LTW-008ZDCG [LITEON]
Property of Lite-On Only; 精简版，关于财产只有
| 型号： | LTW-008ZDCG |
| 厂家： | 
LITE-ON TECHNOLOGY CORPORATION |
| 描述： | Property of Lite-On Only |
| 文件： | 总11页 (文件大小：458K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Features
* Package in 8mm tape on 7" diameter reels.
* Compatible with automatic placement equipment.
* Compatible with infrared and vapor phase reflow solder process.
* EIA STD package.
* I.C. compatible.
* Meet green product and Pb-free(According to RoHS)
Package Dimensions
Part No.
Lens Color
Yellow
Source Color
InGaN White
LTW-008ZDCG
Notes:
1. All dimensions are in millimeters (inches).
±
2. Tolerance is 0.05 mm (.002") unless otherwise noted.
Definition of Distance Between of PAD and Reflector
Symbol
Dimension (mm)
A: The distance between pad’s bottom and reflector.
B: The tolerance between right and left pad.
C: The distance between pad and reflector.
A
B
C
0
0
0
min
min
min
0.05 max
0.03 max
0.05 max
Part No. : LTW-008ZDCG
BNS-OD-C131/A4
Page :
1
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
℃
Absolute Maximum Ratings at Ta=25
Parameter
LTW-008ZDCG
120
Unit
mW
mA
Power Dissipation
Peak Forward Current
100
30
5
(1/10 Duty Cycle, 0.1ms Pulse Width)
DC Forward Current
mA
V
Reverse Voltage
℃ ℃
to + 85
Operating Temperature Range
Storage Temperature Range
Reflow Soldering Condition
-30
℃
℃
to + 100
-40
℃
260
For 10 Seconds
Suggest IR Reflow Condition :
R-Reflow Soldering Profile for lead free soldering (Acc. to J-STD-020B)
Part No. : LTW-008ZDCG
BNS-OD-C131/A4
Page :
2
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Electrical Optical Characteristics At Ta=25℃
Part No.
LTW-
Parameter
Symbol
IV
Min.
860
Typ.
Max.
1720
Unit
Test Condition
IF = 20mA
Note 1, 2, 5
Luminous Intensity
Viewing Angle
008ZDCG
008ZDCG
mcd
deg
θ
110
2
1/2
Fig.6
IF = 20mA
Note 3, 5
Fig.1
x
0.295
0.280
Chromaticity Coordinates
008ZDCG
y
Forward Voltage
VF
008ZDCG
008ZDCG
2.9
2K
3.6
V
V
IF = 20mA
HBM
ESD-Withstand Voltage
ESD
Note : 1. Luminous intensity is measured with a light sensor and filter combination that approximates the
CIE eye-response curve.
2. Iv classification code is marked on each packing bag.
3. The chromaticity coordinates (x, y) is derived from the 1931 CIE chromaticity diagram.
4. Caution in ESD:
Static Electricity and surge damages the LED. It is recommend to use a wrist band or
anti-electrostatic glove when handling the LED. All devices, equipment and machinery
must be properly grounded.
5. CAS140B is the test standard for the chromaticity coordinates (x, y) & IV.
6. The chromaticity coordinates (x, y) guarantee should be added +/- 0.01 tolerance.
Part No. : LTW-008ZDCG
BNS-OD-C131/A4
Page :
3
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Bin Code List
VF Spec. Table
Forward Voltage (V) at IF = 20mA
VF Bin
Min.
2.9
3.0
3.1
3.2
3.3
3.4
3.5
Max.
3.0
3.1
3.2
3.3
3.4
3.5
3.6
V0
V1
V2
V3
V4
V5
V6
Tolerance on each Forward Voltage bin is +/-0.10 volt
IV Spec. Table
Luminous Intensity (mcd) at IF = 20mA
IV Bin
Min.
Max.
S
T
A
B
C
D
860
1000
1200
1320
1440
1580
1720
1000
1200
1320
1440
1580
Tolerance on each Luminous Intensity bin is +/- 10%.
