MIP2K20MS [PANASONIC]
Battery Charge Controller, PDIP7;
| 型号： | MIP2K20MS |
| 厂家： | 
PANASONIC |
| 描述： | Battery Charge Controller, PDIP7 电池 光电二极管 |
| 文件： | 总6页 (文件大小：686K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MIP2K20MS
Silicon MOS FET type integrated circuit
Features
Package
Built-in jitter function
ꢀCode
DIP7-A1
ꢀPin Name
1. VDD
2. FB
Built-in charge protection circuit
Built-in overheating, loadshorting and overvoltage protection circuits
5. DRAIN
6.
7. SOURCE
8. SOURCE
Applications
Chargers (for DSC, etc.)
AC adapter
3. CL
4. VCC
Marking Symbol: MIP2K2
Absolute Maximum Ratings Ta = 25°C±3°C
Parameter
DRAIN voltage
Symbol
VD
Rating
- 0.3 to +700
- 0.3 to +45
- 0.3 to +8
- 0.3 to +8
500
Unit
V
VCC voltage
VCC
VDD
VFB
IFB
V
VDD voltage
V
Feedback voltage
Feedback current
CL pin voltage
V
mA
V
VCL
ICL
- 0.3 to +8
150
CL pin current
mA
A
Output peak current *
Channel temperature
Storage temperature
IDP
0.95
Tch
150
°C
°C
Tstg
-55 to +150
Note) : The guarantee within the following pulse width.
*
Leading edge blanking delay + Current limit delay ton(BLK) + td(OCL)
Block Diagram
VCC
DRAIN
VCC UV
Regulator
VDD
CL
VCC(ON)
VCC(OV)
Constant
VDD
VCC OVP
current resource
Overheat
S
Q
Q
protection
VDD UV
Restart
trigger
R
Oscillator with Jitter
MAXDC
Gate driver
Power
ILIMIT
variable circuit
MOSFET
fosc(L)
CLOCK
S
Q
Q
IN
R
ICL_LOW
VCL_OUT
Blanking pulse
generation
ILIMIT
compensation
circuit in on-state
Light load detection
For intermittent
FB
Oscillation control
Drain current
for detection
VCL
Clamp circuit
(ILIMIT setting)
SOURCE
Publication date: October 2010
Ver. AEF
1
MIP2K20MS
Electrical Characteristics TC = 25°C±2°C
Parameter
Control functions
Symbol
Conditions
Min
Typ
Max
Unit
VCC = 15 V, VD = 5 V, IFB = 20 mA,
ICL = 50 mA
fosc
fosc(L)
∆f
90
9
100
12
110
15
kHz
kHz
kHz
Hz
Output frequency
VCC = 15 V, VD = 5 V, IFB: Open,
ICL < ICL1
VCC = 15 V, VD = 5 V, IFB = 20 mA,
ICL = 50 mA
Jitter frequency deviation
Jitter frequency modulation rate
Maximum duty cycle
VDD voltage
5.5
VCC = 15 V, VD = 5 V, IFB = 20 mA,
ICL = 50 mA
fM
260
47.5
5.9
VCC = 15 V, VD = 5 V, IFB = 20 mA,
ICL = 50 mA
MAXDC
45
50
%
VCC = 15 V, VD = 5 V, IFB = 20 mA,
ICL = 50 mA
VDD
VUV
5.4
6.4
V
UV lockout threshold voltage
VCC start voltage
VD = 5 V, IFB = 20 mA, ICL = 50 mA
4.6
5.9
5.1
6.9
5.6
7.9
V
V
V
VCC(ON) VD = 5 V, IFB = 20 mA, ICL = 50 mA
VCC charge stop threshold voltage
VCC1
VD = 40 V, FB: Open, CL: Open
11.8
12.8
13.8
ON → OFF
VCC = 15 V, VD = 5 V, ICL = 50 mA
Feedback threshold voltage
Feedback hysteresis current
FB pin current at heavy load
IFB1
21
41
2
61
mA
mA
mA
IFBHYS VCC = 15 V, VD = 5 V, ICL = 50 mA
ICC0 → ICC
IFB0
6
9.5
13
1.3
VCC = 15 V, VD = 5 V, ICL = 50 mA
VCC = 15 V, VD = 5 V, IFB = 20 mA,
ICL = 50 mA
FB pin voltage
VFB
0.7
1.0
0.40
0.36
0.60
-3.8
-1.3
2.3
V
VCC = 15 V, VD = 5 V, IFB = 20 mA,
ICL = 50 mA
Supply current
ICC
0.25
0.26
0.45
-5.8
-2.2
2.0
0.50
0.46
0.75
-1.8
- 0.4
2.6
mA
mA
mA
mA
mA
V
VCC = 15 V, VD = 5 V,
ICC(OFF)
Supply current at light load
Supply current at heavy load
IFB = IFB1 + 5 mA, ICL = 50 mA
VCC = 15 V, VD = 5 V, IFB: Open,
ICC0
ICL = 50 mA
VDD = 0 V, VD = 40 V, FB: Open,
Ich1
CL: Open
VDD charging current
VDD = 4 V, VD = 40 V, FB: Open,
Ich2
CL: Open
VCC = 15 V, VD = 5 V, FB: Open,
CL pin voltage
VCL
ICL = ICL1
fosc → fosc(L)
ICL1
2
Dropped fosc CL pin current *
16.5
22
27.5
mA
mA
VCC = 15 V, VD = 5 V, FB: Open
2
CL pin hysteresis current *
ICLHYS VCC = 15 V, VD = 5 V, FB: Open
1.5
2
Ver. AEF
MIP2K20MS
Electrical Characteristics (continued) TC = 25°C±2°C
Parameter
Circuit protections
Symbol
Conditions
Min
Typ
Max
Unit
VCC = 15 V, FB: Open, ICL = 50 mA,
DUTY = 30%
1, 3
Self protection current limit *
ILIMIT
R_slope
0.315
0.350
28
0.385
A
1, 3
ILIMIT modified coefficient *
VCC = 15 V, FB: Open, ICL = 50 mA
mA/ms
mA
Ton = 3 ms, VCC = 15 V, FB: Open,
ICL = 0 mA
Minimum ILIMIT
ILIMITmin
40
30
110
200
150
Ton = 3 ms, VCC = 15 V,
IFB = IFB1 + IFBHYS, ICL = 50 mA
Drain current at light load
ID(OFF)
70
mA
Leading edge blanking delay
Current limit delay
ton(BLK) VCC = 15 V, FB: Open, ICL = 50 mA
230
100
22
290
150
24.5
140
350
200
27
ns
ns
V
td(OCL)
Over voltage protection
VCC(OV) VD = 5 V, FB: Open, ICL = 50 mA
Thermal shutdown temperature
Output
TOTP
130
150
°C
Power up reset threshold voltage
ON state resistance
VDDreset
1.8
2.6
3.5
21
V
RDS(ON) ID = 100 mA
16.5
W
VCC = 26 V, VD = 650 V, FB: Open,
OFF state current
IDSS
10
20
mA
V
CL: Open
VCC = 26 V, ID = 100 mA, FB: Open,
CL: Open
Breakdown voltage
VDSS
700
VCC = 15 V, VD = 5 V, FB: Open,
4
