ISL55110IRZ [INTERSIL]
Dual, High Speed MOSFET Driver; 双通道,高速MOSFET驱动器![ISL55110IRZ](http://pdffile.icpdf.com/pdf1/p00099/img/icpdf/ISL55110_526921_icpdf.jpg)
型号: | ISL55110IRZ |
厂家: | ![]() |
描述: | Dual, High Speed MOSFET Driver |
文件: | 总15页 (文件大小:309K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
ISL55110, ISL55111
®
Data Sheet
March 21, 2007
FN6228.1
Dual, High Speed MOSFET Driver
Features
The ISL55110 and ISL55111 are dual high speed mosfet
drivers intended for applications requiring accurate pulse
generation and buffering. Target applications include
Ultrasound, CCD Imaging, Automotive Piezoelectric
distance sensing and clock generation circuits.
• 5V to 12V Pulse Magnitude
• High Current Drive 3.5A
• 6ns Minimum Pulse Width
• 1.5ns Rise and Fall Times, 100pF Load Time
• Low Skew
With a wide output voltage range and low on resistance,
these devices can drive a variety of resistive and capacitive
loads with fast rise and fall times, allowing high speed
operation with low skew as required in large CCD array
imaging applications.
• 3.3V and 5V Logic Compatible
• In-Phase and Anti-Phase Outputs
• Small QFN and TSSOP Packaging
• Low Quiescent Current
The ISL55110 and ISL55111 are compatible with 3.3V and
5V logic families and incorporate tightly controlled input
thresholds to minimize the effect of input rise time on output
pulse width. The ISL55110 has a pair of in-phase drivers
while the ISL55111 has two drivers operating in antiphase.
Both inputs of the device have independent inputs to allow
external time phasing if required.
• Pb-free Plus Anneal Available (RoHS compliant)
Applications
• Ultrasound Mosfet Driver
• CCD Array Horizontal Driver
• Automotive Piezo Driver Applications
• Clock Driver Circuits
The ISL55110 has a power down mode for low power
consumption during equipment standby times, making it
ideal for portable products.
The ISL55110 and ISL55111 are available in 16 Ld Exposed
pad QFN packaging and 8 Ld TSSOP. Both devices are
specified for operation over the full -40°C to +85°C
temperature range.
Ordering Information
PART
PART
TEMP.
PKG.
DWG. #
NUMBER
MARKING RANGE (°C) PACKAGE
ISL55110IRZ* 55 110IRZ -40 to +85 16 Ld QFN L16.4x4A
(Note) (Pb-free)
Functional Block Diagram
ISL55110IVZ* 55110 IVZ -40 to +85 8 Ld TSSOP M8.173
ISLl55110 and ISL55111 DUAL DRIVER
(Note)
(Pb-free)
o
VDD
VH
OA
o
o
ISL55111IRZ* 55 11IRZ
(Note)
-40 to +85 16 Ld QFN L16.4x4A
(Pb-free)
IN-A
ISL55111IVZ* 55111 IVZ -40 to +85 8 Ld TSSOP M8.173
(Note)
o
o
(Pb-free)
*Add “-T” suffix for tape and reel.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
HIZ-QFN*
OB
IN-B
o
o
o
*
GND
o
POWER DOWN
* HIZ AVAILABLE IN QFN PACKAGE ONLY
* ISL55111 IN-B IS INVERTING
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2003, 2005, 2006. All Rights Reserved
1
All other trademarks mentioned are the property of their respective owners.
ISL55110, ISL55111
Pinout
ISL55110
(16 LD QFN)
TOP VIEW
ISL55111
(16 LD QFN)
TOP VIEW
16 15 14 13
16 15 14 13
OB
VDD
ENABLE
PD
12
11
10
9
1
2
3
4
OB
VDD
ENABLE
PD
12
11
10
9
1
2
3
4
GND
VH
GND
VH
OA
IN-B
OA
IN-B
5
6
7
8
5
6
7
8
ISL55110
ISL55111
(8 LD TSSOP)
(8 LD TSSOP)
TOP VIEW
TOP VIEW
VDD
1
2
3
4
8
OB
VDD
1
2
3
4
8 OB
PD
IN-B
IN-A
7
6
GND
VH
PD
IN-B
IN-A
7
6
GND
VH
5
OA
5
OA
Pin Descriptions
PIN
FUNCTION
VDD
VH
Logic Power.
