CY7C63903-PVXC [ROCHESTER]
8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDSO28, 5.30 MM, SSOP-28;型号: | CY7C63903-PVXC |
厂家: | Rochester Electronics |
描述: | 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDSO28, 5.30 MM, SSOP-28 时钟 光电二极管 外围集成电路 |
文件: | 总69页 (文件大小:4140K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CY7C63310
CY7C638xx
CY7C639xx
enCoRe™ II
Low-Speed USB Peripheral Controller
— Each 3.3V pin supports high-impedance input,
internal pull-up, open drain output or traditional
1.0
Features
• enCoRe™ II USB—“enhanced Component Reduction”
CMOS output
— Crystalless oscillator with support for an external
crystal or resonator. The internal oscillator
eliminates the need for an external crystal or
resonator
• SPI serial communication
— Master or slave operation
—Configurable up to 2-Mbit/second transfers
—Supports half duplex single data line mode for
optical sensors
— Internal 3.3V regulator and internal USB pull-up
resistor
• 2-channel 8-bit or 1-channel 16-bit capture timer.
Capture timers registers store both rising and falling
edge times
— Configurable IO for real-world interface without
external components
• USB Specification Compliance
— Two registers each for two input pins
— Conforms to USB Specification, Version 2.0
— Conforms to USB HID Specification, Version 1.1
— Supports one Low-Speed USB device address
— Separate registers for rising and falling edge capture
— Simplifies interface to RF inputs for wireless
applications
—Supports one control endpoint and two data
endpoints
• Internal low-power wake-up timer during suspend
mode
— Periodic wake-up with no external components
• Programmable Interval Timer interrupts
— Integrated USB transceiver
• Enhanced 8-bit microcontroller
— Harvard architecture
• Reduced RF emissions at 27 MHz and 96 MHz
• Advanced development tools based on Cypress
MicroSystems PSoC™ tools
— M8C CPU speed can be up to 24 MHz or sourced by
an external crystal, resonator, or signal
• Watchdog timer (WDT)
• Internal memory
• Low-voltage detection with user-configurable
threshold voltages
• Improved output drivers to reduce EMI
• Operating voltage from 4.0V to 5.25VDC
• Operating temperature from 0–70°C
— Up to 256 bytes of RAM
—Up to eight Kbytes of Flash including EEROM
emulation
• Interface can auto-configure to operate as PS/2 or USB
—No externalcomponents forswitchingbetween PS/2
and USB modes
• Availablein16/18/24/40-pinPDIP, 16/18/24-pinSOIC, 24-
pin QSOP, 28/48-pin SSOP, and DIE form
— No GPIO pins needed to manage dual-mode
capability
• Industry standard programmer support
• Low power consumption
— Typically 10 mA at 6 MHz
— 10-µA sleep
• In-system re-programmability
— Allows easy firmware update
• General-purpose I/O ports
—Up to 36 General Purpose I/O (GPIO) pins
1.1
Applications
The CY7C633xx/CY7C638xx/CY7C639xx is targeted for the
following applications:
• PC HID devices
— Mice (optomechanical, optical, trackball)
— Keyboards
• Gaming
— Joysticks
— High current drive on GPIO pins. Configurable 8- or
50-mA/pin current sink on designated pins
— Game pads
— Each GPIO port supports high-impedance inputs,
configurable pull-up, open drain output, CMOS/TTL
inputs, and CMOS output
—Console keyboards
• General-purpose
— Barcode scanners
—POS terminal
— Maskable interrupts on all I/O pins
• 125-mA 3.3V voltage regulator can power external 3.3V
devices
• 3.3V I/O pins
— Consumer electronics
— Toys
—4 I/O pins with 3.3V logic levels
—Remote controls
Cypress Semiconductor Corporation
Document 38-08035 Rev. *F
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised November 28, 2005
CY7C63310
CY7C638xx
CY7C639xx
the same interrupt. There is no separate interrupt for each. The
Watchdog timer can be used to ensure the firmware never gets
stalled in an infinite loop.
2.0
Introduction
Cypress has reinvented its leadership position in the low-
speed USB market with a new family of innovative microcon-
trollers. Introducing enCoRe II USB — “enhanced Component
Reduction.” Cypress has leveraged its design expertise in
USB solutions to advance its family of low-speed USB micro-
controllers, which enable peripheral developers to design new
products with a minimum number of components. The
enCoRe II USB technology builds on to the enCoRe family.
The enCoRe family has an integrated oscillator that eliminates
the external crystal or resonator, reducing overall cost. Also
integrated into this chip are other external components
commonly found in low-speed USB applications such as pull-
up resistors, wake-up circuitry, and a 3.3V regulator.
The microcontroller supports 23 maskable interrupts in the
vectored interrupt controller. Interrupt sources include a USB
bus reset, LVR/POR, a programmable interval timer, a
1.024-ms output from the Free Running Timer, three USB
endpoints, two capture timers, five GPIO Ports, three GPIO
pins, two SPI, a 16-bit free running timer wrap, an internal
wake-up timer, and a bus active interrupt. The wake-up timer
causes periodic interrupts when enabled. The USB endpoints
interrupt after a USB transaction complete is on the bus. The
capture timers interrupt whenever a new timer value is saved
due to a selected GPIO edge event. A total of eight GPIO
interrupts support both TTL or CMOS thresholds. For
additional flexibility, on the edge sensitive GPIO pins, the
interrupt polarity is programmable to be either rising or falling.
All of this adds up to a lower system cost.
The enCoRe II is an 8-bit Flash-programmable microcontroller
with integrated low-speed USB interface. The instruction set
has been optimized specifically for USB and PS/2 operations,
although the microcontrollers can be used for a variety of other
embedded applications.
The free-running 16-bit timer provides two interrupt sources:
the programmable interval timer with 1-µs resolution and the
1.024-ms outputs. The timer can be used to measure the
duration of an event under firmware control by reading the
timer at the start and at the end of an event, then calculating
the difference between the two values. The two 8-bit capture
timers save a programmable 8-bit range of the free-running
timer when a GPIO edge occurs on the two capture pins (P0.5,
P0.6). The two 8-bit captures can be ganged into a single
16-bit capture.
The enCoRe II features up to 36 general-purpose I/O (GPIO)
pins to support USB, PS/2 and other applications. The I/O pins
are grouped into five ports (Port 0 to 4). The pins on Port 0 and
Port 1 may each be configured individually while the pins on
Ports 2, 3, and 4 may only be configured as a group. Each
GPIO port supports high-impedance inputs, configurable pull-
up, open drain output, CMOS/TTL inputs, and CMOS output
with up to five pins that support programmable drive strength
of up to 50-mA sink current. GPIO Port 1 features four pins that
interface at a voltage level of 3.3 volts. Additionally, each I/O
pin can be used to generate a GPIO interrupt to the microcon-
troller. Each GPIO port has its own GPIO interrupt vector with
the exception of GPIO Port 0. GPIO Port 0 has three dedicated
pins that have independent interrupt vectors (P0.2 - P0.4).
The enCoRe II includes an integrated USB serial interface
engine (SIE) that allows the chip to easily interface to a USB
host. The hardware supports one USB device address with
three endpoints.
The USB D+ and D– pins can optionally be used as PS/2
SCLK and SDATA signals so that products can be designed to
respond to either USB or PS/2 modes of operation. PS/2
operation is supported with internal 5-KΩ pull-up resistors on
P1.0 (D+) and P1.1 (D–) and an interrupt to signal the start of
PS/2 activity. In USB mode, the integrated 1.5-KΩ pull-up
resistor on D– can be controlled under firmware. No external
components are necessary for dual USB and PS/2 systems,
and no GPIO pins need to be dedicated to switching between
modes. Slow edge rates operate in both modes to reduce EMI.
The enCoRe II features an internal oscillator. With the
presence of USB traffic, the internal oscillator can be set to
precisely tune to USB timing requirements (24 MHz ±1.5%).
Optionally, an external 12-MHz or 24-MHz crystal can be used
to provide a higher precision reference for USB operation. The
clock generator provides the 12-MHz and 24-MHz clocks that
remain internal to the microcontroller.
The enCoRe II supports in-system programming by using the
D+ and D– pins as the serial programming mode interface.
The programming protocol is not USB.
The enCoRe II has up to eight Kbytes of Flash for user’s code
and up to 256 bytes of RAM for stack space and user
variables.
In addition, the enCoRe II includes a Watchdog timer, a
vectored interrupt controller, a 16-bit Free-Running Timer, and
Capture Timers. The Power-on reset circuit detects logic when
power is applied to the device, generates resets the logic to a
known state, and begins executing instructions at Flash
address 0x0000. When power falls below a programmable trip
voltage generates reset or may be configured to generate
interrupt. There is a Low-voltage detect circuit that detects
when VCC drops below a programmable trip voltage. It may be
configurable to generate an LVD interrupt to inform the
processor about the low-voltage event. POR and LVD share
3.0
Conventions
In this document, bit positions in the registers are shaded to
indicate which members of the enCoRe II family implement the
bits.
Available in all enCoRe II family members
CY7C639xx and CY7C638xx only
CY7C639xx only
Document 38-08035 Rev. *F
Page 2 of 68
CY7C63310
CY7C638xx
CY7C639xx
4.0
Logic Block Diagram
Low-Speed
USB/PS2
Wakeup
Timer
16 GPIO
Pins
Low-Speed
USB SIE
Interrupt
Control
16 Extended
I/O Pins
4 3VIO/SPI
Pins
3.3V
Transceiver
Regulator
and Pull-up
Internal
24 MHz
Oscillator
RAM
Up to 256
Byte
Flash
Up to 8K
Byte
Capture
Timers
M8C CPU
Clock
Control
12-bit Timer
Crystal
Oscillator
Watchdog
Timer
POR /
Low-Voltage
Detect
Figure 4-1. CY7C633xx/CY7C638xx/CY7C639xx Block Diagram
Document 38-08035 Rev. *F
Page 3 of 68
CY7C63310
CY7C638xx
CY7C639xx
5.0
Packages/Pinouts
Top View
CY7C63801
16-pin PDIP
CY7C63801
16-pin SOIC
CY7C63310
16-pin PDIP
CY7C63310
16-pin SOIC
CY7C63803
16-pin SOIC
P1.2
P1.6/SMISO
SSEL/P1.3
SCLK/P1.4
SMOSI/P1.5
SMISO/P1.6
P0.6/TIO1
16
15
14
13
12
11
10
9
P0.6/TIO1
P0.5/TIO0
P0.4/INT2
P0.3/INT1
P0.2/INT0
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
P1.6/SMISO
P0.6/TIO1
P0.5/TIO0
P0.4/INT2
P0.3/INT1
P0.2/INT0
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
V
P1.5/SMOSI
P1.4/SCLK
P1.3/SSEL
P1.2
P1.5/SMOSI
P1.4/SCLK
P1.3/SSEL
P1.2/VREG
CC
P1.1/D–
P1.0/D+
V
SS
P0.0
P0.1
P0.2/INT0
V
P0.5/TIO0
INT2/P0.4
INT1/P0.3
P0.1
P0.0
V
P0.1
P0.0
CC
CC
P1.1/D–
P1.0/D+
P1.1/D–
P1.0/D+
V
V
SS
SS
CY7C63823
24-pin PDIP
CY7C63813
18-pin PDIP
CY7C63813
18-pin SOIC
P1.3/SSEL
P1.2/VREG
P3.0
P3.1
SCLK/P1.4
SMOSI/P1.5
SMISO/P1.6
P1.7
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
P1.2/VREG
SSEL/P1.3
SCLK/P1.4
SMOSI/P1.5
SMISO/P1.6
P1.7
18
17
16
15
14
13
12
11
10
P1.7
1
2
3
4
5
6
7
8
9
P0.7
P0.6/TIO1
P0.5/TIO0
P0.4/INT2
P0.3/INT1
1
2
3
4
5
6
7
8
9
18
17
16
15
14
13
12
11
10
V
P1.6/SMISO
P1.5/SMOSI
P1.4/SCLK
P1.3/SSEL
CC
V
CC
P1.1/D–
P1.0/D+
P1.1/D–
P1.0/D+
V
SS
V
SS
P0.7
TIO1/P0.6
TIO0/P0.5
INT2/P0.4
P0.0
P0.1
P0.2/INT0
P0.3/INT1
P0.2/INT0
P0.1
P1.2/VREG
P2.0
P2.1
P0.0
P0.1
NC
NC
P0.7
V
CC
P0.0
P1.1/D–
P1.0/D+
16
15
14
13
V
9
SS
TIO1/P0.6
TIO0/P0.5
INT2/P0.4
10
11
12
P0.2/INT0
P0.3/INT1
CY7C63903
28-pin SSOP
CY7C63823
24-pin QSOP
CY7C63823
24-pin SOIC
V
V
P2.7
P2.6
P2.5
P2.4
1
2
3
4
5
6
7
8
28
27
26
25
24
23
22
21
20
19
SS
P1.7
NC
P0.7
CC
NC
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
16
15
NC
P0.7
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
P3.7
P3.6
P1.6/SMISO
P1.5/SMOSI
P1.7
P1.6/SMISO
TIO1/P0.6
TIO0/P0.5
INT2/P0.4
INT1/P0.3
INT0/P0.2
P0.1
TIO1/P0.6
TIO0/P0.5
INT2/P0.4
INT1/P0.3
INT0/P0.2
P0.1
P3.5
P3.4
P1.7
P1.6/SMISO
P1.5/SMOSI
P1.4/SCLK
P1.3/SSEL
P1.4/SCLK
P3.1
P3.0
P1.3/SSEL
P1.2/VREG
P1.5/SMOSI
P1.4/SCLK
P3.1
P3.0
P1.3/SSEL
P1.2/VREG
P0.7
TIO1/P0.6
TIO0/P0.5
INT2/P0.4
INT1/P0.3
INT0/P0.2
CLKOUT/P0.1
CLKIN/P0.0
9
V
16
15
14
13
P0.0
P2.1
P2.0
NC
9
P0.0
P2.1
P2.0
CC
9
10
11
12
P1.1/D–
P1.0/D+
V
10
11
12
10
11
12
CC
P1.2/VREG
18
17
14
13
P1.1/D–
P1.0/D+
V
CC
V
V
SS
SS
16
15
P1.1/D–
P1.0/D+
13
14
V
SS
Figure 5-1. Package Configurations
Document 38-08035 Rev. *F
Page 4 of 68
CY7C63310
CY7C638xx
CY7C639xx
Top View
CY7C63913
40-pin PDIP
CY7C63923
48-pin SSOP
CY7C63923-XC
DIE
NC
V
P4.1
P4.0
P2.7
P2.6
P2.5
P2.4
P2.3
P2.2
V
NC
NC
NC
NC
1
2
3
4
5
6
7
8
48
47
46
45
44
43
42
41
1
2
3
4
5
6
7
8
40
39
38
37
36
35
34
33
CC
SS
NC
NC
P4.3
P4.2
P3.7
P3.6
P3.5
P3.4
P4.0
P2.7
P2.6
P2.5
P2.4
P2.3
P2.2
7
8
NC
V
40
P3.6
9
39 P3.5
V
SS
10
CC
38 P3.4
11
12
13
P4.3
P4.2
P3.7
P3.6
P3.5
P3.4
P3.3
P3.2
P4.1
P4.0
P2.7
P2.6
P2.5
P2.4
P2.3
P2.2
P2.1
37 P3.3
36
35
P3.2
P3.1
P3.3
P3.2
32
31
30
29
40
39
38
37
9
9
P2.1
P2.0
P0.7
34
33
32
31
10
11
12
13
14
15
16
17
18
19
20
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
P3.1
P3.0
P3.0
P1.7
P1.6/SMISO
P1.5/SMOSI
14
15
16
17
P2.1
P2.0
P1.7
P0.6/TIO1
P0.5/TIO0
P0.4/INT2
P0.3/INT1
P0.2/INT0
P0.1/CLKOUT
P0.0/CLKIN
28
27
26
25
24
23
22
21
P1.6/SMISO
P1.5/SMOSI
P1.4/SCLK
P1.3/SSEL
P1.2/VREG
36
35
34
33
32
31
30
29
28
27
P0.7
30
P1.4/SCLK
P3.1
P3.0
P0.6/TIO1
29 P1.3/SSEL
28 P1.2/VREG
P0.5/TIO0 18
P2.0
P0.7
19
P0.4/INT2
P1.7
P1.6/SMISO
P1.5/SMOSI
P1.4/SCLK
P1.3/SSEL
P1.2/VREG
P0.3/INT1 20
P0.2/INT0 21
P0.6/TIO1
P0.5/TIO0
P0.4/INT2
P0.3/INT1
P0.2/INT0
P0.1/CLKOUT
P0.0/CLKIN
V
CC
27
V
P0.1/CLKOUT 22
P1.1/D–
P1.0/D+
CC
V
SS
V
CC
P1.1/D–
P1.0/D+
26
25
V
SS
Figure 5-1 Package Configurations (continued)
5.1
Pinouts Assignments
Table 5-1. Pin Assignments
24
QSOP
48
40
28
24
24
18
18
16
16
Die
SSOP PDIP SSOP
SOIC PDIP SIOC PDIP SOIC PDIP Pad
Name
Description
7
6
3
2
7
6
P4.0
P4.1
GPIO Port 4 – configured as a group
(nibble)
42
43
38
39
42 P4.2
43 P4.3
34
35
36
37
38
39
40
41
30
31
32
33
34
35
36
37
19
20
18
19
1
2
34 P3.0
35 P3.1
36 P3.2
37 P3.3
38 P3.4
39 P3.5
40 P3.6
41 P3.7
GPIO Port 3 – configured as a group
(byte)
24
25
26
27
15
14
13
12
11
10
9
11
10
9
11
10
11
10
18
17
15 P2.0
14 P2.1
13 P2.2
12 P2.3
11 P2.4
10 P2.5
GPIO Port 2 – configured as a group
(byte)
8
7
5
4
3
2
6
5
9
8
P2.6
P2.7
8
4
Document 38-08035 Rev. *F
Page 5 of 68
CY7C63310
CY7C638xx
CY7C639xx
Table 5-1. Pin Assignments (continued)
24
QSOP
48
40
28
24
24
18
18
16
16
Die
SSOP PDIP SSOP
SOIC PDIP SIOC PDIP SOIC PDIP Pad
Name
Description
[1]
[1]
25
26
28
21
22
24
15
16
18
14
15
17
13
14
16
20 10
21 11
15
16
18
9
13
25 P1.0/D+
GPIO Port 1 bit 0 / USB D+
GPIO Port 1 bit 1 / USB D–
10 14
12 16
26 P1.1/D–
23 13
28 P1.2/VREG
GPIO Port 1 bit 2—Configured individually.
3.3V if regulator is enabled. (The 3.3V
regulator is not available in the
CY7C63310 and CY7C63801.)
29
30
31
32
25
26
27
28
19
20
21
22
18
21
22
23
17
20
21
22
24 14
1
2
3
4
13
14
15
16
1
2
3
4
29 P1.3/SSEL
30 P1.4/SCLK
GPIO Port 1 bit 3—Configured individually.
Alternate function is SSEL signal of the
SPI bus TTL voltage thresholds
3
4
5
15
16
17
GPIO Port 1 bit 4—Configured individually.
Alternate function is SCLK signal of the
SPI bus TTL voltage thresholds
31 P1.5/SMOSI GPIO Port 1 bit 5—Configured individually.
Alternate function is SMOSI signal of the
SPI bus TTL voltage thresholds
32 P1.6/SMISO GPIO Port 1 bit 6—Configured individually.
Alternate function is SMISO signal of the
SPI bus TTL voltage thresholds
33
23
29
19
23
13
24
9
23
9
6
18
8
5
33 P1.7
GPIO Port 1 bit 7—Configured individually.
TTL voltage threshold.
16
13
7
6
11
10
23 P0.0/CLKIN
GPIO Port 0 bit 0—Configured individually.
On CY7C639xx, optional Clock In when
external crystal oscillator is disabled or
crystal input when external crystal oscil-
lator is enabled.
On CY7C638xx and CY7C63310, oscil-
lator input when configured as Clock In
22
18
12
8
8
15
7
12
22 P0.1 /
CLKOUT
GPIO Port 0 bit 1—Configured individually
On CY7C639xx, optional clock out when
external crystal oscillator is disabled or
crystal output drive when external crystal
oscillator is enabled.
On CY7C638xx and CY7C63310, oscil-
lator output when configured as Clock out.
21
20
19
18
17
16
15
14
11
10
9
7
6
5
4
7
6
5
4
14
13
12
11
6
5
4
3
11
10
9
5
4
3
2
9
8
7
6
21 P0.2/INT0
20 P0.3/INT1
19 P0.4/INT2
18 P0.5/TIO0
GPIO port 0 bit 2—Configured individually
Optional rising edge interrupt INT0
GPIO port 0 bit 3—Configured individually
Optional rising edge interrupt INT1
GPIO port 0 bit 4—Configured individually
Optional rising edge interrupt INT2
8
8
GPIO port 0 bit 5—Configured individually
Alternate function Timer capture inputs or
Timer output TIO0
17
16
13
12
7
6
3
3
10
2
1
7
6
1
5
17 P0.6/TIO1
16 P0.7
GPIO port 0 bit 6—Configured individually
Alternate function Timer capture inputs or
Timer output TIO1
2
1
2
1
9
7
GPIO port 0 bit 7—Configured individually
Not in 16 pin PDIP or SOIC package
1,2,3,
4
1,2, NC
3,4
No connect
Note:
1. P1.0(D+) and P1.1(D–) pins should be in I/O mode when used as GPIO and in I mode.
SB
Document 38-08035 Rev. *F
Page 6 of 68
CY7C63310
CY7C638xx
CY7C639xx
Table 5-1. Pin Assignments (continued)
24
QSOP
48
40
28
24
24
18
18
16
16
Die
SSOP PDIP SSOP
SOIC PDIP SIOC PDIP SOIC PDIP Pad
Name
Description
45,46,
47,48
12
24
8
45, NC
46,
47,
No connect
48
5
1
5
V
V
Power
CC
SS
27
44
24
23
40
20
1
16
–
15
–
22 12
17
14
11
8
15
12
27
44
24
–
–
9
Ground
28
13
12
19
The Accumulator Register (CPU_A) is the general-purpose
register that holds the results of instructions that specify any
of the source addressing modes.
6.0
CPU Architecture
This family of microcontrollers is based on a high performance,
8-bit, Harvard-architecture microprocessor. Five registers
control the primary operation of the CPU core. These registers
are affected by various instructions, but are not directly acces-
sible through the register space by the user.
The Index Register (CPU_X) holds an offset value that is used
in the indexed addressing modes. Typically, this is used to
address a block of data within the data memory space.
The Stack Pointer Register (CPU_SP) holds the address of the
current top-of-stack in the data memory space. It is affected by
the PUSH, POP, LCALL, CALL, RETI, and RET instructions,
which manage the software stack. It can also be affected by
the SWAP and ADD instructions.
Table 6-1. CPU Registers and Register Names
Register
Register Name
CPU_F
Flags
Program Counter
Accumulator
Stack Pointer
Index
CPU_PC
CPU_A
The Flag Register (CPU_F) has three status bits: Zero Flag bit
[1]; Carry Flag bit [2]; Supervisory State bit [3]. The Global
Interrupt Enable bit [0] is used to globally enable or disable
interrupts. The user cannot manipulate the Supervisory State
status bit [3]. The flags are affected by arithmetic, logic, and
shift operations. The manner in which each flag is changed is
dependent upon the instruction being executed (i.e., AND,
OR, XOR). See Table 8-1.
CPU_SP
CPU_X
The 16-bit Program Counter Register (CPU_PC) allows for
direct addressing of the full eight Kbytes of program memory
space.
Document 38-08035 Rev. *F
Page 7 of 68
CY7C63310
CY7C638xx
CY7C639xx
7.0
7.1
CPU Registers
Flags Register
The Flags Register can only be set or reset with logical
instruction.
