LTC4088EDE#TRPBF [Linear]
LTC4088 - High Efficiency Battery Charger/USB Power Manager; Package: DFN; Pins: 14; Temperature Range: -40°C to 85°C;型号: | LTC4088EDE#TRPBF |
厂家: | Linear |
描述: | LTC4088 - High Efficiency Battery Charger/USB Power Manager; Package: DFN; Pins: 14; Temperature Range: -40°C to 85°C 电池 光电二极管 |
文件: | 总24页 (文件大小:298K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LTC4088
High Efficiency Battery
Charger/USB Power Manager
FeaTures
DescripTion
The LTC®4088 is a high efficiency USB PowerPath™
controller and Li-Ion/Polymer battery charger. It includes
a synchronous switching input regulator, a full-featured
battery charger and an ideal diode. Designed specifically
for USB applications, the LTC4088’s switching regulator
automatically limits its input current to either 100mA,
500mA or 1A for wall-powered applications via logic
control.
n
Switching Regulator Makes Optimal Use of Limited
Power Available from USB Port to Charge Battery
and Power Application
180mΩ Internal Ideal Diode Plus Optional External
n
Ideal Diode Controller Seamlessly Provides Low
Loss Power Path When Input Power is Limited or
Unavailable
n
Full Featured Li-Ion/Polymer Battery Charger
n
V
Operating Range: 4.25V to 5.5V (7V Absolute
BUS
The switching input stage provides power to V
where
OUT
Maximum—Transient)
power sharing between the application circuit and the
battery charger is managed. Unlike linear PowerPath
controllers, the LTC4088’s switching input stage can use
nearly all of the 0.5W or 2.5W available from the USB port
with minimal power dissipation. This feature allows the
LTC4088 to provide more power to the application and
eases thermal issues in space-constrained applications.
n
n
n
n
n
1.2A Maximum Input Current Limit
1.5A Maximum Charge Current with Thermal Limiting
Bat-Track™ Adaptive Output Control
Slew Control Reduces Switching EMI
Low Profile (0.75mm) 14-Lead 4mm × 3mm DFN
Package
An ideal diode ensures that system power is available
from the battery when the input current limit is reached
or if the USB or wall supply is removed.
applicaTions
n
Media Players
n
Digital Cameras
The LTC4088 is available in the low profile 14-lead 4mm
× 3mm × 0.75mm DFN surface mount package.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and
PowerPath, Bat-Track and ThinSOT are trademarks of Linear Technology Corporation. All other
trademarks are the property of their respective owners. Protected by U.S. Patents, including
6522118.
n
GPS
n
PDAs
n
Smart Phones
Typical applicaTion
Switching Regulator Efficiency to
System Load (POUT/PBUS
)
High Efficiency Battery Charger/USB Power Manager
100
90
80
70
60
50
40
30
20
10
WALL
USB
3.3µH
SYSTEM
LOAD
V
D0
D1
D2
CHRG
LDO3V3
SW
V
BAT = 4.2V
BUS
OUT
10µF
GATE
BAT
BAT = 3.3V
LTC4088
10µF
3.3V
CLPROG
PROG C/X GND NTC
V
I
= 5V
BUS
1µF
+
= 0mA
BAT
8.2Ω
Li-Ion
10x MODE
2.94k
499Ω
0.1µF
0
4088 TA01a
0.01
0.1
(A)
1
I
OUT
4088 TA01b
4088fb
1
LTC4088
absoluTe MaxiMuM raTings
pin conFiguraTion
(Note 1)
TOP VIEW
V
V
(Transient) t < 1ms, Duty Cycle < 1%.. –0.3V to 7V
BUS
BUS
NTC
CLPROG
LDO3V3
D2
1
2
3
4
5
6
7
14 D1
13 D0
12 SW
(Static), BAT, CHRG, NTC, D0,
D1, D2.......................................................... –0.3V to 6V
I
I
....................................................................3mA
CLPROG
PROG C/X
I
15
11
10
9
V
V
BUS
OUT
, I ................................................................2mA
C/X
PROG
CHRG
BAT
...................................................................30mA
LDO3V3
8
GATE
I
I
I
......................................................................75mA
CHRG
OUT
SW
............................................................................2A
DE PACKAGE
14-LEAD (4mm × 3mm) PLASTIC DFN
..............................................................................2A
T
JMAX
= 125°C, θ = 37°C/W
JA
EXPOSED PAD (PIN 15) IS GND, MUST BE SOLDERED TO PCB
IBAT ............................................................................2A
Maximum Operating Junction Temperature .......... 125°C
Operating Temperature Range .................–40°C to 85°C
Storage Temperature Range .................. –65°C to 125°C
orDer inForMaTion
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
14-Lead (4mm × 3mm) Plastic DFN
TEMPERATURE RANGE
–40°C to 85°C
LTC4088EDE#PBF
LTC4088EDE#TRPBF
4088
Consult LTC Marketing for parts specified with wider operating temperature ranges.
Consult LTC Marketing for information on nonstandard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
elecTrical characTerisTics The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VBUS = 5V, BAT = 3.8V, RCLPROG = 2.94k, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Input Power Supply
l
V
Input Supply Voltage
Total Input Current
4.35
5.5
V
BUS
l
l
l
l
l
I
1x Mode
92
445
815
0.32
1.6
97
100
500
1000
0.50
2.5
mA
mA
mA
mA
mA
BUS(LIM)
5x Mode
470
877
0.39
2.05
10x Mode
Low Power Suspend Mode
High Power Suspend Mode
I
(Note 4)
Input Quiescent Current
1x Mode
6
mA
mA
mA
mA
mA
BUSQ
5x Mode
14
10x Mode
Low Power Suspend Mode
High Power Suspend Mode
14
0.038
0.038
h
(Note 4) Ratio of Measured V
Current to
BUS
1x Mode
224
1133
2140
11.3
59.4
mA/mA
mA/mA
mA/mA
mA/mA
mA/mA
CLPROG
CLPROG Program Current
5x Mode
10x Mode
Low Power Suspend Mode
High Power Suspend Mode
4088fb
2
LTC4088
elecTrical characTerisTics The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VBUS = 5V, BAT = 3.8V, RCLPROG = 2.94k, unless otherwise noted.
