AU5783D,518 [NXP]
IC SPECIALTY INTERFACE CIRCUIT, PDSO14, 3.90 MM, PLASTIC, SO-14, Interface IC:Other;
| 型号： | AU5783D,518 |
| 厂家： | 
NXP |
| 描述： | IC SPECIALTY INTERFACE CIRCUIT, PDSO14, 3.90 MM, PLASTIC, SO-14, Interface IC:Other 光电二极管 接口集成电路 |
| 文件： | 总14页 (文件大小：91K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
AU5783
J1850/VPW transceiver with
supply control function
Preliminary specification
2001 Feb 15
Supersedes data of 2000 Nov 29
Philips
Semiconductors
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
FEATURES
DESCRIPTION
The AU5783 is a line transceiver being primarily intended for
in-vehicle multiplex applications. It provides interfacing between a
J1850 link controller and the physical bus wire. The device supports
the SAE/J1850 VPWM standard with a nominal bus speed of
10.4 kbit/s. For data upload and download purposes the 4X
transmission mode is supported with a nominal bus speed of
41.6 kbit/s. The AU5783 provides protection against loss of ground
conditions, thus ensuring the network will be operational in case of
an electronic control unit loosing connection to ground potential. Low
power operation is supported through provision of a sleep mode with
very low power consumption. In addition an external voltage
regulator can be turned off via the AU5783 transceiver to further
reduce the overall power consumption. The voltage regulator will be
activated again upon detection of bus activity or upon a local
wake-up event.
• Supports SAE/J1850 VPW standard for in-vehicle class B
multiplexing
• Bus speed 10.4 kbit/s nominal
• 4X transmission mode (41.6 kbit/s)
• Drive capability 32 bus nodes
• Low RFI due to output waveshape function
• Direct battery operation with protection against +40 V load dump
and 8 kV ESD
• Bus terminals proof against automotive transients up to
+100 V/–150 V and 8 kV ESD
• Power supply enable function
• Very low sleep mode power consumption
• Diagnostic loop-back mode
• Thermal overload protection
• 14-pin SOIC
ORDERING INFORMATION
PACKAGE
DESCRIPTION
plastic small outline package; 14 leads; body width 3.9 mm
TEMPERATURE
RANGE
TYPE NUMBER
NAME
VERSION
AU5783D
SO14
SOT108-1
–40 to +125°C
QUICK REFERENCE DATA
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
V
BAT.op
Operating supply voltage, including low battery
operation
5.5
12
16
V
T
Operating ambient temperature range
Battery voltage
–40
+125
+40
8.0
4.2
90
°C
V
amb
V
load dump, 1s
BAT.ld
V
V
Bus output voltage
250 Ω < R < 1.6 kΩ
6.7
3.4
V
BOH
L
Bus input threshold
V
BI
I
t
t
Sleep mode supply current
Propagation delay
µA
µs
µs
BAT.lp
Tx to Rx
25
P
r
Bus output rise time
14
2
2001 Feb 15
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
BLOCK DIAGRAM
BATTERY (+12V)
BAT
VOLTAGE
TEMP.
R/F
REFERENCE
PROTECTION
Rs
TX–
OUTPUT
BUFFER
TX
BUS
BUFFER
NSTB
MODE
Rld
CONTROL
4X/LOOP
Vcc (+5V)
1.6V
Rd
LOAD
LOAD
SWITCH
RX
VOLTAGE
REFERENCE
Vbat
INH
WAKE-UP
CONTROL
AU5783
LWAKE
GND
SL01224
Figure 1. Block diagram
3
2001 Feb 15
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
PINNING
Pin configuration
FUNCTIONAL DESCRIPTION
The AU5783 is an integrated line transceiver IC that interfaces an
SAE/J1850 protocol controller IC to the vehicle’s multiplex bus line.
It is primarily intended for automotive “Class B” multiplexing
applications in passenger cars using VPW (Variable Pulse Width)
modulated signals with a nominal transmission speed of 10.4 kbit/s.
