F0452C [RENESAS]
Dual Path RF Switch with LNA and DVGA 2.3GHz to 2.7GHz;型号: | F0452C |
厂家: | RENESAS TECHNOLOGY CORP |
描述: | Dual Path RF Switch with LNA and DVGA 2.3GHz to 2.7GHz |
文件: | 总24页 (文件大小:1777K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Dual Path RF Switch with LNA
and DVGA 2.3GHz to 2.7GHz
F0452C
Datasheet
Description
Features
The F0452C is an integrated dual-path RF front-end consisting of
an RF switch and two gain stages with 6dB gain control used in the
analog front-end receiver of an Active Antenna System (AAS). The
F0452C supports frequencies from 2.3GHz to 2.7GHz.
.
Gain at 2.6GHz
• 34dB typical in High Gain Mode
• 28dB typical in Low Gain Mode
1.6dB NF at 2.6GHz
.
.
.
The F0452C provides 34dB gain with +23dBm OIP3, +15dBm
output P1dB, and 1.6dB noise figure (NF) at 2.6GHz. Gain is
reduced 6dB in a single step with a maximum gain settling time of
31ns. The device uses a single 3.3V supply and 130mA of IDD.
+23dBm OIP3 at 2.6GHz
OP1dB at 2.6GHz
• +15dBm in High Gain Mode
• +14dBm in Low Gain Mode
The F0452C is offered in a 6 × 6 × 0.75 mm, 32-pin LGA package
with 50Ω input and output amplifier impedances for ease of
integration into the signal path.
.
.
.
.
.
.
50Ω single-ended input / output amplifier impedances
IDD = 130mA
Independent Standby Mode for power savings
Supply voltage: +3.15V to +3.45V
Competitive Advantage
6 × 6 mm, 32-LGA package
-40°C to +105°C exposed pad operating temperature range
.
.
.
.
High integration
Low noise and high linearity
On-chip matching and bias
Extremely low current consumption
Block Diagram
Typical Applications
.
.
.
.
Multi-mode, multi-carrier receivers
AAS Rx Front-End
4.5G (LTE Advanced)
SW1_IN
5G NR band n40 and n41
STBY1
ATT1_CTRL
SW1_CTRL
SW2_CTRL
ATT2_CTRL
STBY2
SW2_IN
© 2020 Renesas Electronics Corporation
1
May 5, 2020
F0452C Datasheet
Contents
Pin Assignments....................................................................................................................................................................................................4
Pin Descriptions.....................................................................................................................................................................................................5
Absolute Maximum Ratings...................................................................................................................................................................................6
Recommended Operating Conditions ...................................................................................................................................................................7
Electrical Characteristics .......................................................................................................................................................................................8
Thermal Characteristics.......................................................................................................................................................................................12
Typical Operating Conditions ..............................................................................................................................................................................12
Programming.......................................................................................................................................................................................................12
Typical Performance Characteristics...................................................................................................................................................................13
Evaluation Kit Picture ..........................................................................................................................................................................................17
Evaluation Kit Circuit ...........................................................................................................................................................................................18
Application Information........................................................................................................................................................................................20
Power Supplies...........................................................................................................................................................................................20
Control Pin Interface...................................................................................................................................................................................20
Marking Diagram .................................................................................................................................................................................................21
Package Outline Drawings ..................................................................................................................................................................................21
Ordering Information............................................................................................................................................................................................21
Revision History...................................................................................................................................................................................................21
List of Figures
Figure 1. Pin Assignments for 6 × 6 × 0.75 mm 32-LGA – Top View.................................................................................................................4
Figure 2. Rx Mode Gain (High Gain) ................................................................................................................................................................13
Figure 3. Rx Mode Gain (Low Gain).................................................................................................................................................................13
Figure 4. Rx Mode Reverse Isolation (High Gain)............................................................................................................................................13
Figure 5. Rx Mode Reverse Isolation (Low Gain).............................................................................................................................................13
Figure 6. Rx Mode Input Return Loss (High Gain)............................................................................................................................................13
Figure 7. Rx Mode Input Return Loss (Low Gain) ............................................................................................................................................13
Figure 8. Rx Mode Output Return Loss (High Gain).........................................................................................................................................14
Figure 9. Rx Mode Output Return Loss (Low Gain)..........................................................................................................................................14