Driver High Rail Supply
GND
PD
Ground, return for both VH rail and VDD Logic Supply.
Power Down. Active Logic High places part in Power Down Mode.
ENABLE
IN-A
QFN Packages only. Provides high speed logic HIZ control of driver outputs while leaving device logic power on.
Logic level input that drives OA to VH Rail or Ground. Not Inverted.
Logic level input that drive OB to VH Rail or Ground. Not inverted on ISL55110, Inverted on ISL55111.
Driver output related to IN-A.
IN-B, INB
OA
OB
Driver output related to IN-B.
FN6228.1
March 21, 2007
2
ISL55110, ISL55111
Absolute Maximum Ratings (T = +25°C)
Thermal Information
A
VH+ to GND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.0V
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5V
VIN_A, VIN_V, PDN, ENABLE. . . . . . . . (GND-0.5V) to (VDD+0.5V)
OA, OB. . . . . . . . . . . . . . . . . . . . . . . . . . . . .(GND-0.5) to (VH+0.5V)
Maximum Peak Output Current . . . . . . . . . . . . . . . . . . . . . . (300mA)
ESD HBM Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3KV
Thermal Resistance
θ
(°C/W)
JA
16 Ld (4x4) QFN Package (Note 2) . . . . . . . . . . . . .
8 Ld TSSOP Package (Note 1) . . . . . . . . . . . . . . . .
Maximum Junction Temperature (Plastic Package). . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C
(Lead Tips Only)
45
140
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T = T = T
A
J
C
NOTES:
1. θ is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
JA
2. θ is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
JA
Tech Brief TB379.
Recommended Operating Conditions
PARAMETER
DESCRIPTION
Driver Supply Voltage
CONDITIONS
MIN
5
TYP
MAX
13.2
5.5
UNIT
V
VH
VDD
12
Logic Supply Voltage
Ambient Temperature
Junction Temperature
2.7
-40
V
T
+85
°C
°C
A
T
+150
J
DC Electrical Specifications
PARAMETER
VH = +12V, VDD = 2.7V to 5.5V, T = +25°C, unless otherwise specified.
A
DESCRIPTION
TEST CONDITIONS
MIN
TYP
MAX
UNITS
LOGIC CHARACTERISTICS
VIX_LH
VIX_HL
VHYS
VIH
Logic Input Threshold - Low to High
Logic Input Threshold - High to Low
Logic Input Hysteresis
l
l
= 1µA: VIN_A, VIN_B
= 1µA: VIN_A, VIN_B
1.32
1.12
1.42
1.22
0.2
1.52
1.32
V
V
IH
IL
VIN_A,VIN_B
V
Logic Input High Threshold
Logic Input Low Threshold
Logic Input High Threshold
Logic Input Low Threshold
Input Current Logic High
Input Current Logic Low
PDN
2.0
0
VDD
0.8
VDD
0.8
20
V
VIL
PDN
V
VIH
ENABLE - QFN only
ENABLE - QFN only
VIN_A,VIN_B = VDD
VIN_A, VIN_B = 0V
PDN = VDD
2.0
0
V
VIL
V
IIX_H
IIX_L
II_H
10
10
10
10
nA
nA
nA
nA
mA
nA
20
Input Current Logic High
Input Current Logic Low
20
II_L
PDN = 0V
15
II_H
Input Current Logic High
Input Current Logic Low
ENABLE = VDD - QFN only
ENABLE = 0V - QFN only
12
II_L
-25
FN6228.1
March 21, 2007
3
ISL55110, ISL55111
DC Electrical Specifications
PARAMETER
(Continued)VH = +12V, VDD = 2.7V to 5.5V, T = +25°C, unless otherwise specified.
A
DESCRIPTION
TEST CONDITIONS
MIN
TYP
MAX
UNITS
DRIVER CHARACTERISTICS
R
Driver Output Resistance
Driver Output DC current (>2s)
Peak Output Current
OA, OB
3
6
Ω
mA
A
DS
I
I
100
3.5
DC
AC
Design Intent verified via
simulation.
