MC9328MX21SCVM [NXP]
DB I.MX21 17X17 PB-FR;型号: | MC9328MX21SCVM |
厂家: | NXP |
描述: | DB I.MX21 17X17 PB-FR 时钟 外围集成电路 |
文件: | 总88页 (文件大小:905K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Document Number: MC9328MX21S
Rev. 1.3, 06/2008
Freescale Semiconductor
Data Sheet: Technical Data
MC9328MX21S
Package Information
(MAPBGA–289)
MC9328MX21S
266 MHz
Ordering Information: See Table 1 on page 3
Contents
1 Introduction
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . .4
3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4 Pin Assignment and Package Information . . .84
5 Document Revision History . . . . . . . . . . . . . . .87
Freescale’s i.MX family of microprocessors has
demonstrated leadership in the portable handheld
market. Building on the success of the MX (Media
Extensions) series, the i.MX21S (MC9328MX21S)
provides a leap in performance with an ARM926EJ-S
microprocessor core that provides accelerated Java
™
supportinaddition tohighlyintegrated systemfunctions.
The i.MX21S device addresses the needs of multiple
markets with intelligent integrated peripherals, advanced
®
ARM processor core, and power management
capabilities.
The i.MX21S features the advanced and power-efficient
ARM926EJ-S core operating at speeds up to 266 MHz
and is part of a growing family of Smart Speed products
that offer high performance processing optimized for
lowest power consumption. On-chip modules such as an
®
LCD controller, USB On-The-Go, 1-Wire interface,
and synchronous serial interfaces offer designers a rich
suite of peripherals that can enhance many products.
For cost sensitive applications, the NAND Flash
controller allows the use of low-cost NAND Flash
This document contains information on a new product. Specifications and information herein are subject to change
without notice.
© Freescale Semiconductor, Inc., 2005–2008. All rights reserved.
Introduction
devices to be used as primary or secondary non-volatile storage. The on-chip error correction code (ECC)
and parity checking circuitry of the NAND Flash controller frees the CPU for other tasks. WLAN,
Bluetooth and expansion options are provided through PCMCIA/CF, USB, and MMC/SD host controllers.
The device is packaged in a 289-pin MAPBGA.
System Control
Connectivity
®
CSPI x 2
SSI x 2
i.MX21S
JTAG/Multi-ICE
System Boot
ARM9 Platform
2
I C
Clock Management
MAX
ARM926EJ-S
Audio Mux
UART 1, 3, & 4
1-Wire
MMU
I Cache
D Cache
Standard System I/O
Timers x 3
Bus Control
Memory Control
FIRI
Internal Control
USB OTG/ 1 Host
PWM
WDOG
RTC
Memory Expansion
Memory Interface
Human Interface
SDRAMC
WEIM
LCD Controller
SLCD Controller
Keypad
GPIO
DMAC
MMC/SD x 2
PCMCIA/CF
NFC
Figure 1. i.MX21S Functional Block Diagram
1.1
Conventions
This document uses the following conventions:
•
•
•
•
•
•
•
•
OVERBAR is used to indicate a signal that is active when pulled low: for example, RESET.
Logic level one is a voltage that corresponds to Boolean true (1) state.
Logic level zero is a voltage that corresponds to Boolean false (0) state.
To set a bit or bits means to establish logic level one.
To clear a bit or bits means to establish logic level zero.
A signal is an electronic construct whose state conveys or changes in state convey information.
A pin is an external physical connection. The same pin can be used to connect a number of signals.
Asserted means that a discrete signal is in active logic state.
— Active low signals change from logic level one to logic level zero.
— Active high signals change from logic level zero to logic level one.
Negated means that an asserted discrete signal changes logic state.
— Active low signals change from logic level zero to logic level one.
— Active high signals change from logic level one to logic level zero.
•
MC9328MX21S Technical Data, Rev. 1.3
2
Freescale Semiconductor
Introduction
•
•
LSB means least significant bit or bits, and MSB means most significant bit or bits. References to low and
high bytes or words are spelled out.
Numbers preceded by a percent sign (%) are binary. Numbers preceded by a dollar sign ($) or 0x are
hexadecimal.
1.2
Reference Documentation
The following documents are required for a complete description of the i.MX21S and are necessary to
design properly with the device. Especially for those not familiar with the ARM926EJ-S processor the
following documents are helpful when used in conjunction with this manual.
ARM Architecture Reference Manual (ARM Ltd., order number ARM DDI 0100)
ARM7TDMI Data Sheet (ARM Ltd., order number ARM DDI 0029)
ARM920T Technical Reference Manual (ARM Ltd., order number ARM DDI 0151C)
MC9328MX21S Product Brief (order number MC9328MX21SPB)
The Freescale manuals are available on the Freescale Semiconductor Web site at http://
www.freescale.com. These documents may be downloaded directly from the Freescale Web site, or printed
versions may be ordered. The ARM Ltd. documentation is available from http://www.arm.com.
1.3
Ordering Information
Table 1 provides ordering information for the device.
Table 1. Ordering Information
Part Order Number
Package Size
Package Type
Operating Range
MC9328MX21SVK
289-lead MAPBGA
0.65mm, 14mm x 14mm
Lead-free
0°C–70°C
MC9328MX21SCVK
MC9328MX21SVM
MC9328MX21SCVM
289-lead MAPBGA
0.65mm, 14mm x 14mm
Lead-free
Lead-free
Lead-free
-40°C–85°C
0°C–70°C
289-lead MAPBGA
0.8mm, 17mm x 17mm
289-lead MAPBGA
0.8mm, 17mm x 17mm
-40°C–85°C
1.4
Features
The i.MX21S boasts a robust array of features that can support a wide variety of applications. Below is a
brief description of i.MX21S features.
•
•
ARM926EJ-S Core Complex
Display and Video Modules
— LCD Controller (LCDC)
— Smart LCD Controller (SLCDC)
Wireless Connectivity
•
•
— Fast Infra-Red Interface (FIRI)
Wired Connectivity
— USB On-The-Go (USBOTG) Controller
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
3
Signal Descriptions
— Three Universal Asynchronous Receiver/Transmitters (UARTx)
— Two Configurable Serial Peripheral Interfaces (CSPIx) for High Speed Data Transfer
2
— Inter-IC (I C) Bus Module
— Two Synchronous Serial Interfaces (SSI) with Inter-IC Sound (I S)
2
— Digital Audio Mux
— One-Wire Controller
— Keypad Interface
•
•
Memory Expansion and I/O Card Support
— Two Multimedia Card and Secure Digital (MMC/SD) Host Controller Modules
Memory Interface
— External Interface Module (EIM)
— SDRAM Controller (SDRAMC)
— NAND Flash Controller (NFC)
— PCMCIA/CF Interface
•
Standard System Resources
— Clock Generation Module (CGM) and Power Control Module
— Three General-Purpose 32-Bit Counters/Timers
— Watchdog Timer
— Real-Time Clock/Sampling Timer (RTC)
— Pulse-Width Modulator (PWM) Module
— Direct Memory Access Controller (DMAC)
— General-Purpose I/O (GPIO) Ports
— Debug Capability
2 Signal Descriptions
Table 2 identifies and describes the i.MX21S signals. Pin assignment is provided in Section 4, “Pin
Assignment and Package Information” and in the “Signal Multiplexing Scheme” table within the reference
manual.
The connections of the pins in Table 2 depends solely upon the user application, however there are a few
factory test signals that are not used in a normal application. Following is a list of these signals and how
they are to be terminated for proper operation of the i.MX21S processor:
•
•
•
•
•
CLKMODE[1:0]: To ensure proper operation, leave these signals as no connects.
OSC26M_TEST: To ensure proper operation, leave this signal as no connect.
EXT_48M: To ensure proper operation, connect this signal to ground.
EXT_266M: To ensure proper operation, connect this signal to ground.
TEST_WB[2:0]: These signals are also multiplexed with GPIO PORT E as well as alternate
keypad signals. If not utilizing these signals for GPIO functionality or for their other multiplexed
function, then configure as GPIO input with pull up enabled, and leave as a no connect.
•
TEST_WB[4:3]: To ensure proper operation, leave these signals as no connects.
MC9328MX21S Technical Data, Rev. 1.3
4
Freescale Semiconductor
Signal Descriptions
Table 2. i.MX21S Signal Descriptions
Signal Name
Function/Notes
External Bus/Chip Select (EIM)
A [25:0]
D [31:0]
EB0
Address bus signals
Data bus signals
MSB Byte Strobe—Active low external enable byte signal that controls D [31:24], shared with SDRAM
DQM0.
EB1
EB2
Byte Strobe—Active low external enable byte signal that controls D [23:16], shared with SDRAM DQM1.
Byte Strobe—Active low external enable byte signal that controls D [15:8], shared with SDRAM DQM2
and PCMCIA PC_REG.
EB3
LSB Byte Strobe—Active low external enable byte signal that controls D [7:0], shared with SDRAM
DQM3 and PCMCIA PC_IORD.
OE
Memory Output Enable—Active low output enables external data bus, shared with PCMCIA PC_IOWR.
CS [5:0]
Chip Select—The chip select signals CS [3:2] are multiplexed with CSD [1:0] and are selected by the
Function Multiplexing Control Register (FMCR) in the System Control chapter. By default CSD [1:0] is
selected. DTACK is multiplexed with CS4.
ECB
LBA
Active low input signal sent by flash device to the EIM whenever the flash device must terminate an on-
going burst sequence and initiate a new (long first access) burst sequence.
Active low signal sent by flash device causing the external burst device to latch the starting burst
address.
BCLK
RW
Clock signal sent to external synchronous memories (such as burst flash) during burst mode.
RW signal—Indicates whether external access is a read (high) or write (low) cycle. This signal is also
shared with the PCMCIA PC_WE.
DTACK
DTACK signal—External input data acknowledge signal, multiplexed with CS4.
Bootstrap
BOOT [3:0]
System Boot Mode Select—The operational system boot mode upon system reset is determined by the
settings of these pins. To hardwire these inputs low, terminate with a 1 KΩ resister to ground. For a logic
high, terminate with a 1 KΩ resistor to VDDA. Do not change the state of these inputs after power-up.
Boot 3 should always be tied to logic low.
SDRAM Controller
SDBA [4:0]
SDIBA [3:0]
SDRAM non-interleave mode bank address signals. These signals are multiplexed with address signals
A[20:16].
SDRAM interleave addressing mode bank address signals. These signals are multiplexed with address
signals A[24:21].
MA [11:0]
DQM [3:0]
SDRAM address signals. MA[9:0] are multiplexed with address signals A[10:1].
SDRAM data qualifier mask multiplexed with EB[3:0]. DQM3 corresponds to D[31:24], DQM2
corresponds to D[23:16], DQM1 corresponds to D[15:8], and DQM0 corresponds to D[7:0].
CSD0
CSD1
RAS
SDRAM Chip Select signal. This signal is multiplexed with the CS2 signal. This signal is selectable by
programming the Function Multiplexing Control Register in the System Control chapter.
SDRAM Chip Select signal. This signal is multiplexed with the CS3 signal. This signal is selectable by
programming the Function Multiplexing Control Register in the System Control chapter.
SDRAM Row Address Select signal.
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
5
Signal Descriptions
Signal Name
Table 2. i.MX21S Signal Descriptions (Continued)
Function/Notes
CAS
SDRAM Column Address Select signal
SDWE
SDRAM Write Enable signal
SDRAM Clock Enable 0
SDRAM Clock Enable 1
SDRAM Clock
SDCKE0
SDCKE1
SDCLK
Clocks and Resets
EXTAL26M
Crystal input (26MHz), or a 16 MHz to 32 MHz oscillator (or square-wave) input when the internal
oscillator circuit is shut down. When using an external signal source, feed this input with a square wave
signal switching from GND to VDDA.
XTAL26M
Oscillator output to external crystal. When using an external signal source, float this output.
EXTAL32K
32 kHz or 32.768 kHz crystal input. When using an external signal source, feed this input with a square
wave signal switching from GND to QVDD5.
XTAL32K
CLKO
Oscillator output to external crystal. When using an external signal source, float this output.
Clock Out signal selected from internal clock signals. Please refer to clock controller for internal clock
selection.
EXT_48M
EXT_266M
RESET_IN
This is a special factory test signal. To ensure proper operation, connect this signal to ground.
This is a special factory test signal. To ensure proper operation, connect this signal to ground.
Master Reset—External active low Schmitt trigger input signal. When this signal goes active, all modules
(except the reset module, SDRAMC module, and the clock control module) are reset.
RESET_OUT
POR
Reset Out—Internal active low output signal from the Watchdog Timer module and is asserted from the
following sources: Power-on reset, External reset (RESET_IN), and Watchdog time-out.
Power On Reset—Active low Schmitt trigger input signal. The POR signal is normally generated by an
external RC circuit designed to detect a power-up event.
CLKMODE[1:0]
OSC26M_TEST
TEST_WB[2:0]
These are special factory test signals. To ensure proper operation, leave these signals as no connects.
This is a special factory test signal. To ensure proper operation, leave this signal as a no connect.
These are special factory test signals. However, these signals are also multiplexed with GPIO PORT E
as well as alternate keypad signals. If not using these signals for GPIO functions or for other multiplexed
functions, then configure as GPIO input with pull-up enabled, and leave as a no connect.
TEST_WB[4:3]
WKGD
These are special factory test signals. To ensure proper operation, leave these signals as no connects.
Battery indicator input used to qualify the walk-up process. Also multiplexed with TIN.
JTAG
®
®
For termination recommendations, see the Table “JTAG pinouts” in the Multi-ICE User Guide from ARM Limited.
TRST
TDO
TDI
Test Reset Pin—External active low signal used to asynchronously initialize the JTAG controller.
Serial Output for test instructions and data. Changes on the falling edge of TCK.
Serial Input for test instructions and data. Sampled on the rising edge of TCK.
Test Clock to synchronize test logic and control register access through the JTAG port.
TCK
TMS
Test Mode Select to sequence the JTAG test controller’s state machine. Sampled on the rising edge of
TCK.
JTAG_CTRL
JTAG Controller select signal—JTAG_CTRL is sampled during the rising edge of TRST. Must be pulled
to logic high for proper JTAG interface to debugger. Pulling JTAG_CRTL low is for internal test purposes
only.
MC9328MX21S Technical Data, Rev. 1.3
6
Freescale Semiconductor
Signal Descriptions
Table 2. i.MX21S Signal Descriptions (Continued)
Function/Notes
Signal Name
RTCK
JTAG Return Clock used to enhance stability of JTAG debug interface devices. This signal is multiplexed
with 1-Wire, therefore using 1-Wire renders RTCK unusable and vice versa.
LCD Controller
LD [17:0]
LCD Data Bus—All LCD signals are driven low after reset and when LCD is off. LD[15:0] signals are
multiplexed with SLCDC1_DAT[15:0] from SLCDC1. LD[16] is multiplexed with EXT_DMAGRANT.
FLM_VSYNC
(or simply referred
to as VSYNC)
Frame Sync or Vsync—This signal also serves as the clock signal output for gate
driver (dedicated signal SPS for Sharp panel HR-TFT).
LP_HSYNC (or simply Line Pulse or HSync
referred to as HSYNC)
LSCLK
OE_ACD
CONTRAST
SPL_SPR
PS
Shift Clock.
Alternate Crystal Direction/Output Enable.
This signal is used to control the LCD bias voltage as contrast control.
Sampling start signal for left and right scanning. This signal is multiplexed with the SLCDC1_CLK.
Control signal output for source driver (Sharp panel dedicated signal). This signal is multiplexed with the
SLCDC1_CS.
CLS
REV
Start signal output for gate driver. This signal is invert version of PS (Sharp panel dedicated signal). This
signal is multiplexed with the SLCDC1_RS.
Signal for common electrode driving signal preparation (Sharp panel dedicated signal). This signal is
multiplexed with SLCDC1_D0.
Smart LCD Controller
SLCDC1_CLK
SLCDC1_CS
SLCDC1_RS
SLCDC1_D0
SLCDC Clock output signal. This signal is multiplexed and available at 2 alternate locations. These are
SPL_SPR and SD2_CLK signals of LCDC and SD2, respectively.
SLCDC Chip Select output signal. This signal is multiplexed and available at 2 alternate signal locations.
These are PS and SD2_CMD signals of LCDC and SD2, respectively.
