PD46184182BF1-E33-EQ1 [RENESAS]
18M-BIT DDR II SRAM 2-WORD BURST OPERATION; 18M位DDR II SRAM的2字突发操作型号: | PD46184182BF1-E33-EQ1 |
厂家: | RENESAS TECHNOLOGY CORP |
描述: | 18M-BIT DDR II SRAM 2-WORD BURST OPERATION |
文件: | 总34页 (文件大小:611K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Datasheet
μPD46184182B
μPD46184362B
R10DS0114EJ0200
Rev.2.00
18M-BIT DDR II SRAM
2-WORD BURST OPERATION
Nov 09, 2012
Description
The μPD46184182B is a 1,048,576-word by 18-bit and the μPD46184362B is a 524,288-word by 36-bit synchronous
double data rate static RAM fabricated with advanced CMOS technology using full CMOS six-transistor memory cell.
The μPD46184182B and μPD46184362B integrate unique synchronous peripheral circuitry and a burst counter. All input
registers controlled by an input clock pair (K and K#) are latched on the positive edge of K and K#.
These products are suitable for application which require synchronous operation, high speed, low voltage, high density
and wide bit configuration. These products are packaged in 165-pin PLASTIC BGA.
Features
• 1.8 ± 0.1 V power supply
• 165-pin PLASTIC BGA (13 x 15)
• HSTL interface
• PLL circuitry for wide output data valid window and future frequency scaling
• Pipelined double data rate operation
• Common data input/output bus
• Two-tick burst for low DDR transaction size
• Two input clocks (K and K#) for precise DDR timing at clock rising edges only
• Two output clocks (C and C#) for precise flight time
and clock skew matching-clock and data delivered together to receiving device
• Internally self-timed write control
• Clock-stop capability. Normal operation is restored in 20 μs after clock is resumed.
• User programmable impedance output (35 to 70 Ω)
• Fast clock cycle time : 3.3 ns (300 MHz), 4.0 ns (250 MHz)
• Simple control logic for easy depth expansion
• JTAG 1149.1 compatible test access port
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 1 of 34
μPD46184182B, μPD46184362B
Ordering Information
Core
Supply
Voltage
Operating
Ambient
Organization
Cycle
time
Clock
frequency
Part No.
Package
(word x bit)
Temperature
μPD46184182BF1-E33-EQ1-A
μPD46184182BF1-E40-EQ1-A
μPD46184362BF1-E33-EQ1-A
μPD46184362BF1-E40-EQ1-A
μPD46184182BF1-E33Y-EQ1-A
μPD46184182BF1-E40Y-EQ1-A
μPD46184362BF1-E33Y-EQ1-A
μPD46184362BF1-E40Y-EQ1-A
μPD46184182BF1-E33-EQ1
μPD46184182BF1-E40-EQ1
μPD46184362BF1-E33-EQ1
μPD46184362BF1-E40-EQ1
μPD46184182BF1-E33Y-EQ1
μPD46184182BF1-E40Y-EQ1
μPD46184362BF1-E33Y-EQ1
μPD46184362BF1-E40Y-EQ1
1M x 18
3.3ns
4.0ns
3.3ns
4.0ns
3.3ns
4.0ns
3.3ns
4.0ns
3.3ns
4.0ns
3.3ns
4.0ns
3.3ns
4.0ns
3.3ns
4.0ns
300MHz
250MHz
300MHz
250MHz
300MHz
250MHz
300MHz
250MHz
300MHz
250MHz
300MHz
250MHz
300MHz
250MHz
300MHz
250MHz
TA = 0 to 70°C
165-pin
PLASTIC
BGA
1.8 ± ±0.1 V
512K x 36
1M x 18
(13 x 15)
Lead-free
1.8 ± ±0.1 V TA = −40 to 85°C
512K x 36
1M x 18
TA = 0 to 70°C
165-pin
PLASTIC
BGA
1.8 ± ±0.1 V
512K x 36
1M x 18
(13 x 15)
Lead
1.8 ± ±0.1 V TA = −40 to 85°C
512K x 36
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 2 of 34
μPD46184182B, μPD46184362B
Pin Arrangement
165-pin PLASTIC BGA (13 x 15)
(Top View)
[μPD46184182B]
1M x 18
1
CQ#
NC
2
VSS/72M
DQ9
NC
3
4
5
BW1#
NC/288M
A
6
7
NC/144M
BW0#
A
8
9
A
10
VSS/36M
NC
11
CQ
A
B
C
D
E
F
A
R, W#
A
K#
K
LD#
A
NC
NC
NC
NC
NC
NC
NC
VDDQ
NC
NC
NC
NC
NC
NC
A
DQ8
NC
NC
NC
VSS
A0
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
A
VSS
DQ7
NC
NC
NC
DQ10
DQ11
NC
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
A
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
A
VSS
NC
NC
NC
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
NC
DQ6
DQ5
NC
NC
DQ12
NC
NC
G
H
J
NC
DQ13
VDDQ
NC
NC
DLL#
NC
VREF
NC
VREF
DQ4
NC
ZQ
NC
K
L
NC
NC
DQ14
NC
DQ3
DQ2
NC
NC
DQ15
NC
NC
M
N
P
R
NC
NC
DQ1
NC
NC
NC
DQ16
DQ17
A
VSS
VSS
NC
NC
NC
A
A
C
A
A
NC
DQ0
TDI
TDO
TCK
A
A
C#
A
A
TMS
A0, A
: Address inputs
TMS
: IEEE 1149.1 Test input
: IEEE 1149.1 Test input
: IEEE 1149.1 Clock input
: IEEE 1149.1 Test output
: HSTL input reference input
: Power Supply
DQ0 to DQ17
LD#
: Data inputs / outputs
: Synchronous load
: Read Write input
: Byte Write data select
: Input clock
TDI
TCK
TDO
VREF
VDD
R, W#
BW0#, BW1#
K, K#
C, C#
: Output clock
VDDQ
VSS
: Power Supply
CQ, CQ#
ZQ
: Echo clock
: Ground
: Output impedance matching
: PLL disable
NC
: No connection
DLL#
NC/xxM : Expansion address for xxMb
Remarks 1. ×××# indicates active LOW.
