SC16C750IA44_技术文档

SC16C750

Universal Asynchronous Receiver/Transmitter (UART)

with 64-byte FIFO

Rev. 04 — 20 June 2003

Product data

1. General description

The SC16C750 is a Universal Asynchronous Receiver and Transmitter (UART) used

for serial data communications. Its principal function is to convert parallel data into

serial data, and vice versa. The UART can handle serial data rates up to 3 Mbits/s.

The SC16C750 is pin compatible with the TL16C750 and it will power-up to be

functionally equivalent to the 16C450. Programming of control registers enables the

added features of the SC16C750. Some of these added features are the 64-byte

receive and transmit FIFOs, automatic hardware ﬂow control. The selectable

auto-ﬂow control feature signiﬁcantly reduces software overload and increases

system efﬁciency while in FIFO mode by automatically controlling serial data ﬂow

using RTS output and CTS input signals. The SC16C750 also provides DMA mode

data transfers through FIFO trigger levels and the TXRDY and RXRDY signals.

On-board status registers provide the user with error indications, operational status,

and modem interface control. System interrupts may be tailored to meet user

requirements. An internal loop-back capability allows on-board diagnostics.

The SC16C750 operates at 5 V, 3.3 V and 2.5 V, the industrial temperature range and

is available in plastic PLCC44 and LQFP64 packages.

2. Features

■ 5 V, 3.3 V and 2.5 V operation

■ Industrial temperature range

■ After reset, all registers are identical to the typical 16C450 register set

■ Capable of running with all existing generic 16C450 software

■ Pin compatibility with the industry-standard ST16C450/550, TL16C450/550,

PC16C450/550

■ Up to 3 Mbits/s transmit/receive operation at 5 V, 2 Mbits/s at 3.3 V, and

1 Mbit/s at 2.5 V

■ 64 byte transmit FIFO

■ 64 byte receive FIFO with error ﬂags

■ Programmable auto-RTS and auto-CTS

◆ In auto-CTS mode, CTS controls transmitter

◆ In auto-RTS mode, RxFIFO contents and threshold control RTS

■ Automatic hardware ﬂow control

■ Software selectable Baud Rate Generator

■ Four selectable Receive interrupt trigger levels

■ Standard modem interface

■ Sleep mode

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

■ Standard asynchronous error and framing bits (Start, Stop, and Parity Overrun

Break)

■ Independent receiver clock input

■ Transmit, Receive, Line Status, and Data Set interrupts independently controlled

■ Fully programmable character formatting:

◆ 5-, 6-, 7-, or 8-bit characters

◆ Even-, Odd-, or No-Parity formats

◆ 1-, 1¹⁄₂-, or 2-stop bit

◆ Baud generation (DC to 3 Mbits/s)

■ False start-bit detection

■ Complete status reporting capabilities

■ 3-State output TTL drive capabilities for bi-directional data bus and control bus

■ Line Break generation and detection

■ Internal diagnostic capabilities:

◆ Loop-back controls for communications link fault isolation

■ Prioritized interrupt system controls

■ Modem control functions (CTS, RTS, DSR, DTR, RI, DCD).

3. Ordering information

Table 1:

Ordering information

Industrial: V_CC= 2.5 V, 3.3 V or 5 V ± 10%; T_amb= −40 °C to +85 °C.

Type number

Package

Name

Description

Version

SC16C750IA44

SC16C750IB64

PLCC44

LQFP64

plastic leaded chip carrier; 44 leads

plastic low proﬁle quad ﬂat package; 64 leads; 10 × 10 × 1.4 mm

SOT187-2

SOT314-2

9397 750 11623

Product data

Rev. 04 — 20 June 2003

2 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

4. Block diagram

SC16C750

TRANSMIT

FIFO

TRANSMIT

SHIFT

TX

REGISTERS

REGISTER

D0–D7

IOR, IOR

IOW, IOW

RESET

DATA BUS

AND

CONTROL LOGIC

FLOW

CONTROL

LOGIC

RECEIVE

FIFO

RECEIVE

SHIFT

RX

REGISTERS

REGISTER

FLOW

CONTROL

LOGIC

REGISTER

SELECT

LOGIC

A0–A2

CS0, CS1, CS2

AS

DDIS

DTR

RTS

OUT1, OUT2

MODEM

CONTROL

LOGIC

INT

TXRDY

RXRDY

CTS

RI

DCD

CLOCK AND

BAUD RATE

GENERATOR

INTERRUPT

CONTROL

LOGIC

DSR

002aaa335

XTAL1 XTAL2

RCLK BAUDOUT

Fig 1. Block diagram.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

3 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

5. Pinning information

5.1 Pinning

D5

D6

D7

7

8

9

39 RESET

38 OUT1

37 DTR

36 RTS

35 OUT2

34 NC

RCLK 10

RX 11

SC16C750IA44

NC 12

TX 13

33 INT

CS0 14

32 RXRDY

31 A0

CS1 15

CS2 16

30 A1

BAUDOUT 17

29 A2

002aaa336

Fig 2. PLCC44 pin conﬁguration.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

4 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

1

2

48

47

46

45

44

43

42

41

40

39

38

XTAL1

XTAL2

NC

D4

NC

D3

D2

NC

D1

D0

NC

V

3

IOW

NC

4

5

6

IOW

NC

7

8

V

SS

SC16C750IB64

9

IOR

CC

10

11

12

NC

RI

NC

DDIS

37 NC

TXRDY 13

NC 14

36 DCD

35 DSR

34 NC

AS 15

NC 16

33 CTS

002aaa364

Fig 3. LQFP64 pin conﬁguration.

5.2 Pin description

Table 2:

Symbol

Pin description

Type Description

PLCC44 LQFP64

A2-A0

AS

28, 27,

26

17, 18, 20

I

Register select. A0-A2 are used during read and write operations to select

the UART register to read from or write to. Refer to Table 3 for register

addresses and refer to AS description.

28

15

Address strobe. When AS is active (LOW), A0, A1, and A2 and CS0, CS1,

and CS2 drive the internal select logic directly; when AS is HIGH, the

register select and chip select signals are held at the logic levels they were

in when the LOW-to-HIGH transition of AS occurred.

BAUDOUT

17

64

O

Baud out. BAUDOUT is a 16× clock signal for the transmitter section of the

UART. The clock rate is established by the reference oscillator frequency

divided by a divisor speciﬁed in the baud generator divisor latches.

BAUDOUT may also be used for the receiver section by tying this output to

RCLK.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

5 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Table 2:

Symbol

Pin description…continued

Type Description

PLCC44 LQFP64

CS0, CS1,

CS2

14, 15,

16

59, 61, 62

I

Chip select. When CS0 and CS1 are HIGH and CS2 is LOW, these three

inputs select the UART. When any of these inputs are inactive, the UART

remains inactive (refer to AS description).

CTS

40

33

Clear to send. CTS is a modem status signal. Its condition can be checked

by reading bit 4 (CTS) of the modem status register. Bit 0 (∆CTS) of the

modem status register indicates that CTS has changed states since the last

read from the modem status register. If the modem status interrupt is

enabled when CTS changes levels and the auto-CTS mode is not enabled,

an interrupt is generated. CTS is also used in the auto-CTS mode to control

the transmitter.

D7-D0

DCD

2-9

42

52, 51, 50, I/O

48, 46, 45,

43, 42

Data bus. Eight data lines with 3-State outputs provide a bi-directional path

for data, control and status information between the UART and the CPU.

36

I

Data carrier detect. DCD is a modem status signal. Its condition can be

checked by reading bit 7 (DCD) of the modem status register. Bit 3 (∆DCD)

of the modem status register indicates that DCD has changed states since

the last read from the modem status register. If the modem status interrupt

is enabled when DCD changes levels, an interrupt is generated.

DDIS

DSR

26

41

12

35

O

I

Driver disable. DDIS is active (LOW) when the CPU is not reading data.

When active, DDIS can disable an external transceiver.

Data set ready. DSR is a modem status signal. Its condition can be

checked by reading bit 5 (DSR) of the modem status register. Bit 1 (∆DSR)

of the modem status register indicates DSR has changed levels since the

last read from the modem status register. If the modem status interrupt is

enabled when DSR changes levels, an interrupt is generated.

DTR

INT

37

33

28

23

O

Data terminal ready. When active (LOW), DTR informs a modem or data

set that the UART is ready to establish communication. DTR is placed in the

active level by setting the DTR bit of the modem control register. DTR is

placed in the inactive level either as a result of a Master Reset, during loop

mode operation, or clearing the DTR bit.

Interrupt. When active (HIGH), INT informs the CPU that the UART has an

interrupt to be serviced. Four conditions that cause an interrupt to be issued

are: a receiver error, received data that is available or timed out (FIFO mode

only), an empty transmitter holding register or an enabled modem status

interrupt. INT is reset (deactivated) either when the interrupt is serviced or

as a result of a Master Reset.

MR

NC

39

34

32

I

Master Reset. When active (HIGH), MR clears most UART registers and

sets the levels of various output signals.

3, 5, 7, 11,

14, 16, 19,

22, 24, 27,

29, 31, 34,

37, 39, 41,

44, 47, 49,

53, 56, 57,

60, 63

Not connected.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

6 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Table 2:

Symbol

Pin description…continued

Type Description

PLCC44 LQFP64

OUT1, OUT2 38, 35

30, 25

O

Outputs 1 and 2. These are user-designated output terminals that are set

to the active (low) level by setting respective modem control register (MCR)

bits (OUT1 and OUT2). OUT1 and OUT2 are set to inactive the (HIGH) level

as a result of Master Reset, during loop mode operations, or by clearing

bit 2 (OUT1) or bit 3 (OUT2) of the MCR.

RCLK

10

54

I

Receiver clock. RCLK is the 16× baud rate clock for the receiver section of

the UART.