Table 7-1. CPU Flags Register (CPU_F) [R/W]
Bit #
Field
7
6
5
4
XIO
R/W
0
3
Super
R
2
Carry
RW
0
1
0
Global IE
RW
Reserved
Zero
RW
1
Read/Write
Default
–
0
–
0
–
0
0
0
Bit [7:5]: Reserved
Bit 4: XIO
Set by the user to select between the register banks
0 = Bank 0
1 = Bank 1
Bit 3: Super
Indicates whether the CPU is executing user code or Supervisor Code. (This code cannot be accessed directly by the user)
0 = User Code
1 = Supervisor Code
Bit 2: Carry
Set by CPU to indicate whether there has been a carry in the previous logical/arithmetic operation
0 = No Carry
1 = Carry
Bit 1: Zero
Set by CPU to indicate whether there has been a zero result in the previous logical/arithmetic operation
0 = Not Equal to Zero
1 = Equal to Zero
Bit 0: Global IE
Determines whether all interrupts are enabled or disabled
0 = Disabled
1 = Enabled
Note: CPU_F register is only readable with explicit register address 0xF7. The OR F, expr and AND F, expr instructions must
be used to set and clear the CPU_F bits
7.1.1
Accumulator Register
Table 7-2. CPU Accumulator Register (CPU_A)
Bit #
Field
7
6
5
4
3
2
1
0
CPU Accumulator [7:0]
Read/Write
Default
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
Bit [7:0]: CPU Accumulator [7:0]
8-bit data value holds the result of any logical/arithmetic instruction that uses a source addressing mode
7.1.2
Index Register
Table 7-3. CPU X Register (CPU_X)
Bit #
Field
7
6
5
4
3
2
1
0
X [7:0]
Read/Write
Default
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
Bit [7:0]: X [7:0]
8-bit data value holds an index for any instruction that uses an indexed addressing mode
Document 38-08035 Rev. *F
Page 8 of 68
CY7C63310
CY7C638xx
CY7C639xx
7.1.3
Stack Pointer Register
Table 7-4. CPU Stack Pointer Register (CPU_SP)
Bit #
Field
7
6
5
4
3
2
1
0
Stack Pointer [7:0]
Read/Write
Default
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
Bit [7:0]: Stack Pointer [7:0]
8-bit data value holds a pointer to the current top-of-stack
7.1.4
CPU Program Counter High Register
Table 7-5. CPU Program Counter High Register (CPU_PCH)
Bit #
Field
7
6
5
4
3
2
1
0
Program Counter [15:8]
Read/Write
Default
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
Bit [7:0]: Program Counter [15:8]
8-bit data value holds the higher byte of the program counter
7.1.5
CPU Program Counter Low Register
Table 7-6. CPU Program Counter Low Register (CPU_PCL)
Bit #
Field
7
6
5
4
3
2
1
0
Program Counter [7:0]
Read/Write
Default
–
0
–
0
–
0
–
0
–
0
–
0
–
0
–
0
Bit [7:0]: Program Counter [7:0]
8-bit data value holds the lower byte of the program counter
Examples
7.2
Addressing Modes
ADD
A,
7
;In this case, the immediate value
;of 7 is added with the Accumulator,
;and the result is placed in the
;Accumulator.
7.2.1
Source Immediate
The result of an instruction using this addressing mode is
placed in the A register, the F register, the SP register, or the
X register, which is specified as part of the instruction opcode.
Operand 1 is an immediate value that serves as a source for
the instruction. Arithmetic instructions require two sources.
Instructions using this addressing mode are two bytes in
length.
MOV
AND
X,
F,
8
9
;In this case, the immediate value
;of 8 is moved to the X register.
;In this case, the immediate value
;of 9 is logically ANDed with the F
;register and the result is placed
;in the F register.
Table 7-7. Source Immediate
Opcode
Instruction
Operand 1
Immediate Value
7.2.2
Source Direct
The result of an instruction using this addressing mode is
placed in either the A register or the X register, which is
specified as part of the instruction opcode. Operand 1 is an
address that points to a location in either the RAM memory
space or the register space that is the source for the
instruction. Arithmetic instructions require two sources; the
second source is the A register or X register specified in the
opcode. Instructions using this addressing mode are two bytes
in length.
Document 38-08035 Rev. *F
Page 9 of 68
CY7C63310
CY7C638xx
CY7C639xx
Examples
Table 7-8. Source Direct
Opcode
ADD
[7],
A
A
;In this case, the value in
;the memory location at
Operand 1
Instruction
Source Address
;address 7 is added with the
;Accumulator, and the result
;is placed in the memory
;location at address 7. The
;Accumulator is unchanged.
Examples
ADD
A,
[7]
;In this case, the ;value in
;the RAM memory location at
;address 7 is added with the
;Accumulator, and the result
;is placed in the Accumulator.
MOV
REG[8],
;In this case, the Accumula-
;tor is moved to the regis-
;ter space location at
;address 8. The Accumulator
;is unchanged.
MOV
X,
REG[8] ;In this case, the value in
;the register space at address
;8 is moved to the X register.
7.2.5
Destination Indexed
7.2.3
Source Indexed
The result of an instruction using this addressing mode is
placed within either the RAM memory space or the register
space. Operand 1 is added to the X register forming the
address that points to the location of the result. The source for
the instruction is the A register. Arithmetic instructions require
two sources; the second source is the location specified by
Operand 1 added with the X register. Instructions using this
addressing mode are two bytes in length.
The result of an instruction using this addressing mode is
placed in either the A register or the X register, which is
specified as part of the instruction opcode. Operand 1 is added
to the X register forming an address that points to a location in
either the RAM memory space or the register space that is the
source for the instruction. Arithmetic instructions require two
sources; the second source is the A register or X register
specified in the opcode. Instructions using this addressing
mode are two bytes in length.
Table 7-11. Destination Indexed
Opcode
Instruction
Operand 1
Destination Index
Table 7-9. Source Indexed
Opcode
Instruction
Operand 1
Source Index
Example
ADD [X+7],
A
;In this case, the value in the
;memory location at address X+7
;is added with the Accumulator,
;and the result is placed in
;the memory location at address
;x+7. The Accumulator is
;unchanged.
Examples
ADD
A,
[X+7]
;In this case, the value in
;the memory location at
;address X + 7 is added with
;the Accumulator, and the
;result is placed in the
;Accumulator.
7.2.6
Destination Direct Immediate
MOV
X,
REG[X+8]
;In this case, the value in
;the register space at
;address X + 8 is moved to
;the X register.
The result of an instruction using this addressing mode is
placed within either the RAM memory space or the register
space. Operand 1 is the address of the result. The source for
the instruction is Operand 2, which is an immediate value.
Arithmetic instructions require two sources; the second source
is the location specified by Operand 1. Instructions using this
addressing mode are three bytes in length.
7.2.4
Destination Direct
The result of an instruction using this addressing mode is
placed within either the RAM memory space or the register
space. Operand 1 is an address that points to the location of
the result. The source for the instruction is either the A register
or the X register, which is specified as part of the instruction
opcode. Arithmetic instructions require two sources; the
second source is the location specified by Operand 1. Instruc-
tions using this addressing mode are two bytes in length.
Table 7-12. Destination Direct Immediate
Opcode
Operand 1
Operand 2
Instruction
Destination Address
Immediate Value
Table 7-10. Destination Direct
Opcode
Instruction
Operand 1
Destination Address
Document 38-08035 Rev. *F
Page 10 of 68
CY7C63310
CY7C638xx
CY7C639xx
Examples
Example
MOV
[7], [8] ;In this case, the value in the
;memory location at address 8 is
;moved to the memory location at
;address 7.
ADD [7],
5
6
;In this case, value in the mem-
;ory location at address 7 is
;added to the immediate value of
;5, and the result is placed in
;the memory location at address 7.
7.2.9
Source Indirect Post Increment
MOV REG[8],
;In this case, the immediate
;value of 6 is moved into the
;register space location at
;address 8.
The result of an instruction using this addressing mode is
placed in the Accumulator. Operand 1 is an address pointing
to a location within the memory space, which contains an
address (the indirect address) for the source of the instruction.
The indirect address is incremented as part of the instruction
execution. This addressing mode is only valid on the MVI
instruction. The instruction using this addressing mode is two
bytes in length. Refer to the PSoC Designer: Assembly
Language User Guide for further details on MVI instruction.
7.2.7
Destination Indexed Immediate
The result of an instruction using this addressing mode is
placed within either the RAM memory space or the register
space. Operand 1 is added to the X register to form the
address of the result. The source for the instruction is Operand
2, which is an immediate value. Arithmetic instructions require
two sources; the second source is the location specified by
Operand 1 added with the X register. Instructions using this
addressing mode are three bytes in length.
Table 7-15. Source Indirect Post Increment
Opcode
Instruction
Operand 1
Source Address Address
Table 7-13. Destination Indexed Immediate
Example
Opcode
Operand 1
Operand 2
MVI
A,
[8] ;In this case, the value in the
;memory location at address 8 is
;an indirect address. The memory
;location pointed to by the indi-
;rect address is moved into the
;Accumulator. The indirect
Instruction
Destination Index
Immediate Value
Examples
ADD
[X+7],
5
6
;In this case, the value in
;the memory location at
;address X+7 is added with
;the immediate value of 5,
;and the result is placed
;in the memory location at
;address X+7.
;address is then incremented.
7.2.10 Destination Indirect Post Increment
The result of an instruction using this addressing mode is
placed within the memory space. Operand 1 is an address
pointing to a location within the memory space, which contains
an address (the indirect address) for the destination of the
instruction. The indirect address is incremented as part of the
instruction execution. The source for the instruction is the
Accumulator. This addressing mode is only valid on the MVI
instruction. The instruction using this addressing mode is two
bytes in length.
MOV
REG[X+8],
;In this case, the immedi-
;ate value of 6 is moved
;into the location in the
;register space at
;address X+8.
7.2.8
Destination Direct
Table 7-16. Destination Indirect Post Increment
The result of an instruction using this addressing mode is
placed within the RAM memory. Operand 1 is the address of
the result. Operand 2 is an address that points to a location in
the RAM memory that is the source for the instruction. This
addressing mode is only valid on the MOV instruction. The
instruction using this addressing mode is three bytes in length.
Opcode
Instruction
Operand 1
Destination Address Address
Example
MVI
[8],
A
;In this case, the value in
;the memory location at
Table 7-14. Destination Direct
;address 8 is an indirect
;address. The Accumulator is
;moved into the memory loca-
;tion pointed to by the indi-
;rect address. The indirect
;address is then incremented.
Opcode
Operand 1
Operand 2
Instruction
Destination Address
Source Address
Document 38-08035 Rev. *F
Page 11 of 68
CY7C63310
CY7C638xx
CY7C639xx
needed, the Instruction Set Summary tables are described in
detail in the PSoC Designer Assembly Language User Guide
(available on the www.cypress.com web site).
8.0
Instruction Set Summary
The instruction set is summarized in Table 8-1 by numerically
and serves as a quick reference. If more information is
[2, 3]
Table 8-1. Instruction Set Summary Sorted Numerically by Opcode Order
Instruction Format
1 SSC
Flags
Instruction Format
2 OR [X+expr], A
3 OR [expr], expr
3 OR [X+expr], expr
1 HALT
Flags
Instruction Format
2 MOV [expr], X
1 MOV A, X
1 MOV X, A
2 MOV A, reg[expr]
2 MOV A, reg[X+expr]
3 MOV [expr], [expr]
2 MOV reg[expr], A
2 MOV reg[X+expr], A
3 MOV reg[expr], expr
3 MOV reg[X+expr], expr
1 ASL A
Flags
00 15
2D
2E
8
9
Z
Z
Z
5A
5B
5C
5D
5E
5
4
4
6
7
01
02
03
04
05
06
4
6
7
7
8
9
2 ADD A, expr
C, Z
Z
2 ADD A, [expr]
2 ADD A, [X+expr]
2 ADD [expr], A
2 ADD [X+expr], A
3 ADD [expr], expr
3 ADD [X+expr], expr
1 PUSH A
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
2F 10
30
31
32
33
34
35
36
9
4
6
7
7
8
9
Z
Z
2 XOR A, expr
Z
Z
Z
Z
Z
Z
Z
2 XOR A, [expr]
5F 10
2 XOR A, [X+expr]
2 XOR [expr], A
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
5
6
8
9
4
7
8
4
7
8
4
7
8
4
7
8
4
4
4
4
4
4
7
8
4
4
7
8
07 10
08
09
4
4
6
7
7
8
9
2 XOR [X+expr], A
3 XOR [expr], expr
3 XOR [X+expr], expr
2 ADD SP, expr
2 ADC A, expr
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
0A
0B
0C
0D
0E
2 ADC A, [expr]
2 ADC A, [X+expr]
2 ADC [expr], A
2 ADC [X+expr], A
3 ADC [expr], expr
3 ADC [X+expr], expr
1 PUSH X
37 10
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
Z
38
39
5
5
7
8
8
9
2 ASL [expr]
2 ASL [X+expr]
1 ASR A
2 CMP A, expr
3A
3B
3C
3D
2 CMP A, [expr]
if (A=B) Z=1
if (A<B) C=1
2 CMP A, [X+expr]
3 CMP [expr], expr
3 CMP [X+expr], expr
2 MVI A, [ [expr]++ ]
2 MVI [ [expr]++ ], A
1 NOP
2 ASR [expr]
2 ASR [X+expr]
1 RLC A
0F 10
10
11
12
13
14
15
16
4
4
6
7
7
8
9
2 SUB A, expr
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
Z
3E 10
3F 10
Z
2 RLC [expr]
2 RLC [X+expr]
1 RRC A
2 SUB A, [expr]
2 SUB A, [X+expr]
2 SUB [expr], A
2 SUB [X+expr], A
3 SUB [expr], expr
3 SUB [X+expr], expr
1 POP A
40
41
4
9
3 AND reg[expr], expr
3 AND reg[X+expr], expr
3 OR reg[expr], expr
3 OR reg[X+expr], expr
3 XOR reg[expr], expr
3 XOR reg[X+expr], expr
3 TST [expr], expr
3 TST [X+expr], expr
3 TST reg[expr], expr
3 TST reg[X+expr], expr
1 SWAP A, X
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
2 RRC [expr]
2 RRC [X+expr]
2 AND F, expr
2 OR F, expr
2 XOR F, expr
1 CPL A
42 10
43
44 10
45
46 10
9
17 10
18
19
5
4
6
7
7
8
9
9
2 SBB A, expr
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
1A
1B
1C
1D
1E
2 SBB A, [expr]
2 SBB A, [X+expr]
2 SBB [expr], A
2 SBB [X+expr], A
3 SBB [expr], expr
3 SBB [X+expr], expr
1 POP X
47
48
49
8
9
9
1 INC A
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
C, Z
1 INC X
2 INC [expr]
2 INC [X+expr]
1 DEC A
4A 10
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5
7
7
5
4
4
5
6
5
6
8
9
4
6
7
1F 10
2 SWAP A, [expr]
2 SWAP X, [expr]
1 SWAP A, SP
1 DEC X
20
21
22
23
24
25
26
5
4
6
7
7
8
9
2 DEC [expr]
2 DEC [X+expr]
3 LCALL
2 AND A, expr
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
2 AND A, [expr]
2 AND A, [X+expr]
2 AND [expr], A
2 AND [X+expr], A
3 AND [expr], expr
3 AND [X+expr], expr
1 ROMX
1 MOV X, SP
7C 13
7D
7E 10
2 MOV A, expr
Z
Z
Z
7
3 LJMP
2 MOV A, [expr]
1 RETI
C, Z
2 MOV A, [X+expr]
2 MOV [expr], A
7F
8x
8
5
1 RET
2 JMP
27 10
28 11
2 MOV [X+expr], A
3 MOV [expr], expr
3 MOV [X+expr], expr
2 MOV X, expr
9x 11
2 CALL
Ax
Bx
Cx
Dx
Ex
5
5
5
5
7
2 JZ
29
2A
2B
2C
4
6
7
7
2 OR A, expr
2 JNZ
2 OR A, [expr]
2 JC
2 OR A, [X+expr]
2 OR [expr], A
2 MOV X, [expr]
2 JNC
2 MOV X, [X+expr]
2 JACC
Fx 13
2 INDEX
Z
Notes:
2. Interrupt routines take 13 cycles before execution resumes at interrupt vector table.
3. The number of cycles required by an instruction is increased by one for instructions that span 256-byte boundaries in the Flash memory space.
Document 38-08035 Rev. *F
Page 12 of 68
CY7C63310
CY7C638xx
CY7C639xx
9.0
9.1
Memory Organization
Flash Program Memory Organization
after reset
Address
16-bit PC
0x0000
0x0004
0x0008
0x000C
0x0010
0x0014
0x0018
0x001C
0x0020
0x0024
0x0028
0x002C
0x0030
0x0034
0x0038
0x003C
0x0040
0x0044
0x0048
0x004C
0x0050
0x0054
0x0058
0x005C
0x0060
0x0064
0x0068
Program execution begins here after a reset
POR/LVD
INT0
SPI Transmitter Empty
SPI Receiver Full
GPIO Port 0
GPIO Port 1
INT1
EP0
EP1
EP2
USB Reset
USB Active
1 ms Interval timer
Programmable Interval Timer
Timer Capture 0
Timer Capture 1
16 Bit Free Running Timer Wrap
INT2
PS2 Data Low
GPIO Port 2
GPIO Port 3
GPIO Port 4
Reserved
Reserved
Sleep Timer
Program Memory begins here (if below interrupts not used,
program memory can start lower)
0x0BFF
0x0FFF
3-KB ends here (CY7C63310)
4-KB ends here (CY7C63801)
0x1FFF
8-KB ends here (CY7C639xx and CY7C638x3)
Figure 9-1. Program Memory Space with Interrupt Vector Table
Document 38-08035 Rev. *F
Page 13 of 68
CY7C63310
CY7C638xx
CY7C639xx
9.2
Data Memory Organization
The CY7C633xx/638xx/639xx microcontrollers provide up to
256 bytes of data RAM. In normal usage, the SRAM is parti-
tioned into two areas: stack, and user variables:
after reset
8-bit PSP
Address
0x00
Stack begins here and grows upward (user can modify)
The user determines the amount of memory needed for Stack
User Variables
Top of RAM Memory
0xFF
Figure 9-2. Data Memory Organization
enCoRe II part to enter serial programming mode and then to
9.3
Flash
use the test queue to issue Flash access functions in the
This section describes the Flash block of the enCoRe II. Much
of the user-visible Flash functionality including programming
and security are implemented in the M8C Supervisory Read
Only Memory (SROM).
SROM.
9.4
SROM
The SROM holds code that is used to boot the part, calibrate
circuitry, and perform Flash operations. (Table 9-1 lists the
SROM functions.) The functions of the SROM may be
accessed in normal user code or operating from Flash. The
SROM exists in a separate memory space from user code.
The SROM functions are accessed by executing the Super-
visory System Call instruction (SSC), which has an opcode of
00h. Prior to executing the SSC the M8C’s accumulator needs
to be loaded with the desired SROM function code from
Table 9-1. Undefined functions will cause a HALT if called from
user code. The SROM functions are executing code with calls;
therefore, the functions require stack space. With the
exception of Reset, all of the SROM functions have a
parameter block in SRAM that must be configured before
executing the SSC. Table 9-2 lists all possible parameter block
variables. The meaning of each parameter, with regards to a
specific SROM function, is described later in this chapter.
9.3.1
Flash Programming and Security
All Flash programming is performed by code in the SROM. The
registers that control the Flash programming are only visible
to the M8C CPU when it is executing out of SROM. This makes
it impossible to read, write or erase the Flash by bypassing the
security mechanisms implemented in the SROM.
Customer firmware can only program the Flash via SROM
calls. The data or code images can be sourced via any
interface with the appropriate support firmware. This type of
programming requires a ‘boot-loader’—a piece of firmware
resident on the Flash. For safety reasons this boot-loader
should not be overwritten during firmware rewrites.
The Flash provides four extra auxiliary rows that are used to
hold Flash block protection flags, boot time calibration values,
configuration tables, and any device values. The routines for
accessing these auxiliary rows are documented in the SROM
section. The auxiliary rows are not affected by the device
erase function.
Table 9-1. SROM Function Codes
Function Code
Function Name
SWBootReset
ReadBlock
WriteBlock
EraseBlock
EraseAll
Stack Space
00h
01h
02h
03h
05h
06h
07h
0
7
9.3.2
In-System Programming
Most designs that include an enCoRe II part will have a USB
connector attached to the USB D+/D– pins on the device.
These designs require the ability to program or reprogram a
part through these two pins alone. The programming protocol
is not USB.
10
9
11
3
TableRead
CheckSum
enCoRe II devices enable this type of in-system programming
by using the D+ and D– pins as the serial programming mode
interface. This allows an external controller to cause the
3
Document 38-08035 Rev. *F
Page 14 of 68
CY7C63310
CY7C638xx
CY7C639xx
Two important variables that are used for all functions are
KEY1 and KEY2. These variables are used to help discrim-
inate between valid SSCs and inadvertent SSCs. KEY1 must
always have a value of 3Ah, while KEY2 must have the same
value as the stack pointer when the SROM function begins
execution. This would be the Stack Pointer value when the
SSC opcode is executed, plus three. If either of the keys do
not match the expected values, the M8C will halt (with the
exception of the SWBootReset function). The following code
puts the correct value in KEY1 and KEY2. The code starts with
a halt, to force the program to jump directly into the setup code
and not run into it.
are erased, a second loop erases and then programs each
protection block with zeros.
9.5
SROM Function Descriptions
9.5.1
SWBootReset Function
The SROM function, SWBootReset, is the function that is
responsible for transitioning the device from a reset state to
running user code. The SWBootReset function is executed
whenever the SROM is entered with an M8C accumulator
value of 00h: the SRAM parameter block is not used as an
input to the function. This will happen, by design, after a
hardware reset, because the M8C's accumulator is reset to
00h or when user code executes the SSC instruction with an
accumulator value of 00h. The SWBootReset function will not
execute when the SSC instruction is executed with a bad key
value and a non-zero function code. An enCoRe II device will
execute the HALT instruction if a bad value is given for either
KEY1 or KEY2.
halt
SSCOP: mov [KEY1], 3ah
mov X, SP
mov A, X
add A, 3
mov [KEY2], A
The SWBootReset function verifies the integrity of the
calibration data by way of a 16-bit checksum, before releasing
the M8C to run user code.
Table 9-2. SROM Function Parameters
Variable Name
SRAM Address
0,F8h
Key1 / Counter / Return Code
9.5.2
ReadBlock Function
Key2 / TMP
BlockID
Pointer
Clock
0,F9h
The ReadBlock function is used to read 64 contiguous bytes
from Flash: a block.
0,FAh
0,FBh
The first thing this function does is to check the protection bits
and determine if the desired BLOCKID is readable. If read
protection is turned on, the ReadBlock function will exit setting
the accumulator and KEY2 back to 00h. KEY1 will have a
value of 01h, indicating a read failure. If read protection is not
enabled, the function will read 64 bytes from the Flash using
a ROMX instruction and store the results in SRAM using an
MVI instruction. The first of the 64 bytes will be stored in SRAM
at the address indicated by the value of the POINTER
parameter. When the ReadBlock completes successfully the
accumulator, KEY1 and KEY2 will all have a value of 00h.
0,FCh
Mode
0,FDh
Delay
0,FEh
PCL
0,FFh
The SROM also features Return Codes and Lockouts.
9.4.1 Return Codes
Return codes aid in the determination of success or failure of
a particular function. The return code is stored in KEY1’s
position in the parameter block. The CheckSum and
TableRead functions do not have return codes because
KEY1’s position in the parameter block is used to return other
data.
Table 9-4. ReadBlock Parameters
Name
KEY1
Address
0,F8h
Description
3Ah
KEY2
0,F9h
Stack Pointer value, when SSC is
executed.
Table 9-3. SROM Return Codes
BLOCKID
POINTER
0,FAh
Flash block number
Return Code
Description
0,FBh First of 64 addresses in SRAM
where returned data should be
stored
00h
01h
Success
Function not allowed due to level of protection
on block.
