LTC3890EUH [Linear]
60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller; 60V低IQ ,双通道,两相同步降压型DC / DC控制器型号: | LTC3890EUH |
厂家: | Linear |
描述: | 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller |
文件: | 总36页 (文件大小:435K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LTC3890
60V Low I ,
Q
Dual, 2-Phase Synchronous
Step-Down DC/DC Controller
DESCRIPTION
FEATURES
The LTC®3890 is a high performance dual step-down
switching regulator DC/DC controller that drives all N-
channel synchronous power MOSFET stages. A constant
frequency current mode architecture allows a phase-lock-
able frequency of up to 850kHz. Power loss and noise due
totheESRoftheinputcapacitorareminimizedbyoperating
the two controller output stages out-of-phase.
n
Wide V Range: 4V to 60V (65V Abs Max)
IN
n
n
n
n
Low Operating I : 50μA (One Channel On)
Q
Wide Output Voltage Range: 0.8V ≤ V
≤ 24V
OUT
R
or DCR Current Sensing
SENSE
Out-of-Phase Controllers Reduce Required Input
Capacitance and Power Supply Induced Noise
Phase-Lockable Frequency (75kHz to 850kHz)
Programmable Fixed Frequency (50kHz to 900kHz)
Selectable Continuous, Pulse Skipping or Low Ripple
Burst Mode® Operation at Light Loads
n
n
n
The50ꢀAno-loadquiescentcurrentextendsoperatingrun
timeinbattery-poweredsystems.OPTI-LOOP® compensa-
tion allows the transient response to be optimized over
a wide range of output capacitance and ESR values. The
LTC3890 features a precision 0.8V reference and power
good output indicators. A wide 4V to 60V input supply
range encompasses a wide range of intermediate bus
voltages and battery chemistries.
n
n
n
n
n
n
n
n
n
Selectable Current Limit
Very Low Dropout Operation: 99% Duty Cycle
Adjustable Output Voltage Soft-Start or Tracking
Power Good Output Voltage Monitors
Output Overvoltage Protection
Low Shutdown I : < 14μA
Internal LDO Powers Gate Drive from V or EXTV
No Current Foldback During Start-up
Q
Independent TRACK/SS pins for each controller ramp the
IN
CC
output voltages during start-up. Current foldback limits
MOSFET heat dissipation during short-circuit conditions.
ThePLLIN/MODEpinselectsamongBurstModeoperation,
pulse skipping mode, or continuous conduction mode at
light loads. For a leaded package version (28-lead Narrow
SSOP), see the LTC3890-1 data sheet.
Small Low Profile (0.75mm) 5mm × 5mm QFN Package
APPLICATIONS
n
Automotive Always-On Systems
L, LT, LTC, LTM, Burst Mode and OPTI-LOOP are registered trademarks of Linear Technology
Corporation. All other trademarks are the property of their respective owners. Protected by U.S.
Patents, including 5481178, 5705919, 5929620, 6100678, 6144194, 6177787, 6304066, 6580258,
7230497.
n
Battery Operated Digital Devices
n
Distributed DC Power Systems
TYPICAL APPLICATION
High Efficiency Dual 8.5V/3.3V Output Step-Down Converter
Efficiency and Power Loss vs
V
IN
Output Current (Buck)
9V TO 60V
22μF
4.7μF
10000
1000
100
100
90
80
70
60
50
40
30
20
V
V
= 12V
OUT
IN
V
IN
INTV
CC
= 3.3V
TG1
TG2
0.1μF
0.1μF
BOOST1
SW1
BOOST2
SW2
4.7μH
8μH
BG1
BG2
LTC3890
PGND
10
+
+
SENSE1
SENSE1
SENSE2
0.01Ω
0.008Ω
1
–
–
V
SENSE2
OUT2
V
OUT1
3.3V
5A
10
0
8.5V
3A
V
V
ITH2
FB1
FB2
0.1
10
100k
100k
10.5k
ITH1
0.0001 0.001
0.01
0.1
1
470μF
1000pF
34.8k
1000pF
34.8k
330μF
TRACK/SS1 SGND TRACK/SS2
0.1μF
OUTPUT CURRENT (A)
31.6k
3890 TA01b
0.1μF
3890 TA01
3890f
1
LTC3890
ABSOLUTE MAXIMUM RATINGS
PIN CONFIGURATION
(Note 1)
TOP VIEW
Input Supply Voltage (V )......................... –0.3V to 65V
IN
Topside Driver Voltages
BOOST1, BOOST2 ................................ –0.3V to 71V
Switch Voltage (SW1, SW2) ........................ –5V to 65V
(BOOST1-SW1), (BOOST2-SW2) ................ –0.3V to 6V
RUN1, RUN2 ............................................... –0.3V to 8V
Maximum Current Sourced into Pin from
32 31 30 29 28 27 26 25
–
SENSE1
FREQ
1
2
3
4
5
6
7
8
24 BOOST1
23 BG1
PHASMD
CLKOUT
PLLIN/MODE
SGND
V
IN
22
21
PGND
33
SGND
Source > 8V .....................................................100μA
20 EXTV
CC
CC
+
–
+
–
SENSE1 , SENSE2 , SENSE1
INTV
19
18 BG2
17 BOOST2
SENSE2 Voltages...................................... –0.3V to 28V
RUN1
PLLIN/MODE, FREQ Voltages .............. –0.3V to INTV
RUN2
CC
CC
9
10 11 12 13 14 15 16
I
, PHASMD Voltages ....................... –0.3V to INTV
LIM
EXTV ...................................................... –0.3V to 14V
CC
ITH1, ITH2, V , V Voltages................... –0.3V to 6V
FB1 FB2
PGOOD1, PGOOD2 Voltages ....................... –0.3V to 6V
TRACK/SS1, TRACK/SS2 Voltages .............. –0.3V to 6V
Operating Junction Temperature Range
UH PACKAGE
32-LEAD (5mm × 5mm) PLASTIC QFN
T
= 125°C, θ = 34°C/W
JA
JMAX
EXPOSED PAD (PIN 33) IS SGND, MUST BE SOLDERED TO PCB
(Note 2) ................................................. –40°C to 125°C
Maximum Junction Temperature (Note 3) ............ 125°C
Storage Temperature Range................... –65°C to 150°C
ORDER INFORMATION
LEAD FREE FINISH
LTC3890EUH#PBF
LTC3890IUH#PBF
TAPE AND REEL
PART MARKING*
3890
PACKAGE DESCRIPTION
32-Lead (5mm × 5mm) Plastic QFN
32-Lead (5mm × 5mm) Plastic QFN
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
LTC3890EUH#TRPBF
LTC3890IUH#TRPBF
3890
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TJ = 25°C. VIN = 12V, VRUN1,2 = 5V, EXTVCC = 0V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
V
Input Supply Operating Voltage Range
Regulated Feedback Voltage
4
60
V
IN
(Note 4) I
Voltage = 1.2V
V
V
V
FB1,2
TH1,2
–40°C to 125°C
–40°C to 85°C
l
0.788
0.792
0.800
0.800
0.812
0.808
I
Feedback Current
(Note 4)
5
50
nA
FB1,2
V
Reference Voltage Line Regulation
(Note 4) V = 4.5V to 60V
0.002
0.02
%/V
REFLNREG
IN
3890f
2
LTC3890
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TJ = 25°C. VIN = 12V, VRUN1,2 = 5V, EXTVCC = 0V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
Output Voltage Load Regulation
(Note4)
LOADREG
l
l
Measured in Servo Loop,
0.01
0.1
%
Δ
ITH
Voltage = 1.2V to 0.7V
(Note4)
Measured in Servo Loop,
–0.01
2
–0.1
%
Δ
ITH
Voltage = 1.2V to 2V
g
m1,2
Transconductance Amplifier g
Input DC Supply Current
(Note 4) I
= 1.2V, Sink/Source = 5μA
TH1,2
mmho
m
I
(Note 5)
Q
Pulse Skip or Forced Continuous Mode RUN1 = 5V and RUN2 = 0V or
(One Channel On) RUN1 = 0V and RUN2 = 5V,
= 0.83V (No Load)
1.3
mA
V
FB1
Pulse Skip or Forced Continuous Mode RUN1,2 = 5V, V
(Both Channels On)
= 0.83V (No Load)
2
mA
μA
FB1,2
Sleep Mode (One Channel On)
RUN1 = 5V and RUN2 = 0V or
RUN1 = 0V and RUN2 = 5V,
50
75
V
= 0.83V (No Load)
FB1
Sleep Mode (Both Channels On)
Shutdown
RUN1,2 = 5V, V
RUN1,2 = 0V
= 0.83V (No Load)
60
14
100
25
μA
μA
FB1,2
l
l
UVLO
Undervoltage Lockout
INTV Ramping Up
4.0
3.8
4.2
4.0
V
V
CC
INTV Ramping Down
3.6
7
CC
V
OVL
Feedback Overvoltage Protection
Measured at V
Each Channel
, Relative to Regulated V
FB1,2 FB1,2
10
13
1
%
+
–
+
I
I
SENSE Pin Current
μA
SENSE
SENSE
–
SENSE Pins Current
Each Channel
–
–
V
SENSE
V
SENSE
< INTV – 0.5V
1
μA
μA
CC
> INTV + 0.5V
700
99
CC
DF
Maximum Duty Factor
In Dropout
= 0V
98
%
MAX
I
Soft-Start Charge Current
V
0.7
1.0
1.4
μA
TRACK/SS1,2
TRACK1,2
l
l
V
V
On
On
RUN1 Pin On Threshold
RUN2 Pin On Threshold
V
RUN1
V
RUN2
Rising
Rising
1.15
1.20
1.21
1.25
1.27
1.30
V
V
RUN1
RUN2
V
V
Hyst RUN Pin Hysteresis
50
mV
RUN1,2
l
l
l
Maximum Current Sense Threshold
V
FB1,2
V
FB1,2
V
FB1,2
= 0.7V, V
= 0.7V, V
= 0.7V, V
–, – = 3.3V, I = 0
22
43
64
30
50
75
36
57
85
mV
mV
mV
SENSE(MAX)
SENSE1
SENSE1
SENSE1
2
LIM
–, – = 3.3V, I = INTV
2
LIM
CC
–, – = 3.3V, I = FLOAT
2
LIM
Gate Driver
TG1,2
Pull-Up On-Resistance
Pull-Down On-Resistance
2.5
1.5
ꢁ
ꢁ
BG1,2
Pull-Up On-Resistance
Pull-Down On-Resistance
2.4
1.1
ꢁ
ꢁ
TG Transition Time:
Rise Time
Fall Time
(Note 6)
TG1,2 t
TG1,2 t
C
C
= 3300pF
25
16
ns
ns
r
f
LOAD
LOAD
= 3300pF
BG Transition Time:
Rise Time
Fall Time
(Note 6)
LOAD
LOAD
BG1,2 t
BG1,2 t
C
C
= 3300pF
= 3300pF
28
13
ns
ns
r
f
TG/BG t
Top Gate Off to Bottom Gate On Delay
Synchronous Switch-On Delay Time
C
= 3300pF Each Driver
30
30
95
ns
1D
LOAD
BG/TG t
Bottom Gate Off to Top Gate On Delay
Top Switch-On Delay Time
C
= 3300pF Each Driver
ns
1D
LOAD
t
Minimum On-Time
(Note 7)
ns
ON(MIN)
3890f
3
LTC3890
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TJ = 25°C. VIN = 12V, VRUN1,2 = 5V, EXTVCC = 0V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
4.85
4.85
4.5
TYP
MAX
UNITS
INTV Linear Regulator
CC
V
V
V
V
V
V
Internal V Voltage
6V < V < 60V, V = 0V
EXTVCC
5.1
0.7
5.1
0.6
4.7
250
5.35
1.1
V
%
V
INTVCCVIN
LDOVIN
CC
IN
INTV Load Regulation
I
CC
= 0mA to 50mA, V
= 0V
CC
EXTVCC
Internal V Voltage
6V < V < 13V
EXTVCC
5.35
1.1
INTVCCEXT
LDOEXT
CC
INTV Load Regulation
I
CC
= 0mA to 50mA, V
= 8.5V
%
V
CC
EXTVCC
EXTV Switchover Voltage
EXTV Ramping Positive
4.9
EXTVCC
CC
CC
EXTV Hysteresis
mV
LDOHYS
CC
Oscillator and Phase-Locked Loop
f
f
f
f
f
f
Programmable Frequency
Programmable Frequency
Programmable Frequency
Low Fixed Frequency
R
R
R
= 25k, PLLIN/MODE = DC Voltage
= 65k, PLLIN/MODE = DC Voltage
= 105k, PLLIN/MODE = DC Voltage
= 0V, PLLIN/MODE = DC Voltage
105
440
835
350
535
kHz
kHz
kHz
kHz
kHz
kHz
25kꢁ
65kꢁ
105kꢁ
LOW
FREQ
FREQ
FREQ
FREQ
FREQ
375
505
V
V
320
485
75
380
585
850
High Fixed Frequency
= INTV , PLLIN/MODE = DC Voltage
CC
HIGH
SYNC
l
Synchronizable Frequency
PLLIN/MODE = External Clock
PGOOD1 and PGOOD2 Outputs
V
PGOOD Voltage Low
PGOOD Leakage Current
PGOOD Trip Level
I
= 2mA
= 5V
0.2
0.4
1
V
PGL
PGOOD
I
V
V
μA
PGOOD
PGOOD
V
with Respect to Set Regulated Voltage
FB
PG
V
FB
Ramping Negative
–13
7
–10
2.5
–7
13
%
%
Hysteresis
V
with Respect to Set Regulated Voltage
FB
V
FB
Ramping Positive
10
2.5
%
%
Hysteresis
t
Delay for Reporting a Fault
25
μs
PG
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Ratings for extended periods may affect device reliability and
lifetime.
