MTD2955ET4 [MOTOROLA]
12A, 60V, 0.3ohm, P-CHANNEL, Si, POWER, MOSFET, DPAK-3;型号: | MTD2955ET4 |
厂家: | MOTOROLA |
描述: | 12A, 60V, 0.3ohm, P-CHANNEL, Si, POWER, MOSFET, DPAK-3 开关 脉冲 晶体管 |
文件: | 总10页 (文件大小:210K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Order this document
by MTD2955E/D
SEMICONDUCTOR TECHNICAL DATA
Motorola Preferred Device
P–Channel Enhancement–Mode Silicon Gate
TMOS POWER FET
12 AMPERES
60 VOLTS
This advanced TMOS E–FET is designed to withstand high
energy in the avalanche and commutation modes. The new energy
efficient design also offers a drain–to–source diode with a fast
recovery time. Designed for low voltage, high speed switching
applications in power supplies, converters and PWM motor
controls, these devices are particularly well suited for bridge circuits
where diode speed and commutating safe operating areas are
critical and offer additional safety margin against unexpected
voltage transients.
R
= 0.3 OHM
DS(on)
•
•
Avalanche Energy Specified
Source–to–Drain Diode Recovery Time Comparable to a
Discrete Fast Recovery Diode
D
•
•
•
Diode is Characterized for Use in Bridge Circuits
I
and V Specified at Elevated Temperature
DSS
DS(on)
Surface Mount Package Available in 16 mm, 13–inch/2500
Unit Tape & Reel, Add T4 Suffix to Part Number
Replaces the MTD2955
G
CASE 369A–13, Style 2
DPAK
•
S
MAXIMUM RATINGS (T = 25°C unless otherwise noted)
C
Rating
Symbol
Value
60
Unit
Vdc
Vdc
Drain–Source Voltage
V
DSS
Drain–Gate Voltage (R
= 1.0 MΩ)
Gate–Source Voltage — Continuous
V
DGR
60
GS
V
± 15
± 25
Vdc
Vpk
GS
Gate–Source Voltage — Non–Repetitive (t ≤ 10 ms)
V
GSM
p
Drain Current — Continuous
Drain Current — Continuous @ 100°C
Drain Current — Single Pulse (t ≤ 10 µs)
I
I
12
7.0
36
Adc
Apk
D
D
I
p
DM
Total Power Dissipation
Derate above 25°C
Total Power Dissipation @ T = 25°C, when mounted to minimum recommended pad size
P
D
75
0.6
1.75
Watts
W/°C
Watts
A
Operating and Storage Temperature Range
T , T
stg
–55 to 150
216
°C
J
Single Pulse Drain–to–Source Avalanche Energy — Starting T = 25°C
E
AS
mJ
J
(V
DD
= 25 Vdc, V = 10 Vdc, I = 12 Apk, L = 3.0 mH, R = 25 Ω)
GS L G
Thermal Resistance — Junction to Case
Thermal Resistance — Junction to Ambient
Thermal Resistance — Junction to Ambient, when mounted to minimum recommended pad size
R
θJC
R
θJA
R
θJA
1.67
100
71.4
°C/W
Maximum Temperature for Soldering Purposes, 1/8″ from case for 10 seconds
T
L
260
°C
Designer’s Data for “Worst Case” Conditions — The Designer’s Data Sheet permits the design of most circuits entirely from the information presented. SOA Limit
curves — representing boundaries on device characteristics — are given to facilitate “worst case” design.
E–FET and Designer’s are trademarks of Motorola, Inc. TMOS is a registered trademark of Motorola, Inc.
Thermal Clad is a trademark of the Bergquist Company.
Preferred devices are Motorola recommended choices for future use and best overall value.
