TJA1021T/20/C,118 [NXP]
TJA1021 - LIN 2.1/SAE J2602 transceiver SOIC 8-Pin;型号: | TJA1021T/20/C,118 |
厂家: | NXP |
描述: | TJA1021 - LIN 2.1/SAE J2602 transceiver SOIC 8-Pin 电信 光电二极管 电信集成电路 |
文件: | 总25页 (文件大小:571K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TJA1021
LIN 2.1/SAE J2602 transceiver
Rev. 7 — 25 March 2011
Product data sheet
1. General description
The TJA1021 is the interface between the Local Interconnect Network (LIN) master/slave
protocol controller and the physical bus in a LIN. It is primarily intended for in-vehicle
sub-networks using baud rates from 1 kBd up to 20 kBd and is LIN 2.1/SAE J2602
compliant. The TJA1021 is pin-to-pin compatible with the TJA1020 with an improved
ElectroStatic Discharge (ESD) specification.
The transmit data stream of the protocol controller at the transmit data input (TXD) is
converted by the TJA1021 into a bus signal with optimized slew rate and wave shaping to
minimize ElectroMagnetic Emission (EME). The LIN bus output pin is pulled HIGH via an
internal termination resistor. For a master application, an external resistor in series with a
diode should be connected between pin INH or pin VBAT and pin LIN. The receiver detects
the data stream at the LIN bus input pin and transfers it via pin RXD to the microcontroller.
In Sleep mode, the power consumption of the TJA1021 is very low. In failure modes, the
power consumption is reduced to a minimum.
2. Features and benefits
2.1 General
LIN 2.1/SAE J2602 compliant
Baud rate up to 20 kBd
Very low ElectroMagnetic Emission (EME)
High ElectroMagnetic Immunity (EMI)
Passive behavior in unpowered state
Input levels compatible with 3.3 V and 5 V devices
Integrated termination resistor for LIN slave applications
Wake-up source recognition (local or remote)
K-line compatible
Pin-to-pin compatible with TJA1020
Available in SO8 and HVSON8 packages
Leadless HVSON8 package (3.0 mm 3.0 mm) with improved Automated Optical
Inspection (AOI) capability
2.2 Low power management
Very low current consumption in Sleep mode with local and remote wake-up
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
2.3 Protection mechanisms
High ESD robustness: 6 kV according to IEC 61000-4-2 for pins LIN, VBAT and
WAKE_N
Transmit data (TXD) dominant time-out function
Bus terminal and battery pin protected against transients in the automotive
environment (ISO 7637)
Bus terminal short-circuit proof to battery and ground
Thermally protected
3. Quick reference data
Table 1.
Symbol Parameter
VBAT battery supply voltage
IBAT
Quick reference data
Conditions
Min
0.3
2
Typ
Max Unit
with respect to GND
-
+40
10
V
battery supply current
Sleep mode; VLIN = VBAT; VWAKE_N = VBAT
VTXD = 0 V; VSLP_N = 0 V
7
A
Standby mode; bus recessive
150
300
300
1
450
800
800
2
1000 A
1200 A
1600 A
VINH = VBAT; VLIN = VBAT; VWAKE_N = VBAT
VTXD = 0 V; VSLP_N = 0 V
Standby mode; bus dominant
VBAT = 12 V; VINH = 12 V; VLIN = 0 V
VWAKE_N = 12 V; VTXD = 0 V; VSLP_N = 0 V
Normal mode; bus recessive
VINH = VBAT; VLIN = VBAT; VWAKE_N = VBAT
VTXD = 5 V; VSLP_N = 5 V
Normal mode; bus dominant
4
mA
VBAT = 12 V; VINH = 12 V; VWAKE_N = 12 V
VTXD = 0 V; VSLP_N = 5 V
VLIN
Tvj
voltage on pin LIN
with respect to GND, VBAT and VWAKE_N
40
40
-
-
+40
V
virtual junction temperature
+150 C
4. Ordering information
Table 2.
Ordering information
Type number[1]
Package
Name
SO8
Description
plastic small outline package; 8 leads; body width 3.9 mm
Version
TJA1021T/10
TJA1021T/20
SOT96-1
TJA1021TK/10
TJA1021TK/20
HVSON8
plastic thermal enhanced very thin small outline package; no leads;
8 terminals; body 3 3 0.85 mm
SOT782-1
[1] TJA1021T/10 and TJA1021TK/10: for the low slope version that supports baud rates up to 10.4 kBd (SAE J2602);
TJA1021T/20 and TJA1021TK/20: for the normal slope version that supports baud rates up to 20 kBd.
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
2 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
5. Block diagram
7
V
BAT
WAKE-UP
TIMER
3
WAKE_N
CONTROL
8
INH
SLEEP/
NORMAL
TIMER
TEMPERATURE
PROTECTION
2
4
SLP_N
TXD
6
LIN
TXD
TIME-OUT
TIMER
TJA1021
BUS
TIMER
1
RXD
RXD/
INT
5
FILTER
GND
001aae066
Fig 1. Block diagram
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
3 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
6. Pinning information
6.1 Pinning
terminal 1
index area
1
2
3
4
8
7
6
5
RXD
SLP_N
WAKE_N
TXD
INH
V
BAT
TJA1021TK
1
2
3
4
8
7
6
5
RXD
INH
LIN
SLP_N
WAKE_N
TXD
V
BAT
TJA1021T
GND
LIN
GND
015aaa232
Transparent top view
015aaa231
a. TJA1021T/10; TJA1021T/20: SO8
b. TJA1021TK/10; TJA1021TK/20:
HVSON8
Fig 2. Pin configuration diagrams
6.2 Pin description
Table 3.