The device provides transmit and receive capability as well as
protection to a J1850 electronic module.
1
14
13
12
11
10
9
GND
N.C.
R/F
2
3
4
5
6
7
GND
4X/LOOP
NSTB
TX
BUS
A J1850 link controller feeds the transmit data stream to the
transceiver’s TX input. The AU5783 transceiver waveshapes the TX
data input signal so as to minimize electromagnetic emission. The
bus output signal features controlled rise & fall characteristic
including rounded shape. A resistance being connected to the R/F
control input sets the bus output slew rate.
LOAD
INH
AU5783
LWAKE
BAT
RX
The LOAD output is connected to the physical bus line via an
N.C.
8
external load resistor R . The load resistor pulls the bus line to
ld
SO14
ground potential being the default state, e.g., when no transmitter
outputs an active state. This output ensures the J1850 network will
not be affected by a potential loss of ground condition at an
individual electronic control unit.
SL01225
Figure 2. Pin configuration
The AU5783 includes a bus receiver with filter function to minimize
susceptibility against interference. The logic state of the J1850 bus
signal is indicated at the RX output being connected to the J1850
link controller.
Pin description
SYMBOL PIN
DESCRIPTION
The AU5783 also provides advanced low-power modes to help
minimize ignition-off power consumption of an electronic control unit.
The bus receiver function is kept alive in the low-power modes. If an
active state is being detected on the bus line this will be indicated
via the RX output. By default the AU5783 enters the low-power
standby mode when the mode control inputs NSTB and 4X/LOOP
are not driven. A 100 kΩ pull down resistor is required on NSTB.
R/F
1
Rise/fall time control input; connect to ground
potential via a resistor
GND
2
3
Ground
4X/LOOP
Tx mode control input; low: normal mode;
high: 4X mode; float: loopback
NSTB
4
Network STandBy power control input; low:
transmit function disabled (low power modes);
high: transmit function enabled
Ignition-off current draw can be reduced further by turning off the
voltage regulator being typically provided in an electronic control
unit. This is supported by the activity indication function of the
AU5783. In this application the activity indication flag INH will control
external devices such as a voltage regulator. To turn-off the INH flag
and thus the voltage regulator, the go to sleep command needs to
be applied to the Network Standby power control input,
e.g., NSTB = 0. The INH output is turned off after the sleep time-out
period thereby, reducing the power consumption of an electronic
control unit to an extremely low level.
TX
RX
5
6
Transmit data input; low: transmitter passive;
high: transmitter active
Receive data output; low: active bus condition
detected; high: otherwise
N.C.
7
8
9
Not connected
BAT
Battery supply input, 12V nominal
Local wake-up input, edge sensitive
LWAKE
INH
10 Activity indication flag (inhibit) output high side
driver; e.g., to control a voltage regulator.
Active high enables the regulator
The activity indication flag INH will be turned on again upon
detection of a remote wake-up condition (i.e. bus activity) or upon
detection of a local wake-up condition or a respective command
from the microcontroller. A local wake-up condition is detected
when an edge occurs at the wake-up input LWAKE. The INH flag
will also be turned on upon detection of a high input level at the
mode control input NSTB. Activation of the INH output enables
external devices, e.g., a voltage regulator. This condition will power-up
logic devices, e.g., a microcontroller in order to perform appropriate
action, e.g., activation of the AU5783 and the J1850 network.
LOAD
BUS
11 Bus load in/output
12 Bus line transmit/receive input/output, active
high side driver
N.C.
