RHF1201KSO2 [STMICROELECTRONICS]
Rad-hard 12-bit 0.5 to 50 Msps A/D converter; 抗辐射12位0.5〜 50 Msps的A / D转换器型号: | RHF1201KSO2 |
厂家: | ST |
描述: | Rad-hard 12-bit 0.5 to 50 Msps A/D converter |
文件: | 总18页 (文件大小:194K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
RHF1201
Rad-hard 12-bit 0.5 to 50 Msps A/D converter
Features
SO-48 package
■ Wide sampling range: 0.5Msps to 50Msps
TM
■ Optimwatt adaptive power:
44mW @ 0.5Msps, 100mW @ 50Msps
■ Input range: 2 V differential
pp
■ SFDR up to 75dB @ FS = 50Msps,
Fin = 15MHz
■ 2.5V / 3.3V compatible digital I/O
Pin connections (top view)
■ Built-in reference voltage with external bias
capability
1
48
■ Hermetic package
■ Rad-hard: 300 kRad(Si) TID
■ Failure immune (SEFI) and latchup immune
2
(SEL) up to 120 MeV-cm /mg at 2.7V and
125°C
■ Qml-V qualified, smd 5962-05217
24
25
Applications
■ Digital communication satellites
■ Space data acquisition systems
■ Aerospace instrumentation
Specifically designed for optimizing power
consumption, the RHF1201 can dissipate as little
as 100mW at 50Msps, while maintaining a high
level of performance.
■ Nuclear and high-energy physics
It integrates a proprietary track-and-hold structure
to ensure IF-sampling applications up to 150
MHz.
Description
The RHF1201 is a 12-bit 50MHz maximum
sampling frequency analog to digital converter
using pure (ELDRS-free) CMOS 0.25µm
technology combining high performance, radiation
robustness and very low power consumption.
A voltage reference is integrated in the circuit to
simplify the design and minimize external
components. A tri-state capability is available on
the outputs to allow common bus sharing. Output
data can be coded in two different formats.
The RHF1201 is based on a pipeline structure
and digital error correction to provide excellent
static linearity and achieve 10.3 effective bits at
A Data Ready signal which is raised when the
data is valid on the output can be used for
synchronization purposes.
FS = 50Msps, and F = 15MHz.
in
The RHF1201 is available in -55° C to +125° C
temperature range, in a small 48-pin hermetic
SO-48 package.
June 2007
Rev 2
1/18
www.st.com
18
Contents
RHF1201
Contents
1
2
3
4
5
6
7
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Timing characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 6
Electrical characteristics (unchanged after 300kRad) . . . . . . . . . . . . . . 7
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.1
7.2
RHF1201 operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Driving the analog input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.2.1
7.2.2
7.2.3
Differential inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Single-ended input configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
IF-sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.3
Reference connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.3.1
7.3.2
Internal reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
External reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.4
7.5
7.6
Clock input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Power consumption optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Layout precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8
Definitions of specified parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Static parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Dynamic parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
9
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
10
11
2/18
RHF1201
Block diagram
1
Block diagram
Figure 1.
Block diagram
VREFP
+2.5V
+2.5V/3.3V
GNDA
IPOL
VIN
Reference
circuit
stage
1
stage
2
stage
n
INCM
VINB
VREFM
DFSB
SRC
OEB
Sequencer-phase shifting
Digital data correction
CLK
Timing
DR
DO
TO
Buffers
D11
OR
GND
2
Pin connections
Figure 2.
Pin connections (top view)
1
2
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
3/18
Pin descriptions
RHF1201
3
Pin descriptions
Table 1.
