HYB25D128323C-3.6 [INFINEON]
128 Mbit DDR SGRAM; 128兆位的DDR SGRAM型号: | HYB25D128323C-3.6 |
厂家: | Infineon |
描述: | 128 Mbit DDR SGRAM |
文件: | 总53页 (文件大小:1117K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Data Sheet, V1.7, July 2003
HYB25D128323C[-3/-3.3]
HYB25D128323C[-3.6/L3.6]
HYB25D128323C[-4.5/L4.5]
HYB25D128323C-5
128 Mbit DDR SGRAM
Memory Products
N e v e r s t o p t h i n k i n g .
Edition 2003-07
Published by Infineon Technologies AG,
St.-Martin-Strasse 53,
81669 München, Germany
© Infineon Technologies AG 2003.
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as a guarantee of
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding
circuits, descriptions and charts stated herein.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
Data Sheet, V1.7, July 2003
HYB25D128323C[-3/-3.3]
HYB25D128323C[-3.6/L3.6]
HYB25D128323C[-4.5/L4.5]
HYB25D128323C-5
128 Mbit DDR SGRAM
Memory Products
N e v e r s t o p t h i n k i n g .
HYB25D128323C[-3/-3.3], HYB25D128323C[-3.6/L3.6], HYB25D128323C[-4.5/L4.5], HYB25D128323C-5
Revision History:
V1.7
2003-07
Previous Version:
V1.51
2002-07
Page
all
Subjects (major changes since last revision)
new data sheet template
43
AC Operation Conditions: Input Slew Rate added
46
Timing Parameters for speed sorts –3, –3.3, –3.6, –4.5, and –5: Write DQS High/Low added
Timing Parameters for speed sorts L3.6 and L4.5: Write DQS High/Low added
48
Previous Version:
V1.51
2002-07
9, 13, 42, 46, extended VDD range for –3.6 and L3.6
48
We Listen to Your Comments
Any information within this document that you feel is wrong, unclear or missing at all?
Your feedback will help us to continuously improve the quality of this document.
Please send your proposal (including a reference to this document) to:
techdoc.mp@infineon.com
Template: mp_a4_v2.0_2003-06-06.fm
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Table of Contents
1
1.1
1.2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3
3.1
3.2
3.3
3.3.1
3.4
3.4.1
3.4.2
3.4.3
3.4.3.1
3.4.3.2
3.5
3.5.1
3.5.2
3.5.3
3.5.4
3.5.5
3.5.6
3.5.7
3.5.8
3.5.9
3.5.10
3.5.11
3.5.12
3.5.13
3.5.14
3.5.15
3.5.16
3.6
3.6.1
3.6.2
3.6.3
3.6.4
3.6.5
3.6.6
3.7
Register Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Mode Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Extended Mode Register Setup (EMRS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Signal and Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Special Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Clock Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Command Inputs and Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Data Strobe and Data Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Operation at Burst Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Operation at Burst Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Description of Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Power-Up Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Mode Register Set Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Extended Mode Register Set Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Bank Activation Command (ACT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Precharge Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Self Refresh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Auto Refresh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Power Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Burst Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Burst Read Operation: (READ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Burst Write Operation (WRITE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Burst Stop Command (BST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Data Mask (DMx) Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Autoprecharge Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Read with Autoprecharge (READA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Write with Autoprecharge (WRITEA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Burst Interruption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Read Interrupted by a Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Read Interrupted by a Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Read Interrupted by a Precharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Write Interrupted by a Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Write Interrupted by a Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Write Interrupted by a Precharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Operations and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Function Truth Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
DDR SGRAM Simplified State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.8
3.9
4
5
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Data Sheet
5
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
List of Figures
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Ball Out 128Mbit DDR SGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Functional blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Mode Register Bitmap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Extended Mode Register Bitmap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Command and Address Signal Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
DQS Timing for Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DQS and DM Timing at Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DQS Pre/Postamble at Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Power-Up Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 10 Mode Register Set Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 11 Activate to Read or Write Command Timing (one bank) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 12 Activate Bank A to Activate Bank B Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 13 Precharge Command Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 14 Self Refresh timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 15 Autorefresh timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 16 Power Down Mode timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 17 Burst Read Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 18 Burst Write Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 19 Burst Stop for Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 20 Data Mask Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 21 Read Burst with Autoprecharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 22 Read Concurrent Auto Precharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 23 Write Burst with Auto Precharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 24 Read interrupted by Read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 25 Read interrupted by Write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 26 Read interrupted by Precharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 27 Write interrupted by Write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 28 Write interrupted by Read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 29 Write interrupted by Precharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 30 DDR SGRAM Simplified State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 31 Output Test Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 32 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Data Sheet
6
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Data Sheet
7
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
List of Tables
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Signal and Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
IO Driver Strength and Interface Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Mapping of DQSx and DMx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Precharge Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Burst Mode and Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Concurrent Read Auto Precharge Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Concurrent Write Auto Precharge Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Command Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Function Truth Table I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Function Truth Table for CKE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Power & DC Operation Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
AC Operation Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Pin Capacitances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Timing Parameters for speed sorts –3, –3.3, –3.6, –4.5, and –5 . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Timing Parameters for speed sorts L3.6 and L4.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
HYB25D128323C–3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
HYB25D128323C–3.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
HYB25D128323C–3.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
HYB25D128323C–4.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
HYB25D128323C–5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
HYB25D128323CL3.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
HYB25D128323CL4.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Operating Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Table 20
Table 21
Table 22
Table 23
Table 24
Table 25
Table 26
Data Sheet
8
V1.7, 2003-07
128 Mbit DDR SGRAM
HYB25D128323C[-3/-3.3]
HYB25D128323C[-3.6/L3.6]
HYB25D128323C[-4.5/L4.5]
HYB25D128323C-5
1
Overview
1.1
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Maximum clock frequency up to 333 MHz
Maximum data rate up to 666 Mbps/pin
Data transfer on both edges of clock
Programmable CAS latency of 2, 3 and 4 clocks
Programmable burst length of 2, 4 and 8
Integrated DLL to align DQS and DQ transitions with CLK
Data transfer signals are synchronized with byte wise bidirectional Data Strobe
Data Strobe signal edge-aligned with data for Read operations
Data Strobe signal center aligned with data for Write operations
Differential clock inputs (CLK and CLK)
Data mask for masking write data, one DM per byte
Organization 1024K × 32 × 4 banks
4096 rows and 256 columns per bank
4K Refresh (32ms)
Refresh Interval 7.8 µsec
Autorefresh and Self Refresh available
Standard JEDEC TF-XBGA 128 package
Self-mirrored, symmetrical ball out
Matched Impedance Mode interface (Z0=60Ω)
SSTL-2 JEDEC Weak Mode interface (Z0=34Ω)
IO voltage VDDQ = 2.5 V
V
DD power supply memory core:
– Speed sorts –3 and –3.3: 2.5 V < VDD < 2.9 V
– Speed sorts L4.5, –4.5, and –5: VDD = 2.5 V
– Speed sorts L3.6 and –3.6 support both VDD modes
Table 1
Performance
Part Number Speed Code
–3
–3.3
3.3
–3.6
3.6
–4.5
4.5
–5.0
5.0
L3.6
3.6
L4.5
4.5
Unit
ns
CAS Latency 4
tCK4min.
fCK4max.
tCK3min.
fCK3max.
tQH
3
333
4.0
250
1.05
0.30
300
4.0
278
4.2
222
4.5
200
5.0
278
4.2
222
4.5
MHz
ns
CAS Latency 3
250
1.15
0.30
238
1.26
0.33
222
1.58
0.45
200
1.75
0.5
238
1.26
0.33
222
1.58
0.45
MHz
ns
Data Out Window
DQS-DQ Skew
tDQSQ
ns
1.2
Description
The Infineon 128Mbit DDR SGRAM is a ultra high performance graphics memory device, designed to meet all
requirements for high bandwidth intensive applications like PC graphics systems.
The 128Mbit DDR SGRAM uses a double-data-rate DRAM architecture organized as 4 banks × 4096 rows × 256
columns × 32 bits. The double-data-rate architecture is essentially a 2n prefetch architecture, with an interface
designed to transfer two data words per clock cycle at the I/O pins. A single Read or Write access to the DDR
Data Sheet
9
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Overview
SGRAM consists of a single 64-bit wide, one clock cycle data transfer at the internal DRAM core and two
corresponding 32-bit wide, one-half clock cycle data transfers at the I/O pins. The result is a data rate of 666 Mbits
/ sec per pin. The external data interface is 32 bit wide and achieves at 333 MHz system clock a peak bandwidth
of 2.66 Gigabytes/sec.
The device is supplied with 2.5 V resp. within the range of 2.5 V - 2.9 V for the memory core and 2.5 V for the
output drivers. Two drivers strengths are available: 2.5 V Matched Impedance Mode and SSTL2 Weak Mode. The
“Matched Impedance Mode” interface is optimized for high frequency digital data transfers and matches the
impedance of graphics board systems (60Ohm).
Auto Refresh and Self Refresh operations are both supported.
A standard JEDEC TF-XBGA 128 package is used which enables ultra high speed clock and data transfer rates.
The signals are mapped symmetrically to the balls in order to enable mirrored mounting in application.
The chip is fabricated in Infineon technologies advanced 256M process technology.
Data Sheet
10
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Pin Configuration
2
Pin Configuration
11
1
2
3
4
5
6
7
8
9
10
12
DQS0 DM0
DQ3
VDDQ
VSSQ
VSS
DQ2
DQ1
VSSQ
VSSQ
DQ0
DQ31
DQ28 VSSQ
DM3 DQS3
VDDQ DQ27
VSSQ
DQ29
DQ30
VSSQ
VSSQ
A
B
C
D
E
F
DQ4
VDDQ
NC
VDDQ
VDDQ VDDQ
NC
DQ6
DQ7
DQ5
VSSQ
VDD
VDD
VSS
VDD
VSS
VSSQ
VSS
VSSQ DQ26 DQ25
VDD VDDQ DQ24
VDDQ
DQ17 DQ16
DQ19 DQ18
DQS2 DM2
DQ21 DQ20
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSS
VSSQ VDDQ DQ15 DQ14
VSSQ VDDQ DQ13 DQ12
VDDQ
VDDQ
NC
TOP VIEW
128 BALL XBGA
4 Banks x 4096 Rows
VSSQ
DM1 DQS1
NC
G
H
J
x 256 Columns x 32 Bits
VSSQ VDDQ DQ11 DQ10
VDDQ
VDDQ
VDD
DQ22
CAS# WE#
VSS
A10
A2
VSS
VDD
A9
DQ9
NC
DQ8
NC
DQ23
VSS
VDD
A11
A3
VSS
VSSQ VDDQ
VSS
VDD
RFU
A5
K
L
BA1
A0
CLK CLK#
A8/AP CKE
RAS#
CS#
NC
NC
NC
RFU
A7
MCL
VREF
BA0
A1
A4
A6
M
Figure 1
Ball Out 128Mbit DDR SGRAM
Note:The inner matrix of 4 × 4 balls will be used as thermal VSS contacts ncluding the thermal VSS contacts, the
total amount of balls is 144
Data Sheet
11
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Pin Configuration
Table 2
Pin
Signal and Pin Description
IO Type Detailed Function
CLK, CLK
Input
Clock: CLK and CLK# are differential clock inputs. All address and command inputs
are latched on the crossing of the positive edge of CLK and the negative edge of CLK.