SLCDC Register Select output signal. This signal is multiplexed and available at 2 alternate signal
locations. These are CLS and SD2_D3 signals of LCDC and SD2, respectively.
SLCDC serial data output signal. This signal is multiplexed and available at 2 alternate signal locations.
These are and REV and SD2_D2 signals of LCDC and SD2, respectively. This signal is inactive when a
parallel data interface is used.
SLCDC1_DAT[15:0] SLCDC Data output signals for connection to a parallel SLCD panel interface. These signals are
multiplexed with LD[15:0] while an alternate 8-bit SLCD muxing is available on LD[15:8]. Further
alternate muxing of these signals are available on some of the USB OTG and USBH1 signals.
SLCDC2_CLK
SLCDC2_CS
SLCDC2_RS
SLCDC2_D0
SLCDC Clock input signal for pass through to SLCD device. This signal is multiplexed with SSI3_CLK
signal from SSI3.
SLCDC Chip Select input signal for pass through to SLCD device. This signal is multiplexed with
SSI3_TXD signal from SSI3.
SLCDC Register Select input signal for pass through to SLCD device. This signal is multiplexed with
SSI3_RXD signal from SSI3.
SLCD Data input signal for pass through to SLCD device. This signal is multiplexed with SSI3_FS signal
from SSI3.
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
7
Signal Descriptions
Table 2. i.MX21S Signal Descriptions (Continued)
Function/Notes
Signal Name
External DMA
EXT_DMAREQ
External DMA Request input signal. This signal is multiplexed with CSPI1_RDY.
EXT_DMAGRANT External DMA Grant output signal. This signal is multiplexed with LD[16] of LCDC and CSPI1_SS1 of
CSPI1.
NAND Flash Controller
NF_CLE
NF_CE
NAND Flash Command Latch Enable output signal. Multiplexed with PC_POE of PCMCIA.
NAND Flash Chip Enable output signal. This signal is multiplexed with PC_CE1 of PCMCIA.
NAND Flash Write Protect output signal. This signal is multiplexed with PC_CE2 of PCMCIA.
NAND Flash Address Latch Enable output signal. This signal is multiplexed with PC_OE of PCMCIA.
NAND Flash Read Enable output signal. This signal is multiplexed with PC_RW of PCMCIA.
NAND Flash Write Enable output signal. This signal is multiplexed with and PC_BVD2 of PCMCIA.
NAND Flash Ready Busy input signal. This signal is multiplexed with PC_RST of PCMCIA.
NF_WP
NF_ALE
NF_RE
NF_WE
NF_RB
NF_IO[15:0]
NAND Flash Data input and output signals. NF_IO[15:7] signals are multiplexed with A[25:21] and
A[15:13]. NF_IO[7:0] signals are multiplexed with several PCMCIA signals.
PCMCIA Controller
PC_A[25:0]
PC_D[15:0]
PC_CD1
PCMCIA Address signals. These signals are multiplexed with A[25:0].
PCMCIA Data input and output signals. These signals are multiplexed with D[15:0].
PCMCIA Card Detect1 input signal. This signal is multiplexed with NFIO[7] signal of NF.
PCMCIA Card Detect2 input signal. This signal is multiplexed with NFIO[6] signal of NF.
PCMCIA Wait input signal to extend current access. This signal is multiplexed with NFIO[5] signal of NF.
PCMCIA Ready input signal indicates card is ready for access. Multiplexed with NFIO[4] signal of NF.
PCMCIA Reset output signal. This signal is multiplexed with NFRB signal of NF.
PC_CD2
PC_WAIT
PC_READY
PC_RST
PC_OE
PCMCIA Memory Read Enable output signal asserted during common or attribute memory read cycles.
This signal is multiplexed with NFALE signal of NF.
PC_WE
PCMCIA Memory Write Enable output signal asserted during common or attribute memory cycles. This
signal is shared with RW of the EIM.
PC_VS1
PC_VS2
PCMCIA Voltage Sense1 input signal. This signal is multiplexed with NFIO[2] signal of NF.
PCMCIA Voltage Sense2 input signal. This signal is multiplexed with NFIO[1] signal of NF.
PCMCIA Battery Voltage Detect1 input signal. This signal is multiplexed with NFIO[0] signal of NF.
PCMCIA Battery Voltage Detect2 input signal. This signal is multiplexed with NF_WE signal of NF.
PCMCIA Speaker Out output signal. This signal is multiplexed with PWMO signal.
PCMCIA Register Select output signal. This signal is shared with EB2 of EIM.
PC_BVD1
PC_BVD2
PC_SPKOUT
PC_REG
PC_CE1
PCMCIA Card Enable1 output signal. This signal is multiplexed with NFCE signal of NF.
PCMCIA Card Enable2 output signal. This signal is multiplexed with NFWP signal of NF.
PCMCIA IO Read output signal. This signal is shared with EB3 of EIM.
PC_CE2
PC_IORD
PC_IOWR
PC_WP
PCMCIA IO Write output signal. This signal is shared with OE signal of EIM.
PCMCIA Write Protect input signal. This signal is multiplexed with NFIO[3] signal of NF.
MC9328MX21S Technical Data, Rev. 1.3
8
Freescale Semiconductor
Signal Descriptions
Table 2. i.MX21S Signal Descriptions (Continued)
Function/Notes
Signal Name
PC_POE
PCMCIA Output Enable signal to enable voltage translation buffers and transceivers. This signal is
multiplexed with NFCLE signal of NF.
PC_RW
PCMCIA Read Write output signal to control external transceiver direction. Asserted high for read
access and negated low for write access. This signal is multiplexed with NFRE signal of NF.
PC_PWRON
PCMCIA input signal to indicate that the card power has been applied and stabilized.
CSPI
CSPI1_MOSI
CSPI1_MISO
CSPI1_SS[2:0]
Master Out/Slave In signal
Master In/Slave Out signal
Slave Select (Selectable polarity) signal. CSPI1_SS2 is also multiplexed with USBG_RXDAT and
CSPI1_SS1 is multiplexed with EXT_DMAGRANT.
CSPI1_SCLK
CSPI1_RDY
Serial Clock signal
Serial Data Ready signal. Also multiplexed with EXT_DMAREQ.
Master Out/Slave In signal. This signal is multiplexed with USBH2_TXDP signal of USB OTG.
Master In/Slave Out signal. This signal is multiplexed with USBH2_TXDM signal of USB OTG.
CSPI2_MOSI
CSPI2_MISO
CSPI2_SS[2:0]
Slave Select (Selectable polarity) signals. These signals are multiplexed with USBH2_FS,
USBH2_RXDP and USBH2_RXDM signal of USB OTG
CSPI2_SCLK
TIN
Serial Clock signal. This signal is multiplexed with USBH2_OE signal of USB OTG
General Purpose Timers
Timer Input Capture or Timer Input Clock—The signal on this input is applied to all 3 timers
simultaneously. This signal is muxed with the Walk-up Guard Mode WKGD signal in the PLL, Clock, and
Reset Controller module.
TOUT1
(or simply TOUT)
Timer Output signal from General Purpose Timer1 (GPT1). This signal is multiplexed with SYS_CLK1
and SYS_CLK2 signal of SSI1 and SSI2. The pin name of this signal is simply TOUT.
TOUT2
TOUT3
Timer Output signal from General Purpose Timer1 (GPT2). This signal is multiplexed with PWMO.
Timer Output signal from General Purpose Timer1 (GPT3). This signal is multiplexed with PWMO.
USB On-The-Go
USB_BYP
USB_PWR
USB Bypass input active low signal. This signal can only be used for USB function, not for GPIO.
USB Power output signal
USB_OC
USB Over current input signal. This signal can only be used for USB function, not for GPIO.
USB OTG Receive Data Plus input signal. This signal is muxed with SLCDC1_DAT15.
USB OTG Receive Data Minus input signal. This signal is muxed with SLCDC1_DAT14.
USB OTG Transmit Data Plus output signal. This signal is muxed with SLCDC1_DAT13.
USB OTG Transmit Data Minus output signal. This signal is muxed with SLCDC1_DAT12.
USB OTG Transceiver differential data receive signal. Multiplexed with CSPI1_SS2.
USB OTG Output Enable signal. This signal is muxed with SLCDC1_DAT11.
USB OTG Transceiver ON output signal. This signal is muxed with SLCDC1_DAT9.
USBG_RXDP
USBG_RXDM
USBG_TXDP
USBG_TXDM
USBG_RXDAT
USBG_OE
USBG_ON
USBG_FS
USB OTG Full Speed output signal. This signal is multiplexed with external transceiver USBG_TXR_INT
signal of USB OTG. This signal is muxed with SLCDC1_DAT10.
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
9
Signal Descriptions
Table 2. i.MX21S Signal Descriptions (Continued)
Function/Notes
Signal Name
USBH1_RXDP
USB Host1 Receive Data Plus input signal. This signal is multiplexed with UART4_RXD and
SLCDC1_DAT6. It also provides an alternative multiplex for UART4_RTS, where this signal is selectable
by programming the Function Multiplexing Control Register in the System Control chapter.
USBH1_RXDM
USBH1_TXDP
USB Host1 Receive Data Minus input signal. This signal is muxed with SLCDC1_DAT5. It also provides
an alternative multiplex for UART4_CTS.
USB Host1 Transmit Data Plus output signal. This signal is multiplexed with UART4_CTS and
SLCDC1_DAT4. It also provides an alternative multiplex for UART4_RXD, where this signal is selectable
by programming the Function Multiplexing Control Register in the System Control chapter.
USBH1_TXDM
USBH1_RXDAT
USBH1_OE
USB Host1 Transmit Data Minus output signal. Multiplexed with UART4_TXD and SLCDC1_DAT3.
USB Host1 Transceiver differential data receive signal. Multiplexed with USBH1_FS.
USB Host1 Output Enable signal. This signal is muxed with SLCDC1_DAT2.
USBH1_FS
USB Host1 Full Speed output signal. Multiplexed with UART4_RTS and SLCDC1_DAT1 and
USBH1_RXDAT.
USBH_ON
USBG_SCL
USB Host transceiver ON output signal. This signal is muxed with SLCDC1_DAT0.
2
USB OTG I C Clock input/output signal. This signal is multiplexed with SLCDC1_DAT8.
2
USBG_SDA
USB OTG I C Data input/output signal. This signal is multiplexed with SLCDC1_DAT7.
USBG_TXR_INT
USB OTG transceiver interrupt input. Multiplexed with USBG_FS.
Secure Digital Interface
SD1_CMD
SD Command bidirectional signal—If the system designer does not want to make use of the internal pull-
up, via the Pull-up enable register, a 4.7k–69k external pull-up resistor must be added.
SD1_CLK
SD Output Clock.
SD1_D[3:0]
SD Data bidirectional signals—If the system designer does not want to make use of the internal pull-up,
via the Pull-up enable register, a 50k–69k external pull-up resistor must be added.
SD2_CMD
SD2_CLK
SD2_D[3:0]
SD Command bidirectional signal. This signal is multiplexed with SLCDC1_CS signal from SLCDC1.
SD Output Clock signal. This signal is multiplexed with SLCDC1_CLK signal from SLCDC1.
SD Data bidirectional signals. SD2_D[3:2] are multiplexed with SLCDC1_RS and SLCDC_D0 signals
from SLCDC1.
UARTs – IrDA/Auto-Bauding
(Note: UART2 is not used in the MC9328MX21S)
UART1_RXD
UART1_TXD
UART1_RTS
UART1_CTS
UART3_RXD
UART3_TXD
UART3_RTS
UART3_CTS
UART4_RXD
UART4_TXD
UART4_RTS
Receive Data input signal
Transmit Data output signal
Request to Send input signal
Clear to Send output signal
Receive Data input signal. This signal is multiplexed with IR_RXD from FIRI.
Transmit Data output signal. This signal is multiplexed with IR_TXD from FIRI.
Request to Send input signal
Clear to Send output signal
Receive Data input signal which is multiplexed with USBH1_RXDP and USBH1_TXDP.
Transmit Data output signal which is multiplexed with USBH1_TXDM.
Request to Send input signal which is multiplexed with USBH1_FS and USBH1_RXDP.
MC9328MX21S Technical Data, Rev. 1.3
10
Freescale Semiconductor
Signal Descriptions
Table 2. i.MX21S Signal Descriptions (Continued)
Function/Notes
Signal Name
UART4_CTS
Clear to Send output signal which is multiplexed with USBH1_TXDP and USBH1_RXDM.
2
Serial Audio Port – SSI (configurable to I S protocol and AC97)
SSI1_CLK
SSI1_TXD
SSI1_RXD
SSI1_FS
Serial clock signal which is output in master or input in slave
Transmit serial data
Receive serial data
Frame Sync signal which is output in master and input in slave
SSI1 master clock. Multiplexed with TOUT.
SYS_CLK1
SSI2_CLK
SSI2_TXD
SSI2_RXD
SSI2_FS
Serial clock signal which is output in master or input in slave.
Transmit serial data signal
Receive serial data
Frame Sync signal which is output in master and input in slave.
SSI2 master clock. Multiplexed with TOUT.
SYS_CLK2
SSI3_CLK
SSI3_TXD
SSI3_RXD
SSI3_FS
Serial clock signal which is output in master or input in slave. Multiplexed with SLCDC2_CLK
Transmit serial data signal which is multiplexed with SLCDC2_CS
Receive serial data which is multiplexed with SLCDC2_RS
Frame Sync signal which is output in master and input in slave. Multiplexed with SLCDC2_D0.
Serial clock signal which is output in master or input in slave.
Transmit serial data
SAP_CLK
SAP_TXD
SAP_RXD
SAP_FS
Receive serial data
Frame Sync signal which is output in master and input in slave.
2
I C
2
I2C_CLK
I C Clock
2
I2C_DATA
I C Data
1-Wire
OWIRE
PWMO
1-Wire input and output signal. This signal is multiplexed with JTAG RTCK.
PWM
PWM Output. This signal is multiplexed with PC_SPKOUT of PCMCIA, as well as TOUT2 and TOUT3
of the General Purpose Timer module.
General Purpose Input/Output
PB[10:21], PF[16]
KP_COL[7:0]
Dedicated GPIO. When unused, program this signal as an input with the on-chip pull-up resistor enabled.
Keypad
Keypad Column selection signals. KP_COL[7:6] are multiplexed with UART2_CTS and UART2_TXD
respectively. Alternatively, KP_COL6 is also available on the internal factory test signal TEST_WB2. The
Function Multiplexing Control Register in the System Control chapter must be used in conjunction with
programming the GPIO multiplexing (to select the alternate signal multiplexing) to choose which signal
KP_COL6 is available.
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
11
Specifications
Table 2. i.MX21S Signal Descriptions (Continued)
Function/Notes
Signal Name
KP_ROW[7:0]
Keypad Row selection signals. KP_ROW[7:6] are multiplexed with UART2_RTS and UART2_RXD
signals respectively. Alternatively, KP_ROW7 and KP_ROW6 are available on the internal factory test
signals TEST_WB0 and TEST_WB1 respectively. The Function Multiplexing Control Register in the
System Control chapter must be used in conjunction with programming the GPIO multiplexing (to select
the alternate signal multiplexing) to choose which signals KP_ROW6 and KP_ROW7 are available.
Noisy Supply Pins
NVDD
NVSS
Noisy Supply for the I/O pins. There are six (6) I/O voltages, NVDD1 through NVDD6.
Noisy Ground for the I/O pins
Supply Pins – Analog Modules
VDDA
Supply for analog blocks
QVSS (internally
Quiet GND for analog blocks (QVSS and AVSS are synonymous)
connected to AVSS)
Internal Power Supplies
QVDD
QVSS
Power supply pins for silicon internal circuitry
Quiet GND pins for silicon internal circuitry
QVDDX
Power supply pin for the ARM core. Externally connect directly to QVDD
3 Specifications
This section contains the electrical specifications and timing diagrams for the i.MX21S processor.
3.1
Maximum Ratings
Table 3 provides the maximum ratings.
CAUTION
Stresses beyond those listed under “Maximum Ratings,” (Table 3) may cause
permanent damage to the device. These are stress ratings only. Functional operation
of the device at these or any other conditions beyond those indicated under
“266 MHz Recommended Operating Range” (Table 4) is not implied. Exposure to
maximum-rated conditions for extended periods may affect device reliability.
