LM4565FVJ-E2 [ROHM]
Low Noise Operational Amplifier;
| 型号： | LM4565FVJ-E2 |
| 厂家： | 
ROHM |
| 描述： | Low Noise Operational Amplifier 放大器 光电二极管 |
| 文件： | 总28页 (文件大小：696K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Datasheet
Operational Amplifiers
Low Noise Operational Amplifier
LM4565xxx
Key Specifications
Operating Supply Voltage:
Temperature Range:
Voltage Gain (RL=2kΩ):
Slew Rate:
General Description
±2V to ±18V
-40°C to +85°C
100dB(Typ)
5.0V/μs (Typ)
10MHz (Typ)
The LM4565xxx are low nose operational amplifiers
with high voltage gain and wide bandwidth. They have
good performance of input referred noise voltage
(5nV/ Hz ) and total harmonic distortion (0.0002%).
These are suitable for audio applications and active
filter.
Gain Bandwidth:
Input Referred Noise Voltage:
5nV/ Hz (Typ)
Package
W(Typ) xD(Typ) xH(Max)
Features
High Voltage Gain
High Slew Rate
Low Input Referred Noise Voltage
Low Total Harmonic Distortion
Wide Gain Bandwidth
SOP-8
SOP-J8
SSOP-B8
TSSOP-B8
MSOP8
5.00mm x 6.20mm x 1.71mm
4.90mm x 6.00mm x 1.65mm
3.00mm x 6.40mm x 1.35mm
3.00mm x 6.40mm x 1.20mm
2.90mm x 4.00mm x 0.90mm
3.00mm x 4.90mm x 1.10mm
TSSOP-B8J
Application
Audio Application
Consumer Equipment
Active Filter
Pin Configuration
LM4565F
: SOP8
LM4565FJ
LM4565FV
LM4565FVT
LM4565FVM
LM4565FVJ
: SOP-J8
: SSOP-B8
: TSSOP-B8
: MSOP8
: TSSOP-B8J
Pin No.
Pin Name
OUT1
-IN1
1
2
3
4
5
6
7
8
VCC
OUT2
-IN2
1
2
8
7
OUT1
-IN1
CH1
- +
+IN1
VEE
3
4
+IN1
VEE
6
5
CH2
+ -
+IN2
+IN2
-IN2
OUT2
VCC
Figure1. Pin Configuration
○Product structure：Silicon monolithic integrated circuit ○This product has no designed protection against radioactive rays.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･14･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
1/24
Datasheet
LM4565xxx
Ordering Information
L
M
4
5
6
5 x x x
-
x x
Part Number
LM4565xxx
Package
Packaging and forming specification
E2: Embossed tape and reel
(SOP8/SOP-J8/SSOP-B8/TSSOP-B8/TSSOP-B8J)
TR: Embossed tape and reel
(MSOP8)
F
: SOP8
FJ
FV
: SOP-J8
: SSOP-B8
FVT : TSSOP-B8
FVM : MSOP8
FVJ : TSSOP-B8J
Line-up
Topr
Package
Orderable Part Number
SOP8
Reel of 2500
Reel of 2500
Reel of 2500
Reel of 3000
Reel of 3000
Reel of 2500
LM4565F-E2
SOP-J8
LM4565FJ-E2
LM4565FV-E2
LM4565FVT-E2
LM4565FVM-TR
LM4565FVJ-E2
SSOP-B8
TSSOP-B8
MSOP8
-40°C to +85°C
TSSOP-B8J
Absolute Maximum Ratings (TA=25°C)
Parameter
Supply Voltage
Symbol
Rating
Unit
V
VCC - VEE
SOP8
+36
0.68(Note 1,5)
0.67(Note 2,5)
0.62(Note 3,5)
0.62(Note 3,5)
0.58(Note 4,5)
0.58(Note 4,5)
+36
SOP-J8
SSOP-B8
TSSOP-B8
MSOP8
TSSOP-B8J
VID
Power Dissipation
PD
W
Differential Input Voltage (Note 6)
Input Common-mode
Voltage Range
V
V
VICM
(VEE - 0.3) to (VEE + 36)
Operating Voltage
Vopr
Topr
Tstg
±2 to ±18
- 40 to +85
- 55 to +150
V
Operating Temperature
Storage Temperature
°C
°C
Maximum
Junction Temperature
TJmax
+150
°C
(Note 1) When used at temperature above TA=25°C, reduce by 5.5mW/°C.
