PIP3121-A [PHILIPS]
Power Field-Effect Transistor, N-Channel, Metal-oxide Semiconductor FET;型号: | PIP3121-A |
厂家: | PHILIPS SEMICONDUCTORS |
描述: | Power Field-Effect Transistor, N-Channel, Metal-oxide Semiconductor FET 局域网 驱动 接口集成电路 |
文件: | 总7页 (文件大小:43K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Philips Semiconductors
Product specification
Logic level TOPFET
PIP3121-A
DESCRIPTION
QUICK REFERENCE DATA
Monolithic logic level protected
power MOSFET using TOPFET2
technology assembled in a 5 pin
surface mounting plastic package.
SYMBOL
PARAMETER
MAX.
UNIT
VDS
ID
Ptot
Tj
Continuous drain source voltage
Continuous drain current
Total power dissipation
Continuous junction temperature
Drain-source on-state resistance
50
40
107
150
20
V
A
W
˚C
mΩ
APPLICATIONS
RDS(ON)
General purpose switch for driving
lamps
SYMBOL
PARAMETER
NOM.
UNIT
motors
solenoids
heaters
VPS
Protection supply voltage
5
V
FEATURES
FUNCTIONAL BLOCK DIAGRAM
TrenchMOS output stage with
low on-state resistance
Separate input pin for higher
frequency drive
PROTECTION SUPPLY
DRAIN
5 V logic compatible input
Separate supply pin for logic
and protection circuits with low
operating current
FLAG
OC LOAD
O/V
DETECT
CLAMP
POWER
Overtemperature protection
Drain current limiting
INPUT
MOSFET
RIG
Short circuit load protection
Latched overload trip state reset
by the protection pin
Diagnostic flag pin indicates
protection supply connected,
overtemperature condition,overload
tripped state, or open circuit load
(detected in the off-state)
ESD protection on all pins
Overvoltage clamping
LOGIC AND
PROTECTION
SOURCE
Fig.1. Elements of the TOPFET.
PINNING - SOT263B-01
PIN CONFIGURATION
SYMBOL
PIN
1
DESCRIPTION
mb
mb
D
S
input
flag
TOPFET
2
P
F
I
P
3
drain
4
protection supply
source
1 2 3 4 5
Front view
MBL267
5
Fig. 2.
Fig. 3.
mb drain
October 2002
1
Rev 1.000
Philips Semiconductors
Product specification
Logic level TOPFET
PIP3121-A
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum Rating System (IEC 134)
SYMBOL PARAMETER
Continuous voltage
CONDITIONS
MIN.
MAX.
UNIT
V
VDS
Drain source voltage1
Continuous currents
Drain current
VIS = 0 V
-
-
50
ID
VPS = 5 V; Tmb =25˚C
VPS = 0 V; Tmb =80˚C
self -
limited
40
5
5
5
A
-
A
II
IF
IP
Input current
-5
-5
-5
mA
mA
mA
Flag current
Protection supply current
Thermal
Ptot
Total power dissipation
Tmb = 25˚C
-
107
W
Tstg
Tj
Tsold
Storage temperature
-55
-
-
175
150
260
˚C
˚C
˚C
Junction temperature2
Mounting base temperature
continuous
during soldering
ESD LIMITING VALUE
SYMBOL PARAMETER
CONDITIONS
MIN.
MAX.
UNIT
VC
Electrostatic discharge capacitor
voltage
Human body model;
C = 250 pF; R = 1.5 kΩ
-
2
kV
OVERLOAD PROTECTION LIMITING VALUE
With an adequate protection supply
connected, TOPFET can protect
itself from two types of overload -
overtemperature and short circuit
load.
For overload conditions an n-MOS
The drain current is limited to
reduce dissipation in case of short
circuit load. Refer to OVERLOAD
CHARACTERISTICS.
transistor turns on between the
input and source to quickly
discharge the power MOSFET
gate capacitance.
SYMBOL PARAMETER
Overload protection3
REQUIRED CONDITION
protection supply
PS ≥ 4 V
MIN.
MAX.
