CAT5409WI-00-TE13_技术文档

CAT5409

Quad Digital

Potentiometer (POT)

with 64 Taps

and I²C Interface

Description

http://onsemi.com

The CAT5409 is four digital POTs integrated with control logic and

16 bytes of NVRAM memory.

A separate 6-bit control register (WCR) independently controls the

wiper tap position for each digital POT. Associated with each wiper

control register are four 6-bit non-volatile memory data registers (DR)

used for storing up to four wiper settings. Writing to the wiper control

TSSOP24

Y SUFFIX

CASE 948AR

SOIC−24

W SUFFIX

CASE 751BK

2

register or any of the non-volatile data registers is via a I C serial bus.

On power-up, the contents of the first data register (DR0) for each of

the four potentiometers is automatically loaded into its respective

wiper control register (WCR).

The Write Protection (WP) pin protects against inadvertent

programming of the data register.

PIN CONNECTIONS

V

CC

NC

1

The CAT5409 can be used as a potentiometer or as a two terminal,

variable resistor. It is intended for circuit level or system level

adjustments in a wide variety of applications.

R

L0

L3

H3

W3

0

R

H0

R

W0

A

2

Features

WP

NC

CAT5409

 Four Linear Taper Digital Potentiometers

 64 Resistor Taps per Potentiometer

SDA

A

3

A

SCL

1

R

 End to End Resistance 2.5 kW, 10 kW, 50 kW or 100 kW

 I C Interface

 Low Wiper Resistance, Typically 80 W

 Four Non-volatile Wiper Settings for Each Potentiometer

 Recall of Saved Wiper Settings at Power-up

 2.5 to 6.0 Volt Operation

L1

H1

L2

2

R

H2

R

W1

W2

GND

NC

SOIC−24 (W)

(Top View)

WP

 Standby Current less than 1 mA

SDA

1

A

2

A

1

 1,000,000 Nonvolatile WRITE Cycles

 100 Year Nonvolatile Memory Data Retention

 24-lead SOIC and 24-lead TSSOP

R

V

R

W0

H0

L0

L1

H1

R

W1

GND

NC

CC

 Write Protection for Data Register

CAT5409

NC

 These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS

R

A

R

SCL

L3

W2

Compliant

H3

W3

H2

L2

0

NC

A

3

TSSOP−24 (Y)

(Top View)

ORDERING INFORMATION

See detailed ordering and shipping information in the package

dimensions section on page 13 of this data sheet.

 Semiconductor Components Industries, LLC, 2013

1

Publication Order Number:

July, 2013 − Rev. 15

CAT5409/D

CAT5409

MARKING DIAGRAMS

(SOIC−24)

(TSSOP−24)

L3B

CAT5409WT

−RRYMXXXX

RLB

CAT5409YT

3YMXXX

L = Assembly Location

3 = Lead Finish − Matte-Tin

B = Product Revision (Fixed as “B”)

CAT = Fixed as “CAT”

5409W = Device Code

T = Temperature Range (I = Industrial)

− = Dash

RR = Resistance

25 = 2.5 KW

10 = 10 KW

50 = 50 KW

R = Resistance

1 = 2.5 KW

2 = 10 KW

4 = 50 KW

5 = 100 KW

L = Assembly Location

B = Product Revision (Fixed as “B”)

CAT5409Y = Device Code

T = Temperature Range (I = Industrial)

3 = Lead Finish − Matte-Tin

Y = Production Year (Last Digit)

M = Production Month (1−9, O, N, D)

XXX = Last Three Digits of Assembly Lot Number

00 = 100 KW

Y = Production Year (Last Digit)

M = Production Month (1−9, O, N, D)

XXXX = Last Four Digits of Assembly Lot Number

R

H3

H0

H1

H2

WIPER

2

I C BUS

SCL

SDA

CONTROL

REGISTERS

R

W0

W1

W2

INTERFACE

WP

A

0

A

1

A

2

A

3

NONVOLATILE

DATA

REGISTERS

CONTROL

LOGIC

W3

R

L3

L0

L1

L2

Figure 1. Functional Diagram

http://onsemi.com

2

CAT5409

PIN DESCRIPTIONS

SCL: Serial Clock

The CAT5409 serial clock input pin is used to clock all

data transfers into or out of the device.