REV 3
Motorola, Inc. 1995
ELECTRICAL CHARACTERISTICS (T = 25°C unless otherwise noted)
J
Characteristic
Symbol
Min
Typ
Max
Unit
OFF CHARACTERISTICS
Drain–Source Breakdown Voltage
V
(BR)DSS
(V
GS
= 0 Vdc, I = 250 µAdc)
60
—
—
85
—
—
Vdc
mV/°C
D
Temperature Coefficient (Positive)
Zero Gate Voltage Drain Current
I
µAdc
DSS
(V
DS
(V
DS
= 60 Vdc, V
= 60 Vdc, V
= 0 Vdc)
= 0 Vdc, T = 125°C)
—
—
—
—
10
100
GS
GS
J
Gate–Body Leakage Current (V
= ±15 Vdc, V
DS
= 0)
I
—
—
100
nAdc
GS
GSS
ON CHARACTERISTICS (1)
Gate Threshold Voltage
V
GS(th)
(V
DS
= V , I = 250 µAdc)
2.0
—
—
3.0
4.0
—
Vdc
mV/°C
GS
D
Temperature Coefficient (Negative)
Static Drain–Source On–Resistance (V
= 10 Vdc, I = 6.0 Adc)
R
V
—
0.26
0.30
Ohm
Vdc
GS
D
DS(on)
Drain–Source On–Voltage (V
GS
= 10 Vdc)
DS(on)
(I = 12 Adc)
—
—
—
—
4.3
3.8
D
(I = 6.0 Adc, T = 125°C)
D
J
Forward Transconductance (V
DS
= 13 Vdc, I = 6.0 Adc)
g
3.0
4.8
—
mhos
pF
D
FS
DYNAMIC CHARACTERISTICS
Input Capacitance
C
—
—
—
565
225
45
700
315
100
iss
(V
DS
= 25 Vdc, V = 0 Vdc,
GS
f = 1.0 MHz)
Output Capacitance
C
oss
Reverse Transfer Capacitance
C
rss
SWITCHING CHARACTERISTICS (2)
Turn–On Delay Time
t
—
—
—
—
—
—
—
—
9.0
39
20
80
35
20
32
—
—
—
ns
d(on)
(V
= 30 Vdc, I = 12 Adc,
D
Rise Time
DD
DS
t
r
V
= 10 Vdc,
GS
G
Turn–Off Delay Time
Fall Time
t
17
d(off)
R
= 9.1 Ω)
t
f
8.0
16
Gate Charge
(See Figure 8)
Q
T
Q
1
Q
2
Q
3
nC
3.0
6.0
5.0
(V
= 48 Vdc, I = 12 Adc,
D
V
GS
= 10 Vdc)
SOURCE–DRAIN DIODE CHARACTERISTICS
Forward On–Voltage (1)
V
Vdc
ns
SD
(I = 12 Adc, V
(I = 12 Adc, V
GS
= 0 Vdc)
= 0 Vdc, T = 125°C)
S
GS
—
—
2.2
1.8
3.8
—
S
J
Reverse Recovery Time
(See Figure 14)
t
—
—
—
—
100
75
—
—
—
—
rr
t
(I = 12 Adc, V
= 0 Vdc,
dI /dt = 100 A/µs)
a
S
GS
S
t
25
b
Reverse Recovery Stored Charge
Q
0.475
µC
RR
INTERNAL PACKAGE INDUCTANCE
Internal Drain Inductance
(Measured from the drain lead 0.25″ from package to center of die)
L
—
—
4.5
7.5
—
—
nH
nH
D
Internal Source Inductance
(Measured from the source lead 0.25″ from package to source bond pad)
L
S
(1) Pulse Test: Pulse Width ≤ 300 µs, Duty Cycle ≤ 2%.
(2) Switching characteristics are independent of operating junction temperature.