(Note 2) When used at temperature above TA=25°C, reduce by 5.4mW/°C.
(Note 3) When used at temperature above TA=25°C, reduce by 5.0mW/°C.
(Note 4) When used at temperature above TA=25°C, reduce by 4.7mW/°C.
(Note 5) Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm).
(Note 6) The differential input voltage is the voltage difference between inverting input and non-inverting input.
Input terminal voltage is set to more than VEE.
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over
the absolute maximum ratings.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
2/24
Datasheet
LM4565xxx
Electrical Characteristics:
○LM4565xxx (Unless otherwise specified VCC = +15V, VEE = -15V)
Limit
Typ
Temperature
Parameter
Symbol
Unit
Conditions
Range
Min
-
Max
1.5
Input Offset Voltage (Note 7)
Input Offset Current (Note 7)
Input Bias Current (Note 7)
VIO
IIO
IB
25°C
0.5
2
mV
nA
nA
RS≤10kΩ
25°C
25°C
-
-
50
-
-
70
250
25°C
-
4.5
-
7
RL=∞, All Op-Amps
+IN=0V
Supply Current (Note 8)
ICC
mA
Full range
25°C
-
8.5
Large Signal Voltage Gain
Maximum Output Voltage
AV
86
±12
±11
±12
-
100
±14
±12.5
±14
130
-
-
-
-
-
dB
V
RL≥2kΩ, OUT=±10V
25°C
RL≥2kΩ
IO=25mA
-
VOM
25°C
V
Input Common-mode Voltage Range
Output Source Current (Note 9)
VICM
25°C
V
+IN=1V, -IN=0V
OUT=-15V
1CH is short circuit
+IN=0V, -IN=1V
OUT=+15V
ISOURCE
25°C
mA
mA
dB
dB
Output Sink Current (Note 9)
Common-mode Rejection Ratio
Power Supply Rejection Ratio
Slew Rate
ISINK
CMRR
PSRR
SR
25°C
25°C
25°C
25°C
25°C
25°C
25°C
-
160
100
100
5
-
-
-
-
1CH is short circuit
80
82
-
RL≤10kΩ
RL≤10kΩ
V/μs RL=2kΩ, CL=100pF
MHz RL=2kΩ
Unity Gain Frequency
Gain Bandwidth
fT
4
GBW
θ
-
-
-
-
-
-
10
-
-
-
-
-
-
MHz RL=2kΩ, f=100kHz
Phase Margin
40
deg
RL=2kΩ
AV=40dB
µVrms RS=100Ω
0.6
5
DIN-AUDIO
Input Referred Noise Voltage
VN
25°C
AV=40dB, VICM=0V
RS=100Ω, f=1kHz
nV/ Hz
%
Av=20dB, f=1kHz
OUT=5Vrms
Total Harmonic Distortion + Noise
Channel Separation
THD+N
CS
25°C
25°C
0.0002
110
AV=40dB, f=1kHz
OUT=1Vrms
dB
(Note 7) Absolute value.
(Note 8) Full range: TA=-40°C to +85°C
(Note 9) Please consider the power dissipation when selecting the output current.
When the output terminal is continuously shorted the output current reduces the internal temperature by flushing.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
3/24
Datasheet
LM4565xxx
Description of Electrical Characteristics
Described here are the terms of electric characteristics used in this datasheet. Items and symbols used are also shown.
Note that item name, symbol and their meaning may differ from those on other manufacturer’s document or general
documents.
1. Absolute maximum ratings
Absolute maximum rating items indicate the condition which must not be exceeded. Application of voltage in excess of absolute
maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics.