Pin
Pin descriptions
Name
Description
Observation
Pin
Name
Description
Observation
2.5 V/3.3 V CMOS
input
1
2
3
GNDBI
GNDBE
VCCBE
Digital buffer ground
0 V
25
SRC
Slew rate control input
2.5 V/3.3 V CMOS
input
Digital buffer ground
0 V
26
27
OEB
Output Enable input
Digital buffer power
supply
2.5 V/3.3 V CMOS
input
2.5 V/3.3 V
DFSB
Data Format Select input
4
5
NC
NC
Non connected
Non connected
28
29
AVCC
AVCC
Analog power supply
Analog power supply
2.5 V
2.5 V
CMOS output
(2.5 V/3.3 V)
6
OR
D11(MSB)
D10
D9
Out Of Range output
30
31
32
33
34
35
36
37
38
39
40
41
42
43
AGND
IPOL
Analog ground
0 V
Most Significant Bit
output
CMOS output
(2.5 V/3.3 V)
7
Analog bias current input
Top voltage reference
CMOS output
(2.5 V/3.3 V)
8
Digital output
Digital output
Digital output
Digital output
Digital output
Digital output
Digital output
Digital output
Digital output
Digital output
VREFP
VREFM
AGND
VIN
1 V
0 V
0 V
CMOS output
(2.5 V/3.3 V)
Bottom voltage
reference
9
CMOS output
(2.5 V/3.3 V)
10
11
12
13
14
15
16
17
18
19
D8
Analog ground
CMOS output
(2.5 V/3.3 V)
D7
Analog input
1 V
0 V
1 V
0 V
pp
pp
CMOS output
(2.5 V/3.3 V)
D6
AGND
VINB
Analog ground
CMOS output
(2.5 V/3.3 V)
D5
Inverted analog input
Analog ground
CMOS output
(2.5 V/3.3 V)
D4
AGND
INCM
AGND
AVCC
AVCC
DVCC
CMOS output
(2.5 V/3.3 V)
D3
Input common mode
Analog ground
0.5 V
0 V
CMOS output
(2.5 V/3.3 V)
D2
CMOS output
(2.5 V/3.3 V)
D1
Analog power supply
Analog power supply
Digital power supply
2.5 V
2.5 V
2.5 V
Least Significant Bit
output
CMOS output
(2.5 V/3.3 V)
D0(LSB)
DR
CMOS output
(2.5 V/3.3 V)
Data Ready output
20
21
NC
NC
Non connected
Non connected
44
45
DVCC
Digital power supply
Digital ground
2.5 V
0 V
DGND
Digital Buffer power
supply
2.5 V compatible
CMOS input
22
23
24
VCCBE
GNDBE
VCCBI
2.5 V/3.3 V
0 V
46
47
48
CLK
Clock input
Digital Buffer ground
DGND
DGND
Digital ground
Digital ground
0 V
0 V
Digital Buffer power
supply
2.5 V
4/18
RHF1201
Timing characteristics
4
Timing characteristics
Table 2.
Symbol
Timing table
Parameter
Test conditions
Min
Typ
Max
Unit
FS
Tck
DC
TC1
TC2
Sampling frequency
Sampling clock cycle
Clock duty cycle
0.5
20
45
10
8
50
MHz
ns
2000
65
FS = 45 Msps
50
%
Clock pulse width (high)
Clock pulse width (low)
1800
1800
ns
ns
Data output delay (fall of
clock to data valid)
Tod
Tpd
Tdr
10 pF load capacitance
4
5
6
ns
Data pipeline delay
5.5
5.5
0.5
5.5
cycles
cycles
Data ready delay after data
change
Falling edge of OEB to
digital output valid data
Ton
Toff
1
1
3
3
ns
ns
ns
ns
ns
ns
Rising edge of OEB to
digital output tri-state
SRC = 0 5 pF load
capacitance
2.8
5.7
2
T
Data rising time
rD
SRC = 1 5pF load
capacitance
SRC = 0 5pF load
capacitance
TfD
Data falling time
SRC = 1 5pF load
capacitance
4.3
Figure 3.
Timing diagram
N+2
N+3
N+1
N+4
N
N+5
N-3
N-1
N+6
N-2
CLK
Tpd + Tod
Tdr
OEB
Ton
Toff
Tod
DATA
OUT
N-9
N-8
N-7
N-6
N-5
N-4
N-3
N-1
N
DR
HZ state
5/18
Absolute maximum ratings and operating conditions
RHF1201
5
Absolute maximum ratings and operating conditions
Table 3.
Symbol
Absolute maximum ratings
Parameter
Values
Unit
AVCC
DVCC
VCCBI
VCCBE
IDout
Analog supply voltage(1)
Digital supply voltage(1)
0 to 3.3
0 to 3.3
0 to 3.3
0 to 3.6
-100 to 100
-65 to +150
22
V
V
Digital buffer supply voltage(1)
Digital buffer supply voltage(1)
Digital output current
V
V
mA
°C
°C/W
Tstg
Storage temperature
Rthjc
Junction - case thermal resistance
Electrostatic discharge
- HBM
ESD
2
kV
1. All voltage values, except differential voltage, are with respect to network ground terminal. The magnitude
of input and output voltages must never exceed -0.3 V or VCC +0.3 V.
Table 4.