Output data (DQ’s and DQS) is referenced to the crossing of CLK and CLK.
CKE
Input
Clock Enable: CKE HIGH activates and CKE LOW deactivates the internal clock,
input buffers and output drivers. Taking CKE LOW provides PRECHARGE POWER-
DOWN and SELF REFRESH operations (all banks idle), or ACTIVE POWER-DOWN
(row active in any bank). CKE is synchronous for POWER-DOWN entry and exit, and
for SELF REFRESH entry. CKE is asynchronous for SELF-REFRESH exit. CKE must
be maintained HIGH trough out READ and WRITE accesses. Input buffers (excluding
CLK, CLK) are disabled during POWER-DOWN. Input buffers (excluding CKE) are
disabled during SELF REFRESH. CKE is an SSTL2 input but will detect an LVCMOS
LOW level after VDD is applied.
CS
Input
Chip Select: CS# enables the command decoder when low and disables it when high.
When the command decoder is disabled, new commands are ignored, but internal
operations continue. CS# is considered part of the command code.
RAS, CAS, WE Input
Command Inputs: CAS, RAS, and WE (along with CS) define the command to be
executed.
BA1, BA0
Input
Bank Address Inputs: BA0 and BA1 select to which internal bank an ACTIVE, READ,
WRITE, or PRECHARGE command is being applied. They also define which mode
register (mode register or extended mode register) is loaded during a MODE
REGISTER SET command.
A11.. A0
Input
Address Inputs: During a Bank Activate command cycle, A0-A11 defines the row
address (RA0-RA11). During a Read or Write command cycle, A0-A7 defines the
column address (CA0-CA7).
In addition to the column address, A8/AP is used to invoke autoprecharge operation
at the end of the burst read or write cycle. If A8 is high, the active bank is precharged.
If A8 is low, the Autoprecharge function is disabled.
During a Precharge command cycle, A8/AP is used to determine, which bank(s) will
be precharged. If A8/AP is high, all four banks will be precharged regardless of the
state of BA0 and BA1. If A8/AP is low, BA0 and BA1 define the bank to be precharged.
The address inputs also provide the op-code during a MODE REGISTER SET
command.
DQS3.. DQS0 I/O
Data Strobes: The DQSx are the bidirectional strobe signals. At read cycles, the
DQSx signals are generated by the SGRAM and are edge-aligned to the data. At write
cycles, the DQS signals are generated by the controller. The rising or falling edge
indicates the center of the data valid window. Before and after a transfer cycle, DQSx
enters a preamble and a postamble state. The DQSx signals are mapped to the
following data bytes: DQS0 to DQ0.. DQ7, DQS1 to DQ8.. DQ15, DQS2 to
DQ16..DQ23, DQS3 to DQ24.. DQ31.
DQ31.. DQ0
I/O
Data Input/Output: The DQx signals form the 32 bit wide data bus. At READ cycles
the pins are outputs and during WRITE cycles inputs. The data is transferred at both
edges of the DQSx signals.
Data Sheet
12
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Pin Configuration
Table 2
Pin
Signal and Pin Description (cont’d)
IO Type Detailed Function
DM3.. DM0
Input
Input Data Mask: The DM signals are input mask signal for WRITE data. They mask
off a complete byte on the data bus. DMx = 1 prevents the corresponding byte from
being written. DM3 corresponds to DQ31..DQ24, DM2 to DQ23..DQ16, DM1 to
DQ15..DQ8, DM0 to DQ7..DQ0. DM signals are sampled on both edges of DQS.
Although DM pins are input-only, the DM loading is designed to match that of DQ and
DQS pins.
VREF
Input
Voltage Reference: VREF is the reference voltage input signal.
VDD, VSS
Supply Power Supply: Power and Ground for the internal logic.
DD = 2.5 V ±5% for L4.5, –4.5, and -5
V
2.5 V – 5% < VDD < 2.9 V for –3.6 and L3.6
2.5 V < VDD < 2.9 V for –3 and –3.3
VDDQ, VSSQ
Supply IO Power Supply: Isolated Power and Ground for the output buffers to provide
improved noise immunity. VDDQ = 2.5V ± 5%
NC, RFU
MCL
–
–
Please do not connect No Connect, Reserved for Future Use pins.
Must be connected to low
Data Sheet
13
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Pin Configuration
Column Addresses A7-A0, AP
Column Address Buffer
Row Addresses A11-A0, BA1-BA0
Row Address Buffer
Column Address Counter
Row Decoder
Row Decoder
Row Decoder
Row Decoder
Memory
Array
Memory
Array
Memory
Array
Memory
Array
Bank 0
Bank 1
Bank 2
Bank 3
4096 x 256
x 32 bit
4096 x 256
x 32 bit
4096 x 256
x 32 bit
4096 x 256
x 32 bit
Input Buffers
Output Buffers
CLK
CLK#
CKE
DQ31-DQ24
DQ23-DQ16
DQ15-DQ8
DQ7-DQ0
CS#
RAS#
CAS#
WE#
V
ref
Figure 2
Functional blocks
Data Sheet
14
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
3
Register Set
3.1
Mode Register
The mode register stores the data for controlling the various operating modes of the DDR SGRAM. It programs
CAS latency, addressing mode, burst length, test mode, DLL ON and various vendor specific options. The default
value of the mode register is not defined. Therefore the mode register must be written after power up to operate
the DDR SGRAM. The DDR SGRAM should be activated with CKE already high prior to writing into the Mode
Register. The Mode Register is written by using the MRS command. The state of the address signals registered
in the same cycle as MRS command is written in the mode register. The value can be changed as long as all banks
are in the idle state.
The mode register is divided into various fields depending on functionality. The burst length uses A2.. A0, CAS
latency (read latency from column address) uses A6.. A4. A7 is used for test mode, A8 is used for DLL Reset. A7,
A8 and BA1 must be set to low for normal DDR SGRAM operation. A9.. A11 is reserved for future use. BA0 selects
Extended Mode Register Setup operation when set to 1. Refer to the table for specific codes for various burst
length, addressing modes and CAS latencies.
Address Bus
BA1
0
BA0
0
A11
A10
A9
A8
A7
A6
A5
A4
A3
BT
A2
A1
A0
RFU
RFU
RFU
DLL
TM
CAS Latency
Burst Length
Mode Register
Extended Mode
Register Access
Burst Type
A3 Type
Testmode
A7
BA0
Accessed Register
mode
0
1
Mode Register
0
1
Normal
0
1
Sequential
Reserved
Extend. Mode Reg.
Testmode
DLL Reset
CAS Latency
A8
DLL Reset
A6
A5
A4
Latency
0
1
No
0
0
1
1
1
0
0
1
0
2
3
4
Yes
All other Reserved
Burst Length
Length
A2
A1
A0
Sequential
Interleave
0
0
0
0
1
1
1
0
1
2
4
8
2
4
8
All other Reserved
Figure 3
Mode Register Bitmap
Data Sheet
15
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
3.2
Extended Mode Register Setup (EMRS)
The Extended Mode Register is responsible for enabling / disabling the DLL in the HYB25D128323C and for
selecting the interface type for the IOs and input pins. The Extended Mode Register can be programmed by
performing a normal Mode Register Setup operation and setting the BA0 bit to high. All other bits of the EMRS
register are reserved and should be set to low.
The Bit A0 enables / disables the DLL.
The Bits A1 and A6 set the driver strength of the IOs. For detailed explanation, refer to the following table.
Table 3
A6
IO Driver Strength and Interface Settings
A1
Drive Strength
Strength/
IO Power Supply Comment
VDDQ
Impedance
0
0
1
1
0
1
0
1
SSTL-2 weak
SSTL-2 weak
RFU
60% / 34Ohm
60% / 34Ohm
RFU
2.5V
2.5V
RFU
2.5V
replacement for strong mode
–
Do not use
matched
impedance mode
30% / 60Ohm
output driver matches line
impedance
Note:The combination A6=0 and A1=0 defines SSTL-2 strong mode in 32M DDR SGRAM which is not supported
in this device.
Address Bus
BA1
0
BA0
1
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
RFU must be set to "0"
DS1
RFU must be set to "0"
DS0
DLL
Extended Mode Register
Extended Mode
Register Access
BA0
Accessed Register
A6
A1
Drive Strength
A0
DLL Enable
0
1
Mode Register
0
0
1
1
0
1
0
1
SSTL II-Weak Mode
SSTL II-Weak Mode
RFU
0
1
Enable
Disable
Extend. Mode Reg.
Matched Impedance 2.5V
Figure 4
3.3
Extended Mode Register Bitmap
Signal and Timing Description
General Description
3.3.1
The 128Mbit DDR SGRAM is a 16MByte Synchronous Graphics DRAM. It consists of four banks. Each bank is
organized as 4096 rows × 256 columns × 32 bits.
Read and Write accesses are burst oriented. Accesses begin with the registration of an Activate command, which
is then followed by a Read or Write command. The address bits registered coincident with the Activate command
are used to select the bank and the row to be accessed. BA1 and BA0 select the bank, address bits A11.. A0 select
the row. Address bits A7.. A0 registered coincident with the Read or Write command are used to select the starting
column location for the burst access.
The regular Single Data Rate SGRAM read and write cycles only use the rising edge of the external clock input.
For the DDR SGRAM, the special signals DQSx (Data Strobe) are used to mark the data valid window. During
Data Sheet
16
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
read bursts, the data valid window coincides with the high or low level of the DQSx signals. During write bursts,
the DQSx signal marks the center of the valid data window. Data is available at every rising and falling edge of
DQSx, therefore the data transfer rate is doubled.
For Read accesses, the DQSx signals are aligned to the clock signal CLK.
3.4
Special Signal Description
Clock Signal
3.4.1
The DDR SGRAM operates with a differential clock (CLK and CLK#) input. CLK is used to latch the address and
command signals. Data input and DMx signals are latched with DQSx. The DDR SGRAM implements a Delay
Locked Loop circuit (DLL) which tracks both edges of the CLK input signal and aligns the DQS output edges with
the CLK input edges.
The minimum and maximum clock cycle time is defined by tCK. The maximum value for tCK is defined to provide a
lower bound for the operation frequency of the internal DLL circuit. The minimum and maximum clock duty cycle
are specified using the minimum clock high time tCH and the minimum clock low time tCL respectively.
The internal DLL circuit requires additional 200 clock cycles after DLL reset for internal clock stabilization.
3.4.2
Command Inputs and Addresses
Like single data rate SGRAMs, each combination of RAS#, CAS# and WE# input in conjunction with CS# input at
a rising edge of the clock determines a DDR SGRAM command.
