X24645IG [ICMIC]
Advanced 2-Wire Serial E2PROM with Block LockTM Protection; 先进的2线串行E2PROM带座LockTM保护型号: | X24645IG |
厂家: | IC MICROSYSTEMS |
描述: | Advanced 2-Wire Serial E2PROM with Block LockTM Protection |
文件: | 总18页 (文件大小:317K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TM
This X24645 device has been acquired by
IC MICROSYSTEMS from Xicor, Inc.
ICmic
8192 x 8 Bit
IC MICROSYSTEMS
64K
X24645
2
Advanced 2-Wire Serial E PROM with Block LockTM Protection
FEATURES
DESCRIPTION
The X24645 is a CMOS 65,536-bit serial E2PROM,
internally organized 8192 x 8. The X24645 features a
•2.7V to 5.5V Power Supply
•Low Power CMOS
—Active Read Current Less Than 1mA
—Active Write Current Less Than 3mA
serial interface and software protocol allowing operation
on a simple two wire bus.
—Standby Current Less Than 1∝A
•Internally Organized 8192 x 8
•New Programmable Block Lock Protection
—Software Write Protection
—Programmable hardware Write Protect
Two device select inputs (S1, S2) allow up to four
devices to share a common two wire bus.
A Write Protect Register at the highest address location,
1FFFh, provides three new write protection
2
•Block Lock (0, 1/4, 1/2, or all of the E PROM
array)
features: Software Write Protect, Block Write Protect, and
Hardware Write Protect. The Software Write
•2 Wire Serial Interface
Protect feature prevents any nonvolatile writes to the
X24645 until the WEL bit in the write protect register is
•Bidirectional Data Transfer Protocol
•32 Byte Page Write Mode
—Minimizes Total Write Time Per Byte
•Self Timed Write Cycle
—Typical Write Cycle Time of 5ms
•High Reliability
—Endurance: 100,000 Cycles
—Data Retention: 100 Years
•Available Packages
set. The Block Write Protection feature allows the user to
individually write protect four blocks of the array by
programming two bits in the write protect register. The
Programmable Hardware Write Protect feature allows
the user to install the X24645 with WP tied to VCC,
program the entire memory array in place, and then
enable the hardware write protection by programming a
WPEN bit in the write protect register. After this,
—8-Lead PDIP
selected blocks of the array, including the write protect
register itself, are permanently write protected, as long
as WP remains HIGH.
—8-Lead SOIC (JEDEC)
—14-Lead SOIC (JEDEC)
—20-Lead TSSOP
FUNCTIONAL DIAGRAM
WP
H.V. GENERATION
START CYCLE
TIMING &
CONTROL
V
CC
V
SS
WRITE PROTECT
REGISTER AND
SDA
START
STOP
LOGIC
LOGIC
CONTROL
LOGIC
SLAVE ADDRESS
REGISTER
2
E PROM
XDEC
256 X 256
LOAD
WORD
INC
SCL
+COMPARATOR
ADDRESS
COUNTER
S
S
2
1
R/W
YDEC
8
CK
D
OUT
PIN
DATA REGISTER
D
OUT
ACK
2783 ILL F01
Xicor, 1995, 1996 Patents Pending
Characteristics subject to change without notice
2783-3.5 5/13/96 T1/C0/D0 NS
1
X24645
ICmic E2PROMs are designed and tested for applications
requiring extended endurance. Inherent data
retention is greater than 100 years.
PIN CONFIGURATIONS
8-LEAD DIP & SOIC
V
NC
CC
1
2
8
7
PIN DESCRIPTIONS
Serial Clock (SCL)
S
1
S
2
X24645
WP
SCL
SDA
3
4
6
5
The SCL input is used to clock all data into and out of the
device.
V
SS
14-LEAD SOIC
Serial Data (SDA)
SDA is a bidirectional pin used to transfer data into and
out of the device. It is an open drain output and
NC
NC
NC
NC
1
2
14
13
may be wire-ORed with any number of open drain or
open collector outputs.