Symbol
Pin description
Pin
Description
RXD
1
2
receive data output (open-drain); active LOW after a wake-up event
SLP_N
sleep control input (active LOW); controls inhibit output; resets
wake-up source flag on TXD and wake-up request on RXD
WAKE_N
TXD
3
local wake-up input (active LOW); negative edge triggered
transmit data input; active LOW output after a local wake-up event
ground
4
5[1]
GND
LIN
6
LIN bus line input/output
VBAT
7
battery supply voltage
INH
8
battery related inhibit output for controlling an external voltage
regulator; active HIGH after a wake-up event
[1] HVSON8 package die supply ground is connected to both the GND pin and the exposed center pad. The
GND pin must be soldered to board ground. For enhanced thermal and electrical performance, it is
recommended that the exposed center pad also be soldered to board ground.
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
4 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
7. Functional description
The TJA1021 is the interface between the LIN master/slave protocol controller and the
physical bus in a Local Interconnect Network (LIN). The TJA1021 is LIN 2.1/SAE J2602
compliant and provides optimum ElectroMagnetic Compatibility (EMC) performance due
to wave shaping of the LIN output.
The TJA1021T/20 and TJA1021TK/20 are optimized for the maximum specified LIN
transmission speed of 20 kBd; theTJA1021T/10 and TJA1021TK/10 are optimized for the
LIN transmission speed of 10.4 kBd as specified by the SAE J2602.
7.1 Operating modes
The TJA1021 supports modes for normal operation (Normal mode), power-up (Power-on
mode) and very-low-power operation (Sleep mode). An intermediate wake-up mode
between Sleep and Normal modes is also supported (Standby mode). Figure 3 shows the
state diagram.
Power-on
t
> t
(SLP_N = 1)
gotonorm
INH: high
TERM. = 30 kΩ
RXD: floating
TXD: weak pull-down
Transmitter: off
Normal
INH: high
TERM. = 30 kΩ
RXD: receive data output
TXD: transmit data input
Transmitter: on
switching on V
BAT
t
> t
gotonorm
(SLP_N = 1)
t
> t
gotonorm
(SLP_N = 1)
t
> t
gotosleep
(SLP_N = 0)
Standby
INH: high
TERM. = 30 kΩ
RXD: low
Sleep
INH: floating
TERM. = high ohmic
RXD: floating
TXD: weak pull-down
Transmitter: off
TXD: wake source output
Transmitter: off
t
> t
WAKE_N
(WAKE_N = 0; after 1→0)
or t
> t
(LIN = 0→1; after LIN = 0)
BUS
001aae073
TERM.: slave termination resistor, connected between pins LIN and VBAT
.
Fig 3. State diagram
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
5 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
Table 4.
Mode
Operating modes
SLP_N TXD (output)
RXD
INH
Transmitter Remarks
Sleep mode
0
weak pull-down
floating
floating off
no wake-up request
detected
Standby[1]
mode
0
weak pull-down if
remote wake-up;
strong pull-down if
local wake-up[2]
LOW[3]
HIGH
off
wake-up request
detected; in this mode
the microcontroller
can read the wake-up
source: remote or
local wake-up
[2][3][4]
Normal mode
1
HIGH: recessive state HIGH: recessive state HIGH
LOW: dominant state LOW: dominant state
Normal mode
off
[5]
Power-on mode 0
weak pull-down
floating
HIGH
[1] Standby mode is entered automatically upon any local or remote wake-up event during Sleep mode. Pin INH and the 30 k termination
resistor at pin LIN are switched on.
[2] The internal wake-up source flag (set if a local wake-up did occur and fed to pin TXD) will be reset after a positive edge on pin SLP_N.
[3] The wake-up interrupt (on pin RXD) is released after a positive edge on pin SLP_N.
[4] Normal mode is entered after a positive edge on SLP_N. As long as TXD is LOW, the transmitter is off. In the event of a short-circuit to
ground on pin TXD, the transmitter will be disabled.
[5] Power-on mode is entered after switching on VBAT
.
7.2 Sleep mode
This mode is the most power-saving mode of the TJA1021. Despite its extreme low
current consumption, the TJA1021 can still be woken up remotely via pin LIN, or woken
up locally via pin WAKE_N, or activated directly via pin SLP_N. Filters at the inputs of the
receiver (LIN), of pin WAKE_N and of pin SLP_N prevent unwanted wake-up events due
to automotive transients or EMI. All wake-up events must be maintained for a certain time
period (twake(dom)LIN, twake(dom)WAKE_N and tgotonorm).
Sleep mode is initiated by a falling edge on pin SLP_N in Normal mode. To enter Sleep
mode successfully (INH becomes floating), the sleep command (pin SLP_N = LOW) must
be maintained for at least tgotosleep
.
