MIP2F40MTSCF [PANASONIC]
Switching Regulator,;
| 型号： | MIP2F40MTSCF |
| 厂家： | 
PANASONIC |
| 描述： | Switching Regulator, 开关 |
| 文件： | 总7页 (文件大小：269K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Doc No. TD4-EA-01806
Revision. 1
MIP2F40MTSCF
種別／Type
シリコン ＭＯＳ形集積回路／Silicon MOSFET type Integrated Circuit
用途／Application
構造／Structure
スイッチング電源制御用／For Switching Power Supply Control
ＣＭＯＳ形／CMOS type
等価回路／Equivalent Circuit
添付図／See Figure．6
外形／Out Line ＤＩＰ7－Ａ1－Ｂ
ﾏｰｸ記号／ﾏｰｷﾝｸﾞ／Marking
ＭＩＰ２Ｆ４
Ａ．絶対最大定格／ABSOLUTE MAXIMUM RATINGS （Ｔａ＝２５℃±３℃）
記号／
単位／
備考／Note
Unit
NO.
項目／Item
定格／Ratings
Symbol
※１：
ドレイン電圧
1
2
DRAIN Voltage
ＶＤ
－０．３ ～ ７００
－０．３ ～ ４５
－０．３ ～ ８
－０．３ ～ ８
５００
Ｖ
Ｖ
下記パルス幅以内での
保証とする
ＶＣＣ電圧
VCC Voltage
ＶＣＣ
ＶＤＤ
ＶＦＢ
ＩＦＢ
(It is guaranteed within
the pulse as below.)
ＶＤＤ電圧
3
VDD Voltage
Ｖ
フィードバック電圧
FEEDBACK Voltage
4
Ｖ
オン時ブランキング幅
＋過電流保護遅れ時間
Leading Edge Blanking
Pulse + Current Limit
Delay
フィードバック電流
FEEDBACK Current
5
ｕＡ
Ｖ
ＣＬ端子電圧
CL Voltage
6
ＶＣＬ
ＩＣＬ
－０．３ ～ ８
１５０
ton(BLK)＋td(OCL)
ＣＬ端子電流
CL Current
7
ｕＡ
Ａ
出力ピーク電流
8
Output Peak Current
ＩＤP
１．５ （※１）
１５０
チャネル部温度
9
Channel Temperature
Ｔｃｈ
Ｔｓｔｇ
℃
℃
保存温度
10
Storage Temperature
－５５ ～ ＋１５０
Ｂ．電気的特性／ELECTRICAL CHARACTERISTICS
測定条件／Measure condition (TC=25℃±2℃)
Limit
記号／
Symbol
測定条件／Measure Condition
（測定図-1 参照／See Figure 1）
No.
項目／Item
Typ.
Unit
Min
Max
【コントロール機能／CONTROL FUNCTIONS】
出力周波数
1
fosc
100
12
90
9
110
15
kHz
kHz
VCC=15 V, VD=5 V, IFB=20 uA, ICL=50 uA
VCC=15 V, VD=5 V, IFB:OPEN, ICL<ICL1
Output Frequency
fosc（L）
MAXDC
VDD
最大デューティサイクル
2
3
4
Maximum Duty Cycle
47.5
5.9
45
5.4
4.6
50
6.4
5.6
%
VCC=15 V, VD=5 V, IFB=20 uA, ICL=50 uA
VCC=15 V, VD=5 V, IFB=20 uA, ICL=50 uA
VD=5 V, IFB=20 uA, ICL=50 uA
ＶＤＤ基準電圧
VDD Voltage
Ｖ
Ｖ
ＶＤＤ停止電圧
UV Lockout Threshold Voltage
VUV
5.1
Publication date: 2012-10-25
Doc No. TD4-EA-01806
Revision. 1
MIP2F40MTSCF
Limit
記号／
Symbol
測定条件／Measure Condition
（測定図-1 参照／See Figure 1）
No.
項目／Item
Typ.
