when the input voltage is too low, helping avoid an
input system instability problem, described in more detail in the
application note titled “Input System Instability”. The lockout
circuitry is a comparator with DC hysteresis. When the input
voltage is rising, it must exceed the typical Turn-On Voltage
Threshold value (listed on the specification page) before the
converter will turn on. Once the converter is on, the input
voltage must fall below the typical Turn-Off Voltage Threshold
value before the converter will turn off.
The converter runs at a fixed frequency with a predictable
EMI performance.
This series of quarter-brick and eighth-brick converters use the
industry standard footprint and pin-out configuration.
CONTROL FEATURES
REMOTE ON/OFF: The ON/OFF input permits the user to con-
trol when the converter is on or off. Only Negative ON/OFF logic
is available in this power module series.
Output Current Shutdown: To provide protection in an
output short condition, the unit is equipped with internal short
circuit protection. When the short protection is triggered, the
unit shutdowns first. After approximately 16 ms inhibit time, the
units turn on again. If the short condition remains, the current
limit circuit will limit the output current. The units operate
normally once the fault condition is removed.
Negative logic ON/OFF signal turns the module OFF during logic
high (leave the pin floating or set voltage between 1.8~3.3 V) and
turns the module ON during logic low [tie to Vin(-)].
Internal Over-Voltage Protection: To fully protect from
excessive output voltage, the output over-voltage shutdown
circuitry is contained. This OVP is independent of the trimmed set
point. The shutdown point is fixed on the standard option.
OUTPUT VOLTAGE TRIM: The output voltage can be
programmed to any voltage between 0 V dc and Vmax by
connecting one resistor between the Pin 6 (TRIM) pin and Pin 5
[Sense(-)]. For a desired output voltage, the value of the resistor
should be:
Over-Temperature Shutdown: A temperature sensor on
the converter senses the average temperature of the module.
The thermal shutdown circuit is designed to turn the converter
off when the temperature at the sensed location reaches the
Over-Temperature Shutdown value. It will allow the converter
to turn on again when the temperature of the sensed location
falls by the amount of the Over-Temperature Shutdown Restart
Hysteresis value.
11830 x V
11736
max
_
R
trim-up(Vout) =
(Ω)
10912
+
.0536
.058 x V
V
[( ) ]
out
max
Product # NQ60x60QGC20
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-NQ6060W Rev. B
03/16/09
Page 7
9 - 60 V
0 - 60 V
20 A
Input:
Outputs:
Current:
Package:
Quarter-brick
Technical Specification
APPLICATION CONSIDERATIONS
Vin-/
Vout+
Vin+
Cin1
Cin2
Limited output voltage resolution: The internal voltage
control feedback loop has limited resolution. Therefore, the
output voltage will exhibit discrete steps as the loop responds
to changes in line, load, trim, or remote sense. For instance,
on close examination, the startup ramp has a “stair-step”
shape. Likewise, a load transient response will be composed
of multiple discrete steps.
1
2
8
7
6
5
Vout+
SENSE+
TRIM
Vin+
Cout1
ENABLE
Dc/dc
converter
SENSE-
Rtrim-up
3
4
Vin-
Vout-
Vout-
Input filtering: These modules should be connected to a
low-impedance source. A highly inductive source can affect the
stability of the module. An input capacitance must be placed
directly adjacent to the input pin of the module, to minimize
input ripple voltage and ensure module stability.
Figure B: Negative output setup
Using this negative output setup impacts the available output
voltage range and current limit.
The output voltage range becomes 0 to Vmax - Vin, and the cur-
Output capacitance: For stable operation of the module, there
is no extra external capacitor required. To reduce the output
ripple and improve dynamic response to a step load change,
additional capacitance at the output can be used. Low ESR
polymer and ceramic capacitors are recommended to improve
the dynamic response of the module. In many applications,
however, additional external output capacitance is a requirement
which will cause the startup time to change.
rent limit is scaled by:
Vin
(Vin + Vout)
Current monitor/trimmable current limit (C option): In
addition to voltage trim, the C option offers an adjustable current
limit input and a current monitor output. The C option also
includes an ideal diode circuit in series with the Vout+ pin that
prevents reverse current flow. This enables applications such as
battery charging, current sharing, and current read back.
Remote sense (S option): Vout remote sensing is provided
to achieve proper regulation at the load points and reduce
effects of distribution losses on output line. In the event of an
open remote sense line, the module shall maintain local sense
regulation through an internal resistor. The module shall correct
for a total of 10% Vout.
Dc/dc
converter
Vout+
Vin+
Cin
1
2
8
7
6
5
Vout+
Vin+
IMON
VTRIM
IMON
Cout
ENABLE
Current limit: Available power is limited by output current
in buck mode (Vin>Vout), but by input current in boost mode
(Vin<Vout).
ITRIM
3
4
Vin-
Vout-
RadjIlim Rtrim-up
Vout-
Vin-
for Vin >Vout,
Figure C: Current monitor/trimmable current limit setup
Ilimit = 1.2 x Imax
The Rtrim-up resistor increases the output voltage, identical in
function to the S option.
for Vin < Vout,
Vin
The RadjItrim resistor reduces the output current limit, according
to the following equation:
Ilimit = 1.2 x Imax
Vout
( )
0.0469 Imax + Itrim
where Imax = Maximum rated output current
RadjItrim
=
10200 - 10
(Ω)
1.153 I
+ Itrim
[(
max
) ]
Negative output: This series of converters can be set to
negative output (see Figure B).