V
CC
NC
3
4
12
X24645 11
S
1
An open drain output requires the use of a pull-up
resistor. For selecting typical values, refer to the Pull-
WP
SCL
SDA
S
2
5
6
10
9
V
up resistor selection graph at the end of this data
sheet.
SS
NC
NC
7
8
Device Select (S1, S2)
20-LEAD TSSOP
The device select inputs (S1, S2) are used to set the first
and second bits of the 8-bit slave address. This
NC
NC
NC
1
2
20
19
V
CC
allows up to four X24645 devices to share a common bus.
These inputs can be static or actively driven. If
18
17
16
15
14
13
3
4
WP
NC
S
1
used statically they must be tied to V
or V
as
appropriate. If actively driven, they must be driven with
SS
CC
NC
NC
5
6
7
8
X24645
CMOS levels (driven to VCC or VSS).
NC
NC
NC
S
2
SCL
SDA
Write Protect (WP)
The write protect input controls the hardware write
protect feature. When held LOW, hardware write
V
SS
NC
NC
NC
NC
9
10
12
11
protection is disabled and the X24645 can be written
normally. When this input is held HIGH, and the WPEN
2783 ILL F02.4
bit in the write protect register is set HIGH, write
protection is enabled, and nonvolatile writes are
disabled to the selected blocks as well as the write
protect register itself.
PIN NAMES
Symbol
Description
S1, S2
Device Select Inputs
SDA
SCL
WP
Serial Data
Serial Clock
Write Protect
Ground
VSS
VCC
NC
Supply Voltage
No Connect
2783 FRM T01.1
2
X24645
DEVICE OPERATION
The X24645 supports a bidirectional bus oriented pro-
tocol. The protocol defines any device that sends data
Clock and Data Conventions
Data states on the SDA line can change only during
SCL LOW. SDA state changes during SCL HIGH are
reserved for indicating start and stop conditions. Refer to
Figures 1 and 2.
onto the bus as a transmitter, and the receiving device as
the receiver. The device controlling the transfer is a
master and the device being controlled is the slave.
The master will always initiate data transfers, and provide
Start Condition
All command are preceded by the start condition, which
is a HIGH to LOW transition of SDA when SCL is
the clock for both transmit and receive operations.
Therefore, the X24645 will be considered a slave in all
HIGH. The X24645 continuously monitors the SDA and SCL
lines for the start condition and will not respond to
any command until this condition has been met.
applications.
Figure 1. Data Validity
SCL
SDA
DATA
CHANGE
DATA STABLE
2783 ILL F04
Notes: (5) Typical values are for TA = 25°C and nominal supply voltage (5V)
(6) tWR is the minimum cycle time from the system perspective when polling techniques are not used. It is the maximum time the
device requires to perform the internal write operation.
Figure 2. Definition of Start and Stop
SCL
SDA
START BIT
STOP BIT
2783 ILL F05
3
X24645
The X24645 will respond with an acknowledge after
recognition of a start condition and its slave address. If
Stop Condition
All communications must be terminated by a stop
condition, which is a LOW to HIGH transition of SDA
both the device and a write operation have been
selected, the X24645 will respond with an acknowledge
after the receipt of each subsequent 8-bit word.
when SCL is HIGH. The stop condition is also used to
place the device into the standby power mode after a
read sequence. A stop condition can only be issued
after the transmitting device has released the bus.
In the read mode the X24645 will transmit eight bits of data,
release the SDA line and monitor the line for an
acknowledge. If an acknowledge is detected and no stop
condition is generated by the master, the X24645
Acknowledge
Acknowledge is a software convention used to indicate
successful data transfer. The transmitting device,
will continue to transmit data. If an acknowledge is not
detected, the X24645 will terminate further data trans-
either master or slave, will release the bus after trans-
mitting eight bits. During the ninth clock cycle the
missions. The master must then issue a stop condition to
return the X24645 to the standby power mode and
place the device into a known state.
receiver will pull the SDA line LOW to acknowledge
that it received the eight bits of data. Refer to Figure 3.