SYMBOL
PARAMETER
Current Available Before
CONDITIONS
MIN
TYP
MAX
UNITS
I
V
1x Mode, BAT = 3.3V
5x Mode, BAT = 3.3V
10x Mode, BAT = 3.3V
Low Power Suspend Mode
High Power Suspend Mode
135
672
1251
0.32
2.04
mA
mA
mA
mA
mA
OUT
OUT
Discharging Battery
0.26
1.6
0.41
2.46
V
V
V
V
CLPROG Servo Voltage in Current Limit 1x, 5x, 10x Modes
Suspend Modes
1.188
100
V
CLPROG
mV
V
Undervoltage Lockout
Rising Threshold
Falling Threshold
4.30
4.00
4.35
V
V
UVLO
BUS
3.95
3.5
V
to BAT Differential Undervoltage
Rising Threshold
Falling Threshold
200
50
mV
mV
DUVLO
OUT
BUS
Lockout
V
Voltage
1x, 5x, 10x Modes, 0V < BAT ≤ 4.2V,
OUT
BAT + 0.3
4.7
V
OUT
I
= 0mA, Battery Charger Off
USB Suspend Modes, I
= 250µA
4.5
1.8
4.6
4.7
2.7
V
MHz
Ω
OUT
f
Switching Frequency
2.25
0.18
0.30
OSC
R
R
PMOS On Resistance
NMOS On Resistance
Peak Inductor Current Clamp
PMOS
NMOS
PEAK
Ω
I
1x, 5x Modes
10x Mode
2
3
A
A
R
SUSP
Suspend LDO Output Resistance
15
Ω
Battery Charger
V
BAT Regulated Output Voltage
Constant-Current Mode Charge Current
Battery Drain Current
4.179
4.165
4.200
4.200
4.221
4.235
V
V
FLOAT
0°C ≤ T ≤ 85°C
A
I
I
R
PROG
R
PROG
= 1k
= 5k
980
192
1030
206
1080
220
mA
mA
CHG
V
> V , PowerPath Switching
UVLO
3.5
5
µA
BAT
BUS
Regulator On, Battery Charger Off,
I
= 0µA
OUT
V
= 0V, I
= 0µA (Ideal Diode Mode)
OUT
23
35
µA
V
BUS
V
V
PROG Pin Servo Voltage
1.000
0.100
PROG
PROG Pin Servo Voltage in Trickle
Charge
BAT < V
V
PROG,TRKL
TRKL
h
Ratio of I to PROG Pin Current
1031
2.85
135
–100
4.0
mA/mA
V
PROG
BAT
V
Trickle Charge Threshold Voltage
Trickle Charge Hysteresis Voltage
Recharge Battery Threshold Voltage
Safety Timer Termination Period
Bad Battery Termination Time
BAT Rising
2.7
3.0
TRKL
ΔV
mV
TRKL
RECHRG
TERM
V
Threshold Voltage Relative to V
–80
3.2
0.4
85
–120
4.8
mV
FLOAT
t
t
I
Timer Starts when V = V
Hour
Hour
BAT
FLOAT
BAT < V
0.5
0.6
BADBAT
C/X
TRKL
Battery Charge Current at Programmed
End of Charge Indication
R
C/X
R
C/X
= 1k
= 5k
100
20
115
mA
mA
V
C/X Threshold Voltage
100
1031
65
mV
mA/mA
mV
C/X
h
C/X
Battery Charge Current Ratio to C/X
CHRG Pin Output Low Voltage
CHRG Pin Input Current
V
I
= 5mA
100
1
CHRG
CHRG
CHRG
I
BAT = 4.5V, V
= 5V
0
µA
CHRG
4088fb
3
LTC4088
elecTrical characTerisTics The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VBUS = 5V, BAT = 3.8V, RCLPROG = 2.94k, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
= 200mA
MIN
TYP
MAX
UNITS
R
Battery Charger Power FET
On-Resistance (Between V
I
0.18
Ω
ON_CHG
BAT
and BAT)
OUT
T
Junction Temperature in Constant
Temperature Mode
110
°C
LIM
NTC
V
COLD
V
HOT
V
DIS
Cold Temperature Fault Threshold
Voltage
Rising Threshold
Hysteresis
75.0
33.4
0.7
76.5
1.5
78.0
36.4
2.7
%V
%V
BUS
BUS
Hot Temperature Fault Threshold
Voltage
Falling Threshold
Hysteresis
34.9
1.5
%V
%V
BUS
BUS
NTC Disable Threshold Voltage
Falling Threshold
Hysteresis
1.7
50
%V
BUS
mV
I
NTC Leakage Current
V
NTC
= V = 5V
BUS
–50
50
nA
NTC
Ideal Diode
V
Forward Voltage Detection
I
= 10mA
= 0V, I
15
2
mV
mV
FWD
OUT
BUS
V
= 10mA
OUT
R
Internal Diode On Resistance, Dropout
Diode Current Limit
I
= 200mA
0.18
Ω
A
DROPOUT
OUT
I
2
MAX
Always On 3.3V Supply
V
Regulated Output Voltage
0mA < I
< 25mA
3.1
3.3
25
3.4
0.4
V
Ω
Ω
LDO3V3
LDO3V3
R
R
Open-Loop Output Resistance
Closed-Loop Output Resistance
OL3V3
3.6
CL3V3
Logic (D0, D1, D2)
V
Input Low Voltage
V
V
IL
IH
V
Input High Voltage
1.2
I
PD
Static Pull-Down Current
V
PIN
= 1V
2
µA
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC4088E is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 85°C operating
temperature range are assured by design, characterization and correlation
with statistical process controls.
Note 3: The LTC4088E includes overtemperature protection that is
intended to protect the device during momentary overload conditions.
Junction temperature will exceed 125°C when overtemperature protection
is active. Continuous operation above the specified maximum operating
junction temperature may impair device reliability.
Note 4: Total input current is the sum of quiescent current, I
, and
BUSQ
measured current given by V
/R
• (h
+ 1)
CLPROG CLPROG
CLPROG
4088fb
4
LTC4088
TA = 25°C, unless otherwise noted.
Typical perForMance characTerisTics
Ideal Diode Resistance
vs Battery Voltage
Output Voltage vs Output Current
(Battery Charger Disabled)
Ideal Diode V-I Characteristics
1.0
0.8
0.6
0.4
0.2
0
0.25
0.20
0.15
0.10
0.05
0
4.50
4.25
4.00
3.75
3.50
3.25
V
= 5V
INTERNAL IDEAL DIODE
WITH SUPPLEMENTAL
EXTERNAL VISHAY
Si2333 PMOS
BUS
V
= 4V
BAT
5x MODE
INTERNAL IDEAL
DIODE
INTERNAL IDEAL
DIODE ONLY
V
= 3.4V
BAT
INTERNAL IDEAL DIODE
WITH SUPPLEMENTAL
EXTERNAL VISHAY
Si2333 PMOS
V
V
= 0V
= 5V
BUS
BUS
0
0.04
0.08
0.12
0.16
0.20
2.7
3.0
3.3
3.6
3.9
4.2
0
200
400
600
800
1000
FORWARD VOLTAGE (V)
BATTERY VOLTAGE (V)
OUTPUT CURRENT (mA)
4088 G01
4088 G02
4088 G03
USB Limited Battery Charge
Current vs Battery Voltage
USB Limited Battery Charge
Current vs Battery Voltage
Battery Drain Current
vs Battery Voltage
700
600
150
125
25
20
15
10
5
I
= 0µA
OUT
V
BUS
= 0V
V
R
R
= 5V
BUS
500
400
300
200
100
0
V
R
R
= 5V
BUS
= 1k
PROG
CLPROG
100
75
= 1k
PROG
CLPROG
= 2.94k
= 2.94k
50
25
0
V
= 5V
BUS
(SUSPEND MODE)
1x USB SETTING,
BATTERY CHARGER SET FOR 1A
5x USB SETTING,
BATTERY CHARGER SET FOR 1A
0
3.0
3.3
3.6
4.2
2.7
3.9
2.7 3.0 3.3 3.6
BATTERY VOLTAGE (V)
3.9
4.2
2.7
3.0
3.3
3.6
3.9
4.2
BATTERY VOLTAGE (V)
BATTERY VOLTAGE (V)
4088 G04
4088 G05
4088 G06
Battery Charging Efficiency vs
PowerPath Switching Regulator
Efficiency vs Output Current
VBUS Current vs VBUS Voltage
(Suspend)
Battery Voltage with No External
Load (PBAT/PBUS
)
100
90
80
70
60
50
40
90
88
86
84
82
80
50
40
30
20
10
0
V
= 3.8V
I
= 0mA
R
R
I
= 2.94k
BAT
OUT
CLPROG
PROG
OUT
5x, 10x MODE
= 1k
1x MODE
= 0mA
5x CHARGING
EFFICIENCY
1x CHARGING
EFFICIENCY
0.01
0.1
OUTPUT CURRENT (A)
1
2.7
3.0
3.3
3.6
3.9
4.2
1
2
3
4
5
6
BATTERY VOLTAGE (V)
V
VOLTAGE (V)
BUS
4088 G07
4088 G08
4088 G09
4088fb
5
LTC4088
TA = 25°C, unless otherwise noted.
Typical perForMance characTerisTics
Output Voltage vs Output Current
in Suspend
VBUS Current vs Output Current in
Suspend
3.3V LDO Output Voltage
vs Load Current, VBUS = 0V
5.0
4.5
4.0
3.5
3.0
2.5
2.5
2.0
1.5
1.0
0.5
0
3.4
3.2
3.0
2.8
2.6
V
BAT
= 3.5V
V
V
= 5V
V
BAT
= 3.9V, 4.2V
BUS
BAT
V
= 3.4V
BAT
5x MODE
= 3.3V
V
BAT
= 3.6V
R
= 2.94k
CLPROG
5x MODE
1x MODE
V
= 3V
BAT
V
= 3.1V
BAT
V
V
R
= 5V
BUS
BAT
1x MODE
1.5
V
= 3.2V
= 3.3V
BAT
= 2.94k
CLPROG
V
= 3.3V
BAT
0
0.5
1
1.5
2
2.5
0
0.5
1
2
2.5
0
5
15
20
25
10
OUTPUT CURRENT (mA)
OUTPUT LOAD CURRENT (mA)
LOAD CURRENT (mA)
4088 G10
4088 G11
4088 G12
Battery Charge Current vs
Temperature
Battery Charger Float Voltage vs
Temperature
Low-Battery (Instant-On) Output
Voltage vs Temperature
3.68
3.66
3.64
3.62
3.60
4.21
4.20
4.19
4.18
4.17
600
500
400
300
200
100
0
V
= 2.7V
BAT
OUT
I
= 100mA
5x MODE
THERMAL REGULATION
60 80
20 40
TEMPERATURE (°C)
–40
–15
35
TEMPERATURE (°C)
60
85
–40
–15
10
35
60
85
–40 –20
0
100 120
10
TEMPERATURE (°C)
4088 G15
4088 G14
4088 G13
Oscillator Frequency vs
Temperature
VBUS Quiescent Current vs
Temperature
Quiescent Current in Suspend vs
Temperature
46
44
15
12
9
2.35
2.30
2.25
2.20
2.15
2.10
V
I
= 5V
V
I
= 5V
= 0µA
BUS
OUT
BUS
OUT
= 0mA
5x MODE
SUSP HI
42
40
38
36
34
1x MODE
6
3
–40
–15
10
35
60
85
–40
–15
10
35
60
85
–40
–15
10
35
60
85
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
4088 G18
4088 G16
4088 G17
4088fb
6
LTC4088
TA = 25°C, unless otherwise noted.