2. Refer to Package Dimensions for the index mark.
3. 2A, 7A, 10A and 5B are expansion addresses : 10A for 36Mb
: 10A and 2A for 72Mb
: 10A, 2A and 7A for 144Mb
: 10A, 2A, 7A and 5B for 288Mb
2A and 10A of this product can also be used as NC.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 3 of 34
μPD46184182B, μPD46184362B
Pin Arrangement
165-pin PLASTIC BGA (13 x 15)
(Top View)
[μPD46184362B]
512K x 36
1
CQ#
NC
2
3
4
5
6
7
BW1#
BW0#
A
8
9
A
10
VSS/72M
NC
11
A
B
C
D
E
F
R, W# BW2#
K#
K
LD#
A
CQ
VSS/144M NC/36M
DQ27
NC
DQ18
DQ28
DQ19
DQ20
DQ21
DQ22
VDDQ
DQ32
DQ23
DQ24
DQ34
DQ25
DQ26
A
A
BW3#
A
NC
NC
NC
NC
NC
NC
VDDQ
NC
NC
NC
NC
NC
NC
A
DQ8
DQ7
DQ16
DQ6
DQ5
DQ14
ZQ
NC
VSS
A0
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
A
VSS
DQ17
NC
NC
DQ29
NC
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
A
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
A
VSS
NC
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
DQ15
NC
NC
DQ30
DQ31
VREF
NC
G
H
J
NC
NC
DLL#
NC
VREF
DQ13
DQ12
NC
DQ4
DQ3
DQ2
DQ1
DQ10
DQ0
TDI
K
L
NC
NC
NC
DQ33
NC
M
N
P
R
NC
DQ11
NC
NC
DQ35
NC
VSS
VSS
NC
A
A
C
A
A
DQ9
TMS
TDO
TCK
A
A
C#
A
A
A0, A
: Address inputs
TMS
: IEEE 1149.1 Test input
: IEEE 1149.1 Test input
: IEEE 1149.1 Clock input
: IEEE 1149.1 Test output
: HSTL input reference input
: Power Supply
DQ0 to DQ35
LD#
: Data inputs / outputs
: Synchronous load
: Read Write input
TDI
TCK
TDO
VREF
VDD
R, W#
BW0# to BW3# : Byte Write data select
K, K#
C, C#
CQ, CQ#
ZQ
: Input clock
: Output clock
VDDQ
VSS
: Power Supply
: Echo clock
: Ground
: Output impedance matching
: PLL disable
NC
: No connection
DLL#
NC/xxM : Expansion address for xxMb
Remarks 1. ×××# indicates active LOW.
2. Refer to Package Dimensions for the index mark.
3. 2A, 3A and 10A are expansion addresses : 3A for 36Mb
: 3A and 10A for 72Mb
: 3A, 10A and 2A for 144Mb
2A and 10A of this product can also be used as NC.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 4 of 34
μPD46184182B, μPD46184362B
Pin Description
(1/2)
Symbol
Type
Input
Description
A0
A
Synchronous Address Inputs: These inputs are registered and must meet the setup and
hold times around the rising edge of K. All transactions operate on a burst of two words
(one clock period of bus activity). A0 is used as the lowest order address bit permitting a
random starting address within the burst operation on x18 and x36 devices. These inputs
are ignored when device is deselected, i.e., NOP (LD# = HIGH).
DQ0 to
DQxx
Input/Outpu Synchronous Data IOs: Input data must meet setup and hold times around the rising
t
edges of K and K#. Output data is synchronized to the respective C and C# data clocks
or to K and K# if C and C# are tied to HIGH.
x18 device uses DQ0 to DQ17.
x36 device uses DQ0 to DQ35.
LD#
Input
Input
Input
Synchronous Load: This input is brought LOW when a bus cycle sequence is to be
defined. This definition includes address and read/write direction. All transactions operate
on a burst of 2 data (one clock period of bus activity).
R, W#
BWx#
Synchronous Read/Write Input: When LD# is LOW, this input designates the access type
(READ when R, W# is HIGH, WRITE when R, W# is LOW) for the loaded address. R, W#
must meet the setup and hold times around the rising edge of K.
Synchronous Byte Writes: When LOW these inputs cause their respective byte to be
registered and written during WRITE cycles. These signals must meet setup and hold
times around the rising edges of K and K# for each of the two rising edges comprising the
WRITE cycle. See Pin Arrangement for signal to data relationships.
x18 device uses BW0#, BW1#.
x36 device uses BW0# to BW3#.
See Byte Write Operation for relation between BWx# and Dxx.
K, K#
C, C#
Input
Input
Input Clock: This input clock pair registers address and control inputs on the rising edge
of K, and registers data on the rising edge of K and the rising edge of K#. K# is ideally
180 degrees out of phase with K. All synchronous inputs must meet setup and hold times
around the clock rising edges.
Output Clock: This clock pair provides a user controlled means of tuning device output
data. The rising edge of C# is used as the output timing reference for first output data.
The rising edge of C is used as the output reference for second output data. Ideally, C# is
180 degrees out of phase with C. When use of K and K# as the reference instead of C
and C#, then fixed C and C# to HIGH. Operation cannot be guaranteed unless C and C#
are fixed to HIGH (i.e. toggle of C and C#)
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 5 of 34
μPD46184182B, μPD46184362B
(2/2)
Symbol
Type
Description
CQ, CQ#
Output
Synchronous Echo Clock Outputs. The rising edges of these outputs are tightly matched
to the synchronous data outputs and can be used as a data valid indication. These signals
run freely and do not stop when DQ tristates. If C and C# are stopped (if K and K# are
stopped in the single clock mode), CQ and CQ# will also stop.
ZQ
Input
Input
Output Impedance Matching Input: This input is used to tune the device outputs to the
system data bus impedance. DQ, CQ and CQ# output impedance are set to 0.2 x RQ,
where RQ is a resistor from this bump to ground. The output impedance can be
minimized by directly connect ZQ to VDDQ. This pin cannot be connected directly to GND
or left unconnected. The output impedance is adjusted every 20 μs upon power-up to
account for drifts in supply voltage and temperature. After replacement for a resistor, the
new output impedance is reset by implementing power-on sequence.
DLL#
PLL Disable: When debugging the system or board, the operation can be performed at a
clock frequency slower than TKHKH (MAX.) without the PLL circuit being used, if DLL# =
LOW. The AC/DC characteristics cannot be guaranteed. For normal operation, DLL# must
be HIGH and it can be connected to VDDQ through a 10 kΩ or less resistor.