(1) Supply Voltage (VCC/VEE)
Indicates the maximum voltage that can be applied between the positive power supply terminal and negative power
supply terminal without deterioration or destruction of characteristics of internal circuit.
(2) Differential Input Voltage (VID)
Indicates the maximum voltage that can be applied between non-inverting and inverting terminals without damaging
the IC.
(3) Input Common-mode Voltage Range (VICM
)
Indicates the maximum voltage that can be applied to the non-inverting and inverting terminals without deterioration
or destruction of electrical characteristics. Input common-mode voltage range of the maximum ratings does not assure
normal operation of IC. For normal operation, use the IC within the input common-mode voltage range characteristics.
(4) Power dissipation (PD)
Indicates the power that can be consumed by the IC when mounted on a specific board at the ambient temperature 25℃
(normal temperature). As for package product, PD is determined by the temperature that can be permitted by the IC in
the package (maximum junction temperature) and the thermal resistance of the package.
2. Electrical characteristics item
(1) Input Offset Voltage (VIO)
Indicates the voltage difference between non-inverting terminal and inverting terminals. It can be translated into the
input voltage difference required for setting the output voltage at 0 V.
(2) Input Offset Current (IIO)
Indicates the difference of input bias current between the non-inverting and inverting terminals.
(3) Input Bias Current (IB)
Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias currents at
the non-inverting and inverting terminals.
(4) Supply Current (ICC
)
Indicates the current that flows within the IC under specified no-load conditions.
(5) Large Signal Voltage Gain (AV)
Indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal
and inverting terminal. It is normally the amplifying rate (gain) with reference to DC voltage.
Av = (Output voltage) / (Differential Input voltage)
(6) Maximum Output Voltage (VOM
)
Indicates the voltage range that the IC can output under specified load condition. It is typically divided into high-level
output voltage and low-level output voltage. High-level output voltage indicates the upper limit of output voltage.
Low-level output voltage indicates the lower limit.
(7) Input Common-mode Voltage Range (VICM
Indicates the input voltage range where IC operates normally.
(8) Output Source Current/ Output Sink Current (ISOURCE / ISINK
)
)
The maximum current that can be output from the IC under specific output conditions. The output source current
indicates the current flowing out from the IC, and the output sink current indicates the current flowing into the IC.
(9) Common-mode Rejection Ratio (CMRR)
Indicates the ratio of fluctuation of input offset voltage when the input common-mode voltage is changed. It is
normally the fluctuation of DC.
CMRR = (Change of Input common-mode voltage)/(Input offset fluctuation)
(10) Power Supply Rejection Ratio (PSRR)
Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed.
It is normally the fluctuation of DC.
PSRR= (Change of power supply voltage)/(Input offset fluctuation)
(11) Slew Rate (SR)
Indicates the ratio of the change in output voltage with time when a step input signal is applied.
(12) Unity Gain Frequency (fT)
Indicates a frequency where the voltage gain of operational amplifier is 1.
(13) Gain Bandwidth (GBW)
Indicates to multiply by the frequency and the gain where the voltage gain decreases 6dB/octave.
(14) Phase Margin (θ)
Indicates the margin of phase from 180 degree phase lag at unity gain frequency.
(15) Input Referred Noise Voltage (VN)
Indicates a noise voltage generated inside the operational amplifier reflected back to an ideal voltage source
connected in series with the input terminal.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
4/24
Datasheet
LM4565xxx
(16) Total Harmonic Distortion + Noise (THD+N)
Indicates the fluctuation of input offset voltage or that of output voltage with reference to the change of output voltage
of driven channel.
(17) Channel Separation (CS)
Indicates the fluctuation in the output voltage of the driven channel with reference to the change of output voltage of
the channel which is not driven.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
5/24
Datasheet
LM4565xxx
Typical Performance Curves
○LM4565xxx
1.0
8
7
6
5
4
3
2
1
0
0.8
0.6
0.4
0.2
0.0
-40°C
LM4565F
LM4565FJ
LM4565FV
LM4565FVT
25°C
LM4565FVM
LM4565FVJ
85°C
85
0
25
50
75
100
125
150
±0
±3
±6
±9
±12
±15
±18
Ambient Temperature [°C]
Supply Voltage [V]
Figure 2.