Typical perForMance characTerisTics
CHRG Pin Current vs Voltage
(Pull-Down State)
3.3V LDO Transient Response
(5mA to 15mA)
Suspend LDO Transient Response
(500µA to 1mA)
100
80
60
40
20
0
V
V
= 5V
BUS
BAT
= 3.8V
I
I
LDO3V3
OUT
5mA/DIV
500µA/DIV
0mA
0mA
V
OUT
V
LDO3V3
20mV/DIV
20mV/DIV
AC-COUPLED
AC COUPLED
4088 G20
4088 G21
V
BAT
= 3.8V
20µs/DIV
500µs/DIV
0
1
2
3
4
5
CHRG PIN VOLTAGE (V)
4088 G19
pin FuncTions
NTC (Pin 1): Input to the NTC Thermistor Monitoring
Circuits. The NTC pin connects to a negative temperature
coefficient thermistor which is typically co-packaged with
the battery pack to determine if the battery is too hot or
too cold to charge. If the battery’s temperature is out of
range, chargingispauseduntilthebatterytemperaturere-
enters the valid range. A low drift bias resistor is required
LDO3V3 (Pin 3): LDO Output. The LDO3V3 pin provides
a regulated, always-on 3.3V supply voltage. This pin gets
its power from V . It may be used for light loads such
OUT
as a real-time clock or housekeeping microprocessor. A
1µF capacitor is required from LDO3V3 to ground if it will
be called upon to deliver current. If the LDO3V3 output is
not used it should be disabled by connecting it to V
.
OUT
from V
to NTC and a thermistor is required from NTC
BUS
D2 (Pin 4): Mode Select Input Pin. D2, in combination
with the D0 pin and D1 pin, controls the current limit and
battery charger functions of the LTC4088 (see Table 1).
This pin is pulled low by a weak current sink.
to ground. If the NTC function is not desired, the NTC pin
should be grounded.
CLPROG (Pin 2): USB Current Limit Program and Monitor
Pin. A 1% resistor from CLPROG to ground determines
C/X(Pin5):EndofChargeIndicationProgramPin.Thispin
is used to program the current level at which a completed
charge cycle is indicated by the CHRG pin.
the upper limit of the current drawn from the V
pin.
BUS
, is sent
A precise fraction of the input current, h
CLPROG
to the CLPROG pin when the high side switch is on. The
switching regulator delivers power until the CLPROG
pin reaches 1.188V. Therefore, the current drawn from
PROG (Pin 6): Charge Current Program and Charge Cur-
rent Monitor Pin. Connecting a 1% resistor from PROG
to ground programs the charge current. If sufficient input
powerisavailableinconstant-currentmode,thispinservos
to 1V. The voltage on this pin always represents the actual
charge current by using the following formula:
V
will be limited to an amount given by h
CLPROG
and
available,
BUS
R
CLPROG
. There are several ratios for h
CLPROG
two of which correspond to the 500mA and 100mA USB
specifications. A multilayer ceramic averaging capacitor
is also required at CLPROG for filtering.
V
PROG
IBAT
=
•1031
RPROG
4088fb
7
LTC4088
pin FuncTions
CHRG (Pin 7): Open-Drain Charge Status Output. The
CHRG pin indicates the status of the battery charger. Four
possible states are represented by CHRG: charging, not
charging (or float charge current less than programmed
endofchargeindicationcurrent),unresponsivebatteryand
battery temperature out of range. CHRG is modulated at
35kHz and switches between a low and a high duty cycle
foreasyrecognitionbyeitherhumansormicroprocessors.
CHRG requires a pull-up resistor and/or LED to provide
indication.
BAT to V
ensures that V
is powered even if the load
OUT
OUT
exceeds the allotted power from V
or if the V
power
BUS
BUS
source is removed. V
impedance multilayer ceramic capacitor.
should be bypassed with a low
OUT
V
(Pin 11): Input voltage for the switching PowerPath
BUS
controller. V
will usually be connected to the USB port
BUS
of a computer or a DC output wall adapter. V
should
BUS
be bypassed with a low impedance multilayer ceramic
capacitor.
SW (Pin 12): The SW pin delivers power from V
to
BUS
GATE (Pin 8): Ideal Diode Amplifier Output. This pin con-
trols the gate of an optional external P-channel MOSFET
transistorused to supplement theinternalidealdiode. The
source of the P-channel MOSFET should be connected to
V
via the step-down switching regulator. An inductor
OUT
should be connected from SW to V . See the Applica-
OUT
tions Information section for a discussion of inductance
value and current rating.
V
OUT
and the drain should be connected to BAT.
D0 (Pin 13): Mode Select Input Pin. D0, in combination
with the D1 pin and the D2 pin, controls the current limit
andbatterychargerfunctionsoftheLTC4088(seeTable 1).
This pin is pulled low by a weak current sink.
BAT (Pin 9): Single Cell Li-Ion Battery Pin. Depending on
availablepowerandload,aLi-IonbatteryonBAT willeither
deliver system power to V
be charged from the battery charger.
through the ideal diode or
OUT
D1 (Pin 14): Mode Select Input Pin. D1, in combination
with the D0 pin and the D2 pin, controls the current limit
andbatterychargerfunctionsoftheLTC4088(seeTable 1).
This pin is pulled low by a weak current sink.
V
(Pin 10): Output voltage of the switching PowerPath
OUT
controller and input voltage of the battery charger. The
majority of the portable product should be powered from
V
. The LTC4088 will partition the available power be-
OUT
Exposed Pad (Pin 15): GND. Must be soldered to the
PCB to provide a low electrical and thermal impedance
connection to ground.
tween the external load on V
and the internal battery
OUT
charger. Priority is given to the external load and any extra
power is used to charge the battery. An ideal diode from
4088fb
8
LTC4088
block DiagraM
4088fb
9
LTC4088
operaTion
Introduction
Input Current Limited Step Down Switching Regulator
The power delivered from V to V is controlled by a
2.25MHz constant frequency step-down switching regu-
lator. To meet the USB maximum load specification, the
switching regulator contains a measurement and control
systemthatensuresthattheaverageinputcurrentremains
The LTC4088 includes a PowerPath controller, battery
charger, internal ideal diode, optional external ideal diode
controller, SUSPEND LDO and an always-on 3.3V LDO.
DesignedspecificallyforUSBapplications,thePowerPath
controller incorporates a precision average input current
limited step-down switching regulator to make maximum
use of the allowable USB power. Because power is con-
served, the LTC4088 allows the load current on V
exceed the current drawn by the USB port without exceed-
ing the USB load specifications.
BUS
OUT
below the level programmed at CLPROG. V
drives the
OUT
combination of the external load and the battery charger.
to
OUT
If the combined load does not cause the switching power
supply to reach the programmed input current limit, V
OUT
will track approximately 0.3V above the battery voltage.
By keeping the voltage across the battery charger at this
low level, power lost to the battery charger is minimized.
Figure 1 shows the power path components.
Theswitchingregulatorandbatterychargercommunicate
to ensure that the average input current never exceeds the
USB specifications.
The ideal diodes from BAT to V
guarantee that ample
even if there is insuf-
If the combined external load plus battery charge current
is large enough to cause the switching power supply to
reach the programmed input current limit, the battery
charger will reduce its charge current by precisely the
amount necessary to enable the external load to be satis-
fied. Even if the battery charge current is programmed to
exceed the allowable USB current, the USB specification
for average input current will not be violated; the battery
charger will reduce its current as needed. Furthermore, if
OUT
OUT
.
power is always available to V
ficient or absent power at V
BUS
To prevent battery drain when a device is connected to a
suspended USB port, an LDO from V to V provides
either low power or high power suspend current to the
application.
BUS
OUT
Finally, an “always on” LDO provides a regulated 3.3V
from V . This LDO will be on at all times and can be
the load current at V
exceeds the programmed power
OUT
OUT
used to supply up to 25mA to a system microprocessor.