VOH to VOL
Driver Output Swing Range
VH voltage to Ground
3
13.2
V
SUPPLY CURRENTS
I
I
Logic Supply Quiescent Current
Logic Supply Power Down Current
Driver Supply Quiescent Current
PDN = Low
4.0
6.0
12
15
mA
μA
μA
DD
PDN = High
DD-PDN
IH
PDN = Low, No resistive load
D
OUT
IH_PDN
Driver Supply Power Down Current
PDN = High
1
μA
AC Electrical Specifications VH = +12V, VDD = +3.6, T = +25°C, unless otherwise specified.
A
PARAMETER
DESCRIPTION
TEST CONDITIONS
MIN
TYP
MAX
UNITS
SWITCHING CHARACTERISTICS
t
t
Driver Rise/Fall Time
OA,OB: CL = No Load
R, F
10% to 90%, VOH-VOL = 12V
10% to 90%, VOH-VOL = 10V
1.0
1.0
ns
ns
t
t
Driver Rise/Fall Time
OA, OB CL = 1nF
6.7
ns
R, F
10% to 90%, VOH-VOL = 12V
Input to Output Propagation Delay
Input to Output Propagation Delay
Input to Output Propagation Delay
Input to Output Propagation Delay
Input to Output Propagation Delay
Input to Output Propagation Delay
Input to Output Propagation Delay
Input to Output Propagation Delay
Figure 2, Load 100pF/1k
Figure 2, Load 220pF
Figure 2, Load 330pF
Figure 2, Load 680pF
12.0
9.3
ns
ns
ns
ns
ns
ns
ns
ns
ns
tpdR
tpdF
tpdR
tpdF
12.5
10.2
12.9
10.6
14.1
12.1
<0.5
tpdR
tpdF
tpdR
tpdF
tSkewR
Channel to Channel tpdR Spread with same Figure 2, All Loads
loads both Channels
tSkewF
Channel to Channel tpdF Spread with same Figure 2, All Loads
loads both channels.
<0.5
ns
FMAX
TMIN
Maximum Operating Frequency
Minimum Pulse Width
70
6
MHz
ns
PDEN*
PDDIS*
TEN*
Power-down to Power-on Time
Power-on to Power-down Time
ENABLE to ENABLE Time (HIZ Off)
ENABLE to ENABLE TIme (HIZ On)
0.7
1.4
0.3
1.4
1.0
1.6
0.7
1.6
ms
ms
ms
ms
TDIS*
FN6228.1
March 21, 2007
4
ISL55110, ISL55111
VH = 12V
+3V
INPUT
+
0.1μF
4.7μF
INX
IN
≈0.4V
INPUT
OUTPUT
C
ISL55110
L
t
t
f
r
12V
INPUT RISE AND
FALL TIMES ≤2ns
90%
90%
OUTPUT
0V
10%
10%
FIGURE 1. TEST CIRCUIT RISE (T )/FALL(T ) THRESHOLDS
R
F
VH = 12V
+3V
INPUT
50%
+
50%
0.1μF
4.7μF
IN-X
IN
≈0.4V
tpdF
tpdR
50%
INPUT
OUTPUT
C
ISL55110
L
12V
INPUT RISE AND
FALL TIMES ≤2ns
50%
OUTPUT OA AND OB ISLS55110
OUTPUT OA ISLS55111
0V
12V
OUTPUT OB ISLS55111
50%
50%
0V
t
R = tpdR CHN1 - tpdR CHN2
SKEW
FIGURE 2. TEST CIRCUIT PROPAGATION TPD DELAY
FN6228.1
March 21, 2007
5
ISL55110, ISL55111
Typical Performance Curves (See Typical Performance Curves Discussion)
7.0
6.3
5.6
4.9
4.2
3.5
2.8
2.1
1.4
0.7
0.0
7.0
6.3
5.6
4.9
4.2
3.5
2.8
2.1
1.4
0.7
0.0
VDD 3.6V
+50mA
VDD 3.6V
-50mA
+85°C
+25°C
+85°C
+25°C
-40°C
11
-40°C
11
3
4
5
6
7
8
9
10
12
13
3
4
5
6
