DS1666S-50+T&R [MAXIM]
Analog Circuit, PDSO16, 0.300 INCH, SOIC-16;
| 型号： | DS1666S-50+T&R |
| 厂家： | 
MAXIM INTEGRATED PRODUCTS |
| 描述： | Analog Circuit, PDSO16, 0.300 INCH, SOIC-16 光电二极管 |
| 文件： | 总9页 (文件大小：138K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DS1666
Audio Digital Resistor
www.dalsemi.com
FEATURES
PIN ASSIGNMENT
ꢀ 128 position, digitally controlled poten-
NC
1
14 NC
tiometer
2
13
12
U/D
VCC
VB
ꢀ Operates from a +5 volts power supply with
TTL signal inputs
3
4
5
INC
CS
11 VW
ꢀ Wide analog voltage range of ±5 volts
ꢀ Low-power CMOS
GND
10
VH
6
7
9
8
VL
NC
NC
NC
ꢀ 14-pin DIP or 16-pin SOIC for surface
mount applications
14-PIN DIP (300 MIL)
See Mech. Drawings Section
ꢀ Default position on power up sets wiper
position to 10% of active digital taps (3% of
the total end-to-end resistance)
ꢀ Operating temperature range
– Industrial temp. range: -40°C to +85°C
U/D
1
16
VCC
NC
VB
NC
NC
2
3
15
14
INC
4
13
VW
NC
CS
NC
5
6
7
12
11
10
VH
NC
NC
Resistance/Step
Resistance values Low End High End -3dB Point
GND
8
9
VL
DS1666-10 10K
DS1666-50 50K
24Ω
152Ω
759Ω
1.0 MHz
200 kHz
16-PIN SOIC (300 MIL)
122Ω
See Mech. Drawings Section
DS1666-100 100K 243Ω
1.519Ω 100 kHz
PIN DESCRIPTIONS
VH
VL
VW
U/ D
INC
- High Terminal of Potentiometer
- Low Terminal of Potentiometer
- Wiper Terminal of Potentiometer
- Up/Down Control
- Wiper Movement Control
CS
- Chip Select for Wiper Movement
NC
VCC
GND
VB
- No Connection
- 5V Power Supply Input
- Ground
- Substrate Bias Voltage (0 to -5V)
DESCRIPTION
The DS1666 Audio Digital Resistor is a solid-state potentiometer composed of 127 digitally controlled
resistive elements. Between each resistive section and both ends of the potentiometer are tap points
multiplexed to the wiper. The position of the wiper on the resistance array is controlled by the CS , U/ D
and INC inputs. The taper of the DS1666 is shown in Figure 1.
1 of 9
102899
DS1666
The DS1666 is uniquely designed to provide a potentiometer that is pseudo-logarithmic rather than linear
across its entire range. The lower half of the potentiometer advances 1% of total resistance for each 3%
of scale advanced, providing for precise amplification of low volume signals. The upper half of the
potentiometer advances 2% of resistance for every 1% of scale advanced, providing for the lower
resolution gain required for high volume amplification.
GRAPH OF AUDIO TAPER Figure 1
OPERATION
The DS1666 has a total of 128 tap-points including the VL and VH terminals. A total of 127 resistive
segments exist between the VL and VH terminals. These tap-points are accessible to the VW terminal
whose position is controlled via a 3-terminal control port. A block diagram of the DS1666 is shown in
Figure 2.
The 3-terminal port of the DS1666 provides an increment/ decrement interface which is activated via a
chip select input. This interface consists of the input signals CS , INC , and U/ D . These input signals
control a 7-bit up/down counter. The output of the 7-bit up/down counter controls a 1 of 128 decoder to
select wiper position. The timing diagram for the 3-terminal interface control is shown in Figure 4.
ANALOG CHARACTERISTICS
The DS1666 has a pseudo-logarithmic resistor array that resembles an audio taper potentiometer as
shown in Figure 1. Taps on the lower portion of the potentiometer increment 0.25% of the total
resistance and are specified to within ±0.5% of the expected value. Taps on the higher portion increment
1.5% of the total resistance and are specified to within ±2.0% of the expected value.
End-to-End Resistance Tolerance = ±20 %
Temperature Coefficient = 750 PPM/°C typical
2 of 9
102899
DS1666
PIN DESCRIPTIONS
VCC - Power Supply. The DS1666 will support supply voltages ranging from +4.5 to +5.5 volts.
GND - Ground Terminal.
VB - Negative Bias. The DS1666 will support a negative bias ranging from 0 to -5 volts.
H - High-Terminal of Potentiometer. It is not required that this terminal be connected to a potential
greater than the VL terminal. Voltage applied to the VH terminal can not exceed the power-supply
voltage, (VCC), or go below the negative bias, (VB).
VL - Low-Terminal of Potentiometer. It is not required that this terminal be connected to a potential less
than the VH terminal. Voltage applied to the VL terminal cannot exceed the power-supply voltage, (VCC),
or go below the negative bias (VB).
VW - Wiper of the Potentiometer. Its position on the resistor array is controlled by the 3-terminal control
port. Voltage applied to the wiper cannot exceed the power-supply voltage, VCC, or go below the
negative bias (VB).
CS - Chip Select. The CS input is used to activate the control port of the DS1666. This input is active
low. When in a high-state, activity on the INC and U/ D port pins will not affect or change wiper
position.
INC - Wiper Movement Control. This input provides for wiper position changes when the CS pin is low.