2
Motorola TMOS Power MOSFET Transistor Device Data
TYPICAL ELECTRICAL CHARACTERISTICS
– 24
– 18
– 12
– 6
– 24
V
= 10 V
T
= 25
°
C
V
≥ 10 V
GS
J
DS
T
= – 55°C
J
9 V
– 20
– 16
–12
– 8
– 4
0
8 V
7 V
25°C
100°C
6 V
5 V
0
0
–1
–2
– 3
– 4
– 5
– 6
– 7
– 8
– 9
–10
–2
– 3
– 4
– 5
– 6
– 7
– 8
– 9
– 10
V
, DRAIN–TO–SOURCE VOLTAGE (VOLTS)
V , GATE–TO–SOURCE VOLTAGE (VOLTS)
GS
DS
Figure 1. On–Region Characteristics
Figure 2. Transfer Characteristics
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.48
0.44
0.40
V
= 10 V
GS
T
= 25°C
J
T
= 100°C
J
V
= 10 V
GS
0.36
0.32
0.28
0.24
0.20
25°C
15 V
– 55°C
0.2
0.1
0
– 2 – 4 – 6 – 8 –10 –12 –14 –16 – 18 – 20 – 22 – 24
, DRAIN CURRENT (AMPS)
0
– 2 – 4 – 6 – 8 –10 –12 –14 –16 –18 – 20 – 22 – 24
, DRAIN CURRENT (AMPS)
I
I
D
D
Figure 3. On–Resistance versus Drain Current
and Temperature
Figure 4. On–Resistance versus Drain Current
and Gate Voltage
1.8
1.6
1000
V
= 0 V
GS
V
= 10 V
GS
= 6 A
I
D
T
= 125°C
J
1.4
1.2
100°C
100
25°C
1.0
0.8
0.6
10
– 50
– 25
0
25
50
75
100
C)
125
150
–15
– 20
– 25
V , DRAIN–TO–SOURCE VOLTAGE (VOLTS)
DS
– 30
– 35
– 40
– 45
– 50 – 55
– 60
T , JUNCTION TEMPERATURE (
°
J
Figure 5. On–Resistance Variation with
Temperature
Figure 6. Drain–To–Source Leakage
Current versus Voltage
Motorola TMOS Power MOSFET Transistor Device Data
3
POWER MOSFET SWITCHING
Switching behavior is most easily modeled and predicted
by recognizing that the power MOSFET is charge controlled.
The lengths of various switching intervals (∆t) are deter-
mined by how fast the FET input capacitance can be charged
by current from the generator.
The capacitance (C ) is read from the capacitance curve at
iss
a voltage corresponding to the off–state condition when cal-
culating t
and is read at a voltage corresponding to the
d(on)
on–state when calculating t
.
d(off)
At high switching speeds, parasitic circuit elements com-
plicate the analysis. The inductance of the MOSFET source
lead, inside the package and in the circuit wiring which is
common to both the drain and gate current paths, produces a
voltage at the source which reduces the gate drive current.
The voltage is determined by Ldi/dt, but since di/dt is a func-
tion of drain current, the mathematical solution is complex.
The MOSFET output capacitance also complicates the
mathematics. And finally, MOSFETs have finite internal gate
resistance which effectively adds to the resistance of the
driving source, but the internal resistance is difficult to mea-
sure and, consequently, is not specified.
The resistive switching time variation versus gate resis-
tance (Figure 9) shows how typical switching performance is
affected by the parasitic circuit elements. If the parasitics
were not present, the slope of the curves would maintain a
value of unity regardless of the switching speed. The circuit
used to obtain the data is constructed to minimize common
inductance in the drain and gate circuit loops and is believed
readily achievable with board mounted components. Most
power electronic loads are inductive; the data in the figure is
taken with a resistive load, which approximates an optimally
snubbed inductive load. Power MOSFETs may be safely op-
erated into an inductive load; however, snubbing reduces
switching losses.
The published capacitance data is difficult to use for calculat-
ing rise and fall because drain–gate capacitance varies
greatly with applied voltage. Accordingly, gate charge data is
used. In most cases, a satisfactory estimate of average input
current (I
the drive circuit so that
) can be made from a rudimentary analysis of
G(AV)
t = Q/I
G(AV)
During the rise and fall time interval when switching a resis-
tive load, V remains virtually constant at a level known as
GS
the plateau voltage, V
. Therefore, rise and fall times may
SGP
be approximated by the following:
t = Q x R /(V
– V )
GSP
r
2
G
GG
t = Q x R /V
f
2
G
GSP
where
V
= the gate drive voltage, which varies from zero to V
= the gate drive resistance
GG
GG
R
G
and Q and V
GSP
are read from the gate charge curve.