TMS
TDI
Input
Input
Output
−
IEEE 1149.1 Test Inputs: 1.8 V I/O level. These balls may be left Not Connected if the
JTAG function is not used in the circuit.
TCK
TDO
VREF
VDD
IEEE 1149.1 Clock Input: 1.8 V I/O level. This pin must be tied to VSS if the JTAG
function is not used in the circuit.
IEEE 1149.1 Test Output: 1.8 V I/O level.
When providing any external voltage to TDO signal, it is recommended to pull up to VDD.
HSTL Input Reference Voltage: Nominally VDDQ/2. Provides a reference voltage for the
input buffers.
Supply
Supply
Power Supply: 1.8 V nominal. See Recommended DC Operating Conditions and DC
Characteristics for range.
VDDQ
Power Supply: Isolated Output Buffer Supply. Nominally 1.5 V. 1.8 V is also permissible.
See Recommended DC Operating Conditions and DC Characteristics for range.
VSS
Supply
Power Supply: Ground
NC
−
No Connect: These signals are not connected internally.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 6 of 34
μPD46184182B, μPD46184362B
Block Diagram
CLK
Burst
Logic
A0'
A0
D0
Q0
R
Address
Address
W#
Register
E
LD#
Compare
C#
C
A0''
A0'''
Output control
Logic
Write address
Register
K
E
E
A0'
Input
Register
/A0'
A0'
ZQ
0
2 :1
MUX
Memory
Array
CLK
/A0'
K
1
A0'
Output Buffer
E
DQ
0
1
K#
Input
Register
E
A0'''
Output Enable
Register
C
R, W#
R, W#`
Register
E
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 7 of 34
μPD46184182B, μPD46184362B
Power-On Sequence in DDR II SRAM
DDR II SRAMs must be powered up and initialized in a predefined manner to prevent undefined operations.
The following timing charts show the recommended power-on sequence.
The following power-up supply voltage application is recommended: VSS, VDD, VDDQ, VREF, then VIN. VDD and VDD
can be applied simultaneously, as long as VDDQ does not exceed VDD by more than 0.5 V during power-up. The
Q
following power-down supply voltage removal sequence is recommended: VIN, VREF, VDDQ, VDD, VSS. VDD and VDD
can be removed simultaneously, as long as VDDQ does not exceed VDD by more than 0.5 V during power-down.
Q
Power-On Sequence
Apply power and tie DLL# to HIGH.
Apply VDDQ before VREF or at the same time as VREF
.
Provide stable clock for more than 20 μs to lock the PLL.
Continuous min.4 NOP(LD# = high) cycles are required after PLL lock up is done.
PLL Constraints
The PLL uses K clock as its synchronizing input and the input should have low phase jitter which is specified as
TKC var. The PLL can cover 120 MHz as the lowest frequency. If the input clock is unstable and the PLL is
enabled, then the PLL may lock onto an undesired clock frequency.
Power-On Waveforms
V
DD/VDDQ
V
DD/VDDQ Stable (< ±0.1 V DC per 50 ns)
Fix HIGH (or tied to VDDQ)
DLL#
Clock
20 μs or more
Stable Clock
Unstable Clock
Normal Operation
Start
4 Times NOP
LD#
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 8 of 34
μPD46184182B, μPD46184362B
Burst Sequence
Linear Burst Sequence Table
A0
A0
1
External Address
0
1
1st Internal Burst Address
0
Truth Table
Operation
LD# R, W# CLK
DQ
WRITE cycle
L
L
L → H
Data in
Load address, input write data on
consecutive K and K# rising edge
READ cycle
Input data
Input clock
Data out
D(A1)
D(A2)
K(t+1) ↑
K#(t+1) ↑
L
H
L → H
Load address, read data on
consecutive C and C# rising edge
NOP (No operation)
Clock stop
Output data
Output clock
Q(A1)
Q(A2)
C#(t+1) ↑
C(t+2) ↑
H
×
×
L → H
High-Z
Previous state
×
Stopped
Remarks 1. H : HIGH, L : LOW, × : don’t care, ↑ : rising edge.
2. Data inputs are registered at K and K# rising edges. Data outputs are delivered at C and C# rising edges
except if C and C# are HIGH then Data outputs are delivered at K and K# rising edges.
3. All control inputs in the truth table must meet setup/hold times around the rising edge (LOW to HIGH) of
K. All control inputs are registered during the rising edge of K.
4. This device contains circuitry that ensure the outputs to be in high impedance during power-up.
5. Refer to state diagram and timing diagrams for clarification.
6. A1 refers to the address input during a WRITE or READ cycle. A2 refers to the next internal burst
address in accordance with the linear burst sequence.
7. It is recommended that K = K# = C = C# when clock is stopped. This is not essential but permits most
rapid restart by overcoming transmission line charging symmetrically.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 9 of 34
μPD46184182B, μPD46184362B
Byte Write Operation
[μPD46184182B]
Operation
K
L → H
−±
L → H
−±
L → H
−±
L → H
−±
K#
−±
L → H
−±
L → H
−±
L → H
−±
BW0#
BW1#
Write DQ0 to DQ17
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
Write DQ0 to DQ8
Write DQ9 to DQ17
Write nothing
L → H
Remarks 1. H : HIGH, L : LOW, → : rising edge.
2. Assumes a WRITE cycle was initiated. BW0# and BW1# can be altered for any portion of the BURST
WRITE operation provided that the setup and hold requirements are satisfied.
[μPD46184362B]
Operation
K
L → H
−±
L → H
−±
L → H
−±
L → H
−±
L → H
−±
L → H
−±
K#
−±
L → H
−±
L → H
−±
L → H
−±
L → H
−±
L → H
−±
BW0#
BW1#
BW2#
BW3#
Write DQ0 to DQ35
Write DQ0 to DQ8
Write DQ9 to DQ17
Write DQ18 to DQ26
Write DQ27 to DQ35
Write nothing
0
0
0
0
1
1
1
1
1
1
1
1
0
0
1
1
0
0
1
1
1
1
1
1
0
0
1
1
1
1
0
0
1
1
1
1
0
0
1
1
1
1
1
1
0
0
1
1
L → H
Remarks 1. H : HIGH, L : LOW, → : rising edge.