9.5.3
WriteBlock Function
02h
03h
Software reset without hardware reset.
Fatal error, SROM halted.
The WriteBlock function is used to store data in the Flash. Data
is moved 64 bytes at a time from SRAM to Flash using this
function. The first thing the WriteBlock function does is to
check the protection bits and determine if the desired
BLOCKID is writable. If write protection is turned on, the Write-
Block function will exit setting the accumulator and KEY2 back
to 00h. KEY1 will have a value of 01h, indicating a write failure.
The configuration of the WriteBlock function is straightforward.
The BLOCKID of the Flash block, where the data is stored,
must be determined and stored at SRAM address FAh.
Read, write, and erase operations may fail if the target block
is read or write protected. Block protection levels are set
during device programming.
The EraseAll function overwrites data in addition to leaving the
entire user Flash in the erase state. The EraseAll function
loops through the number of Flash macros in the product,
executing the following sequence: erase, bulk program all
zeros, erase. After all the user space in all the Flash macros
Document 38-08035 Rev. *F
Page 15 of 68
CY7C63310
CY7C638xx
CY7C639xx
The SRAM address of the first of the 64 bytes to be stored in
Flash must be indicated using the POINTER variable in the
parameter block (SRAM address FBh). Finally, the CLOCK
and DELAY value must be set correctly. The CLOCK value
determines the length of the write pulse that will be used to
store the data in the Flash. The CLOCK and DELAY values are
dependent on the CPU speed and must be set correctly. Refer
to “Clocking” Section for additional information.
Internal reading is always permitted by way of the ROMX
instruction. The ability to read by way of the SROM ReadBlock
function is indicated by SR. The protection level is stored in
two bits according to Table 9-7. These bits are bit packed into
the 64 bytes of the protection block. Therefore, each protection
block byte stores the protection level for four Flash blocks. The
bits are packed into a byte, with the lowest numbered block’s
protection level stored in the lowest numbered bits Table 9-7.
The first address of the protection block contains the
protection level for blocks 0 through 3; the second address is
for blocks 4 through 7. The 64th byte will store the protection
level for blocks 252 through 255.
Table 9-5. WriteBlock Parameters
Name
KEY1
Address
Description
0,F8h 3Ah
KEY2
0,F9h Stack Pointer value, when SSC is
executed.
Table 9-7. Protection Modes
Mode
Settings
Description
Marketing
Unprotected
BLOCKID
0,FAh 8KB Flash block number (00h–7Fh)
4KB Flash block number (00h–3Fh)
3KB Flash block number (00h–2Fh)
00b SR ER EW IW Unprotected
01b SR ER EW IW Read protect
Factory upgrade
POINTER
0,FBh Firstof64addressesinSRAM, where
the data to be stored in Flash is
10b SR ER EW IW Disable external Field upgrade
write
located prior to calling WriteBlock.
11b SR ER EW IW Disable internal Full protection
write
CLOCK
DELAY
0,FCh Clock divider used to set the write
pulse width.
0,FEh For a CPU speed of 12 MHz set to 56h
7
6
5
4
3
2
1
0
Block n+3
Block n+2
Block n+1
Block n
9.5.4
EraseBlock Function
The EraseBlock function is used to erase a block of 64
contiguous bytes in Flash. The first thing the EraseBlock
function does is to check the protection bits and determine if
the desired BLOCKID is writable. If write protection is turned
on, the EraseBlock function will exit setting the accumulator
and KEY2 back to 00h. KEY1 will have a value of 01h,
indicating a write failure. The EraseBlock function is only
useful as the first step in programming. Erasing a block will not
cause data in a block to be one hundred percent unreadable.
If the objective is to obliterate data in a block, the best method
is to perform an EraseBlock followed by a WriteBlock of all
zeros.
The level of protection is only decreased by an EraseAll, which
places zeros in all locations of the protection block. To set the
level of protection, the ProtectBlock function is used. This
function takes data from SRAM, starting at address 80h, and
ORs it with the current values in the protection block. The
result of the OR operation is then stored in the protection
block. The EraseBlock function does not change the
protection level for a block. Because the SRAM location for the
protection data is fixed and there is only one protection block
per Flash macro, the ProtectBlock function expects very few
variables in the parameter block to be set prior to calling the
function. The parameter block values that must be set, besides
the keys, are the CLOCK and DELAY values.
To set up the parameter block for the EraseBlock function,
correct key values must be stored in KEY1 and KEY2. The
block number to be erased must be stored in the BLOCKID
variable and the CLOCK and DELAY values must be set based
on the current CPU speed.
Table 9-8. ProtectBlock Parameters
Name
KEY1
KEY2
Address
0,F8h
Description
3Ah
Table 9-6. EraseBlock Parameters
0,F9h
Stack Pointer value when SSC is
executed.
Name
KEY1
KEY2
Address
0,F8h
Description
CLOCK 0,FCh
DELAY 0,FEh
Clock divider used to set the write
pulse width.
3Ah
0,F9h
Stack Pointer value, when SSC is
executed.
For a CPU speed of 12 MHz set to 56h
BLOCKID 0,FAh
Flash block number (00h–7Fh)
9.5.6
EraseAll Function
CLOCK
0,FCh
Clock divider used to set the erase
pulse width.
The EraseAll function performs a series of steps that destroy
the user data in the Flash macros and resets the protection
block in each Flash macro to all zeros (the unprotected state).
The EraseAll function does not affect the three hidden blocks
above the protection block, in each Flash macro. The first of
these four hidden blocks is used to store the protection table
for its eight Kbytes of user data.
DELAY
0,FEh
For a CPU speed of 12 MHz set to
56h
9.5.5
ProtectBlock Function
The enCoRe II devices offer Flash protection on a block-by-
block basis. Table 9-7 lists the protection modes available. In
the table, ER and EW are used to indicate the ability to perform
external reads and writes. For internal writes, IW is used.
The EraseAll function begins by erasing the user space of the
Flash macro with the highest address range. A bulk program
of all zeros is then performed on the same Flash macro, to
Document 38-08035 Rev. *F
Page 16 of 68
CY7C63310
CY7C638xx
CY7C639xx
destroy all traces of the previous contents. The bulk program
is followed by a second erase that leaves the Flash macro in
a state ready for writing. The erase, program, erase sequence
is then performed on the next lowest Flash macro in the
address space if it exists. Following the erase of the user
space, the protection block for the Flash macro with the
highest address range is erased. Following the erase of the
protection block, zeros are written into every bit of the
protection table. The next lowest Flash macro in the address
space then has its protection block erased and filled with
zeros.
always be set to FFh when trim values are read. The BLOCKID
value, in the parameter block, is used to indicate which table
should be returned to the user. Only the three least significant
bits of the BLOCKID parameter are used by TableRead
function for the CY7C638xx and CY7C639xx. The upper five
bits are ignored. When the function is called, it transfers bytes
from the table to SRAM addresses F8h–FFh.
The M8C’s A and X registers are used by the TableRead
function to return the die’s Revision ID. The Revision ID is a
16-bit value hard coded into the SROM that uniquely identifies
the die’s design.
The end result of the EraseAll function is that all user data in
the Flash is destroyed and the Flash is left in an unpro-
grammed state, ready to accept one of the various write
commands. The protection bits for all user data are also reset
to the zero state
9.5.8
Checksum Function
The Checksum function calculates a 16-bit checksum over a
user specifiable number of blocks, within a single Flash macro
(Bank) starting from block zero. The BLOCKID parameter is
used to pass in the number of blocks to calculate the
checksum over. A BLOCKID value of 1 will calculate the
checksum of only block 0, while a BLOCKID value of 0 will
calculate the checksum of all 256 user blocks. The 16-bit
checksum is returned in KEY1 and KEY2. The parameter
KEY1 holds the lower eight bits of the checksum and the
parameter KEY2 holds the upper eight bits of the checksum.
The parameter block values that must be set, besides the
keys, are the CLOCK and DELAY values.
Table 9-9. EraseAll Parameters
Name Address
Description
KEY1
KEY2
0,F8h
0,F9h
3Ah
Stack Pointer value when SSC is
executed.
The checksum algorithm executes the following sequence of
three instructions over the number of blocks times 64 to be
checksummed.
CLOCK 0,FCh
DELAY 0,FEh
Clock divider used to set the write pulse
width.
romx
For a CPU speed of 12 MHz set to 56h
add [KEY1], A
adc [KEY2], 0
9.5.7
TableRead Function
The TableRead function gives the user access to part-specific
data stored in the Flash during manufacturing. It also returns
a Revision ID for the die (not to be confused with the Silicon
ID).
Table 9-11. Checksum Parameters
Name
KEY1
KEY2
Address
0,F8h
Description
3Ah
0,F9h
Stack Pointer value when SSC is
executed.
Table 9-10. Table Read Parameters
Name
KEY1
KEY2
Address
0,F8h
Description
BLOCKID 0,FAh
Number of Flash blocks to calculate
checksum on.
3Ah
0,F9h
Stack Pointer value when SSC is
executed.
10.0
Clocking
BLOCKID 0,FAh
Table number to read.
The enCoRe II internal oscillator outputs two frequencies, the
Internal 24-MHz Oscillator and the 32-KHz Low-power Oscil-
lator.
The table space for the enCoRe II is simply a 64-byte row
broken up into eight tables of eight bytes. The tables are
numbered zero through seven. All user and hidden blocks in
the CY7C638xx and CY7C639xx parts consist of 64 bytes.
The Internal 24-MHz Oscillator is designed such that it may be
trimmed to an output frequency of 24 MHz over temperature
and voltage variation. With the presence of USB traffic, the
Internal 24-MHz Oscillator can be set to precisely tune to USB
timing requirements (24 MHz ± 1.5%). Without USB traffic, the
Internal 24-MHz Oscillator accuracy is 24 MHz ± 5% (between
0°–70°C). No external components are required to achieve
this level of accuracy.
An internal table holds the Silicon ID and returns the Revision
ID. The Silicon ID is returned in SRAM, while the Revision ID
is returned in the CPU_A and CPU_X registers. The Silicon ID
is a value placed in the table by programming the Flash and is
controlled by Cypress Semiconductor Product Engineering.
The Revision ID is hard coded into the SROM. The Revision
ID is discussed in more detail later in this section.
The internal low-speed oscillator of nominally 32 KHz provides
a slow clock source for the enCoRe II in suspend mode, partic-
ularly to generate a periodic wake-up interrupt and also to
provide a clock to sequential logic during power-up and power-
down events when the main clock is stopped. In addition, this
oscillator can also be used as a clocking source for the Interval
Timer clock (ITMRCLK) and Capture Timer clock (TCAPCLK).
The 32-KHz Low-power Oscillator can operate in low-power
mode or can provide a more accurate clock in normal mode.
An internal table holds alternate trim values for the device and
returns a one-byte internal revision counter. The internal
revision counter starts out with a value of zero and is incre-
mented each time one of the other revision numbers is not
incremented. It is reset to zero each time one of the other
revision numbers is incremented. The internal revision count
is returned in the CPU_A register. The CPU_X register will
Document 38-08035 Rev. *F
Page 17 of 68
CY7C63310
CY7C638xx
CY7C639xx
The Internal 32-KHz Low-power Oscillator accuracy ranges
from –85% to +120% (between 0°–70° C).
the external crystal oscillator. An optional divide by two allows
the use of 24-MHz source.
For applications that require a higher clock accuracy, the
CY7C639xx part can optionally be sourced from an external
crystal oscillator. When operating in USB mode, the supplied
crystal oscillator must be either 12 MHz or 24 MHz in order for
the USB blocks to function properly. In non-USB mode, the
external oscillator can be up to 24 MHz.
The Interval Timer clock (ITMRCLK), can be sourced from the
external crystal oscillator, the Internal 24-MHz Oscillator, the
Internal 32-KHz Low-power Oscillator, or from the timer
capture clock (TCAPCLK). A programmable prescaler of 1, 2,
3, 4 then divides the selected source.
The Timer Capture clock (TCAPCLK) can be sourced from the
external crystal oscillator, Internal 24-MHz Oscillator, or the
Internal 32-KHz Low-power Oscillator.
10.1
Clock Architecture Description
The enCoRe II clock selection circuitry allows the selection of
independent clocks for the CPU, USB, Interval Timers and
Capture Timers.
When it is not being used by the external crystal oscillator, the
CLKOUT pin can be driven from one of many sources. This is
used for test and can also be used in some applications. The
sources that can drive the CLKOUT are:
On the CY7C639xx, the external oscillator can be sourced by
the crystal oscillator or when the crystal oscillator is disabled it
is sourced directly from the CLKIN pin. The external crystal
oscillator is fed through the EFTB block, which can optionally
be bypassed.
• CLKIN after the optional EFTB filter
• Internal 24-MHz Oscillator
• Internal 32-KHz Low-power Oscillator
• CPUCLK after the programmable divider
The CPU clock, CPUCLK, can be sourced from the external
crystal oscillator or the Internal 24-MHz Oscillator. The
selected clock source can optionally be divided by 2n where n
is 0-5,7 (see Table 10-5).
10.1.1 Clock Control Registers
10.1.2 Internal Clock Trim
USBCLK, which must be 12 MHz for the USB SIE to function
properly, can be sourced by the Internal 24-MHz Oscillator or
Table 10-1. IOSC Trim (IOSCTR) [0x34] [R/W]
Bit #
Field
7
6
foffset[2:0]
R/W
5
4
3
2
Gain[4:0]
R/W
1
0
Read/Write
Default
R/W
0
R/W
0
R/W
D
R/W
D
R/W
D
R/W
D
0
D
The IOSC Calibrate register is used to calibrate the internal oscillator. The reset value is undefined but during boot the SROM
writes a calibration value that is determined during manufacturing test. This value should not require change during normal use.
This is the meaning of ‘D’ in the Default field
Bit [7:5]: foffset [2:0]
This value is used to trim the frequency of the internal oscillator. These bits are not used in factory calibration and will be zero.
Setting each of these bits causes the appropriate fine offset in oscillator frequency.
foffset bit 0 = 7.5 KHz
foffset bit 1 = 15 KHz
foffset bit 2 = 30 KHz
Bit [4:0]: Gain [4:0]
The effective frequency change of the offset input is controlled through the gain input. A lower value of the gain setting increases
the gain of the offset input. This value sets the size of each offset step for the internal oscillator. Nominal gain change
(KHz/offsetStep) at each bit, typical conditions (24 MHz operation):
Gain bit 0 = –1.5 KHz
Gain bit 1 = –3.0 KHz
Gain bit 2 = –6 KHz
Gain bit 3 = –12 KHz
Gain bit 4 = –24 KHz
Document 38-08035 Rev. *F
Page 18 of 68
CY7C63310
CY7C638xx
CY7C639xx
10.1.3 External Clock Trim
Table 10-2. XOSC Trim (XOSCTR) [0x35] [R/W]
0
Mode
R/W
D
Bit #
Field
7
6
5
4
3
2
1
Reserved
XOSC XGM [2:0]
Reserved
Read/Write
Default
–
0
–
0
–
0
R/W
D
R/W
D
R/W
D
–
0
This register is used to calibrate the external crystal oscillator. The reset value is undefined but during boot the SROM writes a
calibration value that is determined during manufacturing test. This is the meaning of ‘D’ in the Default field
Bit [7:5]: Reserved
Bit [4:2]: XOSC XGM [2:0]
Amplifier transconductance setting. The Xgm settings are recommended for resonators with frequencies of interest for the
enCoRe II as below
Resonator
XGM Setting
Worst Case R (Ohms)
6-MHz Crystal
12-MHz Crystal
24-MHz Crystal
6-MHz Ceramic
001
011
111
001
403
201
101
70.4
41
12-MHz Ceramic 011
Bit 1: Reserved
Bit 0: Mode
0 = Oscillator Mode
1 = Fixed Maximum Bias test Mode
10.1.4 LPOSC Trim
Table 10-3. LPOSC Trim (LPOSCTR) [0x36] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
32-KHz Low
Power
Reserved
32-KHz Bias Trim [1:0]
32-KHz Freq Trim [3:0]
Read/Write
Default
R/W
D
–
R/W
D
R/W
D
R/W
D
R/W
D
R/W
D
R/W
D
D
This register is used to calibrate the 32-KHz Low-speed Oscillator. The reset value is undefined but during boot the SROM writes
a calibration value that is determined during manufacturing test. This value should not require change during normal use. This
is the meaning of ‘D’ in the Default field. If the 32-KHz Low-power bit needs to be written, care should be taken not to disturb
the 32-KHz Bias Trim and the 32-KHz Freq Trim fields from their factory calibrated values
Bit 7: 32-KHz Low Power
0 = The 32-KHz Low-speed Oscillator operates in normal mode
1 = The 32-KHz Low-speed Oscillator operates in a low-power mode. The oscillator continues to function normally but with
reduced accuracy
Bit 6: Reserved
Bit [5:4]: 32-KHz Bias Trim [1:0]
These bits control the bias current of the low-power oscillator.
0 0 = Mid bias
0 1 = High bias
1 0 = Reserved
1 1 = Disable (off)
Important Note: Do not program the 32-KHz Bias Trim [1:0] field with the reserved 10b value as the oscillator does not oscillate
at all corner conditions with this setting
Bit [3:0]: 32-KHz Freq Trim [3:0]
These bits are used to trim the frequency of the low-power oscillator
Document 38-08035 Rev. *F
Page 19 of 68
CY7C63310
CY7C638xx
CY7C639xx
10.1.5 CPU/USB Clock Configuration
Table 10-4. CPU/USB Clock Config CPUCLKCR) [0x30] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Reserved
USB CLK /2
Disable
USB CLK Select
Reserved
CPUCLK Select
Read/Write
Default
–
0
R/W
0
R/W
0
–
0
–
0
–
0
–
0
R/W
0
Bit 7: Reserved
Bit 6: USB CLK/2 Disable
This bit only affects the USBCLK when the source is the external crystal oscillator. When the USBCLK source is the Internal
24-MHz Oscillator, the divide by two is always enabled
0 = USBCLK source is divided by two. This is the correct setting to use when the Internal 24-MHz Oscillator is used, or when
the external source is used with a 24-MHz clock
1 = USBCLK is undivided. Use this setting only with a 12-MHz external clock
Bit 5: USB CLK Select
This bit controls the clock source for the USB SIE
0 = Internal 24-MHz Oscillator. With the presence of USB traffic, the Internal 24-MHz Oscillator can be trimmed to meet the USB
requirement of 1.5% tolerance (see Table 10-6)
1 = External clock—external oscillator on CLKIN and CLKOUT if the external oscillator is enabled (the XOSC Enable bit set in
the CLKIOCR Register—Table 10-8), or the CLKIN input if the external oscillator is disabled. Internal Oscillator is not trimmed
to USB traffic. Proper USB SIE operation requires a 12-MHz or 24-MHz clock accurate to <1.5%.
Bit [4:1]: Reserved
Bit 0: CPU CLK Select
0 = Internal 24-MHz Oscillator.
1 = External crystal oscillator—External crystal oscillator on CLKIN and CLKOUT if the external crystal oscillator is enabled,
CLKIN input if the external crystal oscillator is disabled
Note: the CPU speed selection is configured using the OSC_CR0 Register (Table 10-5)
Document 38-08035 Rev. *F
Page 20 of 68
CY7C63310
CY7C638xx
CY7C639xx
10.1.6 OSC_CR0 Clock Configuration
Table 10-5. OSC Control 0 (OSC_CR0) [0x1E0] [R/W]
Bit #
Field
7
6
5
No Buzz
R/W
0
4
3
2
1
0
Reserved
Sleep Timer [1:0]
CPU Speed [2:0]
Read/Write
Default
–
0
–
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:6]: Reserved
Bit 5: No Buzz
During sleep (the Sleep bit is set in the CPU_SCR Register—Table 11-1), the LVD and POR detection circuit is turned on
periodically to detect any POR and LVD events on the V pin (the Sleep Duty Cycle bits in the ECO_TR are used to control
CC
the duty cycle—Table 13-3). To facilitate the detection of POR and LVD events, the No Buzz bit is used to force the LVD and
POR detection circuit to be continuously enabled during sleep. This results in a faster response to an LVD or POR event during
sleep at the expense of a slightly higher than average sleep current
0 = The LVD and POR detection circuit is turned on periodically as configured in the Sleep Duty Cycle
1 = The Sleep Duty Cycle value is overridden. The LVD and POR detection circuit is always enabled
Note: The periodic Sleep Duty Cycle enabling is independent with the sleep interval shown in the Sleep [1:0] bits below
Bit [4:3]: Sleep Timer [1:0]
Sleep Timer Sleep Timer Clock
Sleep Period Watchdog Period
[1:0]
Frequency (Nominal) (Nominal) (Nominal)
00
512 Hz
64 Hz
8 Hz
1.95 ms
15.6 ms
125 ms
1 sec
6 ms
01
47 ms
375 ms
3 sec
10
11
1 Hz
Note: Sleep intervals are approximate
Bit [2:0]: CPU Speed [2:0]
The enCoRe II may operate over a range of CPU clock speeds. The reset value for the CPU Speed bits is zero; therefore, the
default CPU speed is one-eighth of the internal 24 MHz, or 3 MHz
Regardless of the CPU Speed bit’s setting, if the actual CPU speed is greater than 12 MHz, the 24-MHz operating requirements
apply. An example of this scenario is a device that is configured to use an external clock, which is supplying a frequency of 20
MHz. If the CPU speed register’s value is 0b011, the CPU clock will be 20 MHz. Therefore the supply voltage requirements for
the device are the same as if the part was operating at 24 MHz. The operating voltage requirements are not relaxed until the
CPU speed is at 12 MHz or less
CPU Speed CPU when Internal
[2:0]
000
001
010
011
100
101
110
111
Oscillator is selected External Clock
3 MHz (Default)
6 MHz
Clock In / 8
Clock In / 4
Clock In / 2
Clock In / 1
Clock In / 16
Clock In / 32
Clock In / 128
Reserved
12 MHz
24 MHz
1.5 MHz
750 KHz
187 KHz
Reserved
Important Note: Correct USB operations require the CPU clock speed to be at least eight times greater than the USB clock. If
the two clocks have the same source then the CPU clock divider should not be set to divide by more than 8. If the two clocks
have different sources, care must be taken to ensure that the maximum ratio of USB Clock/CPU Clock can never exceed 8
across the full specification range of both clock sources
Document 38-08035 Rev. *F
Page 21 of 68
CY7C63310
CY7C638xx
CY7C639xx
10.1.7 USB Oscillator Lock Configuration
Table 10-6. USB Osclock Clock Configuration (OSCLCKCR) [0x39] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Reserved
Fine Tune Only
USB Osclock
Disable
Read/Write
Default
–
0
–
0
–
0
–
0
–
0
–
0
R/W
0
R/W
0
This register is used to trim the Internal 24-MHz Oscillator using received low-speed USB packets as a timing reference. The
USB Osclock circuit is active when the Internal 24-MHz Oscillator provides the USB clock
Bit [7:2]: Reserved
Bit 1: Fine Tune Only
0 = Enable
1 = Disable the oscillator lock from performing the course-tune portion of its retuning. The oscillator lock must be allowed to
perform a course tuning in order to tune the oscillator for correct USB SIE operation. After the oscillator is properly tuned this bit
can be set to reduce variance in the internal oscillator frequency that would be caused course tuning
Bit 0: USB Osclock Disable
0 = Enable. With the presence of USB traffic, the Internal 24-MHz Oscillator precisely tunes to 24 MHz ± 1.5%
1 = Disable. The Internal 24-MHz Oscillator is not trimmed based on USB packets. This setting is useful when the internal
oscillator is not sourcing the USBSIE clock
10.1.8 Timer Clock Configuration
Table 10-7. Timer Clock Config (TMRCLKCR) [0x31] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
TCAPCLK Divider
TCAPCLK Select
ITMRCLK Divider
ITMRCLK Select
Read/Write
Default
R/W
1
R/W
0
R/W
0
R/W
0
R/W
1
R/W
1
R/W
1
R/W
1
Bit [7:6]: TCAPCLK Divider [1:0]
TCAPCLK Divider controls the TCAPCLK divisor
0 0 = Divider Value 2
0 1 = Divider Value 4
1 0 = Divider Value 6
1 1 = Divider Value 8
Bit [5:4]: TCAPCLK Select
The TCAPCLK Select field controls the source of the TCAPCLK
0 0 = Internal 24-MHz Oscillator
0 1 = External crystal oscillator—external crystal oscillator on CLKIN and CLKOUT if the external crystal oscillator is enabled,
CLKIN input if the external crystal oscillator is disabled (the XOSC Enable bit of the CLKIOCR Register is cleared—Table 10-8)
1 0 = Internal 32-KHz Low-power Oscillator
1 1 = TCAPCLK Disabled
Note: The 1024-µs interval timer is based on the assumption that TCAPCLK is running at 4 MHz. Changes in TCAPCLK
frequency will cause a corresponding change in the 1024-µs interval timer frequency
Bit [3:2]: ITMRCLK Divider
ITMRCLK Divider controls the ITMRCLK divisor.