2
During the turn–on and turn–off delay times, gate current is
not constant. The simplest calculation uses appropriate val-
ues from the capacitance curves in a standard equation for
voltage change in an RC network. The equations are:
t
t
= R
= R
C
C
In [V
/(V
GG GG
– V
)]
GSP
d(on)
G
iss
In (V
/V
GG GSP
)
d(off)
G
iss
1600
1400
V
= 0
DS
V
= 0
T
= 25°C
GS
J
C
C
iss
1200
1000
800
600
400
200
0
rss
C
iss
C
oss
C
rss
10
5
0
5
10
15
20
25
V
V
DS
GS
GATE–TO–SOURCE OR DRAIN–TO–SOURCE VOLTAGE (VOLTS)
Figure 7. Capacitance Variation
4
Motorola TMOS Power MOSFET Transistor Device Data
1000
100
10
14
12
10
8
70
60
V
I
= 30 V
= 12 A
= 10 V
= 25°C
DD
D
QT
V
T
GS
50
J
V
I
GS
Q1
Q2
40
30
20
tr
6
t
d(off)
d(on)
= 12 A
t
D
4
T
= 25°C
J
t
f
2
0
10
0
Q3
V
DS
1
0
2
4
6
8
10
12
14
16
18
1
10
100
Q
, TOTAL GATE CHARGE (nC)
R
, GATE RESISTANCE (OHMS)
G
G
Figure 8. Gate–To–Source and Drain–To–Source
Voltage versus Total Charge
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
DRAIN–TO–SOURCE DIODE CHARACTERISTICS
12
V
= 0 V
GS
= 25
T
°C
J
10
8
6
4
2
0
0.5
0.7
0.9
1.1
1.3
1.5
1.7
1.9
2.1 2.2
V
, SOURCE–TO–DRAIN VOLTAGE (VOLTS)
SD
Figure 10. Diode Forward Voltage versus Current
SAFE OPERATING AREA
The Forward Biased Safe Operating Area curves define
the maximum simultaneous drain–to–source voltage and
drain current that a transistor can handle safely when it is for-
ward biased. Curves are based upon maximum peak junc-
able operation, the stored energy from circuit inductance dis-
sipated in the transistor while in avalanche must be less than
the rated limit and adjusted for operating conditions differing
from those specified. Although industry practice is to rate in
terms of energy, avalanche energy capability is not a con-
stant. The energy rating decreases non–linearly with an in-
crease of peak current in avalanche and peak junction
temperature.
tion temperature and a case temperature (T ) of 25°C. Peak
C
repetitive pulsed power limits are determined by using the
thermal response data in conjunction with the procedures
discussed in AN569, “Transient Thermal Resistance–Gener-
al Data and Its Use.”
Although many E–FETs can withstand the stress of drain–
to–source avalanche at currents up to rated pulsed current
Switching between the off–state and the on–state may tra-
verse any load line provided neither rated peak current (I
)
DM
) is exceeded and the transition time
(I
), the energy rating is specified at rated continuous cur-
DM
nor rated voltage (V
DSS
rent (I ), in accordance with industry custom. The energy rat-
D
(t ,t ) do not exceed 10 µs. In addition the total power aver-
r f
ing must be derated for temperature as shown in the
accompanying graph (Figure 12). Maximum energy at cur-
aged over a complete switching cycle must not exceed
(T
– T )/(R ).
J(MAX)
C
θJC
rents below rated continuous I can safely be assumed to
A Power MOSFET designated E–FET can be safely used
D
in switching circuits with unclamped inductive loads. For reli-
Motorola TMOS Power MOSFET Transistor Device Data
equal the values indicated.