2. Assumes a WRITE cycle was initiated. BW0# to BW3# can be altered for any portion of the BURST
WRITE operation provided that the setup and hold requirements are satisfied.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 10 of 34
μPD46184182B, μPD46184362B
Bus Cycle State Diagram
LOAD NEW
ADDRESS
Count = 0
Load, Count = 2
WRITE DOUBLE
Load, Count = 2
READ DOUBLE
Write
Read
Count = Count + 2
Count = Count + 2
Load
NOP,
NOP,
Count = 2
Count = 2
NOP
NOP
Supply voltage provided
Power UP
Remarks 1. A0 is internally advanced in accordance with the burst order table.
Bus cycle is terminated after burst count = 2.
2. State machine control timing sequence is controlled by K.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 11 of 34
μPD46184182B, μPD46184362B
Electrical Characteristics
Absolute Maximum Ratings
Parameter
Supply voltage
Symbol
Conditions
Rating
−0.5 to +2.5±
Unit
V
VDD
Output supply voltage
Input voltage
VDD
Q
−0.5 to VDD
V
VIN
VI/O
TA
−0.5 to VDD+0.5 (2.5 V MAX.)
−0.5 to VDDQ+0.5 (2.5 V MAX.)
0 to 70
V
Input / Output voltage
Operating ambient temperature
V
(E** series)
°C
°C±
°C
(E**Y series)
−40 to 85
Storage temperature
Tstg
−55 to +125±
Caution Exposing the device to stress above those listed in Absolute Maximum Ratings could cause
permanent damage. The device is not meant to be operated under conditions outside the limits
described in the operational section of this specification. Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
Recommended DC Operating Conditions (TA = 0 to 70°C, TA = −40 to 85°C)
Parameter
Supply voltage
Symbol Conditions
MIN.
1.7
TYP.
MAX.
1.9
Unit Note
VDD
1.8
V
Output supply voltage
Input HIGH voltage
Input LOW voltage
Clock input voltage
Reference voltage
VDD
Q
1.4
VDD
V
V
V
V
V
1
VIH (DC)
VIL (DC)
VIN
VREF +0.1
−0.3
VDDQ+0.3
VREF±−0.1
VDDQ+0.3
0.95
1, 2
1, 2
1, 2
−0.3
VREF
0.68
Notes 1. During normal operation, VDDQ must not exceed VDD
.
2. Power-up: VIH ≤ VDDQ + 0.3 V and VDD ≤ 1.7 V and VDDQ ≤ 1.4 V for t ≤ 200 ms
Recommended AC Operating Conditions (TA = 0 to 70°C, TA = −40 to 85°C)
Parameter
Input HIGH voltage
Input LOW voltage
Symbol Conditions
MIN.
MAX.
Unit Note
VIH (AC)
VIL (AC)
VREF±+0.2
V
V
1
1
±
VREF±−0.2
Note 1. Overshoot: VIH (AC) ≤ VDD + 0.7 V (2.5 V MAX.) for t ≤ TKHKH/2
Undershoot: VIL (AC) ≥±−0.5 V for t ≤ TKHKH/2
Control input signals may not have pulse widths less than TKHKL (MIN.) or operate at cycle rates less than
TKHKH (MIN.).
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 12 of 34
μPD46184182B, μPD46184362B
DC Characteristics 1 (TA = 0 to 70°C, VDD = 1.8 ± 0.1 V)
MAX.
Parameter
Symbol
Test condition
MIN.
Unit Note
x18
x36
Input leakage current
I/O leakage current
ILI
−2
−2
μA
μA
+2
+2
ILO
IDD
Operating supply current
(Read cycle / Write cycle)
VIN ≤ VIL or VIN ≥ VIH,
II/O = 0 mA,
-E33
-E40
-E33
-E40
470
430
410
380
510
470
430
400
mA
Cycle = MAX.
Standby supply current
(NOP)
ISB1
VIN ≤ VIL or VIN ≥ VIH,
II/O = 0 mA,
Cycle = MAX.
Inputs static
|IOH| ≤ 0.1 mA
Note1
mA
VDDQ
Output HIGH voltage
Output LOW voltage
VOH(Low)
VOH
VDDQ−0.2
VDDQ/2−0.12
VSS
V
V
V
V
3, 4
3, 4
3, 4
3, 4
VDDQ/2+0.12
0.2
VOL(Low)
VOL
IOL ≤ 0.1 mA
Note2
VDDQ/2−0.12
VDDQ/2+0.12
Notes 1. Outputs are impedance-controlled. | IOH | = (VDDQ/2)/(RQ/5) ± 15% for values of 175 Ω ≤ RQ ≤ 350 Ω.
2. Outputs are impedance-controlled. IOL = (VDDQ/2)/(RQ/5) ± 15% for values of 175 Ω ≤ RQ ≤ 350 Ω.
3. AC load current is higher than the shown DC values.
4. HSTL outputs meet JEDEC HSTL Class I standards.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 13 of 34
μPD46184182B, μPD46184362B
DC Characteristics 2 (TA = −40 to 85°C, VDD = 1.8 ± 0.1 V)
Parameter
Symbol
Test condition
MIN.
MAX.
Unit Note
x18
x36
Input leakage current
I/O leakage current
ILI
−2
−2
+2
+2
μA
μA
ILO
IDD
Operating supply current
(Read cycle / Write cycle)
VIN ≤ VIL or VIN ≥ VIH,
II/O = 0 mA,
-E33Y
-E40Y
-E33Y
-E40Y
600
560
530
500
640
600
550
520
mA
Cycle = MAX.
Standby supply current
(NOP)
ISB1
VIN ≤ VIL or VIN ≥ VIH,
II/O = 0 mA,
mA
Cycle = MAX.
Inputs static
Output HIGH voltage
Output LOW voltage
VOH(Low) |IOH| ≤ 0.1 mA
VOH
VOL(Low) IOL ≤ 0.1 mA
VOL
VDDQ−0.2
VDDQ/2−0.12
VSS
VDD
Q
V
V
V
V
3, 4
3, 4
3, 4
3, 4
Note1
VDDQ/2+0.12
0.2
Note2
VDDQ/2−0.12
VDDQ/2+0.12
Notes 1. Outputs are impedance-controlled. | IOH | = (VDDQ/2)/(RQ/5) ± 15% for values of 175 Ω ≤ RQ ≤ 350 Ω.