Table 1. PIN DESCRIPTIONS

Pin#

(TSSOP)

(SOIC)

Name

Function

Supply Voltage

SDA: Serial Data

19

20

1

2

V

CC

The CAT5409 bidirectional serial data pin is used to

transfer data into and out of the device. The SDA pin is an

open drain output and can be wire-Ored with the other open

drain or open collector outputs.

R

Low Reference Terminal

for Potentiometer 0

L0

H0

W0

21

22

3

4

R

High Reference Terminal

for Potentiometer 0

A0, A1, A2, A3: Device Address Inputs

R

Wiper Terminal for

Potentiometer 0

These inputs set the device address when addressing

multiple devices. A total of sixteen devices can be addressed

on a single bus. A match in the slave address must be made

with the address input in order to initiate communication

with the CAT5409.

23

24

1

5

6

7

8

9

A2

Device Address

WP

SDA

A1

Write Protection

Serial Data Input/Output

Device Address

2

R , R : Resistor End Points

H

L

3

R

Low Reference Terminal

for Potentiometer 1

L1

H1

W1

The four sets of R and R pins are equivalent to the

terminal connections on a mechanical potentiometer.

H

L

4

5

10

11

R

High Reference Terminal

for Potentiometer 1

R : Wiper

W

The four R pins are equivalent to the wiper terminal of

W

R

Wiper Terminal for

Potentiometer 1

a mechanical potentiometer.

WP: Write Protect Input

6

7

8

12

13

14

GND

NC

Ground

The WP pin when tied low prevents non-volatile writes to

the data registers (change of wiper control register is

allowed) and when tied high or left floating normal

read/write operations are allowed. See Write Protection on

page 8 for more details.

No Connect

R

W2

Wiper Terminal for

Potentiometer 2

9

15

16

R

High Reference Terminal

for Potentiometer 2

H2

10

R

Low Reference Terminal

for Potentiometer 2

L2

11

12

13

14

15

17

18

19

20

21

SCL

A3

Bus Serial Clock

Device Address

No Connect

NC

A0

Device Address, LSB

R

W3

Wiper Terminal for

Potentiometer 3

16

17

18

22

23

24

R

High Reference Terminal

for Potentiometer 3

H3

R

Low Reference Terminal

for Potentiometer 3

L3

NC

No Connect

DEVICE OPERATION

2

The CAT5409 is four resistor arrays integrated with I C

serial interface logic, four 6-bit wiper control registers and

sixteen 6-bit, non-volatile memory data registers. Each

resistor array contains 63 separate resistive elements

connected in series. The physical ends of each array are

equivalent to the fixed terminals of a mechanical

point for each potentiometer is connected to its wiper

terminal at a time and is determined by the value of the wiper

control register. Data can be read or written to the wiper

control registers or the non-volatile memory data registers

2

via the I C bus. Additional instructions allows data to be

transferred between the wiper control registers and each

respective potentiometer’s non-volatile data registers. Also,

the device can be instructed to operate in an “increment/

decrement” mode.

potentiometer (R and R ). R and R are symmetrical and

H

L

H

L

may be interchanged. The tap positions between and at the

ends of the series resistors are connected to the output wiper

terminals (R ) by a CMOS transistor switch. Only one tap

W

http://onsemi.com

3

CAT5409

Table 2. ABSOLUTE MAXIMUM RATINGS

Parameters

Ratings

Units

C

V

Temperature Under Bias

Storage Temperature

−55 to +125

−65 to +150

Voltage on Any Pin with Respect to V (Notes 1, 2)

−2.0 to +V + 2.0

SS

CC

V

with Respect to Ground

−2.0 to +7.0

1.0

V

CC

Package Power Dissipation Capability (T = 25C)

W

A

Lead Soldering Temperature (10 s)

Wiper Current

300

C

mA

12

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the

Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect

device reliability.

1. The minimum DC input voltage is –0.5 V. During transitions, inputs may undershoot to –2.0 V for periods of less than 20 ns. Maximum DC

voltage on output pins is V +0.5 V, which may overshoot to V +2.0 V for periods of less than 20 ns.

CC

2. Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1 V to V +1 V.

