MC33341P [MOTOROLA]
POWER SUPPLY BATTERY CHARGER REGULATION CONTROL CIRCUIT; 电源电池充电器调节控制电路
| 型号： | MC33341P |
| 厂家： | 
MOTOROLA |
| 描述： | POWER SUPPLY BATTERY CHARGER REGULATION CONTROL CIRCUIT |
| 文件： | 总20页 (文件大小：377K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Order this document by MC33341/D
POWER SUPPLY
BATTERY CHARGER
REGULATION
The MC33341 is a monolithic regulation control circuit that is specifically
designed to close the voltage and current feedback loops in power supply
and battery charger applications. This device features the unique ability to
perform source high–side, load high–side, source low–side and load
low–side current sensing, each with either an internally fixed or externally
adjustable threshold. The various current sensing modes are accomplished
by a means of selectively using the internal differential amplifier, inverting
amplifier, or a direct input path. Positive voltage sensing is performed by an
internal voltage amplifier. The voltage amplifier threshold is internally fixed
and can be externally adjusted in all low–side current sensing applications.
An active high drive output is provided to directly interface with economical
optoisolators for isolated output power systems. This device is available in
8–lead dual–in–line and surface mount packages.
CONTROL CIRCUIT
SEMICONDUCTOR
TECHNICAL DATA
8
1
• Differential Amplifier for High–Side Source and Load Current Sensing
• Inverting Amplifier for Source Return Low–Side Current Sensing
• Non–Inverting Input Path for Load Low–Side Current Sensing
• Fixed or Adjustable Current Threshold in All Current Sensing Modes
• Positive Voltage Sensing in All Current Sensing Modes
P SUFFIX
PLASTIC PACKAGE
CASE 626
• Fixed Voltage Threshold in All Current Sensing Modes
8
• Adjustable Voltage Threshold in All Low–Side Current Sensing Modes
• Output Driver Directly Interfaces with Economical Optoisolators
• Operating Voltage Range of 2.3 V to 16 V
1
D SUFFIX
PLASTIC PACKAGE
CASE 751
Representative Block Diagram
(SO–8)
Current Sense Input B/
Voltage Threshold Adjust
Drive
Output
Voltage Sense
Input
V
CC
7
8
6
5
PIN CONNECTIONS
Current Sense
Differential
Amp
Drive Output
1
2
3
4
8
7
6
5
Input A
Voltage and Current
Transconductance
Amp/Driver
1.0
Current Threshold
Adjust
V
CC
V
Current Sense Input B/
Voltage Threshold Adjust
Compensation
Gnd
1.2 V
0.2 V
1.0
I
Voltage Sense Input
Inverting/
Noninverting Amp
Reference
(Top View)
ORDERING INFORMATION
Operating
1
2
3
4
Temperature Range
Device
Package
Current Sense
Input A
Current
Threshold Adjust
Compensation
Gnd
MC33341D
MC33341P
SO–8
T
= –25° to +85°C
A
This device contains 114 active transistors.
Plastic DIP
This document contains information on a new product. Specifications and information herein
Motorola, Inc. 1996
Rev 0
are subject to change without notice.
MC33341
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
V
Power Supply Voltage (Pin 7)
V
CC
16
Voltage Range
V
IR
–1.0 to V
V
CC
Current Sense Input A (Pin 1)
Current Threshold Adjust (Pin 2)
Compensation (Pin 3)
Voltage Sense Input (Pin 5)
Current Sense Input B/Voltage Threshold Adjust (Pin 6)
Drive Output (Pin 8)
Drive Output Source Current (Pin 8)
I
50
mA
Source
Thermal Resistance, Junction–to–Air
P Suffix, DIP Plastic Package, Case 626
D Suffix, SO–8 Plastic Package, Case 751
R
°C/W
θJA
100
178
Operating Junction Temperature (Note 1)
Storage Temperature
T
–25 to +150
–55 to +150
°C
°C
J
T
stg
NOTE: ESD data available upon request.
ELECTRICAL CHARACTERISTICS (V
CC
= 6.0 V, T = 25°C, for min/max values T is the operating junction
A A
temperature range that applies (Note 1), unless otherwise noted.)