VIH
CLK, CLK#
VIL
tIS
VIH
VTT
VIL
Address,
CS#, RAS#,
CAS#, WE#,
CKE
Valid
Valid
tIH
Figure 5
3.4.3
Command and Address Signal Timing
Data Strobe and Data Mask
Operation at Burst Reads
3.4.3.1
The Data Strobes provide a 3-state output signal to the receiver circuits of the controller during a read burst. The
data strobe signal goes tRPRE clock cycle low before data is driven by the DDR SGRAM and then toggles low to
high and high to low till the end of the burst. The CAS latency is specified to the first low to high transition. The
edges of the Output Data signals and the edges of the data strobe signals during a read are nominally coincident
with edges of the input clock. The tolerance of these edges is specified by the parameters tAC and tDQSCK and is
referenced to the crossing point of the CLK and CLK# signal. The tDQSQ timing parameter describes the skew
between the data strobe edge and the output data edge.
The following table summarizes the mapping of DQSx and DMx signals to the data bus.
Data Sheet
17
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
Table 4
Mapping of DQSx and DMx
data strobe signal
data mask signal
Controlled data bus
DQS0
DQS1
DQS2
DQS3
DM0
DM1
DM2
DM3
DQ7 .. DQ0
DQ8 .. DQ15
DQ16 .. DQ23
DQ24 .. DQ31
The minimum time during which the output data is valid is critical for the receiving device. This also applies to the
Data Strobe DQS during a read since it is tightly coupled to the output data. The parameters tQH and tDQSQ define
the minimum output data valid window.
Prior to a burst of read data, given that the device is not currently in burst read mode, the data strobe signals transit
from Hi-Z to a valid logic low. This is referred to as the data strobe “read preamble” tRPRE
.
Once the burst of read data is concluded, given that no subsequent burst read operation is initiated, the data strobe
signals transit from a valid logic low to Hi-Z. This is referred to as the data strobe “read postamble” tRPST
.
T0
T1
T2
T3
T4
tCH
tCL
tCK
tHP
VIH
CLK,
VIL
CLK#
tDQSCK
"Preamble"
tRPRE
"Postamble"
tRPST
VIH
VTT
VIL
DQS
DQx
tAC
VIH
VTT
VIL
D
D+1
D+2
D+3
tQH
tDQSQ
tQHS
Figure 6
DQS Timing for Read
3.4.3.2
Operation at Burst Write
During a write burst, control of the data strobe is driven by the memory controller. The DQSx signals are nominally
centered with respect to data and data mask. The tolerance of the data and data mask edges versus the data
strobe edges during writes are specified by the setup and hold time parameters of data (tQDQSS & tQDQSH) and data
mask (tDMDQSS & tDMDQSH). The input data is masked in the same cycle when the corresponding DMx signal is high
(i.e. the DMx mask to write latency is zero.)
Data Sheet
18
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
VIH
VTT
VIL
DQSx
tDMDQSS
tDMDQSS
VIH
VTT
VIL
DMx
DQx
tDMDQSH
tDMDQSH
tQDQSH
tQDQSH
VIH
VTT
VIL
Q
Q+1
Q+2
tQDQSS
Q+3
Q+4
tQDQSS
Input Data masked
Figure 7
DQS and DM Timing at Write
Prior to a burst of write data, given that the controller is not currently in burst write mode, the data strobe signal
(DQSx) transits from Hi-Z to a valid logic low. This is referred to as the data strobe “Write Preamble”. Once the
burst of write data is concluded, given that no subsequent burst write operation is initiated, the data strobe signal
(DQSx) transits from a valid logic low to Hi-Z. This is referred to as the data strobe “Write Postamble”, tWPST. For
DDR SGRAM, data is written with a delay which is defined by the parameter tDQSS (DDR write latency). This is
different than the single data rate SGRAM where data is written in the same cycle as the Write command is issued.
VIH
CLK,
CLK#
VIL
WR
tDQSS
tWPST
tWPREH
VIH
VTT
VIL
DQSx
DQx
"Preamble"
tWPRES
"Postamble"
VIH
VTT
VIL
Q
Q+1
Q+2
Q+3
Figure 8
DQS Pre/Postamble at Write
Data Sheet
19
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
3.5
Description of Timings
Power-Up Sequence
3.5.1
The following sequence is highly recommended for Power-Up:
1. Apply power and start clock. Maintain CKE=L and the other pins are in NOP conditions at the input
2. Apply VDD before or at the same time as VDDQ, apply VDDQ before or at the same time as VREF & VTT
3. Start clock, maintain stable conditions for 200 µs min.
4. Apply NOP and set CKE to high
5. Apply a Precharge All command
6. Issue EMRS (extended mode register set) command to enable the DLL
7. Issue a Mode Register Set command for “DLL reset“. 200 cycles of clock input are required to lock the DLL.
8. Issue Precharge commands for all banks of the device.
9. Issue two or more Auto-Refresh commands.
10. Issue a Mode Register Set command. (This step may also be taken as step 6)
Clock
any
DLL
PREA
EMRS
PREA
ARef
ARef
MRS
Command
NOP
Reset
Comm.
t
t
t
t
t
t
MRD
2 Clock
min.
RP
MRD
RP
RFC
RFC
200 Clock min.
Figure 9
Power-Up Sequence
3.5.2
Mode Register Set Timing
The DDR SGRAM should be activated with CKE already high prior to writing into the mode register. Two clock
cycles are required to complete the write operation in the mode register. The mode register contents can be
changed using the same command and clock cycle requirements during operation as long as all banks are in the
idle state.
Clk
any
Comm.
PREA
NOP
MRS
NOP
NOP
NOP
Command
t
t
MRD
RP
Figure 10 Mode Register Set Timing
3.5.3
Extended Mode Register Set Timing
The timing of the Extended Mode Register Setup operation is equivalent to the Mode Register Setup timing.
Data Sheet
20
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
3.5.4
Bank Activation Command (ACT)
The Bank Activation command is initiated by issuing an ACT command at the rising edge of the clock. The DDR
SGRAM has four independent banks which are selected by the two Bank select Addresses (BA0, BA1). The Bank
Activation command must be applied before any Read or Write operation can be executed. The delay from the
Bank Activation command to the first read or write command must meet or exceed the minimum of RAS to CAS
delay time (tRCDDC min. for read commands and tRCDWR min. for write commands). Once a bank has been activated,
it must be precharged before another Bank Activate command can be applied to the same bank. The minimum
time interval between interleaved Bank Activate commands (Bank A to Bank B and vice versa) is the Bank to Bank
activation delay time (tRRD min).
Clk
READ
ACT
t
or
Command
Addresses
PRE
NOP
ACT
WRITE
RCDRD for read
t
RCDWR for write
Bank A
Bank A
Bank A
Bank A
Row Add.
Col. Add.
Row Add.
t
RC
Figure 11 Activate to Read or Write Command Timing (one bank)
Clk
ACT
Command
NOP
ACT
Bank B
Bank A
Addresses
Row Add.
Row Add.
t
RRD
Figure 12 Activate Bank A to Activate Bank B Timing
3.5.5
Precharge Command
This command is used to precharge or close a bank that has been activated. Precharge is initiated by issuing a
Precharge command at the rising edge of the clock. The Precharge command can be used to precharge each
bank respectively or all banks simultaneously. The Bank addresses BA0 and BA1 select the bank to be
precharged. After a Precharge command, the analog delay tRP has to be met until a new Activate command can
be initiated to the same bank.
Data Sheet
21
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
Table 5
A8/AP
Precharge Control
BA1
BA0
Precharged
0
0
0
0
1
0
0
1
1
X
0
1
0
1
X
Bank A Only
Bank B Only
Bank C Only
Bank D Only
All Banks
Clk
ACT
NOP
PRE
NOP
ACT
Command
Bank A
Bank A
Bank A
Addresses
Row Add
Row Add
tRAS
tRP
tRC
Figure 13 Precharge Command Timing
3.5.6
Self Refresh
The self refresh mode can be used to retain the data in the DDR SGRAM if the chip is powered down. To set the
DDR SGRAM into a self refreshing mode, a Self Refresh command must be issued and CKE held low at the rising
edge of the clock. Once the self Refresh command is initiated, CKE must stay low to keep the device in Self
Refresh mode. During the Self refresh mode, all of the external control signals are disabled except CKE. The clock
is internally disabled during Self Refresh operation to reduce power. An internal timing generator guarantees the
self refreshing of the memory content. To exit the Self Refresh mode, a stable external clock is needed for the DLL
before returning CKE high. After the Power Down Exit time(tPDEX), a Deselect or NOP command is issued and CKE
is held high for longer than tSREX in order to lock the DLL.
Data Sheet
22
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
Clk
SELF
NOP
NOP
NOP
NOP
Any
NOP
Command
CKE
REFRESH
DESEL
DESEL
DESEL
DESEL
Comm.
t
SREX
Figure 14 Self Refresh timing
3.5.7
Auto Refresh
The auto refresh function is initiated by issuing an Auto Refresh command at the rising edge of the clock. All banks
must be precharged and idle before the Auto Refresh command is applied. No control of the external address pins
is required once this cycle has started. All necessary addresses are generated in the device itself. When the
refresh cycle has completed, all banks will be in the idle state. A delay between the Auto Refresh command and
the next Activate Command or subsequent Auto Refresh Command must be greater than or equal to the tRFC(min).
Clk
PRE-
AUTO
NOP
Command
NOP
Command
CKE
CHARGE
REFRESH
Command is
AUTOREFRESH
or ACT
t
t
RFC
RP
Figure 15 Autorefresh timing
3.5.8
Power Down Mode
The Power Down Mode is entered when CKE is set low and exited when CKE is set high. The CKE signal is
sampled at the rising edge of the clock. Once the Power Down Mode is initiated, all of the receiver circuits except
CLK, CKE and DLL circuits are gated off to reduce power consumption. All banks can be set to idle state or stay
activate during Power Down Mode, but burst activity may not be performed. After exiting from Power Down Mode,
at least one clock cycle of command delay must be inserted before starting a new command. During Power Down
Mode, refresh operations cannot be performed; therefore, the device cannot remain in Power Down Mode longer
than the refresh period (tREF) of the device.
Data Sheet
23
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
Clk
NOP
Any
NOP
PRE
NOP
NOP
Command
CKE
DESEL
Command
DESEL
Power Down
Mode entry
Power Down
Mode exit
t
PDEX
Figure 16 Power Down Mode timing
3.5.9
Burst Mode Operation
Burst mode operation is used to provide a constant flow of data to the memory (write cycle) or from the memory
(read cycle). The burst length is programmable and set by address bits A0 - A3 during the Mode Register Setup
command. The burst length controls the number of words that will be output after a read command or the number
of words to be input after a write command. One word is 32 bits wide. The sequential burst length can be set to 2,
4 or 8 data words.