Figure 3.
Power Dissipation vs Ambient Temperature
(Derating Curve)
Supply Current vs Supply Voltage
8
20
15
10
5
7
6
5
4
3
2
1
0
-40°C
25°C
85°C
0
85°C
25°C
-5
-40°C
-10
-15
-20
±0
±5
±10
±15
±20
-50
-25
0
25
50
75
100
Supply Voltage [V]
Ambient Temperature [°C]
Figure 4.
Figure 5.
Supply Current vs Ambient Temperature
(VCC/VEE=±15V)
Maximum Output Voltage vs Supply Voltage
(RL=2kΩ, TA=25°C)
(*)The above characteristics are measurements of typical sample, they are not guaranteed.
www.rohm.com
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
©2012 ROHM Co., Ltd. All rights reserved.
6/24
TSZ22111･15･001
Datasheet
LM4565xxx
Typical Performance Curves (Reference data) – continued
○LM4565xxx
20
15
10
5
20
15
10
5
-40°C
25°C
85°C
0
0
85°C
25°C
-5
-5
-40°C
-10
-15
-20
-10
-15
-20
±0
±5
±10
±15
±20
-50
-25
0
25
50
75
100
Supply Voltage [V]
Ambient Temperature [°C]
Figure 6.
Figure 7.
Maximum Output Voltage vs Ambient Temperature
Maximum Output Voltage vs Supply Voltage
(IO=25mA, TA=25°C)
(VCC/VEE=±15V, RL=2KΩ)
20
15
10
5
3
2
1
0
0
-5
-1
-2
-3
-10
-15
-20
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature [°C]
Ambient Temperature [°C]
Figure 8.
Figure 9.
Maximum Output Voltage vs Ambient Temperature
(VCC/VEE=±15V, IO=25mA)
Input Offset Voltage vs Ambient Temperature
(VCC/VEE=±15V)
(*)The above characteristics are measurements of typical sample, they are not guaranteed.
www.rohm.com
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
©2012 ROHM Co., Ltd. All rights reserved.
7/24
TSZ22111･15･001
Datasheet
LM4565xxx
Typical Performance Curves (Reference data) – continued
○LM4565xxx
150
125
100
75
3
2
1
-40°C
0
25°C
85°C
50
-1
-2
-3
25
0
-50
-25
0
25
50
75
100
-15
-10
-5
0
5
10
15
Input Common Mode Voltage [V]
Ambient Temperature [°C]
Figure 10.
Figure 11.
Input Offset Voltage vs Input Common mode Voltage
(VCC/VEE=±15V)
Input Bias Current vs Ambient Temperature
(VCC/VEE=±15V)
140
130
120
110
100
90
130
120
110
100
90
80
80
70
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature [°C]
Ambient Temperature [°C]
Figure 12.
Figure 13.
Large Signal Voltage Gain vs Ambient Temperature
Common Mode Rejection Ratio vs Ambient Temperature
(VCC/VEE=±15V)
(VCC/VEE=±15V, RL=2kΩ)
(*)The above characteristics are measurements of typical sample, they are not guaranteed.
www.rohm.com
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
©2012 ROHM Co., Ltd. All rights reserved.
8/24
TSZ22111･15･001
Datasheet
LM4565xxx
Typical Performance Curves (Reference data) - continued
○LM4565xxx
10
8
140
120
100
80
6
4
2
0
60
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Ambient Temperature [°C]
Ambient Temperature [°C]
Figure 14.
Figure 15.
Power Supply Rejection Ratio vs Ambient Temperature
Slew Rate L-H vs Ambient Temperature
(VCC/VEE=±15V, RL=2kΩ, CL=100pF)
10
8
100
80
60
40
20
0
200
150
100
50
Phase
6
Gain
4
2
0
0
102
103
104
105
106
107
108
-50
-25
0
25
50
75
100
Frequency [Hz]
Ambient Temperature [°C]
Figure 16.