UNIT
VDS
Drain source voltage
V
0
35
V
OVERVOLTAGE CLAMPING LIMITING VALUES
At a drain source voltage above 50 V the power MOSFET is actively turned on to clamp overvoltage transients.
SYMBOL PARAMETER
Inductive load turn off
CONDITIONS
IDM = 25 A; VDD ≤ 20 V
Tmb = 25˚C
MIN.
MAX.
UNIT
EDSM
EDRM
Non-repetitive clamping energy
Repetitive clamping energy
-
-
550
60
mJ
mJ
Tmb ≤ 95˚C; f = 250 Hz
1 Prior to the onset of overvoltage clamping. For voltages above this value, safe operation is limited by the overvoltage clamping energy.
2 A higher Tj is allowed as an overload condition but at the threshold Tj(TO) the over temperature trip operates to protect the switch.
3 All control logic and protection functions are disabled during conduction of the source drain diode. If the protection circuit was previously
latched, it would be reset by this condition.
October 2002
2
Rev 1.000
Philips Semiconductors
Product specification
Logic level TOPFET
PIP3121-A
THERMAL CHARACTERISTIC
SYMBOL PARAMETER
Thermal resistance
CONDITIONS
MIN. TYP. MAX. UNIT
Rth j-mb
Junction to mounting base
-
-
0.94
1.17
K/W
OUTPUT CHARACTERISTICS
Limits are for -40˚C ≤ Tmb ≤ 150˚C; typicals are for Tmb = 25˚C unless otherwise specified.
SYMBOL PARAMETER
Off-state
CONDITIONS
MIN. TYP. MAX. UNIT
VIS = 0 V
V(CL)DSS
Drain-source clamping voltage ID = 10 mA
IDM = 5 A; tp ≤ 300 µs; δ ≤ 0.01
VPS = 0 V; VDS = 40 V
50
50
-
70
70
V
V
60
IDSS
Drain source leakage current1
-
-
-
100
10
µA
µA
Tmb = 25˚C
0.1
On-state
tp ≤ 300 µs; δ ≤ 0.01; VPS ≥ 4 V
RDS(ON)
Drain-source resistance
IDM = 15 A; VIS ≥ 4.4 V
-
-
-
15
40
20
mΩ
mΩ
Tmb = 25˚C
INPUT CHARACTERISTICS
Limits are for -40˚C ≤ Tmb ≤ 150˚C; typicals are for Tmb = 25˚C unless otherwise specified.
SYMBOL PARAMETER
Normal operation
CONDITIONS
MIN. TYP. MAX. UNIT
VIS(TO)
Input threshold voltage2
ID = 1 mA
0.6
1.1
-
2.6
2.1
V
V
Tmb = 25˚C
1.6
IIS
Input current
VIS = 5 V
II = 1 mA
-
5.5
-
16
6.4
1.7
100
8.5
-
µA
V
V(CL)IS
RIG
Input clamping voltage
Internal series resistance3
Overload protection latched
Input current
to gate of power MOSFET
PS ≥ 4 V
VIS = 5 V
kΩ
V
IISL
1
2.7
4
mA
1 The drain current required for open circuit load detection is switched off when there is no protection supply, in order to ensure a low off-state
quiescent current. Refer to OPEN CIRCUIT LOAD DETECTION CHARACTERISTICS.
2 The measurement method is simplified if VPS = 0 V, in order to distinguish ID from IDSP. Refer to OPEN CIRCUIT LOAD DETECTION
CHARACTERISTICS.
3 This is not a directly measurable parameter.
October 2002
3
Rev 1.000
Philips Semiconductors
Product specification
Logic level TOPFET
PIP3121-A
PROTECTION SUPPLY CHARACTERISTICS
Limits are for -40˚C ≤ Tmb ≤ 150˚C; typicals are for Tmb = 25˚C.