5
SAFE OPERATING AREA
100
10
240
I
= 12 A
V
= 20 V
D
GS
SINGLE PULSE
= 25
200
160
120
T
°C
C
100
µ
s
1 ms
10 ms
1.0
0.1
dc
80
40
0
R
LIMIT
THERMAL LIMIT
PACKAGE LIMIT
DS(on)
0.01
0.1
1.0
10
100
25
50
75
100
125
C)
150
V
, DRAIN–TO–SOURCE VOLTAGE (VOLTS)
T , STARTING JUNCTION TEMPERATURE (
°
DS
J
Figure 11. Maximum Rated Forward Biased
Safe Operating Area
Figure 12. Maximum Avalanche Energy versus
Starting Junction Temperature
1.0
D = 0.5
0.2
0.1
0.1
P
(pk)
R
(t) = r(t) R
JC θJC
θ
D CURVES APPLY FOR POWER
PULSE TRAIN SHOWN
0.05
0.02
t
READ TIME AT t
T
1
1
0.01
t
– T = P R (t)
(pk) θJC
2
J(pk)
C
SINGLE PULSE
DUTY CYCLE, D = t /t
1 2
0.01
1.0E–05
1.0E–04
1.0E–03
1.0E–02
1.0E–01
1.0E+00
1.0E+01
t, TIME (s)
Figure 13. Thermal Response
di/dt
I
S
t
rr
t
t
a
b
TIME
0.25 I
t
S
p
I
S
Figure 14. Diode Reverse Recovery Waveform
6
Motorola TMOS Power MOSFET Transistor Device Data
INFORMATION FOR USING THE DPAK SURFACE MOUNT PACKAGE
RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must be
the correct size to ensure proper solder connection interface
between the board and the package. With the correct pad
geometry, the packages will self align when subjected to a
solder reflow process.
0.165
4.191
0.118
3.0
0.100
2.54
0.063
1.6
0.190
4.826
0.243
6.172
inches
mm
POWER DISSIPATION FOR A SURFACE MOUNT DEVICE
The power dissipation for a surface mount device is a
dissipation can be increased. Although one can almost double
the power dissipation with this method, one will be giving up
area on the printed circuit board which can defeat the purpose
of using surface mount technology. For example, a graph of
function of the drain pad size. These can vary from the
minimum pad size for soldering to a pad size given for
maximum power dissipation. Power dissipation for a surface
mount device is determined by T
junction temperature of the die, R
θJA
, the maximum rated
, the thermal resistance
R
versus drain pad area is shown in Figure 15.
J(max)
θJA
from the device junction to ambient, and the operating
temperature, T . Using the values provided on the data sheet,
100
Board Material = 0.0625
″
A
G–10/FR–4, 2 oz Copper
P
can be calculated as follows:
D
1.75 Watts
80
60
40
20
T
= 25°C
A
T
– T
A
J(max)
P
=
°
D
R
θJA
3.0 Watts
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature T of 25°C, one can
calculate the power dissipation of the device. For a DPAK
device, P is calculated as follows.
A
5.0 Watts
D
0
2
4
6
8
10
A, Area (square inches)
150°C – 25°C
= 1.75 Watts
P
=
D
Figure 15. Thermal Resistance versus Drain Pad
Area for the DPAK Package (Typical)
71.4°C/W
The 71.4°C/W for the DPAK package assumes the use of
the recommended footprint on a glass epoxy printed circuit
board to achieve a power dissipation of 1.75 Watts. There are
other alternatives to achieving higher power dissipation from
thesurfacemountpackages. Oneistoincreasetheareaofthe
drain pad. By increasing the area of the drain pad, the power
Another alternative would be to use a ceramic substrate or
an aluminum core board such as Thermal Clad . Using a
board material such as Thermal Clad, an aluminum core
board, the power dissipation can be doubled using the same
footprint.
Motorola TMOS Power MOSFET Transistor Device Data
7
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. Solder
stencils are used to screen the optimum amount. These
stencils are typically 0.008 inches thick and may be made of
brass or stainless steel. For packages such as the SC–59,
SC–70/SOT–323, SOD–123, SOT–23, SOT–143, SOT–223,
SO–8, SO–14, SO–16, and SMB/SMC diode packages, the
stencil opening should be the same as the pad size or a 1:1
packages. The pattern of the opening in the stencil for the
drain pad is not critical as long as it allows approximately 50%
of the pad to be covered with paste.
SOLDER PASTE
OPENINGS
2
registration. This is not the case with the DPAK and D PAK
packages. If one uses a 1:1 opening to screen solder onto the
drain pad, misalignment and/or “tombstoning” may occur due
to an excess of solder. For these two packages, the opening
in the stencil for the paste should be approximately 50% of the
tab area. The opening for the leads is still a 1:1 registration.
