G570 [GMT]
Dual-Slot PCMCIA/CardBus Power Controller; 双槽PCMCIA / CardBus的电源控制器型号: | G570 |
厂家: | GLOBAL MIXED-MODE TECHNOLOGY INC |
描述: | Dual-Slot PCMCIA/CardBus Power Controller |
文件: | 总14页 (文件大小:219K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Global Mixed-mode Technology Inc.
G570
Dual-Slot PCMCIA/CardBus Power Controller
Features
Description
ꢀFully Integrated VCC and Vpp Switching for Dual
The G570 PC Card power-interface switch provides an
integrated power-management solution for two PC
Cards. All of the discrete power MOSFETs, a logic
section, current limiting, and thermal protection for PC
Card control are combined on a single integrated cir-
cuit (IC). The circuit allows the distribution of 3.3V, 5V,
and/or 12V card power by means of the Serial inter-
face. The current-limiting feature eliminates the need
for fuses, which reduces component count and im-
proves reliability.
Slot PC CardTM Interface
ꢀ3-Lead Serial Interface Compatible With
CardBusTM Controllers
ꢀ3.3V Low Voltage Mode
ꢀMeets PC Card Standards
ꢀRESET for System Initialization of PC Cards
ꢀ12V Supply Can Be Disabled Except During
12V Flash Programming
ꢀShort Circuit and Thermal Protection
ꢀ28 Pin and 30 Pin SSOP
The G570 features a 3.3V low voltage mode that allows
for 3.3V switching without the need for 5V supply. This
facilitates low power system designs such as sleep
mode and pager mode where only 3.3V is available.
The G570 incorporates a reset function, selectable by
one of two inputs, to help alleviate system errors. The
reset function enables PC card initialization concurrent
with host platform initialization, allowing a system reset.
Reset is accomplished by grounding the VCC and VPP
(flash-memory programming voltage) outputs, which
discharges residual card voltage.
ꢀCompatible With 3.3V, 5V and 12V PC Cards
ꢀLow RDS(on) (225-mΩ 5V VCC Switch;
200 mΩ 3.3V VCC Switch)
ꢀBreak-Before-Make Switching
ꢀInternal power-On Reset
Application
ꢀNotebook PC
ꢀElectronic Dictionary
ꢀPersonal Digital Assistance
ꢀDigital still Camera
End equipment for the G570 includes notebook com-
puters, desktop computers, personal digital assistants
(PDAs), digital cameras and bar-code scanners.
Ordering Information
PART NUMBER TEMP. RANGE
PACKAGE
28 SSOP
G570S4
G570SA
-40°C to +85°C
-40°C to +85°C
30 SSOP
Pin Information
G570
G570
5V
1
2
3
4
5V
30
29
5V
DATA
1
2
5V
5V
28
27
26
25
24
NC
5V
DATA
28 NC
3
4
NC
NC
NC
CLOCK
LATCH
CLOCK
LATCH
RESET
12V
NC
NC
27
26
5
6
7
8
9
5
6
RESET
12V
25 NC
23 12V
12V
24
23
AVPP
22 BVPP
7
8
9
BVPP
BVCC
AVPP
AVCC
AVCC
AVCC
BVCC
21
AVCC
AVCC
AVCC
GND
NC
22
20
BVCC
21 BVCC
10
11
19 BVCC
10
11
20
BVCC
18
NC
GND 12
NC
19
18
17
16
12
13
14
17
OC
13
14
NC
OC
16
RESET
3.3V
3.3V
3.3V
15
3.3V
3.3V
RESET
3.3V 15
28Pin SSOP
30Pin SSOP
Ver 1.0
Nov 09, 2000
TEL: 886-3-5788833
http://www.gmt.com.tw
1
Global Mixed-mode Technology Inc.
G570
Output current (each card):
Absolute maximum ratings over operating
I
I
O (xVCC)……………………..……...…..internally limited
O(xVPP)...............................…........... internally limited
(unless otherwise noted)*
Input voltage range for card power:
free-air temperature
Operating virtual junction temperature range, TJ
……………………………………………….-40°C to 150°C
Operating free-air temperature range, TA
...…………………….……..……………….-40°C to 85°C
Storage temperature range, TSTG….…...-55°C to 150°C
V
V
V
I(3.3V).................................………………-0.3V to 7V
I(5V)........................………..…...………..-0.3V to 7V
I(12V) ...................………..…………….. -0.3V to 14V
Logic input voltage...................................…-0.3V to 7V
*Stresses beyond those listed under "absolute maximum ratings”may cause permanent damage to the device. These are stress rating
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions”is not implied. Exposure to absolute–maximum-rated conditions for extended periods may affect device reliability.
