WP710A10ID14V_15 [KINGBRIGHT]
T-1 (3mm) SOLID STATE LAMP;型号: | WP710A10ID14V_15 |
厂家: | KINGBRIGHT CORPORATION |
描述: | T-1 (3mm) SOLID STATE LAMP |
文件: | 总6页 (文件大小:315K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
T-1 (3mm) SOLID STATE LAMP
Part Number: WP710A10ID14V
High Efficiency Red
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
z Low power consumption.
z Popular T-1 diameter package.
z General purpose leads.
z Reliable and rugged.
z The High Efficiency Red source color devices are made
with Gallium Arsenide Phosphide on Gallium Phosphide
Orange Light Emitting Diode.
z Electrostatic discharge and power surge could damage
the LEDs.
z Long life - solid state reliability.
z Available on tape and reel.
z 14V internal resistor.
z It is recommended to use a wrist band or anti-
electrostatic glove when handling the LEDs.
z All devices, equipments and machineries must be
electrically grounded.
z RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
SPEC NO: DSAL0506
APPROVED: WYNEC
REV NO: V.5A
DATE: JAN/22/2015
DRAWN: L.Q.Xie
PAGE: 1 OF 6
CHECKED: Allen Liu
ERP: 1101029207
Selection Guide
Iv (mcd) [2]
V= 14V
Viewing
Angle [1]
Part No.
Dice
Lens Type
Min.
10
Typ.
20
2θ1/2
WP710A10ID14V
Notes:
High Efficiency Red (GaAsP/GaP)
Red Diffused
40°
*5
*10
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
λpeak
λD [1]
Δλ1/2
IF
Parameter
Peak Wavelength
Dominant Wavelength
Spectral Line Half-width
Forward Current
Device
Typ.
627
617
45
Max.
Units
Test Conditions
VF=14V
High Efficiency Red
High Efficiency Red
High Efficiency Red
High Efficiency Red
High Efficiency Red
nm
nm
nm
mA
uA
VF=14V
VF=14V
10.5
13.5
10
VF=14V
IR
Reverse Current
VR = 5V
Note:
1.Wavelength: +/-1nm.
2.Wavelength value is traceable to the CIE127-2007 compliant national standards.
3.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
High Efficiency Red
Units
mW
V
Power dissipation
160
16
5
Forward Voltage
Reverse Voltage
V
Operating Temperature
Storage Temperature
Lead Solder Temperature [1]
Lead Solder Temperature [2]
-40°C To +70°C
-40°C To +85°C
260°C For 3 Seconds
260°C For 5 Seconds
Notes:
1. 2mm below package base.
2. 5mm below package base.
SPEC NO: DSAL0506
APPROVED: WYNEC
REV NO: V.5A
DATE: JAN/22/2015
DRAWN: L.Q.Xie
PAGE: 2 OF 6
CHECKED: Allen Liu
ERP: 1101029207
High Efficiency Red
WP710A10ID14V
SPEC NO: DSAL0506
APPROVED: WYNEC
REV NO: V.5A
DATE: JAN/22/2015
DRAWN: L.Q.Xie
PAGE: 3 OF 6
CHECKED: Allen Liu
ERP: 1101029207
PACKING & LABEL SPECIFICATIONS
WP710A10ID14V
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAL0506
APPROVED: WYNEC
REV NO: V.5A
DATE: JAN/22/2015
DRAWN: L.Q.Xie
PAGE: 4 OF 6
CHECKED: Allen Liu
ERP: 1101029207
SPEC NO: DSAL0506
APPROVED: WYNEC
REV NO: V.5A
DATE: JAN/22/2015
DRAWN: L.Q.Xie
PAGE: 5 OF 6
CHECKED: Allen Liu
ERP: 1101029207
SPEC NO: DSAL0506
APPROVED: WYNEC
REV NO: V.5A
DATE: JAN/22/2015
DRAWN: L.Q.Xie
PAGE: 6 OF 6
CHECKED: Allen Liu
ERP: 1101029207
相关型号:
WP710A10ID5V
The High Efficiency Red source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Orange Light Emitting Diode.
KINGBRIGHT
WP710A10IT
Single Color LED, High Efficiency Red, Red Transparent, T-1, 3mm, ROHS COMPLIANT PACKAGE-2
KINGBRIGHT
WP710A10LSRD
Single Color LED, Super Bright Red, Diffused Red, T-1, 3mm, ROHS COMPLIANT PACKAGE-2
KINGBRIGHT
©2020 ICPDF网 联系我们和版权申明