IOR, IOR

24, 25

9, 10

Read inputs. When either IOR or IOR is active (LOW or HIGH,

respectively) while the UART is selected, the CPU is allowed to read status

information or data from a selected UART register. Only one of these inputs

is required for the transfer of data during a read operation; the other input

should be tied to its inactive level (i.e., IOR tied LOW or IOR tied HIGH).

RI

43

36

32

38

26

21

I

Ring indicator. RI is a modem status signal. Its condition can be checked

by reading bit 6 (RI) of the modem status register. Bit 2 (∆RI) of the modem

status register indicates that RI has transitioned from a LOW to a HIGH

level since the last read from the modem status register. If the modem

status interrupt is enabled when this transition occurs, an interrupt is

generated.

RTS

O

Request to send. When active, RTS informs the modem or data set that

the UART is ready to receive data. RTS is set to the active level by setting

the RTS modem control register bit and is set to the inactive (HIGH) level

either as a result of a Master Reset or during loop mode operations or by

clearing bit 1 (RTS) of the MCR. In the auto-RTS mode, RTS is set to the

inactive level by the receiver threshold control logic.

RXRDY

Receiver ready. Receiver direct memory access (DMA) signaling is

available with RXRDY. When operating in the FIFO mode, one of two types

of DMA signaling can be selected using the FIFO control register bit 3

(FCR[3]). When operating in the 16C450 mode, only DMA mode 0 is

allowed. Mode 0 supports single-transfer DMA in which a transfer is made

between CPU bus cycles. Mode 1 supports multi-transfer DMA in which

multiple transfers are made continuously until the receiver FIFO has been

emptied. In DMA mode 0 (FCR0 = 0 or FCR0 = 1, FCR3 = 0), when there is

at least one character in the receiver FIFO or receiver holding register,

RXRDY is active (LOW). When RXRDY has been active but there are no

characters in the FIFO or holding register, RXRDY goes inactive (HIGH). In

DMA mode 1 (FCR0 = 1, FCR3 = 1), when the trigger level or the time-out

has been reached, RXRDY goes active (LOW); when it has been active but

there are no more characters in the FIFO or holding register, it goes inactive

(HIGH).

RX

TX

11

13

55

58

I

Serial data input. RX is serial data input from a connected communications

device.

Serial data output. TX is composite serial data output to a connected

communication device. TX is set to the marking (HIGH) level as a result of

Master Reset.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

7 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Table 2:

Symbol

Pin description…continued

Type Description

PLCC44 LQFP64

TXRDY

27

13

O

Transmitter ready. Transmitter DMA signaling is available with TXRDY.

When operating in the FIFO mode, one of two types of DMA signaling can

be selected using FCR[3]. When operating in the 16C450 mode, only DMA

mode 0 is allowed. Mode 0 supports single-transfer DMA in which a transfer

is made between CPU bus cycles. Mode 1 supports multi-transfer DMA in

which multiple transfers are made continuously until the transmit FIFO has

been ﬁlled.

V_CC

44

40

8

Power 2.5 V, 3 V or 5 V supply voltage.

Power Ground voltage.

V_SS

22

IOW, IOW

20, 21

4, 6

I

Write inputs. When either IOW or IOW is active (LOW or HIGH,

respectively) and while the UART is selected, the CPU is allowed to write

control words or data into a selected UART register. Only one of these

inputs is required to transfer data during a write operation; the other input

should be tied to its inactive level (i.e., IOW tied LOW or IOW tied HIGH).

XTAL1

XTAL2^[1]

18

19

1

2

I

Crystal connection or External clock input.

O

Crystal connection or the inversion of XTAL1 if XTAL1 is driven.

[1] In sleep mode, XTAL2 is left ﬂoating.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

8 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

6. Functional description

The SC16C750 provides serial asynchronous receive data synchronization,

parallel-to-serial and serial-to-parallel data conversions for both the transmitter and

receiver sections. These functions are necessary for converting the serial data

stream into parallel data that is required with digital data systems. Synchronization for

the serial data stream is accomplished by adding start and stop bits to the transmit

data to form a data character (character orientated protocol). Data integrity is insured

by attaching a parity bit to the data character. The parity bit is checked by the receiver

for any transmission bit errors. The SC16C750 is fabricated with an advanced CMOS

process to achieve low drain power and high speed requirements.

The SC16C750 is an upward solution that provides 64 bytes of transmit and receive

FIFO memory, instead of none in the 16C450, or 16 in the 16C550. The SC16C750 is

designed to work with high speed modems and shared network environments that

require fast data processing time. Increased performance is realized in the

SC16C750 by the larger transmit and receive FIFOs. This allows the external

processor to handle more networking tasks within a given time. In addition, the four

selectable levels of FIFO trigger interrupt and automatic hardware ﬂow control is

uniquely provided for maximum data throughput performance, especially when

operating in a multi-channel environment. The combination of the above greatly

reduces the bandwidth requirement of the external controlling CPU, increases

performance, and reduces power consumption.

The SC16C750 is capable of operation up to 3 Mbits/s with a 48 MHz external clock

input (at 5 V).

The rich feature set of the SC16C750 is available through internal registers.

Automatic hardware ﬂow control, selectable transmit and receive FIFO trigger level,

selectable TX and RX baud rates, modem interface controls, and a sleep mode are

some of these features.

6.1 Internal registers

The SC16C750 provides 15 internal registers for monitoring and control. These

registers are shown in Table 3. Twelve registers are similar to those already available

in the standard 16C550. These registers function as data holding registers

(THR/RHR), interrupt status and control registers (IER/ISR), a FIFO control register

(FCR), line status and control registers (LCR/LSR), modem status and control

registers (MCR/MSR), programmable data rate (clock) control registers (DLL/DLM),

and a user accessible scratchpad register (SPR). Beyond the general 16C550

features and capabilities, the SC16C750 offers an enhanced feature register that

provides on-board hardware ﬂow control. Register functions are more fully described

in the following paragraphs.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

9 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Table 3:

A2

General register set (THR/RHR, IER/ISR, MCR/MSR, FCR, LSR, SPR)^[1]

Internal registers decoding

A1

A0 READ mode

WRITE mode

0

1

0

1

0

1

0

1

0

1

0

1

0

1

Receive Holding Register

Transmit Holding Register

Interrupt Enable Register

FIFO Control Register

Line Control Register

Modem Control Register

n/a

Interrupt Status Register

Line Status Register

Modem Status Register

Scratchpad Register

n/a

Scratchpad Register

Baud rate register set (DLL/DLM)^[2]

0

LSB of Divisor Latch

MSB of Divisor Latch

0

1

MSB of Divisor Latch

Enhanced register set (EFR, Xon/off 1-2)^[3]

0

1

0

1

0

1

0

1

Enhanced Feature Register

Xon1 word

Enhanced Feature Register

Xon1 word

Xon2 word

Xoff1 word

Xoff2 word

[1] These registers are accessible only when LCR[7] is a logic 0.

[2] These registers are accessible only when LCR[7] is a logic 1.

[3] Enhanced Feature Register, Xon1, 2 and Xoff1, 2 are accessible only when the LCR is set to

‘BF(HEX)’.

6.2 FIFO operation

The 64-byte transmit and receive data FIFOs are enabled by the FIFO Control

Register bit-0 (FCR[0]). With 16C550 devices, the user can set the receive trigger

level, but not the transmit trigger level. The SC16C750 provides independent trigger

levels for both receiver and transmitter. To remain compatible with SC16C550, the

transmit interrupt trigger level is set to 16 following a reset. It should be noted that the

user can set the transmit trigger levels by writing to the FCR register, but activation

will not take place until EFR[4] is set to a logic 1. The receiver FIFO section includes

a time-out function to ensure data is delivered to the external CPU. An interrupt is

generated whenever the Receive Holding Register (RHR) has not been read

following the loading of a character or the receive trigger level has not been reached.

Table 4:

Flow control mechanism

Selected trigger level

(characters)

INT pin activation

Negate RTS

Assert RTS

16-byte FIFO

1

4

1

4

8

4

8

12

14

8

14

10

9397 750 11623

Product data

Rev. 04 — 20 June 2003

10 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Table 4:

Flow control mechanism…continued

Selected trigger level

(characters)

INT pin activation

Negate RTS

Assert RTS

64-byte FIFO

1

16

32

56

60

1

16

32

56

16

32

56

8

16

32

6.3 Hardware ﬂow control

When automatic hardware ﬂow control is enabled, the SC16C750 monitors the CTS

pin for a remote buffer overﬂow indication and controls the RTS pin for local buffer

overﬂows. Automatic hardware ﬂow control is selected by setting EFR[6] (RTS) and

EFR[7] (CTS) to a logic 1. If CTS transitions from a logic 0 to a logic 1 indicating a

ﬂow control request, the SC16C750 will suspend TX transmissions as soon as the

stop bit of the character in process is shifted out. Transmission is resumed after the

CTS input returns to a logic 0, indicating more data may be sent.

With the Auto-RTS function enabled, an interrupt is generated when the receive FIFO

reaches the programmed trigger level. The RTS pin will not be forced to a logic 1

(RTS off), until the receive FIFO reaches the next trigger level. However, the RTS pin

will return to a logic 0 after the data buffer (FIFO) is unloaded to the next trigger level

below the programmed trigger level. However, under the above described conditions,

the SC16C750 will continue to accept data until the receive FIFO is full.

6.4 Time-out interrupts

When two interrupt conditions have the same priority, it is important to service these

interrupts correctly. Receive Data Ready and Receive Time Out have the same

interrupt priority (when enabled by IER[0]). The receiver issues an interrupt after the

number of characters have reached the programmed trigger level. In this case, the

SC16C750 FIFO may hold more characters than the programmed trigger level.