Unit
Min
Max
【コントロール機能／CONTROL FUNCTIONS】
ＶＣＣ起動電圧
5
6
7
8
9
VCC Start Voltage
VCC(ON)
VCC1
IFB１
7.5
12
6.5
11
50
8.5
13
V
V
VD=5 V, IFB=20 uA, ICL=50 uA
ＶＣＣ充電停止電圧
VCC Charge Stop Threshold Voltage
VD=40 V, FB:OPEN, CL:OPEN
ON → OFF
フィードバック電流
Feedback Threshold Current
80
110
uA
uA
uA
V
VCC=15 V, VD=5 V, ICL=50 uA
フィードバック電流ヒステリシス
Feedback Hysteresis Current
IFBHYS
IFB0
6
VCC=15 V, VD=5 V, ICL=50 uA
ICC0 → ICC
重負荷時ＦＢ端子電流
FB Pin Current at Heavy Load
11
7
15
VCC=15 V, VD=5 V, ICL=50 uA
ＦＢ端子電圧
10 FB Pin Voltage
VFB
1.0
0.45
0.27
0.7
0.25
0.2
1.3
VCC=15 V, VD=5 V, IFB=20 uA, ICL=50 uA
回路消費電流
11 Supply Current
ICC
0.55
0.35
mA
mA
VCC=15 V, VD=5 V, IFB=20 uA, ICL=50 uA
VCC=15 V, VD=5 V
軽負荷時回路消費電流
12 Supply Current at Light Load
ICC(OFF)
IFB=IFB1+5 uA, ICL=50 uA
重負荷時回路消費電流
13 Supply Current at Heavy Load
ICC0
Ich1
Ich2
0.63
7
0.48
5
0.78
9
mA
mA
mA
VCC=15 V, VD=5 V, IFB=OPEN, ICL=50 uA
VDD=0 V, VD=40 V, FB:OPEN, CL:OPEN
VDD=4 V, VD=40 V, FB:OPEN, CL:OPEN
ＶＤＤ充電電流
14 VDD Charging Current
2.3
1
3.6
ＣＬ端子電圧
15 CL Pin Voltage
VCL
2.3
12
2.0
9
2.6
15
Ｖ
VCC=15 V, VD=5 V, FB:OPEN, ICL=15 uA
fosc 低下時ＣＬ端子電流
fosc → fosc（L）
※Figure 3
16 Dropped fosc CL Pin Current
ICL1
uA
uA
VCC=15 V, VD=5 V, FB:OPEN
fosc 低下時ＣＬ端子電流ヒステリシス
17 CL Pin Hysteresis Current
※Figure 3
ICLHYS
1.0
VCC=15 V, VD=5 V, FB:OPEN
【保護機能／CIRCUIT PROTECTIONS：*は設計保証項目/Design Guarantee Item】
過電流保護検出
18 Self Protection Current Limit
※Figure 2/Figure 4
VCC=15 V, FB:OPEN, ICL=50 uA,DUTY=30％
※Figure 2/Figure 4
ILIMIT
0.70
40
0.63
0.77
Ａ
mA/us
mA
mA
ns
ILIMIT 補正係数
19 ILIMIT modified coefficient
R_slope
VCC=15 V, FB:OPEN, ICL=50 uA
Ton=3 usec
最小ＩＬＩＭＩＴ
20 Minimum ILIMIT
170
140
240
150
24
90
50
250
230
310
200
27
ILIMITmin
ID(OFF)
ton(BLK)
td(OCL)
VCC=15 V, FB:OPEN, ICL=0 uA
Ton=3 usec
*
*
*
軽負荷時ドレイン電流
21 Drain Current at Light Load
VCC=15 V, IFB=IFB1+IFBHYS, ICL=50 uA
オン時ブランキング幅
22 Leading Edge Blanking Delay
170
100
21
VCC=15 V, FB:OPEN, ICL=50 uA
VDD=5 V, FB:OPEN, ICL=50 uA
過電流保護遅れ時間
23 Current Limit Delay
ns
過電圧保護検出
24 Over Voltage Protection
Ｖ
VCC(OV)
TOTP
*
過熱保護温度
25 Thermal Shutdown Temperature
140
130
150
℃
Publication date: 2012-10-25
Doc No. TD4-EA-01806
Revision. 1
MIP2F40MTSCF
Limit
記号／
Symbol
測定条件／Measure Condition
（測定図-1 参照／See Figure 1）
No.
