LD49150PT12R [STMICROELECTRONICS]
1.5A Very low drop for low output voltage regulator; 1.5A非常低压降的低输出电压稳压器
| 型号： | LD49150PT12R |
| 厂家： | 
ST |
| 描述： | 1.5A Very low drop for low output voltage regulator |
| 文件： | 总20页 (文件大小：610K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LD49150
1.5A Very low drop for low output voltage regulator
Feature summary
■ Input voltage range:
VI = 1.4V to 5.5V
VBIAS = 3V to 6V
■ Stable with ceramic capacitor
1.5% initial tolerance
■
■ Maximum dropout voltage (VI - VO) of 200mV
PPAK
over temperature
■ Adjustable output voltage down to 0.8V
5.5V and the bias supply requires between 3V
and 6V for proper operation. The LD49150 offers
fixed output voltages from 0.8V to 1.8V and
adjustable output voltages down to 0.8V.
■ Ultra fast transient response (up to 10MHz
bandwidth)
■ Excellent line and load regulation
specifications
The LD49150 requires a minimum output
capacitance for stability, and work optimally with
small ceramic capacitors.
■ Logic controlled shutdown option
■ Thermal shutdown and current limit protection
■ Junction temperature range: –25°C to 125°C
Applications
Description
■ Graphics processors
The LD49150 is a high-bandwidth, low-dropout,
1.5A voltage regulator, ideal for powering core
voltages of low-power microprocessors. The
LD49150 implements a dual supply configuration
allowing for very low output impedance and very
fast transient response. The LD49150 requires a
bias input supply and a main input supply,
■ PC Add-In Cards
■ Microprocessor core voltage supply
■ Low voltage digital ICs
■ High Efficiency Linear power supplies
■ SMPS post regulators
allowing for ultra-low input voltages on the main
supply rail. The input supply operates from 1.4V to
Order codes
Part number
Package
PPAK (Tape&Reel)
Packaging
LD49150PT08R (1)
LD49150PT10R
LD49150PT12R
2500 parts per reel
2500 parts per reel
2500 parts per reel
PPAK (Tape&Reel)
PPAK (Tape&Reel)
1. Adjustable Version.
April 2007
Rev. 1
1/20
www.st.com
20
Contents
LD49150
Contents
1
2
3
4
5
6
7
8
Typical application circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Alternative application circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Application hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
Input supply voltage (V ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IN
Bias supply voltage (V
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
BIAS
External capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Output capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Minimum load current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
V
and V
power sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
BIAS
IN
Power dissipation/heatsinking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Heatsinking PPAK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Adjustable regulator design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.10 Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
9
10
2/20
LD49150
Typical application circuits
1
Typical application circuits
Figure 1. Adjustable version
Figure 2. Fixed version with Enable
3/20
Alternative application circuits
LD49150
2
Alternative application circuits
Figure 3. Single supply voltage solution
Figure 4. LD49150 plus DC/DC pre-regulator to reduce power dissipation
4/20
LD49150
Pin configuration
3
Pin configuration
Figure 5. Pin connections (top view)
Table 1.
Pln n°
1
Pin description
Symbol
Note
EN
ADJ
VIN
Enable (Input): Logic High = Enable, Logic Low = Shutdown.
Adjustable regulator feedback input. Connect to resistor voltage divider.
Input voltage which supplies current to the output power device.
Ground (TAB is connected to ground).
2
3
4
GND
VOUT
Regulator output.
Input bias voltage for powering all circuitry on the regulator with the exception of the output
power device.
VBIAS
5
5/20
Diagram
LD49150
4
Diagram
Figure 6. Block diagram
6/20
LD49150
Maximum ratings
5
Maximum ratings
Table 2.
Absolute maximum ratings
Parameter
Symbol
Value
Unit
VIN
Supply voltage
-0.3 to 7
V
-0.3 to VIN + 0.3
-0.3 to VBIAS + 0.3
VOUT
Output voltage
V
VBIAS
VEN
PD
BIAS Supply voltage
Enable input voltage
Power dissipation
-0.3 to 7
-0.3 to 7
V
V
Internally Limited
-50 to 150
TSTG
Storage temperature range
°C
Note: 1 Absolute Maximum Ratings are those values beyond which damage to the device may occur.