SYSTEM LOAD
TO USB
OR WALL
ADAPTER
V
BUS
SW
3.5V TO
11
12
10
(BAT + 0.3V)
I
/N
SWITCH
V
OUT
PWM AND
GATE DRIVE
IDEAL
OPTIONAL
DIODE
EXTERNAL
IDEAL DIODE
PMOS
+
–
GATE
BAT
CONSTANT CURRENT
CONSTANT VOLTAGE
BATTERY CHARGER
OV
8
9
–
+
15mV
–
+
–
+
+
0.3V
CLPROG
1.188V
2
+
–
3.6V
AVERAGE INPUT
CURRENT LIMIT
CONTROLLER
AVERAGE OUTPUT
VOLTAGE LIMIT
CONTROLLER
+
SINGLE CELL
Li-Ion
4088 F01
Figure 1
4088fb
10
LTC4088
operaTion
Table 1. Controlled Input Current Limit
CHARGER
from V , load current will be drawn from the battery via
BUS
the ideal diodes even when the battery charger is enabled.
D0
D1
D2
STATUS
I
BUS(LIM)
The current at CLPROG is a precise fraction of the V
BUS
0
0
0
On
100mA (1x)
100mA (1x)
current. When a programming resistor and an averaging
capacitorareconnectedfromCLPROGtoGND,thevoltage
on CLPROG represents the average input current of the
switching regulator. As the input current approaches the
programmed limit, CLPROG reaches 1.188V and power
delivered by the switching regulator is held constant.
Several ratios of current are available which can be set
to correspond to USB low and high power modes with a
single programming resistor.
0
0
1
Off
0
1
0
On
500mA (5x)
0
1
1
Off
500mA (5x)
1
0
0
On
1A (10x)
1
0
1
Off
1A (10x)
1
1
0
Off
500µA (Susp Low)
2.5mA (Susp High)
1
1
1
Off
above the voltage at BAT. However, if the voltage at BAT
is below 3.3V, and the load requirement does not cause
the switching regulator to exceed its current limit, V
will regulate at a fixed 3.6V as shown in Figure 2. This will
allow a portable product to run immediately when power
is applied without waiting for the battery to charge.
The input current limit is programmed by various com-
binations of the D0, D1 and D2 pins as shown in Table 1.
The switching input regulator can also be deactivated
(USB Suspend).
OUT
The average input current will be limited by the CLPROG
programming resistor according to the following expres-
sion:
If the load does exceed the current limit at V , V
will
BUS OUT
range between the no-load voltage and slightly below the
batteryvoltage,indicatedbytheshadedregionofFigure 2.
VCLPROG
RCLPROG
IVBUS = IBUSQ
+
• h
+ 1
Ifthereisnobatterypresentwhenthishappens, V may
CLPROG
OUT
collapse to ground.
where I
CLPROG
is the quiescent current of the LTC4088,
The voltage regulation loop compensation is controlled by
BUSQ
V
is the CLPROG servo voltage in current limit,
the capacitance on V . An MLCC capacitor of 10µF is
OUT
R
is the value of the programming resistor and
required for loop stability. Additional capacitance beyond
this value will improve transient response.
CLPROG
h
is the ratio of the measured current at V
to
BUS
CLPROG
the sample current delivered to CLPROG. Refer to the
4.5
4.2
3.9
Electrical Characteristics table for values of h
,
CLPROG
V
and I
. Given worst-case circuit tolerances,
CLPROG
BUSQ
the USB specification for the average input current of 1x
or 5x mode will not be violated, provided that R
2.94k or greater.
is
CLPROG
NO LOAD
3.6
300mV
3.3
Table 1 shows the available settings for the D0, D1 and
D2 pins.
3.0
2.7
2.4
Notice that when D0 is high and D1 is low, the switching
regulator is set to a higher current limit for increased
3.6
4.2
2.4
2.7
3.0
3.3
3.9
charging and power availability at V . These modes
OUT
BAT (V)
will typically be used when there is line power available
4088 F02
from a wall adapter.
Figure 2. VOUT vs BAT
While not in current limit, the switching regulator’s
Bat-Track feature will set V
to approximately 300mV
OUT
4088fb
11
LTC4088
operaTion
Ideal Diode from BAT to V
connected to BAT. Capable of driving a 1nF load, the GATE
pin can control an external P-channel MOSFET transistor
OUT
The LTC4088 has an internal ideal diode as well as a
controller for an optional external ideal diode. Both the
internal and the external ideal diodes are always on and
having an on-resistance of 30mΩ or lower. When V
is
BUS
unavailable,theforwardvoltageoftheidealdiodeamplifier
will be reduced from 15mV to nearly zero.
will respond quickly whenever V
drops below BAT.
OUT
If the load current increases beyond the power allowed
from the switching regulator, additional power will be
pulled from the battery via the ideal diodes. Furthermore,
Suspend LDO
The LTC4088 provides a small amount of power to V
SUSPEND mode by including an LDO from V
in
OUT
OUT
to V
.
BUS
if power to V
(USB or wall power) is removed, then all
BUS
ThisLDOwillpreventthebatteryfromrunningdownwhen
the portable product has access to a suspended USB port.
Regulating at 4.6V, this LDO only becomes active when
the switching converter is disabled. To remain compliant
with the USB specification, the input to the LDO is current
limited so that it will not exceed the low power or high
of the application power will be provided by the battery via
the ideal diodes. The ideal diodes will be fast enough to
keepV fromdroopingwithonlythestoragecapacitance
OUT
required for the switching regulator. The internal ideal
diode consists of a precision amplifier that activates a
large on-chip MOSFET transistor whenever the voltage at
power suspend specification. If the load on V
exceeds
OUT
V
is approximately 15mV (V ) below the voltage at
OUT
FWD
the suspend current limit, the additional current will come
from the battery via the ideal diodes. The suspend LDO
BAT. Within the amplifier’s linear range, the small-signal
resistance of the ideal diode will be quite low, keeping
the forward drop near 15mV. At higher current levels, the
MOSFET will be in full conduction. The on-resistance in
this case is approximately 180mΩ. If this is sufficient for
the application, then no external components are neces-
sary. However, ifmoreconductanceisneeded, anexternal
P-channel MOSFET transistor can be added from BAT to
sends a scaled copy of the V
current to the CLPROG
BUS
pin,whichwillservotoapproximately100mVinthismode.
Thus, the high power and low power suspend settings are
related to the levels programmed by the same resistor for
1x and 5x modes.
3.3V Always-On Supply
V . The GATE pin of the LTC4088 drives the gate of the
OUT
The LTC4088 includes an ultralow quiescent current low
dropout regulator that is always powered. This LDO can
be used to provide power to a system pushbutton control-
ler or standby microcontroller. Designed to deliver up to
25mA, the always-on LDO requires a 1µF MLCC bypass
capacitor for compensation. The LDO is powered from
P-channel MOSFET transistor for automatic ideal diode
control. The source of the external P-channel MOSFET
should be connected to V
and the drain should be
OUT
2200
VISHAY Si2333
OPTIONAL EXTERNAL
IDEAL DIODE
2000
1800
1600
1400
1200
1000
800
V
, and therefore will enter dropout at loads less than
OUT
25mA as V
falls near 3.3V. If the LDO3V3 output is
OUT
not used, it should be disabled by connecting it to V
.
LTC4088
IDEAL DIODE
OUT
V
BUS
Undervoltage Lockout (UVLO)
600
ON
SEMICONDUCTOR
MBRM120LT3
AninternalundervoltagelockoutcircuitmonitorsV and
BUS
400
keepstheswitchingregulatoroffuntilV
risesabovethe
BUS
200
V
= 5V
BUS
risingUVLOthreshold(4.3V).IfV
fallsbelowthefalling
BUS
0
0
120 180 240 300 360 420 480
FORWARD VOLTAGE (mV) (BAT – V
60
UVLO threshold (4V), system power at V
will be drawn
OUT
)
OUT
from the battery via the ideal diodes. The voltage at V
BUS
4088 F03
must also be higher than the voltage at BAT by approxi-
Figure 3. Ideal Diode V-I Characteristics
mately170mVfortheswitchingregulatortooperate.
4088fb
12
LTC4088
operaTion
Battery Charger
cally begin when the battery voltage falls below V
RECHRG
(typically4.1V).Intheeventthatthesafetytimerisrunning
TheLTC4088includesaconstant-current/constant-voltage
battery charger with automatic recharge, automatic ter-
mination by safety timer, low voltage trickle charging,
bad cell detection and thermistor sensor input for out of
temperature charge pausing.
when the battery voltage falls below V
, it will reset
RECHRG
back to zero. To prevent brief excursions below V
RECHRG
fromresettingthesafetytimer,thebatteryvoltagemustbe
belowV formorethan1.5ms. Thechargecycleand
RECHRG
safety timer will also restart if the V
UVLO cycles low
BUS
When a battery charge cycle begins, the battery charger
first determines if the battery is deeply discharged. If the
batteryvoltageisbelowV
trickle charge feature sets the battery charge current to
10% of the programmed value. If the low voltage persists
for more than 1/2 hour, the battery charger automatically
terminatesandindicates,viatheCHRGpin,thatthebattery
was unresponsive.
and then high (e.g., V
is removed and then replaced)
BUS
or if the charger is momentarily disabled using the D2 pin.
