AUIPS6031STRL [INFINEON]
Buffer/Inverter Based Peripheral Driver, 1 Driver, 16A, PSSO4, ROHS COMPLIANT, TO-263BA, DDPAK-5/4;型号: | AUIPS6031STRL |
厂家: | Infineon |
描述: | Buffer/Inverter Based Peripheral Driver, 1 Driver, 16A, PSSO4, ROHS COMPLIANT, TO-263BA, DDPAK-5/4 驱动 接口集成电路 驱动器 |
文件: | 总17页 (文件大小:1115K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
September, 12th 2011
Automotive grade
AUIPS6031(S)(R)
Done please find
INTELLIGENT POWER HIGH SIDE SWITCH
Features
Product Summary
Over temperature shutdown (with auto-restart)
Short circuit protection (current limit)
Reverse battery protection (turns On the MOSFET)
Full diagnostic capability (short circuit to battery)
Active clamp
Open load detection in On and Off state
Ground loss protection
Logic ground isolated from power ground
ESD protection
Lead Free and RoHS compliant
Rds(on)
Vclamp
I Limit
60m max.
39V
16A
Open load 3V / 0.55A
Packages
Description
The AUIPS6031(S)(R) is a five terminal Intelligent Power
Switch (IPS) for use in a high side configuration. It features
short circuit, over-temperature, ESD protection, inductive load
capability and diagnostic feedback. The output current is
limited to the Ilim value. The current limitation is activated until
the thermal protection acts. The over-temperature protection
turns off the device if the junction temperature exceeds the
Tshutdown value. It will automatically restart after the junction
has cooled 7°C below the Tshutdown value. The reverse
battery protection turns On the MOSFET. A diagnostic pin
provides different voltage levels for each fault condition. The
double level shifter circuitry will allow large offsets between
the logic and load ground.
TO-220
AUIPS6031
D²Pak
AUIPS6031S
D-Pak
AUIPS6031R
Typical Connection
+5V
+Bat
Vcc(3)
Rdgp
Dg(4)
Pull-up resistors required for
open load off and short
circuit to Vbat detection
Control
Rdgs
In(2) Gnd(1)
Out(5)
Load
V Diag
Rin
Input Signal
1
www.irf.com
AUIPS6031(S)(R)
†
Qualification Information
Automotive
(per AEC-Q100††)
Qualification Level
Comments: This family of ICs has passed an Automotive qualification. IR’s
Industrial and Consumer qualification level is granted by extension of the higher
Automotive level.
MSL1, 260°C
D2PAK-5L
(per IPC/JEDEC J-STD-020)
Not applicable
TO-220
Moisture Sensitivity Level
(non-surface mount package style)
MSL1, 260°C
DPAK-5L
(per IPC/JEDEC J-STD-020)
Class M2 (+/-150V) †††
(per AEC-Q100-003)
Machine Model
Class H1C (+/-1500V) †††
Human Body Model
(
)
per AEC-Q100-002
ESD
Charged Device Model
Class C4 (+/-900V)†††
(per AEC-Q100-011)
Class C3B (+/-750V) †††
(per AEC-Q100-011)
Class II, Level A
(DPAK,D2PAK)
Charged Device Model
(TO220)
IC Latch-Up Test
RoHS Compliant
(per AEC-Q100-004)
Yes
†
Qualification standards can be found at International Rectifier’s web site http://www.irf.com/
††
Exceptions to AEC-Q100 requirements are noted in the qualification report.
††† Passing voltage level
2
www.irf.com
AUIPS6031(S)(R)
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters
are referenced to Ground lead. Tj= -40°C..150°C, Vcc=6..35V (unless otherwise specified).
Symbol
Vout
Parameter
Maximum output voltage
Min. Max. Units
Vcc-35 Vcc+0.3
Voffset
Vin
Maximum logic ground to load ground offset
Maximum input voltage
Maximum Vcc voltage
Maximum continuous Vcc voltage
Maximum Vcc voltage with short circuit protection
Maximum IN current
Maximum diagnostic output current
Maximum diagnostic output voltage
Maximum power dissipation (internally limited by thermal protection)
Rth=5°C/W AUIPS6031
Vcc-35 Vcc+0.3
-0.3
-3
5.5
36
28
30
10
10
5.5
V
Vcc max.
Vcc cont.
Vcc sc.
Iin max.
Idg max.