Table 3. Maximum Ratings
Ref. Num
Parameter
Symbol
QVDDX
Min
Max
Units
1
Supply Voltage
QVDD
-0.3
-0.3
-0.3
-55
2.1
3.3
V
V
V
max,
max
NVDD
VDDA
max
max,
1
2
3
Input Voltage Range
V
VDD + 0.3
150
Imax
o
Storage Temperature Range
T
C
storage
1. VDD is the supply voltage associated with the input. See Signal Multiplexing Scheme table in the reference manual.
MC9328MX21S Technical Data, Rev. 1.3
12
Freescale Semiconductor
Specifications
3.2
Recommended Operating Range
Table 4 provides the recommended operating ranges. The device has multiple pairs of VDD and VSS
power supply and return pins. QVDD, QVDDx, and QVSS pins are used for internal logic. All other VDD
and VSS pins are for the I/O pads voltage supply, and each pair of VDD and VSS provides power to the
enclosed I/O pads. This design allows different peripheral supply voltage levels in a system.
Because VDDA pins are supply voltages to the analog pads, it is recommended to isolate and noise-filter
the VDDA pins from other VDD pins.
For more information about I/O pads grouping per VDD, please refer to Table 4.
Table 4. 266 MHz Recommended Operating Range
Rating
Symbol
Minimum
Maximum
Unit
Operating temperature range
Part No. Suffix
VK/VM
T
0
70
85
°C
°C
V
A
CVK/CVM
T
- 40
1.70
1.45
1.70
A
I/O supply voltage NVDD 1–6
NVDD
3.30
1.65
3.30
x
Internal supply voltage (Core = 266 MHz)
Analog supply voltage
QVDD, QVDDx
VDDA
V
V
3.3
DC Electrical Characteristics
Table 5 contains the DC characteristics of the i.MX21S.
Table 5. DC Characteristics
1
Parameter
Symbol
Test Conditions
Min
Typ
Max
Units
High-level input voltage
V
–
–
0.7NVDD
–
–
–
–
–
NVDD
IH
Low-level Input voltage
V
O
0.8NVDD
–
0.3NVDD
IL
High-level output voltage
Low-level output voltage
High-level output current, slow I/O
V
I
= spec’ed Drive
= spec’ed Drive
–
0.2NVDD
–
V
V
OH
OH
V
I
OL
OL
I
V
=0.8NVDD
mA
OH_S
out
2
DSCR = 000
DSCR = 001
DSCR = 011
DSCR = 111
-2
-4
-8
-12
High-level output current, fast I/O
Low-level output current, slow I/O
I
V
=0.8NVDD1
–
–
–
–
mA
mA
OH_F
out
2
DSCR = 000
DSCR = 001
DSCR = 011
DSCR = 111
-3.5
-4.5
-5.5
-6.5
I
V
=0.2NVDD
OL_S
out
2
DSCR = 000
DSCR = 001
DSCR = 011
DSCR = 111
2
4
8
12
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
13
Specifications
Table 5. DC Characteristics (Continued)
1
Parameter
Symbol
Test Conditions
=0.2NVDD1
DSCR = 000
DSCR = 001
DSCR = 011
DSCR = 111
Min
Typ
Max
Units
Low-level output current, fast I/O
I
V
–
–
mA
OL_F
out
2
3.5
4.5
5.5
6.5
Schmitt trigger Positive–input threshold
Schmitt trigger Negative–input threshold
Hysteresis
V +
–
–
0.75
–
–
–
2.15
V
V
T
V -
–
–
1
T
V
–
0.3
–
V
HYS
Input leakage current (no pull-up or pull-
down)
I
V
= 0 or NVDD
= NVDD or 0
–
μA
in
in
I/O leakage current
I
V
–
–
5
μA
OZ
I/O
I/O = High impedance
state
1. Data labeled Typical is not guaranteed, but is intended as an indication of the IC's potential performance.
2. For DSCR definition refer to the System Control chapter in the reference manual.
Table 6 shows the input and output capacitance for the device.
Table 6. Input/Output Capacitance
Parameter
Input capacitance
Output capacitance
Symbol
Min
Typ
Max
5
Units
pF
C
C
i
–
–
–
–
5
pF
o
Table 7 shows the power consumption for the device.
Table 7. Power Consumption
ID Parameter
Conditions
Symbol
Typ Max Units
1
Run Current QVDD = QVDDX = 1.65 V, NVDD1 = 1.8 V.
NVDD2 through NVDD6 = VDDA = 3.1V.
Core = 266 MHz, System = 133 MHz.
MPEG4 Playback (QVGA) from MMC/SD card, 30fps,
44.1kHz audio.
I
+ I
120
8
–
–
–
mA
mA
mA
QVDD
QVDDX
I
NVDD1
I
through I
+ I
6.6
NVDD2
NVDD6
VDDA
2
Sleep Current Standby current with Well Biasing System enabled.
I
STBY
1
Well Bias Control Register (WBCR) must be set as
follows:
WBCR:
CRM_WBS bits = 01
CRM_WBFA bit = 1
CRM_WBM bits = 001
CRM_SPA_SEL bit = 1
FMCR bit = 1
QVDD = QVDDX = 1.65V, TA
–
–
3.0
700
–
mA
μA
μA
QVDD = QVDDX = 1.65V, 25°
QVDD = QVDDX = 1.55V, 25° 320
For WBCR definition refer to System Control Chapter
in the reference manual.
1. TA = 70°C for suffixes VK, VM, DVK, DVM, and SVK. TA = 85°C for suffixes CVK, CVM, and SCVK.
MC9328MX21S Technical Data, Rev. 1.3
14
Freescale Semiconductor
Specifications
3.4
AC Electrical Characteristics
The AC characteristics consist of output delays, input setup and hold times, and signal skew times. All
signals are specified relative to an appropriate edge of other signals. All timing specifications are specified
at a system operating frequency (HCLK) from 0 MHz to 133 MHz (core operating frequency 266 MHz)
with an operating supply voltage from V
All timing is measured at 30 pF loading with the exception of fast I/O signals as discussed below. Refer
to the reference manual’s System Control Chapter for details on drive strength settings.
to V
under an operating temperature from T to T .
L H
DD max
DD min
Table 8 provides the maximum loading guidelines that can be tolerated on a memory I/O signal (also
known as Fast I/O) to achieve 133 MHz operation. These critical signals include the SDRAM Clock
(SDCLK), Data Bus signals (D[31:0]), lower order address signals such as A0-A10, MA10, MA11, and
other signals required to meet 133 MHz timing.
The values shown in Table 8 apply over the recommended operating temperature range. Care must be
taken to minimize parasitic capacitance of associated printed circuit board traces.
Table 8. Loading Guidelines for Fast IO Signals to Achieve 133 MHz Operation
Drive Strength Setting (DSCR2–DSCR12)
Maximum I/O Loading at 1.8 V
Maximum I/O Loading at 3.0 V
000: 3.5 mA
001: 4.5 mA
011: 5.5 mA
111: 6.5 mA
9 pF
12 pF
15 pF
19 pF
12 pF
16 pF
21 pF
26 pF
Table 9. 32k/26M Oscillator Signal Timing
Parameter
Minimum
RMS
Maximum
Unit
EXTAL32k input jitter (peak to peak) for both System PLL and MCUPLL
EXTAL32k input jitter (peak to peak) for MCUPLL only
EXTAL32k startup time
–
–
5
5
–
20
100
–
ns
ns
800
ms
Table 10. CLKO Rise/Fall Time (at 30pF Loaded)
Best Case Typical Worst Case Units
Rise Time
Fall Time
0.80
0.74
1.00
1.08
1.40
1.67
ns
ns
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
15
Specifications
3.5
DPLL Timing Specifications
Parameters of the DPLL are given in Table 11. In this table, T is a reference clock period after the
ref
predivider and T is the output double clock period.
dck
Table 11. DPLL Specifications
Parameter
Test Conditions
Minimum Typical Maximum
Unit
Reference clock frequency range
Vcc = 1.5V
16
16
–
–
320
32
MHz
MHz
Pre-divider output clock frequency Vcc = 1.5V
range
Double clock frequency range
Pre-divider factor (PD)
Total multiplication factor (MF)
MF integer part
Vcc = 1.5V
220
1
–
–
560
16
MHz
–
–
–
–
–
–
Includes both integer and fractional parts
5
–
15
–
5
–
15
MF numerator
Should be less than the denominator
–
0
–
1022
1023
450
MF denominator
1
–
Frequency lock-in time after
full reset
FOL mode for non-integer MF
(does not include pre-multi lock-in time)
350
400
T
ref
Frequency lock-in time after
partial reset
FOL mode for non-integer MF
(does not include pre-multi lock-in time)
220
480
360
280
530
410
330
580
460
T
ref
Phase lock-in time after
full reset
FPL mode and integer MF
(does not include pre-multi lock-in time)
T
ref
Phase lock-in time after
partial reset
FPL mode and integer MF
(does not include pre-multi lock-in time)
T
ref
Frequency jitter (p-p)
Phase jitter (p-p)
–
–
–
–
0.02
1.0
0.03
1.5
–
2•T
dck
Integer MF, FPL mode, Vcc=1.7V
FOL mode, integer MF,
ns
Power dissipation
1.5
mW
f
= 560 MHz, Vcc = 1.5V
(Avg)
dck
MC9328MX21S Technical Data, Rev. 1.3
16
Freescale Semiconductor
Specifications
3.6
Reset Module
The timing relationships of the Reset module with the POR and RESET_IN are shown in Figure 2 and
Figure 3. Be aware that NVDD must ramp up to at least 1.7V for NVDD1 and 2.7V for NVDD2-6 before
QVDD is powered up to prevent forward biasing.
1
POR
Can be adjusted depending on the crystal
start-up time 32kHz or 32.768kHz
2
RESET_POR
Exact 300ms
3
7 cycles @ CLK32
RESET_DRAM
4
14 cycles @ CLK32
HRESET
RESET_OUT
CLK32
HCLK
Figure 2. Timing Relationship with POR
5
RESET_IN
14 cycles @ CLK32
4
HRESET
RESET_OUT
6
CLK32
HCLK
Figure 3. Timing Relationship with RESET_IN
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
17
Specifications
Table 12. Reset Module Timing Parameters
1.8 V 0.10 V 3.0 V 0.30 V
Ref
No.
Parameter
Unit
Min
Max
Min
Max
1
2
Width of input POWER_ON_RESET
800
300
–
800
300
–
ms
ms
Width of internal POWER_ON_RESET
(CLK32 at 32 kHz)
300
300
3
4
7k to 32k-cycle stretcher for SDRAM reset
7
7
7
7
Cycles of CLK32
Cycles of CLK32
14k to 32k-cycle stretcher for internal system reset HRESERT
and output reset at pin RESET_OUT
14
14
14
14
5
6
Width of external hard-reset RESET_IN
4k to 32k-cycle qualifier
4
4
–
4
4
4
–
4
Cycles of CLK32
Cycles of CLK32
3.7
External DMA Request and Grant
The External DMA request is an active low signal to be used by devices external to i.MX21 processor to
request the DMAC for data transfer.
After assertion of External DMA request the DMA burst will start when the channel on which the External
request is the source (as per the RSSR settings) becomes the current highest priority channel. The external
device using the External DMA request should keep its request asserted until it is serviced by the DMAC.
One External DMA request will initiate one DMA burst.
The output External Grant signal from the DMAC is an active-low signal.When the following conditions
are true, the External DMA Grant signal is asserted with the initiation of the DMA burst.
•
The DMA channel for which the DMA burst is ongoing has request source as external DMA Request
(as per source select register setting).
•
•
REN and CEN bit of this channel are set.
External DMA Request is asserted.
After the grant is asserted, the External DMA request will not be sampled until completion of the DMA
burst. As the external request is synchronized, the request synchronization will not be done during this
period. The priority of the external request becomes low for the next consecutive burst, if another DMA
request signal is asserted.
Worst case—that is, the smallest burst (1 byte read/write) timing diagrams are shown in Figure 4 and
Figure 5. Minimum and maximum timings for the External request and External grant signals are present
in Table 13.
Figure 4 shows the minimum time for which the External Grant signal remains asserted when an External
DMA request is de-asserted immediately after sensing grant signal active.
MC9328MX21S Technical Data, Rev. 1.3
18
Freescale Semiconductor
Specifications
Ext_DMAReq
Ext_DMAGrant
tmin_assert
Figure 4. Assertion of DMA External Grant Signal
Figure 5 shows the safe maximum time for which External DMA request can be kept asserted, after
sensing grant signal active such that a new burst is not initiated.
Ext_DMAReq
Ext_DMAGrant
tmax_req_assert
Data read from
External device
tmax_read
Data written to
External device
tmax_write
NOTE: Assuming in worst case the data is read/written from/to External device as per the above waveform.
Figure 5. Safe Maximum Timings for External Request De-Assertion
Table 13. DMA External Request and Grant Timing Parameters
3.0 V
1.8 V
Parameter
Description
Unit
WCS
BCS
WCS
BCS
t
Minimum assertion time of External Grant 8 hclk + 8.6 8 hclk + 2.74 8 hclk + 7.17 8 hclk + 3.25 ns
signal
min_assert
t
Maximum External request assertion time 9 hclk - 20.66 9 hclk - 6.7 9 hclk - 17.96 9 hclk - 8.16
after assertion of Grant signal
ns
ns
ns
max_req_assert
t
Maximum External request assertion time 8 hclk - 6.21 8 hclk - 0.77 8 hclk - 5.84 8 hclk - 0.66
after first read completion
max_read
t
Maximum External request assertion time 3 hclk - 15.87 3 hclk - 8.83 3 hclk - 15.9 3 hclk - 9.12
after completion of first write
max_write
3.8
CSPI Timing Diagrams
To use the internal transmit (TX) and receive (RX) data FIFOs when the CSPI1 module is configured as a
master, two control signals are used for data transfer rate control: the SS signal (output) and the SPI_RDY
signal (input). The SPI 1 Sample Period Control Register (PERIODREG1) and the SPI 2 Sample Period
Control Register (PERIODREG2) can also be programmed to a fixed data transfer rate for either CSPI1
or CSPI2. When the CSPI1 module is configured as a slave, the user can configure the SPI 1 Control
Register (CONTROLREG1) to match the external CSPI master’s timing. In this configuration, SS
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
19
Specifications
becomes an input signal, and is used to latch data into or load data out to the internal data shift registers,
as well as to increment the data FIFO.
2
5
3
SS
1
4
SPIRDY
SCLK, MOSI, MISO
Figure 6. Master CSPI Timing Diagram Using SPI_RDY Edge Trigger
SS
SPIRDY
SCLK, MOSI, MISO
Figure 7. Master CSPI Timing Diagram Using SPI_RDY Level Trigger
SS (output)
SCLK, MOSI, MISO
Figure 8. Master CSPI Timing Diagram Ignore SPI_RDY Level Trigger
SS (input)
SCLK, MOSI, MISO
Figure 9. Slave CSPI Timing Diagram FIFO Advanced by BIT COUNT
SS (input)
6
7
SCLK, MOSI, MISO
Figure 10. Slave CSPI Timing Diagram FIFO Advanced by SS Rising Edge
MC9328MX21S Technical Data, Rev. 1.3
20
Freescale Semiconductor
Specifications
Table 14. Timing Parameters for Figure 6 through Figure 10
Ref No.
Parameter
Minimum
Maximum
Unit
1
1
2
3
4
5
6
7
SPI_RDY to SS output low
SS output low to first SCLK edge
Last SCLK edge to SS output high
SS output high to SPI_RDY low
SS output pulse width
2T
–
–
–
–
–
–
–
ns
ns
ns
ns
ns
ns
ns
2
3·Tsclk
2·Tsclk
0
3
Tsclk + WAIT
SS input low to first SCLK edge
SS input pulse width
T
T
1. T = CSPI system clock period (PERCLK2).
2. Tsclk = Period of SCLK.
3. WAIT = Number of bit clocks (SCLK) or 32.768 kHz clocks per Sample Period Control
Register.
3.9
LCD Controller
This section includes timing diagrams for the LCD controller. For detailed timing diagrams of the LCD
controller with various display configurations, refer to the LCD controller chapter of the i.MX21S
Reference Manual.