Characteristic
Symbol
Min
Typ
Max
Unit
CURRENT SENSING (Pins 1, 2, 6)
High–Side Source and Load Sensing Pin 1 to Pin 6 (Pin 1 >1.6 V)
V
mV
th(I HS)
th(I LS+)
th(I LS–)
Internally Fixed Threshold Voltage (Pin 2 = V
)
CC
T
A
= 25°C
187
183
–
197
–
10
207
211
–
T
A
= T
to T
low high
Externally Adjusted Threshold Voltage (Pin 2 = 0 V)
Externally Adjusted Threshold Voltage (Pin 2 = 200 mV)
–
180
–
Low–Side Load Sensing Pin 1 to Pin 4 (Pin 1 = 0 V to 0.8 V)
V
V
mV
mV
Internally Fixed Threshold Voltage (Pin 2 = V
)
CC
T
A
= 25°C
194
192
–
200
–
10
206
208
–
T
A
= T
to T
low high
Externally Adjusted Threshold Voltage (Pin 2 = 0 V)
Externally Adjusted Threshold Voltage (Pin 2 = 200 mV)
–
180
–
Low–Side Source Return Sensing Pin 1 to 4 (Pin 1 = 0 V to –0.2 V)
Internally Fixed Threshold Voltage (Pin 2 = V
)
CC
T
= 25°C
–195
–193
–
–201
–
–10
–180
–207
–209
–
A
T
= T
to T
A
low high
Externally Adjusted Threshold Voltage (Pin 2 = 0 V)
Externally Adjusted Threshold Voltage (Pin 2 = 200 mV)
–
–
Current Sense Input A (Pin 1)
Input Bias Current, High–Side Source and Load Sensing
I
–
–
–
40
10
10
–
–
–
µA
nA
kΩ
IB(A HS)
(Pin 2 = 0 V to V
V)
Pin 6
Input Bias Current, Low–Side Load Sensing
(Pin 2 = 0 V to 0.8 V)
I
IB(A LS+)
Input Resistance, Low–Side Source Return Sensing
(Pin 2 = –0.6 V to 0 V)
R
in(A LS–)
Current Sense Input B/Voltage Threshold Adjust (Pin 6)
Input Bias Current
I
IB(B)
High–Side Source and Load Current Sensing (Pin 6 > 2.0 V)
Voltage Threshold Adjust (Pin 6 < 1.2 V)
–
–
20
100
–
–
µA
nA
Current Sense Threshold Adjust (Pin 2)
Input Bias Current
I
–
10
–
nA
IB(I th)
Transconductance, Current Sensing Inputs to Drive Output
g
m(I)
–
6.0
–
mhos
NOTE: 1. Tested ambient temperature range for the MC33341: T
= –25°C, T
= +85°C.
high
low
2
MOTOROLA ANALOG IC DEVICE DATA
MC33341
ELECTRICAL CHARACTERISTICS (continued) (V
temperature range that applies (Note 1), unless otherwise noted.)
= 6.0 V, T = 25°C, for min/max values T is the operating junction
CC
A
A
Characteristic
Symbol
Min
Typ
Max
Unit
DIFFERENTIAL AMPLIFIER DISABLE LOGIC (Pins 1, 6)
Logic Threshold Voltage Pin 1 (Pin 6 = 0 V)
V
Enabled, High–Side Source and Load Current Sensing
Disabled, Low–Side Load and Source Return Current Sensing
V
V
–
–
≥1.7
≤1.3
–
–
th(I HS)
th(I LS)
VOLTAGE SENSING (Pins 5, 6)
Positive Sensing Pin 5 to Pin 4
V
th(V)
Internally Fixed Threshold Voltage
T
= 25°C
1.186
1.174
–
1.210
–
40
1.234
1.246
–
V
V
mV
V
A
T
= T
to T
A
low high
Externally Adjusted Threshold Voltage (Pin 6 = 0 V)
Externally Adjusted Threshold Voltage (Pin 6 = 1.2 V)
–
1.175
–
Voltage Sense, Input Bias Current (Pin 5)
Transconductance, Voltage Sensing Inputs to Drive Output
DRIVE OUTPUT (Pin 8)
I
–
–
10
–
–
nA
IB(V)
g
7.0
mhos
m(V)
High State Source Voltage (I
= 10 mA)
V
–
V
– 0.8
CC
20
–
–
V
Source
OH
High State Source Current (Pin 8 = 0 V)
TOTAL DEVICE (Pin 7)
I
15
mA
Source
Operating Voltage Range
V
2.5 to 15
–
2.3 to 15
300
–
V
CC
Power Supply Current (V
= 6.0 V)
I
600
µA
CC
CC
NOTE: 1. Tested ambient temperature range for the MC33341: T
low
= –25°C, T
= +85°C.
high
PIN FUNCTION DESCRIPTION
Pin
Name
Description
1
Current Sense Input A
This multi–mode current sensing input can be used for either source high–side, load high–side,
source–return low–side, or load low–side sensing. It is common to a Differential Amplifier, Inverting
Amplifier, and a Noninverting input path. Each of these sensing paths indirectly connect to the current
sense input of the Transconductance Amplifier. This input is connected to the high potential side of a
current sense resistor when used in source high–side, load high–side, or load low–side current
sensing modes. In source return low–side current sensing mode, this pin connects to the low potential
side of a current sense resistor.