Note 4: The LTC3890 is tested in a feedback loop that servos V
to a
ITH1,2
specified voltage and measures the resultant V . The specification at
FB1,2
85°C is not tested in production. This specification is assured by design,
characterization and correlation to production testing at 125°C.
Note 2: The LTC3890E is guaranteed to meet performance specifications
from 0°C to 125°C. Specifications over the –40°C to 125°C operating
junction temperature range are assured by design, characterization and
correlation with statistical process controls. The LTC3890I is guaranteed
over the full –40°C to 125°C operating junction temperature range.
Note 5: Dynamic supply current is higher due to the gate charge being
delivered at the switching frequency. See Applications information.
Note 6: Rise and fall times are measured using 10% and 90% levels. Delay
times are measured using 50% levels.
Note 7: The minimum on-time condition is specified for an inductor
Note 3: T is calculated from the ambient temperature T and power
J
A
peak-to-peak ripple current ≥ 40% of I
(See Minimum On-Time
MAX
dissipation P according to the following formula:
D
Considerations in the Applications Information section).
T = T + (P • 34°C/W)
J
A
D
3890f
4
LTC3890
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency and Power Loss vs
Output Current
Efficiency vs Output Current
Efficiency vs Input Voltage
100
98
96
94
92
90
88
86
84
10000
1000
100
100
90
80
70
60
50
40
30
20
100
90
80
70
60
50
40
30
20
V
V
= 12V
IN
OUT
V
= 8.5V
BURST EFFICIENCY
OUT
= 3.3V
V
= 3.3V
OUT
V
= 8.5V
OUT2
CCM LOSS
BURST LOSS
PULSE-SKIPPING
LOSS
V
= 3.3V
10
OUT1
CCM EFFICIENCY
1
Burst Mode OPERATION
PULSE-SKIPPING
EFFICIENCY
82
80
10
0
10
0
I
= 2A
V
= 12V
LOAD
5
IN
0.1
10
0
10 15 20 25 30 35 40 45 50 55 60
0.0001 0.001
0.01
OUTPUT CURRENT (A)
FIGURE 13 CIRCUIT
0.1
1
10
0.0001 0.001
0.01
0.1
1
INPUT VOLTAGE (V)
OUTPUT CURRENT (A)
3890 G03
3890 G02
3890 G01
FIGURE 13 CIRCUIT
FIGURE 13 CIRCUIT
Load Step
Burst Mode Operation
Load Step
Pulse-Skipping Mode
Load Step
Forced Continuous Mode
V
V
V
OUT
OUT
OUT
100mV/DIV
AC-
100mV/DIV
AC-
100mV/DIV
AC-
COUPLED
COUPLED
COUPLED
I
I
I
L
L
L
2A/DIV
2A/DIV
2A/DIV
3890 G04
3890 G06
3890 G05
50μs/DIV
50μs/DIV
50μs/DIV
V
V
= 12V
V
V
= 12V
V
V
= 12V
IN
OUT
IN
OUT
IN
OUT
= 3.3V
= 3.3V
= 3.3V
FIGURE 13 CIRCUIT
FIGURE 13 CIRCUIT
FIGURE 13 CIRCUIT
Soft Start-Up
Tracking Start-Up
Inductor Current at Light Load
FORCED
CONTINUOUS
MODE
V
OUT2
V
OUT2
2V/DIV
2V/DIV
Burst Mode
OPERATION
1A/DIV
V
V
OUT1
OUT1
2V/DIV
2V/DIV
PULSE-SKIPPING
MODE
3890 G08
3890 G07
3890 G09
2ms/DIV
FIGURE 13 CIRCUIT
5μs/DIV
2ms/DIV
FIGURE 13 CIRCUIT
V
V
LOAD
= 12V
IN
= 3.3V
OUT
I
= 200μA
3890f
5
LTC3890
TYPICAL PERFORMANCE CHARACTERISTICS
Total Input Supply Current vs
Input Voltage
EXTVCC Switchover and INTVCC
Voltages vs Temperature
INTVCC Line Regulation
6.0
5.8
5.6
5.4
5.2
5.0
4.8
4.6
4.4
4.2
4.0
300
250
200
150
100
5.2
5.1
5.0
4.9
4.8
INTV
CC
300μA
EXTV RISING
CC
EXTV FALLING
CC
NO LOAD
50
0
–45
5
30
55
80 105 130
5
10 15 20 25 30 35 40 45 50 55 60 65
–20
5
10 15 20 25 30 35 40 45 50 55 60 65
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
TEMPERATURE (°C)
3890 G10
3890 G12
3890 G11
Maximum Current Sense Voltage
vs ITH Voltage
Maximum Current Sense
Threshold vs Duty Cycle
SENSE– Pin Input Bias Current
80
60
40
20
0
80
70
–100
–200
–300
–400
–500
–600
–700
–800
I
= FLOAT
LIM
PULSE SKIPPING MODE
60
50
Burst Mode
OPERATION
I
= INTV
CC
LIM
I
= GND
= INTV
LIM
0
–20
–40
40
30
20
I
LIM
CC
I
= GND
LIM
I
= FLOAT
LIM
FORCED CONTINUOUS MODE
0.8
(V)
1.2
1.4
0
0.2
0.4 0.6
V
1.0
0
10
15
20
25
5
0
10 20 30 40 50 60 70 80 90 100
V
COMMON MODE VOLTAGE (V)
SENSE
DUTY CYCLE (%)
ITH
3890 G13
3890 G14
3890 G15
Foldback Current Limit
Quiescent Current vs Temperature
INTVCC vs Load Current
80
5.20
5.15
5.10
80
70
60
50
40
30
20
10
0
V
= 12V
IN
I
= FLOAT
LIM
75
70
I
= INTV
CC
LIM
65
60
55
50
45
EXTV = 0V
CC
5.05
5.00
4.95
I
= GND
LIM
EXTV = 8.5V
CC
40
–20
5
55
80 105 130
20 40 60
120 140
–45
30
0
80 100
160
180
200
0
100 200 300 400 500 600 700 800
FEEDBACK VOLTAGE (MV)
3890 G16
TEMPERATURE (°C)
LOAD CURRENT (mA)
3890 G17
3890 G18
3890f
6
LTC3890
TYPICAL PERFORMANCE CHARACTERISTICS
Regulated Feedback Voltage
vs Temperature
TRACK/SS Pull-Up Current
vs Temperature
Shutdown (RUN) Threshold
vs Temperature
1.10
1.05
1.00
0.95
800
1.40
1.35
806
804
1.30
1.25
1.20
1.15
1.10
1.05
1.00
RUN1 RISING
RUN2 RISING
802
800
798
796
794
RUN1 FALLING
RUN2 FALLING
0.90
792
–45 –20
5
30
55
80 105 130
–20
5
55
80 105 130
–45
30
55
TEMPERATURE (°C)
105 130
–45 –20
5
30
80
TEMPERATURE (°C)
TEMPERATURE (°C)
3890 G19
3890 G21
3890 G20
SENSE– Pin Total Input Bias Current
vs Temperature
Shutdown Current vs Input
Voltage
Oscillator Frequency
vs Temperature
50
0
600
550
500
450
30
25
20
15
10
5
V
< INTV – 0.5V
CC
–50
OUT
FREQ = INTV
CC
–100
–150
–200
–250
–300
–350
–400
–450
–500
–550
–600
–650
–700
–750
–800
400
350
300
FREQ = GND
V
> INTV – 0.5V
CC
OUT
0
–45 –25 –5 15 35 55 75 95 115
55
TEMPERATURE (°C)
105 130
–45 –20
5
30
80
5
10 15 20 25 30 35 40 45 50 55 60 65
TEMPERATURE (°C)
INPUT VOLTAGE (V)
3890 G22
3890 G23
3890 G24
Undervoltage Lockout Threshold
vs Temperature
Oscillator Frequency vs Input
Voltage
Shutdown Current vs Temperature
4.4
4.3
4.2
4.1
4.0
3.9
3.8
3.7
3.6
3.5
3.4
22
20
18
356
354
352
350
348
V
= 12V
FREQ = GND
IN
RISING
16
14
12
10
8
FALLING
346
344
–45
5
30
55
80 105 130
–20
–45 –20
5
30
55
80 105 130
5
10 15 20 25 30 35 40 45 50 55 60 65
TEMPERATURE (°C)
TEMPERATURE (°C)
INPUT VOLTAGE (V)
3890 G27
3890 G26
3890 G25
3890f
7
LTC3890
PIN FUNCTIONS
–
–
SGND(Pins6, ExposedPadPin33):Small-signalground
common to both controllers, must be routed separately
from high current grounds to the common (–) terminals
SENSE1 , SENSE2 (Pin 1, Pin 9): The (–) Input to the
Differential Current Comparators. When greater than
–
INTV – 0.5V, the SENSE pin supplies current to the
CC
of the C capacitors.
current comparator.
IN
RUN1, RUN2 (Pin 7, Pin 8): Digital Run Control Inputs
for Each Controller. Forcing either of these pins below
1.2V shuts down that controller. Forcing both of these
pins below 0.7V shuts down the entire LTC3890, reducing
quiescent current to approximately 14μA.
FREQ (Pin 2): The frequency control pin for the internal
VCO. Connecting the pin to GND forces the VCO to a fixed
low frequency of 350kHz. Connecting the pin to INTV
CC
forces the VCO to a fixed high frequency of 535kHz.
Other frequencies between 50kHz and 900kHz can be
programmed using a resistor between FREQ and GND.
An internal 20μA pull-up current develops the voltage to
be used by the VCO to control the frequency.
INTV (Pin19):OutputoftheInternalLinearLowDropout
CC
Regulator. The driver and control circuits are powered
from this voltage source. Must be decoupled to power
ground with a minimum of 4.7μF ceramic or other low
PHASMD (Pin 3): Control Input to Phase Selector which
determines the phase relationships between control-
ler 1, controller 2 and the CLKOUT signal. Pulling this
pin to ground forces TG2 and CLKOUT to be out of phase
180° and 60° with respect to TG1. Connecting this pin to
ESR capacitor. Do not use the INTV pin for any other
CC
purpose.
EXTV (Pin 20): External Power Input to an Internal LDO
CC
Connected to INTV . This LDO supplies INTV power,
CC
CC
INTV forces TG2 and CLKOUT to be out of phase 240°
CC
bypassing the internal LDO powered from V whenever
IN
and 120° with respect to TG1. Floating this pin forces TG2
and CLKOUT to be out of phase 180° and 90° with respect
to TG1. Refer to Table 1.
EXTV is higher than 4.7V. See EXTV Connection in
CC
CC
the Applications Information section. Do not exceed 14V
on this pin.
CLKOUT (Pin 4): Output clock signal available to daisy-
PGND (Pin 21): Driver Power Ground. Connects to the
chain other controller ICs for additional MOSFET driver
sources of bottom (synchronous) N-channel MOSFETs
stages/phases. The output levels swing from INTV to
CC
and the (–) terminal(s) of C .
IN
ground.
V (Pin 22): Main Supply Pin. A bypass capacitor should
IN
PLLIN/MODE (Pin 5): External Synchronization Input to
PhaseDetectorandForcedContinuousModeInput. When
an external clock is applied to this pin, the phase-locked
loop will force the rising TG1 signal to be synchronized
with the rising edge of the external clock. When not syn-
chronizing to an external clock, this input, which acts on
bothcontrollers, determineshowtheLTC3890operatesat
light loads. Pulling this pin to ground selects Burst Mode
operation.Aninternal100kresistortogroundalsoinvokes
BurstModeoperationwhenthepinisfloated.Tyingthispin
be tied between this pin and the signal ground pin.
BG1, BG2 (Pin 23, Pin 18): High Current Gate Drives
for Bottom (Synchronous) N-Channel MOSFETs. Voltage
swing at these pins is from ground to INTV .
CC
BOOST1,BOOST2(Pin24,Pin17):BootstrappedSupplies
to the Topside Floating Drivers. Capacitors are connected
between the BOOST and SW pins and Schottky diodes are
tied between the BOOST and INTV pins. Voltage swing
CC
at the BOOST pins is from INTV to (V + INTV ).
CC
IN
CC
to INTV forces continuous inductor current operation.
CC
SW1, SW2 (Pin 25, Pin 16): Switch Node Connections
to Inductors.
Tying this pin to a voltage greater than 1.2V and less than
INTV – 1.3V selects pulse skipping operation.
CC
3890f
8
LTC3890
PIN FUNCTIONS
Alternatively, a resistor divider on another voltage supply
connected to this pin allows the LTC3890 output to track
the other supply during start-up.
TG1, TG2 (Pin 26, Pin 15): High Current Gate Drives for
Top N-Channel MOSFETs. These are the outputs of float-
ing drivers with a voltage swing equal to INTV – 0.5V
CC
superimposed on the switch node voltage SW.
ITH1, ITH2 (Pin 30, Pin 12): Error Amplifier Outputs and
Switching Regulator Compensation Points. Each associ-
ated channel’s current comparator trip point increases
with this control voltage.