項目／Item
Typ.
Unit
Min
1.8
Max
【出力／OUTPUT】
ラッチリセット電圧
26 Power-up Reset Threshold Voltage
VDDreset
RDS(ON)
2.6
7
3.5
9.5
20
Ｖ
Ω
uA
Ｖ
オン抵抗
27 ON-State Resistance
ID=100 mA
オフ時ドレイン端子リーク電流
28 OFF-State Current
10
IDSS
VCC=27 V, VD=650 V, FB:OPEN, CL:OPEN
ドレイン耐圧
29 Breakdown Voltage
VDSS
700
VCC=27 V, ID=100 uA, FB:OPEN, CL:OPEN
※Figure 5
立ち上がり時間
30 Rise Time
100
50
ns
ns
tr
tf
VCC=15 V, VD=5 V, FB:OPEN, ICL=50 uA
※Figure 5
立ち下がり時間
31 Fall Time
VCC=15 V, VD=5 V, FB:OPEN, ICL=50 uA
【電源電圧／SUPPLY】
最小ドレイン電圧
32 Drain Supply Voltage
50
Ｖ
VD(MIN)
VCC：OPEN, FB:OPEN, CL:OPEN
【Ｆｉｇ．１：測定回路図／Measure Circuit】
270 uH
D
VCC
56k
CL
S
S
FB
22k
VDD
0.1uF
0.1uF
Publication date: 2012-10-25
Doc No. TD4-EA-01806
Revision. 1
MIP2F40MTSCF
【Ｆｉｇ．２：ＩＬＩＭＩＴ ｖｓ． ＩＣＬ Typical Characteristic】
ILIMITꢀ-ꢀICL
800
600
400
200
0
0
10
20
30
40
50
ICL [uA]
【Ｆｉｇ．３：ｆｏｓｃ ｖｓ． ＩＣＬ Typical Characteristic】
fosc vs. ICL
120
100
80
60
40
20
0
0
10
20
ICL[uA]
30
40
【Ｆｉｇ．４： ILIMIT Measurement】
ILIMIT
ＩD
ｔ
R_slope ; {(ILIMIT at Duty=30%) – (ILIMIT at Duty=10%)} / {(Ton at Duty=30%) – (Ton at Duty=10%)}
Publication date: 2012-10-25
Doc No. TD4-EA-01806
Revision. 1
MIP2F40MTSCF
【Ｆｉｇ．５ ： tr、tf Measurement】
ｔｆ
ｔｒ
VD
90%
10%
0
【Ｆｉｇ．６： Block Diagram】
VCC
VDD
DRAIN
VCC UV
regulator
7.5V
VCC OVP
5.7V
6.6V
CL
Constant
current resource
24V
VDD clamp circuit
Overheat
protection
S
Q
Q
5.9V
5.1V
VDD UV
R
Restart
trigger
Oscillator
MAXDC
Gate driver
ＩＬＩＭＩＴ
variable
circuit（15～100%）
12kHz
CLOCK
S
R
Q
Q
power
MOSFET
IN
ICL_LOW
Blanking pulse
gen eration
circuit in on-state
VCL_OUT
27%
22%
ILIMIT
compensation
FB
Light load detection
For intermittent
Oscillation control
Drain current
for detection
VCL
clamp circuit
（ILIMIT setting）
SOURCE
Publication date: 2012-10-25
Doc No. TD4-EA-01806
Revision. 1
MIP2F40MTSCF
【Ｆｉｇ．7：端子配置図／Pin Layout 】
８
７
Pin No.
端子名／Terminal Name
１
２
３
４
１
２
３
４
５
６
７
８
VDD
FB
CL
VCC
Drain
－
Source
Source
５
【使用上の注意１／Precautions for Use 1】
VDD 端子－ＧＮＤ間には、０．１ｕＦのセラミックコンデンサを使用してください。
Connect a 0.1uF ceramic capacitor between VDD pin and GND.