Recommended Operating Conditions
Min
Max
5.25
5.25
13.5
1
Unit
V
VI (5V)
0
0
0
Input voltage range, VI
VI (3.3V)
V
VI (12V)
V
IO (xVCC) at 25°C
A
Output current
I
O (xVPP) at 25°C
150
2.5
mA
MHz
°C
Clock frequency
0
Operating virtual junction temperature, TJ
-40
125
Typical PC Card Power-Distribution Application
Power Supply
G570
VPP1
VPP2
VCC
VCC
AVPP
12V
5V
12V
5V
PC Card A
PC Card B
AVCC
AVCC
AVCC
3.3V
3.3V
RESET
RESET
Supervisor
VPP1
VPP2
VCC
VCC
BVPP
BVCC
3
Serial Interface
OC
PCMCIA
Controller
BVCC
BVCC
Ver 1.0
Nov 09, 2000
TEL: 886-3-5788833
http://www.gmt.com.tw
2
Global Mixed-mode Technology Inc.
G570
Terminal Functions
28 Pin
TERMINAL
I/O
DESCRIPTION
NAME
3.3V
NO.
14,15,16
I
I
3.3V VCC input for card power
5V
1,27,28
5V VCC input for card power and/or chip power
12V VPP input for card power
12V
6,23
I
AVCC
AVPP
BVCC
BVPP
CLOCK
DATA
GND
8,9,10
O
O
O
O
I
Switched output that delivers 0V,3.3V,5V or high impedance to card
Switched output that delivers 0V,3.3V,5V,12V or high impedance to card
Switched output that delivers 0V, 3.3V, 5V or high impedance
Switch output that delivers 0V, 3.3V, 5V, 12V or high impedance
Logic-level clock for serial data word
7
19,20,21
22
3
2
I
Logic-level serial data word
11
Ground
LATCH
NC
4
I
Logic level latch for serial data word
12,18,24,25,26
No internal connection
Logic-level overcurrent. OC reports output that goes low when an overcurrent condition
exists
OC
17
O
RESET
RESET
5
I
I
Logic-level RESET input active high. Do not connect if terminal 13 is used.
13
Logic-level
input active low. Do not connect if terminal 5 is used.
RESET
30 Pin
NAME
TERMINAL
I/O
DESCRIPTION
NO.
3.3V
15,16,17
I
I
3.3V VCC input for card power
5V
1,2,30
5V VCC input for card power and/or chip power
12V VPP input for card power
12V
7,24
I
AVCC
AVPP
BVCC
BVPP
CLOCK
DATA
GND
9,10,11
O
O
O
O
I
Switched output that delivers 0V,3.3V,5V or high impedance to card
Switched output that delivers 0V,3.3V,5V,12V or high impedance to card
Switched output that delivers 0V, 3.3V, 5V or high impedance
Switch output that delivers 0V, 3.3V, 5V, 12V or high impedance
Logic level clock for serial data word
8
20,21,22
23
4
3
12
I
Logic level serial data word
Ground
LATCH
5
I
Logic level latch for serial data word
13,19,25,26,
27,28,29
NC
OC
No internal connection
Logic-level overcurrent. OC reports output that goes low when an overcurrent condition
exists
18
O
RESET
RESET
6
I
I
Logic-level RESET input active high. Do not connect if terminal 14 is used.
Logic-level RESET input active low. Do not connect if terminal 6 is used.
14
Ver 1.0
TEL: 886-3-5788833
Nov 09, 2000
http://www.gmt.com.tw
3
Global Mixed-mode Technology Inc.