Functional Operation under these conditions is not implied.
2 All the values are referred to ground.
Table 3.
Symbol
Operating ratings
Parameter
Value
Unit
V
VIN
VOUT
VBIAS
VEN
TJ
Supply voltage
1.4 to 5.5
0.8 to 4.5
3 to 6
Output voltage
V
BIAS Supply voltage
Enable input voltage
V
0 to VBIAS
V
Junction temperature range
-25 to 125
°C
7/20
Electrical characteristics
LD49150
6
Electrical characteristics
Table 4.
Electrical characteristics
(TJ = -25°C to 125 °C, VBIAS = VO+2.1V (1); VI = VO+1V; VEN = VBIAS (2), IO = 10mA; CI = 1µF;
CO = 10µF; CBIAS = 1µF; unless otherwise specified. Typical values are referred to TJ = 25°C).
Symbol
Parameter
Test conditions
Min.
Typ.
Max. Unit
TJ = 25°C, fixed voltage options
-1.5
-3
1.5
%
3
VO
Output voltage accuracy
Over temperature range
VI = VO+1V to 5.5V
VLINE
VLOAD
VDROP
VDROP
Line regulation
-0.1
0.1
1
%/V
%
IL = 0mA to 3A, VBIAS ≥ 3V
IL = 1.5A
IL = 1.5A (1)
IL = 0mA
Load regulation
Dropout voltage (VI - VO)
200
2.1
6
mV
V
Dropout voltage (VBIAS- VO)
1.5
4
IGND
IGND_SHD
IVBIAS
IL
Ground pin current
mA
µA
mA
A
IL = 1.5A
4
6
VEN ≤0.4V (2)
IL = 0mA
Ground pin current in shutdown
Current through VBIAS
Current limit
5
3
3
5
IL = 1.5A
5
VO = 0V
2.5
1.4
Enable Input (2)
Regulator Enable
Regulator Shutdown
Enable input threshold (fixed
voltage only)
VEN
V
0.4
1
IEN
Enable pin input current
0.1
µA
Reference
TJ = 25°C
0.788
0.776
0.8
0.8
0.812
0.824
VREF
Reference voltage
V
Over temperature range
VI = 2.5V 0.5V, VO = 1V,
F = 120Hz, VBIAS = 3.3V
SVR
Supply voltage rejection
68
dB
1. For VO ≤1V, V
dropout specification does not apply due to a minimum 3V V
input.
BIAS
BIAS
2. Fixed output voltage version only.
8/20
LD49150
Typical characteristics
7
Typical characteristics
Figure 7.
Reference voltage vs temperature Figure 8.
Output voltage vs temperature
Figure 9.
Load regulation vs temperature
Figure 10. Line regulation vs temperature
Figure 11. Output voltage vs input voltage
Figure 12. Dropout voltage (VIN-VOUT) vs
temperature
9/20
Typical characteristics
LD49150
Figure 13. Dropout voltage (VIN-VOUT) vs
temperature
Figure 14. VBIAS pin current vs temperature
Figure 15. Noise vs frequency
Figure 16. Quiescent current vs temperature
Figure 17. Supply voltage rejection vs output Figure 18. Stability region vs COUT & High ESR
current
10/20
LD49150
Typical characteristics
Figure 19. Stability region vs COUT & Low ESR Figure 20. VBIAS & VIN Start Up transient
response (VIN and VBIAS Start Up at
the same time)
V
=V
=V =3.1V, V
=1V, C
=1µF
OUT
IN
BIAS
INH
OUT
Figure 21. VIN Start Up transient response
(VBIAS Start Up before VIN)
Figure 22. VIN Start Up transient response
(VBIAS Start Up before VIN)
V
=2.5V, V
=V =3.1V, V
=1V, C
=1µF
V
=2.5V, V
=V =3.1V, V
=1V, C
=1µF
OUT
IN
BIAS
INH
OUT
OUT
IN
BIAS
INH
OUT
11/20
Typical characteristics
LD49150
Figure 23. VIN Start Up transient response
(VBIAS Start Up before VIN and
VINH=VIN)
V
=V =2.5V, V
=3.1V, V
=1V, C
=1µF
OUT
IN
INH
BIAS
OUT
12/20
LD49150
Application hints
8
Application hints
The LD49150 is an ultra-high performance, low dropout linear regulator, designed for high
current application that requires fast transient response. The LD49150 operates from two input
voltages, to reduce dropout voltage. The LD49150 is designed so that a minimum of external
component are necessary.