Alternatively, the Itrim pin can be driven from an external voltage
source:
V(pin5) = 2.085(Itrim/Imax) + 0.0953
where Itrim is the desired current limit setpoint
If Ilimit is less than Itrim, then Ilimit takes precedence.
The I
pin voltage tracks the output current, as shown in
mon
figure 10. This pin has a 10kOhm output impedance.
Product # NQ60x60QGC20
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-NQ6060W Rev. B
03/16/09
Page 8
9 - 60 V
0 - 60 V
20 A
Input:
Outputs:
Current:
Package:
Quarter-brick
Technical Specification
PART NUMBERING SYSTEM
ORDERING INFORMATION
The part numbering system for SynQor’s dc-dc converters
follows the format shown in the example below.
The tables below show the valid model numbers and ordering
options for converters in this product family. When ordering
SynQor converters, please ensure that you use the complete
15 character part number consisting of the 12 character base
part number and the additional 3 characters for options.
Add “-G” to the model number for 6/6 RoHS compliance.
NQ 60 W 60 Q
G
C 20 N N S - G
6/6ꢀRoHS
Optionsꢀ(seeꢀ
OrderingꢀInformation)
Input
Voltage
Output
Voltage
Max Output
Current
Model Number
OutputꢀCurrent
ThermalꢀDesign
PerformanceꢀLevel
PackageꢀSize
NQ60w60QGC20xyz-G
9 - 60 V
0 - 60 V
20 A
OutputꢀVoltage
Modeꢀ(seeꢀOrderingꢀInformation)
InputꢀVoltage
ProductꢀFamily
Theꢀfollowingꢀoptionsꢀmustꢀbeꢀincludedꢀinꢀplaceꢀofꢀthe x y z
spacesꢀinꢀtheꢀmodelꢀnumbersꢀlistedꢀabove.
Mode: w
Options Description: x y z
The first 12 characters comprise the base part number and
the last 3 characters indicate available options. The “-G”
suffix indicates 6/6 RoHS compliance.
Enable Logic
Pin Style
Feature Set
S - Standard
C - Current
monitor output
/ Trimmable
current limit
T - Buck
W - Buck /
Boost
K - 0.110"
N - 0.145"
R - 0.180"
Y - 0.250"
N - Negative
Application Notes
Contact SynQor for C - Feature Set availability.
A variety of application notes and technical white papers can
be downloaded in pdf format from our website.
Not all combinations make valid part numbers, please contact
SynQor for availability. See the Product Summary web page for
more options.
RoHS Compliance: The EU led RoHS (Restriction of Hazardous
Substances) Directive bans the use of Lead, Cadmium, Hexavalent
Chromium, Mercury, Polybrominated Biphenyls (PBB), and
Polybrominated Diphenyl Ether (PBDE) in Electrical and Electronic
Equipment. This SynQor product is 6/6 RoHS compliant. For
more information please refer to SynQor’s RoHS addendum
available at our RoHS Compliance / Lead Free Initiative web
PATENTS
SynQorꢀholdsꢀtheꢀfollowingꢀpatents,ꢀoneꢀorꢀmoreꢀofꢀwhichꢀ
mightꢀapplyꢀtoꢀthisꢀproduct:
page or e-mail us at rohs@synqor.com
.
ꢀ
ꢀ
ꢀ
ꢀ
5,999,417ꢀ
6,594,159ꢀ
6,927,987ꢀ
7,119,524ꢀ
6,222,742ꢀ
6,731,520ꢀ
7,050,309ꢀ
7,269,034ꢀ
6,545,890ꢀ
6,894,468ꢀ
7,072,190ꢀ
7,272,021ꢀ
6,577,109ꢀ
6,896,526ꢀ
7,085,146ꢀ
7,272,023
Contact SynQor for further information:
Phone:
Toll Free: 888-567-9596
Fax:
978-849-0600
Warranty
SynQor offers a three (3) year limited warranty. Complete warranty informa-
tion is listed on our website or is available upon request from SynQor.
978-849-0602
E-mail:
Web:
power@synqor.com
www.synqor.com
Information furnished by SynQor is believed to be accurate and reliable.
However, no responsibility is assumed by SynQor for its use, nor for any
infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any
patent or patent rights of SynQor.
Address: 155 Swanson Road
Boxborough, MA 01719
USA
Product # NQ60x60QGC20
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-NQ6060W Rev. B
03/16/09
Page 9
相关型号:
NQ60T60QGV20NYC-G
DC-DC Regulated Power Supply Module, 1 Output, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
NQ60W60EGV05NNS-G
DC-DC Regulated Power Supply Module, 1 Output, 300W, Hybrid, ROHS COMPLIANT, EIGHTH BRICK PACKAGE-8
SYNQOR
NQ60W60EGV05NRC-G
DC-DC Regulated Power Supply Module, 1 Output, 300W, Hybrid, ROHS COMPLIANT, EIGHTH BRICK PACKAGE-8
SYNQOR
©2020 ICPDF网 联系我们和版权申明