Following the removal of a data byte, the user should re-check LSR[0] for additional

characters. A Receive Time Out will not occur if the receive FIFO is empty. The

time-out counter is reset at the center of each stop bit received or each time the

receive holding register (RHR) is read. The actual time-out value is 4 character time.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

11 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

6.5 Programmable baud rate generator

The SC16C750 supports high speed modem technologies that have increased input

data rates by employing data compression schemes. For example, a 33.6 kbit/s

modem that employs data compression may require a 115.2 kbit/s input data rate.

A 128.0 kbit/s ISDN modem that supports data compression may need an input

data rate of 460.8 kbit/s.

A single baud rate generator is provided for the transmitter and receiver, allowing

independent TX/RX channel control. The programmable Baud Rate Generator is

capable of accepting an input clock up to 48 MHz, as required for supporting a

3 Mbits/s data rate. The SC16C750 can be conﬁgured for internal or external clock

operation. For internal clock oscillator operation, an industry standard microprocessor

crystal (parallel resonant/22-33 pF load) is connected externally between the XTAL1

and XTAL2 pins (see Figure 4). Alternatively, an external clock can be connected to

the XTAL1 pin to clock the internal baud rate generator for standard or custom rates

(see Table 5).

1.5 kΩ

X1

1.8432 MHz

C1

47 pF

C2

100 pF

C1

22 pF

C2

47 pF

002aaa169

Fig 4. Crystal oscillator connection.

The generator divides the input 16× clock by any divisor from 1 to 2¹⁶− 1. The

SC16C750 divides the basic crystal or external clock by 16. The frequency of the

BAUDOUT output pin is exactly 16× (16 times) of the selected baud rate

(BAUDOUT = 16 Baud Rate). Customized baud rates can be achieved by selecting

the proper divisor values for the MSB and LSB sections of baud rate generator.

Programming the Baud Rate Generator registers DLM (MSB) and DLL (LSB)

provides a user capability for selecting the desired ﬁnal baud rate. The example in

Table 5 shows selectable baud rates when using a 1.8432 MHz crystal.

For custom baud rates, the divisor value can be calculated using the following

equation:

XTAL1 clock frequency

serial data rate × 16

Divisor (in decimal) =

(1)

----------------------------------------------------------

9397 750 11623

Product data

Rev. 04 — 20 June 2003

12 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Table 5:

Baud rates using 1.8432 MHz or 3.072 MHz crystal

Using 3.072 MHz crystal

Using 1.8432 MHz crystal

Desired

baud rate

Divisor for

16× clock

Baud rate

error

Desired

baud rate

Divisor for

16× clock

Baud rate

error

50

2304

1536

1047

857

768

384

192

96

50

3840

2560

1745

1428

1280

640

320

160

107

96

75

110

0.026

0.058

110

0.026

0.034

134.5

150

134.5

150

300

600

1200

1800

2000

2400

3600

4800

7200

9600

19200

38400

56000

1200

1800

2000

2400

3600

4800

7200

9600

19200

38400

64

0.312

58

0.69

48

80

32

53

0.628

1.23

24

40

16

27

12

20

6

10

3

5

2

2.86

6.6 DMA operation

The SC16C750 FIFO trigger level provides additional ﬂexibility to the user for block

mode operation. The user can optionally operate the transmit and receive FIFOs in

the DMA mode (FCR[3]). The DMA mode affects the state of the RXRDY and TXRDY

output pins. Tables 6 and 7 show this.

Table 6:

Effect of DMA mode on state of RXRDY pin

Non-DMA mode

DMA mode

1 = FIFO empty

0-to-1 transition when FIFO empties

0 = at least 1 byte in FIFO

1-to-0 transition when FIFO reaches trigger level,

or time-out occurs

Table 7:

Effect of DMA mode on state of TXRDY pin

Non-DMA mode

1 = at least 1 byte in FIFO

0 = FIFO empty

DMA mode

0-to-1 transition when FIFO becomes full

1-to-0 transition when FIFO goes below trigger level

9397 750 11623

Product data

Rev. 04 — 20 June 2003

13 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

6.7 Sleep mode

The SC16C750 is designed to operate with low power consumption. A special sleep

mode is included to further reduce power consumption when the chip is not being

used. With IER[4] enabled (set to a logic 1), the SC16C750 enters the sleep mode,

but resumes normal operation when a start bit is detected, a change of state on any

of the modem input pins RX, RI, CTS, DSR, DCD, or a transmit data is provided by

the user. If the sleep mode is enabled and the SC16C750 is awakened by one of the

conditions described above, it will return to the sleep mode automatically after the last

character is transmitted or read by the user. In any case, the sleep mode will not be

entered while an interrupt(s) is pending. The SC16C750 will stay in the sleep mode of

operation until it is disabled by setting IER[4] to a logic 0.

6.8 Loop-back mode

The internal loop-back capability allows on-board diagnostics. In the loop-back mode,

the normal modem interface pins are disconnected and reconﬁgured for loop-back

internally. MCR[0-3] register bits are used for controlling loop-back diagnostic testing.

In the loop-back mode, OUT1 and OUT2 in the MCR register (bits 2-3) control the

modem RI and DCD inputs, respectively. MCR signals DTR and RTS (bits 0-1) are

used to control the modem CTS and DSR inputs, respectively. The transmitter output

(TX) and the receiver input (RX) are disconnected from their associated interface

pins, and instead are connected together internally (see Figure 5). The CTS, DSR,

DCD, and RI are disconnected from their normal modem control input pins, and

instead are connected internally to DTR, RTS, OUT1 and OUT2. Loop-back test data

is entered into the transmit holding register via the user data bus interface, D0-D7.

The transmit UART serializes the data and passes the serial data to the receive

UART via the internal loop-back connection. The receive UART converts the serial

data back into parallel data that is then made available at the user data interface

D0-D7. The user optionally compares the received data to the initial transmitted data

for verifying error-free operation of the UART TX/RX circuits.

In this mode, the receiver and transmitter interrupts are fully operational. The Modem

Control Interrupts are also operational. However, the interrupts can only be read

using lower four bits of the Modem Status Register (MSR[0-3]) instead of the four

Modem Status Register bits 4-7. The interrupts are still controlled by the IER.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

14 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

SC16C750

TRANSMIT

FIFO

TRANSMIT

SHIFT

TX

REGISTERS

REGISTER

D0–D7

IOR, IOR

IOW, IOW

RESET

DATA BUS

AND

CONTROL LOGIC

FLOW

CONTROL

LOGIC

RECEIVE

SHIFT

REGISTER

RECEIVE

FIFO

REGISTERS

RX

A0–A2

CS0, CS1

FLOW

CONTROL

LOGIC

REGISTER

SELECT

LOGIC

CS2

AS

RTS

DDIS

DSR

DTR

MODEM

CONTROL

LOGIC

CTS

OUT1

RI

INT

TXRDY

RXRDY

CLOCK AND

BAUD RATE

GENERATOR

INTERRUPT

CONTROL

LOGIC

OUT2

DCD

002aaa337

XTAL1

RCLK

XTAL2

BAUDOUT

Fig 5. Internal loop-back mode diagram.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

15 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

7. Register descriptions

Table 8 details the assigned bit functions for the ﬁfteen SC16C750 internal registers.

The assigned bit functions are more fully deﬁned in Section 7.1 through Section 7.11.

Table 8:

SC16C750 internal registers

A2 A1 A0 Register Default^[1]Bit 7

General Register Set^[2]

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

0

1

RHR

THR

IER

XX

00

bit 7

0

bit 6

0

bit 5

bit 4

bit 3

bit 2

bit 1

bit 0

low

power

mode

Sleep

mode

modem receive

status line

interrupt status

interrupt

XMIT

transmit receive

holding holding

register register

0

1

0

1

0

1

FCR

ISR

00

01

00

60

RCVR

trigger

(MSB)

RCVR

trigger

(LSB)

64-byte reserved DMA

FIFO

enable

RCVR

FIFO

reset

FIFO

enable

mode

select

FIFO

reset

FIFOs

64-byte

0

INT

priority

bit 2

INT

priority

bit 1

INT

priority

bit 0

INT

status

enabled enabled FIFO

enable

LCR

MCR

LSR

divisor

latch

enable

set break set parity even

parity

enable

stop bits word

length

word

length

bit 0

bit 1

0

reserved loop back OUT2,

OUT1

RTS

DTR

INT

enable

FIFO

data

error

trans.

empty

trans.

holding

empty

break

interrupt error

framing parity

overrun receive

error

data

ready

1

0

1

MSR

SPR

X0

FF

DCD

bit 7

RI

DSR

bit 5

CTS

bit 4

∆DCD

∆RI

∆DSR

∆CTS

bit 6

bit 3

bit 2

bit 1

bit 0

Special Register Set^[3]

0

DLL

XX

bit 7

bit 6

bit 5

bit 4

bit 3

bit 2

bit 1

bit 9

bit 0

bit 8

0

1

DLM

bit 15

bit 14

bit 13

bit 12

bit 11

bit 10

Enhanced Register Set^[4]

0

1

0

EFR 00

Auto

CTS

Auto RTS 0

0

[1] The value shown represents the register’s initialized HEX value; X = n/a.

[2] These registers are accessible only when LCR[7] = 0.

[3] The Special Register set is accessible only when LCR[7] is set to a logic 1.

[4] Enhanced Feature Register is accessible only when LCR is set to ‘BF_Hex’.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

16 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

7.1 Transmit (THR) and Receive (RHR) Holding Registers

The serial transmitter section consists of an 8-bit Transmit Hold Register (THR) and

Transmit Shift Register (TSR). The status of the THR is provided in the Line Status

Register (LSR). Writing to the THR transfers the contents of the data bus (D7-D0) to

the THR, providing that the THR or TSR is empty. The THR empty ﬂag in the LSR

register will be set to a logic 1 when the transmitter is empty or when data is

transferred to the TSR. Note that a write operation can be performed when the THR

empty ﬂag is set (logic 0 = FIFO full; logic 1 = at least one FIFO location available).