2. Outputs are impedance-controlled. IOL = (VDDQ/2)/(RQ/5) ± 15% for values of 175 Ω ≤ RQ ≤ 350 Ω.
3. AC load current is higher than the shown DC values.
4. HSTL outputs meet JEDEC HSTL Class I standards.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 14 of 34
μPD46184182B, μPD46184362B
Capacitance (TA = 25°C, f = 1 MHz)
Parameter
Symbol
Test conditions
MIN.
MAX.
Unit
Input capacitance
CIN
VIN = 0 V
5
pF
(Address, Control)
Input / Output capacitance
(DQ, CQ, CQ#)
CI/O
Cclk
VI/O = 0 V
Vclk = 0 V
7
6
pF
pF
Clock Input capacitance
Remark These parameters are periodically sampled and not 100% tested.
Thermal Characteristics
Parameter
Thermal resistance
Symbol
Substrate
4-layer
Airflow
TYP.
Unit
θ ja
0 m/s
1 m/s
0 m/s
1 m/s
0 m/s
1 m/s
0 m/s
1 m/s
16.5
13.2
15.5
12.6
0.07
0.13
0.06
0.12
3.86
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W±
°C/W
°C/W
from junction to ambient air
8-layer
4-layer
8-layer
Thermal characterization parameter
from junction to the top center
of the package surface
Ψ jt±
±
Thermal resistance
from junction to case
θ jc
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 15 of 34
μPD46184182B, μPD46184362B
AC Characteristics (TA = 0 to 70°C, TA = −40 to 85°C, VDD = 1.8 ± 0.1 V)
AC Test Conditions (VDD = 1.8 ± 0.1 V, VDDQ = 1.4 V to VDD)
Input waveform (Rise / Fall time ≤ 0.3 ns)
1.25 V
0.75 V
0.75 V
Test Points
0.25 V
Output waveform
V
DDQ / 2
Test Points
VDDQ / 2
Output load condition
Figure 1. External load at test
V
DDQ / 2
0.75 V
50 Ω
V
REF
ZO = 50 Ω
SRAM
250 Ω
ZQ
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 16 of 34
μPD46184182B, μPD46184362B
Read and Write Cycle
Parameter
Symbol
-E33,-E33Y
(300 MHz)
-E40,-E40Y
(250 MHz)
Unit
Note
MIN.
MAX.
MIN.
MAX.
Clock
Average Clock cycle time
(K, K#, C, C#)
TKHKH
3.3
8.4
0.2
4.0
8.4
0.2
ns
1
2
Clock phase jitter (K, K#, C, C#)
Clock HIGH time (K, K#, C, C#)
Clock LOW time (K, K#, C, C#)
Clock HIGH to Clock# HIGH
(K → K#, C → C#)
TKC var
TKHKL
TKLKH
ns
ns
ns
ns
1.32
1.32
1.49
1.6
1.6
1.8
TKHK#H
Clock# HIGH to Clock HIGH
(K# → K, C# → C)
Clock to data clock
TK#HKH
TKHCH
1.49
0
1.8
0
ns
ns
1.45
1.8
(K → C, K# → C#)
PLL lock time (K, C)
TKC lock
20
30
20
30
μs
ns
3
4
K static to PLL reset
TKC reset
Output Times
CQ HIGH to CQ# HIGH
(CQ → CQ#)
CQ# HIGH to CQ HIGH
TCQHCQ#H
TCQ#HCQH
1.24±
1.24±
1.55±
1.55±
ns
ns
5
5
(CQ# → CQ)
C, C# HIGH to output valid
C, C# HIGH to output hold
C, C# HIGH to echo clock valid
C, C# HIGH to echo clock hold
CQ, CQ# HIGH to output valid
CQ, CQ# HIGH to output hold
C HIGH to output High-Z
C HIGH to output Low-Z
TCHQV
TCHQX
0.45
0.45
0.27
0.45
0.45
0.45
0.3
ns
ns
ns
ns
ns
ns
ns
ns
−0.45
−0.45
−0.27
−0.45
−0.45
−0.45
−0.3
TCHCQV
TCHCQX
TCQHQV
TCQHQX
TCHQZ
6
6
0.45
TCHQX1
−0.45
Setup Times
Address valid to K rising edge
Synchronous load input (LD#),
read write input (R, W#) valid to
K rising edge
TAVKH
TIVKH
0.4
0.4
0.5
0.5
ns
ns
7
7
Data inputs and write data
select inputs (BWx#) valid to
K, K# rising edge
TDVKH
0.3
0.35
ns
7
Hold Times
K rising edge to address hold
K rising edge to
TKHAX
TKHIX
0.4
0.4
0.5
0.5
ns
ns
7
7
synchronous load input (LD#),
read write input (R, W#) hold
K, K# rising edge to data inputs
and write data select inputs
(BWx#) hold
TKHDX
0.3
0.35
ns
7
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 17 of 34
μPD46184182B, μPD46184362B
Notes 1. When debugging the system or board, these products can operate at a clock frequency slower than TKHKH
(MAX.) without the PLL circuit being used, if DLL# = LOW. Read latency (RL) is changed to 1.0 clock
cycle in this operation. The AC/DC characteristics cannot be guaranteed, however.
2. Clock phase jitter is the variance from clock rising edge to the next expected clock rising edge. TKC var
(MAX.) indicates a peak-to-peak value.
3.
VDD slew rate must be less than 0.1 V DC per 50 ns for PLL lock retention.
PLL lock time begins once VDD and input clock are stable.
It is recommended that the device is kept NOP (LD# = HIGH) during these cycles.
4. K input is monitored for this operation. See below for the timing.
K
TKC reset
or
K
TKC reset
5. Guaranteed by design.
6. Echo clock is very tightly controlled to data valid / data hold. By design, there is a ± 0.1 ns variation from
echo clock to data. The data sheet parameters reflect tester guardbands and test setup variations.
7. This is a synchronous device. All addresses, data and control lines must meet the specified setup and hold
times for all latching clock edges.
Remarks 1. This parameter is sampled.
2. Test conditions as specified with the output loading as shown in AC Test Conditions unless otherwise
noted.
