HS13X-D [NKK]
Rotary Switch, 2 Positions, SPDT, Latched, 5A, 30VDC, Solder Terminal, D Flat Shaft Type Actuator, Panel Mount-threaded;型号: | HS13X-D |
厂家: | NIHON KAIHEIKI INDUSTRY CO. LTD. |
描述: | Rotary Switch, 2 Positions, SPDT, Latched, 5A, 30VDC, Solder Terminal, D Flat Shaft Type Actuator, Panel Mount-threaded 开关 光电二极管 |
文件: | 总5页 (文件大小:247K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Standard Size Rotaries Series HS TS PS
GENERAL SPECIFICATIONS
Electrical Capacity
Other Ratings
Resistive Load: HS13: 6A @ 125V AC, 3A @ 250V AC, or 5A @ 30V DC
HS16: 12A @ 125V AC or 6A @ 250V AC
TS: 6A @ 125/250V AC
PS: 30A @ 125/250V AC
Contact Resistance: 10 milliohms maximum
Insulation Resistance: 200 megohms minimum @ 500V DC
Dielectric Strength: 1,500V AC minimum for 1 minute minimum
Mechanical Life: HS: 15,000 operations minimum
TS: 30,000 operations minimum
PS: 10,000 operations minimum
Electrical Life: HS: 7,500 operations minimum
TS: 10,000 operations minimum
PS: 5,000 operations minimum
Indexing: 30° for HS16, TS & PS; 45° for HS13
Contact Timing: Nonshorting HS13; Shorting & Nonshorting HS16; Nonshorting TS; Nonshorting PS
Range of Operating Torque: HS16: 0.54 ~ 0.64Nm for first pole & 0.05Nm for each additional pole
HS13: 0.15 ~ 0.24Nm
TS: 0.09Nm for first pole & (0.07Nm x total number of poles) + 0.13Nm for additional poles
PS: 0.14Nm for each pole
Materials & Finishes
Knob: Phenolic resin
Shaft: HS13: brass; HS16, TS, & PS: brass with nickel plating
Bushing: HS13: brass; HS16, TS, & PS: brass with nickel plating
Case: Phenolic resin
Movable Contacts: HS13, HS16, & TS phosphor bronze; PS silver alloy
Stationary Contacts: HS13, HS16, & PS: brass with silver plating; TS: phosphor bronze
Terminals: HS: phosphor bronze; TS & PS: copper with silver plating
Environmental Data
Operating Temp Range:
–10°C through +70°C (+14°F through +158°F)
Humidity: 90 ~ 98% humidity for 96 hours @ 40°C (104°F)
Vibration: 10 ~ 55 Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
2
Shock: 50G (490m/s ) acceleration (tested in 3 right angled directions, with 3 shocks in each direction)
Installation
Mounting Torque:
2.94Nm (26 lb•in)
Maximum Panel Thickness: Shown with panel cutouts in following drawings
Soldering Time & Temperature: Manual Soldering (HS series only): See Profile A in Supplement section.
Standards & Certifications
UL Recognized: HS16 models 1– through 6–pole are recognized at 12A @ 125V AC & 6A @ 250V AC
See Supplement section to find UL rating details. UL File No. WOYR2.E44145
Add “/U” to end of part number to order UL mark on switch.
C-UL Recognized: HS16 models 1– through 6–pole are recognized at 12A @ 125V AC & 6A @ 250V AC
R
See Supplement section to find C-UL rating details. UL File No. WOYR8.E44145
Add “/C-UL” to end of part number to order UL mark on switch.
3-07
www.nikkaiswitches.com • Nihon Kaiheiki • Phone 81-44-813-8008 • Fax 81-44-813-8038
Standard Size Rotaries Series HS
6 AMP SINGLE POLE/NONSHORTING/45° INDEXING
Schematics
Round
Shaft
D-flat
Shaft
Number of
Positions
Stopper
Settings
Number of
Terminals
Load
Terminals
C
of Keyway
C
of Keyway
C of Keyway
L
L
L
HS13X
HS13Y
HS13Z
3
3
HS13X
HS13Y
HS13Z
HS13X-D
HS13Y-D
HS13Z-D
2
3
4
Fixed
Fixed
Fixed
1 COM, 2 LOAD
1 COM, 3 LOAD
1 COM, 4 LOAD
1 & 2
2
2
2
4
1, 2, & 3
1, 2, 3, & 4
1
1
1
C
1
C
1
C
1
Switch is viewed from shaft end and shown in position 1. Terminal numbers are not on switch. Standard Hardware shown on last page of this section.