The serial receive section also contains an 8-bit Receive Holding Register (RHR).

Receive data is removed from the SC16C750 and receive FIFO by reading the RHR

register. The receive section provides a mechanism to prevent false starts. On the

falling edge of a start or false start bit, an internal receiver counter starts counting

clocks at the 16× clock rate. After 7-¹⁄₂clocks, the start bit time should be shifted to

the center of the start bit. At this time the start bit is sampled, and if it is still a logic 0

it is validated. Evaluating the start bit in this manner prevents the receiver from

assembling a false character. Receiver status codes will be posted in the LSR.

7.2 Interrupt Enable Register (IER)

The Interrupt Enable Register (IER) masks the interrupts from receiver ready,

transmitter empty, line status and modem status registers. These interrupts would

normally be seen on the INT output pin.

Table 9:

Interrupt Enable Register bits description

Description

Bit

Symbol

7-6

IER[7],

Not used.

IER[6]

IER[5]

5

4

3

Low power mode.

Logic 0 = Disable low power mode (normal default condition).

Logic 1 = Enable low power mode.

IER[4]

IER[3]

Sleep mode.

Logic 0 = Disable sleep mode (normal default condition).

Logic 1 = Enable sleep mode. See Section 6.7 “Sleep mode” for details.

Modem Status Interrupt.

Logic 0 = Disable the modem status register interrupt (normal default

condition).

Logic 1 = Enable the modem status register interrupt.

2

IER[2]

Receive Line Status interrupt. This interrupt will be issued whenever a fully

assembled receive character is transferred from RSR to the RHR/FIFO,

i.e., data ready, LSR[0].

Logic 0 = Disable the receiver line status interrupt (normal default

condition).

Logic 1 = Enable the receiver line status interrupt.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

17 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Table 9:

Interrupt Enable Register bits description…continued

Bit

Symbol Description

1

IER[1]

Transmit Holding Register interrupt. This interrupt will be issued whenever

the THR is empty, and is associated with LSR[1].

Logic 0 = Disable the transmitter empty interrupt (normal default

condition).

Logic 1 = Enable the transmitter empty interrupt.

0

IER[0]

Receive Holding Register interrupt. This interrupt will be issued when the

FIFO has reached the programmed trigger level, or is cleared when the

FIFO drops below the trigger level in the FIFO mode of operation.

Logic 0 = Disable the receiver ready interrupt (normal default condition).

Logic 1 = Enable the receiver ready interrupt.

7.2.1 IER versus Receive FIFO interrupt mode operation

When the receive FIFO (FCR[0] = logic 1), and receive interrupts (IER[0] = logic 1)

are enabled, the receive interrupts and register status will reﬂect the following:

• The receive data available interrupts are issued to the external CPU when the

FIFO has reached the programmed trigger level. It will be cleared when the FIFO

drops below the programmed trigger level.

• FIFO status will also be reﬂected in the user accessible ISR register when the

FIFO trigger level is reached. Both the ISR register status bit and the interrupt will

be cleared when the FIFO drops below the trigger level.

• The data ready bit (LSR[0]) is set as soon as a character is transferred from the

shift register to the receive FIFO. It is reset when the FIFO is empty.

7.2.2 IER versus Receive/Transmit FIFO polled mode operation

When FCR[0] = logic 1, resetting IER[0-3] enables the SC16C750 in the FIFO polled

mode of operation. Since the receiver and transmitter have separate bits in the LSR,

either or both can be used in the polled mode by selecting respective transmit or

receive control bit(s).

• LSR[0] will be a logic 1 as long as there is one byte in the receive FIFO.

• LSR[1-4] will provide the type of errors encountered, if any.

• LSR[5] will indicate when the transmit FIFO is empty.

• LSR[6] will indicate when both the transmit FIFO and transmit shift register are

empty.

• LSR[7] will indicate any FIFO data errors.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

18 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

7.3 FIFO Control Register (FCR)

This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO

trigger levels, and select the DMA mode.

7.3.1 DMA mode

Mode 0 (FCR bit 3 = 0): Set and enable the interrupt for each single transmit or

receive operation, and is similar to the 16C450 mode. Transmit Ready (TXRDY) will

go to a logic 0 whenever an empty transmit space is available in the Transmit Holding

Register (THR). Receive Ready (RXRDY) will go to a logic 0 whenever the Receive

Holding Register (RHR) is loaded with a character.

Mode 1 (FCR bit 3 = 1): Set and enable the interrupt in a block mode operation. The

transmit interrupt is set when the transmit FIFO is below the programmed trigger

level. The receive interrupt is set when the receive FIFO ﬁlls to the programmed

trigger level. However, the FIFO continues to ﬁll regardless of the programmed level

until the FIFO is full. RXRDY remains a logic 0 as long as the FIFO ﬁll level is above

the programmed trigger level.

7.3.2 FIFO mode

Table 10: FIFO Control Register bits description

Bit

Symbol

Description

7-6

FCR[7]

(MSB),

FCR[6]

(LSB)

RCVR trigger. These bits are used to set the trigger level for the receive

FIFO interrupt.

An interrupt is generated when the number of characters in the FIFO

equals the programmed trigger level. However, the FIFO will continue to

be loaded until it is full. Refer to Table 11.

5

FCR[5]

Logic 0 = 16-byte mode (normal default condition).

Logic 1 = 64-byte mode.

4

3

FCR[4]

FCR[3]

Reserved.

DMA mode select.

Logic 0 = Set DMA mode ‘0’ (normal default condition).

Logic 1 = Set DMA mode ‘1’

Transmit operation in mode ‘0’: When the SC16C750 is in the 16C450

mode (FIFOs disabled; FCR[0] = logic 0) or in the FIFO mode (FIFOs

enabled; FCR[0] = logic 1; FCR[3] = logic 0), and when there are no

characters in the transmit FIFO or transmit holding register, the TXRDY

pin will be a logic 0. Once active, the TXRDY pin will go to a logic 1 after

the ﬁrst character is loaded into the transmit holding register.

Receive operation in mode ‘0’: When the SC16C750 is in 16C450

mode, or in the FIFO mode (FCR[0] = logic 1; FCR[3] = logic 0) and

there is at least one character in the receive FIFO, the RXRDY pin will

be a logic 0. Once active, the RXRDY pin will go to a logic 1 when there

are no more characters in the receiver.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

19 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Table 10: FIFO Control Register bits description…continued

Bit

Symbol

Description

Transmit operation in mode ‘1’: When the SC16C750 is in FIFO mode

(FCR[0] = logic 1; FCR[3] = logic 1), the TXRDY pin will be a logic 1

when the transmit FIFO is completely full. It will be a logic 0 when the

trigger level has been reached.

Receive operation in mode ‘1’: When the SC16C750 is in FIFO mode

(FCR[0] = logic 1; FCR[3] = logic 1) and the trigger level has been

reached, or a Receive Time-Out has occurred, the RXRDY pin will go to

a logic 0. Once activated, it will go to a logic 1 after there are no more

characters in the FIFO.

2

1

0

FCR[2]

FCR[1]

FCR[0]

XMIT FIFO reset.

Logic 0 = No FIFO transmit reset (normal default condition).

Logic 1 = Clears the contents of the transmit FIFO and resets the

FIFO counter logic (the transmit shift register is not cleared or

altered). This bit will return to a logic 0 after clearing the FIFO.

RCVR FIFO reset.

Logic 0 = No FIFO receive reset (normal default condition).

Logic 1 = Clears the contents of the receive FIFO and resets the FIFO

counter logic (the receive shift register is not cleared or altered). This

bit will return to a logic 0 after clearing the FIFO.

FIFO enable.

Logic 0 = Disable the transmit and receive FIFO (normal default

condition).

Logic 1 = Enable the transmit and receive FIFO. This bit must be a

‘1’ when other FCR bits are written to, or they will not be

programmed.

Table 11: RCVR trigger levels

FCR[7]

FCR[6]

RX FIFO trigger level (bytes)

16-byte operation

64-byte operation

0

1

0

1

0

1

4

16

32

56

8

14

9397 750 11623

Product data

Rev. 04 — 20 June 2003

20 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

7.4 Interrupt Status Register (ISR)

The SC16C750 provides six levels of prioritized interrupts to minimize external

software interaction. The Interrupt Status Register (ISR) provides the user with six

interrupt status bits. Performing a read cycle on the ISR will provide the user with the

highest pending interrupt level to be serviced. No other interrupts are acknowledged

until the pending interrupt is serviced. Whenever the interrupt status register is read,

the interrupt status is cleared. However, it should be noted that only the current

pending interrupt is cleared by the read. A lower level interrupt may be seen after

re-reading the interrupt status bits. Table 12 “Interrupt source” shows the data values

(bits 0-5) for the six prioritized interrupt levels and the interrupt sources associated

with each of these interrupt levels.

Table 12: Interrupt source

Priority

level

ISR[3] ISR[2] ISR[1] ISR[0] Source of the interrupt

1

2

3

0

1

0

1

0

1

0

1

0

LSR (Receiver Line Status Register)

RXRDY (Received Data Ready)

RXRDY (Receive Data time-out)

TXRDY (Transmitter Holding Register

Empty)

4

0

MSR (Modem Status Register)

Table 13: Interrupt Status Register bits description

Bit

Symbol

Description

7-6

ISR[7-6]

FIFOs enabled. These bits are set to a logic 0 when the FIFO is

not being used. They are set to a logic 1 when the FIFOs are

enabled.