Vdg
mA
V
-3
-0.3
25
3.1
2.5
150
Pd
W
Rth=40°C/W AUIPS6031S 1”sqrt. footprint
Rth=50°C/W AUIPS6031R 1”sqrt. footprint
Max. storage & operating temperature junction temperature
Tj max.
-40
°C
Thermal Characteristics
Symbol
Rth1
Parameter
Typ. Max. Units
Thermal resistance junction to ambient AUIPS6031 TO220 free air
Thermal resistance junction to case AUIPS6031 TO220
Thermal resistance junction to ambient AUIPS6031S D²Pak std. footprint
Thermal resistance junction to ambient AUIPS6031S D²Pak 1” sqrt.
footprint
50
3.8
60
Rth2
Rth1
Rth2
40
°C/W
Rth3
Rth1
Thermal resistance junction to case AUIPS6031S D²Pak
Thermal resistance junction to ambient AUIPS6031R D-Pak std. footprint
Thermal resistance junction to ambient AUIPS6031R D-Pak 1” sqrt.
footprint
3.8
70
Rth2
Rth3
50
Thermal resistance junction to case AUIPS6031R D-Pak
3.8
Recommended Operating Conditions
These values are given for a quick design. For operation outside these conditions, please consult the application notes.
Symbol
VIH
Parameter
High level input voltage
Min. Max. Units
4
5.5
VIL
Low level input voltage
0
0.9
Iout
Continuous drain current, Tambient=85°C, Tj=125°C, Vin=5V
Rth=5°C/W AUIPS6031
4
A
8.9
3.1
2.8
10
Rth=40°C/W AUIPS6031S 1” sqrt. footprint
Rth=50°C/W AUIPS6031R 1” sqrt. footprint
Recommended resistor in series with IN pin
Recommended resistor in series with DG pin for reverse battery protection
Recommended pull-up resistor for DG
Recommended pull-up resistor for open load detection
Max. switching frequency
Rin
Rdgs
Rdgp
Rol
4
4
5
20
20
100
2.5
k
F max.
kHz
3
www.irf.com
AUIPS6031(S)(R)
Static Electrical Characteristics
Tj=-40°C..150°C, Vcc=6..28V (unless otherwise specified), typical values are given for Vcc=14V and Tj=25°C
Symbol
Rds(on)
Parameter
Min. Typ. Max. Units Test Conditions
ON state resistance Tj=25°C
ON state resistance Tj=150°C
ON state resistance Tj=25°C, Vcc=6V
ON state resistance during reverse battery
Tj=25°C
46
83
55
60
60
100
70
Vin=5V, Iout=5A
Vin=5V, Iout=5A
Vin=5V, Iout=2.5A
Vcc-Gnd=-14V
m
80
39
40
4
Vcc op.
Operating voltage range
Vcc to Out clamp voltage 1
Vcc to Out clamp voltage 2
Supply current when Off and Vout
connected to ground with R<4Ω
Supply current when On
Input high threshold voltage
Input low threshold voltage
Input hysteresis
6
28
43
9
V clamp 1
V clamp 2
Icc Off
37
V
Iout=30mA
Iout=4A (see Fig. 1)
Vin=0V, Vout=0V,
Tj=25°C, Vcc=14V
Vin=5V, Vcc=14V
µA
1.5
0.2
Icc On
Vih
Vil
In hyst.