3. Control input signals may not be operated with pulse widths less than TKHKL (MIN.).
4. If C, C# are tied HIGH, K, K# become the references for C, C# timing parameters.
5. VDDQ is 1.5 V DC.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 18 of 34
μPD46184182B, μPD46184362B
Read and Write Timing
READ
(burst of 2) (burst of 2) (burst of 2)
NOP
READ
(burst of 2) (burst of 2)
NOP
NOP
WRITE
WRITE
READ
1
2
3
4
5
6
7
8
9
10
TKHKH
K
TKHKL
TKLKH
TKHK#H
TK#HKH
K#
LD#
TIVKH
TKHIX
R, W#
TAVKH TKHAX
A0
A1
A2
A3
A4
Address
DQ
TKHDX
TKHDX
TDVKH
TDVKH
D20
D21
D30
D31
Q00 Q01 Q10
TCHQX
Q11
Qx2
Q40 Q41
TCQHQX
TCQHQV
TCHQX1
TCHQV
TCHQZ
TCHQX
TKHCH
TCHQV
TKHCH
CQ
TCHCQX
TCHCQV
TCQHCQ#H TCQ#HCQH
CQ#
C
TCHCQX
TCHCQV
TKHKL TKLKH TKHKH TKHK#H TK#HKH
C#
Remarks 1. Q01 refers to output from address A0.
Q02 refers to output from the next internal burst address following A0, etc.
2. Outputs are disabled (high impedance) 2.5 clock cycles after the last READ (LD# = LOW, R, W# =
HIGH) is input in the sequences of [READ]-[NOP].
3. The second NOP cycle at the cycle “5” is not necessary for correct device operation;
however, at high clock frequencies it may be required to prevent bus contention.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 19 of 34
μPD46184182B, μPD46184362B
Application Example
R =
250 Ω
R =
250 Ω
ZQ
CQ#
CQ
ZQ
CQ#
CQ
. . .
SRAM#1
SRAM#4
DQ
A
DQ
A
LD# R, W# BWx# C/C# K/K#
LD# R, W# BWx# C/C# K/K#
V
t
SRAM
Controller
R
Data IO
Vt
Address
LD#
R
R, W#
BW#
SRAM#1 CQ/CQ#
Vt
R
R
SRAM#4 CQ/CQ#
Vt
Source CLK/CLK#
Return CLK/CLK#
Vt
R
R = 50 Ω
Vt = Vref
Remark AC Characteristics are defined at the condition of SRAM outputs, CQ, CQ# and DQ with termination.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 20 of 34
μPD46184182B, μPD46184362B
JTAG Specification
These products support a limited set of JTAG functions as in IEEE standard 1149.1.
Test Access Port (TAP) Pins
Pin name
TCK
Pin assignments
Description
2R
Test Clock Input. All input are captured on the rising edge of TCK and all
outputs propagate from the falling edge of TCK.
TMS
TDI
10R
11R
Test Mode Select. This is the command input for the TAP controller state
machine.
Test Data Input. This is the input side of the serial registers placed between
TDI and TDO. The register placed between TDI and TDO is determined by the
state of the TAP controller state machine and the instruction that is currently
loaded in the TAP instruction.
TDO
1R
Test Data Output. This is the output side of the serial registers placed between
TDI and TDO. Output changes in response to the falling edge of TCK.
Remark The device does not have TRST (TAP reset). The Test-Logic Reset state is entered while TMS is held HIGH
for five rising edges of TCK. The TAP controller state is also reset on the SRAM POWER-UP.
JTAG DC Characteristics (TA = 0 to 70°C, VDD = 1.8 ± 0.1 V, unless otherwise noted)
Parameter
Symbol
Conditions
MIN.
−5.0
−5.0
MAX.
+5.0
+5.0
Unit
JTAG Input leakage current
JTAG I/O leakage current
ILI
0 V ≤ VIN ≤ VDD
0 V ≤ VIN ≤ VDDQ,
Outputs disabled
μA
μA
±
ILO
JTAG input HIGH voltage
JTAG input LOW voltage
JTAG output HIGH voltage
VIH
VIL
1.3
−0.3
1.6
VDD+0.3
+0.5
V
V
VOH1
VOH2
VOL1
VOL2
| IOHC | = 100 μA
V
| IOHT | = 2 mA
1.4
V
JTAG output LOW voltage
I
OLC = 100 μA
0.2
0.4
V
IOLT = 2 mA
V
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 21 of 34
μPD46184182B, μPD46184362B
JTAG AC Test Conditions
Input waveform (Rise / Fall time ≤ 1 ns)
1.8 V
0.9 V
0 V
0.9 V
Test Points
Output waveform
0.9 V
Test Points
0.9 V
Output load
Figure 2. External load at test
V
TT = 0.9 V
50 Ω
ZO = 50 Ω
TDO
20 pF
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 22 of 34
μPD46184182B, μPD46184362B
JTAG AC Characteristics (TA = 0 to 70°C)
Parameter
Symbol
Conditions
MIN.
MAX.
Unit
Clock
Clock cycle time
Clock frequency
Clock HIGH time
Clock LOW time
tTHTH
fTF
tTHTL
tTLTH
50
±
ns
MHz
ns
20
20
20
ns
Output time
TCK LOW to TDO unknown
TCK LOW to TDO valid
tTLOX
tTLOV
0
ns
ns
±
10
Setup time
TMS setup time
TDI valid to TCK HIGH
Capture setup time
tMVTH
tDVTH
tCS
5
5
5
ns
ns
ns
Hold time
TMS hold time
tTHMX
tTHDX
tCH
5
5
5
ns
ns
ns
TCK HIGH to TDI invalid
Capture hold time
JTAG Timing Diagram
t
THTH
TCK
t
MVTH
t
THTL
t
TLTH
TMS
TDI
t
THMX
t
DVTH
t
THDX
t
TLOV
t
TLOX
TDO
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 23 of 34
μPD46184182B, μPD46184362B
Scan Register Definition (1)
Register name
Description
Instruction register
The instruction register holds the instructions that are executed by the TAP controller
when it is moved into the run-test/idle or the various data register state. The register can
be loaded when it is placed between the TDI and TDO pins. The instruction register is
automatically preloaded with the IDCODE instruction at power-up whenever the controller
is placed in test-logic-reset state.
Bypass register
ID register
The bypass register is a single bit register that can be placed between TDI and TDO. It
allows serial test data to be passed through the RAMs TAP to another device in the scan
chain with as little delay as possible.