,typically2.85V,anautomatic
TRKL
Charge Current
The charge current is programmed using a single resistor
from PROG to ground. 1/1031th of the battery charge cur-
rent is delivered to PROG, which will attempt to servo to
1.000V. Thus, the battery charge current will try to reach
1031 times the current in the PROG pin. The program
resistor and the charge current are calculated using the
following equations:
Once the battery voltage is above V
, the charger be-
TRKL
gins charging in full power constant-current mode. The
current delivered to the battery will try to reach 1031V/
R . Depending on available input power and external
PROG
1031V
ICHG
1031V
RPROG
RPROG
=
, ICHG =
load conditions, the battery charger may or may not be
able to charge at the full programmed rate. The external
load will always be prioritized over the battery charge
current. The USB current limit programming will always
be observed and only additional power will be available to
charge the battery. When system loads are light, battery
charge current will be maximized.
Ineithertheconstant-currentorconstant-voltagecharging
modes, the voltage at the PROG pin will be proportional
to the actual charge current delivered to the battery. The
chargecurrentcanbedeterminedatanytimebymonitoring
the PROG pin voltage and using the following equation:
Charge Termination
VPROG
IBAT
=
•1031
The battery charger has a built-in safety timer. Once the
voltage on the battery reaches the pre-programmed float
voltage of 4.200V, the charger will regulate the battery
voltagethereandthechargecurrentwilldecreasenaturally.
Once the charger detects that the battery has reached
4.200V, the 4-hour safety timer is started. After the safety
timer expires, charging of the battery will discontinue and
no more current will be delivered.
RPROG
In many cases, the actual battery charge current, I
,
BAT
will be lower than the programmed current, I , due
CHG
to limited input power available and prioritization to the
system load drawn from V
.
OUT
Charge Status Indication
The CHRG pin indicates the status of the battery charger.
Four possible states are represented by CHRG which
include charging, not charging (or float charge current
less than programmed end of charge indication current),
unresponsivebatteryandbatterytemperatureoutofrange.
Automatic Recharge
Once the battery charger terminates, it will remain off
drawing only microamperes of current from the battery.
If the portable product remains in this state long enough,
thebatterywilleventuallyselfdischarge.To ensurethatthe
battery is always topped off, a charge cycle will automati-
The signal at the CHRG pin can be easily recognized
as one of the above four states by either a human or a
4088fb
13
LTC4088
operaTion
microprocessor. An open-drain output, the CHRG pin can
drive an indicator LED through a current limiting resis-
tor for human interfacing or simply a pull-up resistor for
microprocessor interfacing.
If a battery is found to be unresponsive to charging (i.e.,
its voltage remains below 2.85V for 1/2 hour), the CHRG
pin gives the battery fault indication. For this fault, a hu-
manwouldeasilyrecognizethefrantic6.1Hz“fast”blinkof
the LED while a microprocessor would be able to decode
either the 12.5% or 87.5% duty cycles as a bad cell fault.
To make the CHRG pin easily recognized by both humans
and microprocessors, the pin is either a DC signal of ON
for charging, OFF for not charging or it is switched at high
frequency(35kHz)toindicatethetwopossiblefaults.While
switching at 35kHz, its duty cycle is modulated at a slow
rate that can be recognized by a human.
Because the LTC4088 is a 3-terminal PowerPath product,
system load is always prioritized over battery charging.
Due to excessive system load, there may not be sufficient
power to charge the battery beyond the bad cell threshold
voltage within the bad cell timeout period. In this case the
battery charger will falsely indicate a bad cell. System
software may then reduce the load and reset the battery
charger to try again.
Whenchargingbegins,CHRGispulledlowandremainslow
for the duration of a normal charge cycle. When charging
is complete, as determined by the criteria set by the C/X
pin, the CHRG pin is released (Hi-Z). The CHRG pin does
not respond to the C/X threshold if the LTC4088 is in V
Although very improbable, it is possible that a duty cycle
reading could be taken at the bright-dim transition (low
duty cycle to high duty cycle). When this happens the
duty cycle reading will be precisely 50%. If the duty cycle
reading is 50%, system software should disqualify it and
take a new duty cycle reading.
BUS
current limit. This prevents false end of charge indications
duetoinsufficientpoweravailabletothebatterycharger.If
afault occurswhilecharging, thepinisswitchedat35kHz.
Whileswitching,itsdutycycleismodulatedbetweenahigh
and low value at a very low frequency. The low and high
duty cycles are disparate enough to make an LED appear
to be on or off thus giving the appearance of “blinking”.
Each of the two faults has its own unique “blink” rate for
human recognition as well as two unique duty cycles for
machine recognition.
C/X Determination
The current exiting the C/X pin represents 1/1031th of
the battery charge current. With a resistor from C/X to
ground that is X/10 times the resistor at the PROG pin,
the CHRG pin releases when the battery current drops to
Table 2 illustrates the four possible states of the CHRG
pin when the battery charger is active.
C/X. For example, if C/10 detection is desired, R should
C/X
be made equal to R
PROG
state is given by:
. For C/20, R would be twice
. The current threshold at which CHRG will change
PROG
C/X
Table 2. CHRG Signal
R
MODULATION
DUTY
CYCLES
STATUS
FREQUENCY (BLINK) FREQUENCY
VC/X
RC/X
Charging
0Hz
0Hz
0Hz (Low Z)
0Hz (Hi-Z)
100%
0%
IBAT
=
•1031
I
< C/X
BAT
NTC Fault
35kHz
35kHz
1.5Hz at 50%
6.1Hz at 50%
6.25% or 93.75%
12.5% or 87.5%
With this design, C/10 detection can be achieved with only
one resistor rather than a resistor for both the C/X pin and
the PROG pin. Since both of these pins have 1/1031 of
the battery charge current in them, their voltages will be
equal when they have the same resistor value. Therefore,
rather than using two resistors, the C/X pin and the PROG
pin can be connected together and the resistors can be
paralleledtoasingleresistorof1/2oftheprogramresistor.
Bad Battery
Notice that an NTC fault is represented by a 35kHz pulse
trainwhosedutycycletogglesbetween6.25%and93.75%
at a 1.5Hz rate. A human will easily recognize the 1.5Hz
rate as a “slow” blinking which indicates the out of range
battery temperature while a microprocessor will be able
to decode either the 6.25% or 93.75% duty cycles as an
NTC fault.
4088fb
14
LTC4088
operaTion
NTC Thermistor
Thermal Regulation
Thebatterytemperatureismeasuredbyplacinganegative
temperature coefficient (NTC) thermistor close to the bat-
terypack.TheNTCcircuitryisshownintheBlockDiagram.
To prevent thermal damage to the IC or surrounding
components, an internal thermal feedback loop will
automatically decrease the programmed charge current
if the die temperature rises to approximately 110°C.
Thermal regulation protects the LTC4088 from excessive
temperature due to high power operation or high ambient
thermal conditions, and allows the user to push the limits
of the power handling capability with a given circuit board
design without risk of damaging the LTC4088 or external
components. The benefit of the LTC4088 thermal regula-
tion loop is that charge current can be set according to
actual conditions rather than worst-case conditions for a
given application with the assurance that the charger will
automaticallyreducethecurrentinworst-caseconditions.
To use this feature, connect the NTC thermistor, R
,
,
NTC
betweentheNTCpinandgroundandabiasresistor,R
NOM
from V
to NTC. R
should be a 1% resistor with
BUS
NOM
a value equal to the value of the chosen NTC thermistor
at 25°C (R25). A 100k thermistor is recommended since
thermistor current is not measured by the LTC4088 and
will have to be considered for USB compliance.
The LTC4088 will pause charging when the resistance of
theNTCthermistordropsto0.54timesthevalueofR25or
approximately 54k (for a Vishay “Curve 1” thermistor, this
correspondstoapproximately40°C).Ifthebatterycharger
is in constant voltage (float) mode, the safety timer also
pauses until the thermistor indicates a return to a valid
temperature. As the temperature drops, the resistance of
the NTC thermistor rises. The LTC4088 is also designed
to pause charging when the value of the NTC thermistor
increases to 3.25 times the value of R25. For a Vishay
“Curve 1” thermistor, this resistance, 325k, corresponds
to approximately 0°C. The hot and cold comparators each
haveapproximately3°Cofhysteresistopreventoscillation
about the trip point. Grounding the NTC pin disables all
NTC functionality.
Shutdown Mode
For autonomous battery charger operation, D2 should
be permanently grounded. However, for more control
via software the LTC4088’s battery charger can be inde-
pendently disabled by bringing the D2 pin above V . D2
IH
must also be brought high to enable high power (2.5mA)
suspend mode.