13 Not connected
14 Ground
GND
The AU5783 contain a power on reset (POR) circuit, which is active
at low voltages. This circuit insures that if the control input NSTB is
at 0 V or floating during power up, the device will be forced into the
standby mode by the time the battery voltage rises to 4.4 V. This will
also insure that the INH pin is in the high state to turn on the local
voltage regulator. If there is a dip going below 4.4 V in battery
voltage while in the sleep mode, the device may return to the
4
2001 Feb 15
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
standby mode if the POR is tripped. Even if the device is not in
sleep mode the INH output will turn off at some battery voltages
below 4.4 V when the internal POR circuit is active. At still lower
voltages where the POR circuit does not operate, the INH may
again pull up toward the battery level, typically with battery voltages
below approximately 3.6 V. The operation of the POR circuit can be
verified by placing the device in the sleep mode while the battery
voltage is above 4.4 V. The INH output, which is a high side driver,
should turn off when the sleep mode is entered. Next ramp the
battery voltage down to 2.0V and finally return the battery voltage to
4.4 V. When the battery supply is returned to 4.4V, the INH output
will pull high since the device enters standby mode. The actual
voltages at which the POR engages and releases will vary from part
to part. The lowest voltage at which the POR will be active is 2.6 V
and it will always release below 4.4 V.
essentially disconnecting an electronic control unit from the J1850
bus line. The TX signal is internally looped back to the RX output.
The AU5783 only requires one power supply V . Bus
BAT
transmissions can continue with battery voltage down to 5.5 V. The
bus output voltage will track 1.3V bellow the battery voltage. The
bus input voltage threshold will also follow the battery voltage going
down as shown in Figure 3. This ratio metric behavior of the input
threshold partially compensates for the reduced dominant level
transmitted during low battery operation.
The AU5783 features special robustness at its BAT and BUS pins
hence the device is well protected for applications in the automotive
environment. Specifically the BAT input is protected against 40 V
load dump and jump start condition. The BUS output is protected
against wiring fault conditions, e.g., short circuit to ground and
battery voltage as well as typical automotive transients and
electrostatic discharge. In addition, an over-temperature shutdown
function with hysteresis is incorporated which protects the device
under network fault conditions. In case of the die temperature
reaching the trip point, the AU5783 will latch-off the transceiver
function. The device is reset on the first rising edge on the TX input
after a decrease in the junction temperature.
The AU5783 provides a high-speed data transmission mode where
the bus output waveshape function is disabled. In this mode transmit
signals are output as fast as possible thus allowing higher data
rates, e.g., the so-called 4X mode with 41.6 kbit/s nominal speed.
The AU5783 also provides a loop-back mode for diagnostic
purpose, e.g., self-test of an electronic control unit. In loop-back
mode the bus transmit and receive functions are disabled thus
8
6.7
5.5
4.2
bus output
bus input
3.9
3.4
1.9
5.5 5.8
7
8
16
SL01254
Battery Voltage (V)
Figure 3. Bus voltage vs battery voltage
5
2001 Feb 15
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
Table 1. Control input summary
Z = Input connected to high impedance permitting it to float. Typically accomplished by turning off the output of a microcontroller.
X = Don’t care; The input may be at either logic level.
NSTB
4X/LOOP
TX
Mode
Bus
transmitter
BUS
RX (out)
INH
1
1
0
0
1
0
normal operation
normal operation
active
high
float
low
high
high
passive
bus state,
Note 2
1
1
1
1
1
0
4X transmit
4X transmit
active
high
float
low
high
high
passive
bus state,
Note 2
1
1
Z
Z
X
1
0
loop-back
loop-back
passive
passive
off
float
float
float
low
high
high
high
high
0 or Z
X
standby (default state after power on),
Note 1, Note 6
bus state,
Note 5
1 –> 0
0 or Z
X
X
0
go to sleep command, Note 4, Note 6
off
off
float
float
bus state,
Note 5
float, Note 3
float
X
sleep, Note 4, Note 6
bus state,
Note 5
NOTES:
1. After power-on, the AU5783 enters standby mode since the input pins NSTB and 4X/LOOP are assumed to be floating. In standby mode the
voltage regulator is enabled via the INH output, and therefore power is supplied to the microcontroller. When the microcontroller begins
operation it will normally set the control inputs NSTB high and 4X/LOOP to low state in order to start normal operation of the AU5783.
2. RX outputs the bus state. If the bus level is below the receiver threshold (i.e., all transmitters passive), then RX will be high. Otherwise, if the
bus level is above the receiver threshold (i.e., at least one transmitter is active), then RX will be low.