PGOOD1, PGOOD2 (Pin 27, Pin 14): Open-Drain Logic
Output. PGOOD1,2 is pulled to ground when the voltage
on the V
pin is not within 10% of its set point.
FB1,2
V
, V (Pin31, Pin11):Receivestheremotelysensed
I
(Pin 28): Current Comparator Sense Voltage Range
FB1 FB2
LIM
feedback voltage for each controller from an external
Inputs. Tying this pin to SGND, FLOAT or INTV sets the
CC
resistive divider across the output.
maximumcurrentsensethresholdtooneofthreedifferent
levels for both comparators.
+
+
SENSE1 , SENSE2 (Pin 32, Pin 10): The (+) input to the
differential current comparators are normally connected
to DCR sensing networks or current sensing resistors.
The ITH pin voltage and controlled offsets between the
SENSE and SENSE pins in conjunction with R
the current trip threshold.
TRACK/SS1, TRACK/SS2 (Pin 29, Pin 13): External
Tracking and Soft-Start Input. The LTC3890 regulates the
V
voltage to the smaller of 0.8V or the voltage on the
FB1,2
–
+
set
TRACK/SS1,2 pin. An internal 1μA pull-up current source
is connected to this pin. A capacitor to ground at this
pin sets the ramp time to final regulated output voltage.
SENSE
3890f
9
LTC3890
FUNCTIONAL DIAGRAM
INTV
CC
V
IN
DUPLICATE FOR SECOND
CONTROLLER CHANNEL
BOOST
24, 17
D
+
B
PHASMD
3
CLKOUT
4
PGOOD1
27
0.88V
V
–
TG
26, 15
C
B
FB1
+
–
DROP
OUT
TOP
BOT
C
IN
0.72V
0.88V
DET
BOT
SW
25, 16
TOP ON
+
–
S
R
Q
PGOOD2
14
INTV
CC
Q
BG
23, 18
SWITCH
LOGIC
V
FB2
SHDN
+
–
C
OUT
0.72V
PGND
21
20μA
FREQ
2
V
OUT
VCO
CLK2
+
–
R
SENSE
0.425V
SLEEP
CLK1
L
ICMP
IR
–
+
+
–
PFD
C
LP
+
+
–
–
+
SENSE
32, 10
3mV
SYNC
DET
2.7V
0.65V
–
PLLIN/MODE
5
SENSE
1, 9
100k
SLOPE COMP
V
FB
I
LIM
28
31, 11
R
B
CURRENT
LIMIT
+
0.80V
TRACK/SS
EA
–
V
R
A
IN
22
+
–
OV
EXTV
20
CC
ITH
30, 12
C
C
0.88V
5.1V
LDO
EN
7μA (RUN1)
0.5μA (RUN2)
5.1V
LDO
EN
SHDN
RST
FB
C
C2
R
C
TRACK/SS
29, 13
FOLDBACK
1μA
2(V
)
+
–
11V
C
SHDN
SS
4.7V
RUN
7, 8
33 SGND
19 INTV
CC
3890 FD
3890f
10
LTC3890
OPERATION (Refer to the Functional Diagram)
Main Control Loop
Shutdown and Start-Up (RUN1, RUN2 and
TRACK/ SS1, TRACK/SS2 Pins)
The LTC3890 uses a constant frequency, current mode
step-down architecture with the two controller channels
operating 180 degrees out of phase. During normal op-
eration, each external top MOSFET is turned on when the
clock for that channel sets the RS latch, and is turned off
when the main current comparator, ICMP, resets the RS
latch. The peak inductor current at which ICMP trips and
resets the latch is controlled by the voltage on the ITH pin,
which is the output of the error amplifier, EA. The error
amplifier compares the output voltage feedback signal at
The two channels of the LTC3890 can be independently
shut down using the RUN1 and RUN2 pins. Pulling either
ofthesepinsbelow1.2Vshutsdownthemaincontrolloop
for that controller. Pulling both pins below 0.7V disables
both controllers and most internal circuits, including the
INTV LDOs. In this state, the LTC3890 draws only 14μA
CC
of quiescent current.
Releasing either RUN pin allows a small internal current
to pull up the pin to enable that controller. The RUN1
pin has a 7μA pull-up current while the RUN2 pin has
a smaller 0.5μA. The 7μA current on RUN1 is designed
to be large enough so that the RUN1 pin can be safely
floated (to always enable the controller) without worry of
condensation or other small board leakage pulling the pin
down. This is ideal for always-on applications where one
or both controllers are enabled continuously and never
shut down.
the V pin, (which is generated with an external resistor
FB
divider connected across the output voltage, V , to
OUT
ground)totheinternal0.800Vreferencevoltage.Whenthe
load current increases, it causes a slight decrease in V
FB
relative to the reference, which causes the EA to increase
the ITH voltage until the average inductor current matches
the new load current.
After the top MOSFET is turned off each cycle, the bottom
MOSFETisturnedonuntileithertheinductorcurrentstarts
to reverse, as indicated by the current comparator IR, or
the beginning of the next clock cycle.
The RUN pin may be externally pulled up or driven directly
by logic. When driving the RUN pin with a low impedance
source, do not exceed the absolute maximum rating of
8V. The RUN pin has an internal 11V voltage clamp that
allows the RUN pin to be connected through a resistor to a
INTV /EXTV Power
CC
CC
highervoltage(forexample,V ),solongasthemaximum
Power for the top and bottom MOSFET drivers and most
otherinternalcircuitryisderivedfromtheINTV pin.When
IN
current into the RUN pin does not exceed 100μA.
CC
the EXTV pin is left open or tied to a voltage less than
CC
The start-up of each controller’s output voltage V
is
OUT
4.7V, the V LDO (low dropout linear regulator) supplies
IN
controlled by the voltage on the TRACK/SS pin for that
channel. When the voltage on the TRACK/SS pin is less
than the 0.8V internal reference, the LTC3890 regulates
5.1V from V to INTV . If EXTV is taken above 4.7V,
IN
CC
CC
the V LDO is turned off and an EXTV LDO is turned on.
IN
CC
Onceenabled,theEXTV LDOsupplies5.1VfromEXTV
CC
CC
the V voltage to the TRACK/SS pin voltage instead of the
FB
to INTV . Using the EXTV pin allows the INTV power
CC
CC
CC
0.8V reference. This allows the TRACK/SS pin to be used
toprogramasoft-startbyconnectinganexternalcapacitor
from the TRACK/SS pin to SGND. An internal 1μA pull-up
current charges this capacitor creating a voltage ramp on
the TRACK/SS pin. As the TRACK/SS voltage rises linearly
from 0V to 0.8V (and beyond up to 5V), the output voltage
to be derived from a high efficiency external source such
as one of the LTC3890 switching regulator outputs.
Each top MOSFET driver is biased from the floating boot-
strap capacitor, C , which normally recharges during each
B
cycle through an external diode when the top MOSFET
V
OUT
rises smoothly from zero to its final value.
turns off. If the input voltage, V , decreases to a voltage
IN
close to V , the loop may enter dropout and attempt
Alternatively the TRACK/SS pin can be used to cause the
start-up of V to track that of another supply. Typically,
OUT
to turn on the top MOSFET continuously. The dropout
detector detects this and forces the top MOSFET off for
about one twelfth of the clock period every tenth cycle to
OUT
this requires connecting to the TRACK/SS pin an external
resistor divider from the other supply to ground (see Ap-
plications Information section).
allow C to recharge.
B
3890f
11
LTC3890
OPERATION (Refer to the Functional Diagram)
Light Load Current Operation (Burst Mode Operation,
Pulse Skipping or Forced Continuous Mode)
(PLLIN/MODE Pin)
In forced continuous operation or clocked by an external
clock source to use the phase-locked loop (see Frequency
Selection and Phase-Locked Loop section), the induc-
tor current is allowed to reverse at light loads or under
large transient conditions. The peak inductor current is
determined by the voltage on the ITH pin, just as in normal
operation.Inthismode,theefficiencyatlightloadsislower
thaninBurstModeoperation.However,continuousopera-
tion has the advantage of lower output voltage ripple and
less interference to audio circuitry. In forced continuous
mode, the output ripple is independent of load current.
The LTC3890 can be enabled to enter high efficiency
Burst Mode operation, constant frequency pulse skipping
mode, or forced continuous conduction mode at low load
currents. To select Burst Mode operation, tie the PLLIN/
MODE pin to a DC voltage below 0.8V (e.g., SGND). To
select forced continuous operation, tie the PLLIN/MODE
pin to INTV . To select pulse skipping mode, tie the
CC
PLLIN/MODE pin to a DC voltage greater than 1.2V and
less than INTV – 1.3V.
When the PLLIN/MODE pin is connected for pulse skip-
ping mode, the LTC3890 operates in PWM pulse skipping
mode at light loads. In this mode, constant frequency
operation is maintained down to approximately 1% of
designedmaximumoutputcurrent. Atverylightloads, the
current comparator, ICMP, may remain tripped for several
cycles and force the external top MOSFET to stay off for
the same number of cycles (i.e., skipping pulses). The
inductor current is not allowed to reverse (discontinuous
operation). This mode, like forced continuous operation,
exhibits low output ripple as well as low audio noise and
reduced RF interference as compared to Burst Mode
operation. It provides higher low current efficiency than
forced continuous mode, but not nearly as high as Burst
Mode operation.
CC
WhenacontrollerisenabledforBurstModeoperation, the
minimum peak current in the inductor is set to approxi-
mately 25% of the maximum sense voltage even though
the voltage on the ITH pin indicates a lower value. If the
average inductor current is higher than the load current,
the error amplifier, EA, will decrease the voltage on the
ITH pin. When the ITH voltage drops below 0.425V, the
internal sleep signal goes high (enabling sleep mode)
and both external MOSFETs are turned off. The ITH pin is
then disconnected from the output of the EA and parked
at 0.450V.
In sleep mode, much of the internal circuitry is turned off,
reducing the quiescent current that the LTC3890 draws.
If one channel is shut down and the other channel is in
sleep mode, the LTC3890 draws only 50μA of quiescent Frequency Selection and Phase-Locked Loop
current. If both channels are in sleep mode, the LTC3890 (FREQ and PLLIN/MODE Pins)
draws only 60μA of quiescent current. In sleep mode,
Theselectionofswitchingfrequencyisatrade-offbetween
the load current is supplied by the output capacitor. As
efficiency and component size. Low frequency opera-
the output voltage decreases, the EA’s output begins to
tion increases efficiency by reducing MOSFET switching
rise. When the output voltage drops enough, the ITH pin
losses, but requires larger inductance and/or capacitance
is reconnected to the output of the EA, the sleep signal
to maintain low output ripple voltage.
goes low, and the controller resumes normal operation
The switching frequency of the LTC3890’s controllers can
be selected using the FREQ pin.
by turning on the top external MOSFET on the next cycle
of the internal oscillator.
If the PLLIN/MODE pin is not being driven by an external
clock source, the FREQ pin can be tied to SGND, tied to
WhenacontrollerisenabledforBurstModeoperation, the
inductorcurrentisnotallowedtoreverse. Thereversecur-
rentcomparator,IR,turnsoffthebottomexternalMOSFET
just before the inductor current reaches zero, preventing
it from reversing and going negative. Thus, the controller
operates in discontinuous operation.
INTV orprogrammedthroughanexternalresistor. Tying
CC
FREQ to SGND selects 350kHz while tying FREQ to INTV
CC
selects535kHz.PlacingaresistorbetweenFREQandSGND
allows the frequency to be programmed between 50kHz
and 900kHz, as shown in Figure 10.
3890f
12
LTC3890
OPERATION (Refer to the Functional Diagram)
A phase-locked loop (PLL) is available on the LTC3890
to synchronize the internal oscillator to an external clock
source that is connected to the PLLIN/MODE pin. The
LTC3890’s phase detector adjusts the voltage (through an
internallowpassfilter)oftheVCOinputtoaligntheturn-on
of controller 1’s external top MOSFET to the rising edge of
thesynchronizingsignal.Thus,theturn-onofcontroller 2’s
external top MOSFET is 180 degrees out of phase to the
rising edge of the external clock source.
Output Overvoltage Protection
An overvoltage comparator guards against transient over-
shoots as well as other more serious conditions that may
overvoltage the output. When the V pin rises by more
than 10% above its regulation point of 0.800V, the top
MOSFET is turned off and the bottom MOSFET is turned
on until the overvoltage condition is cleared.
FB
Power Good (PGOOD1 and PGOOD2) Pins
The VCO input voltage is prebiased to the operating fre-
quency set by the FREQ pin before the external clock is
applied. If prebiased near the external clock frequency,
the PLL loop only needs to make slight changes to the
VCO input in order to synchronize the rising edge of the
external clock’s to the rising edge of TG1. The ability to
prebias the loop filter allows the PLL to lock-in rapidly
without deviating far from the desired frequency.
Each PGOOD pin is connected to an open drain of an
internal N-channel MOSFET. The MOSFET turns on and
pulls the PGOOD pin low when the corresponding V pin
FB
voltage is not within 10% of the 0.8V reference voltage.
ThePGOODpinisalsopulledlowwhenthecorresponding
RUN pin is low (shut down). When the V pin voltage
FB
is within the 10% requirement, the MOSFET is turned
off and the pin is allowed to be pulled up by an external
resistor to a source no greater than 6V.
The typical capture range of the phase-locked loop is from
approximately 55kHz to 1MHz, with a guarantee to be
between75kHzand850kHz.Inotherwords,theLTC3890’s
PLLisguaranteedtolocktoanexternalclocksourcewhose
frequency is between 75kHz and 850kHz.