The ID Register is a 32 bit register that is loaded with a device and vendor specific 32 bit
code when the controller is put in capture-DR state with the IDCODE command loaded in
the instruction register. The register is then placed between the TDI and TDO pins when
the controller is moved into shift-DR state.
Boundary register
The boundary register, under the control of the TAP controller, is loaded with the contents
of the RAMs I/O ring when the controller is in capture-DR state and then is placed
between the TDI and TDO pins when the controller is moved to shift-DR state. Several
TAP instructions can be used to activate the boundary register.
The Scan Exit Order tables describe which device bump connects to each boundary
register location. The first column defines the bit’s position in the boundary register. The
second column is the name of the input or I/O at the bump and the third column is the
bump number.
Scan Register Definition (2)
Register name
Instruction register
Bypass register
ID register
Bit size
Unit
bit
3
1
bit
32
107
bit
Boundary register
bit
ID Register Definition
ID [31:28] vendor
revision no.
ID [11:1] vendor
ID no.
Part number
Organization
ID [27:12] part no.
ID [0] fix bit
μPD46184182B
μPD46184362B
1M x 18
512K x 36
XXXX
XXXX
0000 0000 0001 0011
0000 0000 0001 0100
00000010000
00000010000
1
1
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 24 of 34
μPD46184182B, μPD46184362B
SCAN Exit Order
Bit
Signal name
Bump
ID
Bit
Signal name
Bump
ID
Bit
Signal name
Bump
ID
no.
x18
x36
no.
x18
x36
no.
x18
x36
1
C#
C
6R
6P
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
NC
NC
10D
9E
73
74
NC
2C
3E
2D
2E
1E
2F
3F
1G
1F
3G
2G
1J
2
DQ11
NC
DQ20
DQ29
3
A
6N
DQ7
NC
DQ17
DQ16
10C
11D
9C
75
4
A
7P
76
NC
NC
5
A
7N
NC
NC
77
6
A
7R
9D
78
DQ12
NC
DQ30
DQ21
DQ8
7
A
8R
11B
11C
9B
79
8
A
8P
NC
DQ7
80
NC
NC
9
A
9R
NC
NC
CQ
–
81
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
DQ0
11P
10P
10N
9P
10B
11A
Internal
9A
82
DQ13
NC
DQ22
DQ31
NC
DQ9
83
NC
NC
84
NC
NC
A
85
2J
DQ1
NC
DQ11
DQ10
10M
11N
9M
A
8B
86
DQ14
NC
DQ23
DQ32
3K
3J
A
7C
87
A0
NC
NC
6C
88
NC
NC
2K
1K
2L
9N
LD#
8A
89
DQ2
11L
11M
9L
NC
NC
BW1#
7A
90
DQ15
NC
DQ33
DQ24
NC
NC
DQ1
BW0#
K
7B
91
3L
NC
NC
6B
92
NC
NC
1M
1L
10L
11K
10K
9J
K#
6A
93
DQ3
BW3#
BW2#
5B
94
DQ16
NC
DQ25
DQ34
3N
3M
1N
2M
3P
2N
2P
1P
3R
4R
4P
5P
5N
5R
DQ12
BW1#
5A
95
NC
NC
R, W#
4A
96
NC
NC
9K
A
A
5C
97
DQ4
NC
DQ13
DQ4
10J
11J
11H
10G
9G
4B
98
DQ17
NC
DQ26
DQ35
A
NC
3A
99
ZQ
NC
DLL#
CQ#
1H
100
101
102
103
104
105
106
107
NC
NC
A
1A
NC
DQ9
NC
DQ27
DQ18
2B
DQ5
11F
11G
9F
3B
A
NC
NC
DQ14
DQ15
NC
NC
1C
A
NC
NC
1B
A
10F
11E
10E
DQ10
NC
DQ19
DQ28
3D
A
DQ6
3C
A
NC
1D
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 25 of 34
μPD46184182B, μPD46184362B
JTAG Instructions
Instructions
Description
EXTEST
The EXTEST instruction allows circuitry external to the component package to be tested.
Boundary-scan register cells at output pins are used to apply test vectors, while those at
input pins capture test results. Typically, the first test vector to be applied using the
EXTEST instruction will be shifted into the boundary scan register using the PRELOAD
instruction. Thus, during the update-IR state of EXTEST, the output drive is turned on and
the PRELOAD data is driven onto the output pins.
IDCODE
BYPASS
The IDCODE instruction causes the ID ROM to be loaded into the ID register when the
controller is in capture-DR mode and places the ID register between the TDI and TDO pins
in shift-DR mode. The IDCODE instruction is the default instruction loaded in at power up
and any time the controller is placed in the test-logic-reset state.
When the BYPASS instruction is loaded in the instruction register, the bypass register is
placed between TDI and TDO. This occurs when the TAP controller is moved to the shift-
DR state. This allows the board level scan path to be shortened to facilitate testing of other
devices in the scan path.
SAMPLE / PRELOAD SAMPLE / PRELOAD is a Standard 1149.1 mandatory public instruction. When the
SAMPLE / PRELOAD instruction is loaded in the instruction register, moving the TAP
controller into the capture-DR state loads the data in the RAMs input and DQ pins into the
boundary scan register. Because the RAM clock(s) are independent from the TAP clock
(TCK) it is possible for the TAP to attempt to capture the I/O ring contents while the input
buffers are in transition (i.e., in a metastable state). Although allowing the TAP to sample
metastable input will not harm the device, repeatable results cannot be expected. RAM
input signals must be stabilized for long enough to meet the TAPs input data capture setup
plus hold time (tCS plus tCH). The RAMs clock inputs need not be paused for any other
TAP operation except capturing the I/O ring contents into the boundary scan register.
Moving the controller to shift-DR state then places the boundary scan register between the
TDI and TDO pins.
SAMPLE-Z
If the SAMPLE-Z instruction is loaded in the instruction register, all RAM DQ pins are
forced to an inactive drive state (high impedance) and the boundary register is connected
between TDI and TDO when the TAP controller is moved to the shift-DR state.
JTAG Instruction Coding
IR2
0
IR1
0
IR0
0
Instruction
EXTEST
Note
0
0
1
IDCODE
0
1
0
SAMPLE-Z
1
2
0
1
1
RESERVED
SAMPLE / PRELOAD
RESERVED
RESERVED
BYPASS
1
0
0
1
0
1
2
2
1
1
0
1
1
1
Notes 1. TRISTATE all DQ pins and CAPTURE the pad values into a SERIAL SCAN LATCH.