Figure 10. Rx Mode OP1dB (High Gain) ............................................................................................................................................................14
Figure 11. Rx Mode OP1dB (Low Gain).............................................................................................................................................................14
Figure 12. Rx Mode OIP3 (High Gain)................................................................................................................................................................14
Figure 13. Rx Mode OIP3 (Low Gain) ................................................................................................................................................................14
Figure 14. Rx Mode Noise Figure (High Gain) ...................................................................................................................................................15
Figure 15. Rx Mode Noise Figure (Low Gain) ....................................................................................................................................................15
Figure 16. Tx Mode RF Switch Isolation.............................................................................................................................................................15
Figure 17. Rx Mode Channel Isolation ...............................................................................................................................................................15
© 2020 Renesas Electronics Corporation
2
May 5, 2020
F0452C Datasheet
Figure 18. Stability Factor...................................................................................................................................................................................15
Figure 19. Gain Settling Time.............................................................................................................................................................................16
Figure 20. Gain Step Phase Settling Time .........................................................................................................................................................16
Figure 21. Power OFF Switching Time...............................................................................................................................................................16
Figure 22. Power ON Switching Time.................................................................................................................................................................16
Figure 23. Power OFF to Standby Mode............................................................................................................................................................16
Figure 24. Power ON from Standby Mode..........................................................................................................................................................16
Figure 25. Power ON from Standby Mode.........................................................................................................................................................16
Figure 26. Evaluation Kit: Top View....................................................................................................................................................................17
Figure 27. Evaluation Kit: Bottom View ..............................................................................................................................................................17
Figure 28. Electrical Schematic...........................................................................................................................................................................18
Figure 29. Control Pin Interface Schematic.........................................................................................................................................................20
List of Tables
Table 1. Pin Descriptions...................................................................................................................................................................................5
Table 2. Absolute Maximum Ratings.................................................................................................................................................................6
Table 3. Recommended Operating Conditions .................................................................................................................................................7
Table 4. Electrical Characteristics .....................................................................................................................................................................8
Table 5. Electrical Characteristics – RX Path in RX Mode Cascaded Performance .......................................................................................10
Table 6. Electrical Characteristics – RX Path in RX Mode Cascaded Performance and TX Performance .....................................................11
Table 7. Thermal Characteristics.....................................................................................................................................................................12
Table 8. Gain Step Truth Table .......................................................................................................................................................................12
Table 9. Standby and RF Switch Truth Table..................................................................................................................................................12
Table 10. Bill of Material (BOM) ........................................................................................................................................................................19
© 2020 Renesas Electronics Corporation
3
May 5, 2020
F0452C Datasheet
Pin Assignments
Figure 1. Pin Assignments for 6 × 6 × 0.75 mm 32-LGA – Top View
ATT1_CTRL
1
GND
SW1_IN
GND
NC
24
23
22
21
20
19
18
17
STBY1
2
SW1_CTRL
GND
3
4
5
6
7
8
GND
NC
SW2_CTRL
STBY2
GND
SW2_IN
GND
ATT2_CTRL
© 2020 Renesas Electronics Corporation
4
May 5, 2020
F0452C Datasheet
Pin Descriptions
Table 1.
Pin Descriptions
Number
Name
Description
1-bit 6dB gain control for path 1. (Low /open = no attenuation; High = 6dB attenuation). A 500kΩ pull-down
resistor is connected between this input and GND.
1
2
ATT1_CTRL
STBY1
Standby (Low/open = path 1 power ON; High = path 1 power OFF). A 500kΩ pull-down resistor is connected
between this input and GND.
RF SWITCH 1 control (Low /open = select main RX PATH 1; High = switch output). SW1_CTRL also puts path
1 into Standby Mode for minimum current consumption. A 500kΩ pull-down resistor is connected between this
input and GND.
3
SW1_CTRL
GND
4, 5, 9, 11,
13, 15, 17,
19, 22, 24,
Ground these pins.
26, 28, 30, 32
RF SWITCH 2 control (Low /open = select main RX PATH 2; High = switch output). SW2_CTRL also puts path
2 into Standby Mode for minimum current consumption. A 500kΩ pull-down resistor is connected between this
input and GND.
6
7
SW2_CTRL
STBY2
Standby (Low /open = path 2 power ON; High = path 2 power OFF). A 500kΩ pull-down resistor is connected
between this input and GND.