Logic 0 or cleared = default condition.

64-byte FIFO enable.

5

ISR[5]

Logic 0 = 16-byte operation.

Logic 1 = 64-byte operation.

Not used.

4

ISR[4]

3-1

ISR[3-1]

INT priority bits 2-0. These bits indicate the source for a pending

interrupt at interrupt priority levels 1, 2, and 3 (see Table 12).

Logic 0 or cleared = default condition.

INT status.

0

ISR[0]

Logic 0 = An interrupt is pending and the ISR contents may be

used as a pointer to the appropriate interrupt service routine.

Logic 1 = No interrupt pending (normal default condition).

9397 750 11623

Product data

Rev. 04 — 20 June 2003

21 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

7.5 Line Control Register (LCR)

The Line Control Register is used to specify the asynchronous data communication

format. The word length, the number of stop bits, and the parity are selected by

writing the appropriate bits in this register.

Table 14: Line Control Register bits description

Bit

Symbol

Description

7

LCR[7] ^[1]

Divisor latch enable. The internal baud rate counter latch and Enhance

Feature mode enable.

Logic 0 = Divisor latch disabled (normal default condition).

Logic 1 = Divisor latch and enhanced feature register enabled.

6

5

LCR[6]

LCR[5]

Set break. When enabled, the Break control bit causes a break condition

to be transmitted (the TX output is forced to a logic 0 state). This

condition exists until disabled by setting LCR[6] to a logic 0.

Logic 0 = no TX break condition (normal default condition).

Logic 1 = forces the transmitter output (TX) to a logic 0 for alerting the

remote receiver to a line break condition.

Set parity. If the parity bit is enabled, LCR[5] selects the forced parity

format. Programs the parity conditions (see Table 15).

Logic 0 = parity is not forced (normal default condition).

LCR[5] = logic 1 and LCR[4] = logic 0: parity bit is forced to a logical 1

for the transmit and receive data.

LCR[5] = logic 1 and LCR[4] = logic 1: parity bit is forced to a logical 0

for the transmit and receive data.

4

LCR[4]

Even parity. If the parity bit is enabled with LCR[3] set to a logic 1,

LCR[4] selects the even or odd parity format.

Logic 0 = ODD Parity is generated by forcing an odd number of

logic 1s in the transmitted data. The receiver must be programmed to

check the same format (normal default condition).

Logic 1 = EVEN Parity is generated by forcing an even number of

logic 1s in the transmitted data. The receiver must be programmed to

check the same format.

3

LCR[3]

Parity enable. Parity or no parity can be selected via this bit.

Logic 0 = no parity (normal default condition).

Logic 1 = a parity bit is generated during the transmission, receiver

checks the data and parity for transmission errors.

2

LCR[2]

Stop bits. The length of stop bit is speciﬁed by this bit in conjunction with

the programmed word length (see Table 16).

Logic 0 or cleared = default condition.

1-0

LCR[1-0]

Word length bits 1, 0. These two bits specify the word length to be

transmitted or received (see Table 17).

Logic 0 or cleared = default condition.

[1] When LCR[7] = 1, the general register set cannot be accessed until LCR[7] = 0.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

22 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Table 15: LCR[5] parity selection

LCR[5]

LCR[4]

LCR[3]

Parity selection

no parity

X

0

1

X

0

1

0

1

0

1

ODD parity

EVEN parity

force parity ‘1’

forced parity ‘0’

Table 16: LCR[2] stop bit length

LCR[2]

Word length

5, 6, 7, 8

5

Stop bit length (bit times)

0

1

1-¹⁄₂

6, 7, 8

2

Table 17: LCR[1-0] word length

LCR[1]

LCR[0]

Word length

0

1

0

1

0

1

5

6

7

8

9397 750 11623

Product data

Rev. 04 — 20 June 2003

23 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

7.6 Modem Control Register (MCR)

This register controls the interface with the modem or a peripheral device.

Table 18: Modem Control Register bits description

Bit

7

Symbol

MCR[7]

MCR[6]

MCR[5]

MCR[4]

Description

Reserved. Set to 0.

6

5

4

Loop-back. Enable the local loop-back mode (diagnostics). In this

mode the transmitter output (TX) and the receiver input (RX), CTS,

DSR, DCD, and RI are disconnected from the SC16C750 I/O pins.

Internally the modem data and control pins are connected into a

loop-back data conﬁguration (see Figure 5). In this mode, the receiver

and transmitter interrupts remain fully operational. The Modem

Control Interrupts are also operational, but the interrupts’ sources are

switched to the lower four bits of the Modem Control. Interrupts

continue to be controlled by the IER register.

Logic 0 = Disable loop-back mode (normal default condition).

Logic 1 = Enable local loop-back mode (diagnostics).

3

MCR[3]

OUT2, INTx enable. Used to control the modem DCD signal in the

loop-back mode.

Logic 0 = Forces INT output to the 3-State mode. In the loop-back

mode, sets OUT2 (DCD) internally to a logic 1.

Logic 1 = Forces the INT output to the active mode. In the

loop-back mode, sets OUT2 (DCD) internally to a logic 0.

2

1

MCR[2]

MCR[1]

OUT1. This bit is used in the Loop-back mode only. In the loop-back

mode, this bit is used to write the state of the modem RI interface

signal via OUT1.

RTS

Logic 0 = Force RTS output to a logic 1 (normal default condition).

Logic 1 = Force RTS output to a logic 0.

DTR

0

MCR[0]

Logic 0 = Force DTR output to a logic 1 (normal default condition).

Logic 1 = Force DTR output to a logic 0.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

24 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

7.7 Line Status Register (LSR)

This register provides the status of data transfers between the SC16C750 and

the CPU.

Table 19: Line Status Register bits description

Bit

Symbol

Description

7

LSR[7]

FIFO data error.

Logic 0 = No error (normal default condition).

Logic 1 = At least one parity error, framing error or break indication is in

the current FIFO data. This bit is cleared when LSR register is read.

6

5

LSR[6]

LSR[5]

THR and TSR empty. This bit is the Transmit Empty indicator. This bit is

set to a logic 1 whenever the transmit holding register and the transmit

shift register are both empty. It is reset to logic 0 whenever either the THR

or TSR contains a data character. In the FIFO mode, this bit is set to ‘1’

whenever the transmit FIFO and transmit shift register are both empty.

THR empty. This bit is the Transmit Holding Register Empty indicator.

This bit indicates that the UART is ready to accept a new character for

transmission. In addition, this bit causes the UART to issue an interrupt to

CPU when the THR interrupt enable is set. The THR bit is set to a logic 1

when a character is transferred from the transmit holding register into the

transmitter shift register. The bit is reset to a logic 0 concurrently with the

loading of the transmitter holding register by the CPU. In the FIFO mode,

this bit is set when the transmit FIFO is empty; it is cleared when at least

1 byte is written to the transmit FIFO.

4

3

2

1

LSR[4]

LSR[3]

LSR[2]

LSR[1]

Break interrupt.

Logic 0 = No break condition (normal default condition).

Logic 1 = The receiver received a break signal (RX was a logic 0 for

one character frame time). In the FIFO mode, only one break character

is loaded into the FIFO.

Framing error.

Logic 0 = No framing error (normal default condition).

Logic 1 = Framing error. The receive character did not have a valid stop

bit(s). In the FIFO mode, this error is associated with the character at

the top of the FIFO.

Parity error.

Logic 0 = No parity error (normal default condition).

Logic 1 = Parity error. The receive character does not have correct

parity information and is suspect. In the FIFO mode, this error is

associated with the character at the top of the FIFO.

Overrun error.

Logic 0 = No overrun error (normal default condition).

Logic 1 = Overrun error. A data overrun error occurred in the receive

shift register. This happens when additional data arrives while the FIFO

is full. In this case, the previous data in the shift register is overwritten.

Note that under this condition, the data byte in the receive shift register

is not transferred into the FIFO, therefore the data in the FIFO is not

corrupted by the error.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

25 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Table 19: Line Status Register bits description…continued

Bit

Symbol

Description

0

LSR[0]

Receive data ready.

Logic 0 = No data in receive holding register or FIFO (normal default

condition).

Logic 1 = Data has been received and is saved in the receive holding

register or FIFO.

7.8 Modem Status Register (MSR)

This register provides the current state of the control interface signals from the

modem, or other peripheral device to which the SC16C750 is connected. Four bits of

this register are used to indicate the changed information. These bits are set to a

logic 1 whenever a control input from the modem changes state. These bits are set to

a logic 0 whenever the CPU reads this register.

Table 20: Modem Status Register bits description

Bit

Symbol

Description

7

MSR[7]

Data Carrier Detect. DCD (Active-HIGH, logical 1). Normally this bit is

the complement of the DCD input. In the loop-back mode this bit is

equivalent to the OUT2 bit in the MCR register.

6

5

4

MSR[6]

MSR[5]

MSR[4]

Ring Indicator. RI (Active-HIGH, logical 1). Normally this bit is the

complement of the RI input. In the loop-back mode this bit is equivalent

to the OUT1 bit in the MCR register.

Data Set Ready. DSR (Active-HIGH, logical 1). Normally this bit is the

complement of the DSR input. In loop-back mode this bit is equivalent to

the DTR bit in the MCR register.

Clear To Send. CTS. CTS functions as hardware ﬂow control signal input

if it is enabled via EFR[7]. Flow control (when enabled) allows starting

and stopping the transmissions based on the external modem CTS

signal. A logic 1 at the CTS pin will stop SC16C750 transmissions as

soon as current character has ﬁnished transmission. Normally MSR[4] is

the complement of the CTS input. However, in the loop-back mode, this

bit is equivalent to the RTS bit in the MCR register.

3

2

MSR[3]

MSR[2]

∆DCD ^[1]

Logic 0 = No DCD change (normal default condition).