Iin On
Idg
2.2
2.5
2
0.5
40
5
3
mA
V
1
Input current when device is On
Dg leakage current
Low level DG voltage
100
10
0.4
Vin=5V
Vdg=5V
Idg=1.6mA
µA
V
0.1
0.25
Vdg
Switching Electrical Characteristics
Vcc=14V, Resistive load=6, Vin=5V, Tj=-40°C..150°C, typical values are given for Tj=25°C
Symbol
Tdon
Tr1
Tr2
dV/dt (On)
EOn
Tdoff
Tf
dV/dt (Off)
EOff
Parameter
Min. Typ. Max. Units Test Conditions
Turn-on delay time
Rise time to Vout=Vcc-5V
Rise time to Vout=0.9 x Vcc
Turn On dV/dt
8
5
8
1.5
150
20
9
3
65
25
20
35
µs
V/µs
µJ
Turn On energy
see Fig. 3
Turn-off delay time
Fall time to Vout=0.1 x Vcc
Turn Off dV/dt
45
30
µs
V/µs
µJ
Turn Off energy
4
www.irf.com
AUIPS6031(S)(R)
Protection Characteristics
Tj=-40°C..150°C, Vcc=6..28V (unless otherwise specified), typical values are given for Vcc=14V and Tj=25°C
Symbol
Ilim
Parameter
Internal current limit
Min. Typ. Max. Units
Test Conditions
Vout=0V, Tj=25°C
10
16
23
A
4
6.2
5.8
4
Tsd+
Tsd-
Vsc
UV+
UV-
Over temperature high threshold
Over temperature low threshold
Short-circuit detection voltage(2)
Under voltage protection Vcc going up
Under voltage protection Vcc going down
Open load detection threshold
150(1) 165
°C
See fig. 2
2
158
3
2
5
4.5
3
V
A
VOL Off
Open load detection threshold
0.15
0.15
0.4
0.4
0.65
0.55
Tj=-40..25°C
Tj=25..150°C
I OL On
(1) Guaranteed by design
(2) Reference to Vcc
True Table
Operating Conditions
Normal
IN
H
L
OUT
H
L
DG
H
H
Normal
Open Load
Open Load (3)
H
L
H
H
L
L
Short circuit to Gnd
Short circuit to Gnd
Short circuit to Vcc
Short circuit to Vcc (5)
Over-temperature
Over-temperature
H
L
H
L
H
L
L
L
H
H
L
L
L
H
L (4)
L
L
H
(3) With a pull-up resistor connected between the output and Vcc.
(4) Vds lower than 10mV.
(5) Without a pull-up resistor connected between the output and Vcc.
Lead Assignments
5
www.irf.com
AUIPS6031(S)(R)
Functional Block Diagram
All values are typical
VCC
165°C
158°C
Tj
37V
Charge
Pump
43V
Vcc-gnd >UV
Level
Shifter
43V
2.5V
2.0V
Driver
IN
6V
-
Over-temp
+
I sense
I Limit
Open load off
+
-
DG
6V
-
Short circuit
3V
+
3V
Open load on
-
Ground
Disconnect
+
20mV
GND
OUT
6
www.irf.com
AUIPS6031(S)(R)
T clamp
Vin
Vin
Ids
Iout
limiting
Thermal cycling
Ilim
Vcc
Tj
Tsd+
Tsd-
Vds
Vds clamp
DG
See Application Notes to evaluate power dissipation
Figure 1 – Active clamp waveforms
Figure 2 – Protection timing diagram
90%
10%
Vin
Dg
In
Vcc
Out
Vclamp
L
Tr-in
Gnd
+
14V
Vcc
-
90%
Vcc-5V
5V
0V
Vout
Rem :
During active
clamp, Vload
is negative
Vout
Vin
R
10%
Td on
Td off
Iout
Tr1
Tf
Tr2
Figure 3 – Switching times definitions
Figure 4 – Active clamp test circuit
7
www.irf.com
AUIPS6031(S)(R)
200%
150%
100%
50%
800
600
400
200
0
Eon
Eoff
0
2
4
6
8
10
-50
0
50
100
150
Iout, Output current (A)
Tj, junction temperature (°C)
Figure 5 – Switching energy (µJ) Vs Output
Figure 6 - Normalized Rds(on) (%) Vs Tj (°C)
current (A)
100
10
1
20
TO 220 5°C/W
D2Pak 40°C/W
DPak 50°C/W
15
10
5
0
-50
0
50
100
150
0.001
0.01
0.1
1
10
Load inductance (mH)
Tamb, Ambient temperature (°C)
Figure 7 – Max. Output current (A) Vs Load
Figure 8 – Max. ouput current (A)
Vs Ambient temperature (°C)
inductance (mH)
8
www.irf.com
AUIPS6031(S)(R)
100
10
20
10
0
1
0.1
0.01
1e-5 1e-4 1e-3 1e-2 1e-1 1e+0 1e+1 1e+2 1e+3
-50
0
50
100
Time (s)
Tj, junction temperature (°C)
Figure 9 – Transient thermal impedance (°C/W)
Figure 10 –I limit (A)
Vs time (s)
Vs junction temperature (°C)
1.E+4
1.E+4
1.E+3
1.E+2
1.E+1
1.E+0
1.E+3
Icc on
Icc off
Icc on
Icc off
1.E+2
1.E+1
1.E+0
0
5
10
15
20
25
30
-50
0
50
100
150
Vcc, power supply voltage (V)
Tj, junction temperature (°C)
Figure 11 – Icc on/ Icc off (µA) Vs Vcc (V)*
*Vout connected to ground with R<4Ω
Figure 12 – Icc on/ Icc off (µA) Vs Tj (°C)*
9
www.irf.com
AUIPS6031(S)(R)
Case Outline - TO220 (5 leads)
10
www.irf.com
AUIPS6031(S)(R)
Case Outline D2PAK - 5 Leads
11
www.irf.com
AUIPS6031(S)(R)
Tape & Reel D2PAK - 5 Leads
12
www.irf.com
AUIPS6031(S)(R)
Case Outline DPAK - 5 Leads
13
www.irf.com
AUIPS6031(S)(R)
Tape & Reel DPAK - 5 Leads
14
www.irf.com
AUIPS6031(S)(R)
Part Marking Information
Ordering Information
Standard Pack
Form
Base Part Number
Package Type
Complete Part Number
Quantity
