NESB007AT [NICHIA]

TYPE BLUE LED; 键入蓝色LED


型号：	NESB007AT
厂家：	NICHIA CORPORATION
描述：	TYPE BLUE LED 键入蓝色LED
文件：	总13页 (文件大小：600K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

No. STSE-CC5089A

<Cat.No.050615>

SPECIFICATIONS FOR NICHIA CHIP TYPE BLUE LED

MODEL : NESB007AT

NICHIA CORPORATION

-0-

Nichia STSE-CC5089A

<Cat.No.050615>

1.SPECIFICATIONS

(1) Absolute Maximum Ratings

Item

(Ta=25°C)

Unit

Symbol

Absolute Maximum Rating

Forward Current

Pulse Forward Current

Reverse Voltage

Power Dissipation

Operating Temperature

Storage Temperature

Soldering Temperature

IFP

Topr

Tstg

Tsld

°C

-40 ~ + 85

-40 ~ +100

Reflow Soldering : 260°C

Hand Soldering : 350°C

°C

for 10sec.

for 3sec.

IFP Conditions

Pulse Width 10msec. and Duty 1/10

(2) Initial Electrical/Optical Characteristics

Item Symbol Condition

Forward Voltage

(Ta=25°C)

Typ.

(3.6)

(150)

0.133

0.075

Max.

Unit

µA

mcd

IF=10[mA]

VR= 5[V]

4.0

Reverse Current

Luminous Intensity

IF=10[mA]

Chromaticity Coordinate

ꢀPlease refer to CIE 1931 chromaticity diagram.

(3) Ranking

(Ta=25°C)

Unit

Item

Symbol Condition

Min.

213

150

104

Max.

300

213

150

Rank U

Rank T

Rank S

IF=10[mA]

mcd

Luminous Intensity

ꢀLuminous Intensity Measurement allowance is ± 10%.

Color Rank

(IF=10mA,Ta=25°C)

Rank W

0.11

0.04

0.11

0.10

0.15

0.10

0.15

0.04

ꢀColor Coordinates Measurement allowance is ± 0.01.

ꢀOne delivery will include up to one color rank and three luminous intensity ranks of the products.

The quantity-ratio of the ranks is decided by Nichia.

-1-

Nichia STSE-CC5089A

<Cat.No.050615>

2.INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS

Please refer to figure’s page.

3.OUTLINE DIMENSIONS AND MATERIALS

Please refer to figure’s page.

Material as follows ;

Package

Encapsulating Resin :

Electrodes

Heat-Resistant Polymer

Epoxy Resin (with Diffused)

Ag Plating Copper Alloy

4.PACKAGING

· The LEDs are packed in cardboard boxes after taping.

Please refer to figure’s page.

The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity

· In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation.

· The LEDs may be damaged if the boxes are dropped or receive a strong impact against them,

so precautions must be taken to prevent any damage.

· The boxes are not water resistant and therefore must be kept away from water and moisture.

· When the LEDs are transported, we recommend that you use the same packing method as Nichia.

5.LOT NUMBER

The first six digits number shows lot number.

The lot number is composed of the following characters;

ꢁꢂꢃꢃꢃꢃ- Uꢄ

ꢁ - Year

( 4 for 2004, 5 for 2005 )

ꢂ - Month ( 1 for Jan., 9 for Sep., A for Oct., B for Nov. )

ꢃꢃꢃꢃ - Nichia's Product Number

U - Ranking by Color Coordinates

ꢄ - Ranking by Luminous Intensity

-2-

Nichia STSE-CC5089A

<Cat.No.050615>

6.RELIABILITY

(1) TEST ITEMS AND RESULTS

Standard

Number of

Damaged

0/50

Test Item

Resistance to

Test Method

JEITA ED-4701

300 301

Test Conditions

Note

2 times

Tsld=260°C, 10sec.

Soldering Heat

(Reflow Soldering)

Solderability

(Pre treatment 30°C,70%,168hrs.)

JEITA ED-4701

300 303

JEITA ED-4701

300 307

JEITA ED-4701

100 105

JEITA ED-4701

200 203

JEITA ED-4701

200 201

JEITA ED-4701

100 103

JEITA ED-4701

200 202

Tsld=215 ± 5°C, 3sec.

(Lead Solder)

0°C ~ 100°C

15sec. 15sec.