2
3
Current Threshold Adjust
Compensation
The current sense threshold can be externally adjusted over a range of 0 V to 200 mV with respect to
Pin 4, or internally fixed at 200 mV by connecting Pin 2 to V
.
CC
This pin is connected to a high impedance node within the transconductance amplifier and is made
available for loop compensation. It can also be used as an input to directly control the Drive Output.
An active low at this pin will force the Drive Output into a high state.
4
5
Ground
This pin is the regulation control IC ground. The control threshold voltages are with respect to this pin.
Voltage Sense Input
This is the voltage sensing input of the Transconductance Amplifier. It is normally connected to the
power supply/battery charger output through a resistor divider. The input threshold is controlled by
Pin 6.
6
Current Sense Input B/
Voltage Threshold Adjust
This is a dual function input that is used for either high–side current sensing, or as a voltage threshold
adjustment for Pin 5. This input is connected to the low potential side of a current sense resistor when
used in source high–side or load high–side current sensing modes. In all low–side current sensing
modes, Pin 6 is available as a voltage threshold adjustment for Pin 5. The threshold can be externally
adjusted over a range of 0 V to 1.2 V with respect to Pin 4, or internally fixed at 1.2 V by connecting
Pin 6 to V
.
CC
7
8
V
This is the positive supply voltage for the regulation control IC. The typical operating voltage range is
2.3 V to 15 V with respect to Pin 4.
CC
Drive Output
This is a source–only output that normally connects to a linear or switching regulator control circuit.
This output is capable of 15 mA, allowing it to directly drive an optoisolator in primary side control
applications where galvanic isolation is required.
3
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 2. Current Sensing
Figure 1. Voltage Sensing
Threshold Change versus Temperature
Threshold Change versus Temperature
4.0
1.0
V
= 6.0 V
V
= 6.0 V
CC
CC
0
0
–4.0
–1.0
3
2
1
–8.0
–12
–2.0
–3.0
1 – Source High–Side and Load High–Side
2 – Source Return Low–Side
3 – Load Low–Side
–50
–25
0
25
50
75
C)
100
125
–50
–25
0
25
50
75
C)
100
125
T , AMBIENT TEMPERATURE (
°
T , AMBIENT TEMPERATURE (
°
A
A
Figure 3. Closed–Loop Voltage Sensing Input
versus Voltage Threshold Adjust
Figure 4. Closed–Loop Current Sense Input B
versus Current Threshold Adjust
1.6
1.4
1.2
1.0
0.8
0.6
0
16
0
V
V
I
= 6.0 V
= 1.0 V
= 1.0 mA
= 25°C
CC
O
O
A
V
CC
14
12
10
8.0
–40
–80
2.0
4.0
6.0
8.0
10
V
–V
Pin 1 Pin 6
T
V
V
I
= 6.0 V
= 1.0 V
= 1.0 mA
CC
O
O
V
Pin 6
–120
Pin 1 = V
T
V
CC
Pin 5
= 25
°C
A
–160
–200
–240
–280
6.0
4.0
2.0
0
Differential Amplifier is active for
source high–side and load high–side
current sensing. Both vertical axis are
0.4
0.2
0
12
V
–V
Pin 6 Pin 5
expressed in millivolts down to V
.
CC
14
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
0
40
80
120
160
200
240
280
V , VOLTAGE THRESHOLD ADJUST (V)
Pin 6
V , CURRENT THRESHOLD ADJUST (V)
Pin 2
Figure 5. Closed–Loop Current Sensing Input A
versus Current Threshold Adjust
Figure 6. Closed–Loop Current Sensing Input A
versus Current Threshold Adjust
280
240
200
160
120
80
0
–40
14
12
10
14
12
10
Noninverting input path is active
for load low–side current sensing.
V
V
I
= 6.0 V
= 1.0 V
= 1.0 mA
= 25°C
CC
O
O
A
Gnd
V
V
V
= 6.0 V
= 1.0 V
= 1.0 mA
Pin 5
CC
O
–80
T
I
O
T
= 25
°C
–120
–160
–200
8.0
6.0
4.0
8.0
6.0
4.0
A
V
Pin 5
V
–|V |
Pin 2 Pin 1
V
–V
Pin 2 Pin 1
Inverting Amplifier is
40
0
–240
–260
2.0
0
active for source return
low–side current sensing.
