LTW-006DCG-S52 [LITEON]
Package in 12mm tape on 7 diameter reels Compatible with automatic placement equipment; 在12毫米带包7直径卷筒兼容与自动贴装设备
| 型号： | LTW-006DCG-S52 |
| 厂家： | 
LITE-ON TECHNOLOGY CORPORATION |
| 描述： | Package in 12mm tape on 7 diameter reels Compatible with automatic placement equipment |
| 文件： | 总11页 (文件大小：437K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Features
* Package in 12mm tape on 7" diameter reels.
* Compatible with automatic placement equipment.
*
Compatible with infrared and vapor phase reflow solder process.
* EIA STD package.
* I.C. compatible.
* Meet green product and Pb-free(According to RoHS)
Package Dimensions
Anode
Part No.
Lens Color
Yellow
Source Color
InGaN White
LTW-006DCG-5
Notes:
1. All dimensions are in millimeters (inches).
±
2. Tolerance is 0.1 mm (.004") unless otherwise noted.
Part No. : LTW-006DCG-5
BNS-OD-C131/A4
Page :
1
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
℃
Absolute Maximum Ratings at Ta=25
Parameter
LTW-006DCG-5
120
Unit
mW
Power Dissipation
Peak Forward Current
mA
100
(1/10 Duty Cycle, 0.1ms Pulse Width)
DC Forward Current
30
5
mA
V
Reverse Voltage
℃ ℃
to + 85
Operating Temperature Range
Storage Temperature Range
Reflow Soldering Condition
-30
℃
℃
-40
to + 100
℃
260
For 10 Seconds
Note: Operating the LED (in an application) under reverse bias condition might result in damage
or failure of the component.
Suggest IR Reflow Condition :
R-Reflow Soldering Profile for lead free soldering (Acc. to J-STD-020D)
Part No. : LTW-006DCG-5
BNS-OD-C131/A4
Page :
2
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Electrical Optical Characteristics At Ta=25℃
Part No.
LTW-
Parameter
Symbol
IV
Min.
450
Typ.
Max.
750
Unit
Test Condition
IF = 5mA
Note 1, 2, 5
Luminous Intensity
Viewing Angle
006DCG-5
006DCG-5
mcd
deg
θ
110
2
1/2
Fig.6
IF = 5mA
Note 3, 5
Fig.1
x
0.277
0.255
Chromaticity Coordinates
006DCG-5
y
Forward Voltage
VF
006DCG-5
006DCG-5
2.65
200
3.25
V
V
IF = 5mA
HBM
ESD-Withstand Voltage
ESD
Note : 1. Luminous intensity is measured with a light sensor and filter combination that approximates the
CIE eye-response curve.
2. Iv classification code is marked on each packing bag.
3. The chromaticity coordinates (x, y) is derived from the 1931 CIE chromaticity diagram.
4. Caution in ESD:
Static Electricity and surge damages the LED. It is recommend to use a wrist band or
anti-E2lectrostatic glove when handling the LED. All devices, equipment and machinery
must be properly grounded.
5. CAS140B is the test standard for the chromaticity coordinates (x, y) & IV.
6. The chromaticity coordinates (x, y) guarantee should be added +/- 0.007 tolerance.
Part No. : LTW-006DCG-5
BNS-OD-C131/A4
Page :
3
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Bin Code List
VF Spec. Table
Forward Voltage (V) at IF = 5mA
VF Bin
Min.
2.65
2.75
2.85
2.95
3.05
3.15
Max.
2.75
2.85
2.95
3.05
3.15
3.25
V0
V1
V2
V3
V4
V5
V6
Tolerance on each Forward Voltage bin is +/-0.10 volt
IV Spec. Table
Luminous Intensity (mcd) at IF = 5mA
IV Bin
Min.
450
500
550
600
650
700
750
800
850
900
Max.
500
550
600
650
700
750
800
850
900
950
S41
S42
S51
S52
S61
S62
S71
S72
S81
S82
Tolerance on each Luminous Intensity bin is +/- 7%.