1-bit 6dB gain control for path 2. (Low /open = no attenuation; High = 6dB attenuation). A 500kΩ pull-down
resistor connects between this input and GND.
8
10
ATT2_CTRL
RX2_OUT
VDD
RF output path 2 matched to 50Ω. Use external DC block as close to the pin as possible.
Power supply. Bypass to GND with capacitors shown in the F0452C Application Circuit as close as possible to
the pins.
12, 14, 27, 29
RF2 switch output matched to 50Ω. Use external 50Ω terminating resistor with proper power rating as required
for the application.
16
SW2_OUT
18
23
SW2_IN
SW1_IN
RF2 switch input matched to 50Ω. Use an external DC block as close to the pin as possible.
RF1 switch input matched to 50Ω. Use an external DC block as close to the pin as possible.
RF1 switch output matched to 50Ω. Use an external 50Ω terminating resistor with proper power rating as
required for the application.
25
31
SW1_OUT
RX1_OUT
NC
RF output path 1 matched to 50Ω. Use an external DC block as close to the pin as possible.
These pins can be left unconnected, or be connected to ground (recommended). Use a via as close to the pin
as possible if grounded.
20, 21
Exposed Pad. Internally connected to GND. Solder this exposed pad to a PCB pad that uses multiple ground
vias to provide heat transfer out of the device into the PCB ground planes. These multiple via grounds are also
required to achieve the specified RF performance.
―
EPAD
© 2020 Renesas Electronics Corporation
5
May 5, 2020
F0452C Datasheet
Absolute Maximum Ratings
Stresses beyond those listed below may cause permanent damage to the device. Functional operation of the device at these or any other
conditions beyond those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
Table 2.
Absolute Maximum Ratings
Parameter
Symbol
VDD
Minimum
-0.3
Maximum
+3.6
Units
VDD to GND
V
V
STBY1, STBY2, ATT1_CTRL, ATT2_CTRL, SW1_CTRL, SW2_CTRL to GND
VCTRL
-0.3
VDD + 0.25
SW1_IN, SW2_IN, RX1_OUT, RX2_OUT, SW1_OUT, SW2_OUT to GND
Externally Applied DC Voltage
VSW
-50
50
mV
TX Mode CW Average Input Power +7.5dB PAR at SW1_IN, SW2_IN Ports,
10s, 89% Duty Cycle
50Ω, TEPAD = 105°C [a], VDD = +3.3V
PABS_TX
+31
+33 [b]
dBm
RX Mode Average Input Power +7.5dB PAR at SW1_IN, SW2_IN Ports,
1 Hour Single Event, 50% Duty Cycle
50Ω, TEPAD = 105°C [a], VDD = +3.3V
PABS_RX
+8
dBm
Storage Temperature Range
TST
-65
+150
+260
°C
°C
Lead Temperature (soldering, 10s)
TLEAD
Electrostatic Discharge – HBM
(JEDEC/ESDA JS-001-2012)
1500
VESDHBM
V
V
(Class 1C)
Electrostatic Discharge – CDM
(JEDEC JS-002-2014)
500
VESDCDM
(Class C2A)
ALL pins except pins 16, 18, 23, 25
Electrostatic Discharge – CDM
(JEDEC JS-002-2014)
Pins 16, 18, 23, 25
125
VESDCDM
V
(Class C0B)
[a] TEPAD = temperature of the exposed paddle.
[b] RF input exposures greater than +31dBm and up to +33dBm for multiple extended periods will affect device reliability and lifetime if the maximum
recommended input junction temperature is exceeded.
© 2020 Renesas Electronics Corporation
6
May 5, 2020
F0452C Datasheet
Recommended Operating Conditions
Table 3.
Recommended Operating Conditions
Parameter
Symbol
Condition
Minimum
3.15
Typical
Maximum
Units
V
Power Supply Voltage
VDD
3.3
3.45
+105
2.7
Operating Temperature Range
RF Frequency Range
TEPAD
fRF
Exposed Paddle
-40
°C
2.3
GHz
TX Mode CW Average Input Power,
+7.5dB PAR, Full Life Time [a]
PMAX_TX
89% Duty Cycle
89% Duty Cycle
+30[b]
-25
dBm
dBm
50Ω, VDD = +3.3V
RX Mode CW Average Input Power,
+7.5dB PAR, Full Life Time [a]
PMAX_RX
50Ω, VDD = +3.3V
Port Impedance (SW1_IN, SW2_IN,
RX1_OUT, RX2_OUT)
ZRF
TJ
50
Ω
Junction Temperature
+125
°C
[a] Assumes device environmental temperature cycling within the specified exposed pad operating temperature range of -40°C and 105°C and a
maximum junction temperature of 125°C.