(0.7) Typ
.028
M10 P0.75
Keyway
4
(10.3) Dia
.406
3
(10.5) Dia
.413
(6.0) Dia
.236
(9.5)
.374
2
(9.0)
.354
(1.5)
.059
1
(3.0) Dia
.118
(0.3)
.012
(16.0)
.630
(5.7) Typ
.224
COM
Maximum Effective Panel Thickness
With Locking Ring
(10.0) (10.0)
.394 .394
(4.8) Typ
.189
.150” (3.8mm)
Without Locking Ring
.189” (4.8mm)
(40.0)
1.575
(2.6) Dia Typ
.102
(34.0) Dia
1.339
HS13X
12 AMP/SHORTING & NONSHORTING/30° INDEXING
Knurled Shaft
D-flat Shaft
Number of
Positions
Stopper
Settings
Number of
Terminals
Nonshorting
Shorting
HS16-1S
HS16-2S
HS16-3S
HS16-4S
HS16-5S
HS16-6S
Nonshorting
HS16-1N
HS16-2N
HS16-3N
HS16-4N
HS16-5N
HS16-6N
Shorting
Pole
1P
2P
3P
4P
5P
6P
Schematic
C
HS16-1
HS16-2
HS16-3
HS16-4
HS16-5
HS16-6
HS16-1SN
HS16-2SN
HS16-3SN
HS16-4SN
HS16-5SN
HS16-6SN
2-11
2-11
2-11
2-11
2-11
2-11
2, 3, 4 . . . 11 1 COM, 11 LOAD
2, 3, 4 . . . 11 2 COM, 22 LOAD
2, 3, 4 . . . 11 3 COM, 33 LOAD
2, 3, 4 . . . 11 4 COM, 44 LOAD
2, 3, 4 . . . 11 5 COM, 55 LOAD
2, 3, 4 . . . 11 6 COM, 66 LOAD
1
1
11
2
10
9
3
C
of Keyway
L
4
5
8
6
7
Keyway
M10 P0.75
(6.0) Dia
.236
(65.0)
2.559
(8.0) Typ
.315
(4.4)
.173
(10.0)
.394
(24.5)
.965
(34.5)
1.358
(0.84) Typ
.033
(55.0)
2.165
(44.5)
1.752
(2.6) Dia Typ
.102
(6.24) Typ
.246
(54.5)
2.146
(64.5)
2.539
(10.3) Dia
.406
(15.0) (14.0)
.591
.551
(74.5)
2.933
(7.0) Max
.276
(10.5) Dia
.413
(9.5)
.374
(9.0)
.354
• On each deck of multipole devices common and load terminals
are in the same positions as shown in the schematic above.
(1.5)
.059
(3.0) Dia
.118
• Switch is viewed from the shaft end and shown in position 1.
Maximum Effective Panel Thickness
With Locking Ring
• Terminal numbers are on the switch bottom. Stopper positions
are molded on the top of the switch.
.189” (4.8mm)
Without Locking Ring
.228” (5.8mm)
• Standard Hardware shown on last page of this section.
HS16-2N
3-07
www.nikkaiswitches.com • Nihon Kaiheiki • Phone 81-44-813-8008 • Fax 81-44-813-8038
Standard Size Rotaries Series TS
6 AMP/NONSHORTING/ADJUSTABLE STOP/30° INDEXING
Number of
Positions
Stopper
Settings
Number of
Terminals
Shaft
Type
Model
TS1N
Pole
Schematic
C
of Keyway
L
C
1
1
1P
2-11
2-11
2-11
2-11
2-11
2, 3, 4 . . . 11
2, 3, 4 . . . 11
2, 3, 4 . . . 11
2, 3, 4 . . . 11
2, 3, 4 . . . 11
1 COM, 11 LOAD
2 COM, 22 LOAD
3 COM, 33 LOAD
4 COM, 44 LOAD
5 COM, 55 LOAD
D Flat
D Flat
D Flat
D Flat
D Flat
2
11
3
4
10
9
TS2N
TS3N
TS4N
TS5N
2P
3P
4P
5P
5
8
6
7
On each deck of multipole devices common
& load terminals are in the same positions
as shown in this schematic.
Switch is viewed from the shaft end and
shown in position 1.
Terminal numbers are on the switch bottom.
Stopper positions are molded on the top of
the switch.
• Standard Hardware shown on last page of this section.