8.1
8.2
Input supply voltage (V )
IN
VIN provides the power input current to the LD49150. The minimum input voltage can be as low
as 1.4V, allowing conversion from very low voltage supplies to achieve low output voltage levels
with very low power dissipation.
Bias supply voltage (V
)
BIAS
The LD49150 control circuitry is supplied the VBIAS pin which requires a very low bias current
(3mA typ.) even at the maximum output current level (1.5A). A bypass capacitor on the bias pin
is recommended to improve the performance of the LD49150 during line and load transient.
The small ceramic capacitor from VBIAS to ground reduces high frequency noise that could be
injected into the control circuitry from the bias rail. In typical applications a 1µF ceramic chip
capacitor may be used. The VBIAS input voltage must be 2.1V above the output voltage, with a
minimum VBIAS input voltage of 3V.
8.3
8.4
External capacitors
To assure regulator stability, input and output capacitors are required as shown in the typical
application circuit.
Output capacitor
The LD49150 requires a minimum output capacitance to maintain stability. A ceramic chip
capacitor of at least 1µF is required. However, specific capacitor selection could be needed to
ensure the transient response. A 1µF ceramic chip capacitor satisfies most applications but
10µF is recommended to ensure better transient performances. In applications where the VIN
level is close to the maximum operating voltage (VIN>4V), it is strongly recommended to use an
output capacitors of, at least, 10µF in order to avoid over-voltage stress on the Input/output
power pins during short circuit conditions due to parasitic inductive effect. The output capacitor
must be located as close as possible to the output pin of the LD49150. The ESR (equivalent
series resistance) of the output capacitor must be within the "STABLE" region as shown in the
typical characteristics figures. Both ceramic and tantalum capacitors are suitable.
8.5
Minimum load current
The LD49150 does not require a minimum load to maintain output voltage regulation.
13/20
Application hints
LD49150
8.6
V and V
power sequencing
BIAS
IN
In common applications where the power on transient of VIN and VBIAS voltages are not
particularly fast (T >100µs), no power sequencing is required. Where voltage transient input
r
(T <100µs) is very fast, it is recommended to have the VIN voltage present before or, at least, at
r
the same time as the VBIAS voltage in order to avoid overvoltage spikes during the power on
transient (refer to the figures in the typical characteristics). Where VIN transient input
(T <<100µs) is very fast for the fixed VOUT versions, it is possible to avoid start-up overvoltage
r
spikes by pulling the VINH pin up to VIN voltage (refer to relative typical characteristics figures at
pages 11 and 12).
8.7
Power dissipation/heatsinking
A heatsink may be required depending on the maximum power dissipation and maximum
ambient temperature of the application. Under all possible conditions, the junction temperature
must be within the range specified under operating conditions. The total power dissipation of
the device is given by:
PD = VIN x IIN + VBIAS x IBIAS - VOUT x IOUT
Where:
●
●
●
●
VIN, Input supply voltage
VBIAS, Bias supply voltage
VOUT, Output voltage
IOUT, Load current
From this data, we can calculate the thermal resistance (θSA) required for the heat sink using
the following formula:
θ
SA = (TJ - TA/PD) - (θJC + θCS
)
The maximum allowed temperature rise (TRmax) depends on the maximum ambient
temperature (TAmax) of the application, and the maximum allowable junction temperature
(TJmax):
T
Rmax = TJmax - TAmax
The maximum allowable value for junction to ambient thermal resistance, θJA, can be
calculated using the formula:
θ
JAmax = TRmax / PD
This part is available for the PPAK package.