[b] Operation beyond the maximum recommended operating input power level should be limited and have reduced exposed pad temperatures to
maintain device reliability per foundry guidelines. Electrical characteristics and lifetime are not guaranteed for RF input power levels beyond what
is specified in this table.
© 2020 Renesas Electronics Corporation
7
May 5, 2020
F0452C Datasheet
Electrical Characteristics
Table 4.
Electrical Characteristics
See F0452C Application Circuit. Specifications apply when operated as an RX RF amplifier with VDD = +3.3V, TEPAD = +25°C, STBYx = Low,
RX output power = -10dBm, ZS = ZL = 50Ω, and EVKit trace and connector losses are de-embedded unless otherwise noted.
Parameter
Symbol
Condition
Minimum
Typical
Maximum
Units
Lower of
(VDD, 3.3)
Logic Input High Threshold
VIH
1.17[a]
V
Logic Input Low Threshold
Logic Current
VIL
-0.3
0.63
10
V
IIH, IIL
For each control pin
2 paths in RX Mode
-10
µA
130
70
180
1 path in RX Mode
1 path in TX Mode
100
1 path in RX Mode
DC Current
IDD
67
5
mA
1 path in Standby Mode
1 path in TX Mode
1 path in Standby Mode
2 paths in Standby Mode
5
6
Gain Step
GSTEP
dB
dB
Relative to maximum gain,
over-voltage, and temperature
Gain Step Absolute Error
Relative Phase Gain Step
Gain Step Settling Time [b]
GSTEP_ERR
GSTEP_PH
GSTEP_SET
±0.5
28
deg
ns
50% control logic to RF output
within ±0.1dB of final value
20
31
30
50% control logic to RF output
within ±1 degree of final value
Gain Step Phase Settling Time [b]
Power ON Switching Time [b]
GSTEP_PHSET
16
ns
To RX Mode from TX Mode
50% control logic to RF output
settled to within ±0.1dB of final
value
SWON
1
µs
To TX Mode from RX Mode
50% control logic to RF input
settled within ±0.1dB of final
value
Power OFF Switching Time [b]
SWOFF
0.5
µs
© 2020 Renesas Electronics Corporation
8
May 5, 2020
F0452C Datasheet
Parameter
Symbol
Condition
Minimum
Typical
Maximum
Units
To RX Mode from Standby
Mode
Power ON from Standby Mode [b]
SWON_STANDBY
1
1
µs
50% STBYx to RF output
settled within ±0.1dB of final
value
To Standby Mode from RX
Mode
Power OFF to Standby Mode [b]
SWOFF_STANDBY
µs
50% STBYx to gain below
-25dB from maximum gain
[a] Items in the “Minimum”/“Maximum” columns in bold italics are guaranteed by test. Items in the “Minimum”/“Maximum” columns not in bold italics
are guaranteed by design characterization.
[b] fRF = 2.6GHz. Assumes the control signal is clean and no external RC circuitry is required on the pin. Adding RC circuitry increases switching
time. Timing tests performed with a control logic signal of +3.3V and a rise/fall time ≤ 30ns.
© 2020 Renesas Electronics Corporation
9
May 5, 2020
F0452C Datasheet
Table 5.
Electrical Characteristics – RX Path in RX Mode Cascaded Performance
See the F0452C Application Circuit. Specifications apply when operated as an RX RF amplifier with VDD = +3.3V, fRF = 2.6GHz, TEPAD = +25°C,
STBYx = Low, RX output power = -10dBm, ZS = ZL = 50Ω, and EVKit trace and connector losses are de-embedded unless otherwise noted.