7
8
9
10
12
13
VH, DRIVE RAIL (V)
VH, DRIVE RAIL (V)
FIGURE 3. DRIVER RON vs VH SOURCE RESISTANCE
FIGURE 4. DRIVER RON vs VH SINK RESISTANCE
4.00
4.00
50mA
50mA
3.66
3.33
2.66
2.33
2.00
3.66
3.33
2.66
2.33
2.00
VH 5.0V
VH 12.0V
VH 12.0V
VH 5.0V
2.5
3.5
4.5
5.5
2.5
3.5
4.5
5.5
VDD (V)
VDD (V)
FIGURE 5. RON vs VDD SOURCE RESISTANCE
FIGURE 6. RON vs VDD SINK RESISTANCE
4.0
10
9
8
7
6
5
4
3
2
1
0
VDD 3.6V
3.8
3.6
3.4
3.2
3.0
VH 5V AND 12V
4.5 5.5
2.5
3.5
4
8
12
VDD (V)
VH, DRIVE RAIL (V)
FIGURE 7. IDD vs VDD QUIESCENT CURRENT
FIGURE 8. IDD vs VH @ 50MHz (NO LOAD)
FN6228.1
March 21, 2007
6
ISL55110, ISL55111
Typical Performance Curves (Continued) (See Typical Performance Curves Discussion)
100
200
VDD 3.6V
90
180
VDD 3.6V
80
160
70
60
50
40
30
20
10
0
140
120
100
80
60
40
20
0
4
8
12
4
8
12
VH, DRIVE RAIL (V)
VH, DRIVE RAIL (V)
FIGURE 9. QUIESCENT IH vs VH
FIGURE 10. IH vs VH @ 50MHz (NO LOAD)
15.0
13.5
12.0
10.5
9.00
7.50
6.00
4.50
2.00
0.50
0.00
200
VH 5.0V
VDD 3.6V
180
160
140
120
100
80
60
40
VH 5.0V
20
VDD 3.6V
0
50M
66M
100M
124M
128M
50M
66M
100M
124M
128M
TOGGLE FREQUENCY IN Hz
TOGGLE FREQUENCY IN Hz
FIGURE 11. IDD vs FREQUENCY (DUAL CHANNEL, NO
LOAD)L
FIGURE 12. IH vs FREQUENCY (DUAL CHANNEL, NO LOAD)
1.5
1.5
1.4
1.4
-40°C
+85°C
-40°C
1.3
1.3
1.2
1.1
1.0
1.2
1.1
+85°C
1.0
2.5
3.5
4.5
5.5
2.5
3.5
4.5
5.5
VDD (V)
VDD (V)
FIGURE 13. VIH LOGIC THRESHOLDS
FIGURE 14. VIL LOGIC THRESHOLDS
FN6228.1
March 21, 2007
7
ISL55110, ISL55111
Typical Performance Curves (Continued) (See Typical Performance Curves Discussion)
10
9
10
9
100pF/1k
330pF
680pF
1000pF
100pF/1k
680pF
330pF
1000pF
8
8
VH 12.0V
VDD 3.6V
7
7
6
6
5
5
4
4
3
3
2
2
1
1
VH 12.0V
VDD 3.6V
0
-40
0
-40
-10
+20
PACKAGE TEMP (°C)
+50
+85
-10
+20
PACKAGE TEMP (°C)
+50
+ 85
FIGURE 15. t vs TEMPERATURE
r
FIGURE 16. t vs TEMPERATURE
f
20
18
16
14
12
10
8
20
18
16
14
12
10
8
1000pF
680pF
1000pF
680pF
330pF
100pF/1k
6
6
330pF
4
4
100pF/1k
VH 12.0V
VDD 3.6V
VH 12.0V
VDD 3.6V
2
2
0
-40
0
-40
-10
+20
+50
+85
-10
+20
+50
+85
PACKAGE TEMP (°C)
PACKAGE TEMP (°C)
FIGURE 17. tpd vs TEMPERATURE
FIGURE 18. tpd vs TEMPERATURE
f
r
10
10
9
680pF
VH 12.0V
1000pF
330pF
100pF/1k
1000pF
9
8
7
6
5
4
3
2
100pF/1k
680pF
330pF
8
7
6
5
4
3
2
1
0
1
0
VH 12.0V
2.5
3.5
4.5
5.5
2.5
3.5
4.5
5.5
VDD (V)
VDD (V)
FIGURE 19. t vs VDD
r
FIGURE 20. t vs VDD
f
FN6228.1
March 21, 2007
8
ISL55110, ISL55111
Typical Performance Curves (Continued) (See Typical Performance Curves Discussion)
12.0
12.0
10.8
9.6
8.4
