58524-2 [MACOM]
PRO-CRIMPER III Hand Crimping Tool Assembly 58524- 1 with Die Assembly 58524- 2; PRO- CRIMPER III手动压线钳大会58524- 1与模具组件58524- 2
| 型号： | 58524-2 |
| 厂家： | 
Tyco Electronics |
| 描述： | PRO-CRIMPER III Hand Crimping Tool Assembly 58524- 1 with Die Assembly 58524- 2 |
| 文件： | 总5页 (文件大小：241K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Instruction Sheet
PRO- CRIMPER* III Hand
Crimping Tool Assembly 58524-1
with Die Assembly 58524-2
408-9993
22 SEP 09 Rev B
PROPER USE GUIDELINES
Cumulative Trauma Disorders can resultfrom the prolonged use ofmanually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended-use, production operations is available.
Stationary Jaw
Back of Tool
Wire Side)
Front of Tool
(Locator Side)
Pivot Pin
PRO-CRIMPER III Hand
Die
Assembly
Crimping Tool Frame
354940-1 (408-9930)
Moving Jaw
Ratchet
Adjustment
Wheel
Stationary
Handle
The PRO-CRIMPER III Hand Crimping Tool is a “Commercial” grade tool
and is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 series specification, but may not comply with other feature
parameters of the specification. Tyco Electronics offers a variety of tools to
satisfy your performance requirements. For additional information, contact the
Tooling Assistance Center at 1-800-722-1111.
Moving Handle
Wire
TE Die
Assembly
Terminal
Family}
Size
(AWG)
Insul Dia
(mm [In.])
Strip Length
(mm [In.])
.250 Series
FASTON*
Receptacle
18--16
14
3.05 to 4.32
[.120 to .170]
4.75 to 5.59
[.180 to .220]
58524-- 2
}
CALL THE TOOLING ASSISTANCE CENTER OR PRODUCT INFORMATION (SEE BELOW) FOR PRODUCT PART NUMBERS.
Figure 1
any terminals.
1. INTRODUCTION
Reasons for reissue are provided in Section 10,
REVISION SUMMARY.
PRO--CRIMPER III Hand Crimping Tool
Assembly 58524--1 consists of Die Assembly
58524--2 and PRO--CRIMPER III Hand Crimping Tool
Frame 354940--1. The die assembly consists of wire
and insulation crimping dies.
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
NOTE
i
Read these instructions thoroughly before crimping
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
E2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
1 of 5
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
TE logo and Tyco Electronics are trademarks.
LOC B
*Trademark. Other products, logos, and company names used are the property of their respective owners.
408-9993
PRO-CRIMPER III Hand Crimping Tool Assembly 58524-1
Tool Frame
Insulation
Crimper
Chamfer
Die Retaining
Pins
Wire Crimper
Wire Anvil
Insulation
Chamfer
Die Retaining
Screws
Anvil
Figure 2
6. Insert the two die retaining pins.
2. DESCRIPTION (Figures 1 and Figure 2)
7. Insert a die retaining screw through the jaw and
through both crimper dies, and tighten the screw
just enough to hold the dies in place. Do not
tighten the screw completely at this time.
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full contact crimping.
The tool frame holds a die assembly with two
crimping sections.
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold
the anvils and crimpers in place, then tighten both
die retaining screws.
The die assembly features a wire anvil, an insulation
anvil, a wire crimper, and an insulation crimper.
Die retaining pins and die retaining screws are used
to position and secure the dies in the tool frame.
9. To disassemble, close the tool handles until the
ratchet releases, remove the two die retaining
screws and the four die retaining pins, and slide
the anvils and crimpers out of the tool jaws.
3. INSTALLATION AND REMOVAL OF
DIE SET (Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
4. CRIMPING PROCEDURE
This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be
verified as specified in Figure 4. Refer to
Section 5, CRIMP HEIGHT INSPECTION, and
Section 6, RATCHET (Crimp Height)
ADJUSTMENT, to verify crimp height before
using the tool to crimp desired terminals and wire
sizes.
NOTE
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
i
3. Insert the two die retaining pins.
4. Insert a die retaining screw through the jaw and
through both anvil dies, and tighten the screw just
enough to hold the dies in place. Do not tighten the
screw completely at this time.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire
to the length indicated in Figure 1, taking care not to
5. Place the wire crimper and insulation crimper so nick or cut wire strands. Select an applicable terminal
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
and identify the appropriate crimp section according
to the wire size markings on the tool. Refer to
Figure 3 and proceed as follows:
2 of 5
Tyco Electronics Corporation
Rev B
408-9993
PRO-CRIMPER III Hand Crimping Tool Assembly 58524-1
Back of Tool
(Wire Side)
Front of Wire Barrel
Even with the Edge
of the Wire Crimper
Wire Crimper
Strip Length
Wire Barrel
Terminal (Typ)
Wire
Figure 3
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
8. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped terminal.
2. Holding the terminal by the mating end, insert
the terminal — insulation barrel first — through the
front of the tool and into the appropriate crimp
section.