CC

Table 3. RECOMMENDED OPERATING CONDITIONS

Parameters

Ratings

Units

V

CC

+2.5 to +6

Industrial Temperature

−40 to +85

C

Table 4. POTENTIOMETER CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)

Symbol

Parameter

Test Conditions

Min

Typ

100

50

Max

Units

kW

%

R

Potentiometer Resistance (−00)

Potentiometer Resistance (−50)

Potentiometer Resistance (−10)

Potentiometer Resistance (−2.5)

Potentiometer Resistance Tolerance

POT

10

2.5

20

1

R

Matching

%

POT

Power Rating

25C, each pot

50

mW

mA

W

I

W

Wiper Current

6

R

Wiper Resistance

I

= 3 mA @ V = 3 V

300

150

W

CC

= 3 mA @ V = 5 V

80

W

CC

V

TERM

Voltage on any R or R Pin

V

SS

= 0 V

GND

V

CC

V

H

L

Resolution

1.6

%

Absolute Linearity (Note 4)

Relative Linearity (Note 5)

Temperature Coefficient of R

R

− R

1

LSB

W(n)(actual)

(n)(expected)

(Note 7)

(Note 6)

R

W(n+1)

− [R ]

W(n) + LSB

0.2

LSB

(Note 6)

(Note 7)

(Note 3)

TC

300

ppm/C

pF

RPOT

POT

TC

Ratiometric Temp. Coefficient

Potentiometer Capacitances

Frequency Response

20

RATIO

C /C /C

H

10/10/25

0.4

L

W

fc

R

= 50 kW (Note 3)

MHz

POT

3. This parameter is tested initially and after a design or process change that affects the parameter.

4. Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a

potentiometer.

5. Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentiometer.

It is a measure of the error in step size.

6. LSB = R

/ 63 or (R − R ) / 63, single pot.

TOT

H L

7. n = 0, 1, 2, ..., 63

http://onsemi.com

4

CAT5409

Table 5. D.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)

Symbol

Parameter

Power Supply Current

Test Conditions

= 400 kHz

Min

Max

1

Units

mA

V

I

f

SCL

CC

I

SB

Standby Current (V = 5 V)

V

IN

= GND or V , SDA Open

1

CC

I

LI

Input Leakage Current

Output Leakage Current

Input Low Voltage

V

IN

= GND to V

CC

10

I

LO

V

= GND to V

CC

OUT

V

IL

−1

V

x 0.3

CC

V

IH

Input High Voltage

V

x 0.7

V

+ 1.0

V

CC

V

OL1

Output Low Voltage (V = 3 V)

I

OL

= 3 mA

0.4

V

CC

Table 6. CAPACITANCE (Note 8) (T = 25C, f = 1.0 MHz, V = 5 V)

A

CC

Symbol

Test

Conditions

Max

8

Units

pF

C

Input/Output Capacitance (SDA)

V

I/O

= 0 V

I/O

C

Input Capacitance (A0, A1, A2, A3, SCL, WP)

V

IN

6

pF

IN

8. This parameter is tested initially and after a design or process change that affects the parameter.

Table 7. A.C. CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)

Symbol

Parameter

Min

Typ

Max

Units

kHz

ns

f

Clock Frequency

400

50

SCL

T (Note 10)

Noise Suppression Time Constant at SCL, SDA Inputs

SLC Low to SDA Data Out and ACK Out

Time the bus must be free before a new transmission can start

Start Condition Hold Time

I

t

AA

0.9

ms

t

(Note 10)

1.2

0.6

1.2

0.6

0

ms

BUF

t

ms

HD:STA

t

Clock Low Period

ms

LOW

t

Clock High Period

ms

HIGH

t

Start Condition SetupTime (for a Repeated Start Condition)

Data in Hold Time

ms

SU:STA

HD:DAT

t

ns

t

Data in Setup Time

100

ns

SU:DAT

t

R

(Note 10)

SDA and SCL Rise Time

0.3

ms

t (Note 10)

F

SDA and SCL Fall Time

300

ns

t

Stop Condition Setup Time

0.6

50

ms

SU:STO

t

Data Out Hold Time

ns

DH

Table 8. POWER UP TIMING (Note 10)

Symbol

Parameter

Max

1

Units

ms

t

Power-up to Read Operation

Power-up to Write Operation

PUR

t

1

ms

PUW

Table 9. WRITE CYCLE LIMITS (Note 9)