3. INH is turned off after a time-out period.
4. For entering the sleep mode (e.g., to deactivate INH), the “Go To Sleep” command needs to be applied. The “Go To Sleep” command is a
high-to-low transition on the NSTB input. When the “Go To Sleep” command is present, the INH flag is deactivated. This signal can be used
to turn-off the voltage regulator of an electronic module. After the voltage regulator is turned off the microcontroller is no longer supplied and
the NSTB input will be floating. The INH output will be set again upon detection of bus activity or occurrence of a local wake-up event.
5. In standby and sleep mode, the detection of a wake-up condition (e.g., high level on BUS) will be signalled on the output RX.
6. The NSTB pin contains a weak pull down which is active in the normal, loop-back and high-speed modes but is disabled in the sleep mode.
To insure a logic 0 input if the microcontroller’s outputs are tri-stated or the microcontroller is not powered, a 100 kΩ resistor between NSTB
and ground is suggested.
6
2001 Feb 15
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
ABSOLUTE MAXIMUM RATINGS
According to the IEC 134 Absolute Maximum System.
Unless otherwise specified, operation is not guaranteed under these conditions: all voltages are referenced to pin GND; positive currents flow
into the IC.
SYMBOL
PARAMETER
Voltage on pin BAT
CONDITIONS
MIN.
–0.3
MAX.
+34
UNIT
V
BAT
V
V
Short-term supply voltage
load dump, t < 1s
+40
V
V
BAT.ld
BAT.tr
V
Transient voltage on pin BAT and pin
LWAKE
SAE J1113 test pulses 3A and 3B,
Rwake > 9 kΩ
–150
+100
V
B0
V
B1
V
B.tr
Bus voltage
V
< 2 V, R > 1.4 kΩ
–16
+18
V
V
V
BAT
BAT
ld
Bus voltage
V
> 2 V, R > 1.4 kΩ
–10
+18
ld
Transient bus voltage
SAE J1113, test pulses 3A and 3B,
coupled via C = 1 nF; R > 1.4 kΩ
–150
+100
ld
V
WKE
V
WKR
V
INH
V
I
Voltage on pin LWAKE
Voltage on pin LWAKE
DC voltage on pin INH
–0.3
–16
≤ V
V
V
V
V
BAT
via series resistor of Rwake > 9 kΩ
+34
–0.3
–0.3
≤ V
BAT
DC voltage on pins TX, RX, NSTB and
4X/LOOP
7.0
V
DC voltage on pin R/F
–0.3
–8
5.0
+8
V
I,RF
ESD
ESD capability of pins BAT, BUS, LOAD
and LWAKE
Human body model, direct contact
discharge, R = 1.5 kΩ, C = 100 pF,
kV
HBM1
R
> 1.4 kΩ; Rwake > 9 kΩ
ld
ESD
ESD capability of all pins
Human body model, direct contact
discharge, R = 1.5 kΩ, C = 100 pF
–2
+2
kV
HBM2
P
Maximum power dissipation
Thermal impedance
@ T
= +125°C
205
mW
°C/W
°C
tot
amb
Θ
with standard test PCB
120
JA
T
amb
Operating ambient temperature
Operating junction temperature
Storage temperature
–40
–40
–40
+125
+150
+150
T
vj
°C
T
stg
°C
7
2001 Feb 15
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
DC ELECTRICAL CHARACTERISTICS
7V < V
< 16 V; –40 °C < T < +125 °C; 250 Ω < R < 1.6 kΩ; 1.4 kΩ < R < 12 kΩ;
amb L ld
BAT
–2V < V
< +9 V; NSTB = 5 V; 4X/LOOP = 5 V; R = 56 kΩ ± 1%; RX connected to +5 V via R = 3.9 kΩ; INH loaded with 100 kΩ to GND;
bus
s
d
LWAKE connected to BAT via 10 kΩ resistor; all voltages are referenced to pin 14 (GND); positive currents flow into the IC;
typical values reflect the approximate average value at V = 13 V and T = 25 °C; unless otherwise specified.