Table 6
Burst Mode and Sequence
Burst Length
Starting Column Address
Order of Access within a Burst
Type = Sequential
0 - 1
A2
A1
A0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
2
4
1 - 0
0
0
1
1
0
0
1
1
0
0
1
1
0 - 1 - 2 - 3
1 - 2 - 3 - 0
2 - 3 - 0 - 1
3 - 0 - 1 - 2
8
0
0
0
0
1
1
1
1
0 - 1 - 2 - 3 - 4 - 5 - 6 - 7
1 - 2 - 3 - 4 - 5 - 6 - 7 - 0
2 - 3 - 4 - 5 - 6 - 7 - 0 - 1
3 - 4 - 5 - 6 - 7 - 0 - 1 - 2
4 - 5 - 6 - 7 - 0 - 1 - 2 - 3
5 - 6 - 7 - 0 - 1 - 2 - 3 - 4
6 - 7 - 0 - 1 - 2 - 3 - 4 - 5
7 - 0 - 1 - 2 - 3 - 4 - 5 - 6
3.5.10
Burst Read Operation: (READ)
The Burst Read operation is initiated by issuing a READ command at the rising edge of the clock after tRCD from
the bank activation. The address inputs (A7.. A0) determine the starting address for the burst. The burst length (2,
4 or 8) must be defined in the Mode Register. The first data after the READ command is available depending on
the CAS latency. The subsequent data is clocked out on the rising and falling edge of DQSx until the burst is
completed. The DQSx signal is generated by the DDR SGRAM during Burst Read Operations.
Data Sheet
24
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
CLK
Read
NOP
NOP
NOP
NOP
NOP
NOP
NOP
Command
CL = 2
Read
Postamble
Read
DQSx
Preamble
CAS latency = 2
DQx
D-out D-out
D-out D-out
2
3
0
1
Burst length = 4
CL = 3
Read
Postamble
Read
Preamble
DQSx
CAS latency = 3
DQx
D-out D-out
D-out D-out
2
3
0
1
CL = 4
Read
Postamble
Read
Preamble
DQSx
CAS latency = 4
DQx
D-out D-out
D-out D-out
2
3
0
1
Figure 17 Burst Read Operation
3.5.11
Burst Write Operation (WRITE)
The Burst Write is initiated by issuing a WRITE command at the rising edge of the clock. The address inputs (A7..
A0) determine the starting column address. Data for the first burst write cycle must be applied on the DQ pins on
the first rising edge of DQSx following the WRITE command. The time between the WRITE command and the first
corresponding edge of the data strobe is tDQSS. The remaining data inputs must be supplied on each subsequent
rising and falling edge of the data strobe until the burst length is completed. When the burst has been finished,
any additional data supplied to the DQ pins will be ignored.
Data Sheet
25
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
CLK
WRITE
NOP
NOP
NOP
tDQSS
tWPST
DQSx
DQx
tWPRES
tWPREH
Data-in
0
Data-in
1
Data-in
2
Data-in
3
Burst length = 4
Figure 18 Burst Write Operation
3.5.12
Burst Stop Command (BST)
A Burst Stop is initiated by issuing a BURST STOP command at the rising edge of the clock. The Burst Stop
Command has the fewest restrictions, making it the easiest method to terminate a burst operation before it has
been completed. When the Burst Stop Command is issued during a burst read cycle, read data and DQSx go to
a high impedance state after a delay which is equal to the CAS Latency set in the Mode Register. The Burst Stop
latency is equal to the CAS latency CL.The Burst Stop command is not supported during a write burst operation.
Burst Stop is also illegal during Read with Auto-Precharge.
Data Sheet
26
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
CLK
READ
BST
NOP
NOP
NOP
NOP
NOP
NOP
Command
CL = 2
Burst Stop Latency = 2
DQSx
CAS latency = 2
DQx
D-out D-out
0
1
CL = 3
Burst Stop Latency = 3
DQSx
CAS latency = 3
DQx
D-out D-out
0
1
Burst Stop Latency = 4
DQSx
CAS latency = 4
DQx
D-out D-out
0
1
Burst length = 4
Figure 19 Burst Stop for Read
3.5.13
Data Mask (DMx) Function
The DDR SGRAM has a Data Mask function that can be used only during write cycles. When the Data Mask is
activated (DMx high) during burst write, the write operation is masked immediately. The DMx to data-mask latency
is zero. DMx can be issued at the rising or falling edge of Data Strobe.
Data Sheet
27
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
CLK
WRITE
NOP
NOP
NOP
NOP
NOP
NOP
NOP
Command
DQSx
DQx
D-in
D-in
D-in
3
D-in
D-in
5
D-in
D-in
1
D-in
7
0
2
4
6
DMx
Burst length = 8
Data is masked out
Figure 20 Data Mask Timing
3.5.14
Autoprecharge Operation
The Autoprecharge command is issued by setting column address A8 high when a Read or a Write command is
asserted to the DDR SGRAM. If A8 is low when Read or Write command is issued, a normal Read or Write burst
operation is executed and the bank remains active at the end of the burst sequence. When the Auto Precharge
command is activated, the active bank automatically begins to precharge at the earliest possible moment during
the Read or Write cycle after tRAS(min.) is satisfied.
3.5.15
Read with Autoprecharge (READA)
If a Read with Auto-precharge command is initiated, the DDR SGRAM automatically enters the precharge
operation BL/2 clock cycles after the READA command and tRAS(min.) is satisfied. If tRAS(min.) has not been satisfied
yet, an internal interlock will delay the precharge operation until it is satisfied. Once the precharge operation has
started, the bank cannot be reactivated and the new command can not be asserted until the Precharge time (tRP)
has been satisfied.
Data Sheet
28
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
CLK
READA
NOP
NOP
NOP
NOP
NOP
NOP
ACT
Command
CL = 2
DQSx
CAS latency = 2
DQx
D-out D-out
D-out D-out
2
3
0
1
CL = 3
DQSx
CAS latency = 3
DQx
D-out D-out
D-out D-out
2
3
0
1
CL = 4
DQSx
CAS latency = 4
DQx
D-out D-out
D-out D-out
2
3
0
1
t
RP
BL / 2
Begin of
Autoprecharge
Bank can be activated after
completion of precharge
Burst length = 4
Figure 21 Read Burst with Autoprecharge
Data Sheet
29
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
Burst length = 4
CAS latency = 3
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
BANK A
READ A
+ AP
NOP
NOP
NOP
NOP
NOP
NOP
NOP
Command
ACTIVATE
t RCD(min)
t RAS(min)
t RP
Begin of
Auto Precharge
BL / 2
DQSx
DQx
CL = 3
D-out
D-out D-out
D-out
0
2
3
1
Figure 22 Read Concurrent Auto Precharge
Table 7
Concurrent Read Auto Precharge Support
For same Bank
Asserted
For different Bank
Command
T4
T5
T6
T4
T5
T6
READ
NO
YES
NO
NO
YES
NO
YES
NO
NO
NO
NO
NO
NO
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
READ+AP
ACTIVATE
PRECHARGE YES
Note:This table is for the case of Burst Length = 4, CAS Latency =3 and tWR=2 clocks
When READ with Auto Precharge is asserted, new commands can be asserted at T4,T5 and T6 as shown in
Table 7.
An Interrupt of a running READ burst with Auto Precharge i.e. at T4 and T5 to the same bank with another
READ+AP command is allowed, it will extend the begin of the internal Precharge operation to the last READ+AP
command.
Interrupts of a running READ burst with Auto Precharge i.e. at T4 are not allowed when doing concurrent
command to another active bank. ACTIVATE or PRECHARGE commands to another bank are always possible
while a READ with Auto Precharge operation is in progress.
3.5.16
Write with Autoprecharge (WRITEA)
If A8 is high when a Write command is issued, the Write with Auto-Precharge function is performed. The internal
precharge begins after the write recovery time tWR and tRAS(min.) are satisfied.
If a Write with Auto Precharge command is initiated, the DDR SGRAM automatically enters the precharge
operation at the first rising edge of CLK after the last valid edge of DQS (completion of the burst) plus the write
recovery time tWR. Once the precharge operation has started, the bank cannot be reactivated and the new
command can not be asserted until the Precharge time (tRP) has been satisfied. If tRAS(min.) has not been satisfied
yet, an internal interlock will delay the precharge operation until it is satisfied.
Data Sheet
30
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
Burst length = 4
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
BANK A
WRITE A
+ AP
NOP
NOP
NOP
NOP
NOP
NOP
NOP
Command
ACTIVATE
t RAS(min)
t WR
t RP
BL / 2
Begin of
Auto Precharge
DQSx
DQx
D-in
0
D-in
2
D-in
3
D-in
1
Figure 23 Write Burst with Auto Precharge
Note:tWR starts at the first rising edge of clock after the last valid edge of the 4 DQSx.
Table 8
Concurrent Write Auto Precharge Support
For same Bank
Asserted
For different Bank
Command
T3
T4
T5
T6
T7
T8
T3
T4
T5
T6
T7
WRITE
NO
YES
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
YES
YES
YES
YES
NO
YES
YES
NO
YES
YES
NO
YES
YES
YES
YES
YES
YES
WRITE+AP
READ
READ+AP
ACTIVATE
NO
NO
NO
YES
YES
YES
YES
YES
YES
PRECHARGE NO
When Write with Auto Precharge is asserted, new commands can be asserted at T3.. T8 as shown in Table 8.
An Interrupt of a running WRITE burst with Auto Precharge i.e. at T3 to the same bank with another WRITE+AP
command is allowed as long as the burst is running, it will extend the begin of the internal Precharge operation to
the last WRITE+AP command.
Interrupts of a running WRITE burst with Auto Precharge i.e. at T3 are not allowed when doing concurrent
WRITE’s to another active bank. Consecutive WRITE or WRITE+AP bursts (T4.. T7) to other open banks are
possible. ACTIVATE or PRECHARGE commands to another bank are always possible while a WRITE with Auto
Precharge operation is in progress.
3.6
Burst Interruption
3.6.1
Read Interrupted by a Read
A Burst Read can be interrupted before completion of the burst by a new Read command given to any bank. When
the previous burst is interrupted, the remaining addresses are overridden by the new address with the full burst
length. The data from the first Read command continues to appear on the outputs until the CAS latency from the
Data Sheet
31
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
interrupting Read command is satisfied. At this point, the data from the interrupting Read command appears. Read
to Read interval (CAS#(a) to CAS#(b) Command period, tCCD) is minimum 1 CLK.
CLK
READ a
READ b
NOP
NOP
NOP
NOP
Command
t
CCD
DQSx
DQx
D-out
b0
D-out D-out
a0 a1
D-out D-out
D-out
b3
b1
b2
Burst length = 4
CL = 2
Figure 24 Read interrupted by Read
3.6.2
Read Interrupted by a Write
To interrupt a burst read with a write command, a Burst Stop command must be asserted to avoid data contention
on the I/O bus by placing the DQ's (Output drivers) in a high impedance state at least one clock cycle before the
Write Command is initiated (Last Output to Write Command Latency). To insure that the DQs are tri-stated one
cycle before the write operation begins, the Burst Stop command must be applied at least 3 clock cycles for CL =
2, at least 4 clock cycles for CL = 3 or at least 5 clock cycles for CL = 4 before the Write command.