T1
LSCLK
LD[17:0]
T2
T3
Figure 11. SCLK to LD Timing Diagram
Table 15. LCDC SCLK Timing Parameters
3.0 0.3V
Symbol
Parameter
Unit
Minimum
Maximum
T1
T2
T3
SCLK period
23
11
11
2000
ns
ns
ns
Pixel data setup time
Pixel data up time
–
–
The pixel clock is equal to LCDC_CLK / (PCD + 1).
When it is in CSTN, TFT or monochrome mode with bus width = 1, SCLK is equal to the pixel clock.
When it is in monochrome with other bus width settings, SCLK is equal to the pixel clock divided by bus width.
The polarity of SCLK and LD can also be programmed.
Maximum frequency of SCLK is HCLK / 3 for TFT and CSTN, otherwise LD output will be incorrect.
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
21
Specifications
Display region
Non-display region
T3
T1
T4
VSYN
T2
HSYN
OE
Line Y
Line 1
Line Y
LD[17:0]
T6
T5
XMAX
T7
HSYN
SCLK
OE
(0,1)
(0,2)
LD[15:0]
(0,X-1)
Figure 12. 4/8/12/16/18 Bit/Pixel TFT Color Mode Panel Timing
Table 16. 4/8/12/16/18 Bit/Pixel TFT Color Mode Panel Timing
Symbol
Description
Minimum
Value
Unit
T1
T2
T3
T4
T5
T6
T7
End of OE to beginning of VSYN
HSYN period
T5+T6+T7-1
(VWAIT1·T2)+T5+T6+T7-1
XMAX+T5+T6+T7
VWIDTH·T2
Ts
Ts
Ts
Ts
Ts
Ts
Ts
–
T2
1
VSYN pulse width
End of VSYN to beginning of OE
HSYN pulse width
(VWAIT2·T2)+1
HWIDTH+1
1
End of HSYN to beginning to OE
End of OE to beginning of HSYN
3
HWAIT2+3
1
HWAIT1+1
Note:
• Ts is the SCLK period.
• VSYN, HSYN and OE can be programmed as active high or active low. In Figure 12, all 3 signals are active low.
• SCLK can be programmed to be deactivated during the VSYN pulse or the OE deasserted period. In Figure 12, SCLK is
always active.
• XMAX is defined in number of pixels in one line.
MC9328MX21S Technical Data, Rev. 1.3
22
Freescale Semiconductor
Specifications
XMAX
SCLK
D1
LD
D2
D320
D320
SPL_SPR
HSYN
T1
T3
T2
T2
T4
T4
CLS
PS
T5
T6
T7
T7
REV
Figure 13. Sharp TFT Panel Timing
Table 17. Sharp TFT Panel Timing
Symbol
Description
Minimum
Value
Unit
T1
T2
T3
T4
T5
T6
T7
SPL/SPR pulse width
–
1
4
3
1
0
1
1
Ts
Ts
Ts
Ts
Ts
Ts
Ts
End of LD of line to beginning of HSYN
End of HSYN to beginning of LD of line
CLS rise delay from end of LD of line
CLS pulse width
HWAIT1+1
HWAIT2 + 4
CLS_RISE_DELAY+1
CLS_HI_WIDTH+1
PS rise delay from CLS negation
REV toggle delay from last LD of line
PS_RISE_DELAY
REV_TOGGLE_DELAY+1
Note:
•
•
•
Falling of SPL/SPR aligns with first LD of line.
Falling of PS aligns with rising edge of CLS.
REV toggles in every HSYN period.
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
23
Specifications
T1
T1
VSYN
T3
T4
T2
T2
XMAX
HSYN
SCLK
Ts
LD[15:0]
Figure 14. Non-TFT Mode Panel Timing
Table 18. Non-TFT Mode Panel Timing
Symbol
Description
Minimum
Value
Unit
T1
T2
T3
T4
HSYN to VSYN delay
HSYN pulse width
VSYN to SCLK
2
1
–
1
HWAIT2+2
HWIDTH+1
0 ≤ T3 ≤ Ts
HWAIT1+1
Tpix
Tpix
–
SCLK to HSYN
Tpix
Note:
• Ts is the SCLK period while Tpix is the pixel clock period.
• VSYN, HSYN and SCLK can be programmed as active high or active low. In Figure 59, all these 3 signals are
active high.
• When it is in CSTN mode or monochrome mode with bus width = 1, T3 = Tpix = Ts.
• When it is in monochrome mode with bus width = 2, 4, and 8, T3 = 1, 2 and 4 Tpix respectively.
MC9328MX21S Technical Data, Rev. 1.3
24
Freescale Semiconductor
Specifications
3.10 Smart LCD Controller
T2
T3
T1
LCD_CS
LCD_CLK (LCD_DATA[6])
T4
T5
T7
LSB
SDATA (LCD_DATA[7])
RS
MSB
T6
RS=0 ≥ command data, RS=1≥ display data
SCKPOL = 1, CSPOL = 0
T2
T3
T1
LCD_CS
LCD_CLK (LCD_DATA[6])
T4
T5
T7
LSB
SDATA (LCD_DATA[7])
RS
MSB
T6
RS=0 ≥ command data, RS=1≥ display data
SCKPOL = 0, CSPOL = 0
T2
T3
LCD_CS
T1
LCD_CLK (LCD_DATA[6])
T4
T5
T7
LSB
SDATA (LCD_DATA[7])
RS
MSB
T6
RS=0 ≥ command data, RS=1≥ display data
SCKPOL = 1, CSPOL = 1
T2
T3
LCD_CS
T1
LCD_CLK (LCD_DATA[6])
T4
T5
T7
LSB
SDATA (LCD_DATA[7])
RS
MSB
T6
RS=0 ≥ command data, RS=1≥ display data
SCKPOL = 0, CSPOL = 1
Figure 15. SLCDC Serial Transfer Timing
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
25
Specifications
Table 19. SLCDC Serial Transfer Timing
Symbol
Description
Pixel clock period
Minimum
Maximum
Unit
T1
T2
T3
T4
T4
T6
T7
42
5
962
–
ns
ns
ns
ns
ns
ns
ns
Chip select setup time
Chip select hold time
Data setup time
5
–
5
–
Data hold time
5
–
Register select setup time
Register select hold time
5
–
5
–
LCD_CLK
LCD_RS
LCD_CS
T4
T2
T5
T1
T3
command data
display data
LCD_DATA[15:0]
CSPOL = 0
LCD_CLK
T5
T4
LCD_RS
LCD_CS
T1
T2
T3
command data
display data
LCD_DATA[15:0]
CSPOL = 1
Figure 16. SLCDC Parallel Transfers Timing
Table 20. SLCDC Parallel Transfers Timing
Symbol
Description
Pixel clock period
Minimum
Maximum
Unit
T1
T2
T3
T4
T5
23
5
962
–
ns
ns
ns
ns
ns
Data setup time
Data hold time
5
–
Register select setup time
Register select hold time
5
–
5
–
MC9328MX21S Technical Data, Rev. 1.3
26
Freescale Semiconductor
Specifications
3.11 Multimedia Card/Secure Digital Host Controller
The DMA interface block controls all data routing between the external data bus (DMA access), internal
MMC/SD module data bus, and internal system FIFO access through a dedicated state machine that
monitors the status of FIFO content (empty or full), FIFO address, and byte/block counters for the MMC/
SD module (inner system) and the application (user programming).
3a
1
2
4b
3b
Bus Clock
4a
5b
5a
Valid Data
CMD_DAT Input
Valid Data
7
CMD_DAT Output
Valid Data
Valid Data
6b
6a
Figure 17. Chip-Select Read Cycle Timing Diagram
Table 21. SDHC Bus Timing Parameters
1.8 V 0.1 V
3.0 V 0.3 V
Ref
No.
Parameter
Unit
Min
Max
Min
Max
1
1
CLK frequency at Data transfer Mode (PP) —10/30 cards
0
0
25/5
0
0
25/5
MHz
kHz
ns
2
2
CLK frequency at Identification Mode
400
400
1
3a
3b
4a
4b
5a
5b
6a
6b
7
Clock high time —10/30 cards
6/33
15/75
–
–
10/50
10/50
–
–
1
Clock low time —10/30 cards
–
–
ns
1
3
3
Clock fall time —10/30 cards
10/50 (5.00)
10/50
ns
1
Clock rise time —10/30 cards
–
14/67 (6.67)
–
10/50
ns
3
Input hold time —10/30 cards
5.7/5.7
5.7/5.7
5.7/5.7
5.7/5.7
0
–
–
5/5
5/5
5/5
5/5
0
–
–
ns
3
Input setup time —10/30 cards
ns
3
Output hold time —10/30 cards
–
–
ns
3
Output setup time —10/30 cards
–
–
ns
3
Output delay time
16
14
ns
1. C ≤ 100 pF / 250 pF (10/30 cards)
L
2. C ≤ 250 pF (21 cards)
L
3. C ≤ 25 pF (1 card)
L
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
27
Specifications
3.11.1 Command Response Timing on MMC/SD Bus
The card identification and card operation conditions timing are processed in open-drain mode. The card
response to the host command starts after exactly N clock cycles. For the card address assignment,
ID
SET_RCA is also processed in the open-drain mode. The minimum delay between the host command and
card response is NCR clock cycles as illustrated in Figure 18. The symbols for Figure 18 through
Figure 22 are defined in Table 22.
Table 22. State Signal Parameters for Figure 18 through Figure 22
Card Active
Definition
Host Active
Definition
Symbol
Symbol
Z
High impedance state
Data bits
S
T
Start bit (0)
D
Transmitter bit
(Host = 1, Card = 0)
*
Repetition
P
E
One-cycle pull-up (1)
End bit (1)
CRC
Cyclic redundancy check bits (7 bits)
NID cycles
Host Command
CID/OCR
Content
CMD
CMD
Content
******
CRC
S T
E Z
Z S T
Z Z Z
Identification Timing
N
CR cycles
Host Command
Content CRC
CID/OCR
******
Content
SET_RCA Timing
S T
E Z
Z S T
Z Z Z
Figure 18. Timing Diagrams at Identification Mode
After a card receives its RCA, it switches to data transfer mode. As shown on the first diagram in
Figure 19, SD_CMD lines in this mode are driven with push-pull drivers. The command is followed by a
period of two Z bits (allowing time for direction switching on the bus) and then by P bits pushed up by the
responding card. The other two diagrams show the separating periods N and N .
RC
CC
MC9328MX21S Technical Data, Rev. 1.3
28
Freescale Semiconductor
Specifications
N
CR cycles
******
Host Command
Response
Content CRC
E Z Z Z
CMD
Content
CRC
ST
E Z Z P
P S T
Command response timing (data transfer mode)
NRC cycles
Response
Content
Host Command
CMD
******
Content
CRC
CRC
E Z Z Z
ST
E Z
Z S T
Timing response end to next CMD start (data transfer mode)
NCC cycles
Host Command
Content
Host Command
CMD
******
Content
CRC
CRC
E Z Z Z
ST
E Z
Z S T
Timing of command sequences (all modes)
Figure 19. Timing Diagrams at Data Transfer Mode
Figure 20 shows basic read operation timing. In a read operation, the sequence starts with a single block
read command (which specifies the start address in the argument field). The response is sent on the
SD_CMD lines as usual. Data transmission from the card starts after the access time delay N , beginning
AC
from the last bit of the read command. If the system is in multiple block read mode, the card sends a
continuous flow of data blocks with distance N until the card sees a stop transmission command. The
AC
data stops two clock cycles after the end bit of the stop command.
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
29
Specifications
N
CR cycles
Host Command
Response
Content CRC
E Z
CMD
DAT
Content
CRC
******
******
ST
E Z Z P
P S T
Z****Z
*****
Z Z P
P S DDDD
Read Data
Timing of single block read
NAC cycles
NCR cycles
******
Host Command
Response
Content
CMD
DAT
Content
CRC
CRC
E Z
ST
E Z Z P
P S T
Z****Z
******
*****
Read Data
*****
*****
Read Data
Z Z P
P S DDDD
P
P S DDDD
NAC cycles
N
AC cycles
Timing of multiple block read
N
CR cycles
Host Command
Content CRC
Response
Content
CMD
******
CRC
E Z
ST
E Z Z P
P S T
NST
DAT
*****
*****
DDDD
DDDDE Z Z Z
Timing of stop command
(CMD12, data transfer mode)
Valid Read Data
Figure 20. Timing Diagrams at Data Read
Figure 21 shows the basic write operation timing. As with the read operation, after the card response, the
data transfer starts after N cycles. The data is suffixed with CRC check bits to allow the card to check
WR
for transmission errors. The card sends back the CRC check result as a CC status token on the data line. If
there was a transmission error, the card sends a negative CRC status (101); otherwise, a positive CRC
status (010) is returned. The card expects a continuous flow of data blocks if it is configured to multiple
block mode, with the flow terminated by a stop transmission command.
MC9328MX21S Technical Data, Rev. 1.3
30
Freescale Semiconductor
Specifications
Figure 21. Timing Diagrams at Data Write
The stop transmission command may occur when the card is in different states. Figure 22 shows the
different scenarios on the bus.
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
31
Specifications
Figure 22. Stop Transmission During Different Scenarios
Table 23. Timing Values for Figure 18 through Figure 22
Parameter
Symbol
Minimum
Maximum
Unit
MMC/SD bus clock, CLK (All values are referred to minimum (VIH) and maximum (VIL)
Command response cycle
Identification response cycle
Access time delay cycle
NCR
NID
2
5
2
64
Clock cycles
Clock cycles
Clock cycles
5
NAC
TAAC + NSAC
MC9328MX21S Technical Data, Rev. 1.3
32
Freescale Semiconductor
Specifications
Unit
Table 23. Timing Values for Figure 18 through Figure 22 (Continued)
Parameter
Command read cycle
Symbol
Minimum
Maximum
NRC
NCC
NWR
NST
8
8
2
2
–
–
–
2
Clock cycles
Clock cycles
Clock cycles
Clock cycles
Command-command cycle
Command write cycle
Stop transmission cycle
TAAC: Data read access time -1 defined in CSD register bit[119:112]
NSAC: Data read access time -2 in CLK cycles (NSAC·100) defined in CSD register bit[111:104]
3.11.2 SDIO-IRQ and ReadWait Service Handling
In SDIO, there is a 1-bit or 4-bit interrupt response from the SDIO peripheral card. In 1-bit mode, the
interrupt response is simply that the SD_DAT[1] line is held low. The SD_DAT[1] line is not used as data
in this mode. The memory controller generates an interrupt according to this low and the system interrupt
continues until the source is removed (SD_DAT[1] returns to its high level).
In 4-bit mode, the interrupt is less simple. The interrupt triggers at a particular period called the Interrupt
Period during the data access, and the controller must sample SD_DAT[1] during this short period to
determine the IRQ status of the attached card. The interrupt period only happens at the boundary of each
block (512 bytes).
CMD
Content
CRC
Response
******
S
ST
E Z Z P S
E Z Z Z
Z Z Z
DAT[1]
For 4-bit
Interrupt Period
IRQ
IRQ
Block Data
Block Data
S
E
E
L H
Interrupt Period
DAT[1]
For 1-bit
Figure 23. SDIO IRQ Timing Diagram
ReadWait is another feature in SDIO that allows the user to submit commands during the data transfer. In
this mode, the block temporarily pauses the data transfer operation counter and related status, yet keeps
the clock running, and allows the user to submit commands as normal. After all commands are submitted,
the user can switch back to the data transfer operation and all counter and status values are resumed as
access continues.
CMD
******
CMD52 CRC
******
P S T
E Z Z Z
DAT[1]
For 4-bit
Block Data
Block Data
S
S
E Z Z L H
S
E
E
DAT[2]
For 4-bit
Block Data
Block Data
E Z Z L L L L L L L L L L L L L L L L L L L L L H Z S
Figure 24. SDIO ReadWait Timing Diagram
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
33
Specifications
3.12 External Memory Interface (EMI) Electricals
3.12.1 NAND-Flash Controller (NFC) Interface
Figure 25, Figure 26, Figure 27, and Figure 28 depict the relative timing requirements among different
signals of the NFC at module level, and Table 24 lists the timing parameters. The NAND Flash Controller
(NFC) timing parameters are based on the internal NFC clock generated by the Clock Controller module,
where time T is the period of the NFC clock in ns. Per the i.MX21S Reference Manual, specifically the
Phase-Locked (PLL), Clock, and Reset Controller chapter, the NFC clock is derived from the same clock
which drives the CPU clock (FCLK) that is fed through the NFCDIV block to generate the NFC clock.