STENCIL
Figure 16. Typical Stencil for DPAK and
2
2
D PAK Packages
Figure 16 shows a typical stencil for the DPAK and D PAK
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
• When shifting from preheating to soldering, the maximum
temperature gradient shall be 5°C or less.
• After soldering has been completed, the device should be
allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
• Always preheat the device.
• The delta temperature between the preheat and soldering
should be 100°C or less.*
• Mechanical stress or shock should not be applied during
cooling.
• When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10°C.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
* Due to shadowing and the inability to set the wave height to
2
• The soldering temperature and time shall not exceed
260°C for more than 10 seconds.
incorporate other surface mount components, the D PAK is
not recommended for wave soldering.
8
Motorola TMOS Power MOSFET Transistor Device Data
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control
line on the graph shows the actual temperature that might be
experienced on the surface of a test board at or near a central
solder joint. The two profiles are based on a high density and
a low density board. The Vitronics SMD310 convection/in-
frared reflow soldering system was used to generate this
profile. The type of solder used was 62/36/2 Tin Lead Silver
with a melting point between 177–189°C. When this type of
furnace is used for solder reflow work, the circuit boards and
solder joints tend to heat first. The components on the board
are then heated by conduction. The circuit board, because it
has a large surface area, absorbs the thermal energy more
efficiently, then distributes this energy to the components.
Because of this effect, the main body of a component may be
up to 30 degrees cooler than the adjacent solder joints.
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones, and a figure
for belt speed. Taken together, these control settings make up
a heating “profile” for that particular circuit board. On
machines controlled by a computer, the computer remembers
these profiles from one operating session to the next. Figure
17 shows a typical heating profile for use when soldering a
surface mount device to a printed circuit board. This profile will
vary among soldering systems but it is a good starting point.
Factors that can affect the profile include the type of soldering
system in use, density and types of components on the board,
typeofsolderused, andthetypeofboardorsubstratematerial
being used. This profile shows temperature versus time. The
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
STEP 6
VENT
STEP 7
COOLING
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 2
VENT
“SOAK” ZONES 2 & 5
“RAMP”
STEP 3
HEATING
205
PEAK AT
SOLDER JOINT
° TO 219°C
200
°
C
C
170°C
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
160°C
150°C
150°
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
100°C
140°C
MASS OF ASSEMBLY)
100
°
C
C
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
50°
TIME (3 TO 7 MINUTES TOTAL)
T
MAX
Figure 17. Typical Solder Heating Profile
Motorola TMOS Power MOSFET Transistor Device Data
9
PACKAGE DIMENSIONS
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
SEATING
PLANE
–T–
2. CONTROLLING DIMENSION: INCH.
C
B
R
INCHES
MILLIMETERS
E
V
DIM
A
B
C
D
E
MIN
MAX
0.250
0.265
0.094
0.035
0.040
0.047
MIN
5.97
6.35
2.19
0.69
0.84
0.94
MAX
6.35
6.73
2.38
0.88
1.01
1.19
0.235
0.250
0.086
0.027
0.033
0.037
Z
A
K
S
F
G
H
J
K
L
0.180 BSC
4.58 BSC
U
0.034
0.018
0.102
0.040
0.023
0.114
0.87
0.46
2.60
1.01
0.58
2.89
0.090 BSC
2.29 BSC
F
J
R
S
U
V
0.175
0.020
0.020
0.030
0.138
0.215
0.050
–––
0.050
–––
4.45
0.51
0.51
0.77
3.51
5.46
1.27
–––
1.27
–––
L
H
STYLE 2:
PIN 1. GATE
D 2 PL
0.13 (0.005)
Z
2. DRAIN
3. SOURCE
4. DRAIN
M
G
T
CASE 369A–13
ISSUE W
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representationorguaranteeregarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
andspecifically disclaims any and all liability, includingwithoutlimitationconsequentialorincidentaldamages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintendedor unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
Literature Distribution Centers:
USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036.
EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England.
JAPAN: Nippon Motorola Ltd.; 4–32–1, Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan.
ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong.
MTD2955E/D
CODELINE TO BE PLACED HERE
◊
©2020 ICPDF网 联系我们和版权申明