The crimped terminal may stick in the crimping
area, but the terminal can be easily removed by
pushing downward on the mating end of the
terminal.
NOTE
i
9. Check the terminal’s crimp height as described
in Section 5, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 6, RATCHET (Crimp Height)
ADJUSTMENT.
3. Position the terminal so that the mating end of
the terminal is on the front side of the tool, and so
that the open “U” of the wire and insulation barrels
face the top of the tool. Place the terminal up into
the nest.
4. Rotate the tool sufficiently to be able to view the
front side of the wire crimper, and position the
terminal so that the front edge of the wire barrel is
even with the front edge of the wire crimper, as
shown in Figure 3.
5. CRIMP HEIGHT INSPECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp--height comparator. Tyco
Electronics does not manufacture or market
crimp--height comparators. Detailed information on
obtaining and using crimp--height comparators can be
found in instruction sheet 408--7424.
Make sure that both sides of the insulation barrel
are started evenly into the crimping section. Do
NOT attempt to crimp an improperly positioned
terminal.
CAUTION
!
Proceed as follows:
5. Hold the terminal in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the terminal in position. Do NOT
deform insulation barrel or wire barrel.
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
6. Rotate the tool so that the back (wire side) is
once again facing you.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET ADJUSTMENT.
7. Insert stripped wire into terminal insulation and
wire barrels until the end of the wire is even with
the edge of the wire barrel and wire crimper, as
shown in Figure 3.
Rev B
Tyco Electronics Corporation
3 of 5
408-9993
PRO-CRIMPER III Hand Crimping Tool Assembly 58524-1
Position Point
on Center of
Wire Barrel
Opposite
7. MAINTENANCE
Ensure that the tool and dies are clean by wiping
them with a clean, soft cloth. Remove any debris with
a clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
closed to prevent objects from becoming lodged in
the crimping dies, and store in a clean, dry area.
Seam
Modified Anvil
“A”
Crimp Height
Dimension A and
Tolerance (+)
Wire Size
AWG (Max)
Crimp Section
(Wire Size Marking)
8. VISUAL INSPECTION
The crimping dies should be inspected on a regular
basis to ensure that they have not become worn or
damaged. Inspect the crimp sections for flattened,
chipped, worn, or broken areas. If damage or
abnormal wear is evident, the tool must be replaced.
See Section 9, REPLACEMENT.
1.55 + .05
16
10
18--16
[.061 + .002]
1.83 + .05
[.072 + .002]
10
Figure 4
9. REPLACEMENT
6. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)
Customer--replaceable parts are shown in Figure 1.
1. Remove the lockscrew from the ratchet
adjustment wheel.
Available separately, Repair Kit 679221--1 includes a
replacement nut and a variety of pins, rings, screws,
and springs.
2. With a screwdriver, adjust the ratchet wheel
from the front side of the tool.
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher--numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower--numbered setting.
If the dies are damaged or worn excessively, they
must be replaced.
Order the repair kit and replaceable parts through
your Tyco Electronics representative, or call
1--800--526--5142, or send a facsimile of your
purchase order to 1--717--986--7605, or write to:
4. Replace the lockscrew.
CUSTOMER SERVICE (38--35)
TYCO ELECTRONICS
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
PO BOX 3608
HARRISBURG PA 17105--3608
10. REVISION SUMMARY
Screwdriver
Revisions to this instruction sheet include:
S Changed PRO--CRIMPER II Hand Tool to
PRO--Crimper III Hand Tool;
S Revised Crimp--Height Inspection section;
S Updated format to current corporate
requirements;
S Applied TE logo; and
S Added back page illustrating tooling available
for dies 58525--2.
Ratchet
Adjustment
Wheel
Lockscrew
(Typ)
Figure 5
4 of 5
Tyco Electronics Corporation
Rev B
408-9993
PRO-CRIMPER III Hand Crimping Tool Assembly 58524-1
Die Assembly 58524-2 Can Be Used In the Following Tools:
PRO-CRIMPER III Hand Tool 354940-1
(Instruction Sheet 408-9930)
SDE PEW-12 Hand Tool 9-1478240-0
(Instruction Sheet 408-8851)
SDE Bench Terminator 1490076-2
(Customer Manual 409-10052)
626 Adapter 679304-1
(Instruction Sheet 408-4070)
Battery Tool (Pin Die) 1213890-1, -2
(Customer Manual 409-10065)
Battery Tool (Shouldered Die) 1725837-1, -2
(Customer Manual 409-10053)
Rev B
Tyco Electronics Corporation
5 of 5
相关型号：
5852BK001
Wire And Cable, 7 Conductor(s), 28AWG, 600V, Flexible Cord And Fixture Wire, ROHS AND REACH COMPLIANT
ALPHAWIRE
58537-302LF
Board Connector, 24 Contact(s), 4 Row(s), Male, Straight, Press Fit Terminal, LEAD FREE
AMPHENOL
©2020 ICPDF网 联系我们和版权申明