7.2
6.0
4.8
3.6
2.4
1.2
0.0
680pF
330pF
1000pF
680pF
330pF
100pF/1k
1000pF
10.8
9.6
8.4
7.2
6.0
4.8
3.6
2.4
1.2
0.0
100pF/1k
VDD 3.3V
VDD 3.3V
3
6
9
12
3
6
9
12
VH (V)
VDD (V)
FIGURE 21. t vs VH
FIGURE 22. t vs VH
f
r
20
20
VH 12.0V
VH 12.0V
18
16
14
12
18
16
14
12
10
8
10
8
6
6
4
4
680pF
330pF
100pF/1k
1000pF
2
0
2.5
2
0
2.5
680pF
4.5
330pF
100pF/1k
1000pF
3.5
4.5
5.5
3.5
5.5
VDD (V)
VDD (V)
FIGURE 23. tpd vs VDD
r
FIGURE 24. tpd vs VDD
f
20
20
VDD 3.3V
VDD 3.3V
18
16
14
12
18
16
14
12
10
8
10
8
6
6
4
680pF
330pF
4
100pF/1k
1000pF
330pF
680pF
9
100pF/1k
1000pF
2
0
2
0
3
6
12
3
6
9
12
VH (V)
VH (V)
FIGURE 25. tpd vs VH
r
FIGURE 26. tpd vs VH
f
FN6228.1
March 21, 2007
9
ISL55110, ISL55111
Typical Performance Curves (Continued) (See Typical Performance Curves Discussion)
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
VH 12.0V
VDD 3.6V
VH 12.0V
VDD 3.6V
680pF AND 330pF
330pF
680pF
0.0
-40
0.0
-40
-10
+20
+50
+85
-10
+20
PACKAGE TEMP (°C)
+50
+85
PACKAGE TEMP (°C)
FIGURE 27. tskew vs TEMPERATURE
r
FIGURE 28. tskew vs TEMPERATURE
f
1.0
1.0
VH 12.0V
VH 12.0V
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
680pF
680pF
0.1
0.0
2.5
330pF
330pF
2.5
3.5
4.5
5.5
3.5
4.5
5.5
VDD (V)
VDD (V)
FIGURE 29. tskew vs VDD
FIGURE 30. tskew vs VDD
f
r
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
VDD 3.3V
VDD 3.3V
680pF
680pF
330pF
330pF
3
6
9
12
3
6
9
12
VDD (V)
VDD (V)
FIGURE 31. tskew vs VH
r
FIGURE 32. tskew vs VH
f
FN6228.1
March 21, 2007
10
ISL55110, ISL55111
Pin Skew
Typical Performance Curves Discussion
Pin Skew measurements are based on the difference in
propagation delay of the two channels. Measurements are
made on each channel from the 50% point on the stimulus
point to the 50% point on the driver output. The difference in
the propagation delay for Channel A and Channel B is
considered to be Skew.
RON
RON Source tested by placing device in Constant Drive High
Condition and connecting -50mA constant current source to
the Driver Output. Voltage Drop measured from VH to Driver
Output for RON calculations.
RON Sink tested by placing device in Constant Driver Low
Condition and connecting a +50mA constant current source.
Voltage Drop from Driver Out to Ground measured for RON
Calculations.
Both Rising Propagation Delay and Falling Propagation
Delay are measured and reports as tSkewR and tSkewF.
50MHz Tests
50MHz Tests reported as No Load actually include
Evaluation board parasitics and a single TEK 6545 fet probe.