Symbol
Operating conditions
Parameter
Test conditions
Min
Typ
Max
Unit
AVCC
DVCC
Analog supply voltage
Digital supply voltage
2.3
2.3
2.5
2.5
2.7
2.7
V
V
Digital internal buffer
supply
VCCBI
VCCBE
VREFP
2.3
2.3
0.5
2.5
2.5
1
2.7
3.4
V
V
V
Digital output buffer supply
Forced top voltage
reference
AVCC
Bottom internal reference
voltage
VREFM
0
0
0.5
V
6/18
RHF1201
Electrical characteristics (unchanged after 300kRad)
6
Electrical characteristics (unchanged after 300kRad)
Test conditions, unless otherwise specified are: AVCC = DVCC = V
= 2.5 V, FS = 50 Msps,
CCB
F = 2 MHz, V @ -1 dBSF, VREFP = Internal, V
= 0 V, T
= 25° C
in
IN
REFM
amb
Table 5.
Symbol
Analog inputs
Parameter
Test conditions
Min
Typ
Max
Unit
VIN-VINB
Cin
Full scale reference voltage
Input capacitance
2.0
7.0
Vpp
pF
Rin
Input resistance
Effective resolution
bandwidth(1)
ERB
95
MHz
1. See Section 8: Definitions of specified parameters on page 14 for more information.
Table 6.
Symbol
Reference voltage
Parameter
Test conditions
Min
Typ
Max
Unit
AVCC from 2.3V to 2.7V
VREFP
Top internal reference voltage
Input common mode voltage
0.82
0.95
1.16
V
Tmin = -55° C to
Tmax = 125° C(1)
AVCC=2.3 V to
AVCC=2.7 V
VINCM
0.43
052
0.67
V
Tmin = -55° C to
Tmax = 125° C(1)
VREFP
0.12
0.12
mV/°C
mV/°C
Tmin = -55° C to
Tmax = 125° C(1)
TempCo
Temperature coefficients
VINCM
Tmin = -55° C to
Tmax = 125° C(1)
1. Not fully tested over the temperature range. Guaranteed by sampling.
Table 7.
Symbol
Digital inputs and outputs
Parameter
Test conditions
Min
Typ
Max
Unit
Clock input
VIL
Logic "0" voltage
Logic "1" voltage
0
0.8
V
V
VIH
2.0
2.5
Digital inputs
0.25
VCCBE
VIL
Logic "0" voltage
Logic "1" voltage
0
V
V
0.75
VCCBE
VIH
VCCBE
7/18
Electrical characteristics (unchanged after 300kRad)
RHF1201
Unit
Table 7.
Symbol
Digital inputs and outputs (continued)
Parameter Test conditions
Min
Typ
Max
Digital outputs
VOL
VOH
Logic "0" voltage
Logic "1" voltage
IOL = -1mA
0
0.2
V
V
VCCBE
- 0.2
IOH = 1mA
IOZ
CL
High impedance leakage current
Output load capacitance
OEB set to VIH
-15
15
15
µA
pF
Table 8.
Symbol
Accuracy
Parameter
Test conditions
Min
Typ
Max
Unit
Fin = 2 MHz,
VIN @ +1 dBFS
OE
Offset error
±0.3
%
Fin = 2 MHz,
VIN @ +1 dBFS
DNL
Differential non linearity(1)
±0.5
±1.7
LSB
LSB
Fin = 2 MHz,
VIN @ +1 dBFS
INL
-
Integral non linearity(1)
Monotonicity and no missing codes
Guaranteed
1. See Section 8: Definitions of specified parameters on page 14 for more information.
Table 9.
Symbol
Dynamic characteristics
Parameter(1)
Test
Min
Typ
Max
Unit
conditions(2)
Fin = 15 MHz
Fin = 95 MHz
Fin = 145 MHz
Fin = 15 MHz
Fin = 95 MHz
Fin = 145 MHz
Fin = 15 MHz
-75
-70
-57
63
-63
dBc
SFDR
SNR
Spurious free dynamic range
Signal to noise ratio
dBc
dB
59
60
dB
59
-76
-72
-58
63
-64
dB
dB
THD
Total harmonics distortion
F
in = 95 MHz
Fin = 145 MHz
in = 15 MHz
F
59
dB
SINAD
ENOB
Signal to noise and distortion ratio Fin = 95 MHz
60
Fin = 145 MHz
Fin = 15 MHz
56.5
10.3
9.5
9.1
dB
bits
bits
9.7
Effective number of bits
Fin = 95 MHz
Fin = 145 MHz
1. See Section 8: Definitions of specified parameters on page 14 for more information.
2. VREFP = 1 V with external supply.
8/18
RHF1201
Application information
7
Application information
The RHF1201 is a high speed analog to digital converter based on a pipeline architecture
and a 0.25 µm CMOS process to achieve the best performance in terms of linearity and
power consumption.