Parameter
Symbol
Condition
Minimum
Typical
Maximum
Units
Measured at SW1_IN, SW2_IN,
High/Low Gain Mode,
16[a]
fRF = 2.4GHz
Measured at SW1_IN, SW2_IN,
High/Low Gain Mode,
Input Return Loss
RLIN
20
dB
fRF = 2.6GHz
Measured at SW1_IN, SW2_IN,
High/Low Gain Mode,
6
fRF = 2.3GHz to 2.7GHz
Measured at RX1_OUT,
RX2_OUT,
Output Return Loss
RLOUT
7
dB
dB
High/Low Gain Modes,
fRF = 2.3GHz to 2.7GHz
Reverse Isolation, RX1_OUT to
SW1_IN, or RX2_OUT to SW2_IN
ISOREV
fRF = 2.3GHz to 2.7GHz
50
58
34
GHG
GHG_TEMP
GLG
High Gain Mode
32
31
37
38
Gain
dB
dB
TEPAD = -40°C to 105°C
Low Gain Mode
Gain Attenuated
25.5
28
31.5
f
RF = 2.3GHz to 2.7GHz
(Difference between maximum
and minimum gain in each
100MHz subrange within the
specified frequency range)
Gain Ripple
Noise Figure
GRIPPLE
±0.75
dB
dB
Measured at antenna port
ideally matched to LNA
1.6
1.5
1.7
2.3
NF
TEPAD = 105°C
Low Gain Mode
[a] Items in the “Minimum”/“Maximum” columns in bold italics are guaranteed by test. Items in the “Minimum”/“Maximum” columns NOT in bold italics
are guaranteed by design characterization.
© 2020 Renesas Electronics Corporation
10
May 5, 2020
F0452C Datasheet
Table 6.
Electrical Characteristics – RX Path in RX Mode Cascaded Performance and TX Performance
See the F0452C Application Circuit. Specifications apply when operated as an RX RF amplifier with VDD = +3.3V, fRF = 2.6GHz, TEPAD = +25°C,
STBYx = Low, RX output power = -10dBm, ZS = ZL = 50Ω, and EVKit trace and connector losses are de-embedded unless otherwise noted.
Parameter
Symbol
Condition
Pout = 0dBm/tone
Minimum
Typical
Maximum
Units
OIP31
23[a]
5MHz tone separation
Pout = 0dBm/tone
OIP32
OIP33
5MHz tone separation
TEPAD = -40°C to 105°C
20
Pout = 0dBm/tone
5MHz tone separation
Low Gain Mode
Output Third-Order Intercept Point
dBm
23
Pout = 0dBm/tone
5MHz tone separation
Low Gain Mode
OIP34
18
TEPAD = -40°C to 105°C
OP1dB1
OP1dB2
OP1dB3
OP1dB4
High Gain Mode [b]
15
14
High Gain Mode
11
10
TEPAD = -40°C to 105°C
Output 1dB Compression
dBm
Low Gain Mode
Low Gain Mode
TEPAD = -40°C to 105°C
RFISO1 = �ꢀꢁ1_ꢂꢃꢄ
ꢅ
ꢀꢁ2_ꢂꢃꢄ
ꢆꢇ
with -60 ≤ SW1_IN ≤ -30dBm
Channel Isolation
ISOCH
54
55
64
65
dB
dB
RFISO2 = �ꢀꢁ2_ꢂꢃꢄ
ꢅ
ꢀꢁ1_ꢂꢃꢄ
ꢆꢇ
with -60 ≤ SW2_IN ≤ -30dBm
TX Mode
RF Switch Isolation
ISOSW
Measured at SW_IN to
RX_OUT of the same channel
[a] Items in the “Minimum”/“Maximum” columns in bold italics are guaranteed by test. Items in the “Minimum”/“Maximum” columns not in bold italics
are guaranteed by design characterization.
[b] In the OP1dB calculation formula, “G” denotes the gain of each part instance at the frequency of interest and appropriate HIGH / LOW gain state.
© 2020 Renesas Electronics Corporation
11
May 5, 2020
F0452C Datasheet
Thermal Characteristics
Table 7.
Thermal Characteristics
Parameter
Symbol
Value
Units
Junction-to-Ambient Thermal Resistance
θJA
31.2
°C/W
Junction-to-Case Thermal Resistance
(Case is defined as the exposed paddle)
θJC_BOT
3.4
°C/W
Moisture Sensitivity Rating (Per J-STD-020)
MSL3
Typical Operating Conditions
Unless otherwise noted:
.