G570
(T = 25°C, VI(5V) = 5V; unless otherwise noted)
Electrical Characteristics
A
DC Characteristics
PARAMETER
TEST CONDITIONS
MIN TYP MAX UNIT
5V to x VCC
3.3V to x VCC
3.3V to x VCC
5V to x VPP
170
140
150
225
200
200
6
mΩ
VI(5V) = 5V, VI(3.3V) =3.3V
VI(5V) = 0V, VI(3.3V) =3.3V
Switch resistance*
Ω
3.3V to x VPP
12V to x VPP
6
6
VO(xVPP) Clamp low voltage
VO(xVCC) Clamp low voltage
IPP at 10mA
ICC at 10mA
0.8
0.8
10
10
V
V
IPP high impedance State TA = 25°C
CC high-impedance State TA = 25°C
1
1
IIKG Leakage current
µA
I
VI(5V) = 5V
VO(AVCC) = VO(BVCC) = 5V
115
131
2
150
150
V
O(AVPP) = VO(BVPP) = 12V
O(AVCC) = VO(BVCC) = 3.3V
VI(5V) = 0V
V
II
Input current
µA
VI(3.3V) = 3.3V
Shutdown mode
VO(AVPP) = VO(BVPP) = 0V
O(BVCC) = VO(AVCC)
V
=VO(AVPP) = VO(BVPP) = Hi-Z
Output powered up into a short to
GND
IOS Short-circuit
IO(xVCC)
IO(xVPP)
0.8
2.2
A
Output current Limit
120
400
mA
*Pulse-testing techniques are used to maintain junction temperature close to ambient temperatures; thermal effects must be taken into account
separately.
Logic Section
PARAMETER
TEST CONDITION
MIN
2
MAX
UNIT
µA
V
Logic input current
1
Logic input high level
Logic input low level
0.8
0.4
V
V
I(5V)-0.4
VI(5V) = 5V, IO = 1mA
VI(5V) = 0V, IO = 1mA
I(3.3V)= 3.3V
IO = 1mA
Logic output high level
Logic output low level
V
V
V
I(3.3V)-0.4
V
Switching Characteristics *, **
PARAMETER
TEST CONDITION
MIN
TYP
2
MAX
UNIT
VO (xVCC)
tr Output rise time
VO (xVPP)
VO (xVCC)
VO (xVPP)
10
16
45
7
ms
tf Output fall time
ton
toff
ton
toff
ton
toff
ton
toff
ms
ms
ms
ms
ms
ms
ms
ms
LATCH↑to VO(xVPP)
30
5
LATCH↑to VO(xVCC) (3.3V), VI(5V) = 5V
LATCH↑to VO(xVCC) (5V)
Propagation delay (see
16
3.2
25
6
tpd
Figure 1)
LATCH↑to VO(xVCC) (3.3V), VI(5V) = 0V
21
* Refer to Parameter Measurement Information
**Switching Characteristics are with CL = 147µF
Ver 1.0
Nov 09, 2000
TEL: 886-3-5788833
http://www.gmt.com.tw
4
Global Mixed-mode Technology Inc.
G570
Parameter Measurement Information
VPP
VCC
CL
CL
LOAD CIRCUIT
LOAD CIRCUIT
VDD
VDD
50%
50%
LATCH
GND
LATCH
GND
toff
toff
ton
ton
VI(12V)
GND
VI(5V)
VO(xVPP)
VO(xVCC)
90%
90%
10%
10%
GND
VOLTAGE WAVEFORMS
VOLTAGE WAVEFORMS
Figure 1. Test Circuits and Voltage Waveforms
Table of Timing Diagrams
D8
D7
D6
D5
D4
D3
D2
D1
D0
DATA
LATCH
CLOCK
Note:Data is clocked in on the positive leading edge of the clock. The latch should occur before the next
positive leading edge of the clock. For definition of D0 to D8, see the control logic table.
Figure 2. Serial-Interface Timing
Ver 1.0
Nov 09, 2000
TEL: 886-3-5788833
http://www.gmt.com.tw
5
Global Mixed-mode Technology Inc.
G570
Switching Characteristics
Switching Characteristics
Ver 1.0
Nov 09, 2000
TEL: 886-3-5788833
http://www.gmt.com.tw
6
Global Mixed-mode Technology Inc.
G570
Switching Characteristics
Ver 1.0
Nov 09, 2000
TEL: 886-3-5788833
http://www.gmt.com.tw
7
Global Mixed-mode Technology Inc.
G570
resistance of the switch and thus produce no addi-
tional voltage losses. Second, when an overcurrent
condition is detected, the G570 asserts a signal at
Application Information
Overview
PC Cards were initially introduced as a means to add
EEPROM (flash memory) to portable computers with
limited on-board memory. The idea of add-in cards
quickly took hold; modems, wireless LANs, Global
Positioning Satellite (GPS), multimedia, and hard-disk
versions were soon available. As the number of PC
Card applications grew, the engineering community
quickly recognized the need for a standard to ensure
compatibility across platforms. To this end, the
PCMCIA was established, comprised of members
from leading computer, software, PC Card, and
semiconductor manufactures. One key goal was to
realize the “plug-and play” concept. Cards and hosts
from different vendors should be compatible—able to
OC that can be monitored by the microprocessor to
initiate diagnostics and/or send the user a warning
message. In the event that an overcurrent condition
persists, causing the IC to exceed its maximum
junction temperature, thermal-protection circuitry
activates, shutting down all power outputs until the
device cools to within a safe operating region.