【使用上の注意２／Precautions for Use ２】
以下のような条件では破損し、場合によっては破裂、発煙の可能性があります。以下の使用は避けてください。
The IPD has risks for break-down or burst or giving off smoke in following conditions. Avoid the following use.
（1） DRAIN 端子と VDD 端子を逆にして、電源基板へ挿入する。
Reverse the DRAIN pin and VDD pin connection to the power supply board.
（2） DRAIN 端子と VDD 端子をショートする。
DRAIN pin short to VDD pin.
（3） ＤＲＩＮ端子と FB 端子をショートする。
DRAIN pin short to FB pin.
（4） ＤＲＩＮ端子とＣＬ端子をショートする。
DRAIN pin short to ＣＬ pin.
（5） ＤＲＩＮ端子と VCC 端子をショートする。
DRAIN pin short to VCC pin.
（6） VCC 端子と VDD 端子をショートする。
VCC pin short to VDD pin.
（7） VCC 端子と FB 端子をショートする。
VCC pin short to FB pin.
（8） VCC 端子と CL 端子をショートする。
VCC pin short to CL pin.
Publication date: 2012-10-25
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any
other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any
other company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for general applications (such as office equipment, communications
equipment, measuring instruments and household appliances), or for specific applications as expressly stated in this book.
Consult our sales staff in advance for information on the following applications:
Special applications (such as for airplanes, aerospace, automotive equipment, traffic signaling equipment, combustion equipment,
life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of
the products may directly jeopardize life or harm the human body.
It is to be understood that our company shall not be held responsible for any damage incurred as a result of or in connection with
your using the products described in this book for any special application, unless our company agrees to your using the products in
this book for any special application.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or improve-
ment. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards
in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company.
Precautions on the Sales of IPDs
1) The sale and/or the export of IPD products to customers located in certain countries is restricted by the Agreement made and
executed by and between Power Integrations, Inc. and Panasonic Corporation. For details, refer to the following Attached table
"IPD availability by customer."
2) IPD products purchased from our company, or its authorized agents, hereinafter referred to as our company, shall be used only
for production purposes by those parties who have duly purchased IPD products. Those who have purchased IPD products shall
not use such IPD products in unmodified form for re-sale, loan, or sample shipment for evaluation purposes to any other
parties.
3) If a party who has duly purchased IPD products subcontracts its production to any other parties, including its subsidiaries or any other
third parties inside and/or out of Japan, and the IPD products are consigned to such subcontracting parties thereat, such party is
obligated to monitor and control the quantity of IPD products to prevent any of the aforementioned re-sale, loan or sample shipments
from taking place.
4) In the event that any actual or threatened breach or violation of any of the above mentioned 2) or 3) has occurred or is about to occur,
our company will hold all shipments of IPD products and may request the customer to disclose necessary documentation describing
the status of our end-users and/or distribution channels.
Note) The products of MIP50**, MIP51**, and MIP7** are excluded from above-mentioned precautions, 1) to 3).
Attached table "IPD availability by customer"
Companies/areas to which Companies/areas to which
Application
Parts No.
products can be sold
products cannot be sold
·
·
Japanese companies in Japan
Japanese companies in Asia
(50% or more owned)
·
Companies in European
and American countries
Asian companies in Asia
Other local companies
·
·
For power supply
For DC-DC converter
MIP01**
MIP2**
MIP9A**
MIP02**
MIP3**
MIP9L**
MIP1**
MIP4**
·
·
·
·
Japanese companies in Japan
Japanese companies in Asia
(50% or more owned)
·
·
·
For power supply
For EL driver
For LED lighting driver
·
·
Companies in European
and American countries
Other local companies
MIP00**
MIP55**
MIP52**
MIP56**
MIP53**
MIP5S**
MIP803/804 MIP816/826 MIP9E**
·
·
Asian companies in Asia
No restrictions in terms of
contract
·
For lamp driver/
car electronics accessories
·
No restrictions in terms of
contract
MIP50**
MIP51**
MIP7**
Note) For details, contact our sales division.
20140519
相关型号：
©2020 ICPDF网 联系我们和版权申明