.
.
.
.
.
VDD = +3.3V
TEPAD = 25°C
ZL = ZS = 50Ω single-ended with matching networks
STBY1 = STBY2 = Low or open
SW_CTRL = Low or open
Gain Setting = High Gain Mode
.
PIN ≤ -30dBm
.
.
All temperatures are referenced to the exposed paddle
Evaluation kit traces and connector losses are de-embedded
Programming
Table 8.
Gain Step Truth Table
ATT1_CTRL, ATT2_CTRL
Attenuation Setting
Low or NC
High
0dB
6dB
Table 9.
Standby and RF Switch Truth Table
In TX Mode, the amplifiers are Off but the bias will remain On for fast turn-on recovery time.
STBY1, STBY2
Low or NC
Low or NC
High
SW1_CTRL, SW2_CTRL
Low or NC
Mode
RX
Amplifier State
On
Off
Off
High
TX
High or Low or NC
Standby
© 2020 Renesas Electronics Corporation
12
May 5, 2020
F0452C Datasheet
Typical Performance Characteristics
Figure 2. Rx Mode Gain (High Gain)
Figure 3. Rx Mode Gain (Low Gain)
Figure 4. Rx Mode Reverse Isolation
(High Gain)
Figure 5. Rx Mode Reverse Isolation
(Low Gain)
Figure 6. Rx Mode Input Return Loss
(High Gain)
Figure 7. Rx Mode Input Return Loss
(Low Gain)
© 2020 Renesas Electronics Corporation
13
May 5, 2020
F0452C Datasheet
Figure 8. Rx Mode Output Return Loss
(High Gain)
Figure 9. Rx Mode Output Return Loss
(Low Gain)
Figure 10. Rx Mode OP1dB (High Gain)
Figure 11. Rx Mode OP1dB (Low Gain)
Figure 12. Rx Mode OIP3 (High Gain)
Figure 13. Rx Mode OIP3 (Low Gain)
© 2020 Renesas Electronics Corporation
14
May 5, 2020
F0452C Datasheet
Figure 14. Rx Mode Noise Figure (High Gain)
Figure 15. Rx Mode Noise Figure (Low Gain)
Figure 16. Tx Mode RF Switch Isolation
Figure 17. Rx Mode Channel Isolation
Figure 18. Stability Factor
© 2020 Renesas Electronics Corporation
15
May 5, 2020
F0452C Datasheet
Figure 19. Gain Settling Time
Figure 20. Gain Step Phase Settling Time
Figure 21. Power OFF Switching Time
Figure 22. Power ON Switching Time
Figure 23. Power OFF to Standby Mode
Figure 24. Power ON from Standby Mode
© 2020 Renesas Electronics Corporation
16
May 5, 2020
F0452C Datasheet
Evaluation Kit Picture
Figure 26. Evaluation Kit: Top View
Figure 27. Evaluation Kit: Bottom View
© 2020 Renesas Electronics Corporation
17
May 5, 2020
F0452C Datasheet
Evaluation Kit Circuit
Figure 28. Electrical Schematic
© 2020 Renesas Electronics Corporation
18
May 5, 2020
F0452C Datasheet
Table 10. Bill of Material (BOM)
Part Reference
C2,C3,C4,C5
C7,C9,C11,C13
C8,C10,C12,C14
C17,C18,C19,C20
C15
Qty
DNI
DNI
4
Description
Manufacturer Part #
GRM1555C1H101J
GRM155R71H103J
GRM155R61A105KE15D
GJM1555C1H8R0B
GRM188R71H103K
ERJ-2GE0R00X
Manufacturer
MURATA
100pF ±5%, 50V, C0G Ceramic Capacitor (0402)
10nF ±5%, 50V, X7R Ceramic Capacitor (0402)
1µF ±10% 10V Ceramic Capacitor X5R 0402
8pF ±0.1pF 50V Ceramic Capacitor C0G,NP0 (0402)
10nF ±5%, 50V, X7R Ceramic Capacitor (0603)
0Ω Resistors (0402)
MURATA
MURATA
4
MURATA
1
MURATA
R1,R2,R3,R4,R5,R6
R7
6
PANASONIC
PANASONIC
PANASONIC
1
1kΩ ±1%, 1/10W, Resistor (0402)
ERJ-2RKF1001X
R8
1
1.3kΩ ±1%, 1/10W, Resistor (0402)
ERJ-2RKF1301X
J1,J2,J3,J4,J5,J6,
J10,J11
Cinch
Connectivity
8
1
1
SMA Edge Mount
142-0761-881
10-89-7100
J12
J9
CONN HEADER VERT 2X5 POS GOLD
3M
Emerson
Johnson