12V Supply Not Required
Most PC Card switches use the externally supplied
12V VPP power for switch-gate drive and other chip
functions, which requires that power be present at all
times. The G570 offers considerable power savings by
using an internal charge pump to generate the re-
quired higher voltages from 5V or 3.3V input; therefore,
the external 12V supply can be disable except when
needed for flash-memory functions, thereby extending
battery lifetime. Do not ground the 12V input if the 12V
input is not used. Additional power savings are real-
ized by the G570 during a software shutdown in which
quiescent current drops to a typical of 2µA.
communicate with one another transparently.
PC Card Power Specification
System compatibility also means power compatibility.
The most current set of specifications (PC Card Stan-
dard) set forth by the PCMCIA committee states that
power is to be transferred between the host and the
card through eight of the 68 terminals of the PC Card
connector. This power interface consists of two VCC,
two VPP, and four ground terminals. Multiple VCC and
ground terminals minimize connector-terminal and line
resistance. The two VPP terminals were originally
specified as separate signals but are commonly tied
together in the host to form a single node to minimize
voltage losses. Card primary power is supplied
through the VCC terminals; flash-memory programming
and erase voltage is supplied through the VPP termi-
nals.
3.3V Low Voltage Mode
The G570 operates in 3.3V low voltage mode when
3.3V is the only available input voltage (VI(5V)=0).This
allows host and PC Cards to be operated in low power
3.3V only modes such as sleep modes or pager
modes. Note that in this operation mode, the G570
derives its bias current from the 3.3V input pin and
only 3.3V can be delivered to the Card. The 3.3V
switch resistance increases, but the added switch re-
sistance should not be critical, because only a small
amount of current is delivered in this mode.
Overcurrent and Over-Temperature Protection
PC Cards are inherently subject to damage that can
result from mishandling. Host systems require protec-
tion against short-circuited cards that could lead to
power supply or PCB-trace damage. Even systems
robust enough to withstand a short circuit would still
undergo rapid battery discharge into the damaged PC
Card, resulting in the rather sudden and unacceptable
loss of system power. Most hosts include fuses for
protection. However, the reliability of fused systems is
poor, as blown fuses require troubleshooting and re-
pair, usually by the manufacturer.
Voltage Transitioning Requirement
PC Cards, like portables, are migrating from 5V to
3.3V to minimize power consumption, optimize board
space, and increase logic speeds. The G570 is de-
signed to meet all combinations of power delivery as
currently defined in the PCMCIA standard. The latest
protocol accommodates mixed 3.3V/5V systems by
first powering the card with 5V, then polling it to de-
termine its 3.3V compatibility. The PCMCIA specifica-
tion requires that the capacitors on 3.3V compatible
cards be discharged to below 0.8 V before applying
3.3V power. This ensures that sensitive 3.3V circuitry
is not subjected to any residual 5V charge and func-
tions as a power reset. The G570 offer a selectable
The G570 takes a two-pronged approach to overcur-
rent protection. First, instead of fuses, sense FETs
monitor each of the power outputs. Excessive current
generates an error signal that linearly limits the output
current, preventing host damage or failure. Sense
FETs, unlike sense resistors or polyfuses, have an
added advantage in that they do not add to the series
V
CC and VPP ground state, in accordance with PCMCIA
3.3V/5V switching specifications, to fully discharge the
card capacitors while switching between VCC voltage.
Ver 1.0
Nov 09, 2000
TEL: 886-3-5788833
http://www.gmt.com.tw
8
Global Mixed-mode Technology Inc.
G570
Output Ground Switches
RESET or RESET Inputs
Several PCMCIA power distribution switches on the
market do not have an active grounding FET switch.
These devices do not meet the PC Card specification
requiring a discharge of VCC within 100ms. PC Card
resistance can not be relied on to provide a discharge
path for voltages stored on PC Card capacitance be-
cause of possible high impedance isolation by power
management schemes. A method commonly shown to
alleviate this problem is to add to the switch output an
external 100kΩ resistor in parallel with the PC Card.