The pipeline structure consists of 11 internal conversion stages in which the analog signal is
fed and sequentially converted into digital data. Signal input is sampled on the rising edge of
the clock.
The first 10 stages of the conversion include at each stage, an analog to digital converter, a
digital to analog converter, a Sample and Hold, and an amplifier with a gain of 2. A 1.5 bit
conversion resolution is also performed at each stage. The final stage is simply a
comparator. Each resulting LSB-MSB couple is then time shifted to recover from the delay
caused by the conversion. Digital data correction completes the processing by recovering
from the redundancy of the (LSB-MSB) couple at each stage. The corrected data is output
through the digital buffers.
The advantages of such a converter reside in the combination of pipeline architecture and
the most advanced technologies. The highest dynamic performances are achieved while
consumption remains at the lowest level.
7.1
RHF1201 operating modes
Extra functionalities are provided to simplify the application board as much as possible. The
operation modes offered by the RHF1201 are described in the following table.
Table 10. RHF1201 operating modes
Inputs
Outputs
Most significant
Analog input differential level
DFSB OEB SRC
OR
DR
bit (MSB)
(VIN-VINB
)
>
RANGE
H
H
H
L
L
L
L
L
L
L
H
X
X
X
X
X
X
X
X
X
H
L
H
H
L
CLK
CLK
CLK
D11
D11
D11
-RANGE
RANGE>
>
(VIN-VINB)
(VIN-VINB
)
>-RANGE
RANGE
(VIN-VINB
-RANGE
RANGE>
)
>
H
H
L
CLK D11 Complemented
CLK D11 Complemented
CLK D11 Complemented
>
(VIN-VINB
)
L
(VIN-VINB
)
>-RANGE
L
X
X
X
X
X
X
HZ
X
HZ
HZ
CLK
CLK
Low slew rate
High slew rate
X
Data format select (DFSB)
When set to low level (V ), the digital input DFSB provides a two’s complement digital
IL
output MSB. This can be of interest when performing some further signal processing.
When set to high level (V ), DFSB provides a standard binary output coding.
IH
9/18
Application information
RHF1201
Output enable (OEB)
When set to low level (V ), all digital outputs remain active and are in low impedance state.
IL
When set to high level (V ), all digital output buffers are in high impedance state while the
IH
converter goes on sampling. When OEB is set to a low level again, the data arrives on the
output with a very short T delay. This mechanism allows the chip select of the device.
on
Figure 3: Timing diagram on page 5 summarizes this functionality.
Slew rate control (SRC)
When set to high level (V ), all digital output currents are limited to a clamp value so that
IH
digital noise power is reduced to the minimum. When set to low level (V ), the output edges
IL
are twice as fast.
Out of range (OR)
This function is implemented on the output stage in order to set an “Out of Range” flag
whenever the digital data is over the full scale range.
Typically, there is a detection of all the data at ’0’ or all the data at ’1’. It sets an output signal
OR which is in low level state (V ) when the data stays within the range, or in high level
OL
state (V ) when the data is out of range.
OH
Data ready (DR)
The Data Ready output is an image of the clock being synchronized on the output data (D0
to D11). This is a very helpful signal that simplifies the synchronization of the measurement
equipment or of the controlling DSP.
As all other digital outputs, DR goes into high impedance state when OEB is set to high level
as shown in Figure 3: Timing diagram on page 5.
7.2
Driving the analog input
7.2.1
Differential inputs
The RHF1201is designed to obtain optimum performance when driven on differential inputs.
An RF transformer is an efficient way of achieving this high performance.
Figure 4: Differential input configuration describes the schematics. The input signal is fed to
the primary of the transformer, while the secondary drives both ADC inputs. The common
mode voltage of the ADC (INCM) is connected to the center-tap of the secondary of the
transformer in order to bias the input signal around this common voltage, internally set close
to 0.5V. The INCM is de-coupled to maintain a low noise level on this node. Our evaluation
board is mounted with a 1:1 ADT1-1 transformer from Minicircuits. You might also use a
higher impedance ratio (1:2 or 1:4) to reduce the driving requirement on the analog signal
source.