CLK
READ
BST
NOP
NOP
WRITE
NOP
NOP
NOP
Command
Burst Stop latency = CL
DQSx
DQx
D-out D-out
D-in
0
D-in
1
D-in
2
D-in
3
0
1
Burst Stop to Write command latency
Burst length = 4
CL = 2
Figure 25 Read interrupted by Write
Data Sheet
32
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
3.6.3
Read Interrupted by a Precharge
A Burst Read operation can be interrupted by a Precharge of the same bank. The Read command to Precharge
time is minimum 1 clock cycle. The Precharge command disables the data output depending on the CAS latency.
Once the last data bit has been outputted, the output buffers are tristated. A new Bank Activate command may be
issued to the same bank after tRP.
CLK
READ
NOP
PRE
NOP
NOP
ACT
NOP
Command
Precharge latency = CL
First possible
ACT command
DQSx
DQx
D-out D-out D-out D-out
0
1
2
3
Burst length = 8
CL = 2
t
RP
Figure 26 Read interrupted by Precharge
3.6.4
Write Interrupted by a Write
A Burst Write can be interrupted before completion of the burst by a new Write Command. The minimum distance
between two different Write commands is one clock cycle. When the previous burst is interrupted, the remaining
addresses are overridden by the new address and data will be written into the device until the programmed burst
length is satisfied. The Write to Write interval (CAS a to CAS b command period) is defined by the parameter tCCD
.
CLK
WRITE a
WRITE b
NOP
NOP
NOP
Command
t
CCD
DQSx
DQx
D-in
b0
D-in
a0
D-in
a1
D-in
b1
D-in
b2
D-in
b3
Burst length = 4
Figure 27 Write interrupted by Write
Data Sheet
33
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
3.6.5
Write Interrupted by a Read
A Burst Write can be interrupted by a Read command sent to any bank. The DQs must be in the high impedance
state at least one clock cycle before the data of the interrupting read appears on the outputs to avoid data
contention. Before the Read Command is registered, any residual data from the burst write cycle must be masked
by DMx. Data that is presented on the DQ pins before the Read command is initiated, will actually be written to
the memory.
CLK
Write
NOP
NOP
Read
NOP
NOP
NOP
Command
tDQSS
Last valid
data
tWTR
CL = 2
DQSx
DQx
D-in
D-in
1
D-in
D-in
D-in
D-in
5
D-out D-out
0
2
3
4
0
1
DMx
Data must be
masked
Data is masked
by Read
Burst length = 8
CL = 2
Figure 28 Write interrupted by Read
3.6.6
Write Interrupted by a Precharge
A Burst Write operation can be interrupted before completion of the burst by a Precharge of the same bank.
Random column access is allowed. A Write Recovery time (tWR) is required from the last data to Precharge
command. When Precharge command is asserted, any residual data from the burst write cycle must be masked
by DMx.
Data Sheet
34
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
CLK
Write
Write
NOP
NOP
NOP
tWR
PRE
NOP
NOP
Command
bank A
bank B
tDQSS
Last valid
data
tDQSS
DQSx
DQx
D-in
D-in
1
D-in
D-in
3
D-in
D-in
5
D-in
D-in
1
0
2
4
0
DMx
Data must be
masked
Data is masked
by Precharge
Burst length = 8
Figure 29 Write interrupted by Precharge
3.7
Operations and Functions
Table 9
Command Overview
Operation
Code
CKE CKE CS# RAS# CAS# WE# BA0 BA1 A8
A0-7
n-1
n
X
X
X
X
A9-11
Device Deselect
No Operation
DESEL
NOP
H
H
L
L
L
X
H
L
X
H
L
X
H
L
X
X
0
X
X
0
X
X
X
X
H
Mode Register Setup
MRS
H
OPCODE
OPCODE
Extended Mode Register MRS
Setup
H
L
L
L
1
0
Bank Activate
Read
ACT
H
H
H
X
X
X
L
L
L
L
L
H
H
L
H
H
H
BA
BA
BA
BA
BA
BA
Row Address
READ
READA
L
Col.
Col.
Read with Auto
Precharge
H
H
Write Command
WRITE
H
H
X
X
L
L
L
H
L
H
H
BA
BA
BA
BA
L
Col.
Col.
Write Command with
Auto Precharge
WRITEA
H
H
Burst Stop
BST
H
H
H
H
H
X
X
X
H
L
L
L
L
L
L
H
L
L
L
L
H
H
H
L
L
X
X
X
L
X
X
X
X
X
Precharge Single Bank PRE
L
BA
X
BA
X
Precharge All Banks
Auto Refresh
PREAL
L
H
X
X
AREF
H
H
X
X
Self Refresh Entry
Self Refresh Exit
SREFEN
SREFEX
L
X
X
L
L
H
H
H
L
X
H
X
H
X
H
X
X
X
X
X
X
X
X
Data Sheet
35
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
Table 9
Command Overview (cont’d)
Code CKE CKE CS# RAS# CAS# WE# BA0 BA1 A8
Operation
A0-7
n-1
n
A9-11
Power Down Mode Entry PWDNEN
(Note)
H
H
L
L
H
L
X
H
X
H
X
H
X
X
X
X
X
X
X
X
Power Down Mode Exit PWDNEX
L
H
H
L
X
X
X
X
X
X
X
valid valid valid
Note:The Power Down Mode Entry command is illegal during Burst Read or Burst Write operations.
3.8
Function Truth Tables
Table 10 lists all abbreviations used in Table 11 and Table 12.
Table 10
Abbreviations
High Level
H
L
Low Level
X
Don’t Care
V
Valid Data Input
Row Address
Bank Address
Precharge All
No Operation
Column Address
Address Line x
RA
BA
PA
NOP
CA
Ax
Table 11
Function Truth Table I
Current State Command
Address
X
Action
Notes
3)1)3)
IDLE
DESEL
NOP
NOP
X
NOP
3)2)3)
3)
BST
X
NOP
READ / READA
WRITE / WRITEA
ACT
BA,CA,A8
BA,CA,A8
BA, RA
BA, A8
X
ILLEGAL
1)4)1)
1)1)
ILLEGAL
Bank Active
PRE / PREAL
AREF / SREF
MRS / EMRS
NOP
AUTO-Refresh or Self-Refresh
4)5)4)
Op-Code
Mode Register Set or Extended Mode
Register Set
Data Sheet
36
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
Table 11
Function Truth Table I (cont’d)
Current State Command
Address
Action
NOP
Notes
ROW ACTIVE DESEL
X
NOP
BST
X
NOP
X
NOP
READ / READA
BA, CA, A8
Begin Read, Determine Auto Precharge 9)6)9)
WRITE / WRITEA
ACT
BA, CA, A8
Begin Write, Determine Auto Precharge
ILLEGAL
9)9)
1), 5)1), 5)
6)7)6)
BA, RA
PRE / PREAL
AREF / SREF
MRS / EMRS
DESEL
BA, A8
Precharge / Precharge All
ILLEGAL
X
OP-Code
ILLEGAL
READ
X
Continue burst to end
Continue burst to end
Terminate Burst
NOP
X
BST
X
READ / READA
BA, CA, A8
Terminate burst, Begin New Read,
Determine Auto-Prechgarge
7)8)7)
WRITE / WRITEA
ACT
BA, CA, A8
ILLEGAL
2), 7)9)2), 7)
1)1)
BA, RA
ILLEGAL
PRE / PREAL
AREF / SREF
MRS / EMRS
DESEL
BA ,A8
Terminate Burst / Precharge
ILLEGAL
X
Op-Code
ILLEGAL
READ with
Auto Precharge
X
Continue burst to end, Precharge
Continue burst to end, Precharge
ILLEGAL
NOP
X
BST
BA
READ / READA
WRITE / WRITEA
ACT
BA, CA, A8
ILLEGAL
BA, CA, A8
ILLEGAL
BA, RA
ILLEGAL
1)1)
1)1)
PRE / PREAL
AREF / SREF
MRS / EMRS
DESEL
BA ,A8
ILLEGAL
X
ILLEGAL
Op-Code
ILLEGAL
WRITE
X
Continue burst to end
Continue burst to end
ILLEGAL
NOP
X
BST
X
READ / READA
BA, CA, A8
Terminate Burst, Begin Read, Determine 7), 8)7), 8)
Auto-Precharge.
WRITE / WRITEA
BA, CA, A8
Terminate Burst, Begin new Write,
Determine Auto-Precharge
2), 7)2), 7)
ACT
BA, RA
BA ,A8
X
ILLEGAL
1)1)
8)8)
PRE / PREAL
AREF / SREF
MRS / EMRS
Terminate Burst , Precharge
ILLEGAL
OP-Code
ILLEGAL
Data Sheet
37
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
Table 11
Function Truth Table I (cont’d)
Current State Command
Address
Action
Notes
WRITE with
DESEL
X
Continue burst to end, Precharge
Autoprecharge
NOP
X
Continue burst to end, Precharge
BST
X
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
READ / READA
WRITE / WRITEA
ACT
BA, CA, A8
BA, CA, A8
BA, RA
1)1)
1)1)
PRE / PREAL
AREF / SREF
MRS / EMRS
DESEL
BA ,A8
X
OP-Code
ROW
ACTIVATING
X
NOP ( Row Active after tRCD
NOP ( Row Active after tRCD
NOP ( Row Active after tRCD
ILLEGAL
)
)
)
NOP
X
BST
X
READ / READA
WRITE / WRITEA
ACT
BA, CA, A8
BA, CA, A8
BA, RA
BA ,A8
X
1), 9)1), 9)
1), 9)1), 9)
1), 5)1), 5)
1), 6)1), 6)
ILLEGAL
ILLEGAL
PRE / PREAL
AREF / SREF
MRS / EMRS
ILLEGAL
ILLEGAL
OP-Code
X
ILLEGAL
PRECHARGE DESEL
NOP ( Row Idle after tRP)
NOP ( Row Idle after tRP)
NOP ( Row Idle after tRP)
ILLEGAL
NOP
BST
X
X
READ / READA
BA, CA, A8
BA, CA, A8
BA, RA
BA ,A8
X
1)1)
1)1)
1)1)
1)1)
WRITE / WRITEA
ACT
ILLEGAL
ILLEGAL
PRE / PREAL
AREF / SREF
MRS / EMRS
DESEL
NOP ( Row Idle after tRP)
ILLEGAL
OP-Code
X
ILLEGAL
WRITE
RECOVERING
NOP (Row Active after tWR
NOP (Row Active after tWR
NOP (Row Active after tWR
)
)
)
NOP
X
BST
X
READ / READA
WRITE / WRITEA
ACT
BA, CA, A8
BA, CA, A8
BA, RA
BA ,A8
X
Begin Read, Determine Auto-Prechgarge 2)2)
Begin Write, Determine Auto-Prechgarge
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
2)2)
1),10)
PRE / PREAL
AREF / SREF
MRS / EMRS
OP-Code
Data Sheet
38
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
Table 11
Function Truth Table I (cont’d)
Current State Command
Address
Action
Notes
WRITE
DESEL
X
NOP (Precharge after tWR
NOP (Precharge after tWR
NOP (Precharge after tWR
ILLEGAL
)
)
)
RECOVERING
with Auto-
precharge
NOP
X
BST
X
1), 2)
1)
READ / READA
WRITE / WRITEA
ACT
BA, CA, A8
BA, CA, A8
BA, RA
BA ,A8
X
ILLEGAL
1)
ILLEGAL
1)
PRE / PREAL
AREF / SREF
MRS / EMRS
DESEL
ILLEGAL
ILLEGAL
OP-Code
X
ILLEGAL
REFRESH
NOP (Idle after tRC)
NOP (Idle after tRC)
NOP (Idle after tRC)
ILLEGAL
NOP
X
BST
X
READ / READA
WRITE / WRITEA
ACT
BA, CA, A8
BA, CA, A8
BA, RA
BA ,A8
X
ILLEGAL
11)
ILLEGAL
PRE / PREAL
AREF / SREF
MRS / EMRS
DESEL
ILLEGAL
ILLEGAL
OP-Code
X
ILLEGAL
(EXTENDED
MODE
NOP (Idle after two clocks)
REGISTER
SET)
NOP
X
NOP (Idle after two clocks)
NOP (Idle after two clocks)
ILLEGAL
BST
X
READ / READA
WRITE / WRITEA
ACT
BA, CA, A8
BA, CA, A8
BA, RA
BA ,A8
X
ILLEGAL
ILLEGAL
PRE / PREAL
AREF / SREF
MRS / EMRS
ILLEGAL
ILLEGAL
OP-Code
ILLEGAL
1) Illegal to bank specified states; function may be legal in the bank indicated by BAx, depending on the state of that bank
2) Must satisfy bus contention, bus turn around, write recovery requirements.
