MC74LCX05DT [MOTOROLA]
LOW-VOLTAGE CMOS HEX INVERTER OPEN DRAIN; 低电压CMOS六反相器开漏
| 型号： | MC74LCX05DT |
| 厂家： | 
MOTOROLA |
| 描述： | LOW-VOLTAGE CMOS HEX INVERTER OPEN DRAIN |
| 文件： | 总4页 (文件大小：119K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SEMICONDUCTOR TECHNICAL DATA
The MC74LCX05 is a high performance open drain hex inverter
operating from a 2.7 to 3.6V supply. High impedance TTL compatible
inputs significantly reduce current loading to input drivers. A V
specification of 5.5V allows MC74LCX05 inputs to be safely driven from
5V devices.
I
LOW–VOLTAGE CMOS
HEX INVERTER
The MC74LCX05 requires the addition of an external resistor to
perform a wire–NOR function. The open drain output with a 5V pull–up
resistor can be utlilized to drive 5V CMOS inputs. Current drive capability
is 24mA at the outputs.
OPEN DRAIN
• Designed for 2.7 to 3.6V V
CC
Operation
D SUFFIX
• 5V Tolerant Inputs — Interface Capability With 5V TTL Logic
• LVTTL Compatible
PLASTIC SOIC
CASE 751A–03
14
1
• LVCMOS Compatible
• 24mA Output Sink Capability
M SUFFIX
PLASTIC SOIC EIAJ
CASE 965–01
• Near Zero Static Supply Current (10µA) Substantially Reduces System
Power Requirements
14
1
• Latchup Performance Exceeds 500mA
• ESD Performance: Human Body Model >2000V; Machine Model >200V
SD SUFFIX
PLASTIC SSOP
CASE 940A–03
V
A3
13
O3
12
A4
11
O4
10
A5
9
O5
8
CC
14
14
14
1
1
Pinout: 14–Lead
(Top View)
DT SUFFIX
PLASTIC TSSOP
CASE 948G–01
1
2
3
4
5
6
7
A0
O0
A1
O1
A2
O2
GND
PIN NAMES
Pins
LOGIC DIAGRAM
Function
1
2
A0
O0
O1
O2
O3
O4
O5
An
On
Data Inputs
Outputs
3
4
6
A1
A2
A3
A4
A5
5
FUNCTION TABLE
An
On
13
11
9
12
10
8
L
H
H
L
This document contains information on a product under development. Motorola reserves the right to change or
discontinue this product without notice.
9/95
REV 0
1
Motorola, Inc. 1996
MC74LCX05
OUTLINE DIMENSIONS
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751A–03
ISSUE F
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
–A
–
14
1
8
7
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
–B
–
P 7 PL
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
M
M
0.25 (0.010)
B
MILLIMETERS
INCHES
G
F
R X 45°
DIM
A
B
C
D
F
G
J
MIN
8.55
3.80
1.35
0.35
0.40
MAX
8.75
4.00
1.75
0.49
1.25
MIN
MAX
0.344
0.157
0.068
0.019
0.049
C
0.337
0.150
0.054
0.014
0.016
J
M
SEATING
PLANE
K
D 14 PL
1.27 BSC
0.050 BSC
0.19
0.10
0.25
0.25
0.008
0.004
0.009
0.009
M
S
S
0.25 (0.010)
T
B
A
K
M
P
R
0
5.80
0.25
°
7
6.20
0.50
°
0
°
7°
0.244
0.019
0.228
0.010
M SUFFIX
PLASTIC SOIC EIAJ PACKAGE
CASE 965–01
ISSUE O
NOTES:
1
DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2
3
CONTROLLING DIMENSION: MILLIMETER.
DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH OR PROTRUSIONS AND ARE MEASURED
AT THE PARTING LINE. MOLD FLASH OR
PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006)
PER SIDE.
