NCP603SN300T1G [ONSEMI]
300 mA High Performance CMOS LDO Regulator with Enable and Enhanced ESD Protection; 300毫安高性能CMOS LDO稳压器具有使能和增强型ESD保护型号: | NCP603SN300T1G |
厂家: | ONSEMI |
描述: | 300 mA High Performance CMOS LDO Regulator with Enable and Enhanced ESD Protection |
文件: | 总13页 (文件大小:135K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NCP603
Product Preview
300 mA High Performance
CMOS LDO Regulator with
Enable and Enhanced ESD
Protection
http://onsemi.com
The NCP603 provides 300 mA of output current at fixed voltage
options, or an adjustable output voltage from 5.0 V down to 1.250 V. It
is designed for portable battery powered applications and offers high
performance features such as low power operation, fast enable
response time, and low dropout.
5
1
TSOP-5
SN SUFFIX
CASE 483
The device is designed to be used with low cost ceramic capacitors
and is packaged in the TSOP-5/SOT23-5.
MARKING DIAGRAM
Features
•ꢀOutput Voltage Options:
5
Adjustable, 1.3 V, 1.5 V, 1.8 V, 2.8 V, 3.0 V, 3.3 V, 3.5 V, 5.0 V
xxx AYWG
•ꢀAdjustable Output by External Resistors from 5.0 V down to 1.250 V
G
•ꢀFast Enable Turn-on Time of 15 ms
•ꢀWide Supply Voltage Range Operating Range
•ꢀExcellent Line and Load Regulation
1
xxx
A
= Specific Device Code
= Assembly Location
= Year
•ꢀTypical Noise Voltage of 50 mV without a Bypass Capacitor
Y
W
rms
= Work Week
•ꢀEnhanced ESD Protection (HBM 3.5 kV, MM 400 V)
•ꢀThese are Pb-Free Devices
G = Pb-Free Package
(Note: Microdot may be in either location)
Typical Applications
•ꢀSMPS Post-Regulation
PIN CONNECTIONS
•ꢀHand-held Instrumentation & Audio Players
•ꢀNoise Sensitive Circuits – VCO, RF Stages, etc.
•ꢀCamcorders and Cameras
V
1
2
5
4
V
out
in
GND
•ꢀPortable Computing
ENABLE
3
ADJ/NC*
V
OUT
V
IN
(Top View)
Fixed Voltage Only
* ADJ - Adjustable Version
* NC - Fixed Voltage Version
Driver w/
Current Limit
+
-
+
1.25 V
-
GND
ORDERING INFORMATION
Thermal
Shutdown
See detailed ordering and shipping information in the
ADJ
package dimensions section on page 12 of this data sheet.
Adjustable Version Only
ENABLE
Figure 1. Simplified Block Diagram
This document contains information on a product under development. ON Semiconductor
reserves the right to change or discontinue this product without notice.
©ꢀ Semiconductor Components Industries, LLC, 2007
November, 2007 - Rev. P1
1
Publication Order Number:
NCP603/D
NCP603
PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
Description
1
2
3
V
Positive Power Supply Input
Power Supply Ground; Device Substrate
in
GND
ENABLE
The Enable Input places the device into low-power standby when pulled to logic low (< 0.4 V). Connect to V
if the function is not used.
in
4
5
ADJ/NC
Output Voltage Adjust Input (Adjustable Version), No Connection (Fixed Voltage Versions) (Note 1)
Regulated Output Voltage
V
out
1. True no connect. Printed circuit board traces are allowable.
ABSOLUTE MAXIMUM RATINGS
Rating
Input Voltage (Note 2)
Symbol
Value
Unit
V
V
in
-0.3 to 6.5
Output, Enable, Adjustable Voltage
V
out
, ENABLE, ADJ
-0.3 to 6.5 (or V + 0.3)
in
Whichever is Lower
V
Maximum Junction Temperature
Storage Temperature
T
150
°C
°C
V
J(max)
T
-65 to 150
3500
STG
ESD Capability, Human Body Model (Note 3)
ESD Capability, Machine Model (Note 3)
Moisture Sensitivity Level
ESD
HBM
ESD
400
V
MM
MSL
MSL1/260
-
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
2. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
3. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC-Q100-002 (EIA/JESD22-A114)
ESD Machine Model tested per AEC-Q100-003 (EIA/JESD22-A115)
Latchup Current Maximum Rating: v150 mA per JEDEC standard: JESD78.