Symbol

Max

Units

t

Write Cycle Time

5

ms

WR

9. The write cycle is the time from a valid stop condition of a write sequence to the end of the internal program/erase cycle. During the write

cycle, the bus interface circuits are disabled, SDA is allowed to remain high, and the device does not respond to its slave address.

http://onsemi.com

5

CAT5409

Table 10. RELIABILITY CHARACTERISTICS

Symbol

(Note 10)

Parameter

Endurance

Reference Test Method

MIL−STD−883, Test Method 1033

MIL−STD−883, Test Method 1008

MIL−STD−883, Test Method 3015

JEDEC Standard 17

Min

1,000,000

100

Max

Units

Cycles/Byte

Years

N

END

T

(Note 10)

Data Retention

ESD Susceptibility

Latch-up

DR

V

2000

V

ZAP

I

(Notes 10, 11)

100

mA

LTH

10.This parameter is tested initially and after a design or process change that affects the parameter.

11. t_PURand t_PUWare delays required from the time V is stable until the specified operation can be initiated.

CC

t

F

t

R

HIGH

t

LOW

SCL

t

HD:DAT

SU:STA

t

SU:STO

SU:DAT

HD:STA

SDA IN

BUF

t

DH

AA

SDA OUT

Figure 2. Bus Timing

SCL

SDA

8TH BIT

BYTE n

ACK

t

WR

STOP

START

ADDRESS

CONDITION

Figure 3. Write Cycle Timing

SDA

SCL

START CONDITION

STOP CONDITION

Figure 4. Start/Stop Timing

http://onsemi.com

6

CAT5409

SERIAL BUS PROTOCOL

2

START Condition

The following defines the features of the I C bus protocol:

1. Data transfer may be initiated only when the bus is

not busy.

The START Condition precedes all commands to the

device, and is defined as a HIGH to LOW transition of SDA

when SCL is HIGH. The CAT5409 monitors the SDA and

SCL lines and will not respond until this condition is met.

2. During a data transfer, the data line must remain

stable whenever the clock line is high. Any

changes in the data line while the clock is high

will be interpreted as a START or STOP condition.

STOP Condition

A LOW to HIGH transition of SDA when SCL is HIGH

determines the STOP condition. All operations must end

with a STOP condition.

The device controlling the transfer is a master, typically a

processor or controller, and the device being controlled is the

slave. The master will always initiate data transfers and

provide the clock for both transmit and receive operations.

Therefore, the CAT5409 will be considered a slave device

in all applications.

DEVICE ADDRESSING

Acknowledge

The bus Master begins a transmission by sending a

START condition. The Master then sends the address of the

particular slave device it is requesting. The four most

significant bits of the 8−bit slave address are fixed as 0101

for the CAT5409 (see Figure 6). The next four significant

bits (A3, A2, A1, A0) are the device address bits and define

which device the Master is accessing. Up to sixteen devices

may be individually addressed by the system. Typically,

+5 V and ground are hard-wired to these pins to establish the

device’s address.

After a successful data transfer, each receiving device is

required to generate an acknowledge. The Acknowledging

device pulls down the SDA line during the ninth clock cycle,

signaling that it received the 8 bits of data.

The CAT5409 responds with an acknowledge after

receiving a START condition and its slave address. If the

device has been selected along with a write operation, it

responds with an acknowledge after receiving each 8-bit

byte.

When the CAT5409 is in a READ mode it transmits 8 bits

of data, releases the SDA line, and monitors the line for an

acknowledge. Once it receives this acknowledge, the

CAT5409 will continue to transmit data. If no acknowledge

is sent by the Master, the device terminates data transmission

and waits for a STOP condition.

After the Master sends a START condition and the slave

address byte, the CAT5409 monitors the bus and responds

with an acknowledge (on the SDA line) when its address

matches the transmitted slave address.

SCL FROM

MASTER

1

8

9

DATA OUTPUT

FROM TRANSMITTER

DATA OUTPUT

FROM RECEIVER

START

ACKNOWLEDGE

Figure 5. Acknowledge Timing

http://onsemi.com

7

CAT5409

WRITE OPERATIONS

In the Write mode, the Master device sends the START

CAT5409 initiates the internal write cycle. ACK polling can

be initiated immediately. This involves issuing the start

condition followed by the slave address. If the CAT5409 is

still busy with the write operation, no ACK will be returned.