The relationship between the NFC clock and the external timing parameters of the NFC is provided in
Table 24.
Table 24 also provides two examples of external timing parameters with NFC clock frequencies of
22.17 MHz and 33.25 MHz. For example, assuming a 266 MHz FCLK (CPU clock), NFCDIV should be
set to divide-by-12 to generate a 22.17 MHz NFC clock and divide-by-8 to generate a 33.25 MHz NFC
clock. The user should compare the parameters of the selected NAND Flash memory with the NFC
external timing parameters to determine the proper NFC clock. The maximum NFC clock allowed is
66 MHz. It should also be noted that the default NFC clock on power up is 16.63 MHz.
NFCLE
NF1
NF3
NF2
NF4
NFCE
NF5
NFWE
NF6
NF7
NF9
NFALE
NF8
command
NFIO[7:0]
Figure 25. Command Latch Cycle Timing DIagram
MC9328MX21S Technical Data, Rev. 1.3
34
Freescale Semiconductor
Specifications
NFCLE
NFCE
NF1
NF3
NF4
NF5
NFWE
NF6
NF7
NF9
NFALE
NF8
NFIO[7:0]
Address
Address
Time it takes for SW to issue the next address command
Figure 26. Address Latch Cycle Timing DIagram
NFCLE
NFCE
NF1
NF3
NF4
NF10
NF11
NF5
NF8
NFWE
NFALE
NF6
NF9
NFIO[15:0]
Data to Flash
Figure 27. Write Data Latch Timing DIagram
NFCLE
NFCE
NF14
NF3
NF13
NF15
NFRE
NF16
NF17
NFRB
Data from Flash
NFIO[15:0]
NF12
Figure 28. Read Data Latch Timing Diagram
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
35
Specifications
1 2
Table 24. NFC Target Timing Parameters ,
Relationshipto NFC
Clock Period
(T)
NFC Clock
22.17 MHz
T = 45 ns
NFC Clock
33.25 MHz
T = 30 ns
ID
Parameter
Symbol
Unit
Min
Max
Min
Max
Min
Max
NF1 NFCLE Setup Time
NF2 NFCLE Hold Time
NF3 NFCE Setup Time
NF4 NFCE Hold Time
NF5 NF_WP Pulse Width
NF6 NFALE Setup Time
NF7 NFALE Hold Time
NF8 Data Setup Time
NF9 Data Hold Time
tCLS
tCLH
tCS
T
T
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
45
45
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
30
30
30
30
30
30
30
30
30
60
30
120
45
60
15
15
0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
T
45
tCH
T
45
tWP
tALS
tALH
tDS
T
45
T
45
T
45
T
45
tDH
T
45
NF10 Write Cycle Time
NF11 NFWE Hold Time
NF12 Ready to NFRE Low
NF13 NFRE Pulse Width
NF14 READ Cycle Time
NF15 NFRE High Hold Time
NF16 Data Setup on READ
NF17 Data Hold on READ
tWC
tWH
tRR
2T
T
90
45
4T
1.5T
2T
0.5T
15
0
180
67.5
90
tRP
tRC
tREH
tDSR
tDHR
22.5
15
0
1. High is defined as 80% of signal value and low is defined as 20% of signal value. All timings are listed according to this NFC
clock frequency (multiples of NFC clock period) except NF16, which is not NFC clock related.
2. The read data is generated by the NAND Flash device and sampled with the internal NFC clock.
MC9328MX21S Technical Data, Rev. 1.3
36
Freescale Semiconductor
Specifications
3.13 Pulse-Width Modulator
The PWM can be programmed to select one of two clock signals as its source frequency. The selected
clock signal is passed through a divider and a prescaler before being input to the counter. The output is
available at the pulse-width modulator output (PWMO) external pin.
1
2a
3b
System Clock
2b
4b
3a
4a
PWM Output
Figure 29. PWM Output Timing Diagram
Table 25. PWM Output Timing Parameters
1.8 V 0.1 V
3.0 V 0.3 V
Ref No.
Parameter
Unit
Minimum
Maximum
Minimum
Maximum
1
1
System CLK frequency
0
12.29
9.91
–
45
–
0
12.29
9.91
–
45
–
MHz
ns
1
2a
2b
3a
3b
4a
4b
Clock high time
1
Clock low time
–
–
ns
1
Clock fall time
0.5
0.5
–
0.5
0.5
–
ns
1
Clock rise time
–
–
ns
1
Output delay time
9.37
8.71
3.61
3.03
ns
1
Output setup time
–
–
ns
1. CL of PWMO = TBD
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
37
Specifications
3.14 SDRAM Memory Controller
The following figures (Figure 30 through Figure 33) and their associated tables specify the timings related
to the SDRAMC module in the i.MX21S.
1
SDCLK
2
3S
3
CS
RAS
CAS
3H
3S
3S
3H
3S
3H
3H
4H
WE
ADDR
DQ
4S
ROW/BA
COL/BA
5
8
6
Data
7
3S
DQM
3H
Note: CKE is high during the read/write cycle.
Figure 30. SDRAM Read Cycle Timing Diagram
Table 26. SDRAM Read Cycle Timing Parameter
1.8 V 0.1 V
3.0 V 0.3 V
Ref
No.
Parameter
Unit
Minimum
Maximum
Minimum
Maximum
1
2
3
SDRAM clock high-level width
SDRAM clock low-level width
SDRAM clock cycle time
3.00
3.00
7.5
–
–
–
–
–
3
3
–
–
–
–
–
ns
ns
ns
ns
ns
7.5
3
3S CS, RAS, CAS, WE, DQM setup time
3H CS, RAS, CAS, WE, DQM hold time
4.78
3.03
2
MC9328MX21S Technical Data, Rev. 1.3
38
Freescale Semiconductor
Specifications
Table 26. SDRAM Read Cycle Timing Parameter (Continued)
1.8 V 0.1 V
3.0 V 0.3 V
Minimum Maximum
Ref
No.
Parameter
Unit
Minimum
Maximum
4S Address setup time
4H Address hold time
3.67
2.95
–
–
–
2
2
–
–
–
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
–
5
5
5
6
7
7
7
8
SDRAM access time (CL = 3)
5.4
5.4
SDRAM access time (CL = 2)
–
6.0
6.0
SDRAM access time (CL = 1)
–
–
–
Data out hold time
–
–
2
2
1
1
Data out high-impedance time (CL = 3)
Data out high-impedance time (CL = 2)
Data out high-impedance time (CL = 1)
Active to read/write command period (RC = 1)
–
t
t
–
t
t
HZ
HZ
1
1
–
–
–
HZ
HZ
–
–
–
2
2
t
–
t
–
RCD
RCD
1. t = SDRAM data out high-impedance time, external SDRAM memory device dependent parameter.
HZ
2. t
= SDRAM clock cycle time. The t
SDCLK
setting can be found in the i.MX21S reference manual.
RCD
RCD
1
3
2
CS
RAS
6
CAS
WE
4
5
7
ADDR
/ BA
ROW/BA
COL/BA
DATA
8
9
DQ
DQM
Figure 31. SDRAM Write Cycle Timing Diagram
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
39
Specifications
Table 27. SDRAM Write Cycle Timing Parameter
1.8 V 0.1 V
3.0 V 0.3 V
Ref
No.
Parameter
Unit
Minimum
Maximum
Minimum
Maximum
1
2
3
4
5
6
7
8
9
SDRAM clock high-level width
SDRAM clock low-level width
SDRAM clock cycle time
Address setup time
3.00
3.00
7.5
–
–
–
–
–
–
–
–
–
3
3
–
–
–
–
–
–
–
–
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
7.5
2
3.67
Address hold time
2.95
2
1
2
2
Precharge cycle period
t
t
RP
RP
2
2
Active to read/write command delay
Data setup time
t
t
RCD
RCD
3.41
2
Data hold time
2.45
2
1. Precharge cycle timing is included in the write timing diagram.
2. t and t
= SDRAM clock cycle time. These settings can be found in the i.MX21 reference manual.
RCD
RP
SDCLK
CS
1
3
2
RAS
CAS
6
7
7
WE
ADDR
DQ
4
5
BA
ROW/BA
DQM
Figure 32. SDRAM Refresh Timing Diagram
MC9328MX21S Technical Data, Rev. 1.3
40
Freescale Semiconductor
Specifications
Table 28. SDRAM Refresh Timing Parameters
1.8 V 0.1 V
3.0 V 0.3 V
Ref
No.
Parameter
Unit
Minimum
Maximum
Minimum
Maximum
1
2
3
4
5
6
7
SDRAM clock high-level width
SDRAM clock low-level width
SDRAM clock cycle time
Address setup time
3.00
3.00
7.5
–
–
–
–
–
–
–
3
3
–
–
–
–
–
–
–
ns
ns
ns
ns
ns
ns
ns
7.5
2
3.67
Address hold time
2.95
2
1
1
Precharge cycle period
Auto precharge command period
t
t
RP
RP
1
1
t
t
RC
RC
1. t and t = SDRAM clock cycle time. These settings can be found in the i.MX21 reference manual.
RP
RC
SDCLK
CS
RAS
CAS
WE
ADDR
DQ
BA
DQM
CKE
Figure 33. SDRAM Self-Refresh Cycle Timing Diagram
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
41
Specifications
3.15 Synchronous Serial Interface
The transmit and receive sections of the SSI can be synchronous or asynchronous. In synchronous mode,
the transmitter and the receiver use a common clock and frame synchronization signal. In asynchronous
mode, the transmitter and receiver each have their own clock and frame synchronization signals.
Continuous or gated clock mode can be selected. In continuous mode, the clock runs continuously. In gated
clock mode, the clock functions only during transmission. The internal and external clock timing diagrams
are shown in Figure 34 through Figure 37.
Normal or network mode can also be selected. In normal mode, the SSI functions with one data word of
I/O per frame. In network mode, a frame can contain between 2 and 32 data words. Network mode is
typically used in star or ring-time division multiplex networks with other processors or codecs, allowing
interface to time division multiplexed networks without additional logic. Use of the gated clock is not
allowed in network mode. These distinctions result in the basic operating modes that allow the SSI to
communicate with a wide variety of devices.
The SSI can be connected to 4 set of ports, SAP, SSI1, SSI2 and SSI3.
1
CK Output
4
2
FS (bl) Output
FS (wl) Output
6
8
12
10
11
32
STXD Output
SRXD Input
31
Note: SRXD input in synchronous mode only.
Figure 34. SSI Transmitter Internal Clock Timing Diagram
MC9328MX21S Technical Data, Rev. 1.3
42
Freescale Semiconductor
Specifications
1
CK Output
3
5
FS (bl) Output
FS (wl) Output
7
9
13
14
SRXD Input
Figure 35. SSI Receiver Internal Clock Timing Diagram
15
16
17
CK Input
18
20
FS (bl) Input
FS (wl) Input
24
22
28
27
34
26
STXD Output
SRXD Input
33
Note: SRXD Input in Synchronous mode only
Figure 36. SSI Transmitter External Clock Timing Diagram
15
16
17
CK Input
19
21
FS (bl) Input
FS (wl) Input
25
23
30
29
SRXD Input
Figure 37. SSI Receiver External Clock Timing Diagram
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
43
Specifications
Table 29. SSI to SAP Ports Timing Parameters
1.8 V 0.1 V
3.0 V 0.3 V
Ref
No.
Parameter
Unit
Minimum
Maximum
Minimum
Maximum
1
Internal Clock Operation (SAP Ports)
1
1
2
(Tx/Rx) CK clock period
90.91
-3.30
-3.93
-3.30
-3.93
-3.30
-3.93
-3.30
-3.93
-2.44
-2.44
-2.44
-2.67
23.68
0
–
90.91
-2.98
-4.18
-2.98
-4.18
-2.98
-4.18
-2.98
-4.18
-2.65
-2.65
-2.65
-2.65
22.09
0
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
(Tx) CK high to FS (bl) high
-1.16
-1.34
-1.16
-1.34
-1.16
-1.34
-1.16
-1.34
-0.60
-0.60
-0.60
-0.99
–
-1.10
-1.43
-1.10
-1.43
-1.10
-1.43
-1.10
-1.43
-0.98
-0.98
-0.98
-0.98
–
3
(Rx) CK high to FS (bl) high
(Tx) CK high to FS (bl) low
4
5
(Rx) CK high to FS (bl) low
6
(Tx) CK high to FS (wl) high
(Rx) CK high to FS (wl) high
(Tx) CK high to FS (wl) low
7
8
9
(Rx) CK high to FS (wl) low
10
(Tx) CK high to STXD valid from high impedance
11a (Tx) CK high to STXD high
11b (Tx) CK high to STXD low
12
13
14
(Tx) CK high to STXD high impedance
SRXD setup time before (Rx) CK low
SRXD hold time after (Rx) CK low
–
–
External Clock Operation (SAP Ports)
1
15
16
17
18
19
20
21
22
23
24
25
26
(Tx/Rx) CK clock period
90.91
36.36
36.36
10.24
10.89
10.24
10.89
10.24
10.89
10.24
10.89
12.08
10.80
10.80
12.08
0.37
–
90.91
36.36
36.36
7.16
7.63
7.16
7.63
7.16
7.63
7.16
7.63
7.71
7.71
7.71
7.71
0.42
0
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
(Tx/Rx) CK clock high period
(Tx/Rx) CK clock low period
(Tx) CK high to FS (bl) high
(Rx) CK high to FS (bl) high
(Tx) CK high to FS (bl) low
–
–
–
–
19.50
21.27
19.50
21.27
19.50
21.27
19.50
21.27
19.36
19.36
19.36
19.36
–
8.65
9.12
8.65
9.12
8.65
9.12
8.65
9.12
9.20
9.20
9.20
9.20
–
(Rx) CK high to FS (bl) low
(Tx) CK high to FS (wl) high
(Rx) CK high to FS (wl) high
(Tx) CK high to FS (wl) low
(Rx) CK high to FS (wl) low
(Tx) CK high to STXD valid from high impedance
27a (Tx) CK high to STXD high
27b (Tx) CK high to STXD low
28
29
30
(Tx) CK high to STXD high impedance
SRXD setup time before (Rx) CK low
SRXD hole time after (Rx) CK low
0
–
–
MC9328MX21S Technical Data, Rev. 1.3
44
Freescale Semiconductor
Specifications
Unit
Table 29. SSI to SAP Ports Timing Parameters (Continued)
1.8 V 0.1 V
Minimum Maximum
Synchronous Internal Clock Operation (SAP Ports)
3.0 V 0.3 V
Minimum
Ref
No.
Parameter
Maximum
31
32
SRXD setup before (Tx) CK falling
SRXD hold after (Tx) CK falling
23.00
0
–
–
21.41
0
–
–
ns
ns
Synchronous External Clock Operation (SAP Ports)
33
34
SRXD setup before (Tx) CK falling
SRXD hold after (Tx) CK falling
1.20
0
–
–
0.88
0
–
–
ns
ns
1. All the timings for the SSI are given for a non-inverted serial clock polarity (TSCKP/RSCKP = 0) and a non-inverted frame sync
(TFSI/RFSI = 0). If the polarity of the clock and/or the frame sync have been inverted, all the timing remains valid by inverting
the clock signal STCK/SRCK and/or the frame sync STFS/SRFS shown in the tables and in the figures.
Table 30. SSI to SSI1 Ports Timing Parameters
1.8 V 0.1 V
Minimum Maximum
Internal Clock Operation (SSI1 Ports)
3.0 V 0.3 V
Ref
No.