Logic 1 = The DCD input to the SC16C750 has changed state since

the last time it was read. A modem Status Interrupt will be generated.

∆RI ^[1]

Logic 0 = No RI change (normal default condition).

Logic 1 = The RI input to the SC16C750 has changed from a logic 0 to

a logic 1. A modem Status Interrupt will be generated.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

26 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Table 20: Modem Status Register bits description…continued

Bit

Symbol

Description

1

MSR[1]

∆DSR ^[1]

Logic 0 = No DSR change (normal default condition).

Logic 1 = The DSR input to the SC16C750 has changed state since

the last time it was read. A modem Status Interrupt will be generated.

0

MSR[0]

∆CTS ^[1]

Logic 0 = No CTS change (normal default condition).

Logic 1 = The CTS input to the SC16C750 has changed state since

the last time it was read. A modem Status Interrupt will be generated.

[1] Whenever any MSR bit 0-3 is set to logic 1, a Modem Status Interrupt will be generated.

7.9 Scratchpad Register (SPR)

The SC16C750 provides a temporary data register to store 8 bits of user information.

7.10 Enhanced Feature Register (EFR)

Enhanced features are enabled or disabled using this register.

Table 21: Enhanced Feature Register bits description

Bit

Symbol Description

7

EFR[7]

Automatic CTS ﬂow control.

Logic 0 = Automatic CTS ﬂow control is disabled (normal default

condition).

Logic 1 = Enable Automatic CTS ﬂow control. Transmission will stop

when CTS goes to a logical 1. Transmission will resume when the CTS

pin returns to a logical 0.

6

EFR[6]

Automatic RTS ﬂow control. Automatic RTS may be used for hardware ﬂow

control by enabling EFR[6]. When Auto-RTS is selected, an interrupt will

be generated when the receive FIFO is ﬁlled to the programmed trigger

level and RTS will go to a logic 1 at the next trigger level. RTS will return to

a logic 0 when data is unloaded below the next lower trigger level

(programmed trigger level 1). The state of this register bit changes with the

status of the hardware ﬂow control. RTS functions normally when

hardware ﬂow control is disabled.

0 = Automatic RTS ﬂow control is disabled (normal default condition).

1 = Enable Automatic RTS ﬂow control.

5-0

EFR[5-0] Reserved; set to 0.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

27 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

7.11 SC16C750 external reset conditions

Table 22: Reset state for registers

Register

IER

Reset state

IER[7-0] = 0

ISR

ISR[7-1] = 0; ISR[0] = 1

LCR[7-0] = 0

LCR

MCR

LSR

MCR[7-0] = 0

LSR[7] = 0; LSR[6-5] = 1; LSR[4-0] = 0

MSR[7-4] = input signals; MSR[3-0] = 0

FCR[7-0] = 0

MSR

FCR

EFR

EFR[7-0] = 0

Table 23: Reset state for outputs

Output

TX

Reset state

HIGH

RTS

HIGH

DTR

HIGH

RXRDY

TXRDY

INT

HIGH (STD mode)

LOW (STD mode)

8. Limiting values

Table 24: Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol

V_CC

Parameter

Conditions

Min

Max

Unit

V

supply voltage

-

7

V_n

voltage at any pin

operating temperature

storage temperature

GND − 0.3 V_CC+ 0.3

V

T_amb

−40

−65

-

+85

°C

mW

T_stg

+150

500

P_tot(pack)

total power dissipation per

package

9397 750 11623

Product data

Rev. 04 — 20 June 2003

28 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

9. Static characteristics

Table 25: DC electrical characteristics

T_amb= −40 °C to +85 °C; V_CC= 2.5V, 3.3 V or 5.0 V ±10%, unless otherwise speciﬁed.

Symbol Parameter

Conditions

2.5 V

Max

3.3 V

Max

5.0 V

Max

Unit

Min

−0.3

1.8

−0.3

1.6

-

Min

−0.3

2.4

−0.3

2.0

-

Min

−0.5

3.0

−0.5

2.2

-

V_IL(CK)

V_IH(CK)

V_IL

LOW-level clock input voltage

0.45

V_CC

0.65

-

0.6

V_CC

0.8

-

0.6

V

HIGH-level clock input voltage

LOW-level input voltage

HIGH-level input voltage

V_CC

0.8

V_IH

V_CC

0.4

V_OL

LOW-level output voltage on all I_OL= 5 mA

outputs^[1]

-

(databus)

_OL= 4 mA

(other outputs)

_OL= 2 mA

(databus)

_OL= 1.6 mA

I

-

0.4

-

V

I

-

0.4

-

I

-

0.4

-

(other outputs)

V_OH

HIGH-level output voltage

I_OH= −5 mA

(databus)

-

2.4

I

_OH= −1 mA

(other outputs)

_OH= −800 µA

(databus)

_OH= −400 µA

(other outputs)

-

2.0

-

I

1.85

-

I

I_LIL

LOW-level input leakage current

clock leakage

-

±10

±30

3.5

5

-

±10

±30

4.5

5

-

±10

±30

4.5

5

µA

mA

pF

kΩ

I_CL

-

I_CC

average power supply current

-

C_i

input capacitance

internal pull-up resistance^[2]

-

R_pu(int)

500

-

500

-

500

-

[1] Except for x₂, V_OL= 1 V typically.

[2] Refer to Table 2 “Pin description” on page 5 for a listing of pins having internal pull-up resistors.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

29 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

10. Dynamic characteristics

Table 26: AC electrical characteristics

T_amb= −40 °C to +85 °C; V_CC= 2.5 V, 3.3 V or 5 V ±10%, unless otherwise speciﬁed.

Symbol

Parameter

Conditions

2.5 V

3.3 V

5.0 V

Unit

Min Max

t_1w, t_2w

t_3w

clock pulse duration

oscillator/clock frequency

address strobe width

address set-up time

address hold time

15

-

13

-

10

-

ns

MHz

ns

[1]

16

32

-

48

-

t_4w

45

5

-

35

5

25

1

t_5s

-

t_5h

5

-

5

-

5

-

t_6s

chip select set-up time to AS

address hold time

10

0

-

5

-

0

-

t_6h

-

0

-

0

-

[2]

t_6s'

address set-up time

chip select hold time

IOR delay from chip select

IOR strobe width

10

0

-

10

0

-

5

-

t_6h

-

0

-

t_7d

10

77

0

-

10

26

0

-

10

23

0

-

t_7w

25 pF load

-

t_7h

chip select hold time from IOR

address hold time

-

[2]

t_7h'

5

-

5

-

5

-

t_8d

IOR delay from address

read cycle delay

10

20

-

10

20

-

10

20

-

t_9d

25 pF load

-

t_11d

t_12d

t_12h

t_13d

t_13w

t_13h

t_14d

t_15d

t_16s

t_16h

t_17d

t_18d

IOR to DDIS delay

100

35

26

15

-

30

23

15

-

delay from IOR to data

data disable time

-

77

-

15

-

IOW delay from chip select

IOW strobe width

10

20

0

-

10

20

0

10

15

0

[3]

[4]

-

chip select hold time from IOW

IOW delay from address

write cycle delay

-

10

25

20

15

-

10

25

20

5

-

10

20

15

5

-

data set-up time

-

data hold time

-

delay from IOW to output

25 pF load

100

-

33

24

-

29

23

delay to set interrupt from Modem

input

-

t_19d

t_20d

t_21d

t_22d

t_23d

t_24d

t_25d

t_26d

t_27d

delay to reset interrupt from IOR

delay from stop to set interrupt

delay from IOR to reset interrupt

delay from start to set interrupt

delay from IOW to transmit start

delay from IOW to reset interrupt

delay from stop to set RXRDY

delay from IOR to reset RXRDY

delay from IOW to set TXRDY

25 pF load

-

8

-

100

1

-

8

-

24

1

-

8

-

23

1

ns

R_clk

ns

100

24

29

45

24

45

1

28

40

24

40

1

ns

R_clk

ns

100

1

R_clk

ns

100

45

40

ns

9397 750 11623

Product data

Rev. 04 — 20 June 2003

30 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Table 26: AC electrical characteristics…continued

T_amb= −40 °C to +85 °C; V_CC= 2.5 V, 3.3 V or 5 V ±10%, unless otherwise speciﬁed.

Symbol

Parameter

Conditions

2.5 V

3.3 V

5.0 V

Unit

Min Max

t_28d

t_RESET

N

delay from start to reset TXRDY

Reset pulse width

-

8

-

8

-

8

R_clk

ns

100

1

-

40

1

-

40

1

-

baud rate divisor

2¹⁶− 1

2¹⁶− 1 R_clk

[1] Applies to external clock, crystal oscillator max 24 MHz.

[2] Applicable only when AS is tied LOW.

1

[3] IOWstrobe_max

=

--------------------------------------

2(Baudrate_max

)

= 333 ns (for Baudrate_max= 1.5 Mbits/s)

= 1 µs (for Baudrate_max= 460.8 kbits/s)

= 4 µs (for Baudrate_max= 115.2 kbits/s)

[4] When in both DMA mode 0 and FIFO enable mode, the write cycle delay should be larger than one x₁clock cycle.

10.1 Timing diagrams

t

4w

AS

t

5s

t

5h

VALID

ADDRESS

A0–A2

t

6s

t

6h

CS2

CS1–CS0

VALID

t

7d

t

7h

t

7w

t

8d

t

9d

IOR, IOR

ACTIVE

t

11d

t

11d

DDIS

ACTIVE

t

12h

12d

D0–D7

DATA

002aaa331

Fig 6. General read timing when using AS signal.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

31 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

t

4w

AS

t

5s

t

5h

VALID

ADDRESS

A0–A2

t

6s

t

6h

CS2

CS1–CS0

VALID

t

13h

13d

t

13w

t

15d

14d

IOW, IOW

ACTIVE

t

16h

16s

D0–D7

DATA

002aaa332

Fig 7. General write timing when using AS signal.