SYMBOL PARAMETER
Protection & detection
Threshold voltage1
CONDITIONS
MIN. TYP. MAX. UNIT
VPSF
IF = 100 µA; VDS = 5 V
2.5
3.45
4
V
Normal operation or
protection latched
Supply current
IPS, IPSL
V(CL)PS
VPS = 4.5 V
IP = 1.5 mA
-
210
6.5
450
8.5
µA
Clamping voltage
5.5
V
Overload protection latched
VPSR
tpr
Reset voltage
Reset time
1
10
1.8
45
3
120
V
µs
VPS ≤ 1 V
OPEN CIRCUIT LOAD DETECTION CHARACTERISTICS
An open circuit load condition can be detected while the TOPFET is in the off-state. Refer to TRUTH TABLE.
VPS = 5 V. Limits are for -40˚C ≤ Tmb ≤ 150˚C and typicals are for Tmb = 25˚C.
SYMBOL PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
IDSP
VDSF
VISF
Off-state drain current2
Drain threshold voltage3
Input threshold voltage4
VIS = 0 V; 2 V ≤ VDS ≤ 40 V
VIS = 0 V
0.9
0.2
0.3
1.8
1
2.7
2
mA
V
ID = 100 µA
0.8
1.1
V
OVERLOAD CHARACTERISTICS
Tmb = 25˚C unless otherwise specified.
SYMBOL PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
Short circuit load protection VPS > 4 V
ID
Drain current limiting
Overload power threshold
Characteristic time
VIS = 5 V;
-40˚C ≤ Tmb ≤ 150˚C
40
90
62
84
A
PD(TO)
TDSC
for protection to operate
which determines trip time5
220
500
330
700
W
µs
250
Overtemperature protection
VPS = 5 V
Tj(TO)
Threshold temperature
from ID ≥ 4 A or VDS > 0.2 V
150
170
-
˚C
1 When VPS is less than VPSF the flag pin indicates low protection supply voltage. Refer to TRUTH TABLE.
2 The drain source current which flows in a normal load when the protection supply is high and the input is low.
3 If VDS < VDSF then the flag indicates open circuit load.
4 For open circuit load detection, VIS must be less than VISF
.
5 Trip time td sc varies with overload dissipation PD according to the formula td sc ~ TDSC / ln[ PD / PD(TO)].
October 2002
4
Rev 1.000
Philips Semiconductors
Product specification
Logic level TOPFET
PIP3121-A
TRUTH TABLE
For normal, open-circuit load and overload conditions or inadequate protection supply voltage.
Assumes proper external pull-up for flag pin. Refer to FLAG CHARACTERISTICS.
CONDITION
PROTECTION
INPUT
FLAG
OUTPUT
Normal on-state
Normal off-state
Open circuit load
Open circuit load
Short circuit load1
Over temperature
1
1
0
ON
1
1
1
1
1
0
0
0
1
0
1
X
1
0
0
0
1
1
1
1
1
OFF
ON
OFF
OFF
OFF
ON
Low protection supply voltage
Low protection supply voltage
OFF
KEY ‘0’ equals low
‘1’ equals high
‘X’ equals don’t care.
FLAG CHARACTERISTICS
The flag is an open drain transistor which requires an external pull-up circuit.
Limits are for -40˚C ≤ Tmb ≤ 150˚C; typicals are for Tmb = 25˚C.
SYMBOL PARAMETER
Flag ‘low’
CONDITIONS
normal operation; VPS = 5 V
IF = 100 µA
MIN. TYP. MAX. UNIT
VFSF
IFSF
Flag voltage
-
-
0.8
10
1
-
V
Flag saturation current
Flag ‘high’
VFS = 5 V
mA
overload or fault
VFS = 5 V
IFSO
Flag leakage current
Flag clamping voltage
Application information
-
0.1
6.2
10
µA
V(CL)FS
IF = 100 µA
5.5
8.5
V
RF
Suitable external pull-up
resistance
VFF = 5 V
-
47
-
kΩ
SWITCHING CHARACTERISTICS
Tmb = 25˚C; RI = 50 Ω; RIS = 50 Ω; VDD = 15 V; resistive load RL = 10 Ω.
SYMBOL PARAMETER CONDITIONS
MIN. TYP. MAX. UNIT
td on
tr
td off
tf
Turn-on delay time
Rise time
VIS: 0 V
VIS: 5 V
5 V
0 V
-
-
-
-
1.8
3.5
11
5
5
8
µs
µs
µs
µs
Turn-off delay time
Fall time
30
12
1 In this condition the protection circuit is latched. To reset the latch the protection pin must be taken low. Refer to PROTECTION SUPPLY
CHARACTERISTICS.