Foldback Current
When the output voltage falls to less than 70% of its
nominal level, foldback current limiting is activated, pro-
gressively lowering the peak current limit in proportion to
the severity of the overcurrent or short-circuit condition.
Foldback current limiting is disabled during the soft-start
The typical input clock thresholds on the PLLIN/MODE
pin are 1.6V (rising) and 1.2V (falling).
PolyPhase Applications (CLKOUT and PHASMD Pins)
interval (as long as the V voltage is keeping up with the
FB
The LTC3890 features two pins (CLKOUT and PHASMD)
that allow other controller ICs to be daisy-chained with
the LTC3890 in PolyPhase applications. The clock output
signal on the CLKOUT pin can be used to synchronize
additional power stages in a multiphase power supply
solution feeding a single, high current output or multiple
separate outputs. The PHASMD pin is used to adjust the
phase of the CLKOUT signal as well as the relative phases
between the two internal controllers, as summarized in
Table 1. The phases are calculated relative to the zero
degrees phase being defined as the rising edge of the top
gate driver output of controller 1 (TG1).
TRACK/SS voltage).
Theory and Benefits of 2-Phase Operation
Why the need for 2-phase operation? Up until the 2-phase
family, constant-frequency dual switching regulators
operated both channels in phase (i.e., single phase
operation). This means that both switches turned on at
the same time, causing current pulses of up to twice the
amplitude of those for one regulator to be drawn from the
input capacitor and battery. These large amplitude current
pulses increased the total RMS current flowing from the
input capacitor, requiring the use of more expensive input
capacitorsandincreasingbothEMIandlossesintheinput
capacitor and battery.
Table 1
V
CONTROLLER 2 PHASE
CLKOUT PHASE
PHASMD
GND
180°
180°
240°
60°
90°
Floating
INTV
120°
CC
3890f
13
LTC3890
OPERATION (Refer to the Functional Diagram)
With 2-phase operation, the two channels of the dual
switchingregulatorareoperated180degreesoutofphase.
Thiseffectivelyinterleavesthecurrentpulsesdrawnbythe
switches,greatlyreducingtheoverlaptimewheretheyadd
together. The result is a significant reduction in total RMS
input current, which in turn allows less expensive input
capacitors to be used, reduces shielding requirements for
EMI and improves real world operating efficiency.
voltage V (Duty Cycle = V /V ). Figure 2 shows how
IN
OUT IN
theRMSinputcurrentvariesforsingle-phaseand2-phase
operation for 3.3V and 5V regulators over a wide input
voltage range.
It can readily be seen that the advantages of 2-phase op-
eration are not just limited to a narrow operating range,
for most applications is that 2-phase operation will reduce
theinputcapacitorrequirementtothatforjustonechannel
operating at maximum current and 50% duty cycle.
Figure 1 compares the input waveforms for a representa-
tive single-phase dual switching regulator to the LTC3890
2-phasedualswitchingregulator.Anactualmeasurementof
the RMS input current under these conditions shows that
3.0
SINGLE PHASE
2-phaseoperationdroppedtheinputcurrentfrom2.53A
RMS
DUAL CONTROLLER
2.5
2.0
1.5
1.0
0.5
0
to1.55A
.Whilethisisanimpressivereductioninitself,
RMS
2
rememberthatthepowerlossesareproportionaltoI
,
RMS
meaning that the actual power wasted is reduced by a fac-
tor of 2.66. The reduced input ripple voltage also means
less power is lost in the input power path, which could
include batteries, switches, trace/connector resistances
and protection circuitry. Improvements in both conducted
and radiated EMI also directly accrue as a result of the
reduced RMS input current and voltage.
2-PHASE
DUAL CONTROLLER
V
V
= 5V/3A
O1
O2
= 3.3V/3A
0
10
20
30
40
INPUT VOLTAGE (V)
3890 F02
Of course, the improvement afforded by 2-phase opera-
tion is a function of the dual switching regulator’s relative
duty cycles which, in turn, are dependent upon the input
Figure 2. RMS Input Current Comparison
5V SWITCH
20V/DIV
3.3V SWITCH
20V/DIV
INPUT CURRENT
5A/DIV
INPUT VOLTAGE
500mV/DIV
3890 F01
I
= 2.53A
I
= 1.55A
IN(MEAS) RMS
IN(MEAS)
RMS
Figure 1. Input Waveforms Comparing Single-Phase (a) and 2-Phase (b) Operation for Dual Switching Regulators
Converting 12V to 5V and 3.3V at 3A Each. The Reduced Input Ripple with the 2-Phase Regulator Allows
Less Expensive Input Capacitors, Reduces Shielding Requirements for EMI and Improves Efficiency
3890f
14
LTC3890
APPLICATIONS INFORMATION
TheTypicalApplicationonthefirstpageisabasicLTC3890
application circuit. LTC3890 can be configured to use
either DCR (inductor resistance) sensing or low value
resistor sensing. The choice between the two current
sensing schemes is largely a design trade-off between
cost, power consumption and accuracy. DCR sensing
is becoming popular because it saves expensive current
sensing resistors and is more power efficient, especially
in high current applications. However, current sensing
resistors provide the most accurate current limits for the
controller. Other external component selection is driven
by the load requirement, and begins with the selection of
Filter components mutual to the sense lines should be
placed close to the LTC3890, and the sense lines should
run close together to a Kelvin connection underneath the
current sense element (shown in Figure 3). Sensing cur-
rent elsewhere can effectively add parasitic inductance
and capacitance to the current sense element, degrading
the information at the sense terminals and making the
programmed current limit unpredictable. If inductor DCR
sensing is used (Figure 4b), sense resistor R1 should be
TO SENSE FILTER,
NEXT TO THE CONTROLLER
C
OUT
R
(if R
is used) and inductor value. Next, the
SENSE
SENSE
3890 F03
powerMOSFETsandSchottkydiodesareselected. Finally,
input and output capacitors are selected.
INDUCTOR OR R
SENSE
Figure 3. Sense Lines Placement with Inductor or Sense Resistor
Current Limit Programming
V
V
IN
IN
INTV
CC
The ILIM pin is a tri-level logic input which sets the maxi-
mumcurrentlimitofthecontroller.WhenILIM isgrounded,
the maximum current limit threshold voltage of the cur-
rent comparator is programmed to be 30mV. When ILIM
is floated, the maximum current limit threshold is 75mV.
When ILIM is tied to INTVCC, the maximum current limit
threshold is set to 50mV.
BOOST
TG
R
SENSE
SW
V
OUT
LTC3890
BG
+
SENSE
PLACE CAPACITOR NEAR
SENSE PINS
–
+
–
SENSE
SGND
SENSE and SENSE Pins
+
–
3890 F04a
The SENSE and SENSE pins are the inputs to the cur-
rent comparators. The common mode voltage range on
these pins is 0V to 28V (abs max), enabling the LTC3857
to regulate output voltages up to a nominal 24V (allowing
margin for tolerances and transients).
(4a) Using a Resistor to Sense Current
V
V
IN
IN
INTV
CC
+
INDUCTOR
DCR
BOOST
TG
The SENSE pin is high impedance over the full common
mode range, drawing at most 1μA. This high impedance
allows the current comparators to be used in inductor
DCR sensing.
L
SW
V
OUT
LTC3890
BG
–
R1
C1* R2
The impedance of the SENSE pin changes depending on
+
SENSE
–
the common mode voltage. When SENSE is less than
–
SENSE
INTV – 0.5V, a small current of less than 1μA flows out
CC
–
SGND
of the pin. When SENSE is above INTV + 0.5V, a higher
CC
3890 F04b
R2
R1 + R2
L
||
(R1 R2) • C1 =
*PLACE C1 NEAR
SENSE PINS
R
= DCR
SENSE(EQ)
current(~700μA)flowsintothepin.BetweenINTV –0.5V
CC
DCR
andINTV +0.5V, thecurrenttransitionsfromthesmaller
CC
(4b) Using the Inductor DCR to Sense Current
Figure 4. Current Sensing Methods
current to the higher current.
3890f
15
LTC3890
APPLICATIONS INFORMATION
placed close to the switching node, to prevent noise from
coupling into sensitive small-signal nodes.
power loss through a sense resistor would cost several
points of efficiency compared to inductor DCR sensing.
If the external (R1||R2) • C1 time constant is chosen to be
exactly equal to the L/DCR time constant, the voltage drop
across the external capacitor is equal to the drop across
theinductorDCRmultipliedbyR2/(R1+R2).R2scalesthe
voltage across the sense terminals for applications where
the DCR is greater than the target sense resistor value.
To properly dimension the external filter components, the
DCR of the inductor must be known. It can be measured
using a good RLC meter, but the DCR tolerance is not
always the same and varies with temperature; consult the
manufacturers’ data sheets for detailed information.
Low Value Resistor Current Sensing
A typical sensing circuit using a discrete resistor is shown
in Figure 4a. R
output current.
is chosen based on the required
SENSE
The current comparator has a maximum threshold
determined by the I setting. The current
V
SENSE(MAX)
LIM
comparator threshold voltage sets the peak of the induc-
tor current, yielding a maximum average output current,
I
, equal to the peak value less half the peak-to-peak
MAX
ripple current, ΔI . To calculate the sense resistor value,
L
use the equation:
Using the inductor ripple current value from the Inductor
Value Calculation section, the target sense resistor value
is:
VSENSE(MAX)
RSENSE
=
ΔIL
2
IMAX
+
VSENSE(MAX)
RSENSE(EQUIV)
=
ΔIL
To ensure that the application will deliver full load current
over the full operating temperature range, choose the
minimumvaluefortheMaximumCurrentSenseThreshold
)intheElectricalCharacteristicstable(30mV,
50mV or 75mV, depending on the state of the I pin).
IMAX
+
2
To ensure that the application will deliver full load current
over the full operating temperature range, choose the
minimumvaluefortheMaximumCurrentSenseThreshold
(V
SENSE(MAX)
LIM
(V
)intheElectricalCharacteristicstable(30mV,
SENSE(MAX)
When using the controller in very low dropout conditions,
the maximum output current level will be reduced due
to the internal compensation required to meet stability
criterion for buck regulators operating at greater than
50% duty factor. A curve is provided in the Typical Perfor-
mance Characteristics section to estimate this reduction
in peak inductor current depending upon the operating
duty factor.
50mV or 75mV, depending on the state of the I pin).
LIM
Next, determine the DCR of the inductor. When provided,
use the manufacturer’s maximum value, usually given at
20°C. Increase this value to account for the temperature
coefficient of copper resistance, which is approximately
0.4%/°C. A conservative value for T
is 100°C.
L(MAX)
To scale the maximum inductor DCR to the desired sense
resistor value (R ), use the divider ratio:
D
Inductor DCR Sensing
RSENSE(EQUIV)
For applications requiring the highest possible efficiency
at high load currents, the LTC3890 is capable of sensing
the voltage drop across the inductor DCR, as shown in
Figure 4b. The DCR of the inductor represents the small
amount of DC resistance of the copper wire, which can be
lessthan1mꢁfortoday’slowvalue,highcurrentinductors.
In a high current application requiring such an inductor,
RD =
DCRMAX atT
L(MAX)
C1 is usually selected to be in the range of 0.1μF to 0.47μF.
ThisforcesR1||R2toaround2k, reducingerrorthatmight
have been caused by the SENSE pin’s 1μA current.
+
3890f
16
LTC3890
APPLICATIONS INFORMATION
The equivalent resistance R1|| R2 is scaled to the room
temperature inductance and maximum DCR:
Accepting larger values of ΔI allows the use of low
L
inductances, but results in higher output voltage ripple
and greater core losses. A reasonable starting point for
L
setting ripple current is ΔI = 0.3(I
). The maximum
MAX
R1||R2 =
L
DCR at 20°C •C1
(
)
ΔI occurs at the maximum input voltage.
L
The inductor value also has secondary effects. The tran-
sition to Burst Mode operation begins when the average
inductor current required results in a peak current below
The sense resistor values are:
R1•RD
1–RD
R1||R2
RD
R1=
; R2 =
25% of the current limit determined by R
. Lower
SENSE
inductor values (higher ΔI ) will cause this to occur at
L
The maximum power loss in R1 is related to duty cycle,
and will occur in continuous mode at the maximum input
voltage:
lower load currents, which can cause a dip in efficiency in
the upper range of low current operation. In Burst Mode
operation, lower inductance values will cause the burst
frequency to decrease.
V
IN(MAX) – VOUT • V
(
R1=
)
OUT
P
LOSS
Inductor Core Selection
R1
Once the value for L is known, the type of inductor must
be selected. High efficiency converters generally cannot
affordthecorelossfoundinlowcostpowderedironcores,
forcingtheuseofmoreexpensiveferriteormolypermalloy
cores. Actual core loss is independent of core size for a
fixedinductorvalue,butitisverydependentoninductance
value selected. As inductance increases, core losses go
down. Unfortunately, increased inductance requires more
turns of wire and therefore copper losses will increase.
Ensure that R1 has a power rating higher than this value.
If high efficiency is necessary at light loads, consider this
power loss when deciding whether to use DCR sensing or
sense resistors. Light load power loss can be modestly
higher with a DCR network than with a sense resistor, due
totheextraswitchinglossesincurredthroughR1.However,
DCR sensing eliminates a sense resistor, reduces conduc-
tion losses and provides higher efficiency at heavy loads.