If the CAT5409 has completed the write operation, an ACK

will be returned and the host can then proceed with the next

instruction operation.

condition and the slave address information to the Slave

device. After the Slave generates an acknowledge, the

Master sends the instruction byte that defines the requested

operation of CAT5409. The instruction byte consist of a

four-bit opcode followed by two register selection bits and

two pot selection bits. After receiving another acknowledge

from the Slave, the Master device transmits the data to be

written into the selected register. The CAT5409

acknowledges once more and the Master generates the

STOP condition, at which time if a non-volatile data register

is being selected, the device begins an internal programming

cycle to non-volatile memory. While this internal cycle is in

progress, the device will not respond to any request from the

Master device.

Write Protection

The Write Protection feature allows the user to protect

against inadvertent programming of the non-volatile data

registers. If the WP pin is tied to LOW, the data registers are

protected and become read only. Similarly, the WP pin going

low after start but after start will interrupt non−volatile write

to data registers, while the WP pin going low after internal

write cycle has started, will have no effect on any write

operation. The CAT5409 will accept both slave addresses

and instructions, but the data registers are protected from

programming by the device’s failure to send an

acknowledge after data is received.

Acknowledge Polling

The disabling of the inputs can be used to take advantage

of the typical write cycle time. Once the stop condition is

issued to indicate the end of the host’s write operation, the

CAT5409

0

1

0

1

A3

A2

A1

A0

* A0, A1, A2 and A3 correspond to pin A0, A1, A2 and A3 of the device.

** A0, A1, A2 and A3 must compare to its corresponding hard wired input pins.

Figure 6. Slave Address Bits

INSTRUCTION

BYTE

S

T

A

R

T

SLAVE

S

T

ADDRESS

BUS ACTIVITY:

MASTER

O

P

DR1 WCRDATA

Fixed Variable

SDA LINE

S

P

A

C

K

A

C

K

A

C

K

Figure 7. Write Timing

http://onsemi.com

8

CAT5409

INSTRUCTION AND REGISTER DESCRIPTION

Instruction Byte

Slave Address Byte

The first byte sent to the CAT5409 from the master/

processor is called the Slave Address Byte. The most

significant four bits of the Device Type address are a device

type identifier. These bits for the CAT5409 are fixed at

0101[B] (refer to Figure 8).

The next four bits, A3 − A0, are the internal slave address

and must match the physical device address which is defined

by the state of the A3 − A0 input pins for the CAT5409 to

successfully continue the command sequence. Only the

device which slave address matches the incoming device

address sent by the master executes the instruction. The A3

− A0 inputs can be actively driven by CMOS input signals

The next byte sent to the CAT5409 contains the

instruction and register pointer information. The four most

significant bits used provide the instruction opcode I [3:0].

The R1 and R0 bits point to one of the four data registers of

each associated potentiometer. The least two significant bits

point to one of four Wiper Control Registers. The format is

shown in Figure 9.

Table 11. DATA REGISTER SELECTION

Data Register Selected

R1

0

R0

0

DR0

DR1

DR2

DR3

0

1

or tied to V or V

.

SS

CC

1

0

1

Device Type

Identifier

Slave Address

ID3

0

ID2

ID1

ID0

A3

A2

A1

A0

1

0

1

(MSB)

(LSB)

Figure 8. Identification Byte Format

Instruction

Opcode

Data Register

Selection

WCR/Pot Selection

I3

I2

I1

I0

R1

R0

P1

P0

(MSB)

(LSB)

Figure 9. Instruction Byte Format

WIPER CONTROL AND DATA REGISTERS

Data Registers (DR)

Wiper Control Register (WCR)

The CAT5409 contains four 6-bit Wiper Control

Registers, one for each potentiometer. The Wiper Control

Register output is decoded to select one of 64 switches along

its resistor array. The contents of the WCR can be altered in

four ways: it may be written by the host via Write Wiper

Control Register instruction; it may be written by

transferring the contents of one of four associated Data

Registers via the XFR Data Register instruction, it can be

modified one step at a time by the Increment/Decrement

instruction (see Instruction section for more details).

Finally, it is loaded with the content of its data register zero

(DR0) upon power-up.

The Wiper Control Register is a volatile register that loses

its contents when the CAT5409 is powered-down. Although

the register is automatically loaded with the value in DR0

upon power-up, this may be different from the value present

at power-down.