Parameter
Unit
Minimum
Maximum
1
1
1
2
(Tx/Rx) CK clock period
90.91
-0.68
-0.96
-0.68
-0.96
-0.68
-0.96
-0.68
-0.96
-1.68
-1.68
-1.68
-1.58
20.41
0
–
90.91
-0.68
-0.96
-0.68
-0.96
-0.68
-0.96
-0.68
-0.96
-1.68
-1.68
-1.68
-1.58
20.41
0
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
(Tx) CK high to FS (bl) high
(Rx) CK high to FS (bl) high
(Tx) CK high to FS (bl) low
-0.15
-0.27
-0.15
-0.27
-0.15
-0.27
-0.15
-0.27
-0.36
-0.36
-0.36
-0.31
–
-0.15
-0.27
-0.15
-0.27
-0.15
-0.27
-0.15
-0.27
-0.36
-0.36
-0.36
-0.31
–
3
4
5
(Rx) CK high to FS (bl) low
6
(Tx) CK high to FS (wl) high
(Rx) CK high to FS (wl) high
(Tx) CK high to FS (wl) low
7
8
9
(Rx) CK high to FS (wl) low
(Tx) CK high to STXD valid from high impedance
10
11a (Tx) CK high to STXD high
11b (Tx) CK high to STXD low
12
13
14
(Tx) CK high to STXD high impedance
SRXD setup time before (Rx) CK low
SRXD hold time after (Rx) CK low
–
–
External Clock Operation (SSI1 Ports)
1
15
16
17
18
19
(Tx/Rx) CK clock period
90.91
36.36
36.36
10.22
10.79
–
90.91
36.36
36.36
8.82
–
–
ns
ns
ns
ns
ns
(Tx/Rx) CK clock high period
(Tx/Rx) CK clock low period
(Tx) CK high to FS (bl) high
(Rx) CK high to FS (bl) high
–
–
–
17.63
19.67
16.24
18.28
9.39
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
45
Specifications
Table 30. SSI to SSI1 Ports Timing Parameters (Continued)
1.8 V 0.1 V
3.0 V 0.3 V
Ref
No.
Parameter
(Tx) CK high to FS (bl) low
Unit
Minimum
Maximum
Minimum
Maximum
20
21
22
23
24
25
26
10.22
10.79
10.22
10.79
10.22
10.79
10.05
10.00
10.00
10.05
0.78
17.63
19.67
17.63
19.67
17.63
19.67
15.75
15.63
15.63
15.75
–
8.82
9.39
8.82
9.39
8.82
9.39
8.66
8.61
8.61
8.66
0.47
0
16.24
18.28
16.24
18.28
16.24
18.28
14.36
14.24
14.24
14.36
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
(Rx) CK high to FS (bl) low
(Tx) CK high to FS (wl) high
(Rx) CK high to FS (wl) high
(Tx) CK high to FS (wl) low
(Rx) CK high to FS (wl) low
(Tx) CK high to STXD valid from high impedance
27a (Tx) CK high to STXD high
27b (Tx) CK high to STXD low
28
29
30
(Tx) CK high to STXD high impedance
SRXD setup time before (Rx) CK low
SRXD hole time after (Rx) CK low
0
–
–
Synchronous Internal Clock Operation (SSI1 Ports)
31
32
SRXD setup before (Tx) CK falling
SRXD hold after (Tx) CK falling
19.90
0
–
–
19.90
0
–
–
ns
ns
Synchronous External Clock Operation (SSI1 Ports)
33
34
SRXD setup before (Tx) CK falling
SRXD hold after (Tx) CK falling
2.59
0
–
–
2.28
0
–
–
ns
ns
1. All the timings for the SSI are given for a non-inverted serial clock polarity (TSCKP/RSCKP = 0) and a non-inverted frame sync
(TFSI/RFSI = 0). If the polarity of the clock and/or the frame sync have been inverted, all the timing remains valid by inverting
the clock signal STCK/SRCK and/or the frame sync STFS/SRFS shown in the tables and in the figures.
Table 31. SSI to SSI2 Ports Timing Parameters
1.8 V 0.1 V
Minimum Maximum
Internal Clock Operation (SSI2 Ports)
3.0 V 0.3 V
Ref
No.
Parameter
Unit
Minimum
Maximum
1
1
1
2
(Tx/Rx) CK clock period
90.91
0.01
-0.21
0.01
-0.21
0.01
-0.21
0.01
-0.21
0.34
–
90.91
0.01
-0.21
0.01
-0.21
0.01
-0.21
0.01
-0.21
0.34
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
(Tx) CK high to FS (bl) high
(Rx) CK high to FS (bl) high
(Tx) CK high to FS (bl) low
0.15
0.05
0.15
0.05
0.15
0.05
0.15
0.05
0.72
0.15
0.05
0.15
0.05
0.15
0.05
0.15
0.05
0.72
3
4
5
(Rx) CK high to FS (bl) low
6
(Tx) CK high to FS (wl) high
(Rx) CK high to FS (wl) high
(Tx) CK high to FS (wl) low
7
8
9
(Rx) CK high to FS (wl) low
(Tx) CK high to STXD valid from high impedance
10
MC9328MX21S Technical Data, Rev. 1.3
46
Freescale Semiconductor
Specifications
Unit
Table 31. SSI to SSI2 Ports Timing Parameters (Continued)
1.8 V 0.1 V
3.0 V 0.3 V
Minimum
Ref
No.
Parameter
Minimum
Maximum
Maximum
11a (Tx) CK high to STXD high
11b (Tx) CK high to STXD low
0.34
0.34
0.34
21.50
0
0.72
0.72
0.48
–
0.34
0.34
0.34
21.50
0
0.72
0.72
0.48
–
ns
ns
ns
ns
ns
12
13
14
(Tx) CK high to STXD high impedance
SRXD setup time before (Rx) CK low
SRXD hold time after (Rx) CK low
–
–
External Clock Operation (SSI2 Ports)
1
15
16
17
18
19
20
21
22
23
24
25
26
(Tx/Rx) CK clock period
90.91
36.36
36.36
10.40
11.00
10.40
11.00
10.40
11.00
10.40
11.00
9.59
–
90.91
36.36
36.36
8.67
9.28
8.67
9.28
8.67
9.28
8.67
9.28
7.86
7.86
7.86
7.86
2.52
0
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
(Tx/Rx) CK clock high period
(Tx/Rx) CK clock low period
(Tx) CK high to FS (bl) high
(Rx) CK high to FS (bl) high
(Tx) CK high to FS (bl) low
–
–
–
–
17.37
19.70
17.37
19.70
17.37
19.70
17.37
19.70
17.08
17.08
17.08
16.84
–
15.88
18.21
15.88
18.21
15.88
18.21
15.88
18.21
15.59
15.59
15.59
15.35
–
(Rx) CK high to FS (bl) low
(Tx) CK high to FS (wl) high
(Rx) CK high to FS (wl) high
(Tx) CK high to FS (wl) low
(Rx) CK high to FS (wl) low
(Tx) CK high to STXD valid from high impedance
27a (Tx) CK high to STXD high
27b (Tx) CK high to STXD low
9.59
9.59
28
29
30
(Tx) CK high to STXD high impedance
SRXD setup time before (Rx) CK low
SRXD hole time after (Rx) CK low
9.59
2.52
0
–
–
Synchronous Internal Clock Operation (SSI2 Ports)
31
32
SRXD setup before (Tx) CK falling
SRXD hold after (Tx) CK falling
20.78
0
–
–
20.78
0
–
–
ns
ns
Synchronous External Clock Operation (SSI2 Ports)
33
34
SRXD setup before (Tx) CK falling
SRXD hold after (Tx) CK falling
4.42
0
–
–
4.42
0
–
–
ns
ns
1. All the timings for the SSI are given for a non-inverted serial clock polarity (TSCKP/RSCKP = 0) and a non-inverted frame sync
(TFSI/RFSI = 0). If the polarity of the clock and/or the frame sync have been inverted, all the timing remains valid by inverting
the clock signal STCK/SRCK and/or the frame sync STFS/SRFS shown in the tables and in the figures.
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
47
Specifications
Table 32. SSI to SSI3 Ports Timing Parameters
1.8 V 0.1 V
3.0 V 0.3 V
Ref
No.
Parameter
Unit
Minimum
Maximum
Minimum
Maximum
1
Internal Clock Operation (SSI3 Ports)
1
1
2
(Tx/Rx) CK clock period
90.91
-2.09
-2.74
-2.09
-2.74
-2.09
-2.74
-2.09
-2.74
-1.73
-2.87
-2.87
-1.73
22.77
0
–
90.91
-2.09
-2.74
-2.09
-2.74
-2.09
-2.74
-2.09
-2.74
-1.73
-2.87
-2.87
-1.73
22.77
0
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
(Tx) CK high to FS (bl) high
-0.66
-0.84
-0.66
-0.84
-0.66
-0.84
-0.66
-0.84
-0.26
-0.80
-0.80
-0.26
–
-0.66
-0.84
-0.66
-0.84
-0.66
-0.84
-0.66
-0.84
-0.26
-0.80
-0.80
-0.26
–
3
(Rx) CK high to FS (bl) high
(Tx) CK high to FS (bl) low
4
5
(Rx) CK high to FS (bl) low
6
(Tx) CK high to FS (wl) high
(Rx) CK high to FS (wl) high
(Tx) CK high to FS (wl) low
7
8
9
(Rx) CK high to FS (wl) low
10
(Tx) CK high to STXD valid from high impedance
11a (Tx) CK high to STXD high
11b (Tx) CK high to STXD low
12
13
14
(Tx) CK high to STXD high impedance
SRXD setup time before (Rx) CK low
SRXD hold time after (Rx) CK low
–
–
External Clock Operation (SSI3 Ports)
1
15
16
17
18
19
20
21
22
23
24
25
26
(Tx/Rx) CK clock period
90.91
36.36
36.36
9.62
–
90.91
36.36
36.36
7.90
8.58
7.90
8.58
7.90
8.58
7.90
8.58
7.29
6.75
6.75
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
(Tx/Rx) CK clock high period
(Tx/Rx) CK clock low period
(Tx) CK high to FS (bl) high
(Rx) CK high to FS (bl) high
(Tx) CK high to FS (bl) low
–
–
–
–
17.10
19.54
17.10
19.54
17.10
19.54
17.10
19.54
16.46
15.32
15.32
15.61
18.05
15.61
18.05
15.61
18.05
15.61
18.05
14.97
13.83
13.83
10.30
9.62
(Rx) CK high to FS (bl) low
10.30
9.62
(Tx) CK high to FS (wl) high
(Rx) CK high to FS (wl) high
(Tx) CK high to FS (wl) low
(Rx) CK high to FS (wl) low
(Tx) CK high to STXD valid from high impedance
10.30
9.62
10.30
9.02
27a (Tx) CK high to STXD high
27b (Tx) CK high to STXD low
8.48
8.48
MC9328MX21S Technical Data, Rev. 1.3
48
Freescale Semiconductor
Specifications
Table 32. SSI to SSI3 Ports Timing Parameters (Continued)
1.8 V 0.1 V
3.0 V 0.3 V
Minimum Maximum
Ref
No.
Parameter
Unit
Minimum
Maximum
28
29
30
(Tx) CK high to STXD high impedance
SRXD setup time before (Rx) CK low
SRXD hole time after (Rx) CK low
9.02
1.49
0
16.46
7.29
1.49
0
14.97
ns
ns
ns
–
–
–
–
Synchronous Internal Clock Operation (SSI3 Ports)
31
32
SRXD setup before (Tx) CK falling
SRXD hold after (Tx) CK falling
21.99
0
–
–
21.99
0
–
–
ns
ns
Synchronous External Clock Operation (SSI3 Ports)
33
34
SRXD setup before (Tx) CK falling
SRXD hold after (Tx) CK falling
3.80
0
–
–
3.80
0
–
–
ns
ns
1. All the timings for the SSI are given for a non-inverted serial clock polarity (TSCKP/RSCKP = 0) and a non-inverted frame sync
(TFSI/RFSI = 0). If the polarity of the clock and/or the frame sync have been inverted, all the timing remains valid by inverting
the clock signal STCK/SRCK and/or the frame sync STFS/SRFS shown in the tables and in the figures.
3.16 1-Wire Interface Timing
3.16.1 Reset Sequence with Reset Pulse Presence Pulse
To begin any communications with the DS2502, it is required that an initialization procedure be issued. A
reset pulse must be generated and then a presence pulse must be detected. The minimum reset pulse length
is 480 us. The bus master (one-wire) will generate this pulse, then after the DS2502 detects a rising edge
on the one-wire bus, it will wait 15-60 us before it will transmit back a presence pulse. The presence pulse
will exist for 60-240 us.
The timing diagram for this sequence is shown in Figure 38.
Reset and Presence Pulses
AutoClear RPP
Control Bit
DS2502
Set RPP
waits
DS2502 Tx
“presence pulse”
60-240us
511 us
15-60us
one-wire
BUS
512us
One-Wire samples (set PST)
68us
Figure 38. 1-Wire Initialization
The reset pulse begins the initialization sequence and it is initiated when the RPP control register bit is set.
When the presence pulse is detected, this bit will be cleared. The presence pulse is used by the bus master
to determine if at least one DS2502 is connected. Software will determine if more than one DS2502 exists.
The one-wire will sample for the DS2502 presence pulse. The presence pulse is latched in the one-wire
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
49
Specifications
control register PST. When the PST bit is set to a one, it means that a DS2502 is present; if the bit is set to
a zero, then no device was found.
3.16.2 Write 0
The Write 0 function simply writes a zero bit to the DS2502. The sequence takes 117 us. The one-wire bus
is held low for 100us.
AutoClear WR0
Set WR0
Write 0 Slot 128us
17us
100us
one-wire
BUS
Figure 39. Write 0 Timing
The Write 0 pulse sequence is initiated when the WR0 control bit register is set. When the write is
complete, the WR0 register will be auto cleared.
3.16.3 Write 1/Read Data
The Write 1 and Read timing is identical. The time slot is first driven low. According to the DS2502
documentation, the DS2502 has a delay circuit which is used to synchronize the DS2502 with the bus
master (one-wire). This delay circuit is triggered by the falling edge of the data line and is used to decide
when the DS2502 should sample the line. In the case of a write 1 or read 1, after a delay, a 1 will be
transmitted / received. When a read 0 slot is issued, the delay circuit will hold the data line low to override
the 1 generated by the bus master (one-wire).
For the Write 1 or Read, the control register WR1/RD is set and auto-cleared when the sequence has been
completed. After a Read, the control register RDST bit is set to the value of the read.
Auto Clear WR1/R
Set WR1/RD
Write “1” Slot 117us
5us
Figure 40. Write 1 Timing
MC9328MX21S Technical Data, Rev. 1.3
50
Freescale Semiconductor
Specifications
Set WR1/RD
Auto Clear WR1/RD Set WR1/RD
Auto Clear WR1/R
Read Timing
Read “0” Slot 117us
60us
Read “1” Slot 117us
one-wire
BUS
5us
13us
5us
13us
One-Wire samples
(set RDST)
One-Wire samples
(set RDST)
Figure 41. Read Timing
The precision of the generated clock is very important to get a proper behavior of the one-wire module.
This module is based on a state machine which undertakes actions at defined times.
Table 33. System Timing Requirements
Values
(Microsec)
Minimum
(Microsec)
Maximum
(microsec)
Absolute
Precision
Relative
Precision
Times
RSTL
PST
511
68
480
60
480
60
1
–
75
–
31
7
0.0645
0.1
RSTH
512
100
5
32
20
4
0.0645
0.2
LOW0
120
15
15
LOWR
0.8
READ_sample
13
–
2
0.15
The most stringent constraint is 0.0645 as a relative time imprecision.
The time relative precision is directly derived from the frequency of the derivative clock (f):
Time relative precision = 1/f -1 = divider/clock (MHz) - 1
The Figure 34 gathers relative time precision for different main clock frequencies.
Table 34. System Clock Requirements
Main Clock Frequency (MHz)
13
16.8
19.44
Clock divide ratio
13
1
17
19
Generated frequency (MHz)
Relative time imprecision
0.9882
0.0117
1.023
0.023
0
This shows that the user should take care of the main clock frequency when using the one-wire module. If
the main clock is an exact integer multiple of 1 MHz, then the generated frequency will be exactly 1 MHz.
NOTE:
A main clock frequency below 10 MHz might cause a misbehavior of the module.
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
51
Specifications
3.17 USB On-The-Go
Four types of data transfer modes exist for the USB module: control transfers, bulk transfers, isochronous
transfers and interrupt transfers. From the perspective of the USB module, the interrupt transfer type is
identical to the bulk data transfer mode, and no additional hardware is supplied to support it. This section
covers the transfer modes and how they work from the ground up.
Data moves across the USB in packets. Groups of packets are combined to form data transfers. The same
packet transfer mechanism applies to bulk, interrupt, and control transfers. Isochronous data is also moved
in the form of packets, but because isochronous pipes are given a fixed portion of the USB bandwidth at
all times, there is no end-of-transfer.