The input switching regulator is enabled whenever V
BUS
is above the UVLO voltage and the LTC4088 is not in one
of the two USB suspend modes (500µA or 2.5mA).
The ideal diode is enabled at all times and cannot be
disabled.
4088fb
15
LTC4088
applicaTions inForMaTion
CLPROG Resistor and Capacitor
rectifier as current approaches zero. This comparator will
minimizetheeffectofcurrentreversalontheaverageinput
current measurement. For some low inductance values,
however, the inductor current may reverse slightly. This
value depends on the speed of the comparator in relation
As described in the Step-Down Input Regulator section,
the resistor on the CLPROG pin determines the average
input current limit in each of the six current limit modes.
The input current will be comprised of two components,
to the slope of the current waveform, given by V /L, where
L
the current that is used to drive V
and the quiescent
OUT
V isthevoltageacrosstheinductor(approximately–V
)
L
OUT
current of the switching regulator. To ensure that the USB
specificationisstrictlymet, bothcomponentsofinputcur-
rent should be considered. The Electrical Characteristics
table gives the typical values for quiescent currents in all
settings as well as current limit programming accuracy.
To get as close to the 500mA or 100mA specifications as
possible, a precision resistor should be used.
and L is the inductance value.
An inductance value of 3.3µH is a good starting value. The
ripple will be small enough for the regulator to remain in
continuousconductionat100mAaverageV
current.At
BUS
lighter loads the current-reversal comparator will disable
thesynchronousrectifieratacurrentslightlyabove0mA.As
theinductanceisreducedfromthisvalue,thepartwillenter
discontinuous conduction mode at progressively higher
An averaging capacitor is required in parallel with the
resistor so that the switching regulator can determine
the average input current. This capacitor also provides
the dominant pole for the feedback loop when current
limit is reached. To ensure stability, the capacitor on
CLPROG should be 0.47µF or larger. Alternatively, faster
transient response may be achieved with 0.1µF in series
with 8.2Ω.
loads. Ripple at V
will increase, directly proportionally
OUT
to the magnitude of inductor ripple. Transient response,
however, will be improved. The current mode controller
controls inductor current to exactly the amount required
by the load to keep V
in regulation. A transient load
OUT
steprequirestheinductorcurrenttochangetoanewlevel.
Since inductor current cannot change instantaneously,
the capacitance on V
delivers or absorbs the differ-
OUT
Choosing the Inductor
ence in current until the inductor current can change to
meet the new load demand. A smaller inductor changes
its current more quickly for a given voltage drive than a
larger inductor, resulting in faster transient response. A
largerinductorwillreduceoutputrippleandcurrentripple,
but at the expense of reduced transient performance (or
Becausetheaverageinputcurrentcircuitdoesnotmeasure
reverse current (i.e., current from V
to V ), cur-
OUT
BUS
rent reversal in the inductor at light loads will contribute
an error to the V current measurement. The error is
BUS
conservative in that if the current reverses, the voltage
at CLPROG will be higher than what would represent the
actual average input current drawn. The current available
for charging and the system load is thus reduced. The
USB specification will not be violated.
more C
required) and a physically larger inductor
VOUT
package size.
The input regulator has an instantaneous peak current
clamp to prevent the inductor from saturating during tran-
sient load or start-up conditions. The clamp is designed
so that it does not interfere with normal operation at
highloadswithreasonableinductorripple.Itwillprevent
inductor current runaway in case of a shorted output.
This reduction in available V
current will happen when
BUS
the peak-peak inductor ripple is greater than twice the
average current limit setting. For example, if the average
current limit is set to 100mA, the peak-peak ripple should
notexceed200mA. Iftheinputcurrentislessthan100mA,
the measurement accuracy may be reduced, but it does
not affect the average current loop since it will not be in
regulation.
The DC winding resistance and AC core losses of the
inductor will affect efficiency, and therefore available
output power. These effects are difficult to characterize
and vary by application. Some inductors which may be
suitable for this application are listed in Table 3.
TheLTC4088includesacurrent-reversalcomparatorwhich
monitors inductor current and disables the synchronous
4088fb
16
LTC4088
applicaTions inForMaTion
Table 3. Recommended Inductors for the LTC4088
L
(µH)
MAX IDC MAX DCR
SIZE IN mm
(L × W × H)
INDUCTOR TYPE
(A)
(Ω)
MANUFACTURER
LPS4018
3.3
2.2
0.08
3.9 × 3.9 × 1.7
Coilcraft
www.coilcraft.com
D53LC
DB318C
3.3
3.3
2.26
1.55
0.034
0.070
5 × 5 × 3
3.8 × 3.8 × 1.8
Toko
www.toko.com
WE-TPC Type M1
3.3
1.95
0.065
4.8 × 4.8 × 1.8
Wurth Elektronik
www.we-online.com
CDRH6D12
CDRH6D38
3.3
3.3
2.2
3.5
0.0625
0.020
6.7 × 6.7 × 1.5
7 × 7 × 4
Sumida
www.sumida.com
VBUS and VOUT Bypass Capacitors
Forexample,X7Rceramiccapacitorshavethebestvoltage
and temperature stability. X5R ceramic capacitors have
apparentlyhigherpackingdensitybutpoorerperformance
over their rated voltage and temperature ranges. Y5V
ceramic capacitors have the highest packing density,
but must be used with caution, because of their extreme
nonlinearcharacteristicofcapacitanceversusvoltage.The
actualin-circuitcapacitanceofaceramiccapacitorshould
be measured with a small AC signal and DC bias as is
expectedin-circuit.Manyvendorsspecifythecapacitance
verse voltage with a 1VRMS AC test signal and, as a result,
over state the capacitance that the capacitor will present
in the application. Using similar operating conditions as
the application, the user must measure or request from
the vendor the actual capacitance to determine if the
selected capacitor meets the minimum capacitance that
the application requires.
ThestyleandvalueofcapacitorsusedwiththeLTC4088
determineseveralimportantparameterssuchasregula-
tor control-loop stability and input voltage ripple. Be-
cause the LTC4088 uses a step-down switching power
supply from VBUS to VOUT, its input current waveform
contains high frequency components. It is strongly
recommended that a low equivalent series resistance
(ESR) multilayer ceramic capacitor be used to bypass
VBUS. Tantalum and aluminum capacitors are not rec-
ommended because of their high ESR. The value of the
capacitor on VBUS directly controls the amount of input
ripple for a given load current. Increasing the size of this
capacitorwillreducetheinputripple.TheUSBspecifica-
tion allows a maximum of 10µF to be connected directly
across the USB power bus. If additional capacitance is
required for noise performance, a soft-connect circuit
may be required to limit inrush current and avoid exces-
sive transient voltage drops on the bus (see Figure 5).
Overprogramming the Battery Charger
The USB high power specification allows for up to 2.5W
to be drawn from the USB port. The switching regulator
transforms the voltage at VBUS to just above the voltage
at BAT with high efficiency, while limiting power to less
than the amount programmed at CLPROG. The charger
should be programmed (with the PROG pin) to deliver the
maximumsafechargingcurrentwithoutregardtotheUSB
specifications. If there is insufficient current available to
charge the battery at the programmed rate, it will reduce
charge current until the system load on VOUT is satisfied
and the VBUS current limit is satisfied. Programming the
charger for more current than is available will not cause
theaverageinputcurrentlimittobeviolated. Itwillmerely
allow the battery charger to make use of all available
To prevent large VOUT voltage steps during transient
load conditions, it is also recommended that a ceramic
capacitor be used to bypass VOUT. The output capacitor
is used in the compensation of the switching regula-
tor. At least 10µF with low ESR are required on VOUT
.
Additional capacitance will improve load transient
performance and stability.
Multilayer ceramic chip capacitors typically have excep-
tional ESR performance. MLCCs combined with a tight
boardlayoutandanunbrokengroundplanewillyieldvery
good performance and low EMI emissions.
There are several types of ceramic capacitors avail-
able each having considerably different characteristics.
4088fb
17
LTC4088
applicaTions inForMaTion
power to charge the battery as quickly as possible, and
with minimal power dissipation within the charger.
The trip points for the LTC4088’s temperature qualifica-
tion are internally programmed at 0.349 • V for the hot
BUS
threshold and 0.765 • V
for the cold threshold.
BUS
Alternate NTC Thermistors and Biasing
Therefore, the hot trip point is set when:
RNTC|HOT
The LTC4088 provides temperature qualified charging if
a grounded thermistor and a bias resistor are connected
to NTC. By using a bias resistor whose value is equal to
the room temperature resistance of the thermistor (R25)
the upper and lower temperatures are pre-programmed
to approximately 40°C and 0°C, respectively (assuming
a Vishay “Curve 1” thermistor).