Each potentiometer has four 6-bit non-volatile Data

Registers. These can be read or written directly by the host.

Data can also be transferred between any of the four Data

Registers and the associated Wiper Control Register. Any

data changes in one of the Data Registers is a non-volatile

operation and will take a maximum of 5 ms.

If the application does not require storage of multiple

settings for the potentiometer, the Data Registers can be used

as standard memory locations for system parameters or user

preference data.

Instructions

Four of the nine instructions are three bytes in length.

These instructions are:

 Read Wiper Control Register – read the current wiper

position of the selected potentiometer in the WCR

 Write Wiper Control Register – change current wiper

position in the WCR of the selected potentiometer

http://onsemi.com

9

CAT5409

 Read Data Register – read the contents of the selected

 Write Data Register – write a new value to the

Data Register

selected Data Register

Table 12. INSTRUCTION SET (Note: 1/0 = data is one or zero)

Instruction Set

I3

I2

I1

I0

R1

R0

WCR1/ P1

WCR0/ P0

Instruction

Operation

Read Wiper

Control Register

1

0

1

0

1/0

Read the contents of the Wiper Control

Register pointed to by P1−P0

Write Wiper Control

Register

1

0

1

0

1

0

1

0

1/0

Write new value to the Wiper Control

Register pointed to by P1−P0

Read Data

Register

1/0

Read the contents of the Data Register

pointed to by P1−P0 and R1−R0

Write Data Register

Write new value to the Data Register

pointed to by P1−P0 and R1−R0

XFR Data Register

to Wiper Control

Register

Transfer the contents of the Data

Register pointed to by P1−P0 and

R1−R0 to its associated Wiper Control

Register

XFR Wiper Control

Register to Data

Register

1

0

1

0

1

0

1

1/0

0

1/0

0

Transfer the contents of the Wiper

Control Register pointed to by P1−P0 to

the Data Register pointed to by R1−R0

Gang XFR Data

Registers to Wiper

Control Registers

Transfer the contents of the Data

Registers pointed to by R1−R0 of all four

pots to their respective Wiper Control

Registers

Gang XFR Wiper

Control Registers

to Data Register

1

0

1

0

1/0

0

1/0

0

Transfer the contents of both Wiper

Control Registers to their respective data

Registers pointed to by R1−R0 of all four

pots

Increment/

Decrement Wiper

Control Register

1/0

Enable Increment/decrement of the

Control Latch pointed to by P1−P0

The basic sequence of the three byte instructions is

illustrated in Figure 11. These three-byte instructions

exchange data between the WCR and one of the Data

Registers. The WCR controls the position of the wiper. The

 Global XFR Data Register to Wiper Control

Register

This transfers the contents of all specified Data

Registers to the associated Wiper Control Registers.

 Global XFR Wiper Counter Register to Data

Register

response of the wiper to this action will be delayed by t

.

WRL

A transfer from the WCR (current wiper position), to a Data

Register is a write to non-volatile memory and takes a

This transfers the contents of all Wiper Control

Registers to the specified associated Data Registers.

minimum of t

to complete. The transfer can occur

WR

between one of the four potentiometers and one of its

associated registers; or the transfer can occur between all

potentiometers and one associated register.

Four instructions require a two-byte sequence to

complete, as illustrated in Figure 10. These instructions

transfer data between the host/processor and the CAT5409;

either between the host and one of the data registers or

directly between the host and the Wiper Control Register.

These instructions are:

Increment/Decrement Command

The final command is Increment/Decrement (Figures 6

and 12). The Increment/Decrement command is different

from the other commands. Once the command is issued and

the CAT5409 has responded with an acknowledge, the

master can clock the selected wiper up and/or down in one

segment steps; thereby providing a fine tuning capability to

the host. For each SCL clock pulse (t

) while SDA is

HIGH

HIGH, the selected wiper will move one resistor segment

 XFR Data Register to Wiper Control Register

This transfers the contents of one specified Data

Register to the associated Wiper Control Register.

 XFR Wiper Control Register to Data Register

This transfers the contents of the specified Wiper

Control Register to the specified associated Data

Register.

towards the R terminal. Similarly, for each SCL clock

H

pulse while SDA is LOW, the selected wiper will move one

resistor segment towards the R terminal.

