MMBD353LT1 [MOTOROLA]
Dual Hot Carrier Mixer Diodes; 双热载流子二极管混频器
| 型号： | MMBD353LT1 |
| 厂家： | 
MOTOROLA |
| 描述： | Dual Hot Carrier Mixer Diodes |
| 文件： | 总4页 (文件大小：61K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Order this document
by MMBD352LT1/D
SEMICONDUCTOR TECHNICAL DATA
These devices are designed primarily for UHF mixer applications but are suitable
also for use in detector and ultra–fast switching circuits.
•
•
Very Low Capacitance — Less Than 1.0 pF @ Zero Volts
Low Forward Voltage — 0.5 Volts (Typ) @ I = 10 mA
F
3
1
2
MAXIMUM RATINGS (EACH DIODE)
1
2
ANODE
CATHODE
Rating
Symbol
Value
Unit
3
CATHODE/ANODE
Continuous Reverse Voltage
THERMAL CHARACTERISTICS
Characteristic
V
7.0
V
CC
R
MMBD352LT1
CASE 318–08, STYLE 11
SOT–23 (TO–236AB)
Symbol
Max
Unit
(1)
Total Device Dissipation FR–5 Board
P
225
mW
D
T
= 25°C
A
1
2
Derate above 25°C
1.8
556
300
mW/°C
°C/W
mW
CATHODE
ANODE
3
Thermal Resistance, Junction to Ambient
Total Device Dissipation
R
JA
D
CATHODE/ANODE
P
(2)
Alumina Substrate
T
A
= 25°C
MMBD353LT1
CASE 318–08, STYLE 19
SOT–23 (TO–236AB)
Derate above 25°C
2.4
417
mW/°C
°C/W
°C
Thermal Resistance, Junction to Ambient
Junction and Storage Temperature
DEVICE MARKING
R
JA
T , T
J stg
–55 to +150
ANODE
1
3
MMBD352LT1 = M5G; MMBD353LT1 = M4F; MMBD354LT1 = M6H; MMBD355LT1 = MJ1
ELECTRICAL CHARACTERISTICS (T = 25°C unless otherwise noted) (EACH DIODE)
2
CATHODE
ANODE
A
MMBD354LT1
CASE 318–08, STYLE 9
SOT–23 (TO–236AB)
Characteristic
Symb
ol
Min
Max
Unit
OFF CHARACTERISTICS
Forward Voltage
(I = 10 mAdc)
F
V
—
0.60
V
A
F
CATHODE
ANODE
3
1
Reverse Voltage Leakage Current
I
R
(V = 3.0 V)
—
—
0.25
10
R
2
(V = 7.0 V)
R
CATHODE
MMBD355LT1
CASE 318–08, STYLE 12
SOT–23 (TO–236AB)
Capacitance
(V = 0 V, f = 1.0 MHz)
R
C
—
1.0
pF
1. FR–5 = 1.0
2. Alumina = 0.4
0.75 0.062 in.
0.3 0.024 in. 99.5% alumina.
Thermal Clad is a trademark of the Bergquist Company
REV 2
Motorola, Inc. 1997
TYPICAL CHARACTERISTICS
1.0
100
10
T
= 85°C
0.9
A
T
= –40°C
A
0.8
0.7
0.6
1.0
0.1
T
= 25°C
A
0.3
0.4
0.5
0.6
0.7
0.8
0
1.0
2.0
V , REVERSE VOLTAGE (VOLTS)
R
3.0
4.0
V , FORWARD VOLTAGE (VOLTS)
F
Figure 1. Forward Voltage
Figure 2. Capacitance
2
Motorola Small–Signal Transistors, FETs and Diodes Device Data
INFORMATION FOR USING THE SOT–23 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
0.037
0.95
0.037
0.95
0.079
2.0
0.035
0.9
0.031
0.8
inches
mm
SOT–23
SOT–23 POWER DISSIPATION
The power dissipation of the SOT–23 is a function of the
SOLDERING PRECAUTIONS
pad size. This can vary from the minimum pad size for
soldering to a pad size given for maximum power dissipation.
Power dissipation for a surface mount device is determined
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
by T
, the maximum rated junction temperature of the
, the thermal resistance from the device junction to
J(max)
die, R
θJA
ambient, and the operating temperature, T . Using the
A
values provided on the data sheet for the SOT–23 package,
P
can be calculated as follows:
D
•
•
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100°C or less.*
T
– T
A
J(max)
P
=
D
R
θJA
•
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10°C.
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature T of 25°C, one can
A
calculate the power dissipation of the device which in this
case is 225 milliwatts.
•
•
•
The soldering temperature and time shall not exceed
260°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient shall be 5°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
150°C – 25°C
556°C/W
P
=
= 225 milliwatts
D
The 556°C/W for the SOT–23 package assumes the use
of the recommended footprint on a glass epoxy printed circuit
board to achieve a power dissipation of 225 milliwatts. There
are other alternatives to achieving higher power dissipation
from the SOT–23 package. Another alternative would be to
use a ceramic substrate or an aluminum core board such as
Thermal Clad . Using a board material such as Thermal
Clad, an aluminum core board, the power dissipation can be
doubled using the same footprint.
•
Mechanical stress or shock should not be applied during
cooling.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
Motorola Small–Signal Transistors, FETs and Diodes Device Data
3
PACKAGE DIMENSIONS
NOTES:
A
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
L
2. CONTROLLING DIMENSION: INCH.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD
FINISH THICKNESS. MINIMUM LEAD THICKNESS
IS THE MINIMUM THICKNESS OF BASE
MATERIAL.
3
S
B
1
2
INCHES
MIN MAX
MILLIMETERS
DIM
A
B
C
D
G
H
J
MIN
2.80
1.20
0.89
0.37
1.78
0.013
0.085
0.45
0.89
2.10
0.45
MAX
3.04
1.40
1.11
0.50
2.04
0.100
0.177
0.60
1.02
2.50
0.60
V
G
0.1102 0.1197
0.0472 0.0551
0.0350 0.0440
0.0150 0.0200
0.0701 0.0807
0.0005 0.0040
0.0034 0.0070
0.0180 0.0236
0.0350 0.0401
0.0830 0.0984
0.0177 0.0236
C
K
L
S
H
J
D
V
K
STYLE 9:
PIN 1. ANODE
STYLE 11:
PIN 1. ANODE
2. ANODE
2. CATHODE
3. CATHODE
3. CATHODE–ANODE
CASE 318–08
ISSUE AE
SOT–23 (TO–236AB)
STYLE 12:
STYLE 19:
PIN 1. CATHODE
PIN 1. CATHODE
2. CATHODE
3. ANODE
2. ANODE
3. CATHODE–ANODE
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
Opportunity/Affirmative Action Employer.
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315
Mfax : RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
– US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
INTERNET: http://motorola.com/sps
MMBD352LT1/D
◊
相关型号：
MMBD353LT1G
SILICON, UHF BAND, MIXER DIODE, TO-236AB, HALOGEN FREE AND ROHS COMPLIANT, CASE 318-08, 3 PIN
ROCHESTER
©2020 ICPDF网 联系我们和版权申明