Figure 17.
Slew Rate H-L vs Ambient Temperature
(VCC/VEE=±15V, RL=2kΩ, CL=100pF)
Voltage Gain・Phase vs Frequency
(VCC/VEE=±15V, RL=2kΩ)
(*)The above characteristics are measurements of typical sample, they are not guaranteed.
www.rohm.com
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
©2012 ROHM Co., Ltd. All rights reserved.
9/24
TSZ22111･15･001
Datasheet
LM4565xxx
Typical Performance Curves (Reference data) - continued
○LM4565xxx
1
0.1
30
25
20
15
10
5
0.01
0.001
0.0001
20Hz
1kHz
20kHz
0
1
10
102
103
104
105
0.01
0.1
1
10
100
Frequency[Hz]
Output Voltage [Vrms]
Figure 18.
Figure 19.
Total Harmonic Distortion vs Output Voltage
Input Referred Noise Voltage vs Frequency
(VCC/VEE=±15V, TA=25°C, AV=40dB)
(VCC/VEE=±15V, RL=2kΩ, f=1kHz)
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
±0
±5
±10
±15
±20
SupplyVoltage [V]
Figure 20.
Input Referred Noise Voltage vs Supply Voltage
(TA=25°C, DIN-AUDIO)
(*)The above characteristics are measurements of typical sample, they are not guaranteed.
www.rohm.com
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
©2012 ROHM Co., Ltd. All rights reserved.
10/24
TSZ22111･15･001
Datasheet
LM4565xxx
Application Information
NULL method condition for Test Circuit 1
VCC, VEE, EK, VICM Unit:V
Calculation
Parameter
VF
S1
S2
S3
VCC VEE
EK
0
VICM
0
Input Offset Voltage
VF1
VF2
VF3
VF4
VF5
VF6
VF7
ON
ON OFF
15
-15
1
-10
10
Large Signal Voltage Gain
ON
ON
ON
ON
ON
15
-15
0
2
3
4
-10
10
Common Mode Rejection Ratio
(Input Common-mode Voltage Range)
ON OFF
ON OFF
15
-15
0
0
4
-4
Power Supply Rejection Ratio
0
18
-18
－ Calculation－
|VF1|
1+RF/RS
VIO
[V]
=
1. Input Offset Voltage (VIO)
∆EK × (1+RF/RS)
AV
[dB]
2. Large Signal Voltage Gain (AV)
= 20Log
|VF2-VF3|
3. Common-mode Rejection Ratio (CMRR)
4. Power Supply Rejection Ratio (PSRR)
∆VICM × (1+RF/RS)
CMRR
PSRR
20Log
[dB]
[dB]
=
|VF4 - VF5|
∆VCC × (1+ RF/RS)
= 20Log
|VF6 - VF7|
0.1µF
RF=50kΩ
500kΩ
0.1µF
SW1
VCC
EK
15V
RS=50Ω
RI=10kΩ
VO
500kΩ
0.1µF
0.1µF
DUT
VEE
NULL
-15V
SW3
RI=10kΩ
1000pF
RS=50Ω
50kΩ
VF
RL
VICM
VRL
Figure21. Test Circuit 1
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
11/24
Datasheet
LM4565xxx
Switch Condition for Test Circuit 2
SW No.
SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10 SW11 SW12
Supply Current
OFF OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF
OFF ON OFF OFF ON OFF OFF ON OFF OFF ON OFF
OFF OFF ON OFF OFF OFF ON OFF ON OFF OFF ON
ON OFF OFF ON ON OFF OFF OFF ON OFF OFF ON
Maximum Output Voltage RL=2kΩ
Slew Rate
Maximum Frequency
Input voltage
SW3
R2 100kΩ
SW4
●
VH
VCC=30V
－
＋
VL
SW1
SW2
t
SW8 SW9
SW10 SW11 SW12
Input wave
SW5
SW6
SW7
Output voltage
VH
R1
1kΩ
VEE
SR=ΔV/Δt
90%
RL
CL
VIN-
VIN+
VO
ΔV
10%
VL
Δt
Figure 22. Test Circuit2
t
Output wave
Figure 23. Slew Rate Input Output Wave
R2=100kΩ
R2=100kΩ
VCC
VCC
R1=1kΩ
R1=1kΩ
OUT1
OUT2
R1//R2
=1Vrms
R1//R2
VEE
VEE
VIN
100×OUT1
CS=20Log
OUT2
Figure 24. Test Circuit 3 (Channel Separation)
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
12/24
Datasheet
LM4565xxx
Application Example
○Voltage Follower
Voltage gain is 0dB.