L
E
14
8
7
Q
1
E H
4
5
TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
E
M
THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
L
1
DETAIL P
Z
D
VIEW P
e
MILLIMETERS
INCHES
A
DIM
A
MIN
---
MAX
2.05
0.20
0.50
0.27
10.50
5.45
MIN
---
MAX
0.081
0.008
0.020
0.011
0.413
0.215
c
A
0.05
0.35
0.18
9.90
5.10
0.002
0.014
0.007
0.390
0.201
1
b
c
D
E
e
b
A
1
M
1.27 BSC
0.050 BSC
0.13 (0.005)
0.10 (0.004)
H
7.40
0.50
1.10
0
8.20
0.85
1.50
10
0.291
0.020
0.043
0
0.323
0.033
0.059
10
E
L
L
M
E
Q
Z
0.70
---
0.90
1.42
0.028
---
0.035
0.056
1
MOTOROLA
2
MC74LCX05
OUTLINE DIMENSIONS
SD SUFFIX
PLASTIC SSOP PACKAGE
CASE 940A–03
ISSUE B
14X K REF
0.12 (0.005)
NOTES:
M
S
S
T
U
V
0.25 (0.010)
6
DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
N
7
8
CONTROLLING DIMENSION: MILLIMETER.
DIMENSION A DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH
OR GATE BURRS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
14
8
7
L/2
M
9
DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.15 (0.006)
PER SIDE.
N
B
L
F
PIN 1
IDENT
10 DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION/INTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN
EXCESS OF K DIMENSION AT MAXIMUM
MATERIAL CONDITION. DAMBAR INTRUSION
SHALL NOT REDUCE DIMENSION K BY MORE
THAN 0.07 (0.002) AT LEAST MATERIAL
CONDITION.
1
DETAIL E
–U–
A
–V–
K
11 TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
12 DIMENSION A AND B ARE TO BE DETERMINED
AT DATUM PLANE –W–.
J
J1
M
S
0.20 (0.008)
T
U
K1
MILLIMETERS
INCHES
DIM
A
B
C
D
F
G
H
J
J1
K
MIN
6.07
5.20
1.73
0.05
0.63
MAX
6.33
5.38
1.99
0.21
0.95
MIN
MAX
0.249
0.212
0.078
0.008
0.037
SECTION N–N
0.238
0.205
0.068
0.002
0.024
–W–
0.65 BSC
0.026 BSC
C
0.076 (0.003)
1.08
0.09
0.09
0.25
0.25
7.65
0
1.22
0.20
0.16
0.38
0.33
7.90
8
0.042
0.003
0.003
0.010
0.010
0.301
0
0.048
0.008
0.006
0.015
0.013
0.311
8
SEATING
PLANE
–T–
D
G
DETAIL E
K1
L
M
H
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 948G–01
ISSUE O
NOTES:
14X K REF
1
DIMENSIONING AND TOLERANCING PER ANSI
M
S
S
Y14.5M, 1982.
0.10 (0.004)
T
U
V
2
3
CONTROLLING DIMENSION: MILLIMETER.
DIMENSION A DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH
OR GATE BURRS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED
0.25 (0.010) PER SIDE.
DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN
EXCESS OF THE K DIMENSION AT MAXIMUM
MATERIAL CONDITION.
S
0.15 (0.006) T
U
N
0.25 (0.010)
14
4
5
8
2X L/2
M
B
L
N
–U–
PIN 1
IDENT.
F
7
1
6
7
TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
DIMENSION A AND B ARE TO BE DETERMINED
AT DATUM PLANE –W–.
DETAIL E
S
K
0.15 (0.006) T
U
A
MILLIMETERS
INCHES
K1
DIM
A
B
C
D
F
G
H
J
J1
K
MIN
4.90
4.30
–––
0.05
0.50
MAX
5.10
4.50
1.20
0.15
0.75
MIN
MAX
0.200
0.177
0.047
0.006
0.030
–V–
0.193
0.169
–––
0.002
0.020
J J1
SECTION N–N
0.65 BSC
0.026 BSC
0.50
0.09
0.09
0.19
0.19
0.60
0.20
0.16
0.30
0.25
0.020
0.004
0.004
0.007
0.007
0.024
0.008
0.006
0.012
0.010
–W–
C
K1
L
6.40 BSC
0.252 BSC
0.10 (0.004)
M
0
8
0
8
SEATING
PLANE
–T–
H
G
DETAIL E
D
3
MOTOROLA
MC74LCX05
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
Opportunity/Affirmative Action Employer.
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
Mfax : RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MC74LCX05/D
◊
相关型号：
MC74LCX05M
IC LVC/LCX/Z SERIES, HEX 1-INPUT INVERT GATE, PDSO14, EIAJ, PLASTIC, SOIC-14, Gate
ONSEMI
MC74LCX05MEL
IC LVC/LCX/Z SERIES, HEX 1-INPUT INVERT GATE, PDSO14, EIAJ, PLASTIC, SOIC-14, Gate
ONSEMI
©2020 ICPDF网 联系我们和版权申明