0 0 = Divider value of 1
0 1 = Divider value of 2
1 0 = Divider value of 3
1 1 = Divider value of 4
Bit [1:0]: ITMRCLK Select
0 0 = Internal 24-MHz Oscillator
0 1 = External crystal oscillator – external crystal oscillator on CLKIN and CLKOUT if the external crystal oscillator is enabled,
CLKIN input if the external crystal oscillator is disabled
1 0 = Internal 32-KHz Low-power Oscillator
1 1 = TCAPCLK
Document 38-08035 Rev. *F
Page 22 of 68
CY7C63310
CY7C638xx
CY7C639xx
10.1.9 Clock In / Clock Out Configuration
Table 10-8. Clock I/O Config (CLKIOCR) [0x32] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Reserved
XOSC
Select
XOSC
Enable
EFTB
Disabled
CLKOUT Select
Read/Write
Default
–
0
–
0
–
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:5]: Reserved
Bit 4: XOSC Select
This bit when set, selects the external crystal oscillator clock as clock source of external clock. Care needs to be taken while
selecting the crystal oscillator clock. First enable the crystal oscillator and wait for few cycles, which is oscillator stabilization
period. Then select the crystal clock as clock source. Similarly, while deselect crystal clock, first deselect crystal clock as clock
source then disable the crystal oscillator.
0 = Not select external crystal oscillator clock
1 = Select the external crystal oscillator clock
Bit 3: XOSC Enable
This bit when set enables the external crystal oscillator. The external crystal oscillator shares pads CLKIN and CLKOUT with
two GPIOs—P0.0 and P0.1, respectively. When the external crystal oscillator is enabled, the CLKIN signal comes from the
external crystal oscillator block and the output enables on the GPIOs for P0.0 and P0.1 are disabled, eliminating the possibility
of contention. When the external crystal oscillator is disabled the source for CLKIN signal comes from the P0.0 GPIO input.
0 = Disable the external oscillator
1 = Enable the external oscillator
Note: The external crystal oscillator startup time takes up to 2 ms.
Bit 2: EFTB Disabled
This bit is only available on the CY7C639xx
0 = Enable the EFTB filter
1 = Disable the EFTB filter, causing CLKIN to bypass the EFTB filter
Bit [1:0]: CLKOUT Select
0 0 = Internal 24-MHz Oscillator
0 1 = External crystal oscillator – external crystal oscillator on CLKIN and CLKOUT if the external crystal oscillator is enabled,
CLKIN input if the external oscillator is disabled
1 0 = Internal 32-KHz Low-power Oscillator
1 1 = CPUCLK
10.2
CPU Clock During Sleep Mode
11.0
Reset
When the CPU enters sleep mode the CPUCLK Select (Bit 1,
Table 10-4) is forced to the Internal Oscillator, and the oscil-
lator is stopped. When the CPU comes out of sleep mode it is
running on the internal oscillator. The internal oscillator
recovery time is three clock cycles of the Internal 32-KHz Low-
power Oscillator.
The microcontroller supports two types of resets: Power-on
Reset (POR) and Watchdog Reset (WDR). When reset is
initiated, all registers are restored to their default states and all
interrupts are disabled.
The occurrence of a reset is recorded in the System Status and
Control Register (CPU_SCR). Bits within this register record
the occurrence of POR and WDR Reset respectively. The
firmware can interrogate these bits to determine the cause of
a reset.
If the system requires the CPU to run off the external clock
after awaking from sleep mode, firmware will need to switch
the clock source for the CPU. If the external clock source is the
external oscillator and the oscillator is disabled, firmware will
need to enable the external oscillator, wait for it to stabilize,
and then change the clock source.
The microcontroller resumes execution from Flash address
0x0000 after a reset. The internal clocking mode is active after
a reset, until changed by user firmware.
Note: The CPU clock defaults to 3 MHz (Internal 24-MHz
Oscillator divide-by-8 mode) at POR to guarantee operation at
the low V that might be present during the supply ramp.
CC
Document 38-08035 Rev. *F
Page 23 of 68
CY7C63310
CY7C638xx
CY7C639xx
Table 11-1. System Status and Control Register (CPU_SCR) [0xFF] [R/W]
Bit #
Field
7
GIES
R
6
5
4
3
Sleep
R/W
0
2
1
0
Reserved
WDRS
PORS
Reserved
Stop
R/W
0
[4]
[4]
Read/Write
Default
–
0
R/C
R/C
–
0
–
0
0
0
1
The bits of the CPU_SCR register are used to convey status and control of events for various functions of an enCoRe II device
Bit 7: GIES
The Global Interrupt Enable Status bit is a read only status bit and its use is discouraged. The GIES bit is a legacy bit, which
was used to provide the ability to read the GIE bit of the CPU_F register. However, the CPU_F register is now readable. When
this bit is set, it indicates that the GIE bit in the CPU_F register is also set which, in turn, indicates that the microprocessor will
service interrupts
0 = Global interrupts disabled
1 = Global interrupt enabled
Bit 6: Reserved
Bit 5: WDRS
The WDRS bit is set by the CPU to indicate that a WDR event has occurred. The user can read this bit to determine the type of
reset that has occurred. The user can clear but not set this bit
0 = No WDR
1 = A WDR event has occurred
Bit 4: PORS
The PORS bit is set by the CPU to indicate that a POR event has occurred. The user can read this bit to determine the type of
reset that has occurred. The user can clear but not set this bit
0 = No POR
1 = A POR event has occurred. (Note that WDR events will not occur until this bit is cleared)
Bit 3: SLEEP
Set by the user to enable CPU sleep state. CPU will remain in sleep mode until any interrupt is pending. The Sleep bit is covered
in more detail in the Sleep Mode section
0 = Normal operation
1 = Sleep
Bit [2:1]: Reserved
Bit 0: STOP
This bit is set by the user to halt the CPU. The CPU will remain halted until a reset (WDR, POR, or external reset) has taken
place. If an application wants to stop code execution until a reset, the preferred method would be to use the HALT instruction
rather than writing to this bit
0 = Normal CPU operation
1 = CPU is halted (not recommended)
cleared, the WDT cannot be disabled. The only exception to
this is if a POR event takes place, which will disable the WDT.
11.1
Power-on Reset
POR occurs every time the power to the device is switched on.
POR is released when the supply is typically 2.6V for the
upward supply transition, with typically 50 mV of hysteresis
during the power-on transient. Bit 4 of the System Status and
Control Register (CPU_SCR) is set to record this event (the
register contents are set to 00010000 by the POR). After a
POR, the microprocessor is held off for approximately 20 ms
The sleep timer is used to generate the sleep time period and
the Watchdog time period. The sleep timer uses the Internal
32-KHz Low-power Oscillator system clock to produce the
sleep time period. The user can program the sleep time period
using the Sleep Timer bits of the OSC_CR0 Register
(Table 10-5). When the sleep time elapses (sleep timer
overflows), an interrupt to the Sleep Timer Interrupt Vector will
be generated.
for the V
supply to stabilize before executing the first
CC
instruction at address 0x00 in the Flash. If the V
voltage
CC
drops below the POR downward supply trip point, POR is
The Watchdog Timer period is automatically set to be three
counts of the Sleep Timer overflows. This represents between
two and three sleep intervals depending on the count in the
Sleep Timer at the previous WDT clear. When this timer
reaches three, a WDR is generated.
reasserted. The V supply needs to ramp linearly from 0 to
CC
4V in 0 to 200 ms.
Important: The PORS status bit is set at POR and can only
be cleared by the user. It cannot be set by firmware.
The user can either clear the WDT, or the WDT and the Sleep
Timer. Whenever the user writes to the Reset WDT Register
(RES_WDT), the WDT will be cleared. If the data that is written
is the hex value 0x38, the Sleep Timer will also be cleared at
the same time.
11.2
Watchdog Timer Reset
The user has the option to enable the WDT. The WDT is
enabled by clearing the PORS bit. Once the PORS bit is
Note:
4. C = Clear. This bit can only be cleared by the user and cannot be set by firmware.
Document 38-08035 Rev. *F
Page 24 of 68
CY7C63310
CY7C638xx
CY7C639xx
Table 11-2. Reset Watchdog Timer (RESWDT) [0xE3] [W]
Bit #
Field
7
6
5
4
3
2
1
0
Reset Watchdog Timer [7:0]
Read/Write
Default
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
Any write to this register will clear Watchdog Timer, a write of 0x38 will also clear the Sleep Timer
Bit [7:0]: Reset Watchdog Timer [7:0]
interrupts not intended for waking should be disabled through
the Interrupt Mask Registers.
12.0
Sleep Mode
The CPU can only be put to sleep by the firmware. This is
accomplished by setting the Sleep bit in the System Status and
Control Register (CPU_SCR). This stops the CPU from
executing instructions, and the CPU will remain asleep until an
interrupt comes pending, or there is a reset event (either a
Power-on Reset, or a Watchdog Timer Reset).
When the CPU enters sleep mode the CPUCLK Select (Bit 1,
Table 10-4) is forced to the Internal Oscillator. The internal
oscillator recovery time is three clock cycles of the Internal
32-KHz Low-power Oscillator. The Internal 24-MHz Oscillator
restarts immediately on exiting Sleep mode. If the external
crystal oscillator is used, firmware will need to switch the clock
source for the CPU.
The Low-voltage Detection circuit (LVD) drops into fully
functional power-reduced states, and the latency for the LVD
is increased. The actual latency can be traded against power
consumption by changing Sleep Duty Cycle field of the
ECO_TR Register.
Unlike the Internal 24-MHz Oscillator, the external oscillator is
not automatically shut down during sleep. Systems that need
the external oscillator disabled in sleep mode will need to
disable the external oscillator prior to entering sleep mode. In
systems where the CPU runs off the external oscillator,
firmware will need to switch the CPU to the internal oscillator
prior to disabling the external oscillator.
The Internal 32-KHz Low-speed Oscillator remains running.
Prior to entering suspend mode, firmware can optionally
configure the 32-KHz Low-speed Oscillator to operate in a low-
power mode to help reduce the over all power consumption
(Using Bit 7, Table 10-3). This will help save approximately
5 µA; however, the trade off is that the 32-KHz Low-speed
Oscillator will be less accurate (–85% to +120% deviation).
On exiting sleep mode, once the clock is stable and the delay
time has expired, the instruction immediately following the
sleep instruction is executed before the interrupt service
routine (if enabled).
All interrupts remain active. Only the occurrence of an interrupt
will wake the part from sleep. The Stop bit in the System Status
and Control Register (CPU_SCR) must be cleared for a part
to resume out of sleep. The Global Interrupt Enable bit of the
CPU Flags Register (CPU_F) does not have any effect. Any
unmasked interrupt will wake the system up. As a result, any
The Sleep interrupt allows the microcontroller to wake up
periodically and poll system components while maintaining
very low average power consumption. The Sleep interrupt
may also be used to provide periodic interrupts during non-
sleep modes.
Document 38-08035 Rev. *F
Page 25 of 68
CY7C63310
CY7C638xx
CY7C639xx
13.0
Low-voltage Detect Control
Table 13-1. Low-voltage Control Register (LVDCR) [0x1E3] [R/W]
Bit #
Field
7
6
5
4
3
2
1
VM[2:0]
R/W
0
0
Reserved
PORLEV[1:0]
Reserved
Read/Write
Default
–
0
–
0
R/W
0
R/W
0
–
0
R/W
0
R/W
0
This register controls the configuration of the Power-on Reset / Low-voltage Detection block
Bit [7:6]: Reserved
Bit [5:4]: PORLEV[1:0]
This field controls the level below which the precision power-on-reset (PPOR) detector generates a reset
0 0 = 2.7V Range (trip near 2.6V)
0 1 = 3V Range (trip near 2.9V)
1 0 = 5V Range, >4.75V (trip near 4.65V)
1 1 = PPOR will not generate a reset, but values read from the Voltage Monitor Comparators Register (Table 13-2) give the
internal PPOR comparator state with trip point set to the 3V range setting
Bit 3: Reserved
Bit [2:0]: VM[2:0]
This field controls the level below which the low-voltage-detect trips—possibly generating an interrupt and the level at which the
Flash is enabled for operation.
LVDTripPoint
(V) Min
LVD Trip
Point (V) Typ
LVDTripPoint
(V) Max
VM[2:0]
000
001
010
011
2.69
2.90
3.00
3.11
4.46
4.61
4.70
4.78
2.70
2.92
3.02
3.13
4.48
4.64
4.73
4.82
2.72
2.94
3.04
3.15
4.51
4.67
4.76
4.85
100
101
110
111
13.0.1 POR Compare State
Table 13-2. Voltage Monitor Comparators Register (VLTCMP) [0x1E4] [R]
Bit #
Field
7
6
5
4
3
2
1
LVD
R
0
PPOR
R
Reserved
Read/Write
Default
–
0
–
0
–
0
–
0
–
0
–
0
0
0
This read-only register allows reading the current state of the Low-voltage-Detection and Precision-Power-On-Reset compar-
ators
Bit [7:2]: Reserved
Bit 1: LVD
This bit is set to indicate that the low-voltage-detect comparator has tripped, indicating that the supply voltage has gone below
the trip point set by VM[2:0] (See Table 13-1)
0 = No low-voltage-detect event
1= A low-voltage-detect has tripped
Bit 0: PPOR
This bit is set to indicate that the precision-power-on-reset comparator has tripped, indicating that the supply voltage is below
the trip point set by PORLEV[1:0]
0 = No precision-power-on-reset event
1= A precision-power-on-reset event has tripped
Document 38-08035 Rev. *F
Page 26 of 68
CY7C63310
CY7C638xx
CY7C639xx
13.0.2 ECO Trim Register
Table 13-3. ECO (ECO_TR) [0x1EB] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Sleep Duty Cycle [1:0]
Reserved
Read/Write
Default
R/W
0
R/W
0
–
0
–
0
–
0
–
0
–
0
–
0
This register controls the ratios (in numbers of 32-KHz clock periods) of “on” time versus “off” time for LVD and POR detection
circuit
Bit [7:6]: Sleep Duty Cycle [1:0]
0 0 = 128 periods of the Internal 32-KHz Low-speed Oscillator
0 1 = 512 periods of the Internal 32-KHz Low-speed Oscillator
1 0 = 32 periods of the Internal 32-KHz Low-speed Oscillator
1 1 = 8 periods of the Internal 32-KHz Low-speed Oscillator
14.0
14.1
General-purpose I/O Ports
Port Data Registers
14.1.1 P0 Data
Table 14-1. P0 Data Register (P0DATA)[0x00] [R/W]
Bit #
Field
7
6
P0.6/TIO1
R/W
5
P0.5/TIO0
R/W
4
P0.4/INT2
R/W
3
P0.3/INT1
R/W
2
P0.2/INT0
R/W
1
0
P0.0/CLKIN
R/W
P0.7
R/W
0
P0.1/CLKOUT
Read/Write
Default
R/W
0
0
0
0
0
0
0
This register contains the data for Port 0. Writing to this register sets the bit values to be output on output enabled pins. Reading
from this register returns the current state of the Port 0 pins.
Bit 7: P0.7 Data
P0.7 only exists in the CY7C638xx and CY7C639xx
Bit [6:5]: P0.6–P0.5 Data / TIO1 and TIO0
Beside their use as the P0.6–P0.5 GPIOs, these pins can also be used for the alternate functions as the Capture Timer input or
Timer output pins (TIO1 and TIO0). To configure the P0.5 and P0.6 pins, refer to the P0.5/TIO0–P0.6/TIO1 Configuration Register
(Table 14-9)
The use of the pins as the P0.6–P0.5 GPIOs and the alternate functions exist in all the enCoRe II parts
Bit [4:2]: P0.4–P0.2 Data / INT2 – INT0
Beside their use as the P0.4–P0.2 GPIOs, these pins can also be used for the alternate functions as the Interrupt pins
(INT0–INT2). To configure the P0.4–P0.2 pins, refer to the P0.2/INT0–P0.4/INT2 Configuration Register (Table 14-8)
The use of the pins as the P0.4–P0.2 GPIOs and the alternate functions exist in all the enCoRe II parts
Bit 1: P0.1/CLKOUT
Beside its use as the P0.1 GPIO, this pin can also be used for the alternate function as the CLK OUT pin. To configure the P0.1
pin, refer to the P0.1/CLKOUT Configuration Register (Table 14-7)
Bit 0: P0.0/CLKIN
Beside its use as the P0.0 GPIO, this pin can also be used for the alternate function as the CLKIN pin. To configure the P0.0
pin, refer to the P0.0/CLKIN Configuration Register (Table 14-6)
Document 38-08035 Rev. *F
Page 27 of 68
CY7C63310
CY7C638xx
CY7C639xx
14.1.2 P1 Data
Table 14-2. P1 Data Register (P1DATA) [0x01] [R/W]
Bit #
Field
7
6
5
4
P1.4/SCLK
R/W
3
P1.3/SSEL
R/W
2
P1.2/VREG
R/W
1
0
P1.0/D+
R/W
0
P1.7
R/W
0
P1.6/SMISO
P1.5/SMOSI
P1.1/D–
R/W
0
Read/Write
Default
R/W
0
R/W
0
0
0
0
This register contains the data for Port 1. Writing to this register sets the bit values to be output on output enabled pins. Reading
from this register returns the current state of the Port 1 pins.
Bit 7: P1.7 Data
P1.7 only exists in the CY7C638xx and CY7C639xx
Bit [6:3]: P1.6–P1.3 Data/SPI Pins (SMISO, SMOSI, SCLK, SSEL)
Beside their use as the P1.6–P1.3 GPIOs, these pins can also be used for the alternate function as the SPI interface pins. To
configure the P1.6–P1.3 pins, refer to the P1.3–P1.6 Configuration Register (Table 14-14)
The use of the pins as the P1.6–P1.3 GPIOs and the alternate functions exist in all the enCoRe II parts.
Bit 2: P1.2/VREG
On the CY7C639xx, this pin can be used as the P1.2 GPIO or the VREG output. If the VREG output is enabled (Bit 0
Table 19-1 is set), a 3.3V source is placed on the pin and the GPIO function of the pin is disabled
On the CY7C63813, this pin can only be used as the VREG output when USB mode is enabled. In non-USB mode, this pin can
be used as the P1.2 GPIO
The VREG output is not available in the CY7C63310 and CY7C63801
Bit [1:0]: P1.1–P1.0 / D– and D+
When USB mode is disabled (Bit 7 in Table 21-1 is clear), the P1.1 and P1.0 bits are used to control the state of the P1.0 and
P1.1 pins. When the USB mode is enabled, the P1.1 and P1.0 pins are used as the D– and D+ pins respectively. If the USB
Force State bit (Bit 0 in Table 18-1) is set, the state of the D– and D+ pins can be controlled by writing to the D– and D+ bits
14.1.3 P2 Data
Table 14-3. P2 Data Register (P2DATA) [0x02] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
P2.7–P2.2
P2.1–P2.0
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
This register contains the data for Port 2. Writing to this register sets the bit values to be output on output enabled pins. Reading
from this register returns the current state of the Port 2 pins
Bit [7:2]: P2 Data [7:2]
P2.7–P2.2 only exist in the CY7C639xx. Note that the CY7C63903-PVXC (28 pin SSOP package) only has P2.7–P2.4
Bit [1:0]: P2 Data [1:0]
P2.1–P2.0 only exist in the CY7C63823 and CY7C639xx (except the CY7C63903-PVXC 28 pin SSOP package)
14.1.4 P3 Data
Table 14-4. P3 Data Register (P3DATA) [0x03] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
P3.7–P3.2
P3.1–P3.0
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
This register contains the data for Port 3. Writing to this register sets the bit values to be output on output enabled pins. Reading
from this register returns the current state of the Port 3 pins
Bit [7:2]: P3 Data [7:2]
P3.7–P3.2 only exist in the CY7C639xx. Note that the CY7C63903-PVXC 28 pin SSOP package only has P3.7–P3.4
Bit [1:0]: P3 Data [1:0]
P3.1–P3.0 only exist in the CY7C63823 and CY7C639xx (except the CY7C63903-PVXC 28 pin SSOP package)
Document 38-08035 Rev. *F
Page 28 of 68
CY7C63310
CY7C638xx
CY7C639xx
14.1.5 P4 Data
Table 14-5. P4 Data Register (P4DATA) [0x04] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Reserved
P4.3–P4.0
Read/Write
Default
R
0
R
0
R
0
R
0
R/W
0
R/W
0
R/W
0
R/W
0
This register contains the data for Port 4. Writing to this register sets the bit values to be output on output-enabled pins. Reading
from this register returns the current state of the Port 2 pins
Bit [7:4]: Reserved
Bit [3:0]: P4 Data [3:0]
P4.3–P4.0 only exist in the CY7C639xx except the CY7C63903-PVXC
set, the pin is in high-impedance state. If the corresponding bit
in the Port Data Register is clear, the pin is driven low.
14.2
GPIO Port Configuration
All the GPIO configuration registers have common configu-
ration controls. The following are the bit definitions of the GPIO
configuration registers
When clear, the output is driven low or high.
14.2.6 Pull-up Enable
14.2.1 Int Enable
When set the pin has a 7K pull-up to V (or VREG for ports
CC
with V3.3 enabled).
When set, the Int Enable bit allows the GPIO to generate inter-
rupts. Interrupt generate can occur regardless of whether the
pin is configured for input or output. All interrupts are edge
sensitive, however for any interrupt that is shared by multiple
sources (i.e., Ports 2, 3, and 4) all inputs must be deasserted
before a new interrupt can occur.
When clear, the pull-up is disabled.
14.2.7 Output Enable
When set, the output driver of the pin is enabled.
When clear, the output driver of the pin is disabled.
For pins with shared functions there are some special cases.
When clear, the corresponding interrupt is disabled on the pin.
It is possible to configure GPIOs as outputs, enable the
interrupt on the pin and then to generate the interrupt by
driving the appropriate pin state. This is useful in test and may
have value in applications as well.
P0.0(CLKIN) and P0.1(CLKOUT) can not be output enabled
when the crystal oscillator is enabled. Output enables for these
pins are overridden by XOSC Enable.
P1.2(VREG), P1.3(SSEL), P1.4(SCLK), P1.5(SMOSI) and
P1.6(SMISO) can be used for their dedicated functions or for
GPIO. To enable the pin for GPIO use clear the corresponding
SPI Use bit or the Output Enable will have no effect.
14.2.2 Int Act Low
When set, the corresponding interrupt is active on the falling
edge.
When clear, the corresponding interrupt is active on the rising
edge.
14.2.8 VREG Output / SPI Use
The P1.2(VREG), P1.3(SSEL), P1.4(SCLK), P1.5(SMOSI)
and P1.6(SMISO) pins can be used for their dedicated
functions or for GPIO. To enable the pin for GPIO, clear the
corresponding VREG Output or SPI Use bit. The SPI function
controls the output enable for its dedicated function pins when
their GPIO enable bit is clear. The VREG output is not
available on the CY7C63801 and CY7C63310.