-40°C ~ 25°C ~ 100°C ~ 25°C

30min. 5min. 30min. 5min.

25°C ~ 65°C ~ -10°C

90%RH 24hrs./1cycle

Ta=100°C

1 time

0/50

(Reflow Soldering)

Thermal Shock

over 95%

20 cycles

Temperature Cycle

100 cycles

10 cycles

1000 hrs.

500 hrs.

Moisture Resistance Cyclic

High Temperature Storage

Temperature Humidity

Storage

Low Temperature Storage

Ta=60°C, RH=90%

Ta=-40°C

Steady State Operating Life

Condition 1

Steady State Operating Life

Condition 2

Steady State Operating Life

of High Temperature

Steady State Operating Life

of High Humidity Heat

Steady State Operating Life

of Low Temperature

Vibration

Ta=25°C, IF=10mA

Ta=25°C, IF=15mA

Ta=85°C, IF=4.2mA

60°C, RH=90%, IF=10mA

Ta=-40°C, IF=10mA

1000 hrs.

500 hrs.

1000 hrs.

48min.

JEITA ED-4701

400 403

100 ~ 2000 ~ 100Hz Sweep 4min.

200m/s²

3direction, 4cycles

3mm, 5 ± 1 sec.

Substrate Bending

Adhesion Strength

JEITA ED-4702

1 time

0/50

5N, 10 ± 1 sec.

(2) CRITERIA FOR JUDGING DAMAGE

Criteria for Judgement

Min. Max.

Item

Symbol Test Conditions

Forward Voltage

Reverse Current

Luminous Intensity

IF=10mA

VR=5V

IF=10mA

U.S.L.*)¯ 1.1

U.S.L.*)¯ 2.0

L.S.L.**)¯ 0.7

*) U.S.L. : Upper Standard Level

**) L.S.L. : Lower Standard Level

-3-

Nichia STSE-CC5089A

<Cat.No.050615>

7.CAUTIONS

(1) Moisture Proof Package

· When moisture is absorbed into the SMT package it may vaporize and expand during soldering.

There is a possibility that this can cause exfoliation of the contacts and damage to the optical

characteristics of the LEDs.

to a minimum in the package.

· The moisture proof package is made of an aluminum moisture proof bag with a zipper.

a moisture absorbent material (silica gel) is inserted into the aluminum moisture proof bag.

The silica gel changes its color from blue to pink as it absorbs moisture.

For this reason, the moisture proof package is used to keep moisture

A package of

(2) Storage

· Storage Conditions

Before opening the package :

The LEDs should be kept at 30°C or less and 90%RH or less. The LEDs should be used within a

year.

When storing the LEDs, moisture proof packaging with absorbent material (silica gel)

is recommended.

After opening the package :

The LEDs should be kept at 30°C or less and 70%RH or less.

The LEDs should be soldered

If unused LEDs remain, they should be

within 168 hours (7days) after opening the package.

stored in moisture proof packages, such as sealed containers with packages of moisture absorbent

material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag

and to reseal the moisture proof bag again.

· If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage

time, baking treatment should be performed using the following conditions.

Baking treatment : more than 24 hours at 65 ± 5°C

· Nichia LED electrodes are silver plated copper alloy. The silver surface may be affected by

environments which contain corrosive substances. Please avoid conditions which may cause the LED

to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering

operations. It is recommended that the User use the LEDs as soon as possible.

· Please avoid rapid transitions in ambient temperature, especially in high humidity environments where

condensation can occur.

(3) Heat Generation

· Thermal design of the end product is of paramount importance.

Please consider the heat generation

of the LED when making the system design. The coefficient of temperature increase per input

electric power is affected by the thermal resistance of the circuit board and density of LED placement

on the board, as well as other components. It is necessary to avoid intense heat generation and operate

within the maximum ratings given in this specification.

· The operating current should be decided after considering the ambient maximum temperature of LEDs.

-4-

Nichia STSE-CC5089A

<Cat.No.050615>

(4) Soldering Conditions

· The LEDs can be soldered in place using the reflow soldering method.

Nichia cannot make a

guarantee on the LEDs after they have been assembled using the dip soldering method.

· Recommended soldering conditions

Reflow Soldering

Lead Solder

Hand Soldering

Lead-free Solder

Pre-heat

Temperature

350°C Max.