2.0
0
Gnd
240
0
40
80
120
160
200
280
0
40
80
120
160
200
240
280
V
, CURRENT THRESHOLD ADJUST (mV)
V , CURRENT THRESHOLD ADJUST (mV)
Pin 2
Pin 2
4
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 8. Bode Plot
Figure 7. Bode Plot
Current Sensing Inputs to Drive Output
Voltage Sensing Inputs to Drive Output
60
50
40
60
50
40
30
20
10
0
80
80
Phase
Low–Side Sensing
Phase
High–Side Sensing
Phase
100
120
100
120
Gain
30
20
10
0
Gain
140
160
180
140
160
180
V
V
R
= 6.0 V
= 1.0 V
= 1.0 k
V
V
= 6.0 V
CC
CC
= 1.0 V
R = 1.0 k
L
O
L
O
Pin 3 = 1.0 nF
= 25
Pin 3 = 1.8 nF
= 25
T
°C
T
°C
A
A
1.0 k
1.0 k
10 k
100 k
1.0 M
10 k
100 k
1.0 M
f, FREQUENCY (Hz)
f, FREQUENCY (Hz)
Figure 9. Transconductance
Voltage Sensing Inputs to Drive Output
Figure 10. Transconductance
Current Sensing Inputs to Drive Output
8.0
6.0
8.0
6.0
V
V
T
= 6.0 V
= 1.0 V
V
= 6.0 V
CC
O
CC
V = 1.0 V
O
= 25
°C
T = 25°C
A
A
4.0
4.0
2.0
0
2.0
0
0.1
0.2 0.3
0.5
1.0
2.0 3.0
5.0
10
0.1
0.2 0.3
0.5
1.0
2.0 3.0
5.0
10
I
, DRIVE OUTPUT LOAD CURRENT (mA)
I
, DRIVE OUTPUT LOAD CURRENT (mA)
O
O
Figure 11. Drive Output High State
Source Saturation versus Load Current
Figure 12. Supply Current
versus Supply Voltage
0
–0.4
–0.8
–1.2
–1.6
–2.0
1.0
0.8
0.6
0.4
0.2
0
V
T
= 6.0 V
CC
= 25°C
Drive Output High State
V
CC
A
I
T
= 0 mA
O
= 25°C
A
Drive Output Low State
0
4.0
8.0
12
16
20
0
4.0
8.0
, SUPPLY VOLTAGE (V)
CC
12
16
I , OUTPUT LOAD CURRENT (mA)
V
L
5
MOTOROLA ANALOG IC DEVICE DATA
MC33341
noninverting I
input of the transconductance amplifier. In
INTRODUCTION
sen
order to allow for maximum circuit flexibility, there are three
methods of current sensing, each with different internal
paths.
In source high–side (Figures 13 and 14)andloadhigh–side
(Figures 17 and 18) current sensing, the Differential Amplifier
is active with a gain of 1.0. Pin 1 connects to the high potential
Power supplies and battery chargers require precise
control of output voltage and current in order to prevent
catastrophic damage to the system load. Many present day
power sources contain a wide assortment of building blocks
and glue devices to perform the required sensing for proper
regulation. Typical feedback loop circuits may consist of a
voltage and current amplifier, level shifting circuitry, summing
circuitry and a reference. The MC33341 contains all of these
basic functions in a manner that is easily adaptable to many
of the various power source–load configurations.
side of current sense resistor R while Pin 6 connects to the
S
low side. Logic circuitry is provided to disable the Differential
Amplifier output whenever low–side current sensing is
required. This circuit clamps the Differential Amplifier output
high which disconnects it from the I
TransconductanceAmplifier. This happens if Pin 1 is lessthan
1.2 V or if Pin 1 is less than Pin 6.
input of the
sen
OPERATING DESCRIPTION
The MC33341 is an analog regulation control circuit that is
specifically designed to simultaneously close the voltage and
current feedback loops in power supply and battery charger
applications. This device can control the feedback loop in
either constant–voltage or constant–current mode with
automatic crossover. A concise description of the integrated
circuit blocks is given below. Refer to the block diagram in
Figure 13.
With source return low–side current sensing (Figures 15
and 16), the Inverting Amplifier is active with a gain of –1.0.
Pin 1 connects to the low potential side of current sense
resistor R while Pin 4 connects to the high side. Note that a
S
negative voltage appears across R with respect to Pin 4.
S
In load low–side current sensing (Figures 19 and 20) a
Noninverting input path is active with a gain of 1.0. Pin 1
connects to the high potential side of current sense resistor
Transconductance Amplifier
R
while Pin 4 connects to the low side. The Noninverting
S
A quad input transconductance amplifier is used to control
the feedback loop. This amplifier has separate voltage and
current channels, each with a sense and a threshold input.
Within a given channel, if the sense input level exceeds that
of the threshold input, the amplifier output is driven high. The
channel with the largest difference between the sense and
threshold inputs will set the output source current of the
amplifier and thus dominate control of the feedback loop. The
amplifier output appears at Pin 8 and is a source–only type
that is capable of 15 mA.
A high impedance node within the transconductance
amplifier is made available at Pin 3 for loop compensation.