3) If both banks are idle, and CKE is inactive, the device will enter Power Down Mode. All input buffers except CKE, CLK and
CLK# will be disabled.
4) If both banks are idle, and CKE is deactivated coincidentally with an AutoRefresh command, the device will enter
SelfRefresh Mode. All input buffers except CKE will be disabled.
5) Illegal, if tRRD is not satisfied.
6) Illegal, if tRAS is not satisfied.
7) Must satisfy burst interrupt condition.
8) Must mask two preceding data bits with the DM pin.
9) Illegal, if tRCD is not satisfied.
10) Illegal, if tWR is not satisfied.
11) Illegal, if tRC is not satisfied.
Note:All entries assume the CKE was High during the preceding clock cycle
Data Sheet
39
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
Table 12
Function Truth Table for CKE
CKE CKE CS# RAS CAS WE# Address Action
Current
State
Notes
n-1
H
L
n
X
H
H
H
H
H
L
#
#
1)
1)
1)
1)
1)
1)
1)
SELF
REFRESH
X
H
L
X
X
H
H
H
L
X
X
H
H
H
L
X
X
H
X
X
X
X
X
X
X
X
H
X
H
L
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
INVALID
Exit Self-Refresh ( Idle after tSRX
Exit Self-Refresh ( Idle after tSRX
ILLEGAL
)
)
L
L
L
L
L
ILLEGAL
L
L
ILLEGAL
L
X
X
X
X
X
L
X
X
X
X
X
L
X
X
X
X
X
L
NOP ( Maintain Self Refresh)
INVALID
POWER
DOWN
H
L
X
H
L
Exit Power Down ( Idle after tPDEX
NOP ( Maintain Power Down)
Refer to Function Truth Table
Enter Self Refresh
Enter Power-Down
Enter Power-Down
ILLEGAL
)
L
2)
3)
2)
2)
2)
2)
2)
ALL
BANKS
IDLE
H
H
H
H
H
H
H
L
H
L
L
H
L
X
H
H
H
L
X
H
H
L
L
L
L
L
L
X
X
X
X
ILLEGAL
L
L
X
X
X
ILLEGAL
X
H
X
X
X
X
Refer to Power Down in this table
Refer to Funtion Truth Table
All other
states
H
1) CKE low-to-high transition re-enables inputs asynchronously. A minimum setup time to CLK must be satisfied before any
commands other than EXIT are executed.
2) Power Down can be entered when all banks are idle (banks can be active or precharged)
3) Self Refresh can be entered only from the Precharge / Idle state.
Data Sheet
40
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Register Set
3.9
DDR SGRAM Simplified State Diagram
SELF
REFRESH
SREFEN
SREFEX
MODE
REGISTER
SET
MRS
AUTO
REFRESH
AREF
IDLE
CKEL
CKEH
ACT
POWER
CKEH
DOWN
CKEL
ROW
ACTIVE
WRITE
BST
READ
WRITEA
READA
WRITE
READ
READ
WRITEA
READA
READA
PRE
READA
WRITEA
PRE
PRE
PRE
POWER
ON
PRE
CHARGE
Automatic Sequence
Command Sequence
Figure 30 DDR SGRAM Simplified State Diagram
Data Sheet
41
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Electrical Characteristics
4
Electrical Characteristics
Table 13
Absolute Maximum Ratings
Symbol
Parameter
Values
typ.
–
Unit
Note/
Test Condition
min.
max.
Voltage on I/O pins relative to VSS
VIN, VOUT
–0.5
VDDQ
+
V
–
0.5
Voltage on Inputs relative to VSS
Voltage on VDD supply relative to VSS
Voltage on VDDQ supply relative to VSS
Operating Temperature (Ambient)
Storage Temperature (Plastic)
Power Dissipation
VIN
–0.5
–0.5
–0.5
0
–
+3.6
+3.6
+3.6
+70
+150
–
V
–
–
–
–
–
–
–
VDD
VDDQ
TA
–
V
–
V
–
° C
° C
W
mA
TSTG
PD
–55
–
–
1.4
50
Short Circuit Output Current
IOUT
–
–
Attention: Stresses above those listed here may cause permanent damage to the device. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Maximum ratings are absolute ratings; exceeding only one of these values may cause
irreversible damage to the integrated circuit.
Table 14
Power & DC Operation Conditions
Parameter
Symbol
Values
Unit Notes 1)
min.
2.38
2.38
2.5
typ. max.
2.5 2.63
2.5 2.63
Power Supply Voltage
VDD
VDD
VDD
VDD
VDDQ
VREF
V
V
V
V
V
V
L3.6, L4.52)
–3.6, –4.5, –5 2)
–3.6, L3.6 2)3)
–3, –3.3 2)
2) 4)
—
—
2.9
2.9
2.5
Power Supply Voltage for I/O Buffer
Reference Voltage
2.38
2.5 2.63
5) 6)
0.49 ×
VDDQ
1.25 0.51 ×
VDDQ
7)
Termination Voltage
VT
V
REF - 0.04 VREF
V
5
5
5
V
V
REF + 0.04 V
t
Input leakage current
IIL
–5
–5
–5
—
—
—
µA
—
—
CLK Input leakage current
Output leakage current
Input logic high voltage, DC
Input logic low voltage, DC
IILC
IOL
VIH
VIL
µA
µA
V
—
8)
V
V
REF + 0.15 —
DDQ + 0.3
REF - 0.15
9)
SSQ - 0.3
—
V
Output Levels: Matched Impedance Mode 2.5V
High Current at VOUT = VDDQ-0,373V
Low Current at VOUT = 0.373V
IOH
IOL
–5
5
—
—
—
—
mA
mA
—
—
Output Levels: SSTL2 Weak Mode 2.5V
High Current at VOUT = VDDQ – 0,373V
Low Current at VOUT = 0.373V
IOH
IOL
–5
5
—
—
—
—
mA
mA
—
—
Data Sheet
42
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Electrical Characteristics
1) TA = 0 to 70 °C; VSS = 0 V
2) Under all conditions, VDDQ must be less than or equal to VDD
3) The speed sorts L3.6 and –3.6 support both VDD modes: 2.5V ±5% and 2.5V – 2.9V
4) VDDQ = 2.5 V -/+5%
5) Typically the value of VREF is expected to be 0.5 * VDDQ of the transmitting device. VREF is expected to track variations in
VDDQ
6) Peak to peak AC noise on VREF may not exceed 2% VREF (DC)
7) VTT of the transmitting device must track VREF of the receiving device
8) Overshoots of VIH must be limited to a voltage < (VDDQ + 1.5 V) and a pulse width < 0.33 of the clock pulse
9) Undershoots of VIL must be limited to a voltage > -1.5 V and a pulse width < 0.33 of the clock pulse
Table 15
AC Operation Conditions
Parameter
Symbol
Values
Unit Notes
min.
typ. max.
Input logic high voltage
Input logic low voltage
VIH
V
V
V
V
V
V
1.2
1.0
1.2
1.0
REF + 0.50
—
—
—
—
—
—
—
—
—
—
VREF
—
—
V
V
V
V
V
V
V
V
V
V
V
DDQ + 0.3
DDQ + 0.3
DDQ + 0.3
REF - 0.50
REF - 0.60
REF - 0.50
DDQ + 0.6
DDQ + 0.6
DDQ + 0.6
DDQ + 0.6
REF + 0.2
V
V
V
V
V
V
V
V
V
V
V
V
L3.6, L4.5
REF + 0.60
REF + 0.50
SSQ - 0.3
SSQ - 0.3
SSQ - 0.3
–5.0
–3, –3.3, –3.6, –4.5
VIL
VID
L3.6, L4.5
–5.0
–3, –3.3, –3.6, –4.5
Clock Differential Input Voltage
(CLK/CLK)
L4.5
L3.6
–4.5, –5.0
–3, –3.3, –3.6, –4.5
Clock Input Crossing Point (CLK/CLK) VIX
I/O Reference Voltage
V
REF - 0.2
—
—
VREF
rI
0.49 × VDDQ
1.0
0.51 × VDDQ
—
Input Slew Rate
V/ns —
+ Vtt = 0.5xVDDQ
50 Ohm
Test point
15 pF
DQ, DQS
Figure 31 Output Test Circuit
Table 16
Pin
Pin Capacitances
min.
max.
2.5
Unit
pF
A11.. A0, BA1, BA0, CKE, CS, CAS, RAS, WE
CLK, CLK
1.0
1.0
2.5
pF
Data Sheet
43
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Electrical Characteristics
Table 16
Pin
Pin Capacitances
min.
1.0
max.