USB_ON
(Output)
t
TXDM_OEB
4
t
1
OEB_TXDP
USB_OE
(Output)
6
3
t
t
PERIOD
TXDP_OEB
USB_TXDP
(Output)
USB_TXDM
(Output)
t
OEB_TXDM
t
FEOPT
2
5
USB_VP
(Input)
USB_VM
(Input)
Figure 42. USB Timing Diagram for Data Transfer to USB Transceiver (TX)
Table 35. USB Timing Parameters for Data Transfer to USB Transceiver (TX)
3.0 V 0.3 V
Ref
No.
Parameter
Unit
Minimum
Maximum
1
2
3
4
5
6
tOEB
; USBD_OE active to USBD_TXDP low
; USBD_OE active to USBD_TXDM high
83.14
81.55
83.54
248.9
160
83.47
81.98
83.8
ns
ns
_TXDP
tOEB
_TXDM
t
t
t
t
OEB; USBD_TXDP high to USBD_OE deactivated
ns
TXDP_
TXDM_
FEOPT
PERIOD
OEB; USBD_TXDM low to USBD_OE deactivated (includes SE0)
; SE0 interval of EOP
249.13
175
ns
ns
; Data transfer rate
11.97
12.03
Mb/s
MC9328MX21S Technical Data, Rev. 1.3
52
Freescale Semiconductor
Specifications
USB_ON
(Output)
USB_OE
(Output)
USB_TXDP
(Output)
USB_TXDM
(Output)
1
t
FEOPR
USB_RXDP
(Input)
USB_RXDM
(Input)
Figure 43. USB Timing Diagram for Data Transfer from USB Transceiver (RX)
Table 36. USB Timing Parameters for Data Transfer from USB Transceiver (RX)
3.0 V 0.3 V
Ref No.
Parameter
Unit
Minimum
Maximum
1
t
; Receiver SE0 interval of EOP
82
–
ns
FEOPR
2
The USBOTG I C communication protocol consists of six components: START, Data Source/Recipient,
Data Direction, Slave Acknowledge, Data, Data Acknowledge, and STOP.
USBG_SDA
5
3
4
USBG_SCL
1
2
6
2
Figure 44. USB Timing Diagram for Data Transfer from USB Transceiver (I C)
2
Table 37. USB Timing Parameters for Data Transfer from USB Transceiver (I C)
1.8 V 0.1 V
Ref No.
Parameter
Unit
Minimum
Maximum
1
2
3
4
5
6
Hold time (repeated) START condition
Data hold time
188
0
–
188
–
ns
ns
ns
ns
ns
ns
Data setup time
88
HIGH period of the SCL clock
LOW period of the SCL clock
Setup time for STOP condition
500
500
185
–
–
–
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
53
Specifications
3.18 External Interface Module (EIM)
The External Interface Module (EIM) handles the interface to devices external to the i.MX21S, including
generation of chip-selects for external peripherals and memory. The timing diagram for the EIM is shown
in Figure 45, and Table 38 defines the parameters of signals.
(HCLK) Bus Clock
1a
2a
3a
1b
2b
3b
Address
Chip-select
Read (Write)
4a
5a
4b
5b
OE (rising edge)
4c
5c
4d
OE (falling edge)
EB (rising edge)
EB (falling edge)
5d
6b
6a
6a
LBA (negated falling edge)
LBA (negated rising edge)
6c
7a
7b
11
Burst Clock (rising edge)
7c
7d
Burst Clock (falling edge)
Read Data
8b
9a
9a
8a
9b
Write Data (negated falling)
9c
Write Data (negated rising)
DTACK
10a
10a
Figure 45. EIM Bus Timing Diagram
MC9328MX21S Technical Data, Rev. 1.3
54
Freescale Semiconductor
Specifications
Table 38. EIM Bus Timing Parameters
1.8 V 0.1 V 3.0 V 0.3 V
1.8 V
0.1 V
Ref No.
Parameter
Unit
Min
Typical
Max
Min
Typical
Max
1a
1b
2a
2b
3a
3b
4a
4b
4c
4d
5a
5b
5c
5d
6a
6b
6c
7a
7b
7c
7d
8a
8b
9a
9b
9c
10a
11
Clock fall to address valid
3.97
3.93
3.47
3.39
3.51
3.59
3.62
3.70
3.60
3.69
3.69
4.64
3.52
3.50
3.65
3.65
3.66
3.50
3.49
3.50
3.49
4.54
0.5
6.02
6.00
5.59
5.09
5.56
5.37
5.49
5.61
5.48
5.62
5.46
5.47
5.06
5.05
5.28
5.67
5.69
5.22
5.19
5.22
5.19
–
9.89
9.86
8.62
8.27
8.79
9.14
8.98
9.26
8.77
9.12
8.71
8.70
8.39
8.27
8.69
9.36
9.48
8.42
8.30
8.39
8.29
–
3.83
3.81
3.30
3.15
3.39
3.36
3.46
3.46
3.44
3.42
3.46
3.46
3.41
3.41
3.30
3.41
3.33
3.26
3.31
3.26
3.31
4.54
0.5
5.89
5.86
5.09
4.85
5.39
5.20
5.33
5.37
5.30
5.36
5.25
5.25
5.18
5.18
5.23
5.43
5.47
4.99
5.03
4.98
5.02
–
9.79
9.76
8.45
8.03
8.51
8.50
9.02
8.81
8.88
8.60
8.54
8.54
8.36
8.36
8.81
9.13
9.25
8.19
8.17
8.15
8.12
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Clock fall to address invalid
Clock fall to chip-select valid
Clock fall to chip-select invalid
Clock fall to Read (Write) Valid
Clock fall to Read (Write) Invalid
1
Clock rise to Output Enable Valid
1
Clock rise to Output Enable Invalid
1
Clock fall to Output Enable Valid
1
Clock fall to Output Enable Invalid
1
Clock rise to Enable Bytes Valid
1
Clock rise to Enable Bytes Invalid
1
Clock fall to Enable Bytes Valid
1
Clock fall to Enable Bytes Invalid
1
Clock fall to Load Burst Address Valid
1
Clock fall to Load Burst Address Invalid
1
Clock rise to Load Burst Address Invalid
1
Clock rise to Burst Clock rise
1
Clock rise to Burst Clock fall
1
Clock fall to Burst Clock rise
1
Clock fall to Burst Clock fall
Read Data setup time
Read Data hold time
–
–
–
–
1
Clock rise to Write Data Valid
4.13
4.10
4.02
2.65
15
5.86
5.79
5.81
4.63
–
9.16
9.15
9.37
8.40
–
3.95
4.04
4.22
2.64
15
6.36
6.27
5.29
4.61
–
10.31
9.16
9.24
8.41
–
1
Clock fall to Write Data Invalid
1
Clock rise to Write Data Invalid
DTACK setup time
Burst Clock (BCLK) cycle time
1. Clock refers to the system clock signal, HCLK, generated from the System DPLL
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
55
Specifications
3.18.1 EIM External Bus Timing Diagrams
The following timing diagrams show the timing of accesses to memory or a peripheral.
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[0]
htrans
hwrite
Seq/Nonseq
Read
haddr
hready
V1
weim_hrdata
weim_hready
Last Valid Data
V1
BCLK
A[24:0]
Last Valid Address
V1
CS[0]
R/W
Read
LBA
OE
EB (EBC=0)
EB (EBC=1)
DATA_IN
V1
Figure 46. WSC = 1, A.HALF/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
56
Freescale Semiconductor
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[0]
htrans
hwrite
haddr
Nonseq
Write
V1
hready
hwdata
Last Valid Data
Write Data (V1)
Unknown
weim_hrdata
Last Valid Data
weim_hready
BCLK
A[24:0]
Last Valid Address
V1
CS[0]
R/W
LBA
Write
OE
EB
D[31:0]
Last Valid Data
Write Data (V1)
Figure 47. WSC = 1, WEA = 1, WEN = 1, A.HALF/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
57
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[0]
htrans
hwrite
haddr
Nonseq
Read
V1
hready
weim_hrdata
Last Valid Data
V1 Word
weim_hready
BCLK
A[24:0]
Last Valid Addr
Address V1
Address V1 + 2
CS[0]
R/W
LBA
OE
Read
EB (EBC=0)
EB (EBC=1)
DATA_IN
1/2 Half Word
2/2 Half Word
Figure 48. WSC = 1, OEA = 1, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
58
Freescale Semiconductor
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[0]
Nonseq
Write
V1
htrans
hwrite
haddr
hready
hwdata
Last Valid Data
Write Data (V1 Word)
Last Valid Data
weim_hrdata
weim_hready
BCLK
A[24:0]
Last Valid Addr
Address V1
Address V1 + 2
CS[0]
R/W
LBA
Write
OE
EB
D[31:0]
1/2 Half Word
2/2 Half Word
Figure 49. WSC = 1, WEA = 1, WEN = 1, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
59
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[3]
htrans
Nonseq
hwrite
Read
V1
haddr
hready
weim_hrdata
Last Valid Data
V1 Word
weim_hready
BCLK
A[24:0]
Last Valid Addr
Address V1
Read
Address V1 + 2
CS[3]
R/W
LBA
OE
EB (EBC=0)
EB (EBC=1)
DATA_IN
1/2 Half Word
2/2 Half Word
Figure 50. WSC = 3, OEA = 2, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
60
Freescale Semiconductor
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[3]
Nonseq
htrans
hwrite
Write
V1
haddr
hready
hwdata
Last Valid
Data
Write Data (V1 Word)
Last Valid Data
weim_hrdata
weim_hready
BCLK
A[24:0]
Last Valid Addr
Address V1
Address V1 + 2
CS[3]
R/W
Write
LBA
OE
EB
D[31:0]
Last Valid Data
1/2 Half Word
2/2 Half Word
Figure 51. WSC = 3, WEA = 1, WEN = 3, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
61
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[2]
htrans
Nonseq
Read
V1
hwrite
haddr
hready
weim_hrdata
Last Valid Data
V1 Word
weim_hready
BCLK
A[24:0]
Last Valid Addr
Address V1
Read
Address V1 + 2
CS[2]
R/W
LBA
OE
EB (EBC=0)
EB (EBC=1)
DATA_IN
1/2 Half Word
2/2 Half Word
Figure 52. WSC = 3, OEA = 4, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
62
Freescale Semiconductor
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[2]
htrans
Nonseq
hwrite
haddr
Write
V1
hready
hwdata
Last Valid
Data
Write Data (V1 Word)
Last Valid Data
weim_hrdata
weim_hready
BCLK
A[24:0] Last Valid Addr
Address V1
Address V1 + 2
CS[2]
R/W
Write
LBA
OE
EB
D[31:0]
Last Valid Data
1/2 Half Word
2/2 Half Word
Figure 53. WSC = 3, WEA = 2, WEN = 3, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
63
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[2]
htrans
Nonseq
Read
V1
hwrite
haddr
hready
weim_hrdata
Last Valid Data
V1 Word
weim_hready
BCLK
A[24:0]
Last Valid Addr
Address V1
Read
Address V1 + 2
CS[2]
R/W
LBA
OE
EB (EBC=0)
EB (EBC=1)
DATA_IN
1/2 Half Word
2/2 Half Word
Figure 54. WSC = 3, OEN = 2, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
64
Freescale Semiconductor
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[2]
htrans
Nonseq
Read
V1
hwrite
haddr
hready
weim_hrdata
Last Valid Data
V1 Word
weim_hready
BCLK
Last Valid Addr
Address V1
Read
Address V1 + 2
A[24:0]
CS[2]
R/W
LBA
OE
EB (EBC=0)
EB (EBC=1)
DATA_IN
1/2 Half Word
2/2 Half Word
Figure 55. WSC = 3, OEA = 2, OEN = 2, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
65
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[2]
htrans
Nonseq
Write
V1
hwrite
haddr
hready
hwdata
Last Valid
Data
Write Data (V1 Word)
Last Valid Data
Unknown
weim_hrdata
weim_hready
BCLK
A[24:0] Last Valid Addr
CS[2]
Address V1
Address V1 + 2
R/W
Write
LBA
OE
EB
D[31:0]
1/2 Half Word
2/2 Half Word
Last Valid Data
Figure 56. WSC = 2, WWS = 1, WEA = 1, WEN = 2, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
66
Freescale Semiconductor
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[2]
Nonseq
Write
V1
htrans
hwrite
haddr
hready
hwdata
Last Valid
Data
Write Data (V1 Word)
Last Valid Data
Unknown
weim_hrdata
weim_hready
BCLK
A[24:0]
Last Valid Addr
Address V1
Address V1 + 2
CS[2]
R/W
LBA
Write
OE
EB
D[31:0]
1/2 Half Word
2/2 Half Word
Last Valid Data
Figure 57. WSC = 1, WWS = 2, WEA = 1, WEN = 2, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
67
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[2]
htrans
Nonseq
Read
V1
Nonseq
Write
V8
hwrite
haddr
hready
hwdata
Last Valid Data
Write Data
Read Data
weim_hrdata
Last Valid Data
weim_hready
BCLK
A[24:0]
Last Valid Addr
Address V1
Address V8
CS[2]
R/W
LBA
Read
Write
OE
EB (EBC=0)
EB (EBC=1)
DATA_IN
D[31:0]
Read Data
Last Valid Data
Write Data
Figure 58. WSC = 2, WWS = 2, WEA = 1, WEN = 2, A.HALF/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
68
Freescale Semiconductor
Specifications
Note: Signals listed with lower case letters are internal to the device.
Read Idle
Write
hclk
hselm_weim_cs[2]
htrans
Nonseq
Read
V1
Nonseq
Write
V8
hwrite
haddr
hready
hwdata
Last Valid Data
Write Data
weim_hrdata
weim_hready
Last Valid Data
Read Data
BCLK
A[24:0]
Last Valid Addr
Address V1
Address V8
Write
CS[2]
R/W
LBA
Read
OE
EB (EBC=0)
EB (EBC=1)
DATA_IN
D[31:0]
Read Data
Last Valid Data
Write Data
Figure 59. WSC = 2, WWS = 1, WEA = 1, WEN = 2, EDC = 1, A.HALF/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
69
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[4]
htrans
Nonseq
Write
V1
hwrite
haddr
hready
hwdata
Last Valid
Data
Write Data (Word)
Last Valid Data
weim_hrdata
weim_hready
BCLK
A[24:0]
Last Valid Addr
Address V1
Address V1 + 2
CS[3:0]
R/W
Write
LBA
OE
EB
D[31:0]
Write Data (1/2 Half Word)
Write Data (2/2 Half Word)
Last Valid Data
Figure 60. WSC = 2, CSA = 1, WWS = 1, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
70
Freescale Semiconductor
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[4]
Nonseq
Read
V1
Nonseq
Write
V8
htrans
hwrite
haddr
hready
hwdata
weim_hrdata
weim_hready
Last Valid Data
Write Data
Read Data
Last Valid Data
BCLK
A[24:0] Last Valid Addr
Address V1
Address V8
CS[4]
R/W
LBA
OE
Read
Write
EB (EBC=0)
EB (EBC=1)
Read Data
DATA_IN
D[31:0]
Last Valid Data
Write Data
Figure 61. WSC = 3, CSA = 1, A.HALF/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
71
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[4]
htrans
Nonseq
Read
V1
Idle
Seq
Read
V2
hwrite
haddr
hready
weim_hrdata
weim_hready
Last Valid Data
Read Data (V1)
Read Data (V2)
BCLK
A[24:0]
Last Valid Addr
Address V1
Address V2
CNC
CS[4]
R/W
LBA
Read
OE
EB (EBC=0)
EB (EBC=1)
DATA_IN
Read Data
(V1)
Read Data
(V2)
Figure 62. WSC = 2, OEA = 2, CNC = 3, BCM = 1, A.HALF/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
72
Freescale Semiconductor
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[4]
htrans
Nonseq
Read
V1
Idle
Nonseq
Write
V8
hwrite
haddr
hready
hwdata
Last Valid Data
Write Data
weim_hrdata
Last Valid Data
Read Data
weim_hready
BCLK
A[24:0]
Last Valid Addr
Address V1
Address V8
CNC
CS[4]
R/W
Read
Write
LBA
OE
EB (EBC=0)
EB (EBC=1)
DATA_IN
D[31:0]
Read Data
Last Valid Data
Write Data
Figure 63. WSC = 2, OEA = 2, WEA = 1, WEN = 2, CNC = 3, A.HALF/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
73
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[2]
htrans
Idle
Nonseq
Read
V1
Nonseq
Read
V5
hwrite
haddr
hready
weim_hrdata
weim_hready
BCLK
A[24:0]
Last Valid Addr
Address V1
Address V5
CS[2]
Read
R/W
LBA
OE
EB (EBC=0)
EB (EBC=1)
ECB
V5 Word
DATA_IN
V6 Word
V1 Word V2 Word
Figure 64. WSC = 3, SYNC = 1, A.HALF/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
74
Freescale Semiconductor
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[2]
htrans
hwrite
haddr
Nonseq
Idle
Seq
Read
V2
Seq
Read
V3
Seq
Read
V4
Read
V1
hready
weim_hrdata
weim_hready
BCLK
Last Valid Data
V1 Word
V2 Word
V3 Word
V4 Word
A[24:0]
Last Valid Addr
Address V1
CS[2]
R/W
Read
LBA
OE
EB (EBC=0)
EB (EBC=1)
ECB
DATA_IN
V1 Word
V2 Word
V3 Word
V4 Word
Figure 65. WSC = 2, SYNC = 1, DOL = [1/0], A.WORD/E.WORD
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
75
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[2]
htrans
Nonseq
Seq
Idle
hwrite
haddr
Read
V1
Read
V2
hready
weim_hrdata
Last Valid Data
V1 Word
V2 Word
weim_hready
BCLK
A[24:0]
CS[2]
R/W
Last Valid Addr
Address V1
Address V2
Read
LBA
OE
EB (EBC=0)
EB (EBC=1)
ECB
DATA_IN
V1 1/2
V1 2/2
V2 1/2
V2 2/2
Figure 66. WSC = 2, SYNC = 1, DOL = [1/0], A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
76
Freescale Semiconductor
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[2]
Non
htrans
Seq
Read
V2
Idle
seq
Read
V1
hwrite
haddr
hready
weim_hrdata
Last Valid Data
V1 Word
V2 Word
weim_hready
BCLK
Last Valid
Addr
Address V1
A[24:0]
CS[2]
Read
R/W
LBA
OE
EB (EBC=0)
EB (EBC=1)
ECB
DATA_IN
V1 1/2
V1 2/2
V2 1/2
V2 2/2
Figure 67. WSC = 7, OEA = 8, SYNC = 1, DOL = 1, BCD = 1, BCS = 2, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
77
Specifications
Note: Signals listed with lower case letters are internal to the device.