THERMAL CHARACTERISTICS
Rating
Symbol
Value
Unit
Thermal Characteristics, TSOP-5 (Note 4)
Thermal Resistance, Junction-to-Air (Note 5)
R
°C/W
q
JA
215
4. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
5. Value based on copper area of 645 mm2 (or 1 in2) of 1 oz copper thickness.
OPERATING RANGES (Note 6)
Rating
Symbol
Min
1.75
1.25
0
Max
6
Unit
V
Input Voltage (Note 7)
V
in
Adjustable Output Voltage (Adjustable Version Only)
Output Current
V
5.0
300
125
V
out
out
I
mA
°C
Ambient Temperature
T
A
-40
6. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
7. Minimum Vin = 1.75 V or (V + VDO), whichever is higher.
out
http://onsemi.com
2
NCP603
ELECTRICAL CHARACTERISTICS (V = 1.750 V, V = 1.250 V, C = C =1.0 mF, for typical values T = 25°C, for min/max
in
out
in
out
A
values T = -40°C to 125°C, unless otherwise specified.) (Note 8)
A
Characteristic
Symbol
Test Conditions
Min
Typ
Max
Unit
Regulator Output (Adjustable Voltage Version)
Output Voltage
Output Voltage
V
I
V
V
= 1.0 mA to 150 mA
= 1.75 V to 6.0 V,
= ADJ
1.231
(-1.5%)
1.250
1.269
(+1.5%)
V
out
out
in
out
1.213
(-3%)
1.250
1.287
(+3%)
V
V
I
= 1.0 mA to 300 mA
out
out
V
V
= 1.75 V to 6.0 V,
= ADJ = 1.25 V
in
out
Power Supply Ripple Rejection (Note 9)
PSRR
dB
I
= 1.0 mA to 150 mA
out
V
= V + 1 V + 0.5 V
p-p
out
in
-
-
-
62
55
38
-
-
-
f = 120 Hz
f = 1.0 kHz
f = 10 kHz
Line Regulation
-
1.0
10
mV
mV
Reg
line
V
I
= 1.750 V to 6.0 V,
= 1.0 mA
in
out
Load Regulation
-
-
2.0
50
45
-
Reg
load
I
= 1.0 mA to 300 mA
out
Output Noise Voltage (Note 9)
Output Short Circuit Current
f = 10 Hz to 100 kHz
mV
rms
V
n
500
650
900
mA
mV
I
sc
Dropout Voltage
1.25 V
V
DO
Measured at: V
– 2.0%,
= 150 mA, Figure 2
out
-
175
250
I
out
Dropout Voltage
1.25 V
V
mV
mA
Measured at: V
– 2.0%,
= 300 mA, Figure 2
DO
out
-
375
650
480
-
I
out
Output Current Limit
300
I
out(max)
Regulator Output (Fixed Voltage Version) (V = V + 0.5 V, C = C =1.0 mF, for typical values T = 25°C, for min/max values T =
in
out
in
out
A
A
-40°C to 125°C; unless otherwise noted.) (Note 8)
Output Voltage
1.3 V
1.5 V
(-2%)
1.270
1.470
1.764
2.744
2.940
3.234
3.43
(+2%)
1.326
1.530
1.836
2.856
3.060
3.366
3.57
V
V
I
= 1.0 mA to 150 mA
out
out
V
1.3
1.5
1.8
2.8
3.0
3.3
3.5
5.0
= (V + 0.5 V) to 6.0 V
in
out
1.8 V
2.8 V
3.0 V
3.3 V
3.5 V
5.0 V
4.900
5.100
Output Voltage
1.3 V
1.5 V
(-3%)
1.261
1.455
1.746
2.716
2.910
3.201
3.395
4.850
(+3%)
1.339
1.545
1.854
2.884
3.090
3.399
3.605
5.150
V
V
I
out
= 1.0 mA to 300 mA
out
1.3
1.5
1.8
2.8
3.0
3.3
3.5
5.0
V
in
= (V + 0.5 V) to 6.0 V
out
1.8 V
2.8 V
3.0 V
3.3 V
3.5 V
5.0 V
Power Supply Ripple Rejection (Note 9)