This pin can sink and source up to 10 µA of current. System
stability is achieved by connecting a capacitor from Pin 3 to
ground. The Compensation Pin signal is out of phase with
respect to the Drive Output. By actively clamping Pin 3 low,
the Drive Output is forced into a high state. This, in effect, will
shutdown the power supply or battery charger, by forcing the
output voltage and current regulation threshold down
towards zero.
input path lies from Pin 1, through the Inverting Amplifier
input and feedback resistors R, to the cathode of the output
diode. With load low–side current sensing, Pin 1 will be more
positive than Pin 4, forcing the Inverting Amplifier output low.
This causes the diode to be reverse biased, thus preventing
the output stage of the amplifier from loading the input signal
that is flowing through the feedback resistors.
The regulation threshold in all of the current sensing
modes is internally fixed at 200 mV with Pin 2 connected to
V
. Pin 2 can be used to externally adjust the threshold over
CC
a range of 0 to 200 mV with respect to the IC ground at Pin 4.
Reference
An internal band gap reference is used to set the 1.2 V
voltage threshold and 200 mV current threshold. The
reference is initially trimmed to a ±1.0% tolerance at
T
= 25°C and is guaranteed to be within ±2.0% over an
A
ambient operating temperature range of –25° to 85°C.
Applications
Each of the application circuits illustrate the flexibility of
this device. The circuits shown in Figures 13 through 20
contain an optoisolator connected from the Drive Output at
Pin 8 to ground. This configuration is shown for ease of
understanding and would normally be used to provide an
isolated control signal to a primary side switching regulator
controller. In non–isolated, primary or secondary side
applications, a load resistor can be placed from Pin 8 to
ground. This resistor will convert the Drive Output current to
a voltage for direct control of a regulator.
Voltage Sensing
The voltage that appears across the load is monitored by
the noninverting V
This voltage is resistively scaled down and connected to
Pin 5. The threshold at which voltage regulation occurs is set
by the level present at the inverting V
transconductance amplifier. This level is controlled by Pin 6.
In source high–side and load high–side current sensing
modes, Pin 6 must be connected to the low potential side of
input of the transconductance amplifier.
sen
input of the
th
current sense resistor R . Under these conditions, the
In applications where excessively high peak currents are
possible from the source or load, the load induced voltage
S
voltage regulation threshold is internally fixed at 1.2 V. In
source return low–side and load low–side current sensing
modes, Pin 6 is available, and can be used to lower the
regulation threshold of Pin 5. This threshold can be externally
adjusted over a range of 0 V to 1.2 V with respect to the IC
ground at Pin 4.
drop across R could exceed 1.6 V. Depending upon the
S
current sensing configuration used, this will result in forward
biasing of either the internal V
clamp diode, Pin 6, or the
CC
device substrate, Pin 1. Under these conditions, input series
resistor R3 is required. The peak input current should be
limited to 20 mA. Excessively large values for R3 will
degrade the current sensing accuracy. Figure 21 shows a
Current Sensing
Current sensing is accomplished by monitoring the
method of bounding the voltage drop across R without
S
voltage that appears across sense resistor R level shifting
S,
sacrificing current sensing accuracy.
it with respect to Pin 4 if required, and applying it to the
6
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 13. Source High–Side Current Sensing with
Internally Fixed Voltage and Current Thresholds
R
S
Source
Load
R2
R3
8
7
6
5
V
V
CC
CC
V
CC
V
CC
R1
1.2 V
Differential Amp
Disable Logic
1.2 V
V
0.4 V
sen
Transconductance
Amp
Opto
Isolator
V
V
CC
V
th
V
Differential Amp
R
I
sen
R
R
I
I
th
V
CC
R
R
Reference
Battery or
Resistive
Load
CC
V
R
CC
0.2 V 0.4 V 1.2 V
V
CC
0.2 V
Inverting Amp
1
2
3
4
Comp
Source
Return
Load
The above figure shows the MC33341 configured for source high–side current sensing allowing a common ground path
between Load – and Source Return –. The Differential Amplifier inputs, Pins 1 and 6, are used to sense the load induced
voltage drop that appears across resistor R . The internal voltage and current regulation thresholds are selected by the
S
respective external connections of Pins 2 and 6. Resistor R3 is required in applications where a high peak level of reverse
current is possible if the source inputs are shorted. The resistor value should be chosen to limit the input current of the internal
V
clamp diode to less than 20 mA. Excessively large values for R3 will degrade the current sensing accuracy.