120 ~ 150°C

180 ~ 200°C

Pre-heat time

Peak

Soldering time 3 sec. Max.

(one time only)

120 sec. Max.

240°C Max.

120 sec. Max.

260°C Max.

temperature

Soldering time

Condition

10 sec. Max.

refer to

10 sec. Max.

refer to

Temperature - profile 1. Temperature - profile 2.

(N₂reflow is recommended.)

ꢀAfter reflow soldering rapid cooling should be avoided.

[Temperature-profile (Surface of circuit board)]

Use the conditions shown to the under figure.

<1: Lead Solder>

<2: Lead-free Solder>

1~ 5°C / sec.

2.5 ~ 5°C / sec.

260°C Max.

10sec. Max.

240°C Max.

10sec. Max.

Pre-heating

1~ 5°C / sec.

180 ~ 200°C

2.5 ~ 5°C / sec.

120 ~ 150°C

60sec.Max.

Above 220°C

60sec.Max.

Above 200°C

120sec.Max.

[Recommended soldering pad design]

Use the following conditions shown in the figure.

8.8

(Unit : mm)

: Solder resist

· Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere

during air reflow. It is recommended that the User use the nitrogen reflow method.

· Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable,

a double-head soldering iron should be used. It should be confirmed beforehand whether the

characteristics of the LEDs will or will not be damaged by repairing.

· Reflow soldering should not be done more than two times.

· When soldering, do not put stress on the LEDs during heating.

· After soldering, do not warp the circuit board.

(5) Cleaning

· It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs.

When using

other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the

resin or not.

· Do not clean the LEDs by the ultrasonic.

Freon solvents should not be used to clean the LEDs because of worldwide regulations.

When it is absolutely necessary, the influence of ultrasonic

cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition.

Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur.

-5-

Nichia STSE-CC5089A

<Cat.No.050615>

(6) Static Electricity

· Static electricity or surge voltage damages the LEDs.

It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.

· All devices, equipment and machinery must be properly grounded. It is recommended that precautions

be taken against surge voltage to the equipment that mounts the LEDs.

· When inspecting the final products in which LEDs were assembled, it is recommended to check

whether the assembled LEDs are damaged by static electricity or not.

It is easy to find

static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended).

· Damaged LEDs will show some unusual characteristics such as the leak current remarkably

increases, the forward voltage becomes lower, or the LEDs do not light at the low current.

Criteria : (VF > 2.0V at IF=0.5mA)

(7) Others

· Care must be taken to ensure that the reverse voltage will not exceed the absolute maximum rating

when using the LEDs with matrix drive.

· The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent

looking directly at the LEDs with unaided eyes for more than a few seconds.

· Flashing lights have been known to cause discomfort in people; you can prevent this by taking

precautions during use. Also, people should be cautious when using equipment that has had LEDs

incorporated into it.

· The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such

as office equipment, communications equipment, measurement instruments and household appliances).

Consult Nichia’s sales staff in advance for information on the applications in which exceptional quality

and reliability are required, particularly when the failure or malfunction of the LEDs may directly

jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor

control systems, automobiles, traffic control equipment, life support systems and safety devices).

· User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written

consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before

disassembling or analysis.

· The formal specifications must be exchanged and signed by both parties before large volume purchase begins.

· The appearance and specifications of the product may be modified for improvement without notice.

-6-

Nichia STSE-CC5089A

<Cat.No.050615>

ICI Chromaticity Diagram

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

520

530

540

550

560

510

500

570

580

590

600

610

620

630

490

480

470

460

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

! Color Coordinates Measurement allowance is ± 0.01.

-7-

ꢀ Forward Voltage vs.

ꢀ Forward Current vs.

ꢀ Duty Ratio vs.

Forward Current

Relative Luminosity

Allowable Forward Current

4.0

100

Ta=25°C

3.5

3.0

2.5

2.0

1.5

1.0

0.5

2.5 3.0 3.5 4.0 4.5 5.0

10 20 30 40 50 60

Forward Current IFP (mA)

10 20

50 100

Forward Voltage VF (V)

Duty Ratio (%)

ꢀ Ambient Temperature vs.

Forward Voltage

Relative Luminosity

Allowable Forward Current

5.0

2.0

IFP=10mA

4.6

1.0

0.5

4.2

3.8

3.4

3.0

0.2

2.6

-60 -40 -20 0 20 40 60 80 100

80 100

Ambient Temperature Ta (°C)

Model

Title

No.