Each analog input can drive a 1 V amplitude input signal, so the resulting differential
pp
amplitude is 2 V .
pp
10/18
RHF1201
Application information
Figure 4.
Differential input configuration
ADT1-1
Analog source
1:1
VIN
RHF1201
50Ω
10-100pF
VINB
INCM
330pF
10nF
470nF
7.2.2
Single-ended input configuration
Some applications may require a single-ended input which is easily achieved with the
configuration shown in Figure 5: Single-ended input configuration.
The lack of accurate differential driving with its common-mode noise and even harmonics
cancellation advantages can degrade the rated RHF1201 performance. It is then
recommended to use a well de-coupled DC reference to bias the RHF1201 inputs.
In this case, one can use an AC-coupled analog input and set the DC analog level with high
value (10 kΩ to 100 kΩ) resistor connected to a proper DC source.
The internal references INCM (0.52 V) or REFP (1 V) can be used as proper DC sources.
Using 1 V DC with a single signal of 2 V input amplitude gives better SNR performance.
pp
Figure 5.
Single-ended input configuration
Signal source
10nF
VIN
10-100kΩ
50Ω
RHF1201
VINB
330pF
10nF
470nF
DC source or REFP
7.2.3
IF-sampling
The RHF1201 is specifically designed to meet sampling requirements for intermediate
frequency input signals. In particular, the Track-and-Hold in the first stage of the pipeline is
designed to minimize the linearity limitations as analog frequency increases.This is
achieved by making the input impedance independent from the input frequency.
As a result, the RHF1201 can maintain high performance up to an analog frequency of
150 MHz.
11/18
Application information
RHF1201
7.3
Reference connection
7.3.1
Internal reference
In the standard configuration, the ADC is biased with the internal reference voltage. The
pin is connected to Analog Ground while V is internally set to a voltage close to
V
REFM
REFP
1.0 V. It is recommended to de-couple the V
in order to minimize low and high
REFP
frequency noise. Refer to Figure 6: Internal reference setting for the schematics.
Figure 6.
Internal reference setting
~1V
470nF
330pF
10nF
VREFP
VIN
RHF1201
VINB
VREFM
7.3.2
External reference
It is possible to use an external reference voltage instead of the internal one for specific
applications requiring even better linearity or enhanced temperature behavior. In this case,
the amplitude of the external voltage must be at least equal to the internal one (1.0 V). You
can use an external voltage reference with the configuration shown in Figure 7: External
reference setting to obtain optimum performance.
Figure 7.
External reference setting
1kΩ
470nF
10nF
330pF
VCCA VREFP
VIN
RHF1201
VINB
external
reference
VREFM
This can be very helpful in multichannel applications for example to maintain a good
matching along the sampling frequency range.
12/18
RHF1201
Application information
7.4
Clock input
The quality of your converter is very dependent on your clock input accuracy, in terms of
aperture jitter; the use of a low jitter crystal controlled oscillator is recommended.
Further points to consider in your implementation are:
●
The input signal must be square-shaped with sharp edges of less than 1 ns.
●
At 45 Msps, the duty cycle must be between 45% and 65%; in any case, the high level
duration of Clock must be longer than 10 ns.
●
●
The clock power supplies must be independent from the ADC output supplies to avoid
digital noise modulation on the output.
When powered-on, the circuit needs several clock periods to reach its normal operating
conditions.
7.5
Power consumption optimization
The internal architecture of the RHF1201 makes it possible to optimize power consumption
according to the sampling frequency of the application. For this purpose, an External R
resistor is placed between the IPOL pin and the analog Ground. Therefore, the total
pol
dissipation can be adjusted across all the sampling range 0.5 Msps to 50 Msps to fulfil the
requirements of applications where power saving is a must.
For low sampling frequency, this value of resistor may be adjusted in order to decrease the
analog current without any degradation of dynamic performance.
Table 11 sums up the relevant data.
Table 11. Total power consumption optimization depending on R value
pol
FS (Msps)
pol (kΩ)
Optimized power (mW)
0.85
100
44
1.7
70
47
13.6
35
45
24
93
50
18
R
60
100
7.6
Layout precautions
●
Use of dedicated ground planes (analog, digital, internal and external buffer ones) on
the PCB is recommended for high speed circuit applications to provide low inductance
and low resistance common return.
●
●
●
●
●
The separation of the analog signal from the digital output part is mandatory to prevent
noise from coupling onto the input signal.