PSRR
dB
I
= 1.0 mA to 150 mA
out
V
= V + 1 V + 0.5 V
p-p
out
in
-
-
-
62
55
38
-
-
-
f = 120 Hz
f = 1.0 kHz
f = 10 kHz
Line Regulation
Load Regulation
-
1.0
10
mV
mV
Reg
line
V
I
= 1.750 V to 6.0 V,
= 1.0 mA
in
out
-
-
2.0
2.0
30
45
Reg
load
I
I
= 1.0 mA to 150 mA
= 1.0 mA to 300 mA
out
out
8. Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at T = T =
A
J
25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
9. Values based on design and/or characterization.
http://onsemi.com
3
NCP603
ELECTRICAL CHARACTERISTICS (V = 1.750 V, V = 1.250 V (adjustable version)), (V = V + 0.5 V (fixed version)),
in
out
in
out
C
= C =1.0 mF, for typical values T = 25°C, for min/max values T = -40°C to 125°C, unless otherwise specified.) (Note 10)
out A A
in
Characteristic
Symbol
Test Conditions
f = 10 Hz to 100 kHz
Min
Typ
Max
Unit
Output Noise Voltage (Note 11)
Output Short Circuit Current
-
50
-
mV
rms
V
n
500
650
900
mA
mV
I
sc
Dropout Voltage
1.3 V
1.5 V
V
Measured at: V – 2.0%
out
DO
DO
-
-
-
-
175
150
125
75
250
225
175
125
I
= 150 mA
out
1.8 V
2.7 V to 5.0 V
Dropout Voltage
1.3 V
1.5 V
V
mV
mA
Measured at: V
out
– 2.0%
-
-
-
-
375
350
245
157
480
400
340
230
I
= 300 mA
out
1.8 V
2.7 V to 5.0 V
Output Current Limit
300
650
-
I
out(max)
General
Disable Current
I
ENABLE = 0 V, Vin = 6 V
-
-
0.01
145
1.0
mA
mA
DIS
-40°C ≤ T ≤ 85°C
A
Ground Current
I
ENABLE = 0.9 V,
180
GND
I
= 1.0 mA to 300 mA
out
Thermal Shutdown Temperature (Note 11)
Thermal Shutdown Hysteresis (Note 11)
ADJ Input Bias Current
T
-
-
175
10
-
-
-
°C
°C
mA
SD
T
SH
I
-0.75
0.75
ADJ
Chip Enable
ENABLE Input Threshold Voltage
V
th(EN)
V
Voltage Increasing, Logic High
Voltage Decreasing, Logic Low
Enable Input Bias Current (Note 11)
Timing
0.9
-
-
-
-
0.4
100
I
t
-
3.0
nA
EN
Output Turn On Time (Note 11)