In Sleep mode the internal slave termination between pins LIN and VBAT is disabled to
minimize the power dissipation in the event that pin LIN is short-circuited to ground. Only
a weak pull-up between pins LIN and VBAT is present.
Sleep mode can be activated independently from the actual level on pin LIN, pin TXD or
pin WAKE_N. This guarantees that the lowest power consumption is achievable even in
case of a continuous dominant level on pin LIN or a continuous LOW on pin WAKE_N.
When VBAT drops below the power-on-reset threshold Vth(POR)L, the TJA1021 enters
Sleep mode.
7.3 Standby mode
Standby mode is entered automatically whenever a local or remote wake-up occurs while
the TJA1021 is in Sleep mode. These wake-up events activate pin INH and enable the
slave termination resistor at the pin LIN. As a result of the HIGH condition on pin INH the
voltage regulator and the microcontroller can be activated.
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
6 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
Standby mode is signalled by a LOW-level on pin RXD which can be used as an interrupt
for the microcontroller.
In Standby mode (pin SLP_N is still LOW), the condition of pin TXD (weak pull-down or
strong pull-down) indicates the wake-up source: weak pull-down for a remote wake-up
request and strong pull-down for a local wake-up request.
Setting pin SLP_N HIGH during Standby mode results in the following events:
• An immediate reset of the wake-up source flag; thus releasing the possible strong
pull-down at pin TXD before the actual mode change (after tgotonorm) is performed
• A change into Normal mode if the HIGH level on pin SLP_N has been maintained for
a certain time period (tgotonorm
)
• An immediate reset of the wake-up request signal on pin RXD
7.4 Normal mode
In Normal mode the TJA1021 is able to transmit and receive data via the LIN bus line. The
receiver detects the data stream at the LIN bus input pin and transfers it via pin RXD to
the microcontroller (see Figure 1): HIGH at a recessive level and LOW at a dominant level
on the bus. The receiver has a supply-voltage related threshold with hysteresis and an
integrated filter to suppress bus line noise. The transmit data stream of the protocol
controller at the TXD input is converted by the transmitter into a bus signal with optimized
slew rate and wave shaping to minimize EME. The LIN bus output pin is pulled HIGH via
an internal slave termination resistor. For a master application an external resistor in
series with a diode should be connected between pin INH or VBAT on one side and pin LIN
on the other side (see Figure 7).
When in Sleep, Standby or Power-up mode, the TJA1021 enters Normal mode whenever
a HIGH level on pin SLP_N is maintained for a time of at least tgotonorm
.
The TJA1021 switches to Sleep mode in case of a LOW-level on pin SLP_N, maintained
for a time of at least tgotosleep
.
7.5 Wake-up
When VBAT exceeds the power-on-reset threshold voltage Vth(POR)H, the TJA1021 enters
Power-on mode. Though the TJA1021 is powered-up and INH is HIGH, both the
transmitter and receiver are still inactive. If SLP_N = 1 for t > tgotonorm, the TJA1021 enters
Normal mode.
There are three ways to wake-up a TJA1021 which is in Sleep mode:
1. Remote wake-up via a dominant bus state of at least twake(dom)LIN
2. Local wake-up via a negative edge at pin WAKE_N
3. Mode change (pin SLP_N is HIGH) from Sleep mode to Normal mode
7.6 Remote and local wake-up
A falling edge at pin LIN followed by a LOW level maintained for a certain time period
(twake(dom)LIN) and a rising edge at pin LIN respectively (see Figure 4) results in a remote
wake-up. It should be noted that the time period twake(dom)LIN is measured either in Normal
mode while TXD is HIGH, or in Sleep mode irrespective of the status of pin TXD.
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
7 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
A falling edge at pin WAKE_N followed by a LOW level maintained for a certain time
period (twake(dom)WAKE_N) results in a local wake-up. The pin WAKE_N provides an internal
pull-up towards pin VBAT. In order to prevent EMI issues, it is recommended to connect an
unused pin WAKE_N to pin VBAT
.
After a local or remote wake-up, pin INH is activated (it goes HIGH) and the internal slave
termination resistor is switched on. The wake-up request is indicated by a LOW active
wake-up request signal on pin RXD to interrupt the microcontroller.
7.7 Wake-up via mode transition
It is also possible to set pin INH HIGH with a mode transition towards Normal mode via pin
SLP_N. This is useful for applications with a continuously powered microcontroller.
7.8 Wake-up source recognition
The TJA1021 can distinguish between a local wake-up request on pin WAKE_N and a
remote wake-up request via a dominant bus state. 'A local wake-up request sets the
wake-up source flag. The wake-up source can be read on pin TXD in the Standby mode. If
an external pull-up resistor on pin TXD to the power supply voltage of the microcontroller
has been added, a HIGH level indicates a remote wake-up request (weak pull-down at pin
TXD) and a LOW level indicates a local wake-up request (strong pull-down at pin TXD;
much stronger than the external pull-up resistor).
The wake-up request flag (signalled on pin RXD) as well as the wake-up source flag
(signalled on pin TXD) are reset immediately after the microcontroller sets pin SLP_N
HIGH.