14.2.3 TTL Thresh
When set, the input has TTL threshold. When clear, the input
has standard CMOS threshold.
14.2.4 High Sink
When set, the output can sink up to 50 mA.
When clear, the output can sink up to 8 mA.
14.2.9 3.3V Drive
The
P1.3(SSEL),
P1.4(SCLK),
P1.5(SMOSI)
and
On the CY7C639xx, only the P3.7, P2.7, P0.1, and P0.0 have
50-mA sink drive capability. Other pins have 8-mA sink drive
capability.
P1.6(SMISO) pins have an alternate voltage source from the
voltage regulator. If the 3.3V Drive bit is set a high level is
driven from the voltage regulator instead of from V . Setting
the 3.3V Drive bit does not enable the voltage regulator. That
must be done explicitly by setting the VREG Enable bit in the
VREGCR Register (Table 19-1).
CC
On the CY7C638xx, only the P1.7–P1.3 have 50-mA sink drive
capability. Other pins have 8-mA sink drive capability.
14.2.5 Open Drain
When set, the output on the pin is determined by the Port Data
Register. If the corresponding bit in the Port Data Register is
Document 38-08035 Rev. *F
Page 29 of 68
CY7C63310
CY7C638xx
CY7C639xx
Vsupply
VREG
3.3V Drive
(On Designated
Pins Only)
Pull-Up Enable
Output Enable
VREG
VCC
Data Out
R
UP
Open Drain
Port Data
GPIO PIN
High Sink
VREG GND
Vsupply GND
Data In
TTL Threshold
Figure 14-1. Block Diagram of a GPIO
14.2.10 P0.0/CLKIN Configuration
Table 14-6. P0.0/CLKIN Configuration (P00CR) [0x05] [R/W]
Bit #
Field
7
6
Int Enable
R/W
5
Int Act Low
R/W
4
TTL Thresh
R/W
3
High Sink
R/W
2
1
0
Reserved
Open Drain
Pull-up Enable
Output Enable
Read/Write
Default
--
0
R/W
0
R/W
0
R/W
0
0
0
0
0
This pin is shared between the P0.0 GPIO use and the CLKIN pin for the external crystal oscillator. When the external oscillator
is enabled the settings of this register are ignored
The use of the pin as the P0.0 GPIO is available in all the enCoRe II parts. The alternate function of the pin as the CLKIN is only
available in the CY7C639xx. When the external oscillator is enabled (the XOSC Enable bit of the CLKIOCR Register is
set—Table 10-8), the GPIO function of the pin is disabled
The 50-mA sink drive capability is only available in the CY7C639xx. In the CY7C638xx, only 8-mA sink drive capability is available
on this pin regardless of the setting of the High Sink bit
14.2.11 P0.1/CLKOUT Configuration
Table 14-7. P0.1/CLKOUT Configuration (P01CR) [0x06] R/W]
Bit #
Field
7
CLK Output
R/W
6
Int Enable
R/W
5
Int Act Low
R/W
4
TTL Thresh
R/W
3
High Sink
R/W
2
Open Drain
R/W
1
0
Pull-up Enable
Output Enable
Read/Write
Default
R/W
0
R/W
0
0
0
0
0
0
0
This pin is shared between the P0.1 GPIO use and the CLKOUT pin for the external crystal oscillator. When the external oscillator
is enabled the settings of this register are ignored. When CLK output is set, the internally selected clock is sent out onto
P0.1CLKOUT pin.
The use of the pin as the P0.1 GPIO is available in all the enCoRe II parts. The alternate function of the pin as the CLKOUT is
only available in the CY7C639xx. When the external oscillator is enabled (the XOSC Enable bit of the CLKIOCR Register is
set—Table 10-8), the GPIO function of the pin is disabled
The 50-mA sink drive capability is only available in the CY7C639xx. In the CY7C638xx, only 8-mA sink drive capability is available
on this pin regardless of the setting of the High Sink bit
Bit 7: CLK Output
0 = The clock output is disabled
1 = The clock selected by the CLK Select field (Bit [1:0] of the CLKIOCR Register—Table 10-8) is driven out to the pin
Document 38-08035 Rev. *F
Page 30 of 68
CY7C63310
CY7C638xx
CY7C639xx
14.2.12 P0.2/INT0 – P0.4/INT2 Configuration
Table 14-8. P0.2/INT0–P0.4/INT2 Configuration (P02CR–P04CR) [0x07–0x09] [R/W]
Bit #
Field
7
6
5
Int Act Low
R/W
4
TTL Thresh
R/W
3
2
Open Drain
R/W
1
0
Reserved
Reserved
Pull-up Enable
Output Enable
Read/Write
Default
–
0
–
0
–
0
R/W
0
R/W
0
0
0
0
These registers control the operation of pins P0.2–P0.4 respectively. These pins are shared between the P0.2–P0.4 GPIOs and
the INT0–INT2. These registers exist in all enCoRe II parts. The INT0–INT2 interrupts are different than all the other GPIO
interrupts. These pins are connected directly to the interrupt controller to provide three edge-sensitive interrupts with independent
interrupt vectors. These interrupts occur on a rising edge when Int act Low is clear and on a falling edge when Int act Low is set.
These pins are enabled as interrupt sources in the interrupt controller registers (Table 17-8 and Table 17-6).
To use these pins as interrupt inputs configure them as inputs by clearing the corresponding Output Enable. If the INT0–INT2
pins are configured as outputs with interrupts enabled, firmware can generate an interrupt by writing the appropriate value to the
P0.2, P0.3 and P0.4 data bits in the P0 Data Register
Regardless of whether the pins are used as Interrupt or GPIO pins the Int Enable, Int act Low, TTL Threshold, Open Drain, and
Pull-up Enable bits control the behavior of the pin
The P0.2/INT0–P0.4/INT2 pins are individually configured with the P02CR (0x07), P03CR (0x08), and P04CR (0x09) respec-
tively.
Note: Changing the state of the Int Act Low bit can cause an unintentional interrupt to be generated. When configuring these
interrupt sources, it is best to follow the following procedure:
1. Disable interrupt source
2. Configure interrupt source
3. Clear any pending interrupts from the source
4. Enable interrupt source
14.2.13 P0.5/TIO0 – P0.6/TIO1 Configuration
Table 14-9. P0.5/TIO0 – P0.6/TIO1 Configuration (P05CR–P06CR) [0x0A–0x0B] [R/W]
Bit #
Field
7
6
Int Enable
R/W
5
Int Act Low
R/W
4
TTL Thresh
R/W
3
2
Open Drain
R/W
1
0
TIO Output
Reserved
Pull-up Enable
Output Enable
Read/Write
Default
–
0
–
0
R/W
0
R/W
0
0
0
0
0
These registers control the operation of pins P0.5 through P0.6, respectively. These registers exist in all enCoRe II parts.
P0.5 and P0.6 are shared with TIO0 and TIO1, respectively. To use these pins as Capture Timer inputs, configure them as inputs
by clearing the corresponding Output Enable. To use TIO0 and TIO1 as Timer outputs, set the TIOx Output and Output Enable
bits. If these pins are configured as outputs and the TIO Output bit is clear, firmware can control the TIO0 and TIO1 inputs by
writing the value to the P0.5 and P0.6 data bits in the P0 Data Register
Regardless of whether either pin is used as a TIO or GPIO pin the Int Enable, Int act Low, TTL Threshold, Open Drain, and Pull-
up Enable control the behavior of the pin.
TIO0(P0.5) when enabled outputs a positive pulse from the 1024-µs interval timer. This is the same signal that is used internally
to generate the 1024-µs timer interrupt. This signal is not gated by the interrupt enable state.
TIO1(P0.6) when enabled outputs a positive pulse from the programmable interval timer. This is the same signal that is used
internally to generate the programmable timer interval interrupt. This signal is not gated by the interrupt enable state
The P0.5/TIO0 and P0.6/TIO1 pins are individually configured with the P05CR (0x0A) and P06CR (0x0B), respectively
14.2.14 P0.7 Configuration
Table 14-10. P0.7 Configuration (P07CR) [0x0C] [R/W]
Bit #
Field
7
6
Int Enable
R/W
5
Int Act Low
R/W
4
TTL Thresh
R/W
3
2
Open Drain
R/W
1
0
Reserved
Reserved
Pull-up Enable
Output Enable
Read/Write
Default
–
0
–
0
R/W
0
R/W
0
0
0
0
0
This register controls the operation of pin P0.7. The P0.7 pin only exists in the CY7C638xx and CY7C639xx
Document 38-08035 Rev. *F
Page 31 of 68
CY7C63310
CY7C638xx
CY7C639xx
14.2.15 P1.0/D+ Configuration
Table 14-11. P1.0/D+ Configuration (P10CR) [0x0D] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Reserved
Int Enable
Int Act Low
Reserved
PS/2 Pull-up
Enable
Output Enable
Read/Write
Default
R/W
0
R/W
0
R/W
0
–
0
–
0
–
0
R/W
0
R/W
0
This register controls the operation of the P1.0 (D+) pin when the USB interface is not enabled, allowing the pin to be used as
a PS2 interface or a GPIO. See Table 21-1 for information on enabling USB. When USB is enabled, none of the controls in this
register have any affect on the P1.0 pin.
Note: The P1.0 is an open drain only output. It can actively drive a signal low, but cannot actively drive a signal high.
Bit 1: PS/2 Pull-up Enable
0 = Disable the 5K-ohm pull-up resistors
1 = Enable 5K-ohm pull-up resistors for both P1.0 and P1.1. Enable the use of the P1.0 (D+) and P1.1 (D–) pins as a PS2 style
interface
14.2.16 P1.1/D– Configuration
Table 14-12. P1.1/D– Configuration (P11CR) [0x0E] [R/W]
Bit #
Field
7
6
Int Enable
R/W
5
Int Act Low
R/W
4
3
2
Open Drain
R/W
1
0
Reserved
Reserved
Reserved
Output Enable
Read/Write
Default
–
0
–
0
–
0
–
0
R/W
0
0
0
0
This register controls the operation of the P1.1 (D–) pin when the USB interface is not enabled, allowing the pin to be used as
a PS2 interface or a GPIO. See Table 21-1 for information on enabling USB. When USB is enabled, none of the controls in this
register have any affect on the P1.1 pin. When USB is disabled, the 5-Kohm pull-up resistor on this pin can be enabled by the
PS/2 Pull-up Enable bit of the P10CR Register (Table 14-11)
Note: There is no 2-mA sourcing capability on this pin. The pin can only sink 5 mA at V
(Section 26.0)
OL3
14.2.17 P1.2 Configuration
Table 14-13. P1.2 Configuration (P12CR) [0x0F] [R/W]
Bit #
Field
7
CLK Output
R/W
6
Int Enable
R/W
5
Int Act Low
R/W
4
3
2
1
0
TTL Threshold
Reserved
Open Drain
Pull-up Enable
Output Enable
Read/Write
Default
R/W
0
–
0
R/W
0
R/W
0
R/W
0
0
0
0
This register controls the operation of the P1.2
Bit 7: CLK Output
0 = The internally selected clock is not sent out onto P1.2 pin
1 = This CLK Output is used to observe connected external crystal oscillator clock connected in CY7C639xx. When CLK Output
is set, the internally selected clock is sent out onto P1.2 pin
14.2.18 P1.3 Configuration (SSEL)
Table 14-14. P1.3 Configuration (P13CR) [0x10] [R/W]
Bit #
Field
7
6
Int Enable
R/W
5
Int Act Low
R/W
4
3.3V Drive
R/W
3
High Sink
R/W
2
Open Drain
R/W
1
0
Reserved
Pull-up Enable
Output Enable
Read/Write
Default
–
0
R/W
0
R/W
0
0
0
0
0
0
This register controls the operation of the P1.3 pin. This register exists in all enCoRe II parts
The P1.3 GPIO’s threshold is always set to TTL
When the SPI hardware is enabled, the output enable and output state of the pin is controlled by the SPI circuitry. When the SPI
hardware is disabled, the pin is controlled by the Output Enable bit and the corresponding bit in the P1 data register.
Regardless of whether the pin is used as an SPI or GPIO pin the Int Enable, Int act Low, 3.3V Drive, High Sink, Open Drain, and
Pull-up Enable control the behavior of the pin
The 50-mA sink drive capability is only available in the CY7C638xx. In the CY7C639xx, only 8-mA sink drive capability is available
on this pin regardless of the setting of the High Sink bit
Document 38-08035 Rev. *F
Page 32 of 68
CY7C63310
CY7C638xx
CY7C639xx
14.2.19 P1.4 – P1.6 Configuration (SCLK, SMOSI, SMISO)
Table 14-15. P1.4–P1.6 Configuration (P14CR–P16CR) [0x11–0x13] [R/W]
Bit #
Field
7
SPI Use
R/W
0
6
Int Enable
R/W
5
Int Act Low
R/W
4
3.3V Drive
R/W
3
High Sink
R/W
2
Open Drain
R/W
1
0
Pull-up Enable
Output Enable
Read/Write
Default
R/W
0
R/W
0
0
0
0
0
0
These registers control the operation of pins P1.4–P1.6, respectively. These registers exist in all enCoRe II parts
The P1.4–P1.6 GPIO’s threshold is always set to TTL
When the SPI hardware is enabled, pins that are configured as SPI Use have their output enable and output state controlled by
the SPI circuitry. When the SPI hardware is disabled or a pin has its SPI Use bit clear, the pin is controlled by the Output Enable
bit and the corresponding bit in the P1 data register.
Regardless of whether any pin is used as an SPI or GPIO pin the Int Enable, Int act Low, 3.3V Drive, High Sink, Open Drain,
and Pull-up Enable control the behavior of the pin
The 50-mA sink drive capability is only available in the CY7C638xx. In the CY7C639xx, only 8-mA sink drive capability is available
on this pin regardless of the setting of the High Sink bit
Bit 7: SPI Use
0 = Disable the SPI alternate function. The pin is used as a GPIO
1 = Enable the SPI function. The SPI circuitry controls the output of the pin
Important Note for Comm Modes 01 or 10 (SPI Master or SPI Slave, see Table 15-2):
When configured for SPI (SPI Use = 1 and Comm Modes [1:0] = SPI Master or SPI Slave mode), the input/output direction of
pins P1.3, P1.5, and P1.6 is set automatically by the SPI logic. However, pin P1.4's input/output direction is NOT automatically
set; it must be explicitly set by firmware. For SPI Master mode, pin P1.4 must be configured as an output; for SPI Slave mode,
pin P1.4 must be configured as an input.
14.2.20 P1.7 Configuration
Table 14-16. P1.7 Configuration (P17CR) [0x14] [R/W]
Bit #
Field
7
6
Int Enable
R/W
5
Int Act Low
R/W
4
TTL Thresh
R/W
3
High Sink
R/W
2
Open Drain
R/W
1
0
Reserved
Pull-up Enable
Output Enable
Read/Write
Default
–
0
R/W
1
R/W
0
0
0
0
0
0
This register controls the operation of pin P1.7. This register only exists in CY7C638xx and CY7C639xx
The 50-mA sink drive capability is only available in the CY7C638xx. In the CY7C639xx, only 8-mA sink drive capability is available
on this pin regardless of the setting of the High Sink bit
The P1.7 GPIO’s threshold is always set to TTL
14.2.21 P2 Configuration
Table 14-17. P2 Configuration (P2CR) [0x15] [R/W]
Bit #
Field
7
6
Int Enable
R/W
5
Int Act Low
R/W
4
TTL Thresh
R/W
3
High Sink
R/W
2
Open Drain
R/W
1
0
Reserved
Pull-up Enable
Output Enable
Read/Write
Default
–
0
R/W
0
R/W
0
0
0
0
0
0
This register only exists in CY7C638xx and CY7C639xx. In CY7C638xx this register controls the operation of pins P2.0–P2.1.
In the CY7C639xx, this register controls the operation of pins P2.0–P2.7
The 50-mA sink drive capability is only available on pin P2.7 and only on the CY7C639xx. In the CY7C638xx, only 8-mA sink
drive capability is available on this pin regardless of the setting of the High Sink bit
14.2.22 P3 Configuration
Table 14-18. P3 Configuration (P3CR) [0x16] [R/W]
Bit #
Field
7
6
Int Enable
R/W
5
Int Act Low
R/W
4
TTL Thresh
R/W
3
High Sink
R/W
2
Open Drain
R/W
1
0
Reserved
Pull-up Enable
Output Enable
Read/Write
Default
–
0
R/W
1
R/W
0
0
0
0
0
0
This register exists in CY7C638xx and CY7C639xx. In CY7C638xx this register controls the operation of pins P3.0–P3.1. In the
CY7C639xx, this register controls the operation of pins P3.0–P3.7
The 50-mA sink drive capability is only available on pin P3.7 and only on the CY7C639xx. In the CY7C638xx, only 8-mA sink
drive capability is available on this pin regardless of the setting of the High Sink bit
Document 38-08035 Rev. *F
Page 33 of 68
CY7C63310
CY7C638xx
CY7C639xx
14.2.23 P4 Configuration
Table 14-19. P4 Configuration (P4CR) [0x17] [R/W]
Bit #
Field
7
6
Int Enable
R/W
5
Int Act Low
R/W
4
TTL Thresh
R/W
3
2
Open Drain
R/W
1
0
Reserved
Reserved
Pull-up Enable
Output Enable
Read/Write
Default
–
0
–
0
R/W-
0
R/W
0
0
0
0
0
This register exists only in the CY7C639xx. This register controls the operation of pins P4.0–P4.3
15.0
Serial Peripheral Interface (SPI)
The SPI Master/Slave Interface core logic runs on the SPI
clock domain, making its functionality independent of system
clock speed. SPI is a four pin serial interface comprised of a
clock, an enable and two data pins.
15.1
SPI Data Register
Table 15-1. SPI Data Register (SPIDATA) [0x3C] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
SPIData[7:0]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
When read, this register returns the contents of the receive buffer. When written, it loads the transmit holding register
Bit [7:0]: SPI Data [7:0]
When an interrupt occurs to indicate to firmware that a byte of
receive data is available, or the transmitter holding register is
empty, firmware has 7 SPI clocks to manage the buffers—to
empty the receiver buffer, or to refill the transmit holding
register. Failure to meet this timing requirement will result in
incorrect data transfer.
Document 38-08035 Rev. *F
Page 34 of 68
CY7C63310
CY7C638xx
CY7C639xx
15.2
SPI Configure Register
Table 15-2. SPI Configure Register (SPICR) [0x3D] [R/W]
Bit #
Field
7
Swap
R/W
0
6
LSB First
R/W
5
4
3
CPOL
R/W
0
2
CPHA
R/W
0
1
0
Comm Mode
SCLK Select
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
0
Bit 7: Swap
0 = Swap function disabled
1 = The SPI block swaps its use of SMOSI and SMISO. Among other things, this can be useful in implementing single wire SPI-
like communications
Bit 6: LSB First
0 = The SPI transmits and receives the MSB (Most Significant Bit) first
1 = The SPI transmits and receives the LSB (Least Significant Bit) first.
Bit [5:4]: Comm Mode [1:0]
0 0: All SPI communication disabled
0 1: SPI master mode
1 0: SPI slave mode
1 1: Reserved
Bit 3: CPOL
This bit controls the SPI clock (SCLK) idle polarity
0 = SCLK idles low
1 = SCLK idles high
Bit 2: CPHA
The Clock Phase bit controls the phase of the clock on which data is sampled. Table 15-3 below shows the timing for the various
combinations of LSB First, CPOL, and CPHA
Bit [1:0]: SCLK Select
This field selects the speed of the master SCLK. When in master mode, SCLK is generated by dividing the base CPUCLK
Important Note for Comm Modes 01b or 10b (SPI Master or SPI Slave):
When configured for SPI, (SPI Use = 1—Table 14-15), the input/output direction of pins P1.3, P1.5, and P1.6 is set automati-
cally by the SPI logic. However, pin P1.4's input/output direction is NOT automatically set; it must be explicitly set by firmware.
For SPI Master mode, pin P1.4 must be configured as an output; for SPI Slave mode, pin P1.4 must be configured as an input.
Document 38-08035 Rev. *F
Page 35 of 68
CY7C63310
CY7C638xx
CY7C639xx
Table 15-3. SPI Mode Timing vs. LSB First, CPOL and CPHA
LSB First CPHA CPOL
Diagram
0
0
0
0
0
1
0
1
0
SCLK
SSEL
DAT A
X
MSB
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
LSB
X
SC LK
SSEL
D AT A
X
MS B
B it 7
B it 6
B it 5
B it 4
B it 3
B it 2
LS B
X
SCLK
SSEL
DAT A
X
MSB
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
LSB
X
0
1
1
SCLK
SSEL
DATA
X
MSB
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
LSB
X
1
1
0
0
0
1
SCLK
SSEL
DATA
X
LSB
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
MSB
X
SCLK
SSEL
DATA
X
LSB
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
MSB
X
1
1
1
1
0
1
SCLK
SSEL
DATA
X
LSB
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
MSB
X
SCLK
SSEL
DATA
X
LSB
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
MSB
X
Document 38-08035 Rev. *F
Page 36 of 68
CY7C63310
CY7C638xx
CY7C639xx
Table 15-4. SPI SCLK Frequency
SCLK Frequency when CPUCLK =
SCLK
Select
CPUCLK
Divisor
12 MHz
2 MHz
24 MHz
4 MHz
00
01
10
11
6
12
48
96
1 MHz
2 MHz
250 KHz
125 KHz
500 KHz
250 KHz
15.3
SPI Interface Pins
The SPI interface uses the P1.3–P1.6 pins. These pins are
configured using the P1.3 and P1.4–P1.6 Configuration.
16.0
Timer Registers
All timer functions of the enCoRe II are provided by a single
timer block. The timer block is asynchronous from the CPU
clock.
16.1
Registers
16.1.1 Free-running Timer Low-order Byte
Table 16-1. Free-running Timer Low-order Byte (FRTMRL) [0x20] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Free-running Timer [7:0]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:0]: Free-running Timer [7:0]
This register holds the low-order byte of the 16-bit free-running timer. Reading this register causes the high-order byte to be
moved into a holding register allowing an automatic read of all 16 bits simultaneously.
For reads, the actual read occurs in the cycle when the low order is read. For writes, the actual time the write occurs is the cycle
when the high order is written.
