1804174-1 [MACOM]
Reasons for reissue of this instruction sheet are provided in Section 7, REVISION SUMMARY;型号: | 1804174-1 |
厂家: | Tyco Electronics |
描述: | Reasons for reissue of this instruction sheet are provided in Section 7, REVISION SUMMARY |
文件: | 总2页 (文件大小:113K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Instruction Sheet
Removal Tools 1804171-1, 1804173-1, and
1804174-1 for Housing of Z-PACK*
Hard Metric (HM)-Zd Right-Angle Headers
408-10055
10 SEP 09 Rev B
Release
Block
If adjusting both pushers, pull the other lever arm,
with the lever attached, from the groove pin.
2. Flip the pusher(s) so that either the
Thumbscrew
Knob
longer--length end (standard position, shown in
Figure 2) or shorter--length end (reversed position)
faces the front of the removal tool. For the
standard position, make sure that the indent of the
pusher faces outward. Refer to Figure 2.
Puller
Pusher
(2 Places)
3. Place the hole of the lever arm onto the groove
pin, and place the dowel pin of the lever arm into
the hole (of the pusher) closest to back of removal
tool. Refer to Figure 2.
Lever Arm
(2 Places)
Lever
If adjusting both pushers, do the same for the other
lever arm (with the lever attached).
REMOVAL TOOL
1804171--1
RIGHT-ANGLE HEADER
2--Pair
3--Pair
4--Pair
4. Secure the lever arm to the lever with the
screws.
1804173--1
1804174--1
Figure 1
Groove
Pin
1. INTRODUCTION
Longer-Length
End of Pusher
The removal tools listed in Figure 1 are designed to
remove the housing from the chicklets of Z--PACK
HM--Zd right--angle headers. The chicklets will remain
on the printed circuit (pc) board.
Dowel
Pin
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
Lever
Arm
Front of
Removal Tool
2. DESCRIPTION
Indent
Screws
Each removal tool consists of the components shown
in Figure 1. After the release block is attached to the
front of the header, the thumbscrew knob is used to
secure the puller to the housing. Rotating the lever
moves the pushers against the pc board and pulls the
housing from the header.
Shorter-Length
End of Pusher
Hole
HEADER
LOCATION
LEFT PUSHER
POSITION
RIGHT PUSHER
POSITION
3. ADJUSTMENT
Single
Standard
Reversed
Standard
Reversed
Standard
Standard
Reversed
Reversed
Before using the removal tool, each pusher must be
positioned according to the location of the header on
the pc board. Refer to Figure 2.
Right End of Stack
Left End of Stack
Middle of Stack
To avoid damage to the header or pc board,
make sure that the pushers are properly
positioned before using the removal tool.
CAUTION
Figure 2
!
Adjust the pusher(s) as follows:
4. REMOVAL PROCEDURE
1. Remove the screws that secure the lever arm
(to be adjusted) onto the lever. Pull the lever arm
from the groove pin. See Figure 2.
1. Loosen, but do not remove, the thumbscrew so
that the puller can be positioned at an angle. See
Figure 3, Detail A.
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
E2009 Tyco Electronics Corporation, Harrisburg, PA
1 of 2
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
LOC B
*Trademark. Other products, logos, and company names used are the property of their respective owners.
408-10055
Removal Tools 1804171-1, 1804173-1, and 1804174-1
2. Slide the removal tool onto the front of the
header so that the blades fit over the header
ground shields. See Figure 3, Detail A.
6. Pull the removal tool (with the housing) straight
away from the header. DO NOT tilt the removal
tool.
7. Loosen the thumbscrew knob, and lower the
puller away from the housing.
3. Push the removal tool straight into the header
until the blades butt against the housing.
Straighten the puller so that the teeth of the puller
fit over the back edge of the housing. See
Figure 3, Detail B.
8. Pull the housing from the removal tool.
5. MAINTENANCE
4. Hold the puller in place, and tighten the
thumbscrew knob.
It is recommended that each operator be made aware
of, and responsible for, the following steps of daily
maintenance:
5. Slowly pull the lever away from the pc board
until the pushers butt against the pc board. Make
sure that the removal tool moves straight. DO NOT
allow the removal tool to tilt. See Figure 3,
Detail C.
1. Remove dust, moisture, and other contaminants
from the removal tool with a clean, soft brush, or
lint--free cloth. DO NOT use objects that could
damage the removal tool.
2. When the removal tool is not in use, store it in a
clean, dry area.
Detail A
Ground
Shields
Blades
Header
6. REPLACEMENT AND REPAIR
Order removal tools through your representative, or
call 1--800--526--5142, or send a facsimile of your
purchase order to 717--986--7605, or write to:
CUSTOMER SERVICE (038--035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
PC Board
Housing
Puller
HARRISBURG PA 17105--3608
For customer repair service, call 1--800--526--5136.
Detail B
7. REVISION SUMMARY
Revisions to this instruction sheet include:
S Updated instruction sheet to corporate
requirements
Teeth of Puller
Over Back Edge
of Housing
Detail C
Pull Lever
Pusher (2 Places)
Against PC Board
Figure 3
2 of 2
Tyco Electronics Corporation
Rev B
相关型号:
©2020 ICPDF网 联系我们和版权申明