7.9 TXD dominant time-out function
A TXD dominant time-out timer circuit prevents the bus line from being driven to a
permanent dominant state (blocking all network communication) if pin TXD is forced
permanently LOW by a hardware and/or software application failure. The timer is
triggered by a negative edge on pin TXD. If the duration of the LOW-level on pin TXD
exceeds the internal timer value (tto(dom)TXD), the transmitter is disabled, driving the bus
line into a recessive state. The timer is reset by a positive edge on pin TXD.
7.10 Fail-safe features
Pin TXD provides a pull-down to GND in order to force a predefined level on input pin TXD
in case the pin TXD is unsupplied.
Pin SLP_N provides a pull-down to GND in order to force the transceiver into Sleep mode
in case the pin SLP_N is unsupplied.
Pin RXD is set floating in case of lost power supply on pin VBAT
.
The current of the transmitter output stage is limited in order to protect the transmitter
against short circuit to pins VBAT or GND.
A loss of power (pins VBAT and GND) has no impact on the bus line and the
microcontroller. There are no reverse currents from the bus. The LIN transceiver can be
disconnected from the power supply without influencing the LIN bus.
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
8 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
The output driver at pin LIN is protected against overtemperature conditions. If the
junction temperature exceeds the shutdown junction temperature Tj(sd), the thermal
protection circuit disables the output driver. The driver is enabled again when the junction
temperature has dropped below Tj(sd) and a recessive level is present at pin TXD.
If VBAT drops below Vth(VBATL)L, a protection circuit disables the output driver. The driver is
enabled again when VBAT > Vth(VBATL)H and a recessive level is present at pin TXD.
LIN recessive
V
BAT
0.6V
BAT
V
0.4V
t
dom(LIN)
LIN
BAT
LIN dominant
ground
sleep mode
standby mode
001aae071
Fig 4. Remote wake-up behavior
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
9 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
8. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages are referenced to pin GND; unless
otherwise specified. Positive currents flow into the IC.
Symbol
VBAT
Parameter
Conditions
Min
0.3
0.3
0.3
0.3
0.3
0.3
0.3
40
Max
+40
+6
Unit
V
battery supply voltage
voltage on pin TXD
with respect to GND
ITXD no limitation
VTXD
V
ITXD < 500 A
+7
V
VRXD
voltage on pin RXD
IRXD no limitation
+6
V
IRXD < 500 A
+7
V
VSLP_N
voltage on pin SLP_N
ISLP_N no limitation
ISLP_N < 500 A
+6
V
+7
V
VLIN
voltage on pin LIN
with respect to GND, VBAT and VWAKE_N
+40
+40
-
V
VWAKE_N
IWAKE_N
voltage on pin WAKE_N
current on pin WAKE_N
0.3
15
V
only relevant if VWAKE_N < VGND 0.3
mA
current will flow into pin GND
VINH
voltage on pin INH
0.3
50
VBAT +0.3
+15
V
IO(INH)
VESD
output current on pin INH
electrostatic discharge voltage
mA
[1]
[2]
[2]
according to IEC 61000-4-2 on pins WAKE_N, LIN and VBAT
6
+6
kV
kV
kV
V
human body model
on pins WAKE_N, LIN, VBAT and INH
8
+8
on pins RXD, SLP_N and TXD
2
+2
charge device model
machine model
all pins
all pins
750
200
40
55
+750
+200
+150
+150
[3]
[4]
V
Tvj
virtual junction temperature
storage temperature
C
C
Tstg
[1] Equivalent to discharging a 150 pF capacitor through a 330 resistor; verified by an external test house.
[2] Equivalent to discharging a 100 pF capacitor through a 1.5 k resistor.
[3] Equivalent to discharging a 200 pF capacitor through a 10 resistor and a 0.75 H coil.
[4] Junction temperature in accordance with IEC 60747-1. An alternative definition is: Tj = Tamb + P Rth(j-a), where Rth(j-a) is a fixed value.
The rating for Tvj limits the allowable combinations of power dissipation (P) and ambient temperature (Tamb).
9. Thermal characteristics
Table 6.
Thermal characteristics
According to IEC 60747-1.
Symbol
Parameter
Conditions
Typ
145
50
Unit
K/W
K/W
Rth(j-a)
thermal resistance from junction to ambient
SO8 package; in free air
HVSON8 package; in free air
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
10 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
10. Static characteristics
Table 7.