Part No. : LTW-006DCG-5
BNS-OD-C131/A4
Page :
4
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Color Ranks Table
Color bin limits at IF = 5mA
Ranks
CIE 1931Chromaticity coordinates
C12
C21
C22
C31
C32
B12
B21
B22
B31
B32
x
y
x
y
x
y
x
y
x
y
x
y
x
y
x
y
x
y
x
y
0.265
0.237
0.27
0.27
0.245
0.275
0.253
0.28
0.27
0.258
0.275
0.266
0.28
0.265
0.25
0.27
0.245
0.275
0.253
0.28
0.258
0.275
0.266
0.28
0.261
0.285
0.269
0.29
0.274
0.285
0.282
0.29
0.261
0.285
0.269
0.265
0.224
0.27
0.274
0.285
0.282
0.265
0.237
0.27
0.277
0.27
0.29
0.27
0.232
0.275
0.24
0.245
0.275
0.253
0.28
0.232
0.275
0.24
0.245
0.275
0.253
0.28
0.28
0.248
0.285
0.256
0.29
0.261
0.285
0.269
0.29
0.28
0.248
0.285
0.256
0.261
0.285
0.269
0.264
0.277
Tolerance on each Hue (x, y) bin is +/- 0.007.
C. I. E. 1931 Chromaticity Diagram @5mA
0.300
0.295
0.290
0.285
0.280
0.275
0.270
0.265
0.260
0.255
0.250
0.245
0.240
0.235
0.230
0.225
0.220
0.215
0.210
C32
B32
C31
B31
C22
B22
C21
B21
C12
B12
0.260
0.265
0.270
0.275
0.280
0.285
0.290
0.295
X-coordinate
Part No. : LTW-006DCG-5
BNS-OD-C131/A4
Page :
5
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Typical Electrical / Optical Characteristics Curves
C
(25° Ambient Temperature Unless Otherwise Noted)
Part No. : LTW-006DCG-5
BNS-OD-C131/A4
Page : 6
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
User Guide
Cleaning
Do not use unspecified chemical liquid to clean LED they could harm the package.
If cleaning is necessary, immerse the LED in ethyl alcohol or isopropyl alcohol at
normal temperature for less one minute.
Recommend Printed Circuit Board Attachment Pad
Infrared / vapor phase
Reflow Soldering
Package Dimensions of Tape
Note:
1.All dimensions are in millimeters (inches).
Part No. : LTW-006DCG-5
BNS-OD-C131/A4
Page :
7
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Package Dimensions of Reel
Notes:
1. Empty component pockets sealed with top cover tape.
2. 7 inch reel-2000 pieces per reel.
3. The maximum number of consecutive missing lamps is two.
4. In accordance with EIA-481-1-E2 specifications.
Part No. : LTW-006DCG-5
BNS-OD-C131/A4
Page :
8
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
CAUTIONS
1. Application
The LEDs described here are intended to be used for ordinary electronic equipment (such as office
equipment, communication equipment and household applications).Consult Liteon’s Sales in advance
for information on applications in which exceptional reliability is required, particularly when the failure
or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation,
traffic control equipment, medical and life support systems and safety devices).
2. Storage
This product is qualified as Moisture sensitive Level 3 per JEDEC J-STD-020 Precaution when handing
this moisture sensitive product is important to ensure the reliability of the product.
The package is sealed:
The LEDs should be stored at 30°C or less and 90%RH or less. And the LEDs are limited to use
within one year, while the LEDs is packed in moisture-proof package with the desiccants inside.
The package is opened:
The LEDs should be stored at 30°C or less and 60%RH or less. Moreover, the LEDs are limited to
solder process within 168hrs. If the Humidity Indicator shows the pink color in 10% even higher or
exceed the storage limiting time since opened, that we recommended to baking LEDs at 60°C at
least 48hrs. To seal the remainder LEDs return to package, it’s recommended to be with workable
desiccants in original package.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary.
4. Soldering
Recommended soldering conditions:
Reflow soldering
Soldering iron
Temperature 300°C Max.
Soldering time 3 sec. Max.
(one time only)
Pre-heat
Pre-heat time
Peak temperature 260°C Max.
Soldering time 30 sec. Max.
120~150°C
120 sec. Max.
5. Drive Method
An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs
connected in parallel in an application, it is recommended that a current limiting resistor be incorporated
in the drive circuit, in series with each LED as shown in Circuit A below.
Circuit model A
Circuit model B
LED
LED
(A) Recommended circuit.
(B) The brightness of each LED might appear different due to the differences in the I-V characteristics
of those LEDs.
Part No. : LTW-006DCG-5
BNS-OD-C131/A4
Page :
9
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
6. ESD (Electrostatic Discharge)
Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage:
ꢀ Use of a conductive wrist band or anti-E2lectrostatic glove when handling these LEDs.
ꢀ All devices, equipment, and machinery must be properly grounded.
ꢀ Work tables, storage racks, etc. should be properly grounded.
ꢀ Use ion blower to neutralize the static charge which might have built up on surface of the LED’s
plastic lens as a result of friction between LEDs during storage and handling.
ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low
forward voltage, or “ no lightup ” at low currents.
To verify for ESD damage, check for “ lightup ” and Vf of the suspect LEDs at low currents.
The Vf of “ good ” LEDs should be >2.0V@0.1mA for InGaN product
7.1 Reliability Test
Number of
Damaged
Test Item
Test Condition
Reference Standard
Note
Resistance to Soldering
Heat (Reflow Soldering)
JEITA ED-4701
300 301
Tsld=260℃, 10sec.
2 times
0/50
0/50
0/50
± ℃
Solderability
(Reflow Soldering)
Tsld=245 5 , 3sec.
1 time
Over 95%
JEITA ED-4701
300 303
(Lead Free Solder)
℃
℃
~ 85
-30
JEITA ED-4701
300 307
Thermal Shock
100 cycles
100 cycles
30min. 30min.
℃
℃
℃
℃
~ 25
-40
~ 25
~ 100
JEITA ED-4701
100 105
0/50
Temperature Cycle
30min. 5min. 30min. 5min.
JEITA ED-4701
200 201
Ta=100℃
High Temperature Storage
1000 hrs.
1000 hrs.
1000 hrs.
1000 hrs.
0/50
0/50
0/50
0/50
Temperature Humidity
Storage
JEITA ED-4701
100 103
Ta=60℃, RH=90%
Ta=-40℃
JEITA ED-4701
200 202
Low Temperature Storage
Steady State
Operating Life Condition 1
Ta=25℃, IF=20mA
Steady State
Operating Life Condition 2
Ta=25℃, IF=30mA
Ta=85℃, IF=5mA
500 hrs.
0/50
0/50
Steady State
Operating Life of High
Temperature
1000 hrs.
Steady State
60℃, RH=90% , IF=15mA
Ta=-30℃, IF=20mA
Operating Life of High
Humidity Heat
500 hrs.
0/50
0/50
Steady State
Operating Life of low
Temperature
1000 hrs.
Part No. : LTW-006DCG-5
BNS-OD-C131/A4
Page :
10
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
7.2 Criteria for Judging the Damage
Criteria for Judgment
Min. Max.
Item
Symbol
Test Conditions
U.S.L.*)
-
╳
1.1
Forward Voltage
VF
IV
IF=20mA
IF=20mA
-
U.S.L.**)
╳
0.7
Luminous Intensity
8. Others
The appearance and specifications of the product may be modified for improvement without prior notice.
9. Suggested Checking List
Training and Certification
1. Everyone working in a static-safe area is ESD-certified?
2. Training records kept and re-certification dates monitored?
Static-Safe Workstation & Work Areas
1. Static-safe workstation or work-E2reas have ESD signs?
2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V?
3. All ionizer activated, positioned towards the units?
4. Each work surface mats grounding is good?
Personnel Grounding
1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or
conductive shoes with conductive flooring?
2. If conductive footwear used, conductive flooring also present where operator stand or walk?
3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*?
4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs?
5. All wrist strap or heel strap checkers calibration up to date?
Note: *50V for Blue LED.
Device Handling
1. Every ESDS items identified by EIA-471 labels on item or packaging?
2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe
workstation?
3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items?
4. All flexible conductive and dissipative package materials inspected before reuse or recycle?
Others
1. Audit result reported to entity ESD control coordinator?
2. Corrective action from previous audits completed?
3. Are audit records complete and on file?
Part No. : LTW-006DCG-5
BNS-OD-C131/A4
Page :
11
of
11
相关型号：
LTW-006DCG-S61
Package in 12mm tape on 7 diameter reels Compatible with automatic placement equipment
LITEON
LTW-006DCG-S62
Package in 12mm tape on 7 diameter reels Compatible with automatic placement equipment
LITEON
LTW-006DCG-V0
Package in 12mm tape on 7 diameter reels Compatible with automatic placement equipment
LITEON
LTW-006DCG-V1
Package in 12mm tape on 7 diameter reels Compatible with automatic placement equipment
LITEON
LTW-006DCG-V2
Package in 12mm tape on 7 diameter reels Compatible with automatic placement equipment
LITEON
LTW-006DCG-V3
Package in 12mm tape on 7 diameter reels Compatible with automatic placement equipment
LITEON
LTW-006DCG-V4
Package in 12mm tape on 7 diameter reels Compatible with automatic placement equipment
LITEON
LTW-006DCG-V5
Package in 12mm tape on 7 diameter reels Compatible with automatic placement equipment
LITEON
©2020 ICPDF网 联系我们和版权申明