October 2002
5
Rev 1.000
Philips Semiconductors
Product specification
Logic level TOPFET
PIP3121-A
MECHANICAL DATA
Plastic single-ended package; heatsink mounted; 1 mounting hole;
SOT263B-01
5-lead TO-220 lead form option
E
p
A
1
A
p
1
q
D
1
mounting
base
D
L
3
R
L
1
L
L
4
m
L
2
R
Q
1
5
e
b
w
M
c
Q
1
Q
2
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
(2)
L
4
(1)
b
D
A
A
c
D
E
UNIT
mm
e
L
L
L
m
p
p
q
Q
Q
Q
2
R
w
L
1
1
1
2
3
1
1
max.
4.5 1.39 0.85 0.7 15.8 6.4 10.3
4.1 1.27 0.70 0.4 15.2 5.9 9.7
9.8 5.9 5.2 2.4
9.7 5.3 5.0 1.6
0.8 3.8 4.3 3.0
0.6 3.6 4.1 2.7
1.7
0.5
2.0 4.5 8.2 0.5 0.4
Notes
1. Terminal dimensions are uncontrolled in this zone.
2. Positional accuracy of the terminals is controlled in this zone.
REFERENCES
EUROPEAN
PROJECTION
OUTLINE
VERSION
ISSUE DATE
IEC
JEDEC
EIAJ
5-lead (option)
TO-220
01-01-11
SOT263B-01
Fig.4. SOT263B package1 leadform 263B-01, pin 3 connected to mounting base.
1 Refer to mounting instructions for TO220 envelopes. Epoxy meets UL94 VO at 1/8". Net mass: 2 g
October 2002
6
Rev 1.000
Philips Semiconductors
Product specification
Logic level TOPFET
PIP3121-A
DEFINITIONS
DATA SHEET STATUS
DATA SHEET
STATUS1
PRODUCT
DEFINITIONS
STATUS2
Objective data
Development
This data sheet contains data from the objective specification for
product development. Philips Semiconductors reserves the right to
change the specification in any manner without notice
Preliminary data
Qualification
Production
This data sheet contains data from the preliminary specification.
Supplementary data will be published at a later date. Philips
Semiconductors reserves the right to change the specification without
notice, in order to improve the design and supply the best possible
product
Product data
This data sheet contains data from the product specification. Philips
Semiconductors reserves the right to make changes at any time in
order to improve the design, manufacturing and supply. Changes will
be communicated according to the Customer Product/Process
Change Notification (CPCN) procedure SNW-SQ-650A
Limiting values
Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and
operation of the device at these or at any other conditions above those given in the Characteristics sections of
this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
Philips Electronics N.V. 2002
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the
copyright owner.
The information presented in this document does not form part of any quotation or contract, it is believed to be
accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under patent or other
industrial or intellectual property rights.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices or systems where malfunction of these
products can be reasonably expected to result in personal injury. Philips customers using or selling these products
for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting
from such improper use or sale.
1 Please consult the most recently issued datasheet before initiating or completing a design.
2 The product status of the device(s) described in this datasheet may have changed since this datasheet was published. The latest information is
available on the Internet at URL http://www.semiconductors.philips.com.
October 2002
7
Rev 1.000
相关型号:
PIP3122-R
IC 62 A BUF OR INV BASED PRPHL DRVR, PSSO5, PLASTIC, SOT-426, D2PAK-5, Peripheral Driver
NXP
PIP3207-DC,118
IC 8 A BUF OR INV BASED PRPHL DRVR, PSSO6, PLASTIC, SOT-427, D2PAK-7, Peripheral Driver
NXP
PIP3207-DC/T3
IC 8 A BUF OR INV BASED PRPHL DRVR, PSSO6, PLASTIC, SOT-427, D2PAK-7, Peripheral Driver
NXP
©2020 ICPDF网 联系我们和版权申明