CC
V
R2
R1
th(I HS)
V
V
1
I
R
– 0.6
reg
th(V)
I
pk
S
reg
R
R3
S
0.02
0.2
R2
R1
1.2
1
R
S
7
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 14. Source High–Side Current Sensing with
Externally Adjustable Current and Internally Fixed Voltage Thresholds
R
S
Source
Load
R2
R3
8
7
6
5
V
V
CC
CC
V
CC
V
CC
R1
1.2 V
Differential Amp
Disable Logic
1.2 V
V
0.4 V
sen
Transconductance
Amp
Opto
Isolator
V
V
CC
V
th
V
Differential Amp
R
I
sen
R
R
I
I
th
V
CC
R
R
Reference
Battery or
Resistive
Load
CC
V
R
CC
0.2 V 0.4 V 1.2 V
V
CC
0.2 V
Inverting Amp
1
2
3
4
Current
Control
Comp
Source
Return
Load
The above figure shows the MC33341 configured for source high–side current sensing with an externally adjustable current
threshold. Operation of this circuit is similar to that of Figure 13. The current regulation threshold can be adjusted over a range
of 0 V to 200 mV with respect to Pin 4.
V
R2
R1
th(Pin 2)
V
V
1
I
R
– 0.6
reg
th(V)
I
pk
S
reg
R
R3
S
0.02
R2
R1
1.2
1
8
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 15. Source Return Low–Side Current Sensing with
Internally Fixed Current and Voltage Thresholds
Source
Load
R2
8
7
6
5
V
V
CC
CC
V
CC
V
CC
R1
1.2 V
Differential Amp
Disable Logic
1.2 V
V
0.4 V
sen
Transconductance
Amp
Opto
Isolator
V
V
CC
V
th
V
Differential Amp
R
I
sen
R
R
I
I
th
V
CC
R
R
Reference
Battery or
Resistive
Load
CC
V
R
CC
0.2 V 0.4 V 1.2 V
V
CC
0.2 V
Inverting Amp
1
2
3
4
Comp
R3
R
Source
Return
S
Load
The above figure shows the MC33341 configured for source return low–side current sensing allowing a common power path
between Source + and Load +. This configuration is especially suited for negative output applications where a common ground
path, Source + to Load +, is desired. The Inverting Amplifier inputs, Pins 1 and 4, are used to sense the load induced voltage
drop that appears across resistor R . The internal voltage and current regulation thresholds are selected by the respective
S
external connections of Pins 2 and 6. Resistor R3 is required in applications where high peak levels of inrush current are
possible. The resistor value should be chosen to limit the negative substrate current to less than 20 mA. Excessively large
values for R3 will degrade the current sensing accuracy.
V
R2
R1
th(I LS–)
V
V
1
I
R
– 0.6
reg
th(V)
I
pk
S
reg
R
R3
S
0.02
–0.2
R2
R1
1.2
1
R
S
9
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 16. Source Return Low–Side Current Sensing with
Externally Adjustable Current and Voltage Thresholds
Source
Load
R2
Voltage
Control
8
7
6
5
V
V
CC
CC
V
CC
V
CC
R1
1.2 V
Differential Amp
Disable Logic
1.2 V
V
0.4 V
sen
Transconductance
Amp
Opto
Isolator
V
V
CC
V
th
V
Differential Amp
R
I
sen
R
R
I
I
th
V
CC
R
R
Reference
Battery or
Resistive
Load
CC
V
R
CC
0.2 V 0.4 V 1.2 V
V
CC
0.2 V
Inverting Amp
1
2
3
4
Current
Control
Comp
R3
R
Source
Return
S
Load
The above figure shows the MC33341 configured for source return low–side current sensing with externally adjustable voltage
and current thresholds. Operation of this circuit is similar to that of Figure 15. The respective voltage and current regulation
threshold can be adjusted over a range of 0 to 1.6 V and 0 V to 200 mV with respect to Pin 4.
V
R2
R1
th(Pin 2)
V
V
1
I
R
– 0.6
reg
th(Pin 6)
I
–
pk
S
reg
R
R3
S
0.02
10
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 17. Load High–Side Current Sensing with
Internally Fixed Current and Voltage Thresholds
Source
Load
R
R2
S
R3
8
7
6
5
V
V
CC
CC
V
CC
V
CC
R1
1.2 V
Differential Amp
Disable Logic
1.2 V
V
0.4 V
sen
Transconductance
Amp
Opto
Isolator
V
V
CC
V
th
V
Differential Amp
R
I
sen
R
R
I
I
th
V
CC
R
R
Reference
Battery or
Resistive
Load
CC
V
R
CC
0.2 V 0.4 V 1.2 V
V
CC
0.2 V
Inverting Amp
1
2
3
4
Comp
Source
Return
Load
The above figure shows the MC33341 configured for load high–side current sensing allowing common paths for both power
and ground, between the source and load. The Differential Amplifier inputs, Pins 1 and 6, are used to sense the load induced
voltage drop that appears across resistor R . The internal voltage and current regulation thresholds are selected by the
S
respective external connections of Pins 2 and 6. Resistor R3 is required in applications where high peak levels of load current
are possible from the battery or load bypass capacitor. The resistor value should be chosen to limit the input current of the
internal V
clamp diode to less than 20 mA. Excessively large values for R3 ill degrade the current sensing accuracy.