VALID

ADDRESS

VALID

ADDRESS

A0–A2

t

′

7h

t

′

6s

t

′

7h

t

′

6s

t

7w

ACTIVE

CS

t

7w

t

9d

IOR

ACTIVE

t

12h

t

12h

12d

D0–D7

DATA

002aaa333

Fig 8. General read timing when AS is tied to GND.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

32 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

VALID

ADDRESS

VALID

ADDRESS

A0–A2

t

′

7h

t

′

6s

t

′

7h

t

′

6s

ACTIVE

CS

t

13w

15d

IOW

ACTIVE

t

16h

t

16h

16s

D0–D7

DATA

002aaa334

Fig 9. General write timing when AS is tied to GND.

IOW

ACTIVE

t

17d

RTS

DTR

CHANGE OF STATE

DCD

CTS

DSR

CHANGE OF STATE

t

18d

INT

ACTIVE

t

19d

IOR

ACTIVE

t

18d

RI

CHANGE OF STATE

002aaa111

Fig 10. Modem input/output timing.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

33 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

t

1w

2w

EXTERNAL

CLOCK

002aaa112

t

3w

Fig 11. External clock timing.

START

BIT

PARITY STOP START

BIT

DATA BITS (5-8)

RX

D0

D1

D2

D3

D4

D5

D6

D7

5 DATA BITS

6 DATA BITS

7 DATA BITS

t

20d

ACTIVE

INT

t

21d

ACTIVE

IOR

16 BAUD RATE CLOCK

002aaa113

Fig 12. Receive timing.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

34 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

START

BIT

PARITY STOP START

BIT

DATA BITS (5–8)

RX

D0

D1

D2

D3

D4

D5

D6

D7

t

25d

ACTIVE

DATA

READY

RXRDY

t

26d

ACTIVE

IOR

002aaa114

Fig 13. Receive ready timing in non-FIFO mode.

START

BIT

PARITY STOP

BIT BIT

DATA BITS (5–8)

RX

D0

D1

D2

D3

D4

D5

D6

D7

FIRST BYTE THAT

REACHES THE

TRIGGER LEVEL

t

25d

ACTIVE

DATA

READY

RXRDY

t

26d

ACTIVE

IOR

002aaa115

Fig 14. Receive ready timing in FIFO mode.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

35 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

START

BIT

PARITY STOP START

BIT

DATA BITS (5–8)

TX

D0

D1

D2

D3

D4

D5

D6

D7

5 DATA BITS

6 DATA BITS

7 DATA BITS

ACTIVE TX READY

INT

t

22d

t

24d

t

23d

ACTIVE

IOW

16 BAUD RATE CLOCK

002aaa116

Fig 15. Transmit timing.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

36 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

START

BIT

PARITY STOP START

BIT

DATA BITS (5–8)

TX

D0

D1

D2

D3

D4

D5

D6

D7

ACTIVE

IOW

D0–D7

TXRDY

TRANSMITTER READY

BYTE #1

t

28d

t

27d

ACTIVE

TRANSMITTER

NOT READY

002aaa129

Fig 16. Transmit ready timing in non-FIFO mode.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

37 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

START

BIT

PARITY STOP

BIT BIT

DATA BITS (5-8)

TX

D0

D1

D2

D3

D4

D5

D6

D7

5 DATA BITS

6 DATA BITS

7 DATA BITS

ACTIVE

IOW

D0–D7

TXRDY

t

28d

BYTE #16

t

27d

FIFO FULL

002aaa118

Fig 17. Transmit ready timing in FIFO mode (DMA mode ‘1’).

9397 750 11623

Product data

Rev. 04 — 20 June 2003

38 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

11. Package outline

PLCC44: plastic leaded chip carrier; 44 leads

SOT187-2

e

E

D

y

X

A

39

29

b

p

Z

E

28

40

b

1

w

M

44

1

H

E

pin 1 index

A

1

A

4

e

(A )

3

6

18

β

L

p

k

detail X

7

17

v

M

A

e

Z

D

B

H

v

M

B

D

0

5

10 mm

scale

DIMENSIONS (mm dimensions are derived from the original inch dimensions)

(1)

A

Z

E

4

1

(1)

D

UNIT

mm

A

b

D

E

e

H

k

L

p

v

w

y

β

b

3

1

D

E

D

E

p

max.

min.

max. max.

4.57

4.19

0.81 16.66 16.66

0.66 16.51 16.51

16.00 16.00 17.65 17.65 1.22 1.44

14.99 14.99 17.40 17.40 1.07 1.02

0.53

0.33

0.51 0.25 3.05

0.02 0.01 0.12

1.27

0.05

0.18 0.18

0.1

2.16 2.16

o

45

0.180

0.165

0.032 0.656 0.656

0.026 0.650 0.650

0.63 0.63 0.695 0.695 0.048 0.057

0.59 0.59 0.685 0.685 0.042 0.040

0.021

0.013

inches

0.007 0.007 0.004 0.085 0.085

Note

1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.

REFERENCES

OUTLINE

EUROPEAN

PROJECTION

ISSUE DATE

VERSION

IEC

JEDEC

JEITA

99-12-27

01-11-14

SOT187-2

112E10

MS-018

EDR-7319

Fig 18. PLCC44 (SOT187-2).

9397 750 11623

Product data

Rev. 04 — 20 June 2003

39 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

LQFP64: plastic low profile quad flat package; 64 leads; body 10 x 10 x 1.4 mm

SOT314-2

y

X

A

48

33

Z

49

32

E

e

H

A

E

2

E

A

(A )

3

A

1

w M

p

θ

b

L

p

pin 1 index

L

64

17

detail X

1

16

Z

v

M

A

D

e

w M

b

p

D

B

H

v

M

B

D

0

2.5

5 mm

scale

DIMENSIONS (mm are the original dimensions)

A

(1)

UNIT

A

b

c

D

E

e

H

L

v

w

y

Z

E

θ

1

2

3

p

D

E

p

D

max.

7^o

0^o

0.20 1.45

0.05 1.35

0.27 0.18 10.1 10.1

0.17 0.12 9.9 9.9

12.15 12.15

11.85 11.85

0.75

0.45

1.45 1.45

1.05 1.05

1.6

mm

0.25

0.5

1

0.2 0.12 0.1

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

REFERENCES

OUTLINE

EUROPEAN

PROJECTION

ISSUE DATE

VERSION

IEC

JEDEC

JEITA

00-01-19

03-02-25

SOT314-2

136E10

MS-026

Fig 19. LQFP64 (SOT314-2).

9397 750 11623

Product data

Rev. 04 — 20 June 2003

40 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

12. Soldering

12.1 Introduction to soldering surface mount packages

This text gives a very brief insight to a complex technology. A more in-depth account

of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit

Packages (document order number 9398 652 90011).

There is no soldering method that is ideal for all IC packages. Wave soldering can still

be used for certain surface mount ICs, but it is not suitable for ﬁne pitch SMDs. In

these situations reﬂow soldering is recommended. In these situations reﬂow

soldering is recommended.

12.2 Reﬂow soldering

Reﬂow soldering requires solder paste (a suspension of ﬁne solder particles, ﬂux and

binding agent) to be applied to the printed-circuit board by screen printing, stencilling

or pressure-syringe dispensing before package placement. Driven by legislation and

environmental forces the worldwide use of lead-free solder pastes is increasing.

Several methods exist for reﬂowing; for example, convection or convection/infrared

heating in a conveyor type oven. Throughput times (preheating, soldering and

cooling) vary between 100 and 200 seconds depending on heating method.

Typical reﬂow peak temperatures range from 215 to 270 °C depending on solder

paste material. The top-surface temperature of the packages should preferably be

kept:

• below 220 °C (SnPb process) or below 245 °C (Pb-free process)

– for all BGA and SSOP-T packages

– for packages with a thickness ≥ 2.5 mm

– for packages with a thickness < 2.5 mm and a volume ≥ 350 mm³so called

thick/large packages.

• below 235 °C (SnPb process) or below 260 °C (Pb-free process) for packages with

a thickness < 2.5 mm and a volume < 350 mm³so called small/thin packages.

Moisture sensitivity precautions, as indicated on packing, must be respected at all

times.

12.3 Wave soldering

Conventional single wave soldering is not recommended for surface mount devices

(SMDs) or printed-circuit boards with a high component density, as solder bridging

and non-wetting can present major problems.

To overcome these problems the double-wave soldering method was speciﬁcally

developed.

If wave soldering is used the following conditions must be observed for optimal

results:

• Use a double-wave soldering method comprising a turbulent wave with high

upward pressure followed by a smooth laminar wave.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

41 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

• For packages with leads on two sides and a pitch (e):

– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be

parallel to the transport direction of the printed-circuit board;

– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the

transport direction of the printed-circuit board.

The footprint must incorporate solder thieves at the downstream end.

• For packages with leads on four sides, the footprint must be placed at a 45° angle

to the transport direction of the printed-circuit board. The footprint must

incorporate solder thieves downstream and at the side corners.

During placement and before soldering, the package must be ﬁxed with a droplet of

adhesive. The adhesive can be applied by screen printing, pin transfer or syringe

dispensing. The package can be soldered after the adhesive is cured.

Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250 °C or

265 °C, depending on solder material applied, SnPb or Pb-free respectively.

A mildly-activated ﬂux will eliminate the need for removal of corrosive residues in

most applications.

12.4 Manual soldering

Fix the component by ﬁrst soldering two diagonally-opposite end leads. Use a low

voltage (24 V or less) soldering iron applied to the ﬂat part of the lead. Contact time

must be limited to 10 seconds at up to 300 °C.