Using this circuit, the output voltage (OUT) is controlled
to be equal to the input voltage (IN). This circuit also
stabilizes OUT due to high input impedance and low
output impedance. Computation for OUT is shown
below.
VCC
OUT
OUT=IN
IN
VEE
Figure 25. Voltage Follower
○Inverting Amplifier
R2
VCC
For inverting amplifier, IN is amplified by a voltage gain
decided by the ratio of R1 and R2.The out-of-phase
output voltage is shown in the next expression.
OUT=-(R2/R1)・IN
R1
IN
This circuit has input impedance equal to R1.
OUT
R1//R2
VEE
Figure 26. Inverting Amplifier Circuit
○Non-inverting amplifier
For non-inverting amplifier, IN is amplified by a voltage
gain decided by the ratio of R1 and R2. OUT is in-phase
with Vin and is shown in the next expression.
OUT=(1+R2/R1)・IN
Effectively, this circuit has high input impedance since its
input side is the same as that of the operational
amplifier.
R1
R2
VCC
VEE
OUT
IN
Figure 27. Non-inverting Amplifier Circuit
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
13/24
Datasheet
LM4565xxx
Power Dissipation
Power dissipation (total loss) indicates the power that the IC can consume at TA=25°C (normal temperature). As the IC
consumes power, it heats up, causing its temperature to be higher than the ambient temperature. The allowable
temperature that the IC can accept is limited. This depends on the circuit configuration, manufacturing process, and
consumable power.
Power dissipation is determined by the allowable temperature within the IC (maximum junction temperature) and the
thermal resistance of the package used (heat dissipation capability). Maximum junction temperature is typically equal to the
maximum storage temperature. The heat generated through the consumption of power by the IC radiates from the mold
resin or lead frame of the package. Thermal resistance, represented by the symbol θJA °C/W, indicates this heat dissipation
capability. Similarly, the temperature of an IC inside its package can be estimated by thermal resistance.
Figure 28(a) shows the model of the thermal resistance of the package. The equation below shows how to compute for the
Thermal resistance (θJA), given the ambient temperature (TA), maximum junction temperature (TJmax), and power dissipation
(PD).
θJA
=
(TJmax－TA) / PD °C/W
・・・・・ (Ⅰ)
The derating curve in Figure 28(b) indicates the power that the IC can consume with reference to ambient temperature.
Power consumption of the IC begins to attenuate at certain temperatures. This gradient is determined by Thermal
resistance (θJA), which depends on the chip size, power consumption, package, ambient temperature, package condition,
wind velocity, etc. This may also vary even when the same of package is used. Thermal reduction curve indicates a
reference value measured at a specified condition. Figure 28(c) shows an example of the derating curve for LM4565xxx.
[W]
Power dissipation of LSI
P
Dmax
θJA=(TJmax-TA)/ PD °C/W
P2
P1
θJA2<θJA1
T
A
Ambient temperature
[ °C ]
JA2
θ’
θ
JA2
TJ’max TJmax
θ’
1
JA1
θJ
A1
Chip surface temperature
[ °C ]
TJ
0
25
50
75
100
125
150
[ °C ]
T
Ambient temperature
A
(a) Thermal Resistance
(b) Derating Curve
1.0
0.8
0.6
0.4
0.2
LM4565F (Note 10)
LM4565FJ (Note11)
LM4565FV (Note 12)
LM4565FVT (Note 12)
LM4565FVM (Note 13)
LM4565FVJ (Note 13)
0.0
0
25
50
75
100
125
150
Ambient Temperature [°C]
(c) LM4565xxx
Unit
mW/°C
(Note 10) (Note 11) (Note 12) (Note 13)
5.5 5.4 5.0 4.7
When using the unit above TA=25°C, subtract the value above per °C. Permissible dissipation is the value
when FR4 glass epoxy board 70mm×70mm×1.6mm (copper foil area below 3%) is mounted
Figure 28. Thermal Resistance and Derating Curve
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
14/24
Datasheet
LM4565xxx
Operational Notes
1.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power
supply pins.