1.25 V to 3.5 V
5.0 V
ms
ENABLE = 0 V to V
in
EN
-
-
15
30
25
50
10.Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at T = T =
A
J
25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
11. Values based on design and/or characterization.
http://onsemi.com
4
NCP603
5
4
1
2
V
V
OUT
IN
C
C
IN
OUT
3
ENABLE
Figure 2. Typical Application Circuit for Vout = 1.250 V
(Adjustable Version)
5
1
2
V
IN
V
OUT
C
C
IN
OUT
R1
3
4
ENABLE
R2
Figure 3. Typical Application Circuit for Adjustable Vout
5
4
1
2
V
IN
V
OUT
C
C
IN
OUT
3
Figure 4. Typical Application Circuit
(Fixed Voltage Version)
http://onsemi.com
5
NCP603
TYPICAL CHARACTERISTICS
1.260
1.256
1.252
1.248
1.260
1.256
I
= 1.0 mA
I
= 1.0 mA
out
out
1.252
1.248
I
= 150 mA
out
I
= 150 mA
out
V
= V + 0.5 V
out
= ADJ
in
V
= 6.0 V
= ADJ
1.244
1.240
1.244
1.240
in
V
out
V
out
-40 -20
0
20
40
60
80
100 120
-40
-15
10
35
60
85
110 125
T , TEMPERATURE (°C)
A
T , TEMPERATURE (°C)
A
Figure 5. Output Voltage vs. Temperature
(Vin = Vout + 0.5 V)
Figure 6. Output Voltage vs. Temperature
(Vin = 6.0 V)
1.500
1.495
1.490
1.485
1.500
1.495
1.490
1.485
I
= 1.0 mA
out
I
= 1.0 mA
out
I
= 150 mA
out
I
= 150 mA
out
1.480
1.475
1.480
1.475
-40
-15
10
35
60
85
110 125
-40
-15
10
35
60
85
110 125
T , TEMPERATURE (°C)
A
T , TEMPERATURE (°C)
A
Figure 7. Output Voltage vs. Temperature
(1.5 V Fixed Output, Vin = 2 V)
Figure 8. Output Voltage vs. Temperature
(1.5 V Fixed Output, Vin = 6 V)
3.005
3.000
2.995
2.990
3.005
3.000
I
= 1.0 mA
out
I
= 1.0 mA
= 150 mA
out
2.995
2.990
2.985
2.980
I
out
I
= 150 mA
out
2.985
2.980
2.975
2.975
2.970
-40
-15
10
35
60
85
110 125
-40
-15
10
35
60
85
110 125
T , TEMPERATURE (°C)
A
T , TEMPERATURE (°C)
A
Figure 9. Output Voltage vs. Temperature
(3.0 V Fixed Output, Vin = 3.5 V)
Figure 10. Output Voltage vs. Temperature
(3.0 V Fixed Output, Vin = 6 V)
http://onsemi.com
6
NCP603
TYPICAL CHARACTERISTICS
5.000
4.995
4.990
4.985
4.980
4.975
5.000
I
= 1.0 mA
out
I
= 1.0 mA
out
4.995
4.990
4.985
4.980
4.975
I
= 150 mA
out
I
= 150 mA
out
4.970
4.965
4.970
4.965
-40
-15
10
35
60
85
110 125
-40
-15
10
35
60
85
110 125
T , TEMPERATURE (°C)
A
T , TEMPERATURE (°C)
A
Figure 11. Output Voltage vs. Temperature
(5.0 V Fixed Output, Vin = 5.5 V)
Figure 12. Output Voltage vs. Temperature
(5.0 V Fixed Output, Vin = 6 V)
250
200
150
100
250
200
150
100
V
out
= ADJ
I
= 150 mA
out
I
= 150 mA
out
V
out
= 1.25 V
1.50 V
1.80 V
2.80 V
I
= 50 mA
= 1.0 mA
out
3.00 V
5.00 V
50
0
50
0
I
out
-40 -20
0
20
40
60
80
100 120
-40 -20
0
20
40
60
80
100 120
T , TEMPERATURE (°C)
A
T , TEMPERATURE (°C)
A
Figure 13. Dropout Voltage vs. Temperature
(Over Current Range)
Figure 14. Dropout Voltage vs. Temperature
(Over Output Voltage)
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
800
750
700
I
= 0 mA
out
5.0 V
3.3 V
C
= 1.0 mF
out
T = 25°C
A
ENABLE = V
in
Enable Increasing
Enable Decreasing
3.0 V
2.80 V
1.80 V
1.5 V
650
600
1.25 V
V
in
= 5.5 V
0.5
0
0
1.0
2.0
3.0
4.0
5.0
6.0
-40
-15
10
35
60
85
110 125
V , INPUT VOLTAGE (V)
in
T , TEMPERATURE (°C)
A
Figure 15. Output Voltage vs. Input Voltage
Figure 16. Enable Threshold vs. Temperature
http://onsemi.com
7
NCP603
TYPICAL CHARACTERISTICS
6.0
5.0
4.0
3.0
2.0
154
146
I
= 1.0 mA
= 150 mA
out
I
out
V
= 5.0 V
out
138
130
122
114
106
V
out
= 1.25 V
I
= 1.0 mA
= 150 mA
out
ENABLE = 0 V
I
out
1.0
0
98
90
ENABLE = 0.9 V
-40
-15
10
35
60
85
110 125
-40 -20
0
20
40
60
80
100 120
T , TEMPERATURE (°C)
A
T , TEMPERATURE (°C)
A
Figure 17. Ground Current (Sleep Mode) vs.
