1804177-1 [MACOM]
Press down evenly on the extraction tool until it bottoms on the chicklet;
| 型号： | 1804177-1 |
| 厂家： | 
Tyco Electronics |
| 描述： | Press down evenly on the extraction tool until it bottoms on the chicklet |
| 文件： | 总2页 (文件大小：86K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Instruction Sheet
Extraction Tools 1804175-1, 1804176-1, and
1804177-1 for Chicklets of Z-PACK*
Hard Metric (HM)-Zd Right-Angle Headers
408-10057
10 SEP 09 Rev B
3. Press down evenly on the extraction tool until it
bottoms on the chicklet. Make sure that the row of
contacts enters the slot of the insertion leg.
4. Hold onto the pc board, and gently rock the
extraction tool toward the front of the chicklet,
creating interference (the chicklet will pivot out
slightly).
DO NOT try to pull the chicklet straight off of the
Insertion
Leg
NOTE
pc board; otherwise, the extraction tool will slip
off of the chicklet.
Support
Leg
i
5. Continue to rock the extraction tool back--and--
forth until the chicklet lifts away from the pc board.
6. Discard the chicklet.
EXTRACTION TOOL
1804175--1
RIGHT-ANGLE HEADER
2--Pair
3--Pair
4--Pair
Detail A
1804176--1
Press Down
Slot of
Insertion Leg
1804177--1
Figure 1
Row of
Contacts
1. INTRODUCTION
The extraction tools listed in Figure 1 are designed to
remove individual chicklets of Z--PACK HM--Zd
right--angle headers from the printed circuit (pc)
board.
Back of
Chicklet
Reasons for reissue of this instruction sheet are
provided in Section 6, REVISION SUMMARY.
PC Board
2. DESCRIPTION
Detail B
Each extraction tool features an insertion leg with a
slot designed to straddle the row of contacts, and a
support leg that supports the back of the chicklet
during extraction.
Rock Extraction Tool Back -and -Forth
3. EXTRACTION PROCEDURE
Insertion Tool
Bottomed on
Chicklet
1. Refer to instruction sheet 408--10055, and
remove the housing from the pc board.
The housing of the right -angle header must be
removed from the pc board before the chicklets
can be removed.
NOTE
i
2. Position the extraction tool over the chicklet to
be removed so that the support leg is aligned with
the back of the chicklet and the row of contacts will
enter the slot of the insertion leg. See Figure 2,
Detail A.
Figure 2
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
E2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
1 of 2
TE logo and Tyco Electronics are trademarks.
LOC B
*Trademark. Other products, logos, and company names used are the property of their respective owners.
408-10057
Extraction Tools 1804175-1, 1804176-1, and 1804177-1
4. MAINTENANCE
5. ORDERING INFORMATION
Order extraction tools through your representative, or
call 1--800--526--5142, or send a facsimile of your
purchase order to 717--986--7605, or write to:
It is recommended that each operator be made aware
of, and responsible for, the following steps of daily
maintenance:
CUSTOMER SERVICE (038--035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or lint--free cloth. DO NOT
use objects that could damage the extraction tool.
HARRISBURG PA 17105--3608
2. When the extraction tool is not in use, store it in
a clean, dry area.
6. REVISION SUMMARY
Revisions to this instruction sheet include:
S Updated instruction sheet to corporate
requirements
2 of 2
Tyco Electronics Corporation
Rev B
相关型号：
©2020 ICPDF网 联系我们和版权申明