CC
V
R2
R1
th(I HS)
V
V
1
I
R
– 0.6
reg
th(V)
I
pk
S
reg
R
R3
S
0.02
0.2
R2
R1
1.2
1
R
S
11
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 18. Load High–Side Current Sensing with
Externally Adjustable Current and Internally Fixed Voltage Thresholds
Source
Load
R2
R
S
R3
8
7
6
5
V
V
CC
CC
V
CC
V
CC
R1
1.2 V
Differential Amp
Disable Logic
1.2 V
V
0.4 V
sen
Transconductance
Amp
Opto
Isolator
V
V
CC
V
th
V
Differential Amp
R
I
sen
R
R
I
I
th
V
CC
R
R
Reference
Battery or
Resistive
Load
CC
V
R
CC
0.2 V 0.4 V 1.2 V
V
CC
0.2 V
Inverting Amp
1
2
3
4
Current
Control
Comp
Source
Return
Load
The above figure shows the MC33341 configured for load high–side current sensing with an externally adjustable current
threshold. Operation of this circuit is similar to that of Figure 17. The current regulation threshold can be adjusted over a range
of 0 V to 200 mV with respect to Pin 4.
V
R2
R1
th(Pin 2)
V
V
1
I
R
– 0.6
reg
th(V)
I
pk
S
reg
R
R3
S
0.02
R2
R1
1.2
1
12
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 19. Load Low–Side Current Sensing with
Internally Fixed Current and Voltage Thresholds
Source
Load
R2
8
7
6
5
V
V
CC
CC
V
CC
V
CC
R1
1.2 V
Differential Amp
Disable Logic
1.2 V
V
0.4 V
sen
Transconductance
Amp
Opto
Isolator
V
V
CC
V
th
V
Differential Amp
R
I
sen
R
R
I
I
th
V
CC
R
R
Reference
Battery or
Resistive
Load
CC
V
R
CC
0.2 V 0.4 V 1.2 V
V
CC
0.2 V
Inverting Amp
1
2
3
4
R3
R
Comp
S
Source
Return
Load
The above figure shows the MC33341 configured for load low–side current sensing allowing common paths for both power and
ground, between the source and load. The Noninverting input paths, Pins 1 and 4, are used to sense the load induced voltage
drop that appears across resistor R . The internal voltage and current regulation thresholds are selected by the respective
S
external connections of Pins 2 and 6. Resistor R3 is required in applications where high peak levels of load current are possible
from the battery or load bypass capacitor. The resistor value should be chosen to limit the negative substratecurrent to less than
20 mA. Excessively large values for R3 will degrade the current sensing accuracy.
V
R2
R1
th(I LS
)
V
V
1
I
R
– 0.6
reg
th(V)
I
pk
S
reg
R
R3
S
0.02
0.2
R2
R1
1.2
1
R
S
13
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 20. Load Low–Side Current Sensing with
Externally Adjustable Current and Voltage Thresholds
Source
Load
R2
Voltage
Current
8
7
6
5
V
V
CC
CC
V
CC
V
CC
R1
1.2 V
Differential Amp
Disable Logic
1.2 V
V
0.4 V
sen
Transconductance
Amp
Opto
Isolator
V
V
CC
V
th
V
Differential Amp
R
I
sen
R
R
I
I
th
V
CC
R
R
Reference
Battery or
Resistive
Load
CC
V
R
CC
0.2 V 0.4 V 1.2 V
V
CC
0.2 V
Inverting Amp
1
2
3
4
R3
Current
Control
R
S
Comp
Source
Return
Load
The above figure shows the MC33341 configured for load low–side current sensing with an externally adjustable voltage and
current threshold. Operation of this circuit is similar to that of Figure 19. The respective voltage and current regulation threshold
can be adjusted over a range of 0 to 1.2 V and 0 V to 200 mV, with respect to Pin 4.
V
R2
R1
th(Pin 2)
V
V
1
I
R
– 0.6
reg
th(Pin 6)
I
pk
S
reg
R
R3
S
0.02
14
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 21. Current Sense Resistor Bounding
Source
Load
R
S
8
1
7
6
5
4
Input
Short
Output
Short
MC33341
2
3
Source
Return
Load
NOTE: An excessive load induced voltage across R can occur if either the source input or load output is shorted. This voltage can
S
easily be bounded with the addition of the diodes shown without degrading the current sensing accuracy. This bounding technique
can be used in any of the MC33341 applications where high peak currents are anticipated.