BAT
amb
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Pin BAT & thermal shutdown
I
I
I
Sleep mode supply current
Standby mode supply current
Note 1
Note 1
90
µA
µA
mA
BAT.sl
500
3
BAT.sb
BAT.p.nl
Supply current; passive state, in normal or
loopback modes
TX = 5 V; LWAKE = 0 V,
4X/LOOP = 0 or Z
I
Supply current; passive state, in high
speed mode
TX = 5 V; LWAKE = 0 V,
4X/LOOP = 5 V
10
mA
BAT.p.h
I
I
Supply current; weak load
Supply current; full load
TX = 5 V, R = 1.38 kΩ, Note 2
25
mA
mA
°C
BAT.wl
L
TX = 5 V, R = 250 Ω
45
BAT.fl
L
T
Thermal shutdown temperature
Thermal shutdown hysteresis
Note 2
Note 2
155
190
15
sd
T
5
°C
hys
Pins TX, NSTB
V
V
High level input voltage
Low level input voltage
TX high level input current
2.7
V
ih
0.9
200
50
V
il
I
I
V
V
= 5 V
50
10
µA
µA
ihtx
TX
NSTB high level input current in normal,
loop back and high speed modes
= 5 V
ih.nstb,nlh
NSTB
I
il
Low level input current
V = 0 V
i
–2
+2
µA
Pin 4X/LOOP
V
High level input voltage (High Speed
Mode)
NSTB = 5 V
2.7
2.9
50
V
ih
NSTB = 5 V, Bare Die
4X/LOOP = 5 V, NSTB = 5 V
4X/LOOP = 3 V, NSTB = 3 V
NSTB = 5 V
V
I
I
High level input current with 5 V logic
High level input current with 3 V logic
300
250
1.65
µA
µA
V
ih-5
30
ih-3
V
ilb
Mid level input voltage (Loop back
operation)
1.25
I
Loopback mode input current
Low level input voltage (Normal Mode)
Low level input current
NSTB = 5 V; Note 4
NSTB = 5 V
–2
2
µA
V
ilb
V
+0.7
200
+5
il
–I
–I
V
4X
V
4X
= 0 V, NSTB = 5 V
= 0 V, NSTB = 0 V
50
–5
µA
µA
il
Low level input current in standby and
sleep mode
ils
Pin LWAKE
V
V
Local wake-up high
Local wake-up low
Low level input current
NSTB = 0 V
NSTB = 0 V
3.9
2
V
i_wh
i_Wl
2.5
25
V
–I
V
= 0 V
µA
I_w
LWAKE
Pin INH
–I
INH high level output current
INH off-state output leakage
V
= V
– 1 V;
BAT
120
–5
500
µA
oh_inh
INH
4.9 V < V
< 16 V
BAT
–I
ol_inh
V
INH
= 0 V; NSTB = 0 V
+5
µA
V
Power-on reset release voltage; Battery
voltage threshold for setting INH output
high
NSTB = 0 V, BUS = 0 V,
= 4.4 V, verify INH = 1
4.4
V
bat_POR
V
BAT
Pin RX
V
ol_rx
Low level output voltage
I
= 1.6 mA, BUS = 7 V,
0
0.45
V
RX
all modes
I
I
Low level output current
High level output leakage
V
RX
V
RX
= 5 V, BUS = 7 V
2
20
mA
ol_rx
= 5 V, BUS = 0 V, all modes
–10
+10
µA
oh_rx
8
2001 Feb 15
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
SYMBOL
Pin BUS
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
8.0
UNIT
V
BOh_n
V
BOh_h
V
BOhl
BUS output high voltage in normal mode
TX = 5 V, 4X/LOOP = 0 V;
6.7
6.7
V
8 V < V
< 16 V
BAT
250 Ω < R < 1.6 kΩ; Note 3
L
BUS output high voltage in high speed
mode
TX = 5 V, 4X/LOOP = 5 V;
9.0
V
V
8 V < V
< 16 V
BAT
250 Ω < R < 1.6 kΩ; Note 3
L
BUS voltage; low battery
TX = 5 V; Note 3
V
–1.3
BAT
V
BAT
5.5 V<V
< 8 V;
BAT
250 Ω < R < 1.6 kΩ