Edge Launch SMA(0.375 inch pitch ground, tab) (50Ohm)
142-0701-851
SW1
U1
1
1
1
8-pin DIP Switch (3 POS)
Dual Path RF +LNA+DVGA 5x5 QFN
Printed Circuit Board
KAT1108E
IDE-Switch
IDT
F0452C/F0453C LEG32K
F0452C/F0453C Stripline Rev. B
PCB
Keystone
Electronics
TEST POINT
DNI
BLACK/GND TP1
5001
5000
Keystone
Electronics
TEST POINT
C1,C6,C16
DNI
3
RED/VCC TP2
DNI
© 2020 Renesas Electronics Corporation
19
May 5, 2020
F0452C Datasheet
Application Information
Power Supplies
A common VDD power supply should be used for all pins requiring DC power. All supply pins should be bypassed with external capacitors to
minimize noise and fast transients. Supply noise can degrade the noise figure, and fast transients can trigger ESD clamps and cause them to
fail. Supply voltage change or transients should have a slew rate smaller than 1V / 20µs. In addition, all control pins should remain at
0V (±0.3V) while the supply voltage ramps up or while it returns to zero.
Control Pin Interface
If control signal integrity is a concern and clean signals cannot be guaranteed due to overshoot, undershoot, ringing, etc., the following circuit
at the input of each control pin is recommended. This applies to control pins 1, 2, 3, 6, 7, and 8 shown in Figure 29.
Figure 29. Control Pin Interface Schematic
5 kΩ
ATT1_CTRL
2 pF
5 kΩ
STBY1
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
2 pF
5 kΩ
SW1_CTRL
2 pF
5 kΩ
SW2_CTRL
2 pF
5 kΩ
STBY2
2 pF
5 kΩ
ATT2_CTRL
2 pF
© 2020 Renesas Electronics Corporation
20
May 5, 2020
F0452C Datasheet
Marking Diagram
.
Lines 1 and 2 indicate the part number
Line 3 indicates the following:
• “#” denotes stepping
.
IDTF04
52CLEGK
#YYWW$
• “YY” is the last two digits of the year; “WW” is the work week number when the part was assembled.
• “$” denotes the mark code.
.
Line 4 is the lot number
LOT
Package Outline Drawings
The package outline drawings are appended at the end of this document and are accessible from the link below. The package information is
the most current data available.
www.idt.com/document/psc/32-fclga-package-outline-drawing-600-x-600-x-075-mm-body-460-x-460-mm-epad-05mm-pitch-lfg32p1
Ordering Information
Orderable Part Number
Package
MSL Rating
MSL3
Shipping Packaging
Temperature
-40° to +105°C
-40° to +105°C
F0452CLFGK
6 × 6 × 0.75 mm 32-LGA
6 × 6 × 0.75 mm 32-LGA
Tray
Reel
F0452CLFGK8
F0452CEVB
MSL3
Evaluation Board
Revision History
Revision Date
Description of Change
May 5, 2020
Updated thickness package dimensions to match the POD dimensions.
.
.
Updated Orderable Part Number Information.
Added Application Section Information.
April 21, 2020
February 26, 2020
Initial release.
© 2020 Renesas Electronics Corporation
21
May 5, 2020
32-FCLGA, Package Outline Drawing
6.00 x 6.00 x 0.75 mm Body, 4.60 x 4.60 mm Epad, 0.5mm Pitch
LFG32P1, PSC-4813-01, Rev 00, Page 1
32-FCLGA, Package Outline Drawing
6.00 x 6.00 x 0.75 mm Body, 4.60 x 4.60 mm Epad, 0.5mm Pitch
LFG32P1, PSC-4813-01, Rev 00, Page 2
Package Revision History
Description
Date Created Rev No.
July 18, 2019 Rev 00 Initial Release
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.
相关型号:
©2020 ICPDF网 联系我们和版权申明