Peak efficiency is about the same with either method.
Ferrite designs have very low core loss and are preferred
for high switching frequencies, so design goals can
concentrate on copper loss and preventing saturation.
Ferrite core material saturates hard, which means that
inductancecollapsesabruptlywhenthepeakdesigncurrent
is exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
Inductor Value Calculation
The operating frequency and inductor selection are inter-
relatedinthathigheroperatingfrequenciesallowtheuseof
smallerinductorandcapacitorvalues.Sowhywouldanyone
ever choose to operate at lower frequencies with larger
components? The answer is efficiency. A higher frequency
generally results in lower efficiency because of MOSFET
switching and gate charge losses. In addition to this basic
trade-off, the effect of inductor value on ripple current and
low current operation must also be considered.
Power MOSFET and Schottky Diode
(Optional) Selection
Two external power MOSFETs must be selected for each
controller in the LTC3890: one N-channel MOSFET for the
top (main) switch, and one N-channel MOSFET for the
bottom (synchronous) switch.
The inductor value has a direct effect on ripple current. The
inductor ripple current, ΔI , decreases with higher induc-
L
tance or higher frequency and increases with higher V :
IN
ꢁ
ꢄ
V
V
IN
1
OUT ꢆ
1–
OUT ꢃ
ꢀIL =
V
f L
( )( )
ꢂ
ꢅ
3890f
17
LTC3890
APPLICATIONS INFORMATION
The peak-to-peak drive levels are set by the INTV
where δ is the temperature dependency of R
DR
and
CC
DS(ON)
voltage. This voltage is typically 5.1V during start-up
R
(approximately 2ꢁ) is the effective driver resistance
(see EXTV Pin Connection). Consequently, logic-level
at the MOSFET’s Miller threshold voltage. V
is the
CC
THMIN
threshold MOSFETs must be used in most applications.
typical MOSFET minimum threshold voltage.
Pay close attention to the BV
MOSFETs as well.
specification for the
DSS
2
BothMOSFETshaveI RlosseswhilethetopsideN-channel
equation includes an additional term for transition losses,
Selection criteria for the power MOSFETs include the
on-resistance, R , Miller capacitance, C , input
which are highest at high input voltages. For V < 20V
IN
the high current efficiency generally improves with larger
DS(ON)
MILLER
voltage and maximum output current. Miller capacitance,
MOSFETs, while for V > 20V the transition losses rapidly
IN
C
, can be approximated from the gate charge curve
increasetothepointthattheuseofahigherR
device
MILLER
DS(ON)
usually provided on the MOSFET manufacturers’ data
withlowerC
actuallyprovideshigherefficiency.The
MILLER
sheet. C
is equal to the increase in gate charge
synchronous MOSFET losses are greatest at high input
voltage when the top switch duty factor is low or during
a short-circuit when the synchronous switch is on close
to 100% of the period.
MILLER
along the horizontal axis while the curve is approximately
flat divided by the specified change in V . This result is
DS
then multiplied by the ratio of the application applied V
DS
to the gate charge curve specified V . When the IC is
DS
The term (1+ δ) is generally given for a MOSFET in the
operating in continuous mode the duty cycles for the top
form of a normalized R
vs Temperature curve, but
DS(ON)
and bottom MOSFETs are given by:
δ = 0.005/°C can be used as an approximation for low
VOUT
voltage MOSFETs.
Main Switch Duty Cycle =
V
The optional Schottky diodes D3 and D4 shown in
Figure 11 conduct during the dead-time between the
conduction of the two power MOSFETs. This prevents
the body diode of the bottom MOSFET from turning on,
storing charge during the dead-time and requiring a
reverse recovery period that could cost as much as 3%
IN
V − VOUT
IN
Synchronous Switch Duty Cycle =
V
IN
The MOSFET power dissipations at maximum output
current are given by:
in efficiency at high V . A 1A to 3A Schottky is generally
IN
VOUT
2
a good compromise for both regions of operation due
to the relatively small average current. Larger diodes
result in additional transition losses due to their larger
junction capacitance.
PMAIN
=
I
1+ ꢀ R
+
DS(ON)
(
MAX) (
)
V
IN
2 ꢁ
ꢃ
ꢂ
ꢄ
ꢆ
ꢅ
IMAX
2
V
R
C
•
(
)
(
DR)(
)
IN
MILLER
ꢇ
ꢉ
ꢈ
ꢊ
C and C
Selection
IN
OUT
1
1
+
f
ꢌ
( )
V
INTVCC – VTHMIN VTHMIN
The selection of C is simplified by the 2-phase architec-
ꢋ
IN
ture and its impact on the worst-case RMS current drawn
throughtheinputnetwork(battery/fuse/capacitor).Itcanbe
shown that the worst-case capacitor RMS current occurs
when only one controller is operating. The controller with
V – VOUT
2
IN
PSYNC
=
I
(
1+ ꢀ R
MAX) (
)
DS(ON)
V
IN
the highest (V )(I ) product needs to be used in the
formula shown in Equation 1 to determine the maximum
OUT OUT
3890f
18
LTC3890
APPLICATIONS INFORMATION
RMS capacitor current requirement. Increasing the out-
put current drawn from the other controller will actually
decrease the input RMS ripple current from its maximum
value. The out-of-phase technique typically reduces the
input capacitor’s RMS ripple current by a factor of 30%
to 70% when compared to a single phase power supply
solution.
The drains of the top MOSFETs should be placed within
1cmofeachotherandshareacommonC (s). Separating
IN
the drains and C may produce undesirable voltage and
IN
current resonances at V .
IN
A small (0.1μF to 1μF) bypass capacitor between the chip
V pin and ground, placed close to the LTC3890, is also
IN
suggested. A 10ꢁ resistor placed between C (C1) and
IN
Incontinuousmode,thesourcecurrentofthetopMOSFET
is a square wave of duty cycle (V )/(V ). To prevent
the V pin provides further isolation between the two
IN
channels.
OUT
IN
large voltage transients, a low ESR capacitor sized for the
maximum RMS current of one channel must be used. The
maximum RMS capacitor current is given by:
The selection of C
is driven by the effective series
OUT
resistance (ESR). Typically, once the ESR requirement
is satisfied, the capacitance is adequate for filtering. The
1/2
⎦
output ripple (ΔV ) is approximated by:
IMAX
OUT
⎡
⎤
CIN Required IRMS
≈
V
V – V
IN OUT
(1)
(
OUT )(
)
⎣
V
ꢂ
ꢅ
ꢇ
ꢆ
IN
1
ꢀVOUT ꢁ ꢀI ESR+
L ꢄ
8 • f • COUT
This formula has a maximum at V = 2V , where I
ꢃ
IN
OUT
RMS
= I /2. This simple worst-case condition is commonly
OUT
where f is the operating frequency, C
is the output
OUT
usedfordesignbecauseevensignificantdeviationsdonot
offermuchrelief.Notethatcapacitormanufacturers’ripple
current ratings are often based on only 2000 hours of life.
This makes it advisable to further derate the capacitor, or
to choose a capacitor rated at a higher temperature than
required. Several capacitors may be paralleled to meet
size or height requirements in the design. Due to the high
operating frequency of the LTC3890, ceramic capacitors
capacitance and ΔI is the ripple current in the inductor.
L
The output ripple is highest at maximum input voltage
since ΔI increases with input voltage.
L
Setting Output Voltage
The LTC3890 output voltages are each set by an external
feedback resistor divider carefully placed across the out-
put, as shown in Figure 5. The regulated output voltage
is determined by:
can also be used for C . Always consult the manufacturer
IN
if there is any question.
ꢀ
ꢃ
The benefit of the LTC3890 2-phase operation can be cal-
culatedbyusingEquation1forthehigherpowercontroller
and then calculating the loss that would have resulted if
both controller channels switched on at the same time.
The total RMS power lost is lower when both controllers
are operating due to the reduced overlap of current pulses
required through the input capacitor’s ESR. This is why
the input capacitor’s requirement calculated above for the
worst-case controller is adequate for the dual controller
design. Also, the input protection fuse resistance, battery
resistance, and PC board trace resistance losses are also
reduced due to the reduced peak currents in a 2-phase
system. The overall benefit of a multiphase design will
only be fully realized when the source impedance of the
power supply/battery is included in the efficiency testing.
R
RA
VOUT = 0.8V 1+
ꢂ
B ꢅ
ꢁ
ꢄ
To improve the frequency response, a feedforward ca-
pacitor, C , may be used. Great care should be taken to
FF
route the V line away from noise sources, such as the
FB
inductor or the SW line.
V
OUT
R
C
FF
1/2 LTC3890
V
B
A
FB
R
3890 F05
Figure 5. Setting Output Voltage
3890f
19
LTC3890
APPLICATIONS INFORMATION
Tracking and Soft-Start (TRACK/SS Pins)
V
V
X(MASTER)
OUT(SLAVE)
The start-up of each V
is controlled by the voltage on
OUT
the respective TRACK/SS pin. When the voltage on the
TRACK/SS pin is less than the internal 0.8V reference,
the LTC3890 regulates the V pin voltage to the voltage
FB
on the TRACK/SS pin instead of 0.8V. The TRACK/SS pin
can be used to program an external soft-start function or
to allow V
to track another supply during start-up.
OUT
3890 F07a
Soft-start is enabled by simply connecting a capacitor
from the TRACK/SS pin to ground, as shown in Figure 6.
An internal 1μA current source charges the capacitor,
providing a linear ramping voltage at the TRACK/SS pin.
TIME
(7a) Coincident Tracking
V
V
X(MASTER)
OUT(SLAVE)
The LTC3890 will regulate the V pin (and hence V
)
FB
OUT
according to the voltage on the TRACK/SS pin, allowing
V
to rise smoothly from 0V to its final regulated value.
OUT
The total soft-start time will be approximately:
0.8V
1μA
tSS = CSS
•
3890 F07b
1/2 LTC3890
TRACK/SS
TIME
(7b) Ratiometric Tracking
C
SS
SGND
Figure 7. Two Different Modes of Output Voltage Tracking
3890 F06
V
V
OUT
x
Figure 6. Using the TRACK/SS Pin to Program Soft-Start
1/2 LTC3890
R
B
V
Alternatively, the TRACK/SS pin can be used to track two
(or more) supplies during start-up, as shown qualita-
tively in Figures 7a and 7b. To do this, a resistor divider
FB
R
A
R
R
TRACKB
TRACKA
TRACK/SS
should be connected from the master supply (V ) to the
X
3890 F08
TRACK/SS pin of the slave supply (V ), as shown in
OUT
Figure 8. During start-up V
will track V according
to the ratio set by the resistor divider:
OUT
X
Figure 8. Using the TRACK/SS Pin for Tracking
R
TRACKA +RTRACKB
VX
RA
=
•
INTV Regulators
CC
VOUT RTRACKA
RA +RB
= V during start-up):
TheLTC3890featurestwoseparateinternalP-channellow
dropout linear regulators (LDO) that supply power at the
INTVCC pin from either the VIN supply pin or the EXTVCC
pin depending on the connection of the EXTVCC pin.
INTVCC powersthegatedriversandmuchoftheLTC3890’s
internalcircuitry.TheVINLDOandtheEXTVCCLDOregulate
For coincident tracking (V
OUT
X
R = R
A
TRACKA
TRACKB
R = R
B
3890f
20
LTC3890
APPLICATIONS INFORMATION
INTV to 5.1V. Each of these can supply a peak current of
operation and from the V LDO when the output is out of
CC
IN
50mA and must be bypassed to ground with a minimum
of 4.7μF ceramic capacitor. No matter what type of bulk
capacitor is used, an additional 1μF ceramic capacitor
regulation (e.g., start-up, short-circuit). If more current
is required through the EXTV LDO than is specified, an
CC
external Schottky diode can be added between the EXTV
CC
placed directly adjacent to the INTV and PGND pins is
and INTV pins. In this case, do not apply more than 6V
CC
CC
highlyrecommended.Goodbypassingisneededtosupply
the high transient currents required by the MOSFET gate
drivers and to prevent interaction between the channels.
to the EXTV pin and make sure that EXTV ≤ V .
CC CC IN
Significant efficiency and thermal gains can be realized
by powering INTV from the output, since the V cur-
CC
IN
High input voltage applications in which large MOSFETs
are being driven at high frequencies may cause the
maximum junction temperature rating for the LTC3890
rent resulting from the driver and control currents will be
scaled by a factor of (Duty Cycle)/(Switcher Efficiency).
For 5V to 14V regulator outputs, this means connecting
CC OUT CC
an 8.5V supply reduces the junction temperature in the
previous example from 125°C to:
to be exceeded. The INTV current, which is dominated
the EXTV pin directly to V . Tying the EXTV pin to
CC
by the gate charge current, may be supplied by either the
V
LDO or the EXTV LDO. When the voltage on the
IN
CC
EXTV pinislessthan4.7V,theV LDOisenabled.Power
CC
IN
T = 70°C + (32mA)(8.5V)(43°C/W) = 82°C
J
dissipation for the IC in this case is highest and is equal
to V • I . The gate charge current is dependent
However, for 3.3V and other low voltage outputs, addi-
IN
INTVCC
tional circuitry is required to derive INTV power from
on operating frequency as discussed in the Efficiency
Considerations section. The junction temperature can
be estimated by using the equations given in Note 3 of
the Electrical Characteristics. For example, the LTC3890
CC
the output.