Temperature
Figure 18. Ground Current (Run Mode) vs.
Temperature
160
140
120
100
80
106
105
104
103
102
101
100
3.0 V
2.8 V
1.5 V
5.0 V
3.3 V
1.8 V
1.25 V
60
40
V
= ADJ
= 1.75 V
out
20
0
99
98
V
in
0
1.0
2.0
3.0
4.0
5.0
6.0
0
25
50
, OUTPUT CURRENT (mA)
out
75
100
125
150
V , INPUT VOLTAGE (V)
in
I
Figure 19. Ground Current vs. Input Voltage
Figure 20. Ground Current vs. Output Current
400
300
200
100
0
-40 -20
0
20
40
60
80
100 120
T , TEMPERATURE (°C)
A
Figure 21. ADJ Input Bias Current vs.
Temperature
http://onsemi.com
8
NCP603
TYPICAL CHARACTERISTICS
650
600
700
600
500
400
300
200
550
500
450
100
0
-40 -20
0
20
40
60
80
100 120
0
1.0
2.0
3.0
4.0
5.0
6.0
T , TEMPERATURE (°C)
A
V , INPUT VOLTAGE (V)
in
Figure 22. Output Short Circuit Current vs.
Temperature
Figure 23. Current Limit vs. Input Voltage
4.0
3.0
2.0
5.0
4.0
3.0
2.0
1.0
0
1.0
0
V
I
= (V + 0.5 V) to 6.0 V
out
= 1.0 mA
in
I
= 1.0 mA to 150 mA
out
out
-40 -20
0
20
40
60
80
100 120
-40
-15
10
35
60
85
110 125
T , TEMPERATURE (°C)
A
T , TEMPERATURE (°C)
A
Figure 24. Line Regulation vs. Temperature
Figure 25. Load Regulation vs. Temperature
45
40
35
30
25
20
80
70
60
50
40
30
20
1.25 V
3.3 V
5.0 V
5.0 V
3.0 V
1.5 V
V
V
= V + 1.0 V
out
= 0.5 V
in
ripple
p-p
1.25 V (ADJ)
15
10
C
= 1.0 mF
= 1.0 mA to 150 mA
out
10
0
I
out
-40 -20
0
20
40
60
80
100
120
0.1
1.0
10
100
T , TEMPERATURE (°C)
A
f, FREQUENCY (kHz)
Figure 26. Output Turn On Time vs.
Temperature
Figure 27. Power Supply Ripple Rejection vs.
Frequency
http://onsemi.com
9
NCP603
TYPICAL CHARACTERISTICS
10
V
out
= 5.0 V
Unstable Region
V
out
= 1.25 V
1.0
Stable Region
0.1
C
= 1.0 mF to 10 mF
out
T = -40°C to 125°C
A
V
in
= up to 6.0 V
0.01
0
25
50
75
100
125
150
I
, OUTPUT CURRENT (mA)
out
Figure 28. Output Stability with Output
Capacitor ESR over Output Current
V
out
= 1.25 V
Figure 29. Load Transient Response (1.0 mF)
V
out
= 1.25 V
Figure 30. Load Transient Response (10 mF)
http://onsemi.com
10
NCP603
DEFINITIONS
Load Regulation
Line Regulation
The change in output voltage for a change in output load
current at a constant temperature.
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse techniques such that the
average junction temperature is not significantly affected.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 2% below its
nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Line Transient Response
Typical output voltage overshoot and undershoot
response when the input voltage is excited with a given
slope.
Output Noise Voltage
Load Transient Response
This is the integrated value of the output noise over a
specified frequency range. Input voltage and output load
current are kept constant during the measurement. Results
Typical output voltage overshoot and undershoot
response when the output current is excited with a given
slope between no-load and full-load conditions.
are expressed in mV or nV √ Hz.
rms
Thermal Protection
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 175°C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Ground Current
Ground Current is the current that flows through the
ground pin when the regulator operates without a load on its
output (I
). This consists of internal IC operation, bias,
GND
etc. It is actually the difference between the input current
(measured through the LDO input pin) and the output load
current. If the regulator has an input pin that reduces its
internal bias and shuts off the output (enable/disable
Maximum Package Power Dissipation
The power dissipation level at which the junction
temperature reaches its maximum operating value.
function), this term is called the standby current (I
.)