L

See Instructions format for more detail.

http://onsemi.com

10

CAT5409

0

1

0

1

SDA

ID3 ID2 ID1 ID0

S

T

A

C

K

A3 A2 A1 A0

I3 I2 I1 I0

S

T

A

R

T

A

C

K

R1 R0 P1 P0

Register

O

P

Internal

Address

Instruction

Opcode

Device ID

Pot/WCR

Address

Figure 10. Two-byte Instruction Sequence

0

1

0

1

SDA

S

T

A

R

T

A

C

K

I3 I2 I1 I0

P1 P0

A

C

K

D7 D6 D5 D4 D3 D2 D1 D0

A

C

K

S

T

ID3 ID2 ID1 ID0

Device ID

R1 R0

A3 A2 A1 A0

O

P

Internal

Address

WCR[7:0]

or

Instruction

Opcode

Pot/WCR

Address

Data

Register

Address

Data Register D[7:0]

Figure 11. Three-byte Instruction Sequence

0

1

0

1

SDA

ID3 ID2 ID1 ID0

Device ID

I1

A3 A2 A1 A0

I3 I2

I0

R1 R0 P1 P0

S

A

C

K

A

C

I

D

E

C

1

S

T

I

D

E

C

n

T

A

R

T

N

C

1

N

C

2

N

C

n

Internal

Address

Instruction

Opcode

O

P

Pot/WCR K

Address

Data

Register

Address

Figure 12. Increment/Decrement Instruction Sequence

INC/DEC

Command

Issued

t

WRID

SCL

SDA

Voltage Out

R

W

Figure 13. Increment/Decrement Timing Limits

http://onsemi.com

11

CAT5409

INSTRUCTION FORMAT

Table 13. READ WIPER CONTROL REGISTER (WCR)

S

T

A

R

T

DEVICE ADDRESSES

A3 A2 A1 A0

A

C

K

INSTRUCTION

A

C

K

DATA

A

C

K

S

T

O

P

0

1

0

1

0

1

0

P1

P0

7

0

6

0

5

4

3

2

1

0

Table 14. WRITE WIPER CONTROL REGISTER (WCR)

S

T

A

R

T

DEVICE ADDRESSES

A3 A2 A1 A0

A

C

K

INSTRUCTION

A

C

K

DATA

A

C

K

S

T

O

P

0

1

0

1

0

1

0

7

0

6

0

4

3

Table 15. READ DATA REGISTER (DR)

S

T

A

R

T

DEVICE ADDRESSES

A3 A2 A1 A0

A

C

K

INSTRUCTION

R1 R0

A

C

K

DATA

A

C

K

S

T

O

P

0

1

0

1

7

0

6

0

4

3

Table 16. WRITE DATA REGISTER (DR)

S

T

A

R

T

DEVICE ADDRESSES

A3 A2 A1 A0

A

C

K

INSTRUCTION

R1 R0

A

C

K

DATA

A

C

K

S

T

O

P

0

1

0

1

0

7

0

6

0

4

3

Table 17. GLOBAL TRANSFER DATA REGISTER (DR) TO WIPER CONTROL REGISTER (WCR)

S

T

A

R

T

DEVICE ADDRESSES

A3 A2 A1 A0

A

C

K

INSTRUCTION

R1 R0

A

C

K

S

T

O

P

0

1

0

1

0

1

0

Table 18. GLOBAL TRANSFER WIPER CONTROL REGISTER (WCR) TO DATA REGISTER (DR)

S

T

A

R

T

DEVICE ADDRESSES

A3 A2 A1 A0

A

C

K

INSTRUCTION

R1 R0

A

C

K

S

T

O

P

0

1

0

1

0

Table 19. TRANSFER WIPER CONTROL REGISTER (WCR) TO DATA REGISTER (DR)

S

T

A

R

T

DEVICE ADDRESSES

A3 A2 A1 A0

A

C

K

INSTRUCTION

R1 R0

A

C

K

S

T

O

P

0

1

0

1

0

P1

P0

http://onsemi.com

12

CAT5409

Table 20. TRANSFER DATA REGISTER (DR) TO WIPER CONTROL REGISTER (WCR)

S

T

A

R

T

DEVICE ADDRESSES

A3 A2 A1 A0

A

C

K

INSTRUCTION

R1 R0

A

C

K

S

T

O

P

0

1

0

1

0

1

P1

P0

Table 21. INCREMENT (I)/DECREMENT (D) WIPER CONTROL REGISTER (WCR)

S

T

A

R

T

DEVICE ADDRESSES

A3 A2 A1 A0

A

C

K

INSTRUCTION

A

C

K

DATA

S

T

O

P

0

1

0

1

0

1

0

P1

P0

I/D

. . .