3.0
Unit
pF
DQ0.. DQ31, DQS0 .. DQS3
DM0.. DM3
1.0
3.0
pF
Table 17
Timing Parameters for speed sorts –3, –3.3, –3.6, –4.5, and –5
Part Number Extension
Interface
–3
–3.3
MIM
–3.6
MIM
–4.5
–5
WM/MIM
Unit Note1)
2)
MIM
WM/MIM
—
Parameter
Symbol min. max. min. max. min. max. min. max. min. max. —
—
Clock and Clock Enable
Clock Cycle Time
System frequency
tCK
tCK
fCK
fCK
tCH
3.0 5.0
4.0 5.0
3.3 5.0
4.0 5.0
3.6
4.2
5.0
5.0
4.5 5.5
4.5 5.5
183 222
183 222
5.0 5.5
5.0 5.5
ns
ns
CL = 4
CL = 3
200 333 200 300 200 278
200 250 200 250 200 238
183 200 MHz CL = 4
183 200 MHz CL = 3
Clock high level
width
0.45 0.55 0.45 0.55 0.45 0.55 0.45 0.55 0.45 0.55 tCK
—
Clock low level width tCL
0.45 0.55 0.45 0.55 0.45 0.55 0.45 0.55 0.45 0.55 tCK
—
—
Minimum clock half tHP
tCH,
—
tCH,
—
tCH,
—
tCH,
—
tCH,
—
tCK
period
tCL
tCL
tCL
tCL
tCL
Command and Address Setup and Hold Times
Address and
Command input
setup time
tIS
0.65 —
0.65 —
0.75 —
0.75 —
1.0
1.0
—
—
1.0
1.0
—
—
ns
ns
—
—
Address and
Commandinputhold
time
tIH
0.65 —
0.65 —
Common Parameters
Row Cycle Time
tRC
39
45
—
—
42.9 —
49.5 —
46.8 —
54
63
—
—
60
70
—
—
ns
ns
—
—
Row Cycle Time in tRFC
54
—
Auto Refresh
Row Active Time
tRAS
tRAP
27
15.7k 29.7 15.7k 32.4 15.7k 36
15.7k 40
15.7k ns
ns
—
—
ACTIVE to READ
with Auto precharge
command
tRAS (min.)- (burst length * tCK /2)
Row Precharge
Time
tRP
12
—
—
13.2 —
14.4 —
18
—
—
20
—
—
ns
ns
—
—
Activate(a) to
Activate(b)
tRRD
9.0
9.0
—
9.0
—
9.0
9.0
Command period
CAS(a) to CAS(b)
Command period
tCCD
1
6
—
—
1
6
—
—
1
6
—
—
1
6
—
—
1
6
—
—
tCK
tCK
—
—
Last data in to Active tDAL
(tWR + tRP)
Data Sheet
44
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Electrical Characteristics
Table 17
Timing Parameters for speed sorts –3, –3.3, –3.6, –4.5, and –5 (cont’d)
Part Number Extension
Interface
–3
–3.3
MIM
–3.6
MIM
–4.5
–5
Unit Note1)
2)
MIM
WM/MIM
WM/MIM
—
Parameter
Symbol min. max. min. max. min. max. min. max. min. max. —
—
Read Cycle Timing Parameters for Data and Data Strobe
Data Access Time
from Clock
tAC
-0.5 +0.5 -0.5 +0.5 -0.55 +0.55 -0.7 +0.7 -0.7 +0.7 ns
-0.5 +0.5 -0.5 +0.5 -0.55 +0.55 -0.7 +0.7 -0.7 +0.7 ns
—
—
—
—
—
DQS edge to Clock tDQSCK
edge skew
DQS Read
Preamble
tRPRE
tRPST
0.7 0.9
0.8 1.1
0.7 0.9
0.8 1.1
0.7
0.8
4
0.9
1.1
—
0.7 0.9
0.8 1.1
0.7 0.9
0.8 1.1
tCK
tCK
tCK
DQS Read
Postamble
Row to Column
Delay Time for
Reads
tRCDDC
4
—
4
—
4
—
4
—
DQS edge to output tDQSQ
data edge skew
—
—
+0.3
0.33
—
—
+0.3
0.33
—
—
+0.33 —
+0.45 —
0.45
tHP-tQHS
+0.5 ns
—
—
—
Data hold skew
factor
tQHS
tQH
0.36
—
—
0.5
ns
ns
Data Output Hold
time from DQS
tHP-tQHS
tHP-tQHS
tHP-tQHS
tHP-tQHS
Write Cycle Timing Parameters for Data and Data Strobe
Row to Column
Delay Time for
Writes
tRCDWR
2
—
2
—
2
—
2
—
2
—
tCK
—
Clock to rising Edge tDQSS
DQS (Write Latency)
0.75 1.1
0.75 1.1
0.40 —
0.40 —
0.40 —
0.40 —
0.75 1.1
0.40 —
0.40 —
0.40 —
0.40 —
0.75 1.25 0.75 1.25 tCK
—
—
—
—
—
—
—
—
Data-in to DQS
Setup Time
tQDQSS 0.40 —
0.6
0.6
0.6
0.6
0
—
—
—
—
—
0.6
0.6
0.6
0.6
0
—
—
—
—
—
ns
ns
ns
ns
tCK
tCK
tCK
Data-in to DQS Hold tQDQSH
Time
0.40 —
Data Mask to DQS tDMDQSS 0.40 —
Setup Time
Data Mask to DQS tDMDQSH 0.40 —
Hold Time
Clock to DQS Write tWPRES
Preamb. Setup Time
0
—
0
—
0
—
Clock to DQS Write tWPREH 0.25 —
Preamble Hold Time
0.25 —
0.25 —
0.25 —
0.25 —
DQS Write
Postamble Hold
Time
tWPST
0.4 0.6
0.4 0.6
0.4
2
0.6
0.4 0.6
0.4 0.6
3)
Write Recovery
Time
tWR
2
—
2
—
—
2
—
2
—
tCK
Data Sheet
45
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Electrical Characteristics
Table 17
Timing Parameters for speed sorts –3, –3.3, –3.6, –4.5, and –5 (cont’d)
Part Number Extension
Interface
–3
–3.3
MIM
–3.6
MIM
–4.5
–5
Unit Note1)
2)
MIM
WM/MIM
WM/MIM
—
Parameter
Symbol min. max. min. max. min. max. min. max. min. max. —
—
Internal WRITE to
READ command
delay
tWTR
1
—
1
—
1
—
1
—
1
—
tCK
—
Write DQS High
level Width
tDQSH
0.35 0.65 0.35 0.65 0.35 0.65 0.35 0.65 0.35 0.65 tCK
0.35 0.65 0.35 0.65 0.35 0.65 0.35 0.65 0.35 0.65 tCK
—
—
Write DQS Low level tDQSL
Width
Refresh Cycle
Refresh Period
(4096 cycles)
tREF
—
—
—
32
—
—
—
32
—
—
—
32
—
—
—
32
—
—
—
32
ms
us
—
—
—
Average periodic
refresh interval
tREFC
7.8
15.7
7.8
15.7
7.8
15.7
7.8
15.7
7.8
Refresh to Refresh tREFC
15.7 µs
command interval
Mode Setup, Power Down & Self Refresh
Mode Register Set tMRD
cycle time
2
—
—
—
2
—
—
—
2
—
—
—
2
—
—
—
2
—
—
—
tCK
tCK
ns
—
—
—
Self Refresh Exit
time
tSREX
tPDEX
200
200
200
200
200
Power Down Exit
time
2*tCK
+ tIS
2*tCK
+ tIS
2*tCK
+ tIS
1*tCK
+ tIS
1*tCK
+ tIS
1) All parameters only valid for: TA = 0 to 70 °C; VSS = 0 V; 2.5 V < VDD < 2.9 V for –3 and –3.3; 2.375 V < VDD < 2.9 V for
–3.6; VDD = 2.5 V ±0.125 V for –4.5 and –5; VDDQ = 2.5 V ±0.125 V
2) Maximum clock rate is only guaranteed with the specified interface. The SSTL2-Weak Mode interface is limited to a
maximum speed of 250MHz.
3) The Write Recovery Time starts at the first rising edge of clock after the last valid (falling) DQS edge of the slowest DQS
signal.
Table 18
Timing Parameters for speed sorts L3.6 and L4.5
Part Number Extension
Interface
L3.6
MIM
L4.5
Unit Note 1)
2)
WM/MIM
—
Parameter
Symbol min.
max. min.
max.
—
—
Clock and Clock Enable
Clock Cycle Time
3.6
6.0
10
4.5
6.0
10
ns
ns
CL = 4
CL = 3
tCK
fCK
fCK
tCH
4.2
4.5
166
100
System frequency
166
100
0.45
278
238
222
222
MHz CL = 4
MHz CL = 3
Clock high level width
0.55 0.45
0.55 tCK
—
Data Sheet
46
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Electrical Characteristics
Table 18
Timing Parameters for speed sorts L3.6 and L4.5 (cont’d)
Part Number Extension
Interface
L3.6
MIM
L4.5
Unit Note 1)
2)
WM/MIM
—
Parameter
Symbol min.
max. min.
max.
—
—
Clock low level width
tCL
tHP
0.45
0.55 0.45
0.55 tCK
—
—
Minimum clock half period
tCH, tCL
—
tCH, tCL
—
tCK
Command and Address Setup and Hold Times
Address and Command input setup time
Address and Command input hold time
tIS
tIH
0.75
0.75
—
—
1.0
1.0
—
—
ns
ns
—
—
Common Parameters
Row Cycle Time
tRC
46.8
54
—
—
54
63
—
—
ns
ns
—
—
—
—
—
—
—
—
Row Cycle Time in Auto Refresh
Row Active Time
tRFC
tRAS
32.4
15.7k 36
15.7k ns
ACTIVE to READ with Auto precharge command tRAP
tRAS (min.)- (burst length * tCK /2) ns
Row Precharge Time
tRP
14.4
9.0
1
—
—
—
—
18
9.0
1
—
—
—
—
ns
ns
tCK
tCK
Activate(a) to Activate(b) Command period
CAS(a) to CAS(b) Command period
Last data in to Active (tWR + tRP)
tRRD
tCCD
tDAL
6
6
Read Cycle Timing Parameters for Data and Data Strobe
Data Access Time from Clock
DQS edge to Clock edge skew
DQS Read Preamble
tAC
-0.55
-0.55
0.7
0.8
4
+0.55 -0.7
+0.55 -0.7
+0.7 ns
+0.7 ns
—
—
—
—
—
—
—
—
tDQSCK
tRPRE
tRPST
tRCDDC
tDQSQ
tQHS
0.9
1.1
—
0.7
0.8
4
0.9
1.1
—
tCK
tCK
tCK
DQS Read Postamble
Row to Column Delay Time for Reads
DQS edge to output data edge skew
Data hold skew factor
—
+0.33 —
+0.45 ns
0.45 ns
HP – tQHS ns
—
0.36
—
Data Output Hold time from DQS
tQH
t
HP – tQHS
t
Write Cycle Timing Parameters for Data and Data Strobe
Row to Column Delay Time for Writes
Clock to rising Edge DQS (Write Latency)
Data-in to DQS Setup Time
tRCDWR
tDQSS
tQDQSS
tQDQSH
2
—
1.1
—
—
—
—
—
—
0.6
—
2
—
tCK
—
—
—
—
—
—
—
—
0.75
0.40
0.40
0.75
0.6
0.6
0.6
0.6
0
1.25 tCK
—
—
—
—
—
—
0.6
—
ns
ns
ns
ns
tCK
tCK
tCK
tCK
Data-in to DQS Hold Time
Data Mask to DQS Setup Time
Data Mask to DQS Hold Time
tDMDQSS 0.40
tDMDQSH 0.40
Clock to DQS Write Preamb. Setup Time
Clock to DQS Write Preamble Hold Time
DQS Write Postamble Hold Time
Write Recovery Time
tWPRES
tWPREH
tWPST
tWR
0
0.25
0.4
2
0.25
0.4
2
—
3)
Data Sheet
47
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Electrical Characteristics
Table 18
Timing Parameters for speed sorts L3.6 and L4.5 (cont’d)
Part Number Extension
Interface
L3.6
MIM
L4.5
Unit Note 1)
2)
WM/MIM
—
Parameter
Symbol min.
max. min.
max.