BAT = 5.5 V to 27 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are defined with respect to ground; positive
currents flow into the IC; typical values are given at VBAT = 12 V; unless otherwise specified.[1]
Static characteristics
V
Symbol
Supply
IBAT
Parameter
Conditions
Min
Typ
Max
Unit
battery supply current
Sleep mode
2
7
10
A
VLIN = VBAT; VWAKE_N = VBAT
V
TXD = 0 V; VSLP_N = 0 V
Standby mode; bus recessive
VINH = VBAT; VLIN = VBAT
150
300
300
1
450
800
800
2
1000
1200
1600
4
A
A
A
mA
V
V
WAKE_N = VBAT; VTXD = 0 V
SLP_N = 0 V
Standby mode; bus dominant
BAT = 12 V; VINH = 12 V
V
VLIN = 0 V; VWAKE_N = 12 V
VTXD = 0 V VSLP_N = 0 V
Normal mode; bus recessive
VINH = VBAT; VLIN = VBAT
VWAKE_N = VBAT; VTXD = 5 V
VSLP_N = 5 V
Normal mode; bus dominant
VBAT = 12 V; VINH = 12 V
VWAKE_N = 12 V; VTXD = 0 V
VSLP_N = 5 V
Power-on reset
Vth(POR)L
LOW-level power-on reset
threshold voltage
power-on reset
1.6
3.1
3.4
0.3
4.4
4.7
0.3
3.9
4.3
1
V
V
V
V
V
V
Vth(POR)H
Vhys(POR)
Vth(VBATL)L
Vth(VBATL)H
Vhys(VBATL)
HIGH-level power-on reset
threshold voltage
2.3
power-on reset hysteresis
voltage
0.05
3.9
LOW-level VBAT LOW
threshold voltage
4.7
4.9
1
HIGH-level VBAT LOW
threshold voltage
4.2
VBAT LOW hysteresis
voltage
0.05
Pin TXD
VIH
HIGH-level input voltage
LOW-level input voltage
hysteresis voltage
2
-
7
V
VIL
0.3
50
-
+0.8
400
1200
V
Vhys
200
500
mV
k
RPD(TXD)
pull-down resistance on pin VTXD = 5 V
TXD
140
IIL
LOW-level input current
LOW-level output current
VTXD = 0 V
5
-
-
+5
-
A
IOL
local wake-up request
1.5
mA
Standby mode; VWAKE_N = 0 V
VLIN = VBAT; VTXD = 0.4 V
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
11 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
Table 7.
Static characteristics …continued
VBAT = 5.5 V to 27 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are defined with respect to ground; positive
currents flow into the IC; typical values are given at VBAT = 12 V; unless otherwise specified.[1]
Symbol
Pin SLP_N
VIH
Parameter
Conditions
Min
Typ
Max
Unit
HIGH-level input voltage
LOW-level input voltage
hysteresis voltage
2
-
7
V
VIL
0.3
50
-
+0.8
400
1200
V
Vhys
200
500
mV
k
RPD(SLP_N)
pull-down resistance on pin VSLP_N = 5 V
SLP_N
140
IIL
LOW-level input current
VSLP_N = 0 V
5
0
+5
A
Pin RXD (open-drain)
IOL LOW-level output current
Normal mode
1.5
-
-
mA
VLIN = 0 V; VRXD = 0.4 V
ILH
HIGH-level leakage current Normal mode
VLIN = VBAT; VRXD = 5 V
5
0
+5
A
Pin WAKE_N
VIH
HIGH-level input voltage
LOW-level input voltage
LOW-level pull-up current
VBAT 1
0.3
30
-
VBAT + 0.3
VBAT 3.3
1
V
VIL
-
V
Ipu(L)
ILH
VWAKE_N = 0 V
12
A
A
HIGH-level leakage current VWAKE_N = 27 V; VBAT = 27 V
5
0
+5
Pin INH
Rsw(VBAT-INH) switch-on resistance
between pins VBAT and INH modes; IINH = 15 mA
VBAT = 12 V
Standby; Normal and Power-on
-
20
0
50
+5
ILH
HIGH-level leakage current Sleep mode
VINH = 27 V; VBAT = 27 V
5
A
Pin LIN
IBUS_LIM
current limitation for driver
dominant state
VBAT = 18 V; VLIN = 18 V
VTXD = 0 V
40
-
100
mA
Rpu
pull-up resistance
Sleep mode; VSLP_N = 0 V
50
-
160
-
250
1
k
A
IBUS_PAS_rec
receiver recessive input
leakage current
VLIN = 27 V; VBAT = 5.5 V
VTXD = 5 V
IBUS_PAS_dom receiver dominant input
leakage current including
pull-up resistor
Normal mode; VTXD = 5 V
600
-
-
-
A
VLIN = 0 V; VBAT = 12 V
[2]
VSerDiode
voltage drop at the serial
diode
in pull-up path with Rslave
ISerDiode = 10 A
0.4
1.0
V
IBUS_NO_GND loss-of-ground bus current VBAT = 27 V; VLIN = 0 V
IBUS_NO_BAT loss-of-battery bus current VBAT = 0 V; VLIN = 27 V
750
-
-
-
-
+10
A
A
V
-
1
VBUSdom
VBUSrec
receiver dominant state
receiver recessive state
receiver center voltage
-
0.4VBAT
-
0.6VBAT
V
VBUS_CNT
VBUS_CNT
=
0.475VBAT 0.5VBAT 0.525VBAT
V
(VBUSrec + VBUSdom) / 2
VHYS
receiver hysteresis voltage VHYS = VBUSrec VBUSdom
-
-
0.175VBAT
47
V
Rslave
slave resistance
connected between pins LIN and
VBAT; VLIN = 0 V; VBAT = 12 V
20
30
k
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
12 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
Table 7.