However no driver load components are installed, C6
through C9 and R3 through R6 are not populated.
Dynamic Tests
All dynamic tests are conducted with ISL55110, ISL55111
Evaluation Board(s). Driver Loads are soldered to the
Evaluation board. Measurements are collected with P6245
Active Fet Probes and TDS5104 Oscilloscope. Pulse
Stimulus is provided by HP8131 pulse generator.
General
Most dynamic measurements are presented in three ways.
First over temperature with a VDD of 3.6V and VH of 12.0V.
Second, at ambient with VH set to 12V and VDD data points
of 2.5V, 3.5V, 4.5V and 5.50V. Third, the ambient tests are
repeated with VDD of 3.3V and VH data points of 3V, 6V, 9V
and 12V.
The ISL55110, ISL55111 Evaluation Boards provide Test
Point Fields for leadless connection to either an Active Fet
Probe or Differential probe. TP-IN fields are used for
monitoring pulse input stimulus. TP-OA/B monitor Driver
Output waveforms. C6 and C7 are the usual placement for
Driver loads. R3 and R4 are not populated and provided for
User-Specified, more complex load characterization.
FN6228.1
March 21, 2007
11
ISL55110, ISL55111
rise and fall times. Use a ground plane if possible, or use
Detailed Description
separate ground returns for the input and output circuits. To
minimize any common inductance in the ground return,
separate the input and output circuit ground returns as close
to the ISL55110, ISL55111 as is possible.
The ISL55110 and ISL55111 are Dual High Speed Mosfet
Drivers intended for applications requiring accurate pulse
generation and buffering. Target applications include
Ultrasound, CCD Imaging, Automotive Piezoelectric
distance sensing and clock generation circuits.
Bypassing
The rapid charging and discharging of the load capacitance
requires very high current spikes from the power supplies. A
parallel combination of capacitors that has a low impedance
over a wide frequency range should be used. A 4.7μF
tantalum capacitor in parallel with a low inductance 0.1μF
capacitor is usually sufficient bypassing.
With a wide output voltage range and low On Resistance,
these devices can drive a variety of resistive and capacitive
loads with fast rise and fall times, allowing high speed
operation with low skew as required in large CCD array
imaging applications.
The ISL55110 and ISL55111 are compatible with 3.3V and
5V logic families and incorporate tightly controlled input
thresholds to minimize the effect of input rise time on output
pulse width. The ISL55110 has a pair of in-phase drivers
while the ISL55111 two drivers operating in antiphase. Both
inputs of the device have independent inputs to allow
external time phasing if required.
Output Damping
Ringing is a common problem in any circuit with very fast
rise or fall times. Such ringing will be aggravated by long
inductive lines with capacitive loads. Techniques to reduce
ringing include:
1. Reduce inductance by making printed circuit board traces
as short as possible.
In addition to power MOS drivers, the ISL55110, ISL55111 is
well suited for other applications such as bus, control signal,
and clock drivers on large memory of microprocessor
boards, where the load capacitance is large and low
propagation delays are required. Other potential applications
include peripheral power drivers and charge-pump voltage
inverters.
2. Reduce inductance by using a ground plane or by closely
coupling the output lines to their return paths.
3. Use small damping resistor in series with the output of the
ISL55110, ISL55111. Although this reduces ringing, it will
also slightly increase the rise and fall times.
4. Use good by passing techniques to prevent supply volt-
age ringing.
Input Stage
The input stage is a high impedance input with rise/fall
hysteresis. This means that the inputs will be directly
compatible with both TTL and lower voltage logic over the
entire VDD range. The user should treat the inputs as high
speed pins and keep rise and fall times to <2ns.
Power Dissipation Calculation
The Power dissipation equation has three components:
Quiescent Power Dissipation, Power dissipation due to
Internal Parasitics and Power Dissipation because of the
Load Capacitor.
Output Stage
Power dissipation due to internal parasitics is usually the
most difficult to accurately quantitize. This is primarily due to
Crow-Bar current which is a product of both the high and low
drivers conducting effectively at the same time during driver
transitions. Design goals always target the minimum time for
this condition to exist. Given that how often this occurs is a
product of frequency, Crowbar effects can be characterized
as internal capacitance.