50
AUIPS6031
TO220-5-Leads
Tube
Tube
AUIPS6031
AUIPS6031S
50
AUIPS6031S
D2-Pak-5-Leads
Tape and reel left
Tape and reel right
Tube
800
AUIPS6031STRL
AUIPS6031STRR
AUIPS6031R
800
75
Tape and reel
2000
3000
3000
AUIPS6031RTR
AUIPS6031RTRL
AUIPS6031RTRR
AUIPS6031R
D-Pak-5-Leads
Tape and reel left
Tape and reel right
15
www.irf.com
AUIPS6031(S)(R)
IMPORTANT NOTICE
Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR)
reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and
services at any time and to discontinue any product or services without notice. Part numbers designated with the “AU”
prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and
process change notification. All products are sold subject to IR’s terms and conditions of sale supplied at the time of order
acknowledgment.
IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with
IR’s standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary to
support this warranty. Except where mandated by government requirements, testing of all parameters of each product is
not necessarily performed.
IR assumes no liability for applications assistance or customer product design. Customers are responsible for their
products and applications using IR components. To minimize the risks with customer products and applications,
customers should provide adequate design and operating safeguards.
Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and
is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with
alterations is an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation.
Information of third parties may be subject to additional restrictions.
Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or
service voids all express and any implied warranties for the associated IR product or service and is an unfair and
deceptive business practice. IR is not responsible or liable for any such statements.
IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into
the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the
IR product could create a situation where personal injury or death may occur. Should Buyer purchase or use IR products
for any such unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the design or manufacture of
the product.
IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR
products are specifically designated by IR as military-grade or “enhanced plastic.” Only products designated by IR as
military-grade meet military specifications. Buyers acknowledge and agree that any such use of IR products which IR has
not designated as military-grade is solely at the Buyer’s risk, and that they are solely responsible for compliance with all
legal and regulatory requirements in connection with such use.
IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR
products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the
designation “AU”. Buyers acknowledge and agree that, if they use any non-designated products in automotive
applications, IR will not be responsible for any failure to meet such requirements.
For technical support, please contact IR’s Technical Assistance Center
http://www.irf.com/technical-info/
WORLD HEADQUARTERS:
101 N Sepulbeda Blvd., El Segundo, California 90245
Tel: (310) 252-7105
16
www.irf.com
AUIPS6031(S)(R)
Revision History
Revision
B
C
Date
September, 12th 2011
May 15, 2012
Notes/Changes
AU release
Add the test condition for the ICC (off)
parameters
17
www.irf.com
相关型号:
AUIPS6031STRR
Buffer/Inverter Based Peripheral Driver, 16A, PSSO4, ROHS COMPLIANT, TO-263BA, DDPAK-5/4
INFINEON
AUIPS6041
Buffer/Inverter Based Peripheral Driver, 1 Driver, 7A, ROHS COMPLIANT, TO-220, 5 PIN
INFINEON
AUIPS6041GTR
Buffer/Inverter Based Peripheral Driver, 1 Driver, 7A, PDSO8, ROHS COMPLIANT, MS-012AA, SOIC-8
INFINEON
AUIPS6041RTRL
Buffer/Inverter Based Peripheral Driver, 1 Driver, 7A, PSSO4, ROHS COMPLIANT, DPAK, TO-252, 5 PIN
INFINEON
AUIPS6041S
Buffer/Inverter Based Peripheral Driver, 1 Driver, 7A, PSSO5, ROHS COMPLIANT, TO-263BA, D2PAK-5
INFINEON
AUIPS6041STRL
Buffer/Inverter Based Peripheral Driver, 1 Driver, 7A, PSSO5, ROHS COMPLIANT, TO-263BA, D2PAK-5
INFINEON
©2020 ICPDF网 联系我们和版权申明