WP710A10LID_15 [KINGBRIGHT]
T-1 (3mm) SOLID STATE LAMP;型号: | WP710A10LID_15 |
厂家: | KINGBRIGHT CORPORATION |
描述: | T-1 (3mm) SOLID STATE LAMP |
文件: | 总6页 (文件大小:315K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
T-1 (3mm) SOLID STATE LAMP
Part Number: WP710A10LID
High Efficiency Red
Features
Description
z Low power consumption.
z Popular T-1 diameter package.
z General purpose leads.
z Reliable and rugged.
The High Efficiency Red source color devices are made with
Gallium Arsenide Phosphide on Gallium Phosphide Orange
Light Emitting Diode.
z Long life - solid state reliability.
z Available on tape and reel.
z Low current IF=2mA operating.
z RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
SPEC NO: DSAL0510
APPROVED: WYNEC
REV NO: V.5A
DATE: JAN/21/2015
DRAWN: L.Q.Xie
PAGE: 1 OF 6
CHECKED: Allen Liu
ERP: 1101029029
Selection Guide
Iv (mcd) [2]
@ 2mA
Viewing
Angle [1]
Part No.
Dice
Lens Type
Min.
0.35
*0.2
Typ.
1
2θ1/2
WP710A10LID
Notes:
High Efficiency Red (GaAsP/GaP)
Red Diffused
40°
*0.6
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
λpeak
λD [1]
Δλ1/2
C
Parameter
Peak Wavelength
Dominant Wavelength
Spectral Line Half-width
Capacitance
Device
Typ.
627
617
45
Max.
Units
Test Conditions
IF=2mA
High Efficiency Red
High Efficiency Red
High Efficiency Red
High Efficiency Red
High Efficiency Red
High Efficiency Red
nm
nm
nm
pF
V
IF=2mA
IF=2mA
15
VF=0V;f=1MHz
IF=2mA
VF [2]
IR
Forward Voltage
1.7
2.5
10
Reverse Current
uA
VR = 5V
Notes:
1.Wavelength: +/-1nm.
2.Forward Voltage: +/-0.1V.
3.Wavelength value is traceable to the CIE127-2007 compliant national standards.
4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
High Efficiency Red
Units
mW
mA
mA
V
Power dissipation
75
30
160
5
DC Forward Current
Peak Forward Current [1]
Reverse Voltage
Operating/Storage Temperature
Lead Solder Temperature [2]
Lead Solder Temperature [3]
-40°C To +85°C
260°C For 3 Seconds
260°C For 5 Seconds
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. 2mm below package base.
3. 5mm below package base.
SPEC NO: DSAL0510
APPROVED: WYNEC
REV NO: V.5A
CHECKED: Allen Liu
DATE: JAN/21/2015
DRAWN: L.Q.Xie
PAGE: 2 OF 6
ERP: 1101029029
High Efficiency Red
WP710A10LID
SPEC NO: DSAL0510
APPROVED: WYNEC
REV NO: V.5A
DATE: JAN/21/2015
DRAWN: L.Q.Xie
PAGE: 3 OF 6
CHECKED: Allen Liu
ERP: 1101029029
PACKING & LABEL SPECIFICATIONS
WP710A10LID
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAL0510
APPROVED: WYNEC
REV NO: V.5A
DATE: JAN/21/2015
DRAWN: L.Q.Xie
PAGE: 4 OF 6
CHECKED: Allen Liu
ERP: 1101029029
SPEC NO: DSAL0510
APPROVED: WYNEC
REV NO: V.5A
DATE: JAN/21/2015
DRAWN: L.Q.Xie
PAGE: 5 OF 6
CHECKED: Allen Liu
ERP: 1101029029
SPEC NO: DSAL0510
APPROVED: WYNEC
REV NO: V.5A
DATE: JAN/21/2015
DRAWN: L.Q.Xie
PAGE: 6 OF 6
CHECKED: Allen Liu
ERP: 1101029029
相关型号:
WP710A10LSRD
Single Color LED, Super Bright Red, Diffused Red, T-1, 3mm, ROHS COMPLIANT PACKAGE-2
KINGBRIGHT
©2020 ICPDF网 联系我们和版权申明