2.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3.
4.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5.
Thermal Consideration
Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. The absolute maximum rating of the PD stated in this specification is when
the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum
rating, increase the board size and copper area to prevent exceeding the PD rating.
6.
7.
Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately
obtained. The electrical characteristics are guaranteed under the conditions of each parameter.
Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush
current may flow instantaneously due to the internal powering sequence and delays, especially if the IC
has more than one power supply. Therefore, give special consideration to power coupling capacitance,
power wiring, width of ground wiring, and routing of connections.
8.
9.
Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may
subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply
should always be turned off completely before connecting or removing it from the test setup during the inspection
process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during
transport and storage.
10. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment)
and unintentional solder bridge deposited in between pins during assembly to name a few.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
15/24
Datasheet
LM4565xxx
Operational Notes – continued
11. Regarding the Input Pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a
parasitic diode or transistor. For example (refer to figure below):
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to
operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should
be avoided.
Figure 29. Example of hic IC structure
VCC
12. Unused Circuits
It is recommended to apply the connection (see Figure 30.) and set the
non-inverting input terminal at a potential within the Input Common-mode
Voltage Range (VICM) for any unused circuit.
Keep this potential
in VICM
VICM
13. Input Voltage
Applying VEE +36V to the input terminal is possible without causing
deterioration of the electrical characteristics or destruction, regardless of
the supply voltage. However, this does not ensure normal circuit operation.
Please note that the circuit operates normally only when the input voltage
is within the common mode input voltage range of the electric
characteristics.
VEE
Figure 30. Example of Application Circuit
for Unused Op-amp
14. Power Supply(single/dual)
The operational amplifier operates when the voltage supplied is between VCC and VEE. Therefore, the single supply
operational amplifier can be used as dual supply operational amplifier as well.
15. IC Handling
When pressure is applied to the IC through warp on the printed circuit board, the characteristics may fluctuate due to
the piezo effect. Be careful with the warp on the printed circuit board.
16. The IC Destruction Caused by Capacitive Load
The IC may be damaged when VCC terminal and VEE terminal is shorted with the charged output terminal capacitor.
When IC is used as an operational amplifier or as an application circuit where oscillation is not activated by an output
capacitor, output capacitor must be kept below 0.1μF in order to prevent the damage mentioned above.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
16/24
Datasheet
LM4565xxx
Physical Dimensions Tape and Reel Information
Package Name
SOP8
(Max 5.35 (include.BURR))
(UNIT : mm)
PKG : SOP8
Drawing No. : EX112-5001-1
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
17/24
Datasheet
LM4565xxx
Physical Dimension Tape and Reel Information - continued
Package Name
SOP-J8
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
18/24
Datasheet
LM4565xxx
Physical Dimension Tape and Reel Information - continued
Package Name
SSOP-B8
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
19/24
Datasheet
LM4565xxx
Physical Dimension Tape and Reel Information - continued
Package Name
TSSOP-B8
<Tape and Reel information>
Tape
Embossed carrier tape
3000pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
20/24
Datasheet
LM4565xxx
Physical Dimension Tape and Reel Information - continued
Package Name
MSOP8
<Tape and Reel information>
Tape
Embossed carrier tape
3000pcs
Quantity
TR
Direction
of feed
The direction is the 1pin of product is at the upper right when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1pin
Direction of feed
Order quantity needs to be multiple of the minimum quantity.