The following list summarizes the four possible connec-
tions for EXTV :
CC
INTV current is limited to less than 32mA from a 40V
CC
1. EXTV LeftOpen(orGrounded).ThiswillcauseINTV
CC
CC
supply when not using the EXTV supply at a 70°C ambi-
CC
to be powered from the internal 5.1V regulator result-
ing in an efficiency penalty of up to 10% at high input
voltages.
ent temperature:
T = 70°C + (32mA)(40V)(43°C/W) = 125°C
J
To prevent the maximum junction temperature from be-
ing exceeded, the input supply current must be checked
while operating in forced continuous mode (PLLIN/MODE
2. EXTV Connected Directly to V . This is the normal
CC
OUT
connection for a 5V to 14V regulator and provides the
highest efficiency.
= INTV ) at maximum V .
CC
IN
3. EXTV Connected to an External Supply. If an external
CC
When the voltage applied to EXTV rises above 4.7V, the
CC
supply is available in the 5V to 14V range, it may be
V LDO is turned off and the EXTV LDO is enabled. The
IN
CC
usedtopowerEXTV providingitiscompatiblewiththe
CC
EXTV LDO remains on as long as the voltage applied to
CC
MOSFET gate drive requirements. Ensure that EXTV
CC
EXTV remains above 4.5V. The EXTV LDO attempts
CC
CC
< V .
IN
to regulate the INTV voltage to 5.1V, so while EXTV
CC
CC
CC
CC
4. EXTV ConnectedtoanOutput-DerivedBoostNetwork.
CC
is less than 5.1V, the LDO is in dropout and the INTV
For 3.3V and other low voltage regulators, efficiency
voltage is approximately equal to EXTV . When EXTV
CC
gains can still be realized by connecting EXTV to an
CC
is greater than 5.1V, up to an absolute maximum of 14V,
INTV is regulated to 5.1V.
output-derivedvoltagethathasbeenboostedtogreater
CC
than 4.7V. This can be done with the capacitive charge
UsingtheEXTV LDOallowstheMOSFETdriverandcon-
CC
pump shown in Figure 9. Ensure that EXTV < V .
CC
IN
trolpowertobederivedfromoneoftheLTC3890’sswitch-
ing regulator outputs (4.7V ≤ V
≤ 14V) during normal
OUT
3890f
21
LTC3890
APPLICATIONS INFORMATION
the output voltage falls below 70% of its nominal output
level, then the maximum sense voltage is progressively
lowered from 100% to 45% of its maximum selected
value. Under short-circuit conditions with very low duty
cycles, the LTC3890 will begin cycle skipping in order to
limittheshort-circuitcurrent. Inthissituationthebottom
MOSFET will be dissipating most of the power but less
than in normal operation. The short-circuit ripple current
C
IN
BAT85
BAT85
BAT85
V
IN
MTOP
MBOT
NDS7002
TG1
1/2 LTC3890
L
R
SENSE
V
EXTV
SW
OUT
CC
is determined by the minimum on-time, t
, of the
ON(MIN)
C
D
BG1
OUT
LTC3890 (≈95ns), the input voltage and inductor value:
3890 F09
PGND
ꢁ
ꢄ
V
L
ON(MIN) ꢃ IN ꢆ
ꢀIL(SC) = t
ꢂ
ꢅ
Figure 9. Capacitive Charge Pump for EXTVCC
The resulting average short-circuit current is:
Topside MOSFET Driver Supply (C , D )
B
B
1
2
Externalbootstrapcapacitors,C ,connectedtotheBOOST
ISC = 45% •ILIM(MAX) – ΔIL(SC)
B
pinssupplythegatedrivevoltagesforthetopsideMOSFETs.
Capacitor C in the Functional Diagram is charged though
B
Fault Conditions: Overvoltage Protection (Crowbar)
external diode D from INTV when the SW pin is low.
B
CC
The overvoltage crowbar is designed to blow a system
input fuse when the output voltage of the regulator rises
muchhigherthannominallevels.Thecrowbarcauseshuge
currents to flow, that blow the fuse to protect against a
shorted top MOSFET if the short occurs while the control-
ler is operating.
When one of the topside MOSFETs is to be turned on, the
driver places the C voltage across the gate-source of the
B
desired MOSFET. This enhances the top MOSFET switch
and turns it on. The switch node voltage, SW, rises to V
IN
and the BOOST pin follows. With the topside MOSFET
on, the boost voltage is above the input supply: V
=
BOOST
B
V + V
. The value of the boost capacitor, C , needs
IN
INTVCC
A comparator monitors the output for overvoltage condi-
tions. The comparator detects faults greater than 10%
above the nominal output voltage. When this condition
is sensed, the top MOSFET is turned off and the bottom
MOSFET is turned on until the overvoltage condition is
cleared. The bottom MOSFET remains on continuously
to be 100 times that of the total input capacitance of the
topsideMOSFET(s).Thereversebreakdownoftheexternal
Schottky diode must be greater than V
.
IN(MAX)
When adjusting the gate drive level, the final arbiter is the
total input current for the regulator. If a change is made
and the input current decreases, then the efficiency has
improved. If there is no change in input current, then there
is no change in efficiency.
for as long as the overvoltage condition persists; if V
OUT
returns to a safe level, normal operation automatically
resumes.
AshortedtopMOSFETwillresultinahighcurrentcondition
which will open the system fuse. The switching regulator
will regulate properly with a leaky top MOSFET by altering
the duty cycle to accommodate the leakage.
Fault Conditions: Current Limit and Current Foldback
The LTC3890 includes current foldback to help limit
load current when the output is shorted to ground. If
3890f
22
LTC3890
APPLICATIONS INFORMATION
Phase-Locked Loop and Frequency Synchronization
1000
900
800
700
600
500
400
300
200
100
0
The LTC3890 has an internal phase-locked loop (PLL)
comprised of a phase frequency detector, a lowpass filter,
and a voltage-controlled oscillator (VCO). This allows the
turn-on of the top MOSFET of controller 1 to be locked to
the rising edge of an external clock signal applied to the
PLLIN/MODEpin.Theturn-onofcontroller2’stopMOSFET
is thus 180 degrees out of phase with the external clock.
The phase detector is an edge sensitive digital type that
provides zero degrees phase shift between the external
and internal oscillators. This type of phase detector does
not exhibit false lock to harmonics of the external clock.
15 25 35 45 55 65 75 85 95 105 115 125
FREQ PIN RESISTOR (kΩ)
3890 F10
Figure 10. Relationship Between Oscillator Frequency
and Resistor Value at the FREQ Pin
If the external clock frequency is greater than the internal
oscillator’sfrequency,f ,thencurrentissourcedcontinu-
OSC
ously from the phase detector output, pulling up the VCO
Table 2 summarizes the different states in which the FREQ
pin can be used.
input. When the external clock frequency is less than f
,
OSC
current is sunk continuously, pulling down the VCO input.
If the external and internal frequencies are the same but
exhibit a phase difference, the current sources turn on for
an amount of time corresponding to the phase difference.
The voltage at the VCO input is adjusted until the phase
and frequency of the internal and external oscillators are
identical. At the stable operating point, the phase detector
output is high impedance and the internal filter capacitor,
Table 2
FREQ PIN
PLLIN/MODE PIN
DC Voltage
FREQUENCY
350kHz
0V
INTV
DC Voltage
535kHz
CC
Resistor
DC Voltage
50kHz to 900kHz
Any of the Above
External Clock
Phase Locked to
External Clock
C , holds the voltage at the VCO input.
LP
Minimum On-Time Considerations
Minimum on-time, t , is the smallest time duration
that the LTC3890 is capable of turning on the top MOSFET.
It is determined by internal timing delays and the gate
charge required to turn on the top MOSFET. Low duty
cycle applications may approach this minimum on-time
limit and care should be taken to ensure that:
Note that the LTC3890 can only be synchronized to an
external clock whose frequency is within range of the
LTC3890’sinternalVCO,whichisnominally55kHzto1MHz.
This is guaranteed to be between 75kHz and 850kHz.
ON(MIN)
Typically, the external clock (on the PLLIN/MODE pin)
input high threshold is 1.6V, while the input low threshold
is 1.1V.
VOUT
tON(MIN)
<
RapidphaselockingcanbeachievedbyusingtheFREQpin
to set a free-running frequency near the desired synchro-
nization frequency. The VCO’s input voltage is prebiased
at a frequency corresponding to the frequency set by the
FREQ pin. Once prebiased, the PLL only needs to adjust
the frequency slightly to achieve phase lock and synchro-
nization. Although it is not required that the free-running
frequency be near external clock frequency, doing so will
prevent the operating frequency from passing through a
large range of frequencies as the PLL locks.
V
f
IN( )
If the duty cycle falls below what can be accommodated
by the minimum on-time, the controller will begin to skip
cycles. The output voltage will continue to be regulated,
but the ripple voltage and current will increase.
3890f
23
LTC3890
APPLICATIONS INFORMATION
The minimum on-time for the LTC3890 is approximately
95ns. However, as the peak sense voltage decreases the
minimum on-time gradually increases up to about 130ns.
This is of particular concern in forced continuous applica-
tions with low ripple current at light loads. If the duty cycle
drops below the minimum on-time limit in this situation,
a significant amount of cycle skipping can occur with cor-
respondingly larger current and voltage ripple.
SupplyingINTV fromanoutput-derivedsourcepower
CC
through EXTV will scale the V current required
CC
IN
for the driver and control circuits by a factor of (Duty
Cycle)/(Efficiency). Forexample, ina20Vto5Vapplica-
tion, 10mA of INTV current results in approximately
CC
2.5mA of V current. This reduces the midcurrent loss
IN
from 10% or more (if the driver was powered directly
from V ) to only a few percent.
IN
2
3. I R losses are predicted from the DC resistances of the
Efficiency Considerations
fuse (if used), MOSFET, inductor, current sense resis-
tor and input and output capacitor ESR. In continuous
mode the average output current flows through L and
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can
be expressed as:
R
, but is chopped between the topside MOSFET
SENSE
andthesynchronousMOSFET.IfthetwoMOSFETshave
approximately the same R
, then the resistance
DS(ON)
of one MOSFET can simply be summed with the resis-
2
tances of L, R
and ESR to obtain I R losses. For
DS(ON)
SENSE
%Efficiency = 100% – (L1 + L2 + L3 + ...)
example, if each R
= 30mꢁ, R = 50mꢁ, R
L SENSE
where L1, L2, etc. are the individual losses as a percent-
age of input power.
= 10mꢁ and R
= 40mꢁ (sum of both input and
ESR
output capacitance losses), then the total resistance
is 130mꢁ. This results in losses ranging from 3% to
13% as the output current increases from 1A to 5A for
a 5V output, or a 4% to 20% loss for a 3.3V output.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of the
losses in LTC3890 circuits: 1) IC V current, 2) INTV
IN
CC
2
Efficiency varies as the inverse square of V
for the
regulator current, 3) I R losses, 4) topside MOSFET
OUT
sameexternalcomponentsandoutputpowerlevel. The
combined effects of increasingly lower output voltages
andhighercurrentsrequiredbyhighperformancedigital
systemsisnotdoublingbutquadruplingtheimportance
of loss terms in the switching regulator system!
transition losses.
1. The V current is the DC supply current given in the
IN
ElectricalCharacteristicstable,whichexcludesMOSFET
driverandcontrolcurrents. V currenttypicallyresults
IN
in a small (<0.1%) loss.
4. Transition losses apply only to the topside MOSFET(s),
and become significant only when operating at high
2. INTV current is the sum of the MOSFET driver and
CC
control currents. The MOSFET driver current results
from switching the gate capacitance of the power
MOSFETs. Each time a MOSFET gate is switched from
low to high to low again, a packet of charge, dQ, moves
input voltages (typically 15V or greater). Transition
losses can be estimated from:
Transition Loss = (1.7) • V • 2 • I
• C
• f
IN
O(MAX)
RSS
from INTV to ground. The resulting dQ/dt is a current
CC
Other hidden losses such as copper trace and internal
battery resistances can account for an additional 5%
to 10% efficiency degradation in portable systems. It
is very important to include these system level losses
during the design phase. The internal battery and fuse
out of INTV that is typically much larger than the
CC
control circuit current. In continuous mode, I
GATECHG
= f(Q + Q ), where Q and Q are the gate charges of
T
B
T
B
the topside and bottom side MOSFETs.
3890f
24
LTC3890
APPLICATIONS INFORMATION
resistancelossescanbeminimizedbymakingsurethat
IN
transient response once the final PC layout is done and
the particular output capacitor type and value have been
determined. The output capacitors need to be selected
because the various types and values determine the loop
gain and phase. An output current pulse of 20% to 80%
of full-load current having a rise time of 1μs to 10μs will
produce output voltage and ITH pin waveforms that will
give a sense of the overall loop stability without breaking
the feedback loop.
C has adequate charge storage and very low ESR at
the switching frequency. A 25W supply will typically
require a minimum of 20μF to 40μF of capacitance
having a maximum of 20mꢁ to 50mꢁ of ESR. The
LTC38902-phasearchitecturetypicallyhalvesthisinput
capacitance requirement over competing solutions.
Other losses including Schottky conduction losses
during dead-time and inductor core losses generally
account for less than 2% total additional loss.
Placing a power MOSFET directly across the output
capacitor and driving the gate with an appropriate signal
generator is a practical way to produce a realistic load step
condition. The initial output voltage step resulting from
the step change in output current may not be within the
bandwidth of the feedback loop, so this signal cannot be
used to determine phase margin. This is why it is better to
look at the ITH pin signal which is in the feedback loop and
is the filtered and compensated control loop response.