Figure 22. Multiple Output Current and Voltage Regulation
Source
Load
Load
Load
Output 2
8
1
7
6
5
4
MC33341
2
3
Source
Output 1
Opto
Isolator
8
1
7
6
5
4
MC33341
2
3
Source
Return
Output Common
NOTE: Multiple outputs can be controlled by summing the error signal into a common optoisolator. The converter output with the largest
voltage or current error will dominate control of the feedback loop.
15
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 23. 10 V/1.0 A Constant–Voltage Constant–Current Regulator
0.2
MTP2955
Input
Output
12 V to 16 V
10 V/1.0 A
82.5 k
8
7
6
5
V
V
CC
CC
V
CC
V
CC
11.1 k
1.2 V
Differential Amp
Disable Logic
1.2 V
V
0.4 V
sen
Transconductance
Amp
V
V
10
10
CC
V
th
V
Differential Amp
R
I
sen
R
R
I
I
th
V
CC
R
R
Reference
Variable
Resistive
Load
CC
V
R
CC
0.2 V 0.4 V 1.2 V
V
CC
0.2 V
Inverting Amp
1
2
3
4
0.01
3.0 k
Input
Ground
Output
Ground
Figure 24. Output Load Regulation
10
8.0
6.0
4.0
2.0
0
0
0.2
0 4
0.6
0.8
1.0
I
, OUTPUT LOAD CURRENT (A)
O
Figure 23 shows the MC33341 configured as a source high–side constant–voltage constant–current regulator. The regulator is
designed for an output voltage of 10 V at 1.0 A. Figure 24 shows the regulator’s output characteristics as the load is varied.
Source return low–side, load high–side, and load low–side configurations will each exhibit a nearly identical load regulation
characteristic. A heatsink is required for the MTP2955 series pass element.
16
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Figure 25. Constant–Current Constant–Voltage Switch Mode Charger
200 µH
MTP2955
0.25
Input
12 V
Output
5.87 V/800 mA
1N5821
100
68 k
3.0 k
8
7
6
5
V
V
CC
CC
V
CC
V
CC
1.2 V
Differential Amp
Disable Logic
1.2 V
V
0.4 V
sen
Transconductance
Amp
V
V
100
CC
V
th
V
Differential Amp
R
I
sen
R
R
I
I
th
V
CC
R
R
Reference
CC
V
R
CC
0.2 V 0.4 V 1.2 V
V
CC
0.2 V
Inverting Amp
1
2
3
4
12 k
Input
Ground
Output
Ground
Figure 25 shows that the MC33341 can be configured as a high–side constant–current constant–voltage switch mode charger.
This circuit operates as a step down converter. With a nominal input voltage and output load current as stated above, the
switching frequency is approximately 28 kHz with and an associated conversion efficiency of 86 percent. The switching fre-
quency will vary with changes in input voltage and load current.
17
MOTOROLA ANALOG IC DEVICE DATA
MC33341
OUTLINE DIMENSIONS
P SUFFIX
PLASTIC PACKAGE
CASE 626–05
ISSUE K
8
5
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
–B–
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
1
4
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
F
MILLIMETERS
INCHES
–A–
NOTE 2
DIM
A
B
C
D
F
G
H
J
K
L
M
N
MIN
9.40
6.10
3.94
0.38
1.02
MAX
10.16
6.60
4.45
0.51
1.78
MIN
MAX
0.400
0.260
0.175
0.020
0.070
L
0.370
0.240
0.155
0.015
0.040
C
2.54 BSC
0.100 BSC
0.76
0.20
2.92
1.27
0.30
3.43
0.030
0.008
0.115
0.050
0.012
0.135
J
–T–
SEATING
PLANE
N
7.62 BSC
0.300 BSC
M
–––
10
–––
10
D
K
0.76
1.01
0.030
0.040
G
H
M
M
M
0.13 (0.005)
T
A
B
D SUFFIX
PLASTIC PACKAGE
CASE 751–05
(SO–8)
NOTES:
D
A
ISSUE R
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. DIMENSIONS ARE IN MILLIMETERS.
3. DIMENSION D AND E DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS
OF THE B DIMENSION AT MAXIMUM MATERIAL
CONDITION.
8
1
5
4
C
M
M
0.25
B
H
E
MILLIMETERS
B
e
DIM
A
A1
B
C
D
MIN
1.35
0.10
0.35
0.18
4.80
3.80
MAX
1.75
0.25
0.49
0.25
5.00
4.00
h X 45
A
C
SEATING
PLANE
E
e
H
h
L
1.27 BSC
0.10
5.80
0.25
0.40
0
6.20
0.50
1.25
7
A1
B
L
M
S
S
0.25
C
B
A
18
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
Opportunity/Affirmative Action Employer.
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
19
MOTOROLA ANALOG IC DEVICE DATA
MC33341
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315
Mfax : RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MC33341/D
◊
相关型号：
©2020 ICPDF网 联系我们和版权申明