hclk
hselm_weim_cs[2]
htrans
Non
seq
Seq
Idle
hwrite
haddr
Read
V1
Read
V2
hready
weim_hrdata
Last Valid Data
V1 Word
V2 Word
weim_hready
BCLK
A[24:0]
CS[2]
Last Valid
Addr
Address V1
R/W
LBA
Read
OE
EB (EBC=0)
EB (EBC=1)
ECB
DATA_IN
V1 1/2
V1 2/2
V2 1/2
V2 2/2
Figure 68. WSC = 7, OEA = 8, SYNC = 1, DOL = 1, BCD = 1, BCS = 1, A.WORD/E.HALF
MC9328MX21S Technical Data, Rev. 1.3
78
Freescale Semiconductor
Specifications
3.19 DTACK Mode Memory Access Timing Diagrams
When enabled, the DTACK input signal is used to externally terminate a data transfer. For DTACK
enabled operations, a bus time-out monitor generates a bus error when an external bus cycle is not
terminated by the DTACK input signal after 1024 HCLK clock cycles have elapsed, where HCLK is the
internal system clock driven from the PLL module. For a 133 MHz HCLK setting, this time equates to
7.7 μs. Refer to the Section 3.5, “DPLL Timing Specifications” for more information on how to generate
different HCLK frequencies.
There are two modes of operation for the DTACK input signal: rising edge detection or level sensitive
detection with a programmable insensitivity time. DTACK is only used during external asynchronous data
transfers, thus the SYNC bit in the chip select control registers must be cleared.
During edge detection mode, the EIM will terminate an external data transfer following the detection of
the DTACK signal’s rising edge, so long as it occurs within the 1024 HCLK cycle time. Edge detection
mode is used for devices that follow the PCMCIA standard. Note that DTACK rising edge detection mode
can only be used for CS[5] operations. To configure CS[5] for DTACK rising edge detection, the following
bits must be programmed in the Chip Select 5 Control Register and EIM Configuration Register:
•
•
WSC bit field set to 0x3F and CSA (or CSN) set to 1 or greater in the Chip Select 5 Control Register
AGE bit set in the EIM Configuration Register
Other bits such as DSZ, OEA, OEN, and so on, may be set according to system and timing requirements
of the external device. The requirement of setting CSA or CSN is required to allow the EIM to wait for the
rising edge of DTACK during back-to-back external transfers, such as during DMA transfers or an internal
32-bit access through an external 16-bit data port.
During level sensitive detection, the EIM will first hold off sampling the DTACK signal for at least 2
HCLK cycles, and up to 5 HCLK cycles as programmed by the DCT bits in the Chip Select Control
Register. After this insensitivity time, the EIM will sample DTACK and if it detects that DTACK is logic
high, it will continue the data transfer at the programmed number of wait states. However, if the EIM
detects that DTACK is logic low, it will wait until DTACK goes to logic high to continue the access, so
long as this occurs within the 1024 HCLK cycle time. If at anytime during an external data transfer
DTACK goes to logic low, the EIM will wait until DTACK returns to logic high to resume the data transfer.
Level detection is often used for asynchronous devices such graphic controller chips. Level detection may
be used with any chip select except CS[4] as it is multiplexed with the DTACK signal. To configure a chip
select for DTACK level sensitive detection, the following bits must be programmed in the Chip Select
Control Register and EIM Configuration Register:
•
•
EW bit set, WSC set to > 1, and CSN set to < 3 in the Chip Select Control Register
BCD/DCT set to desired “insensitivity time” in the Chip Select Control Register. The “insensitivity time”
is dictated by the external device’s timing requirements.
•
AGE bit cleared in the EIM Configuration Register
Other bits such as DSZ, OEA, OEN, and so on, may be set according to system and timing requirements
of the external device.
The waveforms in the following section provide examples of the DTACK signal operation.
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
79
Specifications
3.19.1 DTACK Example Waveforms: Internal ARM AHB Word Accesses to
Word-Width (32-bit) Memory
HCLK
BCLK
Last Valid
Addr
V1
ADDR
CS[5]
Read
RW
LBA
OE
EB (EBC=0)
EB (EBC=1)
DTACK
DATA_IN
V1 Data
Figure 69. DTACK Edge Triggered Read Access, WSC=3F, OEA=8, OEN=5, AGE=1.
MC9328MX21S Technical Data, Rev. 1.3
80
Freescale Semiconductor
Specifications
HCLK
BCLK
Last Valid Addr
Address V1
V1+8
V1+4
ADDR
CS[0]
Read
RW
LBA
OE
EB (EBC=0)
EB (EBC=1)
DCT
DTACK
DATA_IN
V1 Word
V1+4 Word
V1+8 Word
Figure 70. DTACK Level Sensitive Sequential Read Accesses, WSC=2, EW=1, DCT=1, AGE=0 (Example of
DTACK Remaining High)
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
81
Specifications
HCLK
BCLK
ADDR
CS[0]
Address V1
V1+4
V1+8
Last Valid Addr
RWA
RWN
Write
RW
LBA
OE
EB
DCT
DTACK
V1 Word
V1+4 Word
V1+8
DATA_OUT
Figure 71. DTACK Level Sensitive Sequential Write Accesses, WSC=2, EW=1, RWA=1, RWN=1, DCT=1,
AGE=0 (Example of DTACK Asserting)
MC9328MX21S Technical Data, Rev. 1.3
82
Freescale Semiconductor
Specifications
2
3.20 I C Module
2
The I C communication protocol consists of seven elements: START, Data Source/Recipient, Data
Direction, Slave Acknowledge, Data, Data Acknowledge, and STOP.
SDA
3
4
5
SCL
1
6
2
2
Figure 72. Definition of Bus Timing for I C
2
Table 39. I C Bus Timing Parameters
1.8 V 0.1 V
3.0 V 0.3 V
Ref
No.
Parameter
Unit
Minimum
Maximum
Minimum
Maximum
SCL Clock Frequency
0
100
–
0
100
–
kHz
ns
ns
ns
ns
ns
ns
1
2
3
4
5
6
Hold time (repeated) START condition
Data hold time
114.8
0
111.1
0
69.7
–
72.3
–
Data setup time
3.1
1.76
68.3
335.1
111.1
HIGH period of the SCL clock
LOW period of the SCL clock
Setup time for STOP condition
69.7
336.4
110.5
–
–
–
–
–
–
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
83
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not available from
Freescale for import or sale in the United States prior to September 2010: i.MX21 Product Family
4 Pin Assignment and Package Information
Table 40. i.MX21S Pin Assignment
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
OE_
ACD
USBH1_ USBH1_ USBG_
SAP_
TXDAT
SSI1_
CLK
SSI2_
RXDAT
SSI3_
FS
A
B
C
D
E
F
LD9
LD12
LD14
REV HSYNC
SD2_D2 PB10
PB16
PB20
TOUT
SSI2_TXDAT
FS
OE
USBG_ USBG_
SCL TXDM
USBH1_ USBG_
RXDM RXDM
FS
CON
TRAST
SD2_
SD2_D0
USB_
PWR
SAP_
FS
SSI1_
FS
SSI2_
FS
SSI3_
TXDAT
CSPI2_
SS2
LD7
LD1
LD2
LD8
LD5
LD3
LD0
LD4
D31
D29
D27
A18
LD11
LD6
LD16
LD10
CLS
PS
PB14
PB15
PB12
PB18
PB21
PB19
I2C_DATA
I2C_CLK
CSPI2_SS0
CSPI1_SS2
KP_ROW0
PE3
CMD
USB_
OC
SSI1_
TXDAT
SSI3_
RXDAT
SSI3_
CLK
CSPI2_
SS1
LD17 VSYNC SD2_D3 PB11
TIN
SD2_
CLK
USBH1_ USBH1_ USBG_ USBG_
SAP_
RXDAT RXDAT
SSI1_
SSI2_
CLK
CSPI2_
SCLK
LD13
LD15
QVDD
QVSS SD2_D1
TXDM
RXDP
ON
RXDP
SPL_
SPR
SAP_
CLK
CSPI2_
MISO
CSPI2_
MOSI
A24_
NFIO14
A25_
NFIO15
CSPI1_
SS1
CSPI1_
MISO
CSPI1_
SS0
LSCLK
D30
D28
D26
D24
D22
D18
D16
D14
D12
D10
OE
A22_
NFIO12
A23_
NFIO13
USB_
BYP
USBH_ USBG_ USBG_
ON SDA TXDP
KP_
ROW1
KP_
ROW3
KP_
ROW4
G
H
J
NVDD6 NVSS6
NVDD1 NVSS5
PB13
PB17
A21_
NFIO11
CSPI1_ CSPI1_ USBH1_ USBG_
TEST_
WB4
TEST_
WB2
A20
A19
TEST_WB3
KP_COL0
KP_COL4
UART3_CTS
UART1_RTS
SD1_D1
PWMO
SCLK
RDY
TXDP
OE
KP_
ROW5
KP_
ROW2
CSPI1_ TEST_
TEST_
WB1
D25
D23
D21
D20
D17
D15
D13
EB3
EB2
D9
NVDD1 NVDD5 NVDD4
NVSS1 NVSS4 QVDDX
NVSS1 NVDD3 QVDD
NVDD2 NVDD3 NVSS3
PE4
KP_COL1
KP_COL5
MOSI
WB0
UART1_
RXD
KP_
COL3
KP_
COL2
K
L
A16
A17
TDO
QVDD
QVSS
A14_
NFIO9 NFIO10
A15_
UART1_
TXD
UART3_
RTS
UART3_
TXD
QVSS
QVSS
NFIO2
NFIO7
NFWP
NFRB
PE6
PE7
A13_
D19
EXT_
48M
UART3_
RXD
UART1_
CTS
M
N
P
R
T
NFIO8
SD1_
D0
A11
A9
A12
A10
A8
LBA
NVSS3 SDCKE0 NVSS1 NVSS1 NVDD1 NVDD1
TCK
RTCK
TMS
SD1_
D2
SD1_
CMD
TDI
SD1_
CLK
EXT_
266M
A7
NVSS2
TRST
RESET_
IN
CLK
MODE0
A5
A6
CS3
CS4
CS5
CS2
CS1
D6
BCLK
ECB
CS0
D4
MA11
D3
RAS
MA10
D1
CAS
NFIO5
PF16
NFIO3
NFIO4
CLKO
NFWE
NFIO1
NFIO6
NFRE
NFCE
BOOT1
POR
SD1_D3 CLKMODE1
PC_
PWRON
U
V
W
D11
A4
EB1
EB0
A2
NFALE
QVSS
QVDD
NFCLE
BOOT2
BOOT3
VDDA
QVDD
XTAL32K
JTAG_
CTRL
RESET_
OUT
OSC26M_
TEST
EXTAL
32K
D8
D5
RW
D2
SDWE
BOOT0
EXTAL
26M
A3
D7
A1
A0
D0
SDCLK SDCKE1 NFIO0
QVSS
XTAL26M
QVSS
Pin Assignment and Package Information
4.1
MAPBGA Package Dimensions
Figure 73 illustrates the MAPBGA 14 mm × 14 mm × 1.41 mm package, which has 0.65 mm ball pitch.
Figure 73. i.MX21 MAPBGA Mechanical Drawing
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
85
Pin Assignment and Package Information
4.2
MAPBGA Package Dimensions
Figure 74 illustrates the MAPBGA 17 mm × 17 mm × 1.45 mm package, which has 0.8 mm spacing
between the pads.
Figure 74. i.MX21 MAPBGA Mechanical Drawing
MC9328MX21S Technical Data, Rev. 1.3
86
Freescale Semiconductor
Document Revision History
5 Document Revision History
Table 41 provides the document changes for the MC9328MX21S Rev. 1.3.
Table 41. Document Revision History
Location
Description of Change
Table 1 on page 3
Table 7 on page 14
Table 40 on page 84
Added VM and CVM devices.
Updated Sleep Current values..
Added Package Drawing for the 17mm x 17mm package.
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
87
How to Reach Us:
Information in this document is provided solely to enable system and software implementers to use
Freescale Semiconductor products. There are no express or implied copyright licenses granted
hereunder to design or fabricate any integrated circuits or integrated circuits based on the information
in this document.
Home Page:
www.freescale.com
E-mail:
Freescale Semiconductor reserves the right to make changes without further notice to any products
herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the
suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any
and all liability, including without limitation consequential or incidental damages. “Typical” parameters
that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating parameters,
including “Typicals”, must be validated for each customer application by customer’s technical experts.
Freescale Semiconductor does not convey any license under its patent rights nor the rights of others.
Freescale Semiconductor products are not designed, intended, or authorized for use as components
in systems intended for surgical implant into the body, or other applications intended to support or
sustain life, or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer purchase or use
Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall
indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney
fees arising out of, directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was
negligent regarding the design or manufacture of the part.
support@freescale.com
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
support@freescale.com
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
support@freescale.com
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064, Japan
0120 191014 or +81 3 5437 9125
support.japan@freescale.com
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. ARM, Multi-
ICE, and the ARM Powered logo are registered trademarks of ARM Limited. ARM926EJ-S is a
trademark of ARM Limited. All other product or service names are the property of their respective
owners.
Asia/Pacific:
© Freescale Semiconductor, Inc. 2005–2008. All rights reserved.
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
support.asia@freescale.com
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-521-6274 or 303-675-2140
Fax: 303-675-2150
LDCForFreescaleSemiconductor@hibbertgroup.com
Document Number: MC9328MX21S
Rev. 1.3
06/2008
相关型号:
MC9328MX21SVKR2
32-BIT, 266 MHz, MICROPROCESSOR, PBGA289, 14 X 14 MM, 1.41 MM HEIGHT, 0.65 MM PITCH, LEAD FREE, MAPBGA-289
NXP
MC9328MX21SVMR2
32-BIT, 266MHz, MICROPROCESSOR, PBGA289, 17 X17 MM, 1.45 MM HEIGHT, 0.80 MM PITCH, LEAD FREE, MAPBGA-289
NXP
©2020 ICPDF网 联系我们和版权申明