Checking Transient Response
The regulator loop response can be checked by looking at
the load current transient response. Switching regulators
take several cycles to respond to a step in DC (resistive)
load current. When a load step occurs, V
shifts by
OUT
an amount equal to ΔI
(ESR), where ESR is the ef-
LOAD
fective series resistance of C . ΔI
also begins to
OUT
LOAD
charge or discharge C
generating the feedback error
OUT
The gain of the loop will be increased by increasing R
C
signal that forces the regulator to adapt to the current
and the bandwidth of the loop will be increased by de-
change and return V
this recovery time V
to its steady-state value. During
can be monitored for excessive
OUT
OUT
creasing C . If R is increased by the same factor that C
C
C
C
is decreased, the zero frequency will be kept the same,
thereby keeping the phase shift the same in the most
critical frequency range of the feedback loop. The output
voltage settling behavior is related to the stability of the
closed-loopsystemandwilldemonstratetheactualoverall
supply performance.
overshoot or ringing, which would indicate a stability
problem. OPTI-LOOP compensation allows the transient
response to be optimized over a wide range of output
capacitance and ESR values. The availability of the ITH pin
not only allows optimization of control loop behavior, but
it also provides a DC coupled and AC filtered closed-loop
response test point. The DC step, rise time and settling
at this test point truly reflects the closed-loop response.
Assuming a predominantly second order system, phase
margin and/or damping factor can be estimated using the
percentage of overshoot seen at this pin. The bandwidth
can also be estimated by examining the rise time at the
pin. The ITH external components shown in Figure 13
circuit will provide an adequate starting point for most
applications.
A second, more severe transient is caused by switching
in loads with large (>1μF) supply bypass capacitors. The
dischargedbypasscapacitorsareeffectivelyputinparallel
with C , causing a rapid drop in V . No regulator can
OUT
OUT
alter its delivery of current quickly enough to prevent this
sudden step change in output voltage if the load switch
resistance is low and it is driven quickly. If the ratio of
C
to C
is greater than 1:50, the switch rise time
LOAD
OUT
should be controlled so that the load rise time is limited
to approximately 25 • C . Thus a 10μF capacitor would
LOAD
The ITH series R -C filter sets the dominant pole-zero
C
C
require a 250μs rise time, limiting the charging current
to about 200mA.
loop compensation. The values can be modified slightly
(from 0.5 to 2 times their suggested values) to optimize
3890f
25
LTC3890
APPLICATIONS INFORMATION
Design Example
ThepowerdissipationonthetopsideMOSFETcanbeeasily
estimated. Choosing a Fairchild FDS6982S dual MOSFET
As a design example for one channel, assume V = 12V
IN
MAX
results in: R
= 0.035ꢁ/0.022ꢁ, C
= 215pF. At
DS(ON)
MILLER
(nominal), V = 22V (max), V
= 3.3V, I
= 5A,
IN
OUT
maximum input voltage with T(estimated) = 50°C:
V
= 75mV and f = 350kHz.
SENSE(MAX)
2ꢀ
5A 1+ 0.005 50°C – 25°C
)( )
ꢂ
3.3V
22V
Theinductancevalueischosenfirstbasedona30%ripple
current assumption. The highest value of ripple current
occurs at the maximum input voltage. Tie the FREQ pin
to GND, generating 350kHz operation. The minimum
inductance for 30% ripple current is:
PMAIN
=
(
)
(
ꢁ
ꢃ
2
5A
2
0.035ꢄ + 22V
) (
2.5ꢄ 215pF •
)(
(
)
(
)
ꢀ
ꢂ
1
1
+
350kHz = 331mW
ꢅ
ꢆ
(
)
ꢁ
ꢃ
ꢃ
ꢂ
ꢄ
5V – 2.3V 2.3V
ꢁ
ꢃ
VOUT
f L
( )( )
VOUT
ꢆ
ꢀIL =
1–
IN(NOM)ꢆ
V
ꢅ
A short-circuit to ground will result in a folded back cur-
rent of:
A 4.7μH inductor will produce 29% ripple current. The
peak inductor current will be the maximum DC value plus
one half the ripple current, or 5.73A. Increasing the ripple
current will also help ensure that the minimum on-time
of 95ns is not violated. The minimum on-time occurs at
ꢁ
ꢃ
ꢃ
ꢂ
ꢄ
ꢆ
ꢆ
ꢅ
95ns 22V
(
)
34mV
0.01ꢀ
1
2
ISC
=
–
= 3.18A
4.7μH
with a typical value of R
= 0.125. The resulting power dissipated in the bottom
and δ = (0.005/°C)(25°C)
DS(ON)
maximum V :
IN
MOSFET is:
VOUT
3.3V
tON(MIN)
=
=
= 429ns
2
) (
V
f
22V 350kHz
IN(MAX) ( )
(
)
P
= 3.28A 1.125 0.022Ω
(
)(
)
SYNC
The equivalent R
resistor value can be calculated by
= 250mW
SENSE
using the minimum value for the maximum current sense
threshold (64mV):
which is less than under full-load conditions.
C is chosen for an RMS current rating of at least 3A at
temperature assuming only this channel is on. C
chosen with an ESR of 0.02ꢁ for low output ripple. The
output ripple in continuous mode will be highest at the
maximum input voltage. The output voltage ripple due to
ESR is approximately:
64mV
5.73A
IN
RSENSE
≤
≈ 0.01Ω
is
OUT
Choosing 1% resistors: RA = 25k and RB = 78.7k yields
an output voltage of 3.32V.
V
= R (ΔI ) = 0.02ꢁ(1.45A) = 29mV
ESR L P-P
ORIPPLE
3890f
26
LTC3890
APPLICATIONS INFORMATION
R
PU2
TRACK/SS1
V
PULL-UP
PGOOD2
ITH1
PGOOD2
PGOOD1
TG1
R
PU1
V
PULL-UP
V
PGOOD1
FB1
L1
R
SENSE
D1
+
–
V
OUT1
SENSE1
SENSE1
FREQ
SW1
LTC3890
C
B1
M1
M2
BOOST1
BG1
PHASMD
CLKOUT
PLLIN/MODE
RUN1
R
IN
C
C
OUT1
V
IN
f
1μF
IN
+
C
CERAMIC
VIN
PGND
GND
RUN2
+
EXTV
INTV
CC
CC
C
+
IN
V
SGND
C
IN
INTVCC
–
SENSE2
OUT2
1μF
CERAMIC
+
BG2
SENSE2
M4
L2
M3
D2
BOOST2
V
FB2
C
B2
SW2
TG2
ITH2
R
SENSE
V
OUT2
TRACK/SS2
ILIM
3890 F11
Figure 11. Recommended Printed Circuit Layout Diagram
3890f
27
LTC3890
APPLICATIONS INFORMATION
SW1
L1
R
SENSE1
V
OUT1
D1
C
R
L1
OUT1
V
IN
R
IN
C
IN
SW2
L2
R
SENSE2
V
OUT2
D2
C
R
L2
OUT2
BOLD LINES INDICATE
HIGH SWITCHING
CURRENT. KEEP LINES
TO A MINIMUM LENGTH.
3890 F12
Figure 12. Branch Current Waveforms
3890f
28
LTC3890
APPLICATIONS INFORMATION
PC Board Layout Checklist
–
+
4. Are the SENSE and SENSE leads routed together with
minimumPCtracespacing?Thefiltercapacitorbetween
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the IC. These items are also illustrated graphically in the
layoutdiagramofFigure11.Figure12illustratesthecurrent
waveforms present in the various branches of the 2-phase
synchronousregulatorsoperatinginthecontinuousmode.
Check the following in your layout:
+
–
SENSE and SENSE should be as close as possible
to the IC. Ensure accurate current sensing with Kelvin
connections at the SENSE resistor.
5. Is the INTV decoupling capacitor connected close
CC
to the IC, between the INTV and the power ground
CC
pins? This capacitor carries the MOSFET drivers’ cur-
rent peaks. An additional 1μF ceramic capacitor placed
1. Are the top N-channel MOSFETs MTOP1 and MTOP2
located within 1cm of each other with a common drain
immediatelynexttotheINTV andPGNDpinscanhelp
CC
improve noise performance substantially.
connection at C ? Do not attempt to split the input
IN
6. Keep the switching nodes (SW1, SW2), top gate nodes
(TG1, TG2), andboostnodes(BOOST1, BOOST2)away
from sensitive small-signal nodes, especially from
the opposites channel’s voltage and current sensing
feedback pins. All of these nodes have very large and
fast moving signals and therefore should be kept on
the output side of the LTC3890 and occupy minimum
PC trace area.
decoupling for the two channels as it can cause a large
resonant loop.
2. Are the signal and power grounds kept separate? The
combined IC signal ground pin and the ground return
of C
must return to the combined C
(–) ter-
INTVCC
OUT
minals. The path formed by the top N-channel MOSFET,
Schottky diode and the C capacitor should have short
IN
leads and PC trace lengths. The output capacitor (–)
terminals should be connected as close as possible
to the (–) terminals of the input capacitor by placing
the capacitors next to each other and away from the
Schottky loop described above.
7.Useamodifiedstargroundtechnique:alowimpedance,
large copper area central grounding point on the same
side of the PC board as the input and output capacitors
with tie-ins for the bottom of the INTV decoupling
CC
capacitor, the bottom of the voltage feedback resistive
3. Do the LTC3890 V pins’ resistive dividers connect to
FB
divider and the SGND pin of the IC.
the (+) terminals of C ? The resistive divider must be
OUT
connected between the (+) terminal of C
and signal
OUT
ground. The feedback resistor connections should not
be along the high current input feeds from the input
capacitor(s).
3890f
29
LTC3890
APPLICATIONS INFORMATION
PC Board Layout Debugging
Reduce V from its nominal level to verify operation
IN
of the regulator in dropout. Check the operation of the
Start with one controller on at a time. It is helpful to use
a DC-50MHz current probe to monitor the current in the
inductor while testing the circuit. Monitor the output
switching node (SW pin) to synchronize the oscilloscope
totheinternaloscillatorandprobetheactualoutputvoltage
as well. Check for proper performance over the operating
voltage and current range expected in the application. The
frequencyofoperationshouldbemaintainedovertheinput
voltage range down to dropout and until the output load
drops below the low current operation threshold—typi-
cally 15% of the maximum designed current level in Burst
Mode operation.
undervoltage lockout circuit by further lowering V while
IN
monitoring the outputs to verify operation.
Investigate whether any problems exist only at higher out-
put currents or only at higher input voltages. If problems
coincide with high input voltages and low output currents,
look for capacitive coupling between the BOOST, SW, TG,
and possibly BG connections and the sensitive voltage
and current pins. The capacitor placed across the current
sensing pins needs to be placed immediately adjacent to
the pins of the IC. This capacitor helps to minimize the
effects of differential noise injection due to high frequency
capacitive coupling. If problems are encountered with
high current output loading at lower input voltages, look
Thedutycyclepercentageshouldbemaintainedfromcycle
to cycle in a well-designed, low noise PCB implementa-
tion. Variation in the duty cycle at a subharmonic rate can
suggest noise pickup at the current or voltage sensing
inputs or inadequate loop compensation. Overcompen-
sation of the loop can be used to tame a poor PC layout
if regulator bandwidth optimization is not required. Only
after each controller is checked for its individual perfor-
mance should both controllers be turned on at the same
time. A particularly difficult region of operation is when
one controller channel is nearing its current comparator
trip point when the other channel is turning on its top
MOSFET. This occurs around 50% duty cycle on either
channel due to the phasing of the internal clocks and may
cause minor duty cycle jitter.
for inductive coupling between C , Schottky and the top
IN
MOSFET components to the sensitive current and voltage
sensing traces. In addition, investigate common ground
path voltage pickup between these components and the
SGND pin of the IC.
An embarrassing problem, which can be missed in an
otherwise properly working switching regulator, results
when the current sensing leads are hooked up backwards.
The output voltage under this improper hookup will still
be maintained but the advantages of current mode control
will not be realized. Compensation of the voltage loop will
be much more sensitive to component selection. This
behavior can be investigated by temporarily shorting out
the current sensing resistor—don’t worry, the regulator
will still maintain control of the output voltage.