Reel
∗
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
21/24
Datasheet
LM4565xxx
Physical Dimension Tape and Reel Information - continued
Package Name
TSSOP-B8J
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
22/24
Datasheet
LM4565xxx
Marking Diagram
SOP8(TOP VIEW)
TSSOP-B8(TOP VIEW)
Part Number Marking
Part Number Marking
LOT Number
LOT Number
1PIN MARK
1PIN MARK
SOP-J8(TOP VIEW)
MSOP8(TOP VIEW)
Part Number Marking
LOT Number
Part Number Marking
LOT Number
1PIN MARK
1PIN MARK
TSSOP-B8J(TOP VIEW)
SSOP-B8(TOP VIEW)
Part Number Marking
LOT Number
Part Number Marking
LOT Number
1PIN MARK
1PIN MARK
Product Name
Package Type
Marking
F
SOP8
SOP-J8
4565
L4565
4565
FJ
FV
SSOP-B8
TSSOP-B8
MSOP8
LM4565
FVT
FVM
FVJ
L4565
L4565
L4565
TSSOP-B8J
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
23/24
Datasheet
LM4565xxx
Land Pattern Data
All dimensions in mm
Land pitch
e
Land space
MIE
Land length
Land width
b2
PKG
≥ℓ 2
SOP8
SOP-J8
1.27
1.27
0.65
0.65
0.65
0.65
4.60
3.90
4.60
4.60
2.62
3.20
1.10
0.76
0.76
0.35
0.35
0.35
0.35
1.35
1.20
1.20
0.99
1.15
SSOP-B8
TSSOP-B8
MSOP8
TSSOP-B8J
MIE
ℓ 2
Revision History
Date
Revision
Changes
30.Nov.2012
2.Sep.2013
15.Apr.2014
001
002
003
New Release
Added LM4565FV, LM4565FJ,LM4565FVT,LM4565FVM,LM4565FVJ
The Operating Supply Voltage Range is changed.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0RAR0G200590-1-2
15.Apr.2014 Rev.003
24/24
Daattaasshheeeett
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice – GE
Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice – GE
Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2014 ROHM Co., Ltd. All rights reserved.
Datasheet
Buy
LM4565F - Web Page
Distribution Inventory
Part Number
Package
LM4565F
SOP8
Unit Quantity
2500
Minimum Package Quantity
Packing Type
Constitution Materials List
RoHS
2500
Taping
inquiry
Yes
相关型号：
LM4565FVM
LM4565FVM是高电压增益、宽频带的低噪声运算放大器。等效输入噪声电压（5 HznV/ ）及总谐波失真（0.0002%）优异，因此是适用于音响设备、有源滤波器等用途的运算放大器。
ROHM
LM4565FVT
LM4565FVT是高电压增益、宽频带的低噪声运算放大器。等效输入噪声电压（5 HznV/ ）及总谐波失真（0.0002%）优异，因此是适用于音响设备、有源滤波器等用途的运算放大器。
ROHM
LM4576-3.3BT
Switching Regulator, Voltage-mode, 3.5A, 200kHz Switching Freq-Max, BICMOS, PSFM5, TO-220, 5 PIN
MICROCHIP
LM4576-3.3BT-LB02
Switching Regulator, Voltage-mode, 3.5A, 200kHz Switching Freq-Max, BICMOS, PSFM5
MICROCHIP
LM4576-3.3BU
Switching Regulator, Voltage-mode, 3.5A, 200kHz Switching Freq-Max, BICMOS, PSSO5
MICROCHIP
LM4576-3.3BU-TR
Switching Regulator, Voltage-mode, 3.5A, 200kHz Switching Freq-Max, BICMOS, PSSO5
MICROCHIP
LM4576-3.3BUT&R
Switching Regulator, Voltage-mode, 3.5A, 200kHz Switching Freq-Max, BICMOS, PSSO5
MICROCHIP
LM4576-5.0BT
Switching Regulator, Voltage-mode, 3.5A, 200kHz Switching Freq-Max, BICMOS, PSFM5
MICROCHIP
©2020 ICPDF网 联系我们和版权申明