Rise time *
tr
100
25
ns
ns
ICL = 50 mA
VCC = 15 V, VD = 5 V, FB: Open,
4
Fall time *
tf
ICL = 50 mA
Supply voltage characteristics
Drain supply voltage
VD(MIN) VCC: Open, FB: Open, CL: Open
50
V
Note) 1. Measurement circuit
Ver. AEF
3
MIP2K20MS
Electrical Characteristics (continued) TC = 25°C±2°C
2. 1: ILIMIT vs. ICLTypical characteristic
*
2: fosc vs. ICLTypical characteristic
*
*3: ILIMIT Measurement
4: tr, tf Measurement
*
4
Ver. AEF
MIP2K20MS
Frequency jitter function
By frequency jitter function, frequency jitter variation(∆f) changes periodically, by frequency of frequency jitter modulation factor (fM) as
shown below.
ꢀꢀfosc = 100 kHz (typ.), ∆f = 5.5 kHz (typ.), fM = 260 Hz (typ.)
Adapter circuit sample (MIP2K4)
Electric characteristics (MIP2K4：Worldwide input, 8.3V/1.5A output)
Ver. AEF
5
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any
other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any
other company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for general applications (such as office equipment, communications
equipment, measuring instruments and household appliances), or for specific applications as expressly stated in this book.
Consult our sales staff in advance for information on the following applications:
Special applications (such as for airplanes, aerospace, automotive equipment, traffic signaling equipment, combustion equipment,
life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of
the products may directly jeopardize life or harm the human body.
It is to be understood that our company shall not be held responsible for any damage incurred as a result of or in connection with
your using the products described in this book for any special application, unless our company agrees to your using the products in
this book for any special application.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or improve-
ment. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards
in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company.
Precautions on the Sales of IPDs
1) The sale and/or the export of IPD products to customers located in certain countries is restricted by the Agreement made and
executed by and between Power Integrations, Inc. and Panasonic Corporation. For details, refer to the following Attached table
"IPD availability by customer."
2) IPD products purchased from our company, or its authorized agents, hereinafter referred to as our company, shall be used only
for production purposes by those parties who have duly purchased IPD products. Those who have purchased IPD products shall
not use such IPD products in unmodified form for re-sale, loan, or sample shipment for evaluation purposes to any other
parties.
3) If a party who has duly purchased IPD products subcontracts its production to any other parties, including its subsidiaries or any other
third parties inside and/or out of Japan, and the IPD products are consigned to such subcontracting parties thereat, such party is
obligated to monitor and control the quantity of IPD products to prevent any of the aforementioned re-sale, loan or sample shipments
from taking place.
4) In the event that any actual or threatened breach or violation of any of the above mentioned 2) or 3) has occurred or is about to occur,
our company will hold all shipments of IPD products and may request the customer to disclose necessary documentation describing
the status of our end-users and/or distribution channels.
Note) The products of MIP50**, MIP51**, and MIP7** are excluded from above-mentioned precautions, 1) to 3).
Attached table "IPD availability by customer"
Companies/areas to which Companies/areas to which
Application
Parts No.
products can be sold
products cannot be sold
·
·
Japanese companies in Japan
Japanese companies in Asia
(50% or more owned)
·
Companies in European
and American countries
Asian companies in Asia
Other local companies
·
·
For power supply
For DC-DC converter
MIP01**
MIP2**
MIP9A**
MIP02**
MIP3**
MIP9L**
MIP1**
MIP4**
·
·
·
·
Japanese companies in Japan
Japanese companies in Asia
(50% or more owned)
·
·
·
For power supply
For EL driver
For LED lighting driver
·
·
Companies in European
and American countries
Other local companies
MIP00**
MIP55**
MIP816/826 MIP9E**
MIP52**
MIP56**
MIP53**
MIP803/804
·
·
Asian companies in Asia
No restrictions in terms of
contract
·
For lamp driver/
car electronics accessories
·
No restrictions in terms of
contract
MIP50**
MIP51**
MIP7**
Note) For details, contact our sales division.
20130322
相关型号：
©2020 ICPDF网 联系我们和版权申明