When reading the Free Running Timer, the low-order byte should be read first and the high-order second. When writing, the low-
order byte should be written first then the high-order byte
16.1.2 Free-running Timer High-order Byte
Table 16-2. Free-running Timer High-order Byte (FRTMRH) [0x21] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Free-running Timer [15:8]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:0]: Free-running Timer [15:8]
When reading the Free-running Timer, the low-order byte should be read first and the high-order second. When writing, the low-
o order byte should be written first then the high-order byte
16.1.3 Timer Capture 0 Rising
Table 16-3. Timer Capture 0 Rising (TCAP0R) [0x22] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Capture 0 Rising [7:0]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:0]: Capture 0 Rising [7:0]
This register holds the value of the Free-running Timer when the last rising edge occurred on the TCAP0 input. When Capture 0
is in 8-bit mode, the bits that are stored here are selected by the Prescale [2:0] bits in the Timer Configuration register. When
Capture 0 is in 16-bit mode this register holds the lower order 8 bits of the 16-bit timer
Document 38-08035 Rev. *F
Page 37 of 68
CY7C63310
CY7C638xx
CY7C639xx
16.1.4 Capture 1 Rising
Table 16-4. Timer Capture 1 Rising (TCAP1R) [0x23] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Capture 1 Rising [7:0]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:0]: Capture 1 Rising [7:0]
This register holds the value of the Free-running Timer when the last rising edge occurred on the TCAP1 input. The bits that are
stored here are selected by the Prescale [2:0] bits in the Timer Configuration register. When Capture 0 is in 16-bit mode this
register holds the high-order 8 bits of the 16-bit timer from the last Capture 0 rising edge. When Capture 0 is in 16-bit mode this
register will be loaded with high-order 8 bits of the 16-bit timer on TCAP0 rising edge
16.1.5 Timer Capture 0 Falling
Table 16-5. Timer Capture 0 Falling (TCAP0F) [0x24] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Capture 0 Falling [7:0]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:0]: Capture 0 Falling [7:0]
This register holds the value of the Free-running Timer when the last falling edge occurred on the TCAP0 input. When Capture
0 is in 8-bit mode, the bits that are stored here are selected by the Prescale [2:0] bits in the Timer Configuration register. When
Capture 0 is in 16-bit mode this register holds the lower-order 8 bits of the 16-bit timer
16.1.6 Timer Capture 1 Falling
Table 16-6. Timer Capture 1 Falling (TCAP1F) [0x25] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Capture 1 Falling [7:0]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:0]: Capture 1Falling [7:0]
This register holds the value of the Free-running Timer when the last falling edge occurred on the TCAP1 input. The bits that
are stored here are selected by the Prescale [2:0] bits in the Timer Configuration register. When capture 0 is in 16-bit mode this
register holds the high-order 8 bits of the 16-bit timer from the last Capture 0 falling edge. When Capture 0 is in 16-bit mode this
register will be loaded with high-order 8 bits of the 16-bit timer on TCAP0 falling edge
16.1.7 Programmable Interval Low Byte
Table 16-7. Programmable Interval Timer Low (PITMRL) [0x26] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Prog Interval Timer [7:0]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:0]: Prog Interval Timer [7:0]
This register holds the low-order byte of the 12-bit programmable interval timer. Reading this register causes the high-order byte
to be moved into a holding register allowing an automatic read of all 12 bits simultaneously
Document 38-08035 Rev. *F
Page 38 of 68
CY7C63310
CY7C638xx
CY7C639xx
16.1.8 Programmable Interval High Byte
Table 16-8. Programmable Interval Timer High (PITMRH) [0x27] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Reserved
Prog Interval Timer [11:8]
Read/Write
Default
–
0
–
0
–
0
–
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:4]: Reserved
Bit [3:0]: Prog Internal Timer [11:8]
This register holds the high-order nibble of the 12-bit programmable interval timer. Reading this register returns the high-order
nibble of the 12-bit timer at the instant that the low-order byte was last read
16.1.9 Programmable Interval Reload Low Byte
Table 16-9. Programmable Interval Reload Low (PIRL) [0x28] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Prog Interval [7:0]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:0]: Prog Interval [7:0]
This register holds the lower 8 bits of the timer. While writing into the 12-bit reload register, write lower byte first then the higher nibble
16.1.10 Programmable Interval Reload High Byte
Table 16-10. Programmable Interval Reload High (PIRH) [0x29] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Reserved
Prog Interval[11:8]
Read/Write
Default
–
0
–
0
–
0
–
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:4]: Reserved
Bit [3:0]: Prog Interval [11:8]
This register holds the higher 4 bits of the timer. While writing into the 12-bit reload register, write lower byte first then the higher nibble
Document 38-08035 Rev. *F
Page 39 of 68
CY7C63310
CY7C638xx
CY7C639xx
16.1.11 Timer Configuration
Table 16-11. Timer Configuration (TMRCR) [0x2A] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
First Edge Hold
8-bit Capture Prescale [2:0]
Cap0 16bit
Enable
Reserved
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
–
0
–
0
–
0
Bit 7: First Edge Hold
The First Edge Hold function applies to all four capture timers.
0 = The time of the most recent edge is held in the Capture Timer Data Register. If multiple edges have occurred since reading
the capture timer, the time for the most recent one will be read
1 = The time of the first occurrence of an edge is held in the Capture Timer Data Register until the data is read. Subsequent
edges are ignored until the Capture Timer Data Register is read.
Bit [6:4]: 8-bit Capture Prescale [2:0]
This field controls which 8 bits of the 16 Free Running Timer are captured when in bit mode
0 0 0 = capture timer[7:0]
0 0 1 = capture timer[8:1]
0 1 0 = capture timer[9:2]
0 1 1 = capture timer[10:3]
1 0 0 = capture timer[11:4]
1 0 1 = capture timer[12:5]
1 1 0 = capture timer[13:6]
1 1 1 = capture timer[14:7]
Bit 3: Cap0 16-bit Enable
0 = Capture 0 16-bit mode is disabled
1 = Capture 0 16-bit mode is enabled. Capture 1 is disabled and the Capture 1 rising and falling registers are used as an extension
to the Capture 0 registers—extending them to 16 bits
Bit [2:0]: Reserved
16.1.12 Capture Interrupt Enable
Table 16-12. Capture Interrupt Enable (TCAPINTE) [0x2B] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Reserved
Cap1 Fall
Enable
Cap1 Rise
Enable
Cap0 Fall
Enable
Cap0 Rise
Enable
Read/Write
Default
–
0
–
0
–
0
–
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:4]: Reserved
Bit 3: Cap1 Fall Enable
0 = Disable the capture 1 falling edge interrupt
1 = Enable the capture 1 falling edge interrupt
Bit 2: Cap1 Rise Enable
0 = Disable the capture 1 rising edge interrupt
1 = Enable the capture 1 rising edge interrupt
Bit 1: Cap0 Fall Enable
0 = Disable the capture 0 falling edge interrupt
1 = Enable the capture 0 falling edge interrupt
Bit 0: Cap0 Rise Enable
0 = Disable the capture 0 rising edge interrupt
1 = Enable the capture 0 rising edge interrupt
Document 38-08035 Rev. *F
Page 40 of 68
CY7C63310
CY7C638xx
CY7C639xx
16.1.13 Capture Interrupt Status
Table 16-13. Capture Interrupt Status (TCAPINTS) [0x2C] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Reserved
Cap1 Fall
Active
Cap1 Rise
Active
Cap0 Fall
Active
Cap0 Rise
Active
Read/Write
Default
–
0
–
0
–
0
–
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit [7:4]: Reserved
Bit 3: Cap1 Fall Active
0 = No event
1 = A falling edge has occurred on Cap1
Bit 2: Cap1 Rise Active
0 = No event
1 = A rising edge has occurred on Cap1
Bit 1: Cap0 Fall Active
0 = No event
1 = A falling edge has occurred on Cap0
Bit 0: Cap0 Rise Active
0 = No event
1 = A rising edge has occurred on Cap0
Table 17-1. Interrupt Numbers, Priorities, Vectors (contin-
17.0
Interrupt Controller
Interrupt Interrupt
The interrupt controller and its associated registers allow the
user’s code to respond to an interrupt from almost every
functional block in the enCoRe II devices. The registers
associated with the interrupt controller allow interrupts to be
disabled either globally or individually. The registers also
provide a mechanism by which a user may clear all pending
and posted interrupts, or clear individual posted or pending
interrupts.
Priority
Address
0044h
0048h
004Ch
0050h
0054h
0058h
005Ch
0060h
0064h
Name
16-bit Free Running Timer Wrap
INT2
17
18
19
PS2 Data Low
GPIO Port 2
20
21
GPIO Port 3
The following table lists all interrupts and the priorities that are
available in the enCoRe II devices.
22
GPIO Port 4
23
Reserved
Table 17-1. Interrupt Numbers, Priorities, Vectors
Interrupt Interrupt
24
Reserved
25
Sleep Timer
Priority
Address
0000h
0004h
0008h
000Ch
0010h
0014h
0018h
001Ch
0020h
0024h
0028h
002Ch
0030h
0034h
0038h
003Ch
0040h
Name
0
1
Reset
17.1
Architectural Description
POR/LVD
INT0
An interrupt is posted when its interrupt conditions occur. This
results in the flip-flop in Figure 17-1 clocking in a ‘1’. The
interrupt will remain posted until the interrupt is taken or until
it is cleared by writing to the appropriate INT_CLRx register.
2
3
SPI Transmitter Empty
SPI Receiver Full
GPIO Port 0
GPIO Port 1
INT1
4
A posted interrupt is not pending unless it is enabled by setting
its interrupt mask bit (in the appropriate INT_MSKx register).
All pending interrupts are processed by the Priority Encoder to
determine the highest priority interrupt which will be taken by
the M8C if the Global Interrupt Enable bit is set in the CPU_F
register.
5
6
7
8
EP0
9
EP1
Disabling an interrupt by clearing its interrupt mask bit (in the
INT_MSKx register) does not clear a posted interrupt, nor
does it prevent an interrupt from being posted. It simply
prevents a posted interrupt from becoming pending.
10
11
12
13
14
15
16
EP2
USB Reset
USB Active
Nested interrupts can be accomplished by re-enabling inter-
rupts inside an interrupt service routine. To do this, set the IE
bit in the Flag Register.
1-mS Interval timer
Programmable Interval Timer
Timer Capture 0
Timer Capture 1
A block diagram of the enCoRe II Interrupt Controller is shown
in Figure 17-1.
Document 38-08035 Rev. *F
Page 41 of 68
CY7C63310
CY7C638xx
CY7C639xx
Priority
Encoder
Interrupt Vector
InterruptTaken
or
INT_CLRxWrite
Posted
Interrupt
Pending
Interrupt
Interrupt
Request
M8C Core
R
1
D
Q
Interrupt
Source
(Timer,
CPU_F[0]
GIE
GPIO,etc.)
INT_MSKx
MaskBit Setting
Figure 17-1. Interrupt Controller Block Diagram
by setting GIE = 1 (care must be taken to avoid stack
overflow).
17.2
Interrupt Processing
The sequence of events that occur during interrupt processing
is as follows:
6. The ISR ends with a RETI instruction which restores the
Program Counter and Flag registers (CPU_PC and
CPU_F). The restored Flag register re-enables interrupts,
since GIE = 1 again.
1. An interrupt becomes active, either because:
a. The interrupt condition occurs (e.g., a timer expires)
b. A previously posted interrupt is enabled through an up-
date of an interrupt mask register
7. Execution resumes at the next instruction, after the one that
occurred before the interrupt. However, if there are more
pending interrupts, the subsequent interrupts will be
processed before the next normal program instruction.
c. An interrupt is pending and GIE is set from 0 to 1 in the
CPU Flag register.
2. The current executing instruction finishes.
17.3
Interrupt Latency
3. Theinternalinterruptisdispatched, taking13cycles. During
this time, the following actions occur: he MSB and LSB of
Program Counter and Flag registers (CPU_PC and
CPU_F) are stored onto the program stack by an automatic
CALL instruction (13 cycles) generated during the interrupt
acknowledge process.
The time between the assertion of an enabled interrupt and the
start of its ISR can be calculated from the following equation.
Latency = Time for current instruction to finish + Time for
internal interrupt routine to execute + Time for LJMP
instruction in interrupt table to execute.
a. The PCH, PCL, and Flag register (CPU_F) are stored
onto the program stack (in that order) by an automatic
CALL instruction (13 cycles) generated during the inter-
rupt acknowledge process
For example, if the 5-cycle JMP instruction is executing when
an interrupt becomes active, the total number of CPU clock
cycles before the ISR begins would be as follows:
(1 to 5 cycles for JMP to finish) + (13 cycles for interrupt
routine) + (7 cycles for LJMP) = 21 to 25 cycles.
In the example above, at 24 MHz, 25 clock cycles take 1.042
ms.
b. The CPU_F register is then cleared. Since this clears the
GIE bit to 0, additional interrupts are temporarily dis-
abled
c. The PCH (PC[15:8]) is cleared to zero
d. The interrupt vector is read from the interrupt controller
and its value placed into PCL (PC[7:0]). This sets the
program counter to point to the appropriate address in
the interrupt table (e.g., 0004h for the POR/LVD inter-
rupt)
17.4
Interrupt Registers
17.4.1 Interrupt Clear Register
The Interrupt Clear Registers (INT_CLRx) are used to enable
the individual interrupt sources’ ability to clear posted inter-
rupts.
4. Program execution vectors to the interrupt table. Typically,
a LJMP instruction in the interrupt table sends execution to
the user's Interrupt Service Routine (ISR) for this interrupt
When an INT_CLRx register is read, any bits that are set
indicates an interrupt has been posted for that hardware
resource. Therefore, reading these registers gives the user the
ability to determine all posted interrupts.
5. The ISR executes. Note that interrupts are disabled since
GIE = 0. In the ISR, interrupts can be re-enabled if desired
Document 38-08035 Rev. *F
Page 42 of 68
CY7C63310
CY7C638xx
CY7C639xx
Table 17-2. Interrupt Clear 0 (INT_CLR0) [0xDA] [R/W]
Bit #
Field
7
6
Sleep Timer
R/W
5
4
3
2
1
0
POR/LVD
R/W
GPIO Port 1
INT1
R/W
0
GPIO Port 0
SPI Receive
SPI Transmit
INT0
R/W
0
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
0
0
When reading this register,
0 = There’s no posted interrupt for the corresponding hardware
1 = Posted interrupt for the corresponding hardware present
Writing a ‘0’ to the bits will clear the posted interrupts for the corresponding hardware. Writing a ‘1’ to the bits AND to the ENSWINT
(Bit 7 of the INT_MSK3 Register) will post the corresponding hardware interrupt
Table 17-3. Interrupt Clear 1 (INT_CLR1) [0xDB] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
TCAP0
Prog Interval
Timer
1-ms Timer
USB Active
USB Reset
USB EP2
USB EP1
USB EP0
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
When reading this register,
0 = There’s no posted interrupt for the corresponding hardware
1 = Posted interrupt for the corresponding hardware present
Writing a ‘0’ to the bits will clear the posted interrupts for the corresponding hardware. Writing a ‘1’ to the bits AND to the ENSWINT
(Bit 7 of the INT_MSK3 Register) will post the corresponding hardware interrupt
Table 17-4. Interrupt Clear 2 (INT_CLR2) [0xDC] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Reserved
GPIO Port 4
GPIO Port 3
GPIO Port 2
PS/2 Data Low
INT2
16-bit Counter
Wrap
TCAP1
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
When reading this register,
0 = There’s no posted interrupt for the corresponding hardware
1 = Posted interrupt for the corresponding hardware present
Writing a ‘0’ to the bits will clear the posted interrupts for the corresponding hardware. Writing a ‘1’ to the bits AND to the ENSWINT
(Bit 7 of the INT_MSK3 Register) will post the corresponding hardware interrupt
17.4.2 Interrupt Mask Registers
The Enable Software Interrupt (ENSWINT) bit in INT_MSK3[7]
determines the way an individual bit value written to an
INT_CLRx register is interpreted. When is cleared, writing 1's
to an INT_CLRx register has no effect. However, writing 0's to
an INT_CLRx register, when ENSWINT is cleared, will cause
the corresponding interrupt to clear. If the ENSWINT bit is set,
any 0s written to the INT_CLRx registers are ignored.
However, 1s written to an INT_CLRx register, while ENSWINT
is set, will cause an interrupt to post for the corresponding
interrupt.
The Interrupt Mask Registers (INT_MSKx) are used to enable
the individual interrupt sources’ ability to create pending inter-
rupts.
There are four Interrupt Mask Registers (INT_MSK0,
INT_MSK1, INT_MSK2, and INT_MSK3) which may be
referred to in general as INT_MSKx. If cleared, each bit in an
INT_MSKx register prevents a posted interrupt from becoming
a pending interrupt (input to the priority encoder). However, an
interrupt can still post even if its mask bit is zero. All INT_MSKx
bits are independent of all other INT_MSKx bits.
Software interrupts can aid in debugging interrupt service
routines by eliminating the need to create system level inter-
actions that are sometimes necessary to create a hardware-
only interrupt.
If an INT_MSKx bit is set, the interrupt source associated with
that mask bit may generate an interrupt that will become a
pending interrupt.
Document 38-08035 Rev. *F
Page 43 of 68
CY7C63310
CY7C638xx
CY7C639xx
Table 17-5. Interrupt Mask 3 (INT_MSK3) [0xDE] [R/W]
Bit #
Field
7
ENSWINT
R/W
6
5
4
3
2
1
0
Reserved
Read/Write
Default
–
0
–
0
–
0
–
0
–
0
–
0
–
0
0
Bit 7: Enable Software Interrupt (ENSWINT)
0= Disable. Writing 0s to an INT_CLRx register, when ENSWINT is cleared, will cause the corresponding interrupt to clear
1= Enable. Writing 1s to an INT_CLRx register, when ENSWINT is set, will cause the corresponding interrupt to post.
Bit [6:0]: Reserved
Table 17-6. Interrupt Mask 2 (INT_MSK2) [0xDF] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Reserved
GPIO Port 4
Int Enable
GPIO Port 3
Int Enable
GPIO Port 2
Int Enable
PS/2 Data Low
Int Enable
INT2
Int Enable
16-bit Counter
Wrap Int Enable
TCAP1
Int Enable
Read/Write
Default
–
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit 7: Reserved
Bit 6: GPIO Port 4 Interrupt Enable
0 = Mask GPIO Port 4 interrupt
1 = Unmask GPIO Port 4 interrupt
Bit 5: GPIO Port 3 Interrupt Enable
0 = Mask GPIO Port 3 interrupt
1 = Unmask GPIO Port 3 interrupt
Bit 4: GPIO Port 2 Interrupt Enable
0 = Mask GPIO Port 2 interrupt
1 = Unmask GPIO Port 2 interrupt
Bit 3: PS/2 Data Low Interrupt Enable
0 = Mask PS/2 Data Low interrupt
1 = Unmask PS/2 Data Low interrupt
Bit 2: INT2 Interrupt Enable
0 = Mask INT2 interrupt
1 = Unmask INT2 interrupt
Bit 1: 16-bit Counter Wrap Interrupt Enable
0 = Mask 16-bit Counter Wrap interrupt
1 = Unmask 16-bit Counter Wrap interrupt
Bit 0: TCAP1 Interrupt Enable
0 = Mask TCAP1 interrupt
1 = Unmask TCAP1 interrupt
Document 38-08035 Rev. *F
Page 44 of 68
CY7C63310
CY7C638xx
CY7C639xx
Table 17-7. Interrupt Mask 1 (INT_MSK1) [0xE1] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
TCAP0
Int Enable
Prog Interval
Timer
Int Enable
1-ms Timer
Int Enable
USB Active
Int Enable
USB Reset
Int Enable
USB EP2
Int Enable
USB EP1
Int Enable
USB EP0
Int Enable
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit 7: TCAP0 Interrupt Enable
0 = Mask TCAP0 interrupt
1 = Unmask TCAP0 interrupt
Bit 6: Prog Interval Timer Interrupt Enable
0 = Mask Prog Interval Timer interrupt
1 = Unmask Prog Interval Timer interrupt
Bit 5: 1-ms Timer Interrupt Enable
0 = Mask 1-ms interrupt
1 = Unmask 1-ms interrupt
Bit 4: USB Active Interrupt Enable
0 = Mask USB Active interrupt
1 = Unmask USB Active interrupt
Bit 3: USB Reset Interrupt Enable
0 = Mask USB Reset interrupt
1 = Unmask USB Reset interrupt
Bit 2: USB EP2 Interrupt Enable
0 = Mask EP2 interrupt
1 = Unmask EP2 interrupt
Bit 1: USB EP1 Interrupt Enable
0 = Mask EP1 interrupt
1 = Unmask EP1 interrupt
Bit 0: USB EP0 Interrupt Enable
0 = Mask EP0 interrupt
1 = Unmask EP0 interrupt
Table 17-8. Interrupt Mask 0 (INT_MSK0) [0xE0] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
GPIO Port 1
Int Enable
Sleep Timer
Int Enable
INT1
Int Enable
GPIO Port 0
Int Enable
SPI Receive
Int Enable
SPI Transmit
Int Enable
INT0
Int Enable
POR/ LVD
Int Enable
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit 7: GPIO Port 1 Interrupt Enable
0 = Mask GPIO Port 1 interrupt
1 = Unmask GPIO Port 1 interrupt
Bit 6: Sleep Timer Interrupt Enable
0 = Mask Sleep Timer interrupt
1 = Unmask Sleep Timer interrupt
Bit 5: INT1 Interrupt Enable
0 = Mask INT1 interrupt
1 = Unmask INT1 interrupt
Bit 4: GPIO Port 0 Interrupt Enable
0 = Mask GPIO Port 0 interrupt
1 = Unmask GPIO Port 0 interrupt
Bit 3: SPI Receive Interrupt Enable
0 = Mask SPI Receive interrupt
1 = Unmask SPI Receive interrupt
Bit 2: SPI Transmit Interrupt Enable
0 = Mask SPI Transmit interrupt
1 = Unmask SPI Transmit interrupt
Bit 1: INT0 Interrupt Enable
0 = Mask INT0 interrupt
1 = Unmask INT0 interrupt
Bit 0: POR/LVD Interrupt Enable
0 = Mask POR/LVD interrupt
1 = Unmask POR/LVD interrupt
Document 38-08035 Rev. *F
Page 45 of 68
CY7C63310
CY7C638xx
CY7C639xx
17.4.3 Interrupt Vector Clear Register
Table 17-9. Interrupt Vector Clear Register (INT_VC) [0xE2] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Pending Interrupt [7:0]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
The Interrupt Vector Clear Register (INT_VC) holds the interrupt vector for the highest priority pending interrupt when read, and
when written will clear all pending interrupts
Bit [7:0]: Pending Interrupt [7:0]
8-bit data value holds the interrupt vector for the highest priority pending interrupt. Writing to this register will clear all pending
interrupts.
18.0
USB/PS2 Transceiver
Although the USB transceiver has features to assist in inter-
facing to PS/2 these features are not controlled using these
registers. These registers only control the USB interfacing
features. PS/2 interfacing options are controlled by the D+/D–
GPIO Configuration register (See Section Table 14.2.15).
18.1
USB Transceiver Configuration
Table 18-1. USB Transceiver Configure Register (USBXCR) [0x74] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
USB Pull-up
Enable
Reserved
USB Force State
Read/Write
Default
R/W
0
–
0
–
0
–
0
–
0
–
0
–
0
R/W
0
Bit 7: USB Pull-up Enable
0 = Disable the pull-up resistor on D–
1 = Enable the pull-up resistor on D–. This pull-up is to V IF VREG is not enabled or to the internally generated 3.3V when
CC
VREG is enabled
Bit [6:1]: Reserved
Bit 0: USB Force State
This bit allows the state of the USB I/O pins D- and D+ to be forced to a state while USB is enabled
0 = Disable USB Force State
1 = Enable USB Force State. Allows the D- and D+ pins to be controlled by P1.1 and P1.0 respectively when the USBIO is in
USB mode. Refer to Section 14.2.15 for more information
Document 38-08035 Rev. *F
Page 46 of 68
CY7C63310
CY7C638xx
CY7C639xx
19.0
19.1
USB Regulator Output
VREG Control
Table 19-1. VREG Control Register (VREGCR) [0x73] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Reserved
Keep Alive
VREG Enable
Read/Write
Default
–
0
–
0
–
0
–
0
–
0
–
0
R/W
0
R/W
0
Bit [7:2]: Reserved
Bit 1: Keep Alive
Keep Alive when set allows the voltage regulator to source up to 20 µA of current when voltage regulator is disabled,
P12CR[0],P12CR[7] should be cleared.
0 = Disabled
1 = Enabled
Bit 0: VREG Enable
This bit turns on the 3.3V voltage regulator. The voltage regulator only functions within specifications when V is above 4.35V.
CC
This block should not be enabled when V is below 4.35V—although no damage or irregularities will occur if it is enabled below 4.35V
CC
0 = Disable the 3.3V voltage regulator output on the VREG/P1.2 pin
1 = Enable the 3.3V voltage regulator output on the VREG/P1.2 pin. GPIO functionality of P1.2 is disabled
Note: Use of the alternate drive on pins P1.3–P1.6 requires that the VREG Enable bit be set to enable the regulator and pro-
vide the alternate voltage
• Send appropriate ACK/NAK/STALL handshakes.
20.0
USB Serial Interface Engine (SIE)
• Token type identification (SETUP, IN, or OUT). Set the
appropriate token bit once a valid token is received.