—
—
Internal WRITE to READ command delay
Write DQS High level Width
Write DQS Low level Width
tWTR
1
—
1
—
tCK
—
—
—
tDQSH
tDQSL
0.35
0.35
0.65 0.35
0.65 0.35
0.65 tCK
0.65 tCK
Refresh Cycle
Refresh Period (4096 cycles)
tREF
—
—
—
32
—
—
—
32
ms
us
—
—
—
Average periodic refresh interval
Refresh to Refresh command interval
tREFC
tREFC
7.8
15.7
7.8
15.7 us
Mode Setup, Power Down & Self Refresh
Mode Register Set cycle time
Self Refresh Exit time
tMRD
2
—
—
—
2
—
—
—
tCK
tCK
ns
—
—
—
tSREX
tPDEX
200
200
Power Down Exit time
2*tCK+tIS
1*tCK+tIS
1) All parameters only valid for: TA = 0 to 70 °C; VSS = 0 V; 2.375 V < VDD < 2.9 V for L3.6; VDD = 2.5 V ± 0.125 V for L4.5;
DDQ = 2.5 V ±0.125 V
V
2) Maximum clock rate is only guaranteed with the specified interface. The SSTL2-Weak Mode interface is limited to a
maximum speed of 250MHz.
3) The Write Recovery Time starts at the first rising edge of clock after the last valid (falling) DQS edge of the slowest DQS
signal.
Table 19
HYB25D128323C–3
Frequency / tCK
CAS latency
tRC tRFC tRAS tRP tWR tRRD tDAL tRCDRD tRCDWR
Units
333 MHz / 3.0 ns
4
13 15
13 15
13 15
12 14
10 12
9
9
9
8
7
6
4
4
4
4
3
3
2
2
2
2
2
2
3
3
3
3
2
2
6
6
6
6
5
5
4
4
4
3
3
3
2
2
2
2
2
2
tCK
300 MHz / 3.3 ns
278 MHz / 3.6 ns
250 MHz / 4.0 ns
222 MHz / 4.5 ns
200 MHz / 5.0 ns
4
4
3
3
3
tCK
tCK
tCK
tCK
tCK
9
11
Data Sheet
48
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Electrical Characteristics
Table 20
HYB25D128323C–3.3
Frequency / tCK
CAS latency
tRC tRFC tRAS tRP tWR tRRD tDAL tRCDRD tRCDWR
Units
300 MHz / 3.3 ns
4
13 15
13 15
12 14
10 12
9
9
8
7
6
4
4
4
3
3
2
2
2
2
2
3
3
3
2
2
6
6
6
5
5
4
4
3
3
3
2
2
2
2
2
tCK
278 MHz / 3.6 ns
250 MHz / 4.0 ns
222 MHz / 4.5 ns
200 MHz / 5.0 ns
4
3
3
3
tCK
tCK
tCK
tCK
9
11
Table 21
HYB25D128323C–3.6
Frequency / tCK
CAS latency
tRC tRFC tRAS tRP tWR tRRD tDAL tRCDRD tRCDWR Units
278 MHz / 3.6 ns
4
13 15
13 15
12 14
10 12
9
9
8
7
4
4
4
3
2
2
2
2
3
3
2
2
6
6
6
5
4
4
4
3
2
2
2
2
tCK
tCK
tCK
tCK
250 MHz / 4.0 ns
222 MHz / 4.5 ns
200 MHz / 5.0 ns
4
3
3
Table 22
HYB25D128323C–4.5
Frequency / tCK
CAS latency
tRC tRFC tRAS tRP tWR tRRD tDAL tRCDRD tRCDWR Units
222 MHz / 4.5 ns
3
12 14
12 14
12 14
8
8
8
4
4
4
2
2
2
2
2
2
6
6
6
4
4
4
2
2
2
tCK
tCK
tCK
200 MHz / 5.0 ns
183 MHz / 5.5 ns
3
3
Table 23
HYB25D128323C–5
Frequency / tCK
CAS latency
tRC tRFC tRAS tRP tWR tRRD tDAL tRCDRD tRCDWR Units
200 MHz / 5.0 ns
3
12 14
8
4
2
2
6
4
2
tCK
183 MHz / 5.5 ns
3
12 14
8
4
2
2
6
4
2
tCK
Data Sheet
49
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Electrical Characteristics
Table 24
HYB25D128323CL3.6
Frequency / tCK
CAS latency
tRC tRFC tRAS tRP tWR tRRD tDAL tRCDRD tRCDWR Units
278 MHz / 3.6 ns
4
13 15
13 15
12 14
10 12
9
9
8
7
6
4
4
4
3
3
2
2
2
2
2
3
3
2
2
2
6
6
6
5
5
4
4
4
3
3
2
2
2
2
2
tCK
tCK
tCK
tCK
tCK
250 MHz / 4.0 ns
222 MHz / 4.5 ns
200 MHz / 5.0 ns
166 MHz / 6.0 ns
4
3
3
3
9
11
Table 25
HYB25D128323CL4.5
Frequency / tCK
CAS latency
tRC tRFC tRAS tRP tWR tRRD tDAL tRCDRD tRCDWR Units
222 MHz / 4.5 ns
3
12 14
12 14
12 14
10 12
8
8
8
7
6
4
4
4
3
3
2
2
2
2
2
2
2
2
2
2
6
6
6
5
5
4
4
4
3
3
2
2
2
2
2
tCK
tCK
tCK
tCK
tCK
200 MHz / 5.0 ns
183 MHz / 5.5 ns
166 MHz / 6.0 ns
143 MHz / 7.0 ns
3
3
3
3
9
11
Table 26
Operating Currents
Parameter & Test Condition
Symbol –3
max.
200 190 180 160 150
–3.3 –3.6 –4.5 –5.0 L3.6 L4.5 Unit Notes
typ. typ.
1)
OPERATING CURRENT: One bank; IDD0
mA
mA
mA
Active-Precharge; tRC = tRC(min.)
CK = tCK(min.); DQ, DM and DQS inputs
changing once per clock cycle;
;
t
Address and control inputs changing
once every two clock cycles
OPERATING CURRENT: One bank; IDD1
Active-Read-Precharge; BL=4; CL=4;
230 220 110 190 180
t
t
RCDDC = 4*tCK; tRC = tRC(min.)
CK = tCK(min.); IOUT = 0mA; Address and
;
control inputs changing once per clock
cycle
PRECHARGE POWER-DOWN
IDD2P
26
22
22
14
14
10
7
STANDBY CURRENT: All banks idle;
power-down mode; tCK = tCK(min.)
;
CKE=LOW
Data Sheet
50
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Electrical Characteristics
Table 26
Operating Currents (cont’d)
Parameter & Test Condition
Symbol –3
max.
–3.3 –3.6 –4.5 –5.0 L3.6 L4.5 Unit Notes
typ. typ.
IDLE STANDBY CURRENT:
CKE=HIGH; CS#=HIGH
IDD2F
130 120 110 100 100
mA
(DESELECT); All banks idle;
t
CK = tCK(min.); Address and control
inputs changing once per clock cycle;
VIN = VREF for DQ, DQS and DM
ACTIVE POWER-DOWN STANDBY IDD3P
CURRENT: one bank active; power-
65
60
55
50
50
mA
mA
down mode; CKE=LOW; tCK = tCK(min.)
;
ACTIVE STANDBY CURRENT:
CS#=HIGH; CKE=HIGH; one bank
IDD3N
130 120 110 100 100
active; tRC = tRC(max.); tCK = tCK(min.)
;
Address and control inputs changing
once per clock cycle; DQ, DQS, and
DM inputs changing twice per clock
cycle
OPERATING CURRENT BURST
READ: BL=2; READS; Continuous
burst; one bank active; Address and
IDD4R
370 350 330 290 280 190 160 mA
control inputs changing once per clock
cycle; tCK = tCK(min.); Iout=0mA; 50% of
data changing on every transfer
OPERATING CURRENT BURST
WRITE: BL=2; WRITES; Continuous
burst; one bank active; Address and
control inputs changing once per clock
cycle; tCK = tCK(min.); DQ, DQS, and DM
changing twice per clock cycle; 50% of
data changing on every transfer
IDD4W
370 350 330 290 280 200 175 mA
AUTO REFRESH CURRENT:
IDD5
IDD6
320 300 280 240 230
20 16 16 10 10
mA
mA
t
RC = tRFC(min.); tCK = tCK(min.)
SELF REFRESH CURRENT: Self
Refresh Mode; CKE<=0.2V;
4
3
t
CK = tCK(min.)
1)
BURST OPERATING CURRENT 4
bank operation:
IDD7
430 400 370 320 300
mA
Four bank interleaving READs; BL=4;
with Auto Precharge; tRC = tRC(min.)
;
t
CK = tCK(min.); Address and control
inputs change only during Active,
READ, or WRITE commands
1) Measured with output open.
Data Sheet
51
V1.7, 2003-07
HYB25D128323C[-3/-3.3/-3.6/-4.5/-5.0/L3.6/L4.5]
128 Mbit DDR SGRAM [4M x 32]
Package Outlines
5
Package Outlines
Module Package
The package is conforming with JEDEC MO-205 Variation BD
General Tolerances according to ISO 8015
The inner matrix of 4 × 4 balls is reserved for thermal contacts
11.1
10.9
0.10
11.1
10.9
1.50
1.44
1.36
8.8
8.8
0.8
--
0.8
--
- -
0.85
8.8
8.8
MAX
MAX
MIN
All dimensions in mm. Notation is TYP or
MIN
or TYP
Figure 32 Package Outlines
Data Sheet
52
V1.7, 2003-07
w w w . i n f i n e o n . c o m
Published by Infineon Technologies AG
相关型号:
©2020 ICPDF网 联系我们和版权申明