• V
= 0.349 • V
BUS
BUS
RNOM + RNTC|HOT
and the cold trip point is set when:
RNTC|COLD
• V
= 0.765 • V
BUS
BUS
RNOM + RNTC|COLD
The upper and lower temperature thresholds can be ad-
justed by either a modification of the bias resistor value
or by adding a second adjustment resistor to the circuit.
If only the bias resistor is adjusted, then either the upper
or the lower threshold can be modified but not both. The
other trip point will be determined by the characteristics
of the thermistor. Using the bias resistor in addition to an
adjustmentresistor,boththeupperandthelowertempera-
ture trip points can be independently programmed with
the constraint that the difference between the upper and
lower temperature thresholds cannot decrease. Examples
of each technique are given below.
Solving these equations for R
results in the following:
and R
NTC|HOT
NTC|COLD
R
= 0.536 • R
NTC|HOT
NOM
and
R
= 3.25 • R
NTC|COLD
NOM
By setting R
equal to R25, the above equations result
NOM
= 0.536 and r
in r
= 3.25. Referencing these ratios
HOT
COLD
to the Vishay Resistance-Temperature Curve 1 chart gives
a hot trip point of about 40°C and a cold trip point of about
0°C. The difference between the hot and cold trip points
is approximately 40°C.
NTC thermistors have temperature characteristics which
areindicatedonresistance-temperatureconversiontables.
The Vishay-Dale thermistor NTHS0603N01N1003, used
in the following examples, has a nominal value of 100k
and follows the Vishay “Curve 1” resistance-temperature
characteristic.
Byusingabiasresistor,R ,differentinvaluefromR25,
NOM
the hot and cold trip points can be moved in either direc-
tion. The temperature span will change somewhat due to
the non-linear behavior of the thermistor. The following
equations can be used to easily calculate a new value for
the bias resistor:
In the explanation below, the following notation is used.
R25 = Value of the Thermistor at 25°C
rHOT
0.536
rCOLD
RNOM
RNOM
=
=
•R25
•R25
R
R
= Value of thermistor at the cold trip point
NTC|COLD
= Value of the thermistor at the hot trip point
NTC|HOT
3.25
r
r
= Ratio of R
to R25
COLD
NTC|COLD
= Ratio of R
to R25
wherer andr
aretheresistanceratiosatthedesired
HOT
NTC|COLD
HOT
COLD
hot and cold trip points. Note that these equations are
linked. Therefore, only one of the two trip points can be
chosen, the other is determined by the default ratios de-
signed in the IC. Consider an example where a 60°C hot
trip point is desired.
R
=Primarythermistorbiasresistor(seeFigure2)
NOM
R1 = Optional temperature range adjustment resistor
(see Figure 3)
4088fb
18
LTC4088
applicaTions inForMaTion
FromtheVishayCurve1R-Tcharacteristics,r is0.2488
USB Inrush Limiting
HOT
at 60°C. Using the above equation, R
should be set to
, the cold trip point is about
NOM
TheUSBspecificationallowsatmost10µFofdownstream
capacitance to be hot-plugged into a USB hub. In most
LTC4088 applications, 10µF should be enough to provide
46.4k. With this value of R
NOM
16°C. Notice that the span is now 44°C rather than the
previous40°C. Thisisduetothedecreasein“temperature
gain”ofthethermistorasabsolutetemperatureincreases.
adequatefilteringonV .Ifmorecapacitanceisrequired,
BUS
thefollowingcircuitcanbeusedtosoft-connectadditional
The upper and lower temperature trip points can be inde-
pendentlyprogrammedbyusinganadditionalbiasresistor
asshowninFigure4b. Thefollowingformulascanbeused
capacitance.
In this circuit, capacitor C1 holds MP1 off when the cable
is first connected. Eventually the bottom plate of C1 dis-
chargestoGND, applyingincreasinggatesupporttoMP1.
The long time constant of R1 and C1 prevent the current
from building up in the cable too fast, thus dampening
out any resonant overshoot.
to compute the values of R
and R1:
NOM
rCOLD − rHOT
RNOM
=
•R25
2.714
R1= 0.536 •RNOM − rHOT •R25
For example, to set the trip points to 0°C and 45°C with
a Vishay Curve 1 thermistor choose:
MP1
Si2333
V
BUS
3.266 − 0.4368
C1
100nF
5V USB
INPUT
RNOM
=
•100k = 104.2k
2.714
LTC4088
USB CABLE
C2
R1
40k
the nearest 1% value is 105k:
GND
R1 = 0.536 • 105k – 0.4368 • 100k = 12.6k
4088 F05
the nearest 1% value is 12.7k. The final solution is shown
in Figure 4b and results in an upper trip point of 45°C and
a lower trip point of 0°C.
Figure 5. USB Soft-Connect Circuit
LTC4088
NTC BLOCK
V
V
BUS
LTC4088
NTC BLOCK
V
V
BUS
BUS
BUS
0.765 • V
0.765 • V
BUS
BUS
R
R
NOM
NOM
–
+
–
+
100k
105k
TOO_COLD
TOO_HOT
TOO_COLD
TOO_HOT
NTC
NTC
1
1
R
NTC
R1
12.7k
T
100k
–
+
–
+
0.349 • V
0.349 • V
BUS
BUS
R
NTC
T
100k
+
–
+
–
NTC_ENABLE
NTC_ENABLE
0.1V
0.1V
4088 F04a
4088 F04b
Figure 4. NTC Circuits
4088fb
19
LTC4088
applicaTions inForMaTion
Voltage overshoot on V
may sometimes be observed
BUS
when connecting the LTC4088 to a lab power supply. This
overshoot is caused by long leads from the power supply
to V . Twisting the wires together from the supply to
BUS
V
can greatly reduce the parasitic inductance of these
BUS
longleads,andkeepthevoltageatV
tosafelevels.USB
BUS
cables are generally manufactured with the power leads in
close proximity, and thus fairly low parasitic inductance.
4088 F06
Board Layout Considerations
Figure 6. Ground Currents Follow Their Incident Path
at High Speed. Slices in the Ground Plane Cause High
Voltage and Increased Emissions
The Exposed Pad on the backside of the LTC4088 pack-
age must be securely soldered to the PC board ground.
This is the only ground pin in the package, and it serves
as the return path for both the control circuitry and the
synchronous rectifier.
Battery Charger Stability Considerations
The LTC4088’s battery charger contains both a constant-
voltageandaconstant-currentcontrolloop.Theconstant-
voltage loop is stable without any compensation when a
battery is connected with low impedance leads. Excessive
leadlength,however,mayaddenoughseriesinductanceto
requireabypasscapacitorofatleast1µFfromBAT toGND.
Furthermore,duetoitshighfrequencyswitchingcircuitry,
it is imperative that the input capacitor, inductor, and
output capacitor be as close to the LTC4088 as possible
and that there be an unbroken ground plane under the
LTC4088andallofitsexternalhighfrequencycomponents.
High frequency currents, such as the input current on the
LTC4088, tend to find their way on the ground plane along
a mirror path directly beneath the incident path on the top
of the board. If there are slits or cuts in the ground plane
due to other traces on that layer, the current will be forced
to go around the slits. If high frequency currents are not
allowed to flow back through their natural least-area path,
excessive voltage will build up and radiated emissions will
occur(seeFigure6).Thereshouldbeagroupofviasdirectly
under the grounded backside leading directly down to an
internal ground plane. To minimize parasitic inductance,
the ground plane should be as close as possible to the
top plane of the PC board (layer 2).
High value, low ESR multilayer ceramic chip capacitors
reduce the constant-voltage loop phase margin, possibly
resulting in instability. Ceramic capacitors up to 22µF
may be used in parallel with a battery, but larger ceramics
should bedecoupled with0.2Ω to 1Ω of series resistance.
Furthermore, a4.7µF capacitorinserieswitha0.2Ω to1Ω
resistor from BAT to GND is required to prevent oscillation
when the battery is disconnected.
In constant-current mode, the PROG pin is in the feed-
back loop rather than the battery voltage. Because of the
additional pole created by any PROG pin capacitance,
capacitance on this pin must be kept to a minimum. With
no additional capacitance on the PROG pin, the charger
is stable with program resistor values as high as 25k.
However, additional capacitance on this node reduces the
maximumallowedprogramresistor.Thepolefrequencyat
the PROG pin should be kept above 100kHz. Therefore, if
The GATE pin for the external ideal diode controller has
extremely limited drive current. Care must be taken to
minimize leakage to adjacent PC board traces. 100nA of
leakage from this pin will introduce an additional offset
to the ideal diode of approximately 10mV. To minimize
leakage, the trace can be guarded on the PC board by
the PROG pin has a parasitic capacitance, C
, the fol-
PROG
lowing equation should be used to calculate the maximum
surrounding it with V
connected metal, which should
OUT
resistance value for R
:
PROG
generally be less than one volt higher than GATE.