Static characteristics …continued
VBAT = 5.5 V to 27 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are defined with respect to ground; positive
currents flow into the IC; typical values are given at VBAT = 12 V; unless otherwise specified.[1]
Symbol
CLIN
Parameter
Conditions
Min
Typ
Max
30
Unit
pF
V
[2]
capacitance on pin LIN
dominant output voltage
-
-
-
-
Vo(dom)
Normal mode; VTXD = 0 V
1.4
VBAT = 7.0 V
Normal mode; VTXD = 0 V
VBAT = 18 V
-
-
2.0
V
Thermal shutdown
Tj(sd) shutdown junction
temperature
[2]
150
175
200
C
[1] All parameters are guaranteed over the virtual junction temperature range by design. Factory testing uses correlated test conditions to
cover the specified temperature and power supply voltage range.
[2] Not tested in production; guaranteed by design.
11. Dynamic characteristics
Table 8.
Dynamic characteristics
VBAT = 5.5 V to 18 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are defined with respect to ground; positive
currents flow into the IC; typical values are given at VBAT = 12 V; see Figure 6; unless otherwise specified.[1]
Symbol
Duty cycles
1
Parameter
Conditions
Min
Typ
Max Unit
[2][3][4][7]
[2][3][4][7]
[2][4][5][7]
[2][4][5][7]
[3][4][7]
duty cycle 1
Vth(rec)(max) = 0.744 VBAT
Vth(dom)(max) = 0.581 VBAT
tbit = 50 s; VBAT = 7 V to 18 V
0.396 -
0.396 -
-
V
th(rec)(max) = 0.76 VBAT
-
Vth(dom)(max) = 0.593 VBAT
tbit = 50 s; VBAT = 5.5 V to 7.0 V
2
3
4
duty cycle 2
duty cycle 3
duty cycle 4
V
th(rec)(min) = 0.422 VBAT
-
-
-
-
0.581
0.581
-
Vth(dom)(min) = 0.284 VBAT
tbit = 50 s; VBAT = 7.6 V to 18 V
Vth(rec)(min) = 0.41 VBAT
Vth(dom)(min) = 0.275 VBAT
tbit = 50 s; VBAT = 6.1 V to 7.6 V
V
V
th(rec)(max) = 0.778 VBAT
th(dom)(max) = 0.616 VBAT
0.417 -
0.417 -
tbit = 96 s; VBAT = 7 V to 18 V
th(rec)(max) = 0.797 VBAT
Vth(dom)(max) = 0.630 VBAT
bit = 96 s; VBAT = 5.5 V to 7 V
[3][4][7]
V
-
t
[4][5][7]
Vth(rec)(min) = 0.389 VBAT
Vth(dom)(min) = 0.251 VBAT
tbit = 96 s; VBAT = 7.6 V to 18 V
-
-
-
-
0.590
0.590
[4][5][7]
V
th(rec)(min) = 0.378 VBAT
Vth(dom)(min) = 0.242 VBAT
tbit = 96 s; VBAT = 6.1 V to 7.6 V
Timing characteristics
[2][4]
tf
fall time
-
-
22.5 s
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
13 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
Table 8.
Dynamic characteristics …continued
VBAT = 5.5 V to 18 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are defined with respect to ground; positive
currents flow into the IC; typical values are given at VBAT = 12 V; see Figure 6; unless otherwise specified.[1]
Symbol
tr
Parameter
Conditions
Min
-
Typ
Max Unit
[2][4]
[2][4]
rise time
-
-
22.5 s
t(r-f)
difference between rise VBAT = 7.3 V
and fall time
5
+5
s
[2]
ttx_pd
transmitter propagation rising and falling
delay
-
-
6
s
ttx_sym
transmitter propagation
delay symmetry
2.5
-
-
+2.5 s
[6]
[6]
trx_pd
receiver propagation
delay
rising and falling
Sleep mode
-
6
s
s
s
s
s
trx_sym
twake(dom)LIN
receiver propagation
delay symmetry
2
30
7
-
+2
150
50
10
LIN dominant wake-up
time
80
30
5
twake(dom)WAKE_N dominant wake-up time Sleep mode
on pin WAKE_N
tgotonorm
go to normal time
time period for mode change from
Sleep, Power-on or Standby mode
into Normal mode
2
tinit(norm)
tgotosleep
tto(dom)TXD
normal mode
initialization time
5
-
20
10
90
s
s
ms
go to sleep time
time period for mode change from
Normal slope mode into Sleep mode
2
5
TXD dominant time-out VTXD = 0 V
time
27
55
[1] All parameters are guaranteed over the virtual junction temperature range by design. Factory testing uses correlated test conditions to
cover the specified temperature and power supply voltage range.
[2] Not applicable for the /10 versions of the TJA1021.
tbusrecmin
-------------------------------
[3] 1 3 =
. Variable tbus(rec)(min) is illustrated in the LIN timing diagram in Figure 6.
2 tbit
[4] Bus load conditions are: CBUS = 1 nF and RBUS = 1 k; CBUS = 6.8 nF and RBUS = 660 ; CBUS = 10 nF and RBUS = 500 .
tbusrecmax
-------------------------------
[5] 2 4 =
. Variable tbus(rec)(max) is illustrated in the LIN timing diagram in Figure 6.
2 tbit
[6] Load condition pin RXD: CRXD = 20 pF and RRXD = 2.4 k.