Figure 3. Acknowledge Response From Receiver
SCL FROM
MASTER
1
8
9
DATA OUTPUT
FROM
TRANSMITTER
DATA
OUTPUT
FROM
RECEIVER
START
ACKNOWLEDGE
2783 ILL F06
4
X24645
The last bit of the slave address defines the operation to be
performed. When set HIGH a read operation is
selected, when set LOW, a write operation is selected.
DEVICE ADDRESSING
Following a start condition the master must output the
address of the slave it is accessing (see Figure 4). The
next two bits are the device select bits. A system could have
up to four X24645’s on the bus. The four
Following the start condition, the X24645 monitors the SDA
bus comparing the slave address being transmitted
with its slave address device type identifier. Upon a
correct compare the X24645 outputs an acknowledge on
addresses are defined by the state of the S1 and S2 inputs.
S2 of the slave address must be the inverse of
the S2 input pin.
the SDA line. Depending on the state of the R/W bit, the
X24645 will execute a read or write operation.
Figure 4. Slave Address
WRITE OPERATIONS
Byte Write
HIGH ORDER
ADDRESS
BITS
DEVICE
SELECT
For a write operation, the X24645 requires a second ad-
dress field. This address field is the byte address, com-
prised of eight bits, providing access to any one of 8192
words in the array. Upon receipt of the byte address, the
S
2
S
1
A10
A11
A12
A9
A8 R/W
X24645 responds with an acknowledge and awaits the
next eight bits of data, again responding with an acknowledge
2783 ILL F07.1
The master then terminates the transfer by generating a
The next five bits of the slave address are an extension of stop condition, at which time the X24645 begins
the array’s address and are concatenated with
the internal write cycle to the nonvolatile memory. While the
internal write cycle is in progress the X24645 inputs
the eight bits of address in the byte address field,
providing direct access to the whole 8192 x 8 array.
are disabled, and the device will not respond to any requests
from the master. Refer to Figure 5 for the address,
acknowledge and data transfer sequence.
Figure 5. Byte Write
S
T
S
T
O
P
SLAVE
ADDRESS
BYTE
ADDRESS
A
R
T
BUS ACTIVITY:
MASTER
DATA
SDA LINE
S
P
A
C
K
A
C
K
A
C
K
BUS ACTIVITY:
X24645
2783 ILL F08.1
5
X24645
Flow 1. ACK Polling Sequence
Page Write
The X24645 is capable of a 32-byte page write operation.
It is initiated in the same manner as the byte write
WRITE OPERATION
COMPLETED
ENTER ACK POLLING
operation, but instead of terminating the write cycle after
the first data word is transferred, the master can
transmit up to thirty-one more bytes. After the receipt of
each byte, the X24645 will respond with an acknowledge.
ISSUE
START
After the receipt of each byte, the five low order
address bits are internally incremented by one. The high
order eight bits of the address remain constant. If the
master should transmit more than 32 bytes prior to gen-
ISSUE SLAVE
ADDRESS AND R/W = 0
ISSUE STOP
erating the stop condition, the address counter will “roll
over” and the previously written data will be overwritten
As with the byte write operation, all inputs are disabled
until completion of the internal write cycle. Refer to
ACK
RETURNED?
NO
Figure 6 for the address, acknowledge, and data
transfer sequence.
YES
Acknowledge Polling
The Max Write Cycle Time can be significantly reduced
using Acknowledge Polling. To initiate Acknowledge
NEXT
OPERATION
A WRITE?
NO
Polling, the master issues a start condition followed by the
Slave Address Byte for a write or read operation. If
YES
the device is still busy with the high voltage cycle, then no
ACK will be returned. If the device has completed
ISSUE BYTE
ADDRESS
ISSUE STOP
PROCEED
the write operation, an ACK will be returned and the
host can then proceed with the read or write operation.
Refer to Flow 1.