1
RPROG
≤
2π •100kHz •CPROG
4088fb
20
LTC4088
Typical applicaTions
High Efficiency Battery Charger/USB Power Manager
with NTC Qualified Charging and Reverse Input Protection
L1
WALL
USB
3.3µH
M2
V
SW
V
LOAD
BUS
OUT
D0
D1
D2
CHRG
LDO3V3
GATE
BAT
R1
100k
LTC4088
M1
µC
C1
10µF
0805
C3
10µF
0805
NTC
CLPROG PROG C/X GND
+
Li-Ion
R2
T
R5
8.2Ω
R3
2.94k
100k
R4
499Ω
C2
0.1µF
0603
4088 TA02
C1, C3: MURATA GRM21BR61A106KE19
C2: MURATA GRM188R71C104KA01
L1: COILCRAFT LPS4018-332MLC
M1, M2: SILICONIX Si2333
R2: VISHAY-DALE NTHS0603N01N1003
USB Compliant Switching Charger
L1
WALL
USB
3.3µH
V
SW
V
BUS
OUT
LDO3V3
GATE
C3
10µF
0805
D0
D1
D2
CHRG
R1
100k
LTC4088
µC
C1
10µF
0805
LOAD
BAT
NTC
CLPROG PROG C/X GND
+
Li-Ion
R2
T
R5
8.2Ω
R3
2.94k
100k
R4
499Ω
C2
0.1µF
0603
4088 TA03a
C1, C3: MURATA GRM21BR61A106KE19
C2: MURATA GRM188R71C104KA01
L1: COILCRAFT LPS4018-332MLC
R2: VISHAY-DALE NTHS0603N01N1003
700
I
BAT
600
500
400
300
200
100
0
I
BUS
5x USB SETTING,
BATTERY CHARGER SET FOR 1A
3.0 3.3 3.6
BATTERY VOLTAGE (V)
4.2
2.7
3.9
4088 TA03b
4088fb
21
LTC4088
package DescripTion
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
DE Package
14-Lead Plastic DFN (4mm × 3mm)
(Reference LTC DWG # 05-08-1708 Rev B)
0.70 ±0.05
3.30 ±0.05
1.70 ±0.05
3.60 ±0.05
2.20 ±0.05
PACKAGE
OUTLINE
0.25 ±0.05
0.50 BSC
3.00 REF
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
R = 0.115
TYP
0.40 ±0.10
4.00 ±0.10
(2 SIDES)
8
14
R = 0.05
TYP
3.30 ±0.10
3.00 ±0.10
(2 SIDES)
1.70 ±0.10
PIN 1 NOTCH
R = 0.20 OR
PIN 1
TOP MARK
(SEE NOTE 6)
0.35 × 45°
CHAMFER
(DE14) DFN 0806 REV B
7
1
0.25 ±0.05
0.75 ±0.05
0.200 REF
0.50 BSC
3.00 REF
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WGED-3) IN JEDEC
PACKAGE OUTLINE MO-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
4088fb
22
LTC4088
revision hisTory (Revision history begins at Rev B)
REV
DATE
DESCRIPTION
PAGE NUMBER
B
05/12 Clarified thermistor part number.
18, 21
4088fb
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
23
LTC4088
relaTeD parTs
PART NUMBER
Battery Chargers
LTC4057
DESCRIPTION
COMMENTS
Lithium-Ion Linear Battery Charger
Up to 800mA Charge Current, Thermal Regulation, ThinSOT™ Package
C/10 Charge Termination, Battery Kelvin Sensing, 7% Charge Accuracy
2mm × 2mm DFN Package, Thermal Regulation, Standalone Operation
LTC4058
Standalone 950mA Lithium-Ion Charger in DFN
750mA Linear Lithium-Ion Battery Charger
LTC4065/LTC4065A
LTC4411/LTC4412
Low Loss Single PowerPath Controllers in
ThinSOT
Automatic Switching Between DC Sources, Load Sharing,
Replaces ORing Diodes
LTC4413
Dual Ideal Diodes
3mm × 3mm DFN Package, Low Loss Replacement for ORing Diodes
Power Management
LTC3406/LTC3406A
600mA (I ), 1.5MHz, Synchronous
95% Efficiency, V = 2.5V to 5.5V, V
= 0.6V, I = 20µA, I < 1µA,
Q SD
OUT
IN
OUT
Step-Down DC/DC Converter
ThinSOT Package
LTC3411
LTC3455
LTC4055
LTC4066
LTC4085
1.25A (I ), 4MHz, Synchronous Step-Down
95% Efficiency, V = 2.5V to 5.5V, V
= 0.8V, I = 60µA, I < 1µA,
Q SD
OUT
IN
OUT
DC/DC Converter
MS10 Package
Dual DC/DC Converter with USB Power Manager
and Li-Ion Battery Charger
Seamless Transition Between Power Sources: USB, Wall Adapter and
Battery; 95% Efficient DC/DC Conversion
USB Power Controller and Battery Charger
Charges Single Cell Li-Ion Batteries Directly from a USB Port, Thermal
Regulation, 200mΩ Ideal Diode, 4mm × 4mm QFN16 Package
USB Power Controller and Battery Charger
Charges Single Cell Li-Ion Batteries Directly from a USB Port, Thermal
Regulation, 50mΩ Ideal Diode, 4mm × 4mm QFN24 Package
USB Power Manager with Ideal Diode Controller
and Li-Ion Charger
Charges Single Cell Li-Ion Batteries Directly from a USB Port, Thermal
Regulation, 200mΩ Ideal Diode with <50mΩ Option, 4mm × 3mm
DFN14 Package
LTC4088-1
High Efficiency USB Power Manager and Battery
Charger with Regulated Output Voltage
Maximizes Available Power from USB Port, Bat-Track, “Instant-On”
Operation, 1.5A Max Charge Current, 180mΩ Ideal Diode with <50mΩ
Option, Automatic Charge Current Reduction Maintains 3.6V Minimum
V
, 4mm × 3mm DFN14 Package
OUT
LTC4089/LTC4089-5 USB Power Manager with Ideal Diode Controller
and High Efficiency Li-Ion Battery Charger
High Efficiency 1.2A Charger from 6V to 36V (40V Max) Input. Charges
Single Cell Li-Ion/Polymer Batteries Directly from a USB Port, Thermal
Regulation, 200mΩ Ideal Diode with <50mΩ Option, 4mm × 3mm
DFN14 Package. Bat-Track Adaptive Output Control (LTC4089), Fixed 5V
Output (LTC4089-5)
4088fb
LT 0512 REV B • PRINTED IN USA
LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
24
●
●
LINEAR TECHNOLOGY CORPORATION 2007
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
相关型号:
LTC4088EDE-1
IC 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14, 4 X 3 MM, 0.75 MM HEIGHT, PLASTIC, MO-229WGED-3, DFN-14, Power Management Circuit
Linear
LTC4088EDE-1#PBF
LTC4088-1/-2 - High Efficiency Battery Charger/USB Power Manager with Regulated Output Voltage; Package: DFN; Pins: 14; Temperature Range: -40°C to 85°C
Linear
LTC4088EDE-1#TR
IC 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14, 4 X 3 MM, 0.75 MM HEIGHT, PLASTIC, MO-229WGED-3, DFN-14, Power Management Circuit
Linear
LTC4088EDE-1#TRPBF
LTC4088-1/-2 - High Efficiency Battery Charger/USB Power Manager with Regulated Output Voltage; Package: DFN; Pins: 14; Temperature Range: -40°C to 85°C
Linear
LTC4088EDE-1-PBF
High Effi ciency Battery Charger/USB Power Manager with Regulated Output Voltage
Linear
LTC4088EDE-1-TRPBF
High Effi ciency Battery Charger/USB Power Manager with Regulated Output Voltage
Linear
LTC4088EDE-2#PBF
LTC4088-1/-2 - High Efficiency Battery Charger/USB Power Manager with Regulated Output Voltage; Package: DFN; Pins: 14; Temperature Range: -40°C to 85°C
Linear
LTC4088EDE-2#TRPBF
LTC4088-1/-2 - High Efficiency Battery Charger/USB Power Manager with Regulated Output Voltage; Package: DFN; Pins: 14; Temperature Range: -40°C to 85°C
Linear
LTC4088EDE-2-PBF
High Effi ciency Battery Charger/USB Power Manager with Regulated Output Voltage
Linear
LTC4088EDE-2-TRPBF
High Effi ciency Battery Charger/USB Power Manager with Regulated Output Voltage
Linear
©2020 ICPDF网 联系我们和版权申明