[7] For VBAT > 18 V the LIN transmitter might be suppressed. If TXD is HIGH then the LIN transmitter output is recessive.
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
14 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
V
BAT
WAKE_N
SLP_N
INH
LIN
100 nF
R
L
TJA1021
TXD
RXD
GND
R
RXD
C
RXD
C
L
001aae069
Fig 5. Timing test circuit for LIN transceiver
t
bit
t
t
bit
bit
V
TXD
t
t
bus(rec)(min)
bus(dom)(max)
V
V
th(rec)(max)
thresholds of
receiving node 1
th(dom)(max)
LIN BUS
signal
V
BAT
V
V
th(rec)(min)
thresholds of
receiving node 2
th(dom)(min)
t
t
bus(rec)(max)
bus(dom)(min)
V
V
RXD
receiving
node 1
t
t
rx_pdr
rx_pdf
RXD
receiving
node 2
t
t
prx_pdf
rx_pdr
015aaa245
Fig 6. Timing diagram LIN transceiver
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
15 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
12. Application information
ECU
LIN BUS
LINE
BATTERY
+5 V/
+3.3 V
only for
master node
V
7
INH
BAT
3
1 kΩ
RXD
WAKE_N
V
8
DD
RX0
TX0
Px.x
1
4
2
TXD
MICRO-
CONTROLLER
TJA1021
SLP_N
LIN
6
GND
5
(1)
001aae070
(1) Master: C = 1 nF; slave: C = 220 pF.
Fig 7. Typical application of the TJA1021
13. Test information
Immunity against automotive transients (malfunction and damage) in accordance with LIN
EMC Test Specification / Version 1.0; August 1, 2004.
The waveforms of the applied transients are according to ISO7637-2: Draft 2002-12, test
pulses 1, 2a, 3a and 3b.
13.1 Quality information
This product has been qualified to the appropriate Automotive Electronics Council (AEC)
standard Q100 or Q101 and is suitable for use in automotive applications.
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
16 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
14. Package outline
SO8: plastic small outline package; 8 leads; body width 3.9 mm
SOT96-1
D
E
A
X
c
y
H
v
M
A
E
Z
5
8
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
4
e
w
M
detail X
b
p
0
2.5
5 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
(1)
(1)
(2)
UNIT
A
A
A
b
c
D
E
e
H
L
L
p
Q
v
w
y
Z
θ
1
2
3
p
E
max.
0.25
0.10
1.45
1.25
0.49
0.36
0.25
0.19
5.0
4.8
4.0
3.8
6.2
5.8
1.0
0.4
0.7
0.6
0.7
0.3
mm
1.27
0.05
1.05
0.041
1.75
0.25
0.01
0.25
0.01
0.25
0.1
8o
0o
0.010 0.057
0.004 0.049
0.019 0.0100 0.20
0.014 0.0075 0.19
0.16
0.15
0.244
0.228
0.039 0.028
0.016 0.024
0.028
0.012
inches 0.069
0.01 0.004
Notes
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-18
SOT96-1
076E03
MS-012
Fig 8. Package outline SOT96-1 (SO8)
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
17 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
HVSON8: plastic thermal enhanced very thin small outline package; no leads;
8 terminals; body 3 x 3 x 0.85 mm
SOT782-1
X
D
B
A
E
A
A
1
c
detail X
terminal 1
index area
e
1
C
terminal 1
index area
v
C A
C
B
e
b
y
1
y
w
C
1
4
L
K
E
h
8
5
D
h
0
1
2 mm
L
scale
Dimensions
(1)
Unit
A
A
b
c
D
D
h
E
E
e
e
1
K
v
w
y
y
1
1
h
max 1.00 0.05 0.35
mm nom 0.85 0.03 0.30 0.2 3.00 2.40 3.00 1.60 0.65 1.95 0.30 0.40 0.1 0.05 0.05 0.1
min 0.80 0.00 0.25 2.90 2.35 2.90 1.55 0.25 0.35
3.10 2.45 3.10 1.65
0.35 0.45
Note
1. Plastic or metal protrusions of 0.075 maximum per side are not included.
sot782-1_po
References
Outline
version
European
projection
Issue date
IEC
- - -
JEDEC
JEITA
- - -
09-08-25
09-08-28
SOT782-1
MO-229
Fig 9. Package outline SOT782-1 (HVSON8)
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
18 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
15. Handling information
All input and output pins are protected against ElectroStatic Discharge (ESD) under
normal handling. When handling ensure that the appropriate precautions are taken as
described in JESD625-A or equivalent standards.
16. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
16.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
16.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
• Board specifications, including the board finish, solder masks and vias
• Package footprints, including solder thieves and orientation
• The moisture sensitivity level of the packages
• Package placement
• Inspection and repair
• Lead-free soldering versus SnPb soldering
16.3 Wave soldering
Key characteristics in wave soldering are:
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
19 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
16.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 10) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 9 and 10
Table 9.
SnPb eutectic process (from J-STD-020C)
Package thickness (mm) Package reflow temperature (C)
Volume (mm3)
< 350
350
220
< 2.5
235
220
2.5
220
Table 10. Lead-free process (from J-STD-020C)
Package thickness (mm) Package reflow temperature (C)
Volume (mm3)
< 350
260
350 to 2000
> 2000
260
< 1.6
260
250
245
1.6 to 2.5
> 2.5
260
245
250
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 10.