PROCEED
2783 ILL F09
Figure 6. Page Write
S
T
S
T
O
P
SLAVE
ADDRESS
A
R
T
BUS ACTIVITY:
MASTER
BYTE ADDRESS (n)
DATA n
DATA n+1
DATA n+31
SDA LINE
S
P
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
BUS ACTIVITY:
X24645
2783 ILL F10.2
6
X24645
and transmits the byte. The read operation is terminated by
the master; by not responding with an acknowledge
READ OPERATIONS
Read operations are initiated in the same manner as write
operations with the exception that the R/W bit of
and by issuing a stop condition. Refer to Figure 7 for the
sequence of address, acknowledge and data transfer.
the slave address is set HIGH. There are three basic read
operations: current address read, random read
Random Read
Random read operations allow the master to access any
memory location in a random manner. Prior to issuing
and sequential read.
It should be noted that the ninth clock cycle of the read
operation is not a “don’t care.” To terminate a read
the slave address with the R/W bit set HIGH, the master must
first perform a “dummy” write operation.
operation, the master must either issue a stop condition
during the ninth cycle or hold SDA HIGH during the
ninth clock cycle and then issue a stop condition.
The master issues the start condition, and the slave ad-
dress with the R/W bit set LOW, followed by the byte
address it is to read. After the word address acknowledge,
the master immediately reissues the start condition
Current Address Read
Internally the X24645 contains an address counter that
maintains the address of the last byte read, increment-
and the slave address with the R/W bit set HIGH.
This will be followed by an acknowledge from the
X24645 and then by the data byte. The read operation is
terminated by the master; by not responding with an
acknowledge and by issuing a stop condition. Refer to
Figure 8 for the address, acknowledge and data
ed by one or the exact address of the last byte written.
Therefore, if the last access read was to address n, the
next read operation would access data from address
n + 1. Upon receipt of the slave address with the R/W
set HIGH, the X24645 issues an acknowledge
transfer sequence.
Figure 7. Current Address Read
S
T
A
R
T
S
T
O
P
SLAVE
ADDRESS
BUS ACTIVITY:
MASTER
SDA LINE
S
P
A
C
BUS ACTIVITY:
X24645
DATA
K
2783 ILL F11
Figure 8. Random Read
S
S
T
A
R
T
T
A
R
T
S
T
O
P
SLAVE
ADDRESS
BYTE
ADDRESS n
SLAVE
ADDRESS
BUS ACTIVITY:
MASTER
SDA LINE
S
S
P
A
C
K
A
C
K
A
C
K
BUS ACTIVITY:
X24645
DATA n
2783 ILL F12.1
7
X24645
The data output is sequential, with the data from
address n followed by the data from n + 1. The address
Sequential Read
Sequential reads can be initiated as either a current
address read or random access read. The first byte is
counter for read operations increments all address bits,
allowing the entire memory contents to be serially read
transmitted as with the other modes, however, the
master now responds with an acknowledge, indicating
during one operation. At the end of the address space
(address 8191), the counter “rolls over” to 0 and the
it requires additional data. The X24645 continues to
output data for each acknowledge received. The read
X24645 continues to output data for each acknowledge
received. Refer to Figure 9 for the address,
operation is terminated by the master; by not responding
with an acknowledge and then issuing a
stop condition.
acknowledge and data transfer sequence.
Figure 9. Sequential Read
S
SLAVE
ADDRESS
A
C
K
A
C
K
A
C
K
T
O
P
BUS ACTIVITY:
MASTER
SDA LINE
P
A
C
K
BUS ACTIVITY:
X24645
DATA n
DATA n+1
DATA n+2
DATA n+x
2783 ILL F13
Figure 10. Typical System Configuration
V
CC
PULL-UP
RESISTORS
SDA
SCL
MASTER
SLAVE
SLAVE
TRANSMITTER/
RECEIVER
MASTER
TRANSMITTER/
RECEIVER
MASTER
TRANSMITTER
TRANSMITTER/
RECEIVER
RECEIVER
2783 ILL F14
8
X24645
WEL and RWEL are volatile latches that power-up in the
LOW (disabled) state. A write to any address other
WRITE PROTECT REGISTER
The Write Protect Register (WPR) is located at the
highest address, 1FFFh.