Power supply bypass capacitors must be placed as close as possible to the IC pins in
order to improve high frequency bypassing and reduce harmonic distortion.
All leads must be wide and as short as possible especially for the analog input in order
to decrease parasitic capacitance and inductance.
Keep the capacitive loading as low as possible at digital outputs, short lead lengths of
routing are essential to minimize currents when the output changes.
Choose component sizes as small as possible (SMD).
13/18
Definitions of specified parameters
RHF1201
8
Definitions of specified parameters
Static parameters
Static measurements are performed using the histograms method on a 2 MHz input signal,
sampled at 50 Msps, which is high enough to fully characterize the test frequency response.
The input level is +1 dBFS to saturate the signal.
Differential non linearity (DNL)
The average deviation of any output code width from the ideal code width of 1 LSB.
Integral non linearity (INL)
An ideal converter exhibits a transfer function which is a straight line from the starting code
to the ending code. The INL is the deviation from this ideal line for each transition.
Dynamic parameters
Dynamic measurements are performed by spectral analysis, applied to an input sine wave
of various frequencies and sampled at 50 Msps.
Spurious free dynamic range (SFDR)
The ratio between the power of the worst spurious signal (not always an harmonic) and the
amplitude of fundamental tone (signal power) over the full Nyquist band. It is expressed in
dBc.
Total harmonic distortion (THD)
The ratio of the rms sum of the first five harmonic distortion components to the rms value of
the fundamental line. It is expressed in dB.
Signal to noise ratio (SNR)
The ratio of the rms value of the fundamental component to the rms sum of all other spectral
components in the Nyquist band (f / 2) excluding DC, fundamental and the first five
s
harmonics. SNR is reported in dB.
Signal to noise and distortion ratio (SINAD)
Similar ratio as for SNR but including the harmonic distortion components in the noise figure
(not DC signal). It is expressed in dB.
The effective number of bits (ENOB) is easily deduced from the SINAD, using the formula:
SINAD = 6.02 × ENOB + 1.76 dB.
When the applied signal is not full scale (FS), but has an amplitude A , the SINAD
0
expression becomes:
SINAD = 6.02 × ENOB + 1.76 dB + 20 log (2A /FS)
0
The ENOB is expressed in bits.
14/18
RHF1201
Definitions of specified parameters
Effective resolution bandwidth
For a given sampling rate and clock jitter, the analog input frequency at which the SINAD is
reduced of 3 dB.
Pipeline delay
Delay between the initial sample of the analog input and the availability of the corresponding
digital data output on the output bus. Also called data latency. It is expressed as a number of
clock cycles.
15/18
Package information
RHF1201
9
Package information
Figure 8.
Ref.
SO-48 package
Dimensions
Millimeters
Inches
Typ.
Min.
Typ.
Max.
Min.
Max.
A
b
2.18
0.20
0.12
15.57
9.52
2.47
0.254
0.15
2.72
0.30
0.18
15.92
9.78
0.086
0.008
0.005
0.613
0.375
0.097
0.010
0.006
0.620
0.380
0.429
0.250
0.065
0.025
0.008
0.495
0.057
0.031
0.017
0.107
0.012
0.007
0.627
0.385
c
D
15.75
9.65
E
E1
E2
E3
e
10.90
6.35
6.22
1.52
6.48
1.78
0.245
0.060
0.255
0.070
1.65
0.635
0.20
f
L
12.28
1.30
0.66
0.25
12.58
1.45
12.88
1.60
0.92
0.61
0.483
0.051
0.026
0.010
0.507
0.063
0.036
0.024
P
Q
S1
0.79
0.43
16/18
RHF1201
Ordering information
10
Ordering information
Part number
Temperature range
Package
Marking
RHF1201KSO1
RHF1201KSO2
RHF1201KSO-01V
-55 °C to 125 °C
-55 °C to 125 °C
-55 °C to 125 °C
SO-48
SO-48
SO-48
RHF1201KSO1
RHF1201KSO2
F0521701VXC
11
Revision history
Date
Revision
Changes
01-Sep-2006
1
Initial release in new format.
Updated failure immune and latchup immune value to 120 MeV-
2
cm /mg.
29-Jun-2007
2
Updated package mechanical data.
Removed reference to non rad-hard components from Section 7.3.2:
External reference on page 12.
17/18
RHF1201
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
18/18
相关型号:
©2020 ICPDF网 联系我们和版权申明