The thermal resistance depends on the amount of copper area or heat sink, and on air flow. If
the maximum allowable value of θJA calculated above is ≥100 °C/W for the PPAK package, no
heatsink is needed since the package can dissipate enough heat to satisfy these requirements.
If the value for allowable θJA falls below these limits, a heat sink is required as described below.
14/20
LD49150
Application hints
8.8
Heatsinking PPAK package
The PPAK package uses the copper plane on the PCB as a heatsink. The tab of these
packages is soldered to the copper plane for heat sinking. It is also possible to use the PCB
ground plane a heatsink. This area can be the inner GND layer of a multi-layer PCB, or, in a
dual layer PCB, it can be an unbroken GND area on the opposite side where the IC is situated
with a dissipating area thermally connected through vias holes, filled by solder.
Figure 26 shows a curve for θJA of the PPAK package for different copper area sizes, using a
typical PCB with 1/16 in thick G10/FR4.
Figure 24. θJA vs Copper Area for PPAK package
8.9
Adjustable regulator design
The LD49150 adjustable version allows fixing output voltage anywhere between 0.8V and 4.5V
using two resistors as shown in the typical application circuit. For example, to fix the R1 resistor
value between VOUT and the ADJ pin, the resistor value between ADJ and GND (R2) is
calculated by:
R2 = R1 [0.8/(VOUT - 0.8)]
Where VOUT is the desired output voltage.
It is suggested to use R1 values lower than 10KΩto obtain better load transient performances.
Even, higher values up to 100KΩ are suitable.
8.10 Enable
The fixed output voltage versions of LD49150 feature an active high Enable input (EN) that
allows on-off control of the regulator. The EN input threshold is guaranteed between 0.4V and
1.4V, for simple logic interfacing. The regulator is set in shut down mode when VEN<0.4V and it
is in operating mode (VOUT activated) when VEN>1.4V. If not in use, the EN pin must be tied
directly to the VIN to keep the regulator continuously activated. The En pin must not be left at
high impedance.
15/20
Package mechanical data
LD49150
9
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK® packages.
These packages have a Lead-free second level interconnect. The category of second Level
Interconnect is marked on the package and on the inner box label, in compliance with JEDEC
Standard JESD97. The maximum ratings related to soldering conditions are also marked on
the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at:
www.st.com.
16/20
LD49150
Package mechanical data
PPAK MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
A1
A2
B
2.2
0.9
0.03
0.4
5.2
0.45
0.48
6
2.4
1.1
0.23
0.6
5.4
0.6
0.6
6.2
0.086
0.035
0.001
0.015
0.204
0.017
0.019
0.236
0.094
0.043
0.009
0.023
0.212
0.023
0.023
0.244
B2
C
C2
D
D1
E
5.1
0.201
6.4
6.6
0.252
0.260
E1
e
4.7
0.185
0.050
1.27
G
4.9
5.25
2.7
10.1
1
0.193
0.093
0.368
0.206
0.106
0.397
0.039
0.039
G1
H
2.38
9.35
L2
L4
L5
L6
0.8
2.8
0.031
0.110
0.6
1
1
0.023
0.039
0078180-E
17/20
Package mechanical data
LD49150
Tape & Reel DPAK-PPAK MECHANICAL DATA
mm.
TYP
inch
TYP.
DIM.
MIN.
MAX.
330
MIN.
MAX.
12.992
0.519
A
C
12.8
20.2
60
13.0
13.2
0.504
0.795
2.362
0.512
D
N
T
22.4
7.00
10.60
2.75
4.1
0.882
0.2.76
0.417
0.105
0.161
0.319
Ao
Bo
Ko
Po
P
6.80
10.40
2.55
3.9
6.90
10.50
2.65
4.0
0.268
0.409
0.100
0.153
0.311
0.272
0.413
0.104
0.157
0.315
7.9
8.0
8.1
18/20
LD49150
Revision history
10 Revision history
Table 5.
Date
18-Apr-2007
Revision history
Revision
Changes
1
Initial release.
19/20
LD49150
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
20/20
相关型号：
©2020 ICPDF网 联系我们和版权申明