I/D

NOTE: Any write or transfer to the Non−volatile Data Registers is followed by a high voltage cycle after a STOP has been issued.

Table 22. ORDERING INFORMATION

†

Orderable Part Number

CAT5409WI−25−T1

CAT5409WI−10−T1

CAT5409WI−50−T1

CAT5409WI−00−T1

CAT5409YI−25−T2

CAT5409YI−10−T2

CAT5409YI−50−T2

CAT5409YI−00−T2

CAT5409WI25

Resistance (kW)

Lead Finish

Package

Shipping

2.5

10

SOIC−24

1,000 / Tape & Reel

2,000 / Tape & Reel

31 Units / Tube

50

100

2.5

10

TSSOP24

SOIC−24

TSSOP24

50

100

2.5

10

Matte-Tin

CAT5409WI10

CAT5409WI50

50

CAT5409WI00

100

2.5

10

CAT5409YI25

CAT5409YI10

62 Units / Tube

CAT5409YI50

50

CAT5409YI00

100

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging

Specifications Brochure, BRD8011/D.

12.For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device

Nomenclature document, TND310/D, available at www.onsemi.com.

13.All packages are RoHS-compliant (Pb-Free, Halogen Free).

14.The standard lead finish is Matte-Tin.

15.For additional package and temperature options, please contact your nearest ON Semiconductor Sales office.

http://onsemi.com

13

CAT5409

PACKAGE DIMENSIONS

SOIC−24, 300 mils

CASE 751BK

ISSUE O

SYMBOL

MIN

NOM

MAX

2.65

0.30

2.55

0.51

0.33

15.40

10.51

7.60

2.35

A

A1

A2

b

0.10

2.05

0.31

0.20

15.20

10.11

7.34

E1

E

c

D

E

E1

e

1.27 BSC

h

0.25

0.40

0º

0.75

1.27

8º

L

b

e

θ

PIN#1 IDENTIFICATION

5º

15º

θ1

TOP VIEW

h

D

h

q1

A2

q

A

q1

L

c

A1

SIDE VIEW

END VIEW

Notes:

(1) All dimensions are in millimeters. Angles in degrees.

(2) Complies with JEDEC MS-013.

http://onsemi.com

14

CAT5409

PACKAGE DIMENSIONS

TSSOP24, 4.4x7.8

CASE 948AR

ISSUE A

b

SYMBOL

MIN

NOM

MAX

A

A1

A2

b

1.20

0.15

1.05

0.30

0.20

7.90

6.55

4.50

0.05

0.80

0.19

0.09

7.70

6.25

4.30

c

E1

E

D

7.80

6.40

E

E1

e

4.40

0.65 BSC

0.60

L

0.50

0.70

L1

1.00 REF

0º

8º

θ

e

TOP VIEW

D

c

A2

A

θ1

L

A1

L1

SIDE VIEW

END VIEW

Notes:

(1) All dimensions are in millimeters. Angles in degrees.

(2) Complies with JEDEC MO-153.

ON Semiconductor and

are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,

copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC

reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any

particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without

limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications

and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC

does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for

surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where

personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and

its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,

any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture

of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

LITERATURE FULFILLMENT:

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5817−1050

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

For additional information, please contact your local

Sales Representative

CAT5409/D

http://onsemi.com

15


型号：	CAT5409WI-00-TE13
厂家：	ONSEMI
描述：	QUAD 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24, 0.300 INCH, LEAD AND HALOGEN FREE, SOIC-24 光电二极管转换器电阻器
文件：	总15页 (文件大小：197K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

CAT5409WI-00-TE13 [ONSEMI]

相关型号：

CAT5409WI-10

CAT5409WI-10

CAT5409WI-10-T1

CAT5409WI-10-T1

CAT5409WI-10-TE13

CAT5409WI-25

CAT5409WI-25

CAT5409WI-25-T1

CAT5409WI-25-T1

CAT5409WI-25-TE13

CAT5409WI-25-TE13

CAT5409WI-50