L
–I
–I
BUS short circuit current
TX = 5 V; V
= –2 V
BUS
30
100
mA
BO.LIM
BUS leakage current; passive state
TX = 0 V; 0 V < V
< 16 V;
–100
–100
–100
+100
µA
BO.LK1
BAT
< +9 V
–2 V < V
BUS
–I
BO.LK0
–I
BO.LK5
,
BUS current with loss of battery
V
BAT
< 2 V; –2 V < V < +9 V
BUS
+100
+100
+100
µA
µA
–I
–I
,
BUS leakage current; loop back mode
TX = 0 V or 5 V; 0 V<V
<16 V;
BAT
BO.LKLB0
BO.LKLB5
–2 V < V
< +9 V
BUS
–I
BUS leakage current at loss of ground
BUS input high voltage
0 V < V
< 16 V; see test circuit
–20
4.2
µA
LOG
Bih
BAT
V
5.8 V < V
< 16 V,
V
BAT
4X/LOOP = 5 V and
4X/LOOP = 0 V
V
V
V
BUS input low voltage
4X/LOOP = 5 V or
4X/LOOP = 0 V
3.4
0.5
V
V
V
Bil
BUS input hysteresis
4X/LOOP = 5 V and
4X/LOOP = 0 V
0.1
Bhy
Bih_l
BUS input high voltage at low battery
5.5 V < V
< 5.8 V,
V
BAT
–
BAT
4X/LOOP = 5 V and
4X/LOOP = 0 V
1.6 V
V
BiL_L
V
Bih_s
BUS input low voltage at low battery
5.5 V < V
4X/LOOP = 5 V and
4X/LOOP = 0 V
< 7 V,
V
BAT
3.6 V
–
V
V
BAT
BUS input high voltage in standby and
sleep mode
NSTB = 0 V,
4X/LOOP = 5 V and
4X/LOOP = 0 V,
4.2
6 V < V
< 16 V
BAT
V
V
V
BUS input low voltage in standby
and sleep mode
NSTB = 0 V,
4X/LOOP = 5 V and
4X/LOOP = 0 V,
2.2
V
V
V
Bil_s
6 V < V
< 16 V
BAT
1
BUS input high voltage in standby and
sleep mode at low battery
NSTB = 0 V,
4X/LOOP = 5 V and
4X/LOOP = 0 V ,
/ (V
+
BAT
Bih_sl
Bil_sl
2
2.4)
4.5 V < V
< 6 V
BAT
1
BUS input low voltage in standby and
sleep mode at low battery
NSTB = 0 V,
4X/LOOP = 5 V and
4X/LOOP = 0 V ,
/ (V
2
–
BAT
1.6)
4.5 V < V
< 6 V
BAT
Pin LOAD
V
V
Load output voltage
Il = 2 mA
0.2
1
V
V
ld
d
Load output voltage unpowered
I
ld
= 6 mA, V
= 0 V
BAT
ldoff
NOTES:
1. TX = 0 V; NSTB = 0 V; 7 V < V
< 13 V; T < 125°C; –1 V < V < 1 V; LWAKE connected to BAT via 10 kΩ; INH not connected.
BUS
BAT
j
2. This parameter is characterized but not subject to production test.
3. For V < 8.3 V the bus output voltage is limited by the supply voltage.
BAT
For 16 V < V
< 27 V the load is limited by the package power dissipation ratings. The duration of the latter condition is recommended
BAT
to be less than 2 minutes.
4. For 3-State devices driving the 4X/LOOP Pin, the leakage in the 3-State output must be below the specified input current to ensure the pin is
biased in the center state to provide the loop back function. For 3-State devices driving the 4X/LOOP pin, the leakage in the 3-State output
must be below the specified input current to insure the pin is biased in the center state to provide the loop back function. If the leakage
current of the microcontroller is too high, then an alternate approach is to connect a resistor voltage divider between the V and ground of
CC
the microcontroller’s supply to provide approximately 1.45 V bias on the 4X/LOOP pin.