Part No. : LTW-008ZDCG
BNS-OD-C131/A4
Page :
4
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Bin Code List
Color Ranks Table
Color bin limits at IF = 20mA
CIE 1931Chromaticity coordinates
Ranks
A52
A53
A54
A61
A62
A63
BE1
BE2
BE3
BF1
BF2
BF3
BG1
BG2
BG3
x
y
x
y
x
y
x
y
x
y
x
y
x
y
x
y
x
y
x
y
x
y
x
y
x
y
x
y
x
y
0.280
0.248
0.288
0.239
0.272
0.258
0.282
0.272
0.288
0.262
0.295
0.253
0.291
0.287
0.296
0.276
0.301
0.265
0.299
0.294
0.302
0.283
0.305
0.272
0.309
0.305
0.311
0.294
0.313
0.283
0.272
0.258
0.280
0.248
0.275
0.281
0.275
0.281
0.282
0.272
0.288
0.262
0.287
0.295
0.291
0.287
0.296
0.276
0.296
0.304
0.299
0.294
0.302
0.283
0.307
0.315
0.309
0.305
0.311
0.294
0.282
0.272
0.288
0.262
0.282
0.272
0.287
0.295
0.291
0.287
0.296
0.276
0.296
0.304
0.299
0.294
0.302
0.283
0.307
0.315
0.309
0.305
0.311
0.294
0.319
0.328
0.320
0.317
0.321
0.306
0.288
0.262
0.295
0.253
0.291
0.287
0.296
0.276
0.301
0.265
0.299
0.294
0.302
0.283
0.305
0.272
0.309
0.305
0.311
0.294
0.313
0.283
0.320
0.317
0.321
0.306
* Color Coordinates Measurement allowance is ±0.01
Part No. : LTW-008ZDCG
BNS-OD-C131/A4
Page :
5
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Typical Electrical / Optical Characteristics Curves
(25°C Ambient Temperature Unless Otherwise Noted)
1.0
0.5
0.0
350
450
550
wavelength (nm)
Fig.1 RELATIVE INTENSITY VS. WAVELENGTH
650
750
Part No. : LTW-008ZDCG
BNS-OD-C131/A4
Page : 6
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
User Guide
Cleaning
Do not use unspecified chemical liquid to clean LED they could harm the package.
If cleaning is necessary, immerse the LED in ethyl alcohol or isopropyl alcohol at
normal temperature for less one minute.
Recommend Printed Circuit Board Attachment Pad
Infrared / vapor phase
Reflow Soldering
Package Dimensions of Tape
Note:
1.All dimensions are in millimeters (inches).
Part No. : LTW-008ZDCG
BNS-OD-C131/A4
Page :
7
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Package Dimensions of Reel
Notes:
1. Empty component pockets sealed with top cover tape.
2. 7 inch reel-2000 pieces per reel.
3. The maximum number of consecutive missing lamps is two.
4. In accordance with EIA-481-1-B specifications.
5. Vacate 20 cm (min) on start of packing tape and vacate 50 cm (min) on last of packing tape.
Part No. : LTW-008ZDCG
BNS-OD-C131/A4
Page :
8
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
CAUTIONS
1. Application
The LEDs described here are intended to be used for ordinary electronic equipment (such as office
equipment, communication equipment and household applications).Consult Liteon’s Sales in advance
for information on applications in which exceptional reliability is required, particularly when the failure
or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation,
traffic control equipment, medical and life support systems and safety devices).
2. Storage
The storage ambient for the LEDs should not exceed 85°C temperature or 60% relative humidity.
It is recommended that LEDs out of their original packaging are IR-reflowed within one week.
For extended storage out of their original packaging, it is recommended that the LEDs be stored in a
sealed container with appropriate desiccant, or in a desiccators with nitrogen ambient.
LEDs stored out of their original packaging for more than a week should be baked at about 60 deg C
for at least 24 hours before solder assembly.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary.
4. Soldering
Recommended soldering conditions:
Reflow soldering
Soldering iron
Temperature 300°C Max.
Soldering time 3 sec. Max.
(one time only)
Pre-heat
Pre-heat time
Peak temperature 260°C Max.
Soldering time 30 sec. Max.
120~150°C
120 sec. Max.
5. Drive Method
An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs
connected in parallel in an application, it is recommended that a current limiting resistor be incorporated
in the drive circuit, in series with each LED as shown in Circuit A below.
Circuit model A
Circuit model B
LED
LED
(A) Recommended circuit.
(B) The brightness of each LED might appear different due to the differences in the I-V characteristics
of those LEDs.
6. ESD (Electrostatic Discharge)
Static Electricity or power surge will damage the LED.
Suggestions to prevent ESD damage:
ꢀ Use of a conductive wrist band or anti-electrostatic glove when handling these LEDs.
ꢀ All devices, equipment, and machinery must be properly grounded.
ꢀ Work tables, storage racks, etc. should be properly grounded.
ꢀ Use ion blower to neutralize the static charge which might have built up on surface of the LED’s
plastic lens as a result of friction between LEDs during storage and handling.
Part No. : LTW-008ZDCG
BNS-OD-C131/A4
Page :
9
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward
voltage, or “ no lightup ” at low currents.