than 1FFFh, where the Write Protect Register is
located, will be ignored (no ack) until the WEL bit is set
Figure 11. Write Protect Register
HIGH. The WEL bit is set by writing 0000001x to
address 1FFFh. Once set, WEL remains HIGH until
WPR (ADDR = 1FFFh)
either reset (by writing 00000000 to 1FFFh) or until the part
powers-up again. The RWEL bit controls writes to
7
6
5
4
3
1
0
2
the block protect bits. RWEL is set by first setting WEL to
“1”
WPEN
0
0
BP1
BP0
WEL
0
RWEL
and then writing 0000011x to address 1FFFh.
RWEL must be set in order to change the block protect bits,
BP0 and BP1, or the WPEN bit. RWEL is reset
2783 ILL F15.1
WPR.1 = WEL
–- “Write Enable” Latch (Volatile)
when the block protect or WPEN bits are changed, or
when the part powers-up again.
0 = Write enable latch reset, writes disabled 1 =
Write enable latch set, writes enabled
Programming the BP or WPEN Bits
A three step sequence is required to change the
nonvolatile Block Protect or Write Protect Enable:
If WEL = “0”then “no ACK” after first byte of input data.
WPR.2 = RWEL
–-
1) Set WEL = 1 (write 00000010 to address 1FFFh,
volatile write cycle)
“Register Write Enable” Latch (Volatile)
0 = Register write enable latch reset, writes dis-
abled
(Start)
1 = Register write enable latch set, writes enabled
2) Set RWEL = 1 (write 00000110 to address 1FFFh,
volatile write cycle)
WPR.3, WPR.4 = BP0, BP1
–- Block Protect Bits (Nonvolatile)
(See Block Protect section for definition)
(Start)
3) Set BP1, BP0, and/or WPEN bits (Write w00yz010 to
address 1FFFh)
WPR.7 = WPEN
- Write Protect Enable Bit (Nonvolatile)
(See Hardware Write Protect section for definition)
w = WPEN, y = BP1, Z = BP0,
(Stop)
Writing to the Write Protect Register
The Write Protect Register is written by performing a
random write of one byte directly to address, 1FFFh. If
Step 3 is a nonvolatile write cycle, requiring 10ms to
complete. RWEL is reset to “0”
a page write is performed starting with any address other
than 1FFF, the byte in the array at address
by this write cycle,
requiring another write cycle to set RWEL again before
the block protect bits can be changed. RWEL must be
1FFFh will be written instead of the Write Protect
Register (assuming writes are not disabled by the
block protect register).
“0
”
in step 3; if w00yz110 is written to address 1FFFh,
RWEL is set but WPEN, BP1 and BP0 are not
changed (the device remains at step 2).
The state of the Write Protect Register can be read by
performing a random read at address 1FFFh at any
time. If a sequential read starting at any other address than
1FFFh is performed, the contents of the byte in
the array at 1FFFh is read out instead of the Write
Protect Register.
9
X24645
Block Protect Bits
The Block Protect Bits BP0 and BP1 determine which
blocks of the memory are write-protected:
Programmable Hardware Write Protect
The Write Protect (WP) pin and the Write Protect Enable
(WPEN) bit in the Write Protect Register
control the programmable hardware write protect feature.
Hardware write protection is enabled when the
Table 1. Block Protect Bits
WP pin is HIGH and the WPEN bit is “1”, and disabled
when either the WP pin is LOW or the WPEN bit is “0”.
Protected
BP1 BP0 Addresses
When the chip is hardware write-protected, nonvolatile writes
are disabled to the Write Protect Register,
0
0
1
0
1
0
None
including the BP bits and the WPEN bit itself, as well as to
block-protected sections in the memory array.
1800h–1FFFh
1000h–1FFFh
Upper 1/4
Upper 1/2
Only the sections of the memory array that are not
block-protected can be written. Note that since the
Full Array (WPR
not included)
1
1
0000h–1FFFh
WPEN bit is write-protected, it cannot be changed back
to a LOW state, and write protection is disabled
2783 FRM T02
as long as the the WP pin is held HIGH. Table 2
defines the write protection status for each state of
WPEN and WP.