When using a dedicated tool, all other leads can be soldered in one operation within

2 to 5 seconds between 270 and 320 °C.

12.5 Package related soldering information

Table 27: Suitability of surface mount IC packages for wave and reﬂow soldering

methods

Package^[1]

Soldering method

Wave

Reﬂow^[2]

BGA, LBGA, LFBGA, SQFP, SSOP-T^[3],

TFBGA, VFBGA

not suitable

suitable

DHVQFN, HBCC, HBGA, HLQFP, HSQFP,

HSOP, HTQFP, HTSSOP, HVQFN, HVSON,

SMS

not suitable^[4]

suitable

PLCC^[5], SO, SOJ

suitable

LQFP, QFP, TQFP

not recommended^[5][6]

not recommended^[7]

SSOP, TSSOP, VSO, VSSOP

[1] For more detailed information on the BGA packages refer to the (LF)BGA Application Note

(AN01026); order a copy from your Philips Semiconductors sales ofﬁce.

[2] All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the

maximum temperature (with respect to time) and body size of the package, there is a risk that internal

or external package cracks may occur due to vaporization of the moisture in them (the so called

popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated

Circuit Packages; Section: Packing Methods.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

42 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

[3] These transparent plastic packages are extremely sensitive to reﬂow soldering conditions and must

on no account be processed through more than one soldering cycle or subjected to infrared reﬂow

soldering with peak temperature exceeding 217 °C ± 10 °C measured in the atmosphere of the reﬂow

oven. The package body peak temperature must be kept as low as possible.

[4] These packages are not suitable for wave soldering. On versions with the heatsink on the bottom

side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with

the heatsink on the top side, the solder might be deposited on the heatsink surface.

[5] If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave

direction. The package footprint must incorporate solder thieves downstream and at the side corners.

[6] Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it

is deﬁnitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.

[7] Wave soldering is suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than

0.65 mm; it is deﬁnitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.

13. Revision history

Table 28: Revision history

Rev Date

CPCN

-

Description

04 20030620

Product data (9397 750 11623); ECN 853-2367 30035 of 16 June 2003.

Modiﬁcations:

• Figure 4 “Crystal oscillator connection.” on page 12: changed capacitors’ values and

added connection with resistor.

03 20030314

02 20021211

01 20020904

-

Product data (9397 750 11203); ECN 853-2367 29619 of 07 March 2003.

Product data (9397 750 10797); ECN 853-2367 29261 of 06 December 2002.

Product data (9397 750 10149); ECN 853-2367 28865 of 04 September 2002.

9397 750 11623

Product data

Rev. 04 — 20 June 2003

43 of 45

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

14. Data sheet status

Level Data sheet status^[1]

Product status^[2][3]

Deﬁnition

I

Objective data

Development

This data sheet contains data from the objective speciﬁcation for product development. Philips

Semiconductors reserves the right to change the speciﬁcation in any manner without notice.

II

Preliminary data

Qualiﬁcation

This data sheet contains data from the preliminary speciﬁcation. Supplementary data will be published

at a later date. Philips Semiconductors reserves the right to change the speciﬁcation without notice, in

order to improve the design and supply the best possible product.

III

Product data

Production

This data sheet contains data from the product speciﬁcation. Philips Semiconductors reserves the

right to make changes at any time in order to improve the design, manufacturing and supply. Relevant

changes will be communicated via a Customer Product/Process Change Notiﬁcation (CPCN).

[1]

[2]

Please consult the most recently issued data sheet before initiating or completing a design.

The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at

URL http://www.semiconductors.philips.com.

[3]

For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.

15. Deﬁnitions

16. Disclaimers

Short-form speciﬁcation — The data in a short-form speciﬁcation is

extracted from a full data sheet with the same type number and title. For

detailed information see the relevant data sheet or data handbook.

Life support — These products are not designed for use in life support

appliances, devices, or systems where malfunction of these products can

reasonably be expected to result in personal injury. Philips Semiconductors

customers using or selling these products for use in such applications do so

at their own risk and agree to fully indemnify Philips Semiconductors for any

damages resulting from such application.

Limiting values deﬁnition — Limiting values given are in accordance with

the Absolute Maximum Rating System (IEC 60134). Stress above one or

more of the limiting values may cause permanent damage to the device.

These are stress ratings only and operation of the device at these or at any

other conditions above those given in the Characteristics sections of the

speciﬁcation is not implied. Exposure to limiting values for extended periods

may affect device reliability.

Right to make changes — Philips Semiconductors reserves the right to

make changes in the products - including circuits, standard cells, and/or

software - described or contained herein in order to improve design and/or

performance. When the product is in full production (status ‘Production’),

relevant changes will be communicated via a Customer Product/Process

Change Notiﬁcation (CPCN). Philips Semiconductors assumes no

responsibility or liability for the use of any of these products, conveys no

licence or title under any patent, copyright, or mask work right to these

products, and makes no representations or warranties that these products are

free from patent, copyright, or mask work right infringement, unless otherwise

speciﬁed.

Application information — Applications that are described herein for any

of these products are for illustrative purposes only. Philips Semiconductors

make no representation or warranty that such applications will be suitable for

the speciﬁed use without further testing or modiﬁcation.

Contact information

For additional information, please visit http://www.semiconductors.philips.com.

For sales ofﬁce addresses, send e-mail to: sales.addresses@www.semiconductors.philips.com.

Fax: +31 40 27 24825

44 of 45

9397 750 11623

Product data

Rev. 04 — 20 June 2003

SC16C750

UART with 64-byte FIFO

Philips Semiconductors

Contents

1

2

3

4

General description . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Ordering information. . . . . . . . . . . . . . . . . . . . . 2

Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3

8

Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 28

Static characteristics . . . . . . . . . . . . . . . . . . . 29

Dynamic characteristics. . . . . . . . . . . . . . . . . 30

Timing diagrams. . . . . . . . . . . . . . . . . . . . . . . 31

Package outline . . . . . . . . . . . . . . . . . . . . . . . . 39

9

10

10.1

11

12

12.1

5

5.1

5.2

Pinning information. . . . . . . . . . . . . . . . . . . . . . 4

Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5

Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Introduction to soldering surface mount

packages. . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Reﬂow soldering. . . . . . . . . . . . . . . . . . . . . . . 41

Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . 41

Manual soldering . . . . . . . . . . . . . . . . . . . . . . 42

Package related soldering information. . . . . . 42

6

Functional description . . . . . . . . . . . . . . . . . . . 9

Internal registers. . . . . . . . . . . . . . . . . . . . . . . . 9

FIFO operation . . . . . . . . . . . . . . . . . . . . . . . . 10

Hardware ﬂow control. . . . . . . . . . . . . . . . . . . 11

Time-out interrupts . . . . . . . . . . . . . . . . . . . . . 11

Programmable baud rate generator . . . . . . . . 12

DMA operation . . . . . . . . . . . . . . . . . . . . . . . . 13

Sleep mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Loop-back mode. . . . . . . . . . . . . . . . . . . . . . . 14

12.2

12.3

12.4

12.5

6.1

6.2

6.3

6.4

6.5

6.6

6.7

6.8

13

14

15

16

Revision history . . . . . . . . . . . . . . . . . . . . . . . 43

Data sheet status. . . . . . . . . . . . . . . . . . . . . . . 44

Deﬁnitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

7

7.1

Register descriptions . . . . . . . . . . . . . . . . . . . 16

Transmit (THR) and Receive (RHR)

Holding Registers . . . . . . . . . . . . . . . . . . . . . 17

Interrupt Enable Register (IER) . . . . . . . . . . . 17

IER versus Receive FIFO interrupt

7.2

7.2.1

mode operation . . . . . . . . . . . . . . . . . . . . . . . 18

IER versus Receive/Transmit FIFO polled

7.2.2

mode operation . . . . . . . . . . . . . . . . . . . . . . . 18

FIFO Control Register (FCR) . . . . . . . . . . . . . 19

DMA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

FIFO mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Interrupt Status Register (ISR) . . . . . . . . . . . . 21

Line Control Register (LCR) . . . . . . . . . . . . . . 22

Modem Control Register (MCR) . . . . . . . . . . . 24

Line Status Register (LSR). . . . . . . . . . . . . . . 25

Modem Status Register (MSR). . . . . . . . . . . . 26

Scratchpad Register (SPR) . . . . . . . . . . . . . . 27

Enhanced Feature Register (EFR) . . . . . . . . . 27

SC16C750 external reset conditions . . . . . . . 28

7.3

7.3.1

7.3.2

7.4

7.5

7.6

7.7

7.8

7.9

7.10

7.11

Printed in the U.S.A

All rights are reserved. Reproduction in whole or in part is prohibited without the prior

written consent of the copyright owner.

The information presented in this document does not form part of any quotation or

contract, is believed to be accurate and reliable and may be changed without notice. No

liability will be accepted by the publisher for any consequence of its use. Publication

thereof does not convey nor imply any license under patent- or other industrial or

intellectual property rights.

Date of release: 20 June 2003

Document order number: 9397 750 11623


型号：	SC16C750IA44
厂家：	NXP
描述：	Universal Asynchronous Receiver/Transmitter (UART) with 64-byte FIFO 通用异步接收器/发送器（ UART ）具有64字节FIFO 外围集成电路先进先出芯片
文件：	总45页 (文件大小：548K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

SC16C750IA44 [NXP]

相关型号：

SC16C750IA44,512

SC16C750IA44,518

SC16C750IA44,529

SC16C750IB64

SC16C750IB64

SC16C750IB64,128

SC16C750IB64,151

SC16C750IB64,157

SC16C751B

SC16C751BIBS

SC16C751BIBS,115

SC16C751BIBS,128