Top
Bottom
Panel Cutouts
Keyway
(10.3) Dia
.406
(10.5) Dia
.413
(9.5)
.374
(9.0)
.354
(1.5)
.059
(4.4)
.173
(3.0) Dia
.118
Maximum Effective Panel Thickness
With Locking Ring
.189” (4.8mm)
Without Locking Ring
.228” (5.8mm)
(42.0) Dia
1.654
(44.0) Dia
1.732
M3 x 4 Typ
M10 P0.75
(6.0) Dia
.236
(22.0)
.866
(13.0)
.512
(34.0)
1.339
(46.0)
1.811
(58.0)
2.283
(15.6)
.614
(14.0)
.551
(70.0)
2.756
TS5N
3-07
www.nikkaiswitches.com • Nihon Kaiheiki • Phone 81-44-813-8008 • Fax 81-44-813-8038
Standard Size Rotaries Series PS
30 AMP/NONSHORTING/ADJUSTABLE STOP/30° INDEXING
Number of
Positions
Stopper
Settings
Number of
Terminals
Knurled
Shaft
D Flat
Shaft
Pole
Schematic
C
of Keyway
1
L
PS1
PS2
PS3
PS4
PS5
PS1N
PS2N
PS3N
PS4N
PS5N
1P
2-11
2-11
2-11
2-11
2-11
2, 3, 4 . . . 11
2, 3, 4 . . . 11
2, 3, 4 . . . 11
2, 3, 4 . . . 11
2, 3, 4 . . . 11
1 COM, 11 LOAD
2 COM, 22 LOAD
3 COM, 33 LOAD
4 COM, 44 LOAD
5 COM, 55 LOAD
C
1
2P
3P
4P
5P
2
11
3
4
10
9
5
8
6
7
On each deck of multipole devices common & load terminals are in the same positions as shown in this schematic. Switch is viewed from
the shaft end and shown in position 1. Terminal numbers are on switch bottom. Stopper positions are molded on the top of the switch.
• Standard Hardware shown on last page of this section.
Panel Cutout
Top
Bottom
(4.4)
.173
(4.5) Dia Typ
.177
(10.5) Dia
.413
(9.0)
.354
(3.0) Dia
.118
(20.0) R
.787
(40.0) Dia
1.575
Maximum Effective Panel Thickness
Without Locking Ring
M4
.189” (4.8mm)
(76.0) Dia
2.992
(70.0) Dia
2.756
M4 x 5 Typ
M10 P0.75
Keyway
(6.0) Dia
.236
(10.0)
.394
(7.0)
.276
(24.5)
.965
(42.0)
1.654
(59.5)
2.343
(15.0)
.591
(77.0)
3.031
(29.0)
1.142
(94.5)
3.720
(15.0) Max
.591
PS4N
3-07
www.nikkaiswitches.com • Nihon Kaiheiki • Phone 81-44-813-8008 • Fax 81-44-813-8038
Standard Size Rotaries Series HS TS PS
SHAFT TYPES
D Flat Shaft
Knurled Shaft
(6.0) Dia
.236
(6.0) Dia
.236
For use with
AT431 and AT432
Not for use with
AT431 or AT432
(4.4)
.173
(13.0)
.512
(20.0)
.787
(15.0)
.591
OPTIONAL KNOBS FOR D FLAT SHAFTS
AT431
Large Knob
AT432
Small Knob
Knob Orientation
The rotary
knobs used
on the D-flat
shafts can
be oriented
on the switch
to suit the
customer’s
particular
front panel
needs simply
by sliding the
knob over
Phenolic Resin
Phenolic Resin
Assembly Screw
(19.5)
.768
(15.6)
.614
Black only
with white
indicator
Black only
with white
indicator
(21.0)
.827
(24.0)
.945
line
line
(57.0)
2.244
(41.0)
1.614
(25.0) Dia
.984
(30.0) Dia
1.181
Set Screw
Adaptor
Shaft
(5.5)
.217
(5.5)
.217
(24.0)
.945
(21.0)
.827
the square
adaptor at
the preferred
orientation.
(9.0)
.354
(9.0)
.354
(29.0)
1.142
(28.0)
1.102
(21.0)
.827
(20.0)
.787
M2.3 x 0.4 x 0.8
M2.3 x 0.4 x 0.8
STOPPER SETTING
For HS16, TS, & PS Models
AT526
AT518
The HS16, TS, and PS switches are supplied with the stopper plate set for the
maximum number of positions allowed for that model. Prior to installation,
the desired stopper setting should be made:
AT520
AT526
1. Be sure the shaft is turned counterclockwise to the extreme left. If the
shaft is not turned counterclockwise to the extreme left, proper setting
cannot be achieved.
AT526
2. Loosen the nut far enough to allow raising the stopper plate for resetting.
3. Insert the stopper in the numbered hole for the desired stopper setting.
Satisfactory switch functioning cannot be assured if the stopper plate is
not properly positioned.
4. Tighten the nut firmly against the stopped plate.
Standard Hardware Supplied with HS, TS, and PS:
AT526 Hex Mounting Nut (quantity 3)
AT518 Locking Ring (quantity 1)
AT520 Split Lockwasher (quantity 1)
Use of mounting supports on PS is optional; screws are not provided.
3-07
www.nikkaiswitches.com • Nihon Kaiheiki • Phone 81-44-813-8008 • Fax 81-44-813-8038
相关型号:
HS13Z-D
Rotary Switch, 4 Positions, SP4T, Latched, 5A, 30VDC, Solder Terminal, D Flat Shaft Type Actuator, Panel Mount-threaded
NKK
©2020 ICPDF网 联系我们和版权申明