To verify for ESD damage, check for “ lightup ” and Vf of the suspect LEDs at low currents.
The Vf of “ good ” LEDs should be >2.0V@0.1mA for InGaN product
7.1 Reliability Test
Number of
Damaged
Test Item
Test Condition
Reference Standard
Note
Resistance to Soldering
Heat (Reflow Soldering)
Tsld=260℃, 10sec.
(Pre treatment 30℃,70%,168hrs.)
JEITA ED-4701
300 301
2 times
0/50
Solderability
(Reflow Soldering)
± ℃
Tsld=245 5 , 3sec.
(Lead Free Solder)
1 time
Over 95%
JEITA ED-4701
300 303
0/50
0/50
0/50
℃
℃
0
~ 100
JEITA ED-4701
300 307
Thermal Shock
20 cycles
15sec. 15sec. .
℃
℃
℃
℃
~ 25
-40
~ 25
~ 100
JEITA ED-4701
100 105
100 cycles
Temperature Cycle
30min. 5min. 30min. 5min.
25℃ ~ 65℃ ~ -10℃
90%RH 24HRS./1cycle
JEITA ED-4701
200 203
Moisture Resistance Cyclic
10 cycles
1000 hrs.
0/50
0/50
0/50
0/50
0/50
0/50
JEITA ED-4701
200 201
Ta=100℃
High Temperature Storage
Temperature Humidity
Storage
JEITA ED-4701
100 103
Ta=60℃, RH=90%
Ta=-40℃
1000 hrs.
JEITA ED-4701
200 202
Low Temperature Storage
ON/OFF TEST
1000 hrs.
1min on.1min off, IF=20mA,
Ta= -25℃, 60℃, 25℃,
30,000cycles
1000 hrs.
Steady State
Operating Life Condition 1
Ta=25℃, IF=20mA
Ta=25℃, IF=30mA
Ta=25℃, IF=20mA
Ta=85℃, IF=5mA
Steady State
Operating Life Condition 2
500 hrs.
0/50
0/50
Steady State
Operating Life Condition 3
10000 hrs.
Steady State
Operating Life of High
Temperature
Steady State
Operating Life of High
Humidity Heat
1000 hrs.
500 hrs.
1000 hrs.
48 min.
0/50
0/50
0/50
0/50
60℃, RH=90% , IF=20mA
Ta=-30℃, IF=20mA
Steady State
Operating Life of low
Temperature
100~2000~100Hz Sweep 4 min.
200m/s2
3 direction , 4 cycles
JEITA ED-4701
400 403
Vibration
3 mm , 5±1 sec.
5N , 10±1 sec.
Substrate Bending
Stick
JEITA ED-4702
JEITA ED-4702
1 time
1 time
0/50
0/50
Part No. : LTW-008ZDCG
BNS-OD-C131/A4
Page :
10
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
7.2 Criteria for Judging the Damage
Criteria for Judgment
Item
Symbol
Test Conditions
Min.
Max.
U.S.L.*) ╳ 1.1
-
Forward Voltage
Luminous Intensity
Color
VF
IV
IF=20mA
IF=20mA
IF=20mA
IF=20mA
-
L.S.L.**) ╳ 0.8
ccx
ccy
Shift – 0.005
Shift – 0.005
Shift + 0.005
Shift + 0.005
Color
*) U.S.L.: Upper Standard Level
8. Others
**) L.S.L.: Lower Standard Level
The appearance and specifications of the product may be modified for improvement without prior notice.
9. Suggested Checking List
Training and Certification
1. Everyone working in a static-safe area is ESD-certified?
2. Training records kept and re-certification dates monitored?
Static-Safe Workstation & Work Areas
1. Static-safe workstation or work-areas have ESD signs?
2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V?
3. All ionizer activated, positioned towards the units?
4. Each work surface mats grounding is good?
Personnel Grounding
1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or
conductive shoes with conductive flooring?
2. If conductive footwear used, conductive flooring also present where operator stand or walk?
3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*?
4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs?
5. All wrist strap or heel strap checkers calibration up to date?
Note: *50V for Blue LED.
Device Handling
1. Every ESDS items identified by EIA-471 labels on item or packaging?
2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe
workstation?
3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items?
4. All flexible conductive and dissipative package materials inspected before reuse or recycle?
Others
1. Audit result reported to entity ESD control coordinator?
2. Corrective action from previous audits completed?
3. Are audit records complete and on file?
Part No. : LTW-008ZDCG
BNS-OD-C131/A4
Page :
11
of
11
相关型号：
©2020 ICPDF网 联系我们和版权申明