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
20 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
maximum peak temperature
= MSL limit, damage level
temperature
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 10. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
17. Soldering of HVSON packages
Section 16 contains a brief introduction to the techniques most commonly used to solder
Surface Mounted Devices (SMD). A more detailed discussion on soldering HVSON
leadless package ICs can found in the following application notes:
• AN10365 ‘Surface mount reflow soldering description”
• AN10366 “HVQFN application information”
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
21 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
18. Revision history
Table 11. Revision history
Document ID
TJA1021 v.7
Modifications:
Release date
20110325
Data sheet status
Change notice
Supersedes
Product data sheet
-
TJA1021 v.6
• Section 2.1: features added
• Table 5: parameter deleted - Tamb; conditions changed for VESD
• Table 7, Table 8: parameter names, descriptions and table notes revised
• Figure 6: revised (parameter names corrected)
TJA1021 v.6
TJA1021 v.5
TJA1021 v.4
TJA1021 v.3
TJA1021 v.2
TJA1021 v.1
20101230
20091022
20090119
20071008
20070903
20061016
Product data sheet
Product data sheet
Product data sheet
Product data sheet
Preliminary data sheet
Objective data sheet
-
-
-
-
-
-
TJA1021 v.5
TJA1021 v.4
TJA1021 v.3
TJA1021 v.2
TJA1021 v.1
-
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
22 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
19. Legal information
19.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
suitable for use in medical, military, aircraft, space or life support equipment,
19.2 Definitions
nor in applications where failure or malfunction of an NXP Semiconductors
product can reasonably be expected to result in personal injury, death or
severe property or environmental damage. NXP Semiconductors accepts no
liability for inclusion and/or use of NXP Semiconductors products in such
equipment or applications and therefore such inclusion and/or use is at the
customer’s own risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
19.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Suitability for use in automotive applications — This NXP
Semiconductors product has been qualified for use in automotive
applications. The product is not designed, authorized or warranted to be
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
23 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
19.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
20. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
TJA1021
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 7 — 25 March 2011
24 of 25
TJA1021
NXP Semiconductors
LIN 2.1/SAE J2602 transceiver
21. Contents
1
General description. . . . . . . . . . . . . . . . . . . . . . 1
21
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Low power management . . . . . . . . . . . . . . . . . 1
Protection mechanisms . . . . . . . . . . . . . . . . . . 2
2.1
2.2
2.3
3
4
5
Quick reference data . . . . . . . . . . . . . . . . . . . . . 2
Ordering information. . . . . . . . . . . . . . . . . . . . . 2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3
6
6.1
6.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 4
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
7
Functional description . . . . . . . . . . . . . . . . . . . 5
Operating modes . . . . . . . . . . . . . . . . . . . . . . . 5
Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Standby mode. . . . . . . . . . . . . . . . . . . . . . . . . . 6
Normal mode . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Wake-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Remote and local wake-up. . . . . . . . . . . . . . . . 7
Wake-up via mode transition . . . . . . . . . . . . . . 8
Wake-up source recognition. . . . . . . . . . . . . . . 8
TXD dominant time-out function. . . . . . . . . . . . 8
Fail-safe features . . . . . . . . . . . . . . . . . . . . . . . 8
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
8
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 10
Thermal characteristics . . . . . . . . . . . . . . . . . 10
Static characteristics. . . . . . . . . . . . . . . . . . . . 11
Dynamic characteristics . . . . . . . . . . . . . . . . . 13
Application information. . . . . . . . . . . . . . . . . . 16
Test information. . . . . . . . . . . . . . . . . . . . . . . . 16
Quality information . . . . . . . . . . . . . . . . . . . . . 16
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 17
Handling information. . . . . . . . . . . . . . . . . . . . 19
9
10
11
12
13
13.1
14
15
16
Soldering of SMD packages . . . . . . . . . . . . . . 19
Introduction to soldering . . . . . . . . . . . . . . . . . 19
Wave and reflow soldering . . . . . . . . . . . . . . . 19
Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . 19
Reflow soldering. . . . . . . . . . . . . . . . . . . . . . . 20
16.1
16.2
16.3
16.4
17
18
Soldering of HVSON packages. . . . . . . . . . . . 21
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 22
19
Legal information. . . . . . . . . . . . . . . . . . . . . . . 23
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 23
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 24
19.1
19.2
19.3
19.4
20
Contact information. . . . . . . . . . . . . . . . . . . . . 24
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2011.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 25 March 2011
Document identifier: TJA1021
相关型号:
TJA1021TK/10
IC DATACOM, INTERFACE CIRCUIT, PDSO8, 3 X 3 MM, 0.85 MM HEIGTH, PLASTIC, MO-229, SOT782-1, VSON-8, Network Interface
NXP
TJA1021TK/10/C/S90
LIN 2.1/SAE J2602 transceiver, SOT782-1 Package, Standard Marking, Reel Pack, SMD, 13"
NXP
©2020 ICPDF网 联系我们和版权申明