Table 2. Write Protect Status Table
Memory Array
Memory Array
(Block Protected)
(Not Block
Protected)
WP
L
WPEN
BP Bits
Writable
Writable
Protected
WPEN Bit
Writable
X
0
1
Writable
Writable
Writable
Protected
X
Protected
Writable
H
Protected
Protected
2783 FRM T03.1
10
X24645
ABSOLUTE MAXIMUM RATINGS*
Temperature under Bias
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This
is a stress rating only and the functional operation
X24645.......................................–65°C to +135°C
Storage Temperature........................–65°C to +150°C
Voltage on any Pin with
of the device at these or any other conditions above
those indicated in the operational sections of this
Respect to VSS .................................... –1V to +7V
D.C. Output Current ..............................................5mA
Lead Temperature (Soldering,
specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
..............................300°C
10 seconds)
affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Supply Voltage
X24645
Limits
Temperature
Commercial
Industrial
Min.
0°C
Max.
+70°C
+85°C
+125°C
4.5V to 5.5V
2.7V to 5.5V
X24645-2.7
–40°C
–55°C
2783 FRM T05
Military
2783 FRM T04
D.C. OPERATING CHARACTERISTICS
Limits
Max.
Symbol
Parameter
Min.
Units
Test Conditions
ICC1
VCC Supply Current (Read)
1
3
mA
SCL = VCC X 0.1/VCC X 0.9 Levels @
100KHz, SDA = Open, All Other
Inputs = VSS or VCC – 0.3V
ICC2
VCC Supply Current (Write)
VCC Standby Current
mA
∝A
(1)
50
SCL = SDA = VCC, All Other
Inputs = VSS or VCC – 0.3V,
VCC = 5V 10%
ISB1
∝A
(1)
VCC Standby Current
SCL = SDA = VCC, All Other
Inputs = VSS or VCC – 0.3V,
VCC = 2.7V
1
ISB2
∝A
∝A
ILI
VIN = VSS to VCC
VOUT = VSS to VCC
Input Leakage Current
Output Leakage Current
Input LOW Voltage
10
10
ILO
(2)
VCC x 0.3
–1
V
V
V
VlL
(2)
VCC x 0.7 VCC + 0.5
0.4
Input HIGH Voltage
Output LOW Voltage
VIH
VOL
IOL = 3mA, VCC = 4.5V
2783 FRM T06.2
CAPACITANCE TA = +25°C, f = 1MHz, VCC = 5V
Symbol
Parameter
Max.
Units
Test Conditions
(3)
VI/O = 0V
Input/Output Capacitance (SDA)
8
pF
CI/O
(3)
VIN = 0V
Input Capacitance (S1, S2, SCL)
6
pF
CIN
2783 FRM T07.1
Notes: (1)Must perform a stop command prior to measurement.
(2)VIL min. and VIH max. are for reference only and are not 100% tested. (3)This
parameter is periodically sampled and not 100% tested.
11
X24645
EQUIVALENT A.C. LOAD CIRCUIT
A.C. CONDITIONS OF TEST
VCC x 0.1 to VCC x 0.9
Input Pulse Levels
5V
Input Rise and
Fall Times
10ns
1.53KΟ
Input and Output
Timing Levels
OUTPUT
VCC X 0.5
2783 FRM T08
100pF
2783 ILL F16.1
A.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions, unless otherwise specified.) Read
& Write Cycle Limits
Symbol
Parameter
SCL Clock Frequency
Min.
Max.