To ensure that cards are in a known state after power
brownouts or system initialization, the PC Cards
should be reset at the same time as the host by ap-
plying a low impedance to the VCC and VPP terminals.
A low impedance output state allows discharging of
residual voltage remaining on PC Card filter capaci-
tance, permitting the system (host and PC Cards) to
be powered up concurrently. The RESET or RESET
input closes internal switches S1, S4, S7, and S10
with all other switches left open (see G570 control
logic table). The G570 remains in the low impedance
output state until the signal is deasserted and further
Considering that this is the only discharge path to
ground, a timing analysis show that the RC time con-
stant delays the required discharge time to more than
2 seconds. The only way to ensure timing compatibility
with PC Card standards is to use a power-distribution
switch that has an internal ground switch, like that of
the G570, or add an external ground FET to each of
the output lines with the control logic necessary to se-
lect it.
data is clocked in and latched. RESET or RESET is
provided for direct compatibility with systems that use
either an active-low or active-high reset voltage super-
visor. The unused pin is internally pulled up or down
and should be left unconnected.
Overcurrent and Thermal Protection
The G570 uses sense FETs to check for overcurrent
conditions in each of the VCC and VPP outputs. Unlike
sense resistors or polyfuses, these FETs do not add to
the series resistance of the switch; therefore, voltage
and power losses are reduced. Overcurrent sensing is
applied to each output separately. When an overcur-
rent condition is detected, only the power output af-
fected is limited; all other power outputs continue to
function normally. The OC indicator, normally a logic
high, is a logic low when any overcurrent condition is
detected, providing for initiation of system diagnostics
and/or sending a warning message to the user.
In summary, the G570 is a complete single-chip
dual-slot PC Card power interface. It meets all cur-
rently defined PCMCIA specifications for power deliv-
ery in 5V, 3.3V, and mixed systems, and offers a serial
control interface. The G570 offers functionality, power
savings, overcurrent and thermal protection, and fault
reporting in one 30 pin SSOP surface-mount package
for maximum value added to new portable designs.
Power Supply Considerations
The G570 has multiple pins for each of its 3.3V, 5V,
and 12V power inputs and for switched VCC outputs.
Any individual pin can conduct the rated input or out-
put current. Unless all pins are connected in parallel,
the series resistance is significantly higher than that
specified, resulting in increased voltage drops and lost
power. Both 12V inputs must be connected for proper
VPP switching; it is recommended that all input and
output power pins be paralleled for optimum operation.
During power up, the G570 controls the rise time of
the VCC and VPP outputs and limits the current into a
faulty card or connector. If a short circuit is applied
after power is established (e.g., hot insertion of a bad
card), current is initially limited only by the impedance
between the short and the power supply. In extreme
cases, as much as 10A to 15A may flow into the short
before the current limiting of the G570 engages. If the
VCC or VPP outputs are driven below ground, the G570
may latch nondestructively in an off state. Cycling
power will reestablish normal operation.
Although the G570 is fairly immune to power input
fluctuations and noise, it is generally considered good
design practice to bypass power supplies typically with
a 1µF electrolytic or tantalum capacitor paralleled by a
0.047µF to 0.1µF ceramic capacitor. It is strongly re-
commended that the switched VCC and VPP outputs be
bypassed with a 0.1µF or larger capacitor; doing so
improves the immunity of the G570 to electrostatic
discharge (ESD). Care should be taken to minimize
the inductance of PCB traces between the G570 and
the load. High switching currents can produce large
negative-voltage transients, which forward biases
substrate diodes, resulting in unpredictable perform-
ance. Similarly, no pin should be taken below –0.3V.
Overcurrent limiting for the VCC outputs is designed to
activate, if powered up, into a short in the range of
0.8A to 2.2A. The VPP outputs limit from 120mA to
400mA. The protection circuitry acts by linearly limiting
the current passing through the switch rather than ini-
tiating a full shutdown of the supply. Shutdown occurs
only during thermal limiting.
Thermal limiting prevents destruction of the IC from
overheating if the package power-dissipation ratings are
exceeded. Thermal limiting disables all power outputs
(both A and B slots) until the device has cooled.
Ver 1.0
Nov 09, 2000
TEL: 886-3-5788833
http://www.gmt.com.tw
9
Global Mixed-mode Technology Inc.
G570
Logic Input and Outputs
escent current to 2µA to conserve battery power.