STBY
APPLICATIONS INFORMATION
The NCP603 series regulator is self-protected with
output, there is no resistor divider. If the part is enabled
under no-load conditions, leakage current through the pass
transistor at junction temperatures above 85°C can approach
several microamperes, especially as junction temperature
approaches 150°C. If this leakage current is not directed into
a load, the output voltage will rise up to a level
approximately 20 mV above nominal.
The NCP603 contains an overshoot clamp circuit to
improve transient response during a load current step
release. When output voltage exceeds the nominal by
approximately 20 mV, this circuit becomes active and
clamps the output from further voltage increase. Tying the
internal thermal shutdown and internal current limit. Typical
application circuits are shown in Figures 2 and 3.
Input Decoupling (Cin)
A ceramic or tantalum 1.0 mF capacitor is recommended
and should be connected close to the NCP603 package.
Higher capacitance and lower ESR will improve the overall
line transient response.
Output Decoupling (Cout
)
The NCP603 is a stable component and does not require
a minimum Equivalent Series Resistance (ESR) for the
output capacitor. The minimum output decoupling value is
1.0 mF and can be augmented to fulfill stringent load
transient requirements. The regulator works with ceramic
chip capacitors as well as tantalum devices. Larger values
improve noise rejection and load regulation transient
response. Figure 28 shows the stability region for a range of
operating conditions and ESR values.
ENABLE pin to V will ensure that the part is active
in
whenever the supply voltage is present, thus guaranteeing
that the clamp circuit is active whenever leakage current is
present.
When the NCP603 adjustable regulator is disabled, the
overshoot clamp circuit becomes inactive and the pass
transistor leakage will charge any capacitance on V . If no
out
load is present, the output can charge up to within a few
millivolts of V . In most applications, the load will present
No-Load Regulation Considerations
in
some impedance to V such that the output voltage will be
The NCP603 adjustable regulator will operate properly
under conditions where the only load current is through the
resistor divider that sets the output voltage. However, in the
case where the NCP603 is configured to provide a 1.250 V
out
inherently clamped at a safe level. A minimum load of
10ꢁmA is recommended.
http://onsemi.com
11
NCP603
Noise Decoupling
Thermal
The NCP603 is a low noise regulator and needs no
external noise reduction capacitor. Unlike other low noise
regulators which require an external capacitor and have slow
startup times, the NCP603 operates without a noise
reduction capacitor, has a typical 15 ms start up delay and
As power in the NCP603 increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material, and the ambient temperature
affect the rate of junction temperature rise for the part. When
the NCP603 has good thermal conductivity through the
PCB, the junction temperature will be relatively low with
high power applications. The maximum dissipation the
NCP603 can handle is given by:
achieves a 50 mV overall noise level between 10 Hz and
rms
100 kHz.
Enable Operation
The enable pin will turn the regulator on or off. The
threshold limits are covered in the electrical characteristics
table in this data sheet. The turn-on/turn-off transient
voltage being supplied to the enable pin should exceed a
slew rate of 10 mV/ms to ensure correct operation. If the
enable function is not to be used then the pin should be
T
* T
A
J(MAX)
P
+
D(MAX)
(eq. 3)
R
qJA
Since T is not recommended to exceed 125_C (T
),
then the NCP603 can dissipate up to 465 mW when the
J
J(MAX)
ambient temperature (T ) is 25_C and the device is
A
assembled on 1 oz PCB with 645 mm area.
connected to V .
in
2
Output Voltage Adjust
The power dissipated by the NCP603 can be calculated
from the following equations:
The output voltage can be adjusted from 1 times
(Figureꢁ2) to 4 times (Figure 3) the typical 1.250 V
regulation voltage via the use of resistors between the output
and the ADJ input. The output voltage and resistors are
chosen using Equation 1 and Equation 2.