100
Units
KHz
ns
fSCL
0
TI
100
Noise Suppression Time
Constant at SCL, SDA Inputs
∝s
∝s
tAA
SCL LOW to SDA Data Out Valid
0.3
4.7
3.5
tBUF
Time the Bus Must Be Free Before a
New Transmission Can Start
∝s
∝s
∝s
∝s
tHD:STA
tLOW
Start Condition Hold Time
Clock LOW Period
4
4.7
4
tHIGH
Clock HIGH Period
tSU:STA
4.7
Start Condition Setup Time (for
a Repeated Start Condition)
∝s
tHD:DAT
tSU:DAT
tR
Data In Hold Time
0
Data In Setup Time
250
ns
∝s
SDA and SCL Rise Time
SDA and SCL Fall Time
Stop Condition Setup Time
Data Out Hold Time
1
tF
300
ns
∝s
tSU:STO
tDH
4.7
300
ns
2783 FRM T09.2
(4)
POWER-UP TIMING
Symbol
Parameter
Max.
Units
ms
tPUR
Power-up to Read Operation
Power-up to Write Operation
1
5
tPUW
ms
2783 FRM T10
Notes: (4)tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. These parameters are periodically
sampled and not 100% tested.
12
X24645
Bus Timing
t
t
t
t
HIGH
LOW
R
F
SCL
t
t
t
t
t
SU:STA
HD:STA
HD:DAT
SU:DAT
SU:STO
SDA IN
t
t
t
AA
DH
BUF
SDA OUT
2783 ILL F17
Write Cycle Limits
Symbol
(5)
Parameter
Write Cycle Time
Min.
Typ.
Max.
Units
(6)
TWR
5
10
ms
2783 FRM T11
The write cycle time is the time from a valid stop
condition of a write sequence to the end of the internal
X24645 bus interface circuits are disabled, SDA is
allowed to remain HIGH, and the device does not
erase/program cycle. During the write cycle, the
respond to its slave address.
Bus Timing
SCL
ACK
SDA
8th BIT
WORD n
t
WR
2783 ILL F18
STOP
CONDITION
START
CONDITION
Notes: (5)Typical values are for TA = 25°C and nominal supply voltage (5V).
(6)tWR is the minimum cycle time to be allowed from the system perspective unless polling techniques are used. It is the maximum
time the device requires to automatically complete the internal write operation.
SYMBOL TABLE
Guidelines for Calculating Typical Values of
Bus Pull-Up Resistors
WAVEFORM
INPUTS
OUTPUTS
120
V
CC MAX
Must be
steady
Will be
steady
R
=
=1.8KΟ
MIN
I
100
80
OL MIN
t
R
R
May change
from LOW
to HIGH
Will change
from LOW
to HIGH
=
MAX
C
BUS
MAX.
RESISTANCE
60
40
20
0
May change
from HIGH
to LOW
Will change
from HIGH
to LOW
MIN.
RESISTANCE
Don’t Care:
Changes
Allowed
Changing:
State Not
Known
20 40 60 80100120
BUS CAPACITANCE (pF)
0
N/A
Center Line
is High
Impedance
2783 ILL F19
13
X24645
PACKAGING INFORMATION
8-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P
0.430 (10.92)
0.360 (9.14)
0.260 (6.60)
0.240 (6.10)
PIN 1 INDEX
PIN 1
0.300
(7.62) REF.
0.060 (1.52)
0.020 (0.51)
HALF SHOULDER WIDTH ON
ALL END PINS OPTIONAL
0.145 (3.68)
0.128 (3.25)
SEATING
PLANE
0.025 (0.64)
0.015 (0.38)
0.150 (3.81)
0.125 (3.18)
0.065 (1.65)
0.045 (1.14)
0.110 (2.79)
0.090 (2.29)
0.020 (0.51)
0.016 (0.41)
0.325 (8.25)
0.300 (7.62)
0.015 (0.38)
MAX.
0°
15°
TYP. 0.010 (0.25)
NOTE:
1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2.
PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH
3926 FHD F01
14
X24645
PACKAGING INFORMATION
8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S
0.150 (3.80)
0.158 (4.00)
0.228 (5.80)
0.244 (6.20)
PIN 1 INDEX
PIN 1
0.014 (0.35)
0.019 (0.49)
0.188 (4.78)
0.197 (5.00)
(4X) 7°
0.053 (1.35)
0.069 (1.75)
0.004 (0.19)
0.010 (0.25)
0.050 (1.27)
0.050" TYPICAL
0.010 (0.25)
0.020 (0.50)
X 45°
0.050"
TYPICAL
0° – 8°
0.0075 (0.19)
0.010 (0.25)
0.250"
0.016 (0.410)
0.037 (0.937)
0.030"
TYPICAL
8 PLACES
FOOTPRINT
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
3926 FHD F22.1
15
X24645
PACKAGING INFORMATION
14-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S
0.150 (3.80)
0.158 (4.00)
0.228 (5.80)
0.244 (6.20)
PIN 1 INDEX
PIN 1
0.014 (0.35)
0.020 (0.51)
0.336 (8.55)
0.345 (8.75)
(4X) 7°
0.053 (1.35)
0.069 (1.75)
0.004 (0.10)
0.010 (0.25)
0.050 (1.27)
0.050" Typical
0.010 (0.25)
0.020 (0.50)
X 45°
0° – 8°
0.050" Typical
0.0075 (0.19)
0.010 (0.25)
0.250"
0.016 (0.41)
0.037 (0.937)
0.030" Typical
14 Places
FOOTPRINT
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
3926 FHD F10.1
16
X24645
PACKAGING INFORMATION
20-LEAD PLASTIC, TSSOP PACKAGE TYPE V
.025 (.65) BSC
.169
(4.3) .177
(4.5)
.252 (6.4) BSC
.252
(6.4) .300
(6.6)
.047 (1.20)
.0075
.002
(.19) .0118
(.05) .006
(.30)
(.15)
.010 (.25)
Gage Plane
0° – 8°
Seating Plane
.019
(.50) .029
(.75)
Detail A (20X)
.031
(.80) .041
(1.05)
See Detail “A”
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
3926 FHD F45
17
X24645
ORDERING INFORMATION
X24645
P
T
G -V VCC Range
Blank = 5V 10%
2.7 = 2.7V to 5.5V
Device
G = RoHS Compliant Lead Free package
Blank = Standard package. Non lead free
Temperature Range
Blank = 0°C to +70°C
I = –40°C to +85°C
M = –55°C to +125°C
Package
P = 8-Lead Plastic DIP
S8 = 8-Lead SOIC (JEDEC)
S = 14-Lead SOIC
V = 20-Lead TSSOP
Part Mark Convention
X24645
XG
X
P = 8-Lead Plastic DIP
S = 14-Lead SOIC
Blank = 8-Lead SOIC (JEDEC)
V = 20-Lead TSSOP
G = RoHS compliant lead free
Blank = 4.5V to 5.5V, 0°C to +70°C
I = 4.5V to 5.5V, –40°C to +85°C
F = 2.7V to 5.5V, 0°C to +70°C
G = 2.7V to 5.5V, –40°C to +85°C
LIMITED WARRANTY
Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no
warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from
patent infringement. Xicor, Inc. makes no warranty of merchantability or fitness for any purpose. Xicor, Inc. reserves the right to discontinue production
and change specifications and prices at any time and without notice.
Xicor, Inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a Xicor, Inc. product. No other circuits, patents, licenses
are implied.
U.S. PATENTS
Xicor products are covered by one or more of the following U.S. Patents: 4,263,664; 4,274,012; 4,300,212; 4,314,265; 4,326,134; 4,393,481; 4,404,475;
4,450,402; 4,486,769; 4,488,060; 4,520,461; 4,533,846; 4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829, 482; 4,874, 967; 4,883, 976. Foreign
patents and additional patents pending.
LIFE RELATED POLICY
In situations where semiconductor component failure may endanger life, system designers using this product should design the system with
appropriate error detection and correction, redundancy and back-up features to prevent such an occurence.
Xicor's products are not authorized for use in critical components in life support devices or systems.
1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain
life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected
to result in a significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of
the life support device or system, or to affect its safety or effectiveness.
18
相关型号:
©2020 ICPDF网 联系我们和版权申明