The ISL55110, ISL55111 output is a high-power CMOS
driver, swinging between ground and VH. At VH = 12V, the
output impedance of the inverter is typically 3.0Ω. The high
peak current capability of the ISL55110, ISL55111 enables it
to drive a 330pF load to 12V with a rise time of <3.0ns over
the full temperature range. The output swing of the
ISL55110, ISL55111 comes within < 30mV of the VH and
Ground rails.
Lab tests are conducted with Driver Outputs disconnected
from any load. With design verification packaging, bond
wires are removed to aid in the characterization process.
Base on laboratory tests and simulation correlation of those
results, the following equation defines the ISL55110,
ISL55111 Power Dissipation per channel:
Application Notes
Although the ISL55110, ISL55111 is simply a dual level-
shifting driver, there are several areas to which careful
attention must be paid.
Grounding
P = VDD*3.3e-3 + 10pF*VDD^2*f + 135pF*VH^2*f +
CL*VH^2*f (Watts/Channel)
Since the input and the high current output current paths
both include the ground pin, it is very important to minimize
and common impedance in the ground return. Since the
ISL55111 has one inverting input, any common impedance
will generate negative feedback, and may degrade the delay,
FN6228.1
March 21, 2007
12
ISL55110, ISL55111
Where:
The maximum power dissipation actually produced by an IC
is the total quiescent supply current times the total power
supply voltage, plus the power in the IC due to the loads.
Power also depends on number of channels changing state
and frequency of operation. The extent of continuous active
pulse generation will greatly effect dissipation requirements.
1. 3.3mA is the quiescent Current from the VDD. This
forms a small portion of the total calculation. When figuring
two channel power consumption, only include this current
once.
2. 10pF is the approximate parasitic Capacitor
(Inverters, etc.), which the VDD drives
The user should evaluate various heat sink/cooling options
in order to control the ambient temperature part of the
equation. This is especially true if the user’s applications
require continuous, high speed operation. A review of the
Theta-j ratings of the TSSOP and QFN package clearly
show the QFN package to have better thermal
characteristics.
3. 135pF is the approximate parasitic at the DOUT and its
Buffers. This includes the effect of the Crow-bar Current.
4. CL is the Load capacitor being driven
Power Dissipation Discussion
Specifying continuous pulse rates, driver loads and driver
level amplitudes are key in determining power supply
requirements as well as dissipation / cooling necessities.
Driver Output patterns also impact these needs. The faster
the pin activity, the greater the need to supply current and
remove heat.
The reader is cautioned against assuming a calculated
level of thermal performance in actual applications. A
careful inspection of conditions in your application
should be conducted. Great care must be taken to
ensure Die Temperature does not exceed 150°C Absolute
Maximum Thermal Limits.
As detailed in the Power Dissipation Calculation Section,
Power Dissipation of the device is calculated by taking the
DC current of the VDD (logic) and VH Current (Driver rail)
times the respective voltages and adding the product of both
calculations. The average DC current measurements of IDD
and IH should be done while running the device with the
planned VDD and VH levels and driving the required pulse
activity of both channels at the desired operating frequency
and driver loads.
Important Note: The ISL55110, ISL55111 QFN package
metal plane is used for heat sinking of the device. It is
electrically connected to the negative supply potential
ground.
Power Supply Sequencing
The ISL55110, ISL55111 references both VDD and the VH
driver supplies with respect to Ground. Therefore apply
VDD, then VH. Digital Inputs should never be open. Do not
apply slow analog ramps to the inputs. Again place
decoupling as close to the package as possible for both VDD
and especially VH.
Therefore the user must address power dissipation relative
to the planned operating conditions. Even with a device
mounted per Note 1 or 2 under Thermal Information, given
the high speed pulse rate and amplitude capability of the
ISL55110, ISL55111, it is possible to exceed the +150°C
“absolute-maximum junction temperature”. Therefore, it is
important to calculate the maximum junction temperature for
the application to determine if operating conditions need to
be modified for the device to remain in the safe operating
area.
Special Loading
With most applications the user will usually have a special
load requirement. Please contact Intersil for Evaluation
Boards or to request a device characterization to your
requirements in our lab.