P
D
[ V (I
) ) I (V * V )
OUT IN OUT
IN GND@IOUT
(eq. 4)
(eq. 5)
or
P
) (V
OUT
I
)
OUT
D(MAX)
R1
+ 1.250ꢀǒ1 ) Ǔ) (I
V
[
IN(MAX)
V
OUT
R1)
(eq. 1)
I
) I
GND
ADJ
OUT
R2
[V
(I
* R1)]
out * ADJ
1.25
V
out
1.25
ƪ
* 1ƫ
(eq. 2)
R1 + R2 * ƪ
* 1ƫ^ R2ꢀ
Hints
V and GND printed circuit board traces should be as
in
wide as possible. When the impedance of these traces is
high, there is a chance to pick up noise or cause the regulator
to malfunction. Place external components, especially the
output capacitor, as close as possible to the NCP603, and
make traces as short as possible.
Input bias current I
is typically less than 150 nA.
ADJ
Choose R2 arbitrarily t minimize errors due to the bias
current and to minimize noise contribution to the output
voltage. Use Equation 2 to find the required value for R1.
DEVICE ORDERING INFORMATION
Device
NCP603SNADJT1G
Marking Code
AAU
Version
ADJ
Package
Shipping*
NCP603SN130T1G
NCP603SN150T1G
NCP603SN180T1G
NCP603SN280T1G
NCP603SN300T1G
NCP603SN330T1G
NCP603SN350T1G
NCP603SN500T1G
AAF
1.3 V
1.5 V
1.8 V
2.8 V
3.0 V
3.3 V
3.5 V
5.0 V
AAV
AAW
AAX
TSOP-5
(Pb-Free)
3000/Tape & Reel
AAY
AAZ
AA2
AA3
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting
Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
12
NCP603
PACKAGE DIMENSIONS
TSOP-5
CASE 483-02
ISSUE G
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES
LEAD FINISH THICKNESS. MINIMUM LEAD
THICKNESS IS THE MINIMUM THICKNESS
OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
5. OPTIONAL CONSTRUCTION: AN
ADDITIONAL TRIMMED LEAD IS ALLOWED
IN THIS LOCATION. TRIMMED LEAD NOT TO
EXTEND MORE THAN 0.2 FROM BODY.
NOTE 5
5X
D
0.20 C A B
2X
2X
0.10
T
T
M
5
4
3
0.20
B
S
1
2
K
L
DETAIL Z
G
A
MILLIMETERS
DIM
A
B
MIN
3.00 BSC
1.50 BSC
MAX
DETAIL Z
J
C
D
0.90
0.25
1.10
0.50
C
SEATING
PLANE
0.05
G
H
J
K
L
0.95 BSC
H
0.01
0.10
0.20
1.25
0
0.10
0.26
0.60
1.55
10
3.00
T
M
S
_
_
2.50
SOLDERING FOOTPRINT*
1.9
0.074
0.95
0.037
2.4
0.094
1.0
0.039
0.7
0.028
mm
inches
ǒ
Ǔ
SCALE 10:1
*For additional information on our Pb-Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800-282-9855 Toll Free
ꢁUSA/Canada
Europe, Middle East and Africa Technical Support:
ꢁPhone: 421 33 790 2910
Japan Customer Focus Center
ꢁPhone: 81-3-5773-3850
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
ꢁLiterature Distribution Center for ON Semiconductor
ꢁP.O. Box 5163, Denver, Colorado 80217 USA
ꢁPhone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada
ꢁFax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada
ꢁEmail: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
NCP603/D
相关型号:
NCP603SN330T1G
300 mA High Performance CMOS LDO Regulator with Enable and Enhanced ESD Protection
ONSEMI
NCP603SN350T1G
300 mA High Performance CMOS LDO Regulator with Enable and Enhanced ESD Protection
ONSEMI
NCP603SN500T1G
300 mA High Performance CMOS LDO Regulator with Enable and Enhanced ESD Protection
ONSEMI
NCP603SNADJT1G
300 mA High Performance CMOS LDO Regulator with Enable and Enhanced ESD Protection
ONSEMI
NCP605
500mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection
ONSEMI
NCP605MN15T2G
500mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection
ONSEMI
NCP605MN18T2G
500mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection
ONSEMI
NCP605MN25T2G
500mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection
ONSEMI
NCP605MN28T2G
500mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection
ONSEMI
NCP605MN30T2G
500mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection
ONSEMI
NCP605MN33T2G
500mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection
ONSEMI
©2020 ICPDF网 联系我们和版权申明