9
2001 Feb 15
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
DYNAMIC CHARACTERISTICS
7 V < V
< 16 V; –40°C < T
< +125°C; –2 V < V
< +9 V; 1.4 kΩ < R < 12 kΩ
bus ld
BAT
amb
BUS: 250 Ω < R < 1.6 kΩ; 3 nF < C < 17 nF; 1.7 µs < (R * C ) < 5.2 µs
L
L
L
L
Bus load A: R = 1.38 kΩ, C = 3.3 nF; Bus load B: R = 300 Ω, C = 16.5 nF
L
L
L
L
R/F pin: R = 56 kΩ ± 1%; INH loaded with 100 kΩ and 30 pF to GND
s
RX pin: R = 3.9 kΩ to 5 V; C = 30 pF to GND; NSTB = 5 V; 4X/LOOP = 0 V
d
L
Typical values reflect the approximate average value at V
NSTB and 4X/LOOP rise and fall times < 10 ns.
= 13 V and T
= 25°C, unless otherwise specified.
BAT
amb
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP. MAX. UNIT
CTX
TX input capacitance
Note 1
15
pF
INH output function
t
t
t
INH turn-off delay
BUS = 0 V, LWAKE = V
measured from NSTB = 0.9 V to INH = 3.5 V
or 0 V, go to sleep command,
200
100
60
µs
µs
µs
inhoff
inhonl
inhonr
BAT
LWAKE to INH turn-on delay
BUS to INH turn-on delay
NSTB = 0 V, BUS = 0 V, measured from LWAKE = 3 V to
INH = 3.5 V
sleep mode, LWAKE = V , measured from BUS = 3.875 V to
INH = 3.5 V
BAT
BUS output function
t
t
;
Delay TX to BUS rising and
falling edge
from TX = 2.5 V to BUS = 3.875 V; bus load A and bus load B 13
22
µs
BOon
BOoff
t
t
t
t
t
BUS voltage rise time
bus load A, 9 V < V
bus load B, 9 V < V
bus load A, 9 V < V
bus load B, 9 V < V
< 16 V, measured at 1.5 V and 6.25 V 11
< 16 V, measured at 1.5 V and 6.25 V 11
< 16 V, measured at 1.5 V and 6.25 V 11
< 16 V, measured at 1.5 V and 6.25 V 11
18
18
18
18
µs
µs
µs
µs
µs
BrA
BrB
BfA
BfB
ir
BAT
BAT
BAT
BAT
BUS voltage rise time
BUS output voltage fall time
BUS output voltage fall time
BUS output current rise time
bus load B connected to –2 V,
9 V < V < 16 V, measured at 20% and 80% of load
4
BAT
capacitor current
t
BUS output current fall time
BUS high pulse width
bus load B connected to –2 V,
4
µs
µs
if
9 V < V
< 16 V, measured at 20% and 80% of load
BAT
capacitor current
t
TX = high for 64 µs, bus load condition A, 9 V < V
< 16 V; 35
93
wBh
BAT
minimum width measured at BUS = 6.25 V, maximum width
measured at BUS = 1.5 V
B
BUS output voltage harmonic
content; normal mode
f = 530 kHz to 1670 kHz, bus load B connected to –2 V,
70
5
dBµV
µs
HRM
TX = 7.81 kHz, 50% duty cycle, 9 V < V
< 16 V, Note 1
BAT
t
t
;
TX to BUS delay in 4X mode
4X/LOOP = 1 V, bus load B,
0.5
13
13
BO4Xon
BO4Xoff
9 V < V
< 16 V, from TX = 1.8 V to BUS = 3.875 V
BAT
t
t
;
Delay TX to RX rising and
falling edge in normal mode
measured from 1.8 V on TX to 2.5 V on RX
25
25
µs
pon
poff
t
t
;
Delay TX to RX rising and
falling edge in loop-back mode 2.5 V on RX
NSTB = 5 V, 4X = floating, measured from 1.8 V on TX to
µs
plbon
plboff
BUS input function
t
t
;
BUS input delay time, rising
and falling edge
measured from V
= 3.875 V to V = 2.5 V
0.2
2
1
5
µs
µs
µs
DRXon
DRXoff
BUS
RX
t
RX output transition time, rising NSTB = 5 V, measured at 10% and 90% of waveform
and falling edge
tRX
t
RX output transition time in
standby and sleep mode, rising
and falling edge
NSTB = 0 V, measured at 10% and 90% of waveform
tRXsl
t
BUS to RX delay in sleep and
standby modes
NSTB = 0 V, LWAKE = V , measured from BUS = 3.875 V
to RX = 2.5 V
8
60
µs
DRXsl
BAT
NOTES:
1. This parameter is characterized but not subject to production test.
10
2001 Feb 15
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
TEST CIRCUITS
5.1V
INH
100k
R/F
56k
TX
GND
NSTB
BUS
AU5783
S1
1uF
1.5k
4X/LOOP
LOAD
10.7k
S2
RX
BAT
S3
LWAKE
+
3.9k
I_LOG
V_bat
10k
SL01226
NOTE:
1. Check I_LOG with the following switch positions:
1. S1 = open = S2
2. S1 = open, S2 = closed
3. S1 = closed, S2 = open
4. S1 = closed = S2
Figure 4. Test circuit for loss of ground condition
11
2001 Feb 15
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
APPLICATION INFORMATION
µC with J1850 Link Controller
+5V
V
CC
VPWI
VPWO
port
port
3.9 k
Rb
1 k
5V
Reg.
100 KΩ
4X/LOOP
TX
RX
NSTB
INH
BAT
+12V
Ra
AU5783
10 k
LWAKE
Transceiver
GND
100 nF
R/F
LOAD
BUS
10.7 k
Rld
56 k
Rs
1%
1%
47 uH
470 pF
SAE/J1850/VPW BUS LINE
SL01227
NOTES:
1. Value of R depends, e.g., on type of bus node. Example: secondary node R =10.7 k, primary node R =1.5 k.
ld
ld
ld
2. For connection of the NSTB and 4X/LOOP pins there are different options, e.g., connect to a port pin or to V or to active low reset.
CC
Figure 5. Application of the AU5783 transceiver
12
2001 Feb 15
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
SO14: plastic small outline package; 14 leads; body width 3.9 mm
SOT108-1
13
2001 Feb 15
Philips Semiconductors
Preliminary specification
J1850/VPW transceiver with supply control function
AU5783
Data sheet status
[1]
Data sheet
status
Product
status
Definition
Objective
specification
Development
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
Preliminary
specification
Qualification
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make changes at any time without notice in order to
improve design and supply the best possible product.
Product
specification
Production
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Righttomakechanges—PhilipsSemiconductorsreservestherighttomakechanges, withoutnotice, intheproducts, includingcircuits,standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
Bare Die — All die are tested and guaranteed to comply with all data sheet limits up to the point of wafer sawing for a period of ninety (90) days
from the date of Philips’ delivery. If there are data sheet limits that are not guaranteed, these will be separately indicated in the data sheet. There
are no post packing tests performed on individual die or wafers. Philips Semiconductors has no control over third party procedures in the sawing,
handling, packing, or assembly of the die. Accordingly, Philips Semiconductors assumes no liability for device functionality or performance of the
die or system after third party sawing, handling, packaging, or assembly of the die. It is the responsibility of the customer to test and qualify their
application in which the die is used.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Copyright Philips Electronics North America Corporation 2001
All rights reserved. Printed in U.S.A.
Sunnyvale, California 94088–3409
Telephone 800-234-7381
Date of release: 02-01
Document order number:
9397 750 08083
Philips
Semiconductors
相关型号：
©2020 ICPDF网 联系我们和版权申明