The SIE allows the microcontroller to communicate with the
USB host at low-speed data rates (1.5 Mbps). The SIE
simplifies the interface between the microcontroller and USB
by incorporating hardware that handles the following USB bus
activity independently of the microcontroller:
• Place valid received data in the appropriateendpoint FIFOs.
• Send and update the data toggle bit (Data1/0).
• Bit stuffing/unstuffing.
• Translate the encoded received data and format the data to
be transmitted on the bus.
Firmware is required to handle the rest of the USB interface
with the following tasks:
• CRC checking and generation. Flag the microcontroller if
errors exist during transmission.
• Coordinate enumeration by decoding USB device requests.
• Fill and empty the FIFOs.
• Address checking. Ignore the transactions not addressed
to the device.
• Suspend/Resume coordination.
• Verify and select Data toggle values.
Document 38-08035 Rev. *F
Page 47 of 68
CY7C63310
CY7C638xx
CY7C639xx
21.0
21.1
USB Device
USB Device Address
Table 21-1. USB Device Address (USBCR) [0x40] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
USB Enable
Device Address[6:0]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
The content of this register is cleared when a USB Bus Reset condition occurs
Bit 7: USB Enable
This bit must be enabled by firmware before the serial interface engine (SIE) will respond to USB traffic at the address specified
in Device Address [6:0]. When this bit is cleared, the USB transceiver enters power-down state. User’s firmware should clear
this bit prior to entering sleep mode to save power
0 = Disable USB device address and put the USB transceiver into power-down state
1 = Enable USB device address and put the USB transceiver into normal operating mode
Bit [6:0]: Device Address [6:0]
These bits must be set by firmware during the USB enumeration process (i.e., SetAddress) to the non-zero address assigned
by the USB host
21.2
Endpoint 0, 1, and 2 Count
Table 21-2. Endpoint 0, 1, and 2 Count (EP0CNT–EP2CNT) [0x41, 0x43, 0x45] [R/W]
Bit #
Field
7
Data Toggle
R/W
6
Data Valid
R/W
5
4
3
2
1
0
Reserved
Byte Count[3:0]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
0
0
Bit 7: Data Toggle
This bit selects the DATA packet's toggle state. For IN transactions, firmware must set this bit to the select the transmitted Data
Toggle. For OUT or SETUP transactions, the hardware sets this bit to the state of the received Data Toggle bit.
0 = DATA0
1 = DATA1
Bit 6: Data Valid
This bit is used for OUT and SETUP tokens only. This bit is cleared to ‘0’ if CRC, bitstuff, or PID errors have occurred. This bit
does not update for some endpoint mode settings
0 = Data is invalid. If enabled, the endpoint interrupt will occur even if invalid data is received
1 = Data is valid
Bit [5:4]: Reserved
Bit [3:0]: Byte Count Bit [3:0]
Byte Count Bits indicate the number of data bytes in a transaction: For IN transactions, firmware loads the count with the number
of bytes to be transmitted to the host from the endpoint FIFO. Valid values are 0 to 8 inclusive. For OUT or SETUP transactions,
the count is updated by hardware to the number of data bytes received, plus 2 for the CRC bytes. Valid values are 2–10 inclusive.
For Endpoint 0 Count Register, whenever the count updates from a SETUP or OUT transaction, the count register locks and
cannot be written by the CPU. Reading the register unlocks it. This prevents firmware from overwriting a status update on it.
Document 38-08035 Rev. *F
Page 48 of 68
CY7C63310
CY7C638xx
CY7C639xx
When the SIE writes to these registers they are locked and the
processor cannot write to them until after it has read them.
Writing to this register clears the upper four bits regardless of
the value written.
21.3
Endpoint 0 Mode
Because both firmware and the SIE are allowed to write to the
Endpoint 0 Mode and Count Registers the SIE provides an
interlocking mechanism to prevent accidental overwriting of
data.
Table 21-3. Endpoint 0 Mode (EP0MODE) [0x44] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Setup Received
IN Received
OUT Received
ACK’d Trans
Mode[3:0]
[4]
[4]
[4]
Read/Write
Default
R/C[4]
0
R/C
R/C
R/C
R/W
0
R/W
0
R/W
0
R/W
0
0
0
0
Bit 7: SETUP Received
This bit is set by hardware when a valid SETUP packet is received. It is forced HIGH from the start of the data packet phase of
the SETUP transactions until the end of the data phase of a control write transfer and cannot be cleared during this interval.
While this bit is set to ‘1’, the CPU cannot write to the EP0 FIFO. This prevents firmware from overwriting an incoming SETUP
transaction before firmware has a chance to read the SETUP data.
This bit is cleared by any non-locked writes to the register.
0 = No SETUP received
1 = SETUP received
Bit 6: IN Received
This bit when set indicates a valid IN packet has been received. This bit is updated to ‘1’ after the host acknowledges an IN data
packet.When clear, it indicates either no IN has been received or that the host didn’t acknowledge the IN data by sending ACK
handshake.
This bit is cleared by any non-locked writes to the register.
0 = No IN received
1 = IN received
Bit 5: OUT Received
This bit when set indicates a valid OUT packet has been received and ACKed. This bit is updated to ‘1’ after the last received
packet in an OUT transaction. When clear, it indicates no OUT received.
This bit is cleared by any non-locked writes to the register.
0 = No OUT received
1 = OUT received
Bit 4: ACK’d Transaction
The ACK’d transaction bit is set whenever the SIE engages in a transaction to the register’s endpoint that completes with a ACK
packet.
This bit is cleared by any non-locked writes to the register
1 = The transaction completes with an ACK
0 = The transaction does not complete with an ACK
Bit [3:0]: Mode [3:0]
The endpoint modes determine how the SIE responds to USB traffic that the host sends to the endpoint. The mode controls
how the USB SIE responds to traffic and how the USB SIE will change the mode of that endpoint as a result of host packets to
the endpoint.
Document 38-08035 Rev. *F
Page 49 of 68
CY7C63310
CY7C638xx
CY7C639xx
21.4
Endpoint 1 and 2 Mode
Table 21-4. Endpoint 1 and 2 Mode (EP1MODE – EP2MODE) [0x45, 0x46] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Stall
Reserved
NAK Int Enable
ACK’d
Transaction
Mode[3:0]
Read/Write
Default
R/W
0
R/W
0
R/W
0
R/C (Note 4)
0
R/W
0
R/W
0
R/W
0
R/W
0
Bit 7: Stall
When this bit is set the SIE will stall an OUT packet if the Mode Bits are set to ACK-OUT, and the SIE will stall an IN packet if
the mode bits are set to ACK-IN. This bit must be clear for all other modes
Bit 6: Reserved
Bit 5: NAK Int Enable
This bit when set causes an endpoint interrupt to be generated even when a transfer completes with a NAK. Unlike enCoRe,
enCoRe II family members do not generate an endpoint interrupt under these conditions unless this bit is set
0 = Disable interrupt on NAK’d transactions
1 = Enable interrupt on NAK’d transaction
Bit 4: ACK’d Transaction
The ACK’d transaction bit is set whenever the SIE engages in a transaction to the register’s endpoint that completes with an
ACK packet.
This bit is cleared by any writes to the register
0 = The transaction does not complete with an ACK
1 = The transaction completes with an ACK
Bit [3:0]: Mode [3:0]
The endpoint modes determine how the SIE responds to USB traffic that the host sends to the endpoint. The mode controls how the
USB SIE responds to traffic and how the USB SIE will change the mode of that endpoint as a result of host packets to the endpoint.
21.4.1 Endpoint 0, 1, and 2 Data Buffer
Table 21-5. Endpoint 0 Data (EP0DATA) [0x50-0x57] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Endpoint 0 Data Buffer [7:0]
Read/Write
Default
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Unknown
Unknown
Unknown
Unknown
Unknown
Unknown
Unknown
Unknown
The Endpoint 0 buffer is comprised of 8 bytes located at address 0x50 to 0x57
Table 21-6. Endpoint 1 Data (EP1DATA) [0x58-0x5F] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Endpoint 1 Data Buffer [7:0]
Read/Write
Default
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Unknown
Unknown
Unknown
Unknown
Unknown
Unknown
Unknown
Unknown
The Endpoint 1buffer is comprised of 8 bytes located at address 0x58 to 0x5F
Table 21-7. Endpoint 2 Data (EP2DATA) [0x60-0x67] [R/W]
Bit #
Field
7
6
5
4
3
2
1
0
Endpoint 2 Data Buffer [7:0]
Read/Write
Default
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Unknown
Unknown
Unknown
Unknown
Unknown
Unknown
Unknown
Unknown
The Endpoint 2 buffer is comprised of 8 bytes located at address 0x60 to 0x67
The three data buffers used to hold data for both IN and OUT
transactions. Each data buffer is 8 bytes long.
Unlike past enCoRe parts the USB data buffers are only
accessible in the I/O space of the processor.
The reset values of the Endpoint Data Registers are unknown.
Document 38-08035 Rev. *F
Page 50 of 68
CY7C63310
CY7C638xx
CY7C639xx
22.0
USB Mode Tables
Mode
DISABLE
Encoding
SETUP
IN
OUT
Comments
0000
Ignore
Ignore
Ignore
Ignore all USB traffic to this endpoint. Used by Data and
Control endpoints
NAK IN/OUT
STATUS OUT ONLY
STALL IN/OUT
0001
0010
0011
0110
Accept
Accept
Accept
Accept
NAK
STALL
STALL
TX0 byte
NAK
NAK IN and OUT token. Control endpoint only
STALL IN and ACK zero byte OUT. Control endpoint only
STALL IN and OUT token. Control endpoint only
Check
STALL
STALL
STATUS IN ONLY
STALL OUT and send zero byte data for IN token. Con-
trol endpoint only
ACK OUT – STATUS
IN
1011
1111
Accept
Accept
TX0 byte
TX Count
ACK
ACK the OUT token or send zero byte data for IN token.
Control endpoint only
ACK IN – STATUS
OUT
Check
Respond to IN data or Status OUT. Control endpoint only
NAK OUT
1000
1001
Ignore
Ignore
Ignore
Ignore
NAK
ACK
Send NAK handshake to OUT token. Data endpoint only
ACK OUT (STALL = 0)
This mode is changed by the SIE to mode 1000 on is-
suance of ACK handshake to an OUT. Data endpoint
only
ACK OUT (STALL = 1)
NAK IN
1001
1100
1101
Ignore
Ignore
Ignore
Ignore
NAK
STALL
Ignore
Ignore
STALL the OUT transfer
Send NAK handshake for IN token. Data endpoint only
ACK IN (STALL = 0)
TX Count
This mode is changed by the SIE to mode 1100 after
receiving ACK handshake to an IN data. Data endpoint
only
ACK IN (STALL = 1)
1101
Ignore
STALL
Ignore
STALL the IN transfer. Data endpoint only
Reserved
Reserved
Reserved
Reserved
Reserved
0101
0111
1010
0100
1110
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
Ignore
These modes are not supported by SIE. Firmware
should not use this mode in Control and Data endpoints
Mode Column
SETUP, IN, and OUT Columns
The 'Mode' column contains the mnemonic names given to the
modes of the endpoint. The mode of the endpoint is deter-
mined by the four-bit binaries in the 'Encoding' column as
discussed below. The Status IN and Status OUT represent the
status IN or OUT stage of the control transfer.
Depending on the mode specified in the 'Encoding' column,
the 'SETUP', 'IN', and 'OUT' columns contain the SIE's
responses when the endpoint receives SETUP, IN, and OUT
tokens, respectively.
A 'Check' in the Out column means that upon receiving an
OUT token the SIE checks to see whether the OUT is of zero
length and has a Data Toggle (Data1/0) of 1. If these condi-
tions are true, the SIE responds with an ACK. If any of the
above conditions is not met, the SIE will respond with either a
STALL or Ignore.
Encoding Column
The contents of the 'Encoding' column represent the Mode Bits
[3:0] of the Endpoint Mode Registers (Table 21-3 and
Table 21-4). The endpoint modes determine how the SIE
responds to different tokens that the host sends to the
endpoints. For example, if the Mode Bits [3:0] of the Endpoint
0 Mode Register are set to '0001', which is NAK IN/OUT mode,
the SIE will send an ACK handshake in response to SETUP
tokens and NAK any IN or OUT tokens.
A 'TX Count' entry in the IN column means that the SIE will
transmit the number of bytes specified in the Byte Count Bit
[3:0] of the Endpoint Count Register (Table 21-2) in response
to any IN token.
Document 38-08035 Rev. *F
Page 51 of 68
CY7C63310
CY7C638xx
CY7C639xx
23.0
Details of Mode for Differing Traffic Conditions
Control Endpoint
SIE
Bus Event
SIE
EP0 Mode Register
EP0 Count Register
EP0 Interrupt Comments
Mode Token
DISABLED
Count
Dval
D0/1 Response S
I
O
A
MODE DTOG DVAL COUNT FIFO
0000
x
x
x
x
Ignore All
STALL_IN_OUT
0011 SETUP
0011 SETUP
0011 SETUP
>10
<=10
<=10
x
x
invalid
valid
x
x
x
junk
junk
Ignore
Ignore
x
x
x
x
x
ACK
1
1
1
1
0001 update
1
1
1
update data
Yes
ACK SETUP
Stall IN
0011
0011
0011
0011
IN
STALL
OUT
OUT
OUT
>10
x
Ignore
<=10
<=10
invalid
valid
Ignore
STALL
Stall OUT
NAK_IN_OUT
0001 SETUP
0001 SETUP
0001 SETUP
>10
<=10
<=10
x
x
invalid
valid
x
x
x
x
x
x
x
x
junk
junk
Ignore
Ignore
ACK
NAK
1
0001 update
update data
Yes
ACK SETUP
NAK IN
Ignore
0001
0001
0001
0001
IN
OUT
OUT
OUT
>10
x
<=10
<=10
invalid
valid
Ignore
NAK
NAK OUT
ACK_IN_STATUS_OUT
1111 SETUP
1111 SETUP
1111 SETUP
>10
<=10
<=10
x
x
invalid
valid
x
x
x
x
x
x
x
x
x
0
1
junk
junk
Ignore
Ignore
ACK
TX
1
1
0001 update
0001
update data
Yes
Yes
ACK SETUP
Host Not ACK'd
Host ACK'd
Ignore
1111
1111
1111
1111
1111
1111
1111
IN
IN
x
x
TX
1
OUT
OUT
>10
<=10
x
invalid
Ignore
OUT <=10, <>2 valid
STALL
STALL
ACK
0011
0011
Yes
Yes
Yes
Bad Status
Bad Status
Good Status
OUT
OUT
2
2
valid
valid
1
1
1
0010
1
1
1
2
STATUS_OUT
0010 SETUP
0010 SETUP
0010 SETUP
>10
<=10
<=10
x
x
invalid
valid
x
x
x
x
x
x
x
x
0
1
junk
junk
Ignore
Ignore
ACK
1
0001 update
0011
update data
Yes
Yes
ACK SETUP
Stall IN
0010
0010
0010
0010
0010
0010
IN
STALL
OUT
OUT
>10
<=10
x
Ignore
invalid
Ignore
OUT <=10, <>2 valid
STALL
STALL
ACK
0011
0011
1
Yes
Yes
Yes
Bad Status
Bad Status
Good Status
OUT
OUT
2
2
valid
valid
1
1
1
1
2
ACK_OUT_STATUS_IN
1011 SETUP
1011 SETUP
1011 SETUP
>10
<=10
<=10
x
x
invalid
valid
x
x
x
x
x
x
junk
junk
Ignore
Ignore
ACK
TX 0
TX 0
1
1
1
0001 update
0011
update data
Yes
Yes
ACK SETUP
Host Not ACK'd
Host ACK'd
1011
1011
IN
IN
x
x
1
Document 38-08035 Rev. *F
Page 52 of 68
CY7C63310
CY7C638xx
CY7C639xx
23.0
Details of Mode for Differing Traffic Conditions (continued)
1011
1011
1011
OUT
OUT
OUT
>10
<=10
<=10
x
x
x
x
junk
junk
Ignore
Ignore
invalid
valid
ACK
1
1
0001 update
1
1
update data
Yes
Good OUT
STATUS_IN
0110 SETUP
0110 SETUP
0110 SETUP
>10
<=10
<=10
x
x
invalid
valid
x
x
x
x
x
x
x
x
x
junk
junk
Ignore
Ignore
ACK
TX 0
TX 0
1
1
1
0001 update
0011
update data
Yes
Yes
ACK SETUP
Host Not ACK'd
Host ACK'd
Ignore
0110
0110
0110
0110
0110
IN
IN
x
x
1
OUT
OUT
OUT
>10
<=10
<=10
x
invalid
valid
Ignore
STALL
0011
Yes
Stall OUT
Data Out Endpoints
SIE
Bus Event
SIE
EP0 Mode Register
EP0 Count Register
EP0 Interrupt Comments
Mode Token
Count
Dval
D0/1 Response S
I
O
A
MODE DTOG DVAL COUNT FIFO
ACK OUT (STALL Bit = 0)
1001
1001
1001
1001
IN
x
x
x
x
x
Ignore
OUT
OUT
OUT
>MAX
junk
junk
Ignore
<=MAX invalid invalid
Ignore
<=MAX
valid
valid
ACK
1
1000 update
1
update data
Yes
ACK OUT
ACK OUT (STALL Bit = 1)
1001
1001
1001
1001
IN
x
x
x
x
x
Ignore
OUT
OUT
OUT
>MAX
Ignore
<=MAX invalid invalid
Ignore
<=MAX
valid
valid
STALL
Stall OUT
NAK OUT
1000
IN
x
x
x
x
x
Ignore
Ignore
Ignore
1000
1000
1000
OUT
OUT
OUT
>MAX
<=MAX invalid invalid
<=MAX
valid
valid
NAK
If Enabled NAK OUT
Data In Endpoints
SIE
Bus Event
SIE
EP0 Mode Register
EP0 Count Register
EP0 Interrupt Comments
Mode Token
Count
Dval
D0/1 Response S
I
O
A
MODE DTOG DVAL COUNT FIFO
ACK IN (STALL Bit = 0)
1101
1101
1101
OUT
IN
x
x
x
x
x
x
x
x
Ignore
Host Not ACK'd
Host ACK'd
IN
x
TX
1
1100
Yes
ACK IN (STALL Bit = 1)
1101
1101
OUT
IN
x
x
x
x
x
x
Ignore
STALL
NAK
Stall IN
NAK IN
1100
OUT
IN
x
x
x
x
x
x
Ignore
1100
If Enabled NAK IN
Document 38-08035 Rev. *F
Page 53 of 68
CY7C63310
CY7C638xx
CY7C639xx
24.0
Register Summary
Addr
Name
7
6
5
4
3
2
1
0
R/W
Default
00
P0DATA
P0.7
P0.6/TIO1 P0.5/TIO0 P0.4/INT2 P0.3/INT1 P0.2/INT0 P0.1/CLK- P0.0/CLKI
bbbbbbbb
00000000
OUT
N
01
P1DATA
P1.7
P1.6/SMI P1.5/SMO P1.4/SCLK P1.3/SSEL P1.2/VREG
P1.1/D–
P1.0/D+
bbbbbbbb
00000000
SO
SI
02
03
04
05
P2DATA
P3DATA
P4DATA
P00CR
P2.7–P2.2
P3.7–P3.2
P2.1–P2.0
P3.1–P3.0
bbbbbbbb
bbbbbbbb
----bbbb
00000000
00000000
00000000
00000000
Res
P4.3–P4.0
Reserved
Int
Enable
Int Act TTL Thresh High Sink Open Drain
Low
Pull-up
Output
Enable
-bbbbbbb
Enable
06
07–09
0A–0B
0C
P01CR
CLK
Int
Int Act TTL Thresh High Sink Open Drain
Low
Pull-up
Enable
Output
Enable
bbbbbbbb
--bbbbbb
bbbbbbbb
-bbbbbbb
-bb---bb
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
Output
Enable
P02CR–
P04CR
Reserved Reserved
Int Act TTL Thresh Reserved Open Drain
Low
Pull-up
Enable
Output
Enable
P05CR–
P06CR
TIO
Output
Int
Enable
Int Act TTL Thresh Reserved Open Drain
Low
Pull-up
Enable
Output
Enable
P07CR
P10CR
P11CR
P12CR
P13CR
Reserved
Reserved
Reserved
Int
Enable
Int Act TTL Thresh Reserved Open Drain
Low
Pull-up
Enable
Output
Enable
0D
Int
Enable
Int Act
Low
Reserved
PS/2 Pull-
up Enable
Output
Enable
0E
Int
Enable
Int Act
Low
Reserved
Open Drain Reserved
Output
Enable
-bb--b-b
0F
CLK
Output
Int
Enable
Int Act TTL Thresh Reserved Open Drain
Low
Pull-up
Enable
Output
Enable
bbbbbbbb
-bbbbbbb
bbbbbbbb
-bbbbbbb
-bbbbbbb
-bbbbbbb
-bbb-bbb
10
Reserved
Int
Enable
Int Act
Low
3.3V Drive High Sink Open Drain
Pull-up
Enable
Output
Enable
11–13
14
P14CR–
P16CR
SPI Use
Int
Enable
Int Act
Low
3.3V Drive High Sink Open Drain
Pull-up
Enable
Output
Enable
P17CR
P2CR
P3CR
P4CR
Reserved
Reserved
Reserved
Int
Enable
Int Act TTL Thresh High Sink Open Drain
Low
Pull-up
Enable
Output
Enable
15
Int
Enable
Int Act TTL Thresh High Sink Open Drain
Low
Pull-up
Enable
Output
Enable
16
Int
Enable
Int Act TTL Thresh High Sink Open Drain
Low
Pull-up
Enable
Output
Enable
17
Reserved Int Enable Int Act TTL Thresh Reserved Open Drain
Low
Pull-up
Enable
Output
Enable
20
21
22
23
24
25
26
27
28
29
2A
FRTMRL
FRTMRH
TCAP0R
TCAP1R
TCAP0F
TCAP1F
PITMRL
PITMRH
PIRL
Free Running Timer [7:0]
Free Running Timer [15:8]
Capture 0 Rising [7:0]
Capture 1 Rising [7:0]
Capture 0 Falling [7:0]
Capture 1 Falling [7:0]
Prog Interval Timer [7:0]
bbbbbbbb
bbbbbbbb
bbbbbbbb
bbbbbbbb
bbbbbbbb
bbbbbbbb
bbbbbbbb
----bbbb
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
Reserved
Prog Interval Timer [11:8]
Prog Interval [7:0]
bbbbbbbb
----bbbb
PIRH
Reserved
Prog Interval [11:8]
Reserved
TMRCR
First Edge
Hold
8-bit capture Prescale
Cap0 16bit
Enable
bbbbb---
2B
2C
30
TCAPINTE
TCAPINTS
Reserved
Reserved
Cap1 Fall
Active
Cap1 Rise Cap0 Fall Cap0 Rise
Active Active Active
----bbbb
----bbbb
-bb----b
00000000
00000000
00010000
Cap1 Fall
Active
Cap1 Rise Cap0 Fall Cap0 Rise
Active
Active
Active
CPUCLKCR Reserved USB CLK USB CLK
Reserved
CPU
CLK Select
/2 Disable
TCAPCLK Divider
Reserved
Select
31
32
ITMRCLKCR
CLKIOCR
TCAPCLK Select
ITMRCLK Divider
ITMRCLK Select
CLKOUT Select
bbbbbbbb
---bbbbb
10001111
00000000
XOSC
Select
XOSC
Enable
EFTB
Disable
34
35
36
IOSCTR
XOSCTR
LPOSCTR
foffset[2:0]
Reserved
Gain[4:0]
bbbbbbbb
---bbb-b
000ddddd
000ddd0d
dddddddd
XOSC XGM [2:0]
Reserved
Mode
32-KHz Reserved 32-KHz Bias Trim [1:0]
32-KHz Freq Trim [3:0]
b-bbbbbb
Low
Power
Document 38-08035 Rev. *F
Page 54 of 68
CY7C63310
CY7C638xx
CY7C639xx
24.0
Register Summary (continued)
Addr
Name
7
6
5
4
3
2
1
0
R/W
Default
39
OSCLCKCR
Reserved
Fine Tune
Only
USB
Osclock
Disable
------bb
00000000
3C
3D
40
SPIDATA
SPICR
SPIData[7:0]
CPOL
bbbbbbbb
bbbbbbbb
bbbbbbbb
00000000
00000000
00000000
Swap
LSB First
Comm Mode
CPHA
SCLK Select
USBCR
USB
Enable
Device Address[6:0]
41
42
43
44
45
46
EP0CNT
EP1CNT
Data
Data Valid
Data Valid
Data Valid
Reserved
Reserved
Reserved
Byte Count[3:0]
bbbbbbbb
bbbbbbbb
bbbbbbbb
ccccbbbb
b-bcbbbb
b-bcbbbb
00000000
00000000
00000000
00000000
00000000
00000000
Toggle
Data
Toggle
Byte Count[3:0]
Byte Count[3:0]
Mode[3:0]
EP2CNT
Data
Toggle
EP0MODE
EP1MODE
EP2MODE
Setup
rcv’d
IN rcv’d OUT rcv’d ACK’d trans
Stall
Reserved NAK Int Ack’d trans
Enable
Mode[3:0]
Stall
Reserved NAK Int Ack’d trans
Enable
Mode[3:0]
50–57
58–5F
60–67
73
EP0DATA
EP1DATA
EP2DATA
VREGCR
Endpoint 0 Data Buffer [7:0]
bbbbbbbb
bbbbbbbb
bbbbbbbb
------bb
????????