Wiper position changes will occur one position per high-to-low transition of this input signal. Position
changes will not occur if the CS pin is in a high-state.
U/D - Up/Down Control. This input sets the direction of wiper movement. When in a high-state and CS
is low, any high-to-low transition on INC will cause a one position movement of the wiper towards the
VH terminal. When in a low-state and CS is low, any high-to-low transitions on INC will cause the
position of the wiper to move towards the VL terminal.
3 of 9
102899
DS1666
BLOCK DIAGRAM Figure 2
MODE SELECTION Figure 3
4 of 9
102899
DS1666
ABSOLUTE MAXIMUM RATINGS*
Voltage on CS , INC , U/ D and U/ D and VCC Relative to Ground -0.5V to +7.0V
Voltage on VH, VL and VW Relative to Ground
Voltage on VB
-6.5V to +6.5V
-6.5V to GND
Operating Temperature
-40° to +85°C
Storage Temperature
-55°C to +125°C
260°C for 10 seconds
Soldering Temperature
* This is a stress rating only and functional operation of the device at these or any other conditions above
those indicated in the operation sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of time may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS
(-40°C to +85°C)
PARAMETER
Supply Voltage
Input Logic 1
SYMBOL
MIN
+4.5
2.0
TYP
MAX
5.5
UNITS NOTES
VCC
5.0
V
V
V
V
V
1
1
VIH
VCC+0.5
+0.8
Input Logic 0
VIL
-0.5
1
VH, VL, VW Voltage
VB Voltage
VR
VB-0.3
-5.5
VCC+0.3
GND
1, 3
1
VB
DC ELECTRICAL CHARACTERISTICS
(-40°C to +85°C; VCC = 5.0V ± 10%)
PARAMETER
SYMBOL
MIN
TYP
MAX
4.5
+1
UNITS NOTES
Supply Current
ICC
ILI
0.2
mA
µA
Ω
4
2
Input Leakage
Wiper Resistance
Wiper Current
-1
RW
IW
350
900
1
mA
CAPACITANCE
(tA=25°C)
PARAMETER
SYMBOL CONDITION
TYP
MAX
UNITS NOTES
Capacitance
CIN
6
pF
tA=25°C
5 of 9
102899
DS1666
ANALOG RESISTOR CHARACTERISTICS (-40°C to +85°C; VCC = 5.0V ± 10%)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS NOTES
Total Resistance
“-10”
“-50”
“-100”
10
50
5
5
5
KΩ
KΩ
KΩ
%
100
End-to-End Resistor Tolerance
Absolute Tolerance
-20
+20
8
Low End (0.25% Increments)
High End (1.5% Increments)
-3 dB Cutoff Frequency
Temperature Coefficient
-0.5
-2.0
+0.5
+2.0
%
%
6
6
7
fCUTOFF
MHz
ppm/°C
750
AC ELECTRICAL CHARACTERISTICS
(-40°C to +85°C; VCC = 5.0V ± 10%)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS NOTES
tCI
100
ns
CS to INC Setup
tID
tDI
tIL
100
1
ns
µs
ns
µs
ns
INC High to U/ D Change
U/ D to INC Setup
500
1
INC Low Period
tIH
tIW
INC High Period
200
INC Low to Wiper Change
6 of 9
102899
DS1666
AC TIMING Figure 4
NOTES:
1. All Voltages are referenced to ground.
2. Typical Values are for TA=25°C and nominal supply voltages.
3. Resistors input voltages cannot go below VB or exceed VCC by the amounts shown.
4. Maximum current specifications are based on the clock rate of INC input. This specification
represents the current required when changing the wiper position.
5. The DS1666 is available in three end-to-end resistor values. These include 10KΩ for the DS1666-10;
50KΩ for the DS1666-50; and 100KΩ for the DS1666-100.
6. Absolute tolerance is used to compare measured wiper voltage versus expected wiper voltage as
determined by wiper position.
7. -3dB cutoff frequency characteristics for the DS1666 depend on potentiometer total resistance. The
DS1666-10 is 1 MHz; the DS1666-50 is 200 KHz; and the DS1666-100 is 100 KHz.
8. Valid at 25°C only
AC TEST CONDITIONS
Input Pulse Levels
0V to 3V
Input Rise and Fall Times 10 ns
7 of 9
102899
DS1666
DS1666 ORDERING INFORMATION
ORDERING
NUMBER
PACKAGE
OPERATING
TEMPERATURE
-40°C TO +85°C
-40°C TO +85°C
-40°C TO +85°C
-40°C TO +85°C
-40°C TO +85°C
-40°C TO +85°C
VERSION
DS1666-010
DS1666-050
DS1666-100
DS1666S-010*
DS1666S-050*
DS1666S-100*
14L DIP
14L DIP
14L DIP
16L SOIC (300-mil)
16L SOIC (300-mil)
16L SOIC (300-mil)
10 kΩ
50 kΩ
100 kΩ
10 kΩ
50 kΩ
100 kΩ
* Add “/T & R” for tape and reel packaging.
8 of 9
102899
DS1666
DATA SHEET REVISION SUMMARY
The following represent the key differences between 07/26/93 and 06/18/97 version of the DS1666 data
sheet. Please review this summary carefully.
1. Remove commercial temp grade reference.
2. Add order info table.
3. Improve operating description and add “ANALOG Resistor CHARACTERISTICS”.
9 of 9
102899
相关型号：
©2020 ICPDF网 联系我们和版权申明