2. Do not use this instruction code because the vendor uses it to evaluate this product.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 26 of 34
μPD46184182B, μPD46184362B
Output Pin States of CQ, CQ# and DQ
Instructions
Control-Register Status
Output Pin Status
CQ,CQ#
Update
Update
SRAM
SRAM
High-Z
High-Z
SRAM
SRAM
SRAM
SRAM
DQ
EXTEST
0
1
0
1
0
1
0
1
0
1
High-Z
Update
SRAM
SRAM
High-Z
High-Z
SRAM
SRAM
SRAM
SRAM
IDCODE
SAMPLE-Z
SAMPLE
BYPASS
Remark The output pin statuses during each instruction vary according
to the Control-Register status (value of Boundary Scan
Register, bit no. 48).
Boundary Scan
Register
CAPTURE
Register
There are three statuses:
Update : Contents of the “Update Register” are output to the
output pin (DDR Pad).
SRAM
Output
Update
Register
SRAM : Contents of the SRAM internal output “SRAM
Output” are output to the output pin (DDR Pad).
High-Z :The output pin (DDR Pad) becomes high
impedance by controlling of the “High-Z JTAG
ctrl”.
Update
DDR
Pad
SRAM
SRAM
Output
Driver
High-Z
The Control-Register status is set during Update-DR at the
EXTEST or SAMPLE instruction.
High-Z
JTAG ctrl
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 27 of 34
μPD46184182B, μPD46184362B
Boundary Scan Register Status of Output Pins CQ, CQ# and DQ
Instructions
SRAM Status
Boundary Scan Register Status
Note
CQ,CQ#
Pad
DQ
Pad
Pad
EXTEST
READ (Low-Z)
NOP (High-Z)
READ (Low-Z)
NOP (High-Z)
READ (Low-Z)
NOP (High-Z)
READ (Low-Z)
NOP (High-Z)
READ (Low-Z)
NOP (High-Z)
Pad
IDCODE
SAMPLE-Z
SAMPLE
BYPASS
−±−
No definition
−±−
Pad
Pad
Pad
Pad
Internal
Internal
−±−
Internal
Pad
No definition
−±−
Remark The Boundary Scan Register statuses during execution each
instruction vary according to the instruction code and SRAM
operation mode.
Boundary Scan
Register
CAPTURE
Register
There are two statuses:
Internal
Pad
: Contents of the output pin (DDR Pad) are captured
in the “CAPTURE Register” in the Boundary Scan
Register.
SRAM
Output
Update
Register
Pad
Internal : Contents of the SRAM internal output “SRAM
Output” are captured in the “CAPTURE Register”
in the Boundary Scan Register.
DDR
Pad
SRAM
Output
Driver
High-Z
JTAG ctrl
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 28 of 34
μPD46184182B, μPD46184362B
TAP Controller State Diagram
1
0
Test-Logic-Reset
0
1
1
1
Run-Test / Idle
Select-DR-Scan
0
Select-IR-Scan
0
1
1
Capture-DR
0
Capture-IR
0
0
0
Shift-DR
1
Shift-IR
1
1
1
Exit1-DR
0
Exit1-IR
0
0
0
Pause-DR
1
Pause-IR
1
0
0
Exit2-DR
1
Exit2-IR
1
Update-DR
Update-IR
1
0
1
0
Disabling the Test Access Port
It is possible to use this device without utilizing the TAP. To disable the TAP Controller without interfering with
normal operation of the device, TCK must be tied to VSS to preclude mid level inputs. TDI and TMS may be left open
but fix them to VDD via a resistor of about 1 kΩ when the TAP controller is not used. TDO should be left unconnected
also when the TAP controller is not used.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 29 of 34
μPD46184182B, μPD46184362B
Run-Test/Idle
Update-IR
Exit1-IR
Shift-IR
Exit2-IR
Pause-IR
Exit1-IR
Shift-IR
Capture-IR
Select-IR-Scan
Select-DR-Scan
Run-Test/Idle
Test-Logic-Reset
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 30 of 34
μPD46184182B, μPD46184362B
Test-Logic-Reset
Select-IR-Scan
Select-DR-Scan
Run-Test/Idle
Update-DR
Exit1-DR
Shift-DR
Exit2-DR
Pause-DR
Exit1-DR
Shift-DR
Capture-DR
Select-DR-Scan
Run-Test/Idle
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 31 of 34
μPD46184182B, μPD46184362B
Package Dimensions
165-PIN PLASTIC BGA(13x15)
w S
B
ZD
B
E
ZE
11
10
9
8
7
A
6
5
D
4
3
2
1
R P N M L K J H G F E D C B A
w
S A
INDEX MARK
A
(UNIT:mm)
ITEM DIMENSIONS
A2
y1
S
D
E
13.00±0.10
15.00±0.10
0.30
S
w
A
1.35±0.11
0.37±0.05
0.98
A1
A2
e
y
e
x
A1
S
S
1.00
M
b
A B
+0.10
−0.05
b
0.50
x
0.10
0.15
y
y1
ZD
ZE
0.25
1.50
0.50
T165F1-100-EQ1
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 32 of 34
μPD46184182B, μPD46184362B
Recommended Soldering Condition
Please consult with our sales offices for soldering conditions of these products.
Types of Surface Mount Devices
μPD46184182BF1-EQ1
μPD46184362BF1-EQ1
:
:
165-pin PLASTIC BGA (13 x 15)
165-pin PLASTIC BGA (13 x 15)
Quality Grade
• A quality grade of the products is “Standard”.
• Anti-radioactive design is not implemented in the products.
• Semiconductor devices have the possibility of unexpected defects by affection of cosmic ray that reach to
the ground and so forth.
R10DS0114EJ0200 Rev.2.00
Nov 09, 2012
Page 33 of 34
Revision History
μPD46184182B, μPD46184362B
Description
Summary
Rev.
Date
Page
-
Rev.1.00
Rev.2.00
’12.06.01
’12.11.09
New Data Sheet
Addition : -E33,-E33Y series, Lead series
Deletion : -E50,-E50Y series
ALL
All trademarks and registered trademarks are the property of their respective owners.
C - 34
相关型号:
©2020 ICPDF网 联系我们和版权申明