????????
????????
00000000
Endpoint 1 Data Buffer [7:0]
Endpoint 2 Data Buffer [7:0]
Reserved
Keep Alive
VREG
Enable
74
DA
DB
USBXCR
USB Pull-
up Enable
Reserved
USB Force
State
b------b
00000000
00000000
00000000
INT_CLR0 GPIOPort
1
Sleep
Timer
INT1
GPIO Port
SPI
SPI Transmit
INT0
POR/LVD
bbbbbbbb
bbbbbbbb
0
Receive
INT_CLR1
TCAP0
Prog
Interval
Timer
1-ms
Timer
USB Active USB Reset USB EP2
USB EP1 USB EP0
DC
INT_CLR2 Reserved GPIO Port GPIOPort GPIO Port 2 PS/2 Data
INT2
16-bit
Counter
Wrap
TCAP1
-bbbbbbb
00000000
4
3
Low
DE
DF
INT_MSK3 ENSWINT
Reserved
b-------
00000000
00000000
INT_MSK2 Reserved GPIO Port GPIOPort GPIO Port 2 PS/2 Data
INT2
Int Enable
16-bit
TCAP1
-bbbbbbb
4
3
Int Enable
Low Int
Enable
Counter Int Enable
Wrap
Int Enable Int Enable
Int Enable
E1
E0
INT_MSK1
TCAP0
Prog
1-ms
Timer
USB Active USB Reset USB EP2
USB EP1 USB EP0
bbbbbbbb
bbbbbbbb
00000000
00000000
Int Enable Interval
Timer
Int Enable Int Enable Int Enable Int Enable Int Enable
Int Enable
Int Enable
INT_MSK0 GPIOPort
1
Sleep
Timer
INT1
GPIOPort0
SPI
Receive
Int Enable
SPI Transmit
Int Enable Int Enable Int Enable
INT0
POR/ LVD
Int Enable Int Enable
Int Enable Int Enable
E2
E3
--
INT_VC
RESWDT
CPU_A
Pending Interrupt [7:0]
Reset Watchdog Timer [7:0]
Temporary Register T1 [7:0]
X[7:0]
bbbbbbbb
wwwwwwww
--------
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000010
00010000
00000000
00000000
00000000
00000000
--
CPU_X
--------
--
CPU_PCL
CPU_PCH
CPU_SP
CPU_F
Program Counter [7:0]
Program Counter [15:8]
Stack Pointer [7:0]
--------
--
--------
--
--------
-
Reserved
Reserved WDRS
Reserved No Buzz
PORLEV[1:0]
XOI
Super
Sleep
Carry
Zero
Global IE
Stop
---brwww
r-ccb--b
--bbbbbb
--bb-bbbb
bb------
FF
1E0
1E3
1EB
1E4
CPU_SCR
OSC_CR0
LVDCR
GIES
PORS
Reserved
Reserved
Sleep Timer [1:0]
Reserved
Reserved
CPU Speed [2:0]
VM[2:0]
Reserved
ECO_TR
VLTCMP
Sleep Duty Cycle [1:0]
Reserved
LVD
PPOR
------rr
Note: In the R/W column,
b = Both Read and Write
r = Read Only
w = Write Only
c = Read/Clear
? = Unknown
d = calibration value. Should not change during normal use
Document 38-08035 Rev. *F
Page 55 of 68
CY7C63310
CY7C638xx
CY7C639xx
Maximum Total Sink Output Current into Port 0
and 1 and Pins............................................................. 70 mA
25.0
Absolute Maximum Ratings
Storage Temperature .................................–65°C to +150°C
Ambient Temperature with Power Applied..... –0°C to +70°C
Supply Voltage on V Relative to V ......... –0.5V to +7.0V
Maximum Total Source Output Current into GPIO Pins30 mA
Maximum On-chip Power Dissipation
on any GPIO Pin......................................................... 50 mW
CC
SS
DC Input Voltage.................................–0.5V to + V + 0.5V
Power Dissipation .................................................... 300 mW
Static Discharge Voltage ............................................. 2200V
Latch-up Current ...................................................... 200 mA
CC
DC Voltage Applied to Outputs in
High-Z State....................................... –0.5V to + V + 0.5V
CC
26.0
DC Characteristics
Description
General
Operating Voltage
Parameter
Conditions
Min.
4.0
Typical Max.
Unit
V
V
No USB activity, CPU speed < 12 MHz
5.25
5.25
CC1
CC2
V
Operating Voltage
USB activity, CPU speed < 12 MHz.
Flash programming
4.35
V
V
Operating Voltage
Operating Temp
USB activity, CPU speed < 24 MHz
Flash Programming
4.75
0
5.25
70
V
CC3
FP
T
°C
mA
I
V
Operating Supply Current
V = 5.25V, no GPIO loading,
CC
24 MHz
40
CC1
CC
I
I
V
Operating Supply Current
V
= 5.0V, no GPIO loading, 6 MHz
10
mA
CC2
CC
CC
Standby Current
Internal and External Oscillators,
Bandgap, Flash, CPU Clock, Timer
Clock, USB Clock all disabled
10
µA
SB1
Low-voltage Detect
V
Low-voltage detect Trip Voltage
(8 programmable trip points)
2.681
4.872
V
LVD
3.3V Regulator
I
I
Max Regulator Output Current
V
> 4.35V
CC
125
20
mA
VREG
FA
[5]
Keep Alive Current
When regulator is disabled with
“keep alive” enable
µA
V
V
V
Output Voltage
Output Voltage
V
VREG
> 4.35V, 0 < temp < 40°C,
3.0
3.6
V
V
REG1
REG
REG
CC
I
< 125 mA (3.3V ± 8%)
V
V
> 4.35V, 0 < temp < 40°C,
< 25 mA (3.3V ± 4%)
3.15
3.45
REG2
CC
I
VREG
USB Interface
V
V
V
V
Static Output High
15K ± 5% Ohm to V
2.8
3.6
0.3
V
V
V
V
ON
OFF
DI
SS
Static Output Low
R
is enabled
UP
Differential Input Sensitivity
0.2
0.8
Differential Input Common Mode
Range
2.5
CM
V
Single Ended Receiver Threshold
Transceiver Capacitance
0.8
2
V
SE
C
I
20
10
pF
µA
IN
Hi-Z State Data Line Leakage
0V < V < 3.3V
–10
IO
IN
PS/2 Interface
V
Static Output Low
SDATA or SCLK pins
0.4
7
V
OLP
R
Internal PS/2 Pull-up Resistance
SDATA, SCLK pins, PS/2 Enabled
3
KΩ
PS2
Notes:
5. Keep-alive mode regulator output voltage min. 2.35V, max 3.80V
Document 38-08035 Rev. *F
Page 56 of 68
CY7C63310
CY7C638xx
CY7C639xx
26.0
DC Characteristics (continued)
Description
Parameter
General
Conditions
Min.
Typical Max.
Unit
General Purpose I/O Interface
R
Pull-up Resistance
4
12
KΩ
UP
V
Input Threshold Voltage Low, CMOS Low to High edge
mode
40%
65%
V
V
V
ICR
CC
CC
CC
V
Input Threshold Voltage Low, CMOS High to Low edge
mode
30%
3%
55%
ICF
V
V
V
V
V
V
V
Input Hysteresis Voltage, CMOS Mode High to low edge
10%
0.8
HC
Input Low Voltage, TTL Mode
Input High Voltage, TTL Mode
Output Low Voltage, High Drive
Output Low Voltage, High Drive
I/O-pin Supply = 2.9–3.6V
I/O-pin Supply = 4.0–5.5V
V
V
V
V
V
V
ILTTL
IHTTL
OL1
OL2
OL3
OH
2.0
[6]
[6]
I
I
I
I
= 50 mA
= 25 mA
= 8 mA
0.8
0.4
0.4
OL1
OL1
OL2
OH
[7]
Output Low Voltage, Low Drive
[7]
Output High Voltage
= 2 mA
V
–
CC
0.5
27.0
AC Characteristics
Parameter
Clock
Description
Conditions
Min.
Typical Max.
Unit
T
External Clock Duty Cycle
45
55
24
%
ECLKDC
T
T
External Clock Frequency
External Clock Frequency
External clock is the source of the
CPUCLK
0.187
MHz
ECLK1
ECLK2
External clock is not the source of the
CPUCLK
0
24
MHz
USB Driver
T
T
T
T
T
Transition Rise Time
Transition Rise Time
Transition Fall Time
Transition Fall Time
Rise/Fall Time Matching
C
C
C
C
= 200 pF
= 600 pF
= 200 pF
= 600 pF
75
75
ns
ns
ns
ns
%
V
R1
R2
F1
F2
R
LOAD
LOAD
LOAD
LOAD
300
300
125
2.0
80
V Output Signal Crossover Voltage
USB Data Timing
1.3
CRS
T
T
T
T
T
T
T
T
T
T
Low-speed Data Rate
Ave. Bit Rate (1.5 Mbps ± 1.5%)
To next transition
1.4775
–75
1.5225 Mbps
DRATE
DJR1
DJR2
DEOP
EOPR1
EOPR2
EOPT
UDJ1
UDJ2
LST
Receiver Data Jitter Tolerance
Receiver Data Jitter Tolerance
Differential to EOP Transition Skew
EOP Width at Receiver
75
45
ns
ns
ns
ns
ns
us
ns
ns
ns
To pair transition
–45
–40
100
330
Rejects as EOP
Accept as EOP
EOP Width at Receiver
675
1.25
–95
–95
Source EOP Width
1.5
95
Differential Driver Jitter
To next transition
To pair transition
Differential Driver Jitter
95
Width of SE0 during Diff. Transition
210
Notes:
6. Available only on CY7C639XX P2.7, P3.7, P0.0, P0.1; CY7C638XX P1.3, P1.4, P1.5, P1.6, P1.7.
7. Except for pins P1.0, P1.1 in GPIO mode.
Document 38-08035 Rev. *F
Page 57 of 68
CY7C63310
CY7C638xx
CY7C639xx
27.0
AC Characteristics (continued)
Parameter
Description
Conditions
Min.
Typical Max.
Unit
Non-USB Mode Driver Characteristics
T
SDATA/SCK Transition Fall Time
50
300
ns
FPS2
SPI Timing
T
T
T
T
T
T
SPI Master Clock Rate
SPI Slave Clock Rate
SPI Clock High Time
SPI Clock Low Time
F
/6
2
MHz
MHz
ns
SMCK
SSCK
SCKH
SCKL
MDO
CPUCLK
2.2
High for CPOL = 0, Low for CPOL = 1
Low for CPOL = 0, High for CPOL = 1
SCK to data valid
125
125
–25
100
ns
[8]
Master Data Output Time
50
ns
Master Data Output Time,
First bit with CPHA = 0
Time before leading SCK edge
ns
MDO1
T
T
T
T
T
T
Master Input Data Set-up time
Master Input Data Hold time
Slave Input Data Set-up Time
Slave Input Data Hold Time
Slave Data Output Time
50
50
50
50
ns
ns
ns
ns
ns
ns
MSU
MHD
SSU
SHD
SDO
SDO1
SCK to data valid
100
100
Slave Data Output Time,
First bit with CPHA = 0
Time after SS LOW to data valid
T
T
Slave Select Set-up Time
Slave Select Hold Time
Before first SCK edge
After last SCK edge
150
150
ns
ns
SSS
SSH
T
CYC
T
CH
CLOCK
T
CL
Figure 27-1. Clock Timing
T
T
F
R
D+
D−
V
oh
90%
90%
V
crs
10%
10%
V
ol
Figure 27-2. USB Data Signal Timing
Note:
8. In Master mode first bit is available 0.5 SPICLK cycle before Master clock edge available on the SCLK pin.
Document 38-08035 Rev. *F
Page 58 of 68
CY7C63310
CY7C638xx
CY7C639xx
T
PERIOD
Differential
DataLine
T
JR
T
JR1
T
JR2
Consecutive
Transitions
N*T +T
PERIOD
JR1
Paired
Transitions
N*T +T
PERIOD
JR2
Figure 27-3. Receiver Jitter Tolerance
Figure 27-4. Differential to EOP Transition Skew and EOP Width
T
PERIOD
Crossover
Points
Differenti l
DataLine
Consecutive
Transitions
N*T +T
PERIOD xJR1
Paired
Transitions
N*T +T
PERIOD xJR2
Figure 27-5. Differential Data Jitter
Document 38-08035 Rev. *F
Page 59 of 68
CY7C63310
CY7C638xx
CY7C639xx
(SS is under firmware control in SPI Master mode)
SS
T
SCKL
SCK (CPOL=0)
T
SCKH
SCK (CPOL=1)
MOSI
T
MDO
MSB
LSB
MSB
LSB
MISO
T
T
MHD
MSU
Figure 27-6. SPI Master Timing, CPHA = 1
SS
T
T
SSH
SSS
T
SCKL
SCK (CPOL=0)
T
SCKH
SCK (CPOL=1)
MOSI
MSB
LSB
T
T
SHD
T
SSU
SDO
MSB
LSB
MISO
Figure 27-7. SPI Slave Timing, CPHA = 1
Document 38-08035 Rev. *F
Page 60 of 68
CY7C63310
CY7C638xx
CY7C639xx
(SS is under firmware control in SPI Master mode)
SS
T
SCKL
SCK (CPOL=0)
SCK (CPOL=1)
T
SCKH
T
MDO
T
MDO1
MSB
LSB
MOSI
MISO
MSB
LSB
T
T
MSU MHD
Figure 27-8. SPI Master Timing, CPHA = 0
SS
T
T
SSH
SSS
T
SCKL
SCK (CPOL=0)
T
SCKH
SCK (CPOL=1)
MOSI
MSB
LSB
T
T
SHD
SSU
T
SDO
T
SDO1
MISO
MSB
LSB
Figure 27-9. SPI Slave Timing, CPHA = 0
Document 38-08035 Rev. *F
Page 61 of 68
CY7C63310
CY7C638xx
CY7C639xx
28.0
Ordering Information
Ordering Code
FLASH Size
RAM Size
256
Package Type
CY7C63923-PVXC
CY7C63913-PXC
CY7C63903-PVXC
CY7C63923-XWC
CY7C63823-PXC
CY7C63823-SXC
CY7C63823-QXC
CY7C63813-PXC
CY7C63813-SXC
CY7C63803-SXC
CY7C63801-PXC
CY7C63801-SXC
CY7C63310-PXC
CY7C63310-SXC
8K
8K
8K
8K
8K
8K
8K
8K
8K
8K
4K
4K
3K
3K
48-SSOP
40-PDIP
28-SSOP
Die
256
256
256
256
24-PDIP
24-SOIC
24-QSOP
18-PDIP
18-SOIC
16-SOIC
16-PDIP
16-SOIC
16-PDIP
16-SOIC
256
256
256
256
256
256
256
128
128
29.0
Package Diagrams
16-Lead (300-Mil) Molded DIP P1
51-85009-*A
Document 38-08035 Rev. *F
Page 62 of 68
CY7C63310
CY7C638xx
CY7C639xx
29.0
Package Diagrams (continued)
16 Lead (150 Mil) SOIC
16-Lead (150-Mil) SOIC S16.15
PIN 1 ID
8
1
DIMENSIONS IN INCHES[MM] MIN.
MAX.
REFERENCE JEDEC MS-012
PACKAGE WEIGHT 0.15gms
0.150[3.810]
0.157[3.987]
0.230[5.842]
0.244[6.197]
9
16
0.010[0.254]
0.016[0.406]
X 45°
0.386[9.804]
0.393[9.982]
SEATING PLANE
0.061[1.549]
0.068[1.727]
0.004[0.102]
0.050[1.270]
BSC
0.0075[0.190]
0.0098[0.249]
0.016[0.406]
0.035[0.889]
0°~8°
0.0138[0.350]
0.0192[0.487]
0.004[0.102]
0.0098[0.249]
51-85068-*B
18-Lead (300-Mil) Molded DIP P3
51-85010-*A
Document 38-08035 Rev. *F
Page 63 of 68
CY7C63310
CY7C638xx
CY7C639xx
29.0
Package Diagrams (continued)
18-Lead (300-Mil) Molded SOIC S3
PIN 1 ID
9
1
MIN.
MAX.
DIMENSIONS IN INCHES[MM]
REFERENCE JEDEC MO-119
0.291[7.391]
0.300[7.620]
*
0.394[10.007]
0.419[10.642]
10
18
0.026[0.660]
0.032[0.812]
SEATING PLANE
0.447[11.353]
0.463[11.760]
0.092[2.336]
0.105[2.667]
*
0.0091[0.231]
0.0125[0.317]
0.004[0.101]
*
0.050[1.270]
TYP.
0.004[0.101]
0.0118[0.299]
0.015[0.381]
0.050[1.270]
0.013[0.330]
0.019[0.482]
51-85023-*B
24-Lead (300-Mil) SOIC S13
PIN 1 ID
12
1
MIN.
DIMENSIONS IN INCHES[MM]
MAX.
*
0.394[10.007]
0.419[10.642]
REFERENCE JEDEC MO-119
PACKAGE WEIGHT 0.65gms
0.291[7.391]
0.300[7.620]
13
24
0.026[0.660]
0.032[0.812]
SEATING PLANE
0.597[15.163]
0.615[15.621]
0.092[2.336]
0.105[2.667]
*
0.004[0.101]
0.0091[0.231]
0.0125[0.317]
*
0.050[1.270]
TYP.
0.015[0.381]
0.050[1.270]
0.004[0.101]
0.0118[0.299]
0.013[0.330]
0.019[0.482]
51-85025-*B
Document 38-08035 Rev. *F
Page 64 of 68
CY7C63310
CY7C638xx
CY7C639xx
29.0
Package Diagrams (continued)
24-Lead (300-Mil) PDIP P13
51-85013-*B
24-lead QSOP O241
0.033
REF.
PIN 1 ID
12
1
0.150
0.157
0.228
DIMENSIONS IN INCHES MIN.
MAX.
0.244
13
24
0.337
0.344
SEATING
PLANE
0.007
0.010
0.053
0.069
0.004
0.008
0.012
0°-8°
0.004
0.010
0.016
0.034
0.025
BSC.
51-85055-*B
Document 38-08035 Rev. *F
Page 65 of 68
CY7C63310
CY7C638xx
CY7C639xx
29.0
Package Diagrams (continued)
28-Lead (5.3 mm) Shrunk Small Outline Package O28
51-85079-*C
40-Lead (600-Mil) Molded DIP P17
51-85019-*A
Document 38-08035 Rev. *F
Page 66 of 68
CY7C63310
CY7C638xx
CY7C639xx
29.0
Package Diagrams (continued)
48-Lead Shrunk Small Outline Package O48
51-85061-*C
PSoC is a trademark of Cypress MicroSystems. enCoRe is a trademark of Cypress Semiconductor Corporation. All product and
company names mentioned in this document are the trademarks of their respective holders.
Document 38-08035 Rev. *F
Page 67 of 68
© Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
CY7C63310
CY7C638xx
CY7C639xx
Document History Page
Document Title: CY7C63310/CY7C638xx/CY7C639xx enCoRe™ II Low-Speed USB Peripheral Controller
Document Number: 38-08035
Orig. of
Rev.
**
ECN No. Issue Date Change
Description of Change
131323
221881
12/11/03
See ECN
XGR
KKU
New data sheet
*A
Added Register descriptions and package information, changed from advance
information to preliminary
*B
*C
271232
299179
See ECN
See ECN
BON
BON
Reformatted
Updated with the latest information
Corrected 24-PDIP pinout typo in Table 5.1 Added Table 10-1.
Updated Table 9-5, Table 10-4, Table 13-1, Table 17-2, Table 17-4, Table 17-6.
and Table 15-2. Added various updates to the GPIO Section (Section 14.0).
Corrected Table 15-3. Corrected Figure 27-6 and Figure 27-7. Added the 16-pin
PDIP package diagram (Section 29.0).
*D
322053
See ECN
TVR
Introduction section: Last para removed Low-voltage reset. There is no LVR
there is only LVD (Low voltage detect). explained more about LVD and POR.
Changed capture pins from P0.0,P0.1 to P0.5,P0.6.
Table 6-1: Changed table heading (Removed Mnemonics and made as Register
names). Table 9-5: Included #of rows for different flash sizes
Section10-1: Changed CPUCLK selectable options from n=0-5,7,8 to n=0-5,7.
Clocks section: Changed ITMRCLK division to 1,2,3,4. updated the sources to
ITMRCLK, TCAPCLKs. Mentioned P17 is TTL enabled permanently. Corrected
FRT, PIT data write order. Updated INTCLR,INTMSK registers. in the register
table also. DC spec sheet: changed LVR to LVD included max min program-
mable trip points based on char data. Updated the 50ma sink pins on 638xx,
639xx. Keep-alive voltage mentioned corresponding to Keep-alive current of
20uA. Included Notes regarding VOL,VOH on P1.0,P1.1 and TMDO spec. AC
Specs: T
, T
In description column changed Phase to 0.
MDO1 SDO1
BON
Section 5: Removed the VREG from the CY7C63310 and CY7C63801.
Removed SCLK and SDATA. Created a separate pinout diagram for the
CY7C63813.
Added the GPIO Block Diagram (Figure 14-1.)
Table 10-5: Changed the Sleep Timer Clock unit from 32 KHz count to Hz
Table 21-1: Added more descriptions to the register
*E
*F
341277
408017
See ECN
See ECN
BHA
TYJ
Corrected V TTL value in DC Characteristics table
IH
Updated V TTL value.
IL
Added footnote to pin description table for D+/D- pins.
Added Typical Values to Low Voltage Detect table.
Corrected Pin label on 16-pin PDIP package.
Corrected minor typos
Corrected pin assignment for the 24-pin QSOP package - GPIO port 3 in Table
5-1: Pin Assignment
New Assignments: Pin 19 assigned to P3.0 and pin 20 to P3.1
Table 17.7 INT_MSK1 changed to 0xE1
Table 17.8 INT_MSK0 changed to 0xE0
Table 24.0-Register Summary, address E0 assigned to INT_MSK0 and address
E1 assigned to INT_MSK1
Document 38-08035 Rev. *F
Page 68 of 68
相关型号:
CY7C64013-SCT
Microcontroller, 8-Bit, OTPROM, 12MHz, CMOS, PDSO28, 0.300 INCH, PLASTIC, SOIC-28
CYPRESS
CY7C64013-WC
Microcontroller, 8-Bit, UVPROM, 12MHz, CMOS, CDIP28, 0.300 INCH, WINDOWED, CERDIP-28
CYPRESS
©2020 ICPDF网 联系我们和版权申明