3890f
30
LTC3890
TYPICAL APPLICATIONS
+
–
SENSE1
SENSE1
INTV
CC
C1
1nF
R
B1
100k
100k
100k
R
PGOOD1
PGOOD2
BG1
A1
31.6k
V
FB1
C
100pF
R
ITH1A
MBOT1
R
SENSE1
8mΩ
V
3.3V
5A
OUT1
C
1000pF
ITH1
SW1
ITH1
34.8k
L1
BOOST1
ITH1
4.7μH
C
OUT1
470μF
C
LTC3890
TRACK/SS1
C
SS1
0.01μF
B1
0.1μF
TG1
MTOP1
D1
I
LIM
V
IN
PHSMD
CLKOUT
PLLIN/MODE
V
IN
9V TO 60V
C
IN
220μF
INTV
CC
C
INT
4.7μF
SGND
EXTV
PGND
V
OUT2
CC
RUN1
RUN2
FREQ
R
FREQ
41.2k
D2
TG2
MTOP2
C
SS2
0.01μF
C
0.1μF
B2
L2
8μH
R
TRACK/SS2
ITH2
BOOST2
SW2
SENSE2
10mΩ
R
ITH2
34.8k
C
470pF
V
8.5V
3A
ITH2
R
OUT2
C
OUT2
A2
10.5k
330μF
MBOT2
V
FB2
BG2
R
B2
100k
–
SENSE2
C2
1nF
+
SENSE2
3890 TA07a
MTOP1, MTOP2, MBOT1, MBOT2: RJK0651DPB
L1: COILCRAFT SER1360-472KL
L2: COILCRAFT SER1360-802KL
C
C
: SANYO 6TPE470M
: SANYO 10TPE330M
OUT1
OUT2
D1, D2: DFLS1100
Figure 13. High Efficiency Dual 8.5V/3.3V Step-Down Converter
Efficiency and Power Loss
vs Output Current
Efficiency vs Load Current
Efficiency vs Input Voltage
100
98
96
94
92
90
88
86
84
82
10000
1000
100
100
90
80
70
60
50
40
30
20
100
90
80
70
60
50
40
30
20
V
IN
V
OUT
= 12V
V
= 8.5V
BURST EFFICIENCY
OUT
= 3.3V
V
= 3.3V
OUT
V
= 8.5V
OUT2
CCM LOSS
BURST LOSS
PULSE-SKIPPING
LOSS
V
= 3.3V
10
OUT1
CCM EFFICIENCY
1
PULSE-SKIPPING
EFFICIENCY
10
0
10
0
I
= 2A
V
= 12V
LOAD
5
IN
80
0
0.1
10
10 15 20 25 30 35 40 45 50 55 60
0.0001 0.001
0.01
0.1
1
10
0.0001 0.001
0.01
0.1
1
INPUT VOLTAGE (V)
OUTPUT CURRENT (A)
OUTPUT CURRENT (A)
3890 TA07d
3890 TA07c
3890 TA07b
3890f
31
LTC3890
TYPICAL APPLICATIONS
High Efficiency 8.5V Dual-Phase Step-Down Converter
+
–
SENSE1
SENSE1
INTV
C1
1nF
CC
R
B1
100k
100k
R
A1
PGOOD1
PGOOD2
10.5k
V
FB1
MBOT1
C
100pF
ITH1A
BG1
L1
8μH
V
8.5V
6A
OUT1
SW1
R
34.8k
ITH1
C
R
SENSE1
BOOST1
ITH1
10mΩ
C
OUT1
330μF
C
ITH1
C
0.01μF
LTC3890
TRACK/SS1
B1
SS1
470pF
0.1μF
TG1
MTOP1
I
D1
LIM
V
PHSMD
CLKOUT
PLLIN/MODE
IN
INTV
V
R
CC
IN
MODE
9V TO 60V
C
IN
220μF
100k
INTV
CC
C
INT
SGND
4.7μF
R
PGND
RUN
V
OUT
EXTV
1000k
CC
V
IN
RUN1
RUN2
FREQ
D2
R
41.2k
FREQ
TG2
MTOP2
C
0.1μF
B2
TRACK/SS2
C
ITH2
100pF
R
L2
8μH
BOOST2
SW2
SENSE2
10mΩ
ITH2
C
OUT2
MBOT2
BG2
330μF
V
FB2
–
+
SENSE2
C2
1nF
SENSE2
3890 TA03
MTOP1, MTOP2, MBOT1, MBOT2: RJK0651DPB
L1, L2: COILCRAFT SER1360-802KL
C
, C
: SANYO 10TPE330M
OUT1 OUT2
D1, D2: DFLS1100
3890f
32
LTC3890
TYPICAL APPLICATIONS
High Efficiency Dual 12V/5V Step-Down Converter
+
SENSE1
INTV
CC
C1
1nF
R
B1
100k
100k
100k
–
PGOOD1
SENSE1
R
A1
6.98k
V
PGOOD2
BG1
FB1
C
100pF
R
ITH1A
MBOT1
R
SENSE1
9mΩ
V
12V
3A
OUT1
C
470pF
C
ITH1
ITH1
SW1
34.8k
L1
C
OUT1
BOOST1
ITH1
8μH
180μF
C
LTC3890
TRACK/SS1
0.01μF
B1
SS1
0.47μF
TG1
MTOP1
D1
I
LIM
V
IN
PHSMD
CLKOUT
PLLIN/MODE
V
IN
12.5V TO 60V
C
IN
220μF
INTV
CC
C
INT
SGND
4.7μF
PGND
EXTV
CC
RUN1
RUN2
FREQ
R
FREQ
D2
41.2k
TG2
MTOP2
C
0.47μF
C
SS2
0.01μF
B2
L2
4.7μH
R
BOOST2
SW2
SENSE2
10mΩ
TRACK/SS2
ITH2
V
5V
5A
OUT2
R
ITH2
20k
C
470pF
ITH2
C
OUT2
MBOT2
BG2
470μF
V
FB2
R
A2
–
+
SENSE2
18.7k
R
B2
C2
1nF
100k
SENSE2
3890 TA04
MTOP1, MTOP2, MBOT1, MBOT2: RJK0651DPB
L1: COILCRAFT SER1360-802KL
L2: COILCRAFT SER1360-472KL
C
C
: 16SVP180MX
OUT1
OUT2
: SANYO 6TPE470M
D1, D2: DFLS1100
3890f
33
LTC3890
TYPICAL APPLICATIONS
High Efficiency Dual 24V/5V Step-Down Converter
R
B1
487k
+
SENSE1
INTV
CC
C1
1nF
C
33pF
F1
100k
100k
–
SENSE1
PGOOD1
PGOOD2
BG1
R
A1
16.9k
V
FB1
C
100pF
R
ITH1A
L1
22μH
MBOT1
MTOP1
R
SENSE1
V
24V
1A
25mΩ
OUT1
C
680pF
C
ITH1
46k
ITH1
SW1
BOOST1
ITH1
C
OUT1
22μF
C
LTC3890
TRACK/SS1
0.01μF
B1
SS1
×2 CERAMIC
0.47μF
TG1
D1
I
LIM
V
IN
PHSMD
CLKOUT
PLLIN/MODE
V
IN
28V TO 60V
C
IN
220μF
INTV
CC
C
INT
SGND
4.7μF
PGND
EXTV
CC
RUN1
RUN2
FREQ
R
FREQ
D2
60k
TG2
MTOP2
C
0.47μF
C
SS2
0.01μF
R
B2
L2
4.7μH
R
BOOST2
SW2
SENSE2
TRACK/SS2
ITH2
10mΩ
V
C
470pF
ITH2
20k
OUT2
5V
5A
ITH2
C
OUT2
MBOT2
BG2
470μF
R
A2
18.7k
V
FB2
R
B2
100k
–
+
SENSE2
SENSE2
C2
1nF
3890 TA05
MTOP1, MTOP2, MBOT1, MBOT2: RJK0651DPB
L1: SUMIDA CDR7D43MN
L2: COILCRAFT SER1360-472KL
C
: KEMET T525D476MO16E035
: SANYO 6TPE470M
OUT1
OUT2
C
D1, D2: DFLS1100
3890f
34
LTC3890
PACKAGE DESCRIPTION
UH Package
32-Lead Plastic QFN (5mm × 5mm)
(Reference LTC DWG # 05-08-1693 Rev D)
0.70 p0.05
5.50 p0.05
4.10 p0.05
3.45 p 0.05
3.50 REF
(4 SIDES)
3.45 p 0.05
PACKAGE OUTLINE
0.25 p 0.05
0.50 BSC
RECOMMENDED SOLDER PAD LAYOUT
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
BOTTOM VIEW—EXPOSED PAD
PIN 1 NOTCH R = 0.30 TYP
OR 0.35 s 45o CHAMFER
R = 0.05
TYP
0.00 – 0.05
R = 0.115
TYP
0.75 p 0.05
5.00 p 0.10
(4 SIDES)
31 32
0.40 p 0.10
PIN 1
TOP MARK
(NOTE 6)
1
2
3.45 p 0.10
3.50 REF
(4-SIDES)
3.45 p 0.10
(UH32) QFN 0406 REV D
0.200 REF
0.25 p 0.05
0.50 BSC
NOTE:
1. DRAWING PROPOSED TO BE A JEDEC PACKAGE OUTLINE
M0-220 VARIATION WHHD-(X) (TO BE APPROVED)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
3890f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
35
LTC3890
TYPICAL APPLICATION
High Efficiency Dual 12V/3.3V Step-Down Converter
+
SENSE1
INTV
CC
C1
1nF
R
B1
100k
100k
100k
–
PGOOD1
SENSE1
R
A1
6.98k
V
PGOOD2
BG1
FB1
C
100pF
R
ITH1A
MBOT1
R
SENSE1
9mΩ
V
12V
3A
OUT1
C
470pF
ITH1
ITH1
SW1
34.8k
L1
8μH
C
OUT1
BOOST1
ITH1
180μF
C
LTC3890
TRACK/SS1
C
SS1
0.01μF
B1
0.47μF
TG1
MTOP1
D1
I
LIM
V
IN
PHSMD
CLKOUT
PLLIN/MODE
V
IN
12.5V TO 60V
C
IN
220μF
INTV
CC
C
INT
SGND
4.7μF
PGND
EXTV
CC
RUN1
RUN2
FREQ
R
FREQ
D2
41.2k
TG2
MTOP2
C
0.47μF
C
SS2
0.01μF
B2
L2
4.7μH
R
BOOST2
SW2
SENSE2
10mΩ
TRACK/SS2
ITH2
V
3.3V
5A
OUT2
R
ITH2
34.8k
C
1000pF
ITH2
C
C
OUT2
ITH2A
MBOT2
BG2
470μF
100pF
V
MTOP1, MTOP2, MBOT1, MBOT2: RJK0651DPB
L1: COILCRAFT SER1360-802KL
FB2
R
A2
–
SENSE2
31.6k
L2: COILCRAFT SER1360-472KL
R
B2
C2
1nF
C
C
: 16SVP180MX
: SANYO 6TPE470M
OUT1
OUT2
100k
+
D1, D2: DFLS1100
SENSE2
3890 TA06
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
Phase-Lockable Fixed Frequency 50kHz to 900kHz, 4V ≤ V ≤ 38V,
LTC3857/LTC3857-1 Low I , Dual Output 2-Phase Synchronous Step-Down
Q
IN
DC/DC Controllers with 99% Duty Cycle
0.8V ≤ V
≤ 24V, I = 50μA
OUT Q
LTC3858/LTC3858-1 Low I , Dual Output 2-Phase Synchronous Step-Down
Phase-Lockable Fixed Frequency 50kHz to 900kHz, 4V ≤ V ≤ 38V,
IN
Q
DC/DC Controllers with 99% Duty Cycle
0.8V ≤ V
≤ 24V, I = 170μA
OUT Q
LTC3868/LTC3868-1 Low I , Dual Output 2-Phase Synchronous Step-Down
Phase-Lockable Fixed Frequency 50kHz to 900kHz, 4V ≤ V ≤ 24V,
IN
Q
DC/DC Controller with 99% Duty Cycle
0.8V ≤ V
≤ 14V, I = 170μA
OUT Q
LTC3834/LTC3834-1 Low I , Synchronous Step-Down DC/DC Controller with Phase-Lockable Fixed Frequency 140kHz to 650kHz, 4V ≤ V ≤ 36V,
Q
IN
99% Duty Cycle
0.8V ≤ V ≤ 10V, I = 30μA
OUT Q
LTC3835/LTC3835-1 Low I , Synchronous Step-Down DC/DC Controller with Phase-Lockable Fixed Frequency 140kHz to 650kHz, 4V ≤ V ≤ 36V,
Q
IN
99% Duty Cycle
0.8V ≤ V ≤ 10V, I = 80μA
OUT Q
LT3845
Low I , High Voltage Synchronous Step-Down DC/DC
Adjustable Fixed Frequency 100kHz to 500kHz, 4V ≤ V ≤ 60V,
IN
Q
Controller
1.23V ≤ V
≤ 36V, I = 120μA, TSSOP-16
OUT Q
3890f
LT 0210 • PRINTED IN USA
LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
36
●
●
© LINEAR TECHNOLOGY CORPORATION 2010
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
相关型号:
LTC3890EUH#PBF
LTC3890 - 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller; Package: QFN; Pins: 32; Temperature Range: -40°C to 85°C
Linear
LTC3890EUH#TRPBF
LTC3890 - 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller; Package: QFN; Pins: 32; Temperature Range: -40°C to 85°C
Linear
LTC3890EUH-2#PBF
LTC3890-2 - 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller; Package: QFN; Pins: 32; Temperature Range: -40°C to 85°C
Linear
LTC3890HGN-1#PBF
LTC3890-1 - 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller; Package: SSOP; Pins: 28; Temperature Range: -40°C to 125°C
Linear
LTC3890HUH#PBF
LTC3890 - 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller; Package: QFN; Pins: 32; Temperature Range: -40°C to 125°C
Linear
LTC3890HUH-2#PBF
LTC3890-2 - 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller; Package: QFN; Pins: 32; Temperature Range: -40°C to 125°C
Linear
LTC3890IGN-1#PBF
LTC3890-1 - 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller; Package: SSOP; Pins: 28; Temperature Range: -40°C to 85°C
Linear
LTC3890IGN-1#TRPBF
LTC3890-1 - 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller; Package: SSOP; Pins: 28; Temperature Range: -40°C to 85°C
Linear
©2020 ICPDF网 联系我们和版权申明