NESB007A

CHARACTERISTICS

050530540741

NICHIA CORPORATION

ꢀ Forward Current vs.

ꢀ Spectrum

Chromaticity Coordinate (λD)

1.2

1.0

0.8

0.6

0.4

0.2

0.10

Ta=25°C

IF=10mA

0.09

1mA(471.7nm)

5mA(471.0nm)

10mA(470.6nm)

0.08

0.07

0.06

0.05

50mA(469.3nm)

0.11 0.12 0.13 0.14 0.15 0.16

350 400 450 500 550 600 650

Wavelength λ (nm)

ꢀ Ambient Temperature vs.

ꢀ Forward Current vs.

ꢀ Directivity

Dominant Wavelength

0°

10°

20°

474

1.0

474

30°

Ta=25°C

IFP=10mA

40°

473

IFP=10mA

50°

472

471

470

469

472

471

470

469

468

60°

70°

80°

90°

0.5

468

90°

60°

30°

0°

0.5

1.0

10 20

Forward Current IFP (mA)

50 100

-60 -40 -20 0 20 40 60 80 100

Radiation Angle

Ambient Temperature Ta (°C)

Model

NESB007A

Title

No.

CHARACTERISTICS

050530540751

NICHIA CORPORATION

1.2

Anode

(R 0.3)

(0.9)

Cathode mark

(C 0.3)

Cathode

ITEM

PACKAGE

ENCAPSULATING RESIN

ELECTRODES

MATERIALS

Heat-Resistant Polymer

Epoxy Resin (with Diffused)

Ag Plating Copper Alloy

(0.23)

(0.35)

Unit

Model

NxSB007x

15/1

Title

No.

OUTLINE DIMENSIONS

NICHIA CORPORATION

Scale

Allow

050530429372

±0.1

Reel part

11.4^±1

9^±0.3

Taping part

-3

0.25^±0.05

φ 180

4^±0.1

+0.1

-0

φ 1.5

2^±0.05

Cathode mark

Label

1.44^±0.1

4^±0.1

φ 1^+0.2

XXXX LED

-0

TYPE NxSx007xT

LOT xxxxxx-U

1.36^±0.1

QTY

pcs

Reel End of tape

No LEDs

LEDs mounting part

No LEDs

Pull direction

Top cover

tape

Embossed carrier tape

Reel Lead Min.160mm (No LEDs is more than 40)

Reel Lead Min.400mm

Reel Lead Min.40mm (No LEDs)

3,000pcs/Reel

Unit

NxSx007xT

Model

Title

Taping is based on the JIS C 0806 : Packaging of Electronic

Components on Continuous Tapes.

TAPING DIMENSIONS

050530316604

NICHIA CORPORATION

Scale

Allow

No.

Nichia STSE-CC5089A

<Cat.No.050615>

The reel and moisture absorbent material are put in the moisture proof foil bag

and then heat sealed.

Reel

Label

NICHIA

Seal

XXXX LED

TYPE

LOT

NxSx007xT

xxxxxx-U

PCS

QTY

NICHIA CORPORATION

491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN

Moisture proof foil bag

Moisture

absorbent material

The box is partitioned with the

cardboard.

Label

NICHIA

XXXX LED

^NichiaLED

TYPE

RANK

QTY

NxSx007xT

PCS

NICHIA CORPORATION

491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN

Packing unit

Reel/bag

1reel

Quantity/bag (pcs)

Moisture proof foil bag

3,000 MAX.

Cardboard box

Cardboard box S

Cardboard box M

Cardboard box L

Dimensions (mm)

291¯237¯120¯8t

259¯247¯243¯5t

444¯262¯259¯8t

Reel/box

Quantity/box (pcs)

21,000 MAX.

45,000 MAX.

90,000 MAX.

7reel MAX.

15reel MAX.

30reel MAX.

Model

Title

NxSx007xT

PACKING

NICHIA CORPORATION

No.

050530540761

-12-

NESB007AT [NICHIA]

相关型号：

NESB007T

NESB008AT

NESB017T

NESB021T

NESB064T

NESB426CT

NESB505CT

NESD-100-12

NESD-100-15

NESD-100-24

NESD-100-48

NESD-100-5