The maximum power dissipation allowed in a package is
determined according to:
T
- T
AMAX
JMAX
--------------------------------------------
P
=
DMAX
θ
JA
where:
• T
• T
= Maximum junction temperature
= Maximum ambient temperature
JMAX
AMAX
• θ = Thermal resistance of the package
JA
• P
DMAX
= Maximum power dissipation in the package
FN6228.1
March 21, 2007
13
ISL55110, ISL55111
Quad Flat No-Lead Plastic Package (QFN)
Micro Lead Frame Plastic Package (MLFP)
L16.4x4A
16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
(COMPLIANT TO JEDEC MO-220-VGGD-10)
MILLIMETERS
SYMBOL
MIN
NOMINAL
MAX
1.00
0.05
1.00
NOTES
A
A1
A2
A3
b
0.80
0.90
-
-
-
-
-
-
9
0.20 REF
9
0.18
2.30
2.30
0.25
0.30
2.55
2.55
5, 8
D
4.00 BSC
-
D1
D2
E
3.75 BSC
9
2.40
7, 8
4.00 BSC
-
E1
E2
e
3.75 BSC
9
2.40
7, 8
0.50 BSC
-
k
0.25
0.30
-
-
-
-
L
0.40
0.50
0.15
8
L1
N
-
16
4
4
-
10
2
Nd
Ne
P
3
3
-
-
0.60
12
9
θ
-
9
Rev. 2 3/06
NOTES:
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
3. Nd and Ne refer to the number of terminals on each D and E.
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
7. Dimensions D2 and E2 are for the exposed pads which provide
improved electrical and thermal performance.
8. Nominal dimensions are provided to assist with PCB Land
Pattern Design efforts, see Intersil Technical Brief TB389.
9. Features and dimensions A2, A3, D1, E1, P & θ are present when
Anvil singulation method is used and not present for saw
singulation.
10. Depending on the method of lead termination at the edge of the
package, a maximum 0.15mm pull back (L1) maybe present.
L minus L1 to be equal to or greater than 0.3mm.
FN6228.1
March 21, 2007
14
ISL55110, ISL55111
Thin Shrink Small Outline Plastic Packages (TSSOP)
M8.173
N
8 LEAD THIN SHRINK NARROW BODY SMALL OUTLINE
PLASTIC PACKAGE
INDEX
AREA
0.25(0.010)
M
B M
E
E1
-B-
INCHES
MIN
MILLIMETERS
GAUGE
PLANE
SYMBOL
MAX
0.047
0.006
0.051
0.0118
0.0079
0.120
0.177
MIN
-
MAX
1.20
0.15
1.05
0.30
0.20
3.05
4.50
NOTES
A
A1
A2
b
-
-
1
2
3
0.002
0.031
0.0075
0.0035
0.116
0.169
0.05
0.80
0.19
0.09
2.95
4.30
-
L
0.25
0.010
-
0.05(0.002)
SEATING PLANE
A
9
-A-
D
c
-
D
3
-C-
α
E1
e
4
A2
e
A1
0.026 BSC
0.65 BSC
-
c
b
0.10(0.004)
E
0.246
0.256
6.25
0.45
6.50
0.75
-
0.10(0.004) M
C
A M B S
L
0.0177
0.0295
6
N
8
8
7
NOTES:
o
o
o
o
0
8
0
8
-
α
1. These package dimensions are within allowable dimensions of
JEDEC MO-153-AC, Issue E.
Rev. 1 12/00
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm
(0.006 inch) per side.
4. Dimension “E1” does not include interlead flash or protrusions. Inter-
lead flash and protrusions shall not exceed 0.15mm (0.006 inch) per
side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. Dimension “b” does not include dambar protrusion. Allowable dambar
protrusion shall be 0.08mm (0.003 inch) total in excess of “b” dimen-
sion at maximum material condition. Minimum space between protru-
sion and adjacent lead is 0.07mm (0.0027 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimensions
are not necessarily exact. (Angles in degrees)
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN6228.1
March 21, 2007
15
相关型号:
©2020 ICPDF网 联系我们和版权申明