The serial interface consists of DATA, CLOCK, and
LATCH leads. The data is clocked in on the positive
leading edge of the clock (see Figure 2). The 9-bit (D0
through D8) serial data word is loaded during the positive
edge of the latch signal. The latch signal should occur
before the next positive leading edge of the block.
The G570 serial interface is designed to be compatible
with serial-interface PCMCIA controllers and current
PCMCIA and Japan Electronic Industry Development
Association (JEIDA) standards.
An overcurrent output ( OC ) is provided to indicate an
overcurrent condition in any of the VCC or VPP outputs as
previously discussed.
The shutdown bit of the data word places all VCC and VPP
outputs in a high-impedance state and reduces chip qui-
G570
Card A
S7
VPP1
S8
VPP2
S9
S1
S2
VCC
S3
cs
VCC
3.3V
See Note A
cs
3.3V
3.3V
Card B
S4
cs
VCC
VCC
S5
S6
5V
S10
5V
VPP1
VPP2
S11
S12
5V
cs
12V
12V
See Note A
Internal
Current Monitor
RESET
Supervisor
Controller
CPU
RESET
DATA
CLOCK
LATCH
Thermal
Serial
Interface
}
OC
GND
NOTE:MOSFET switches S9 and S12 have a back-gate diode from the source to the drain.
Unused switch inputs should never be grounded.
Figure 3 Internal Switching Matrix
Ver 1.0
Nov 09, 2000
10
TEL: 886-3-5788833
http://www.gmt.com.tw
Global Mixed-mode Technology Inc.
G570
G570 control logic
AVPP
CONTROL SIGNALS
INTERNAL SWITCH SETTING
OUTPUT
D0 A_VPP_PGM
D1 A_VPP_VCC
S7
S8
S9
VAVPP
D8 SHDN
1
1
1
1
0
0
0
1
1
×
0
1
0
1
×
CLOSED
OPEN
OPEN
OPEN
OPEN
OPEN
CLOSED
OPEN
OPEN
OPEN
0V
VCC*
CLOSED
OPEN
VPP(12 V)
Hi-Z
OPEN
OPEN
OPEN
Hi-Z
BVPP
CONTROL SIGNALS
INTERNAL SWITCH SETTING
OUTPUT
D4 B_VPP_PGM
D5 B_VPP_VCC
S10
S11
S12
VBVPP
D8 SHDN
1
1
1
1
0
0
0
1
1
×
0
1
0
1
×
CLOSED
OPEN
OPEN
OPEN
OPEN
OPEN
CLOSED
OPEN
OPEN
OPEN
0V
VCC**
VPP(12V)
Hi-Z
CLOSED
OPEN
OPEN
OPEN
OPEN
Hi-Z
AVCC
CONTROL SIGNALS
INTERNAL SWITCH SETTING
OUTPUT
S1
S2
S3
VAVCC
D8 SHDN
D3 A _BCC3
D2 A _ VCC5
1
1
1
1
0
0
0
1
1
×
0
1
0
1
×
CLOSED
OPEN
OPEN
CLOSED
OPEN
OPEN
OPEN
0V
3.3V
5V
OPEN
CLOSED
OPEN
CLOSED
OPEN
OPEN
0V
OPEN
OPEN
Hi-Z
BVCC
CONTROL SIGNALS
INTERNAL SWITCH SETTING
OUTPUT
S4
S5
S6
VBVCC
D8 SHDN
D6B_ VCC3
D7B_ VCC5
1
1
1
1
0
0
0
1
1
×
0
1
0
1
×
CLOSED
OPEN
OPEN
CLOSED
OPEN
OPEN
OPEN
0V
3.3V
5V
OPEN
CLOSED
OPEN
CLOSED
OPEN
OPEN
0V
OPEN
OPEN
Hi-Z
*Output depends on AVCC
**Output depends on BVCC
Ver 1.0
Nov 09, 2000
TEL: 886-3-5788833
http://www.gmt.com.tw
11
Global Mixed-mode Technology Inc.
G570
puts can be exposed to potentially higher discharges
from the external environment through the PC Card
connector. Bypassing the outputs with 0.1µF capaci-
tors protects the devices from discharges up to 10 kV.
ESD Protection
All
ESD-protection circuitry designed to withstand a 2kV
human-body-model discharge as defined in
G570
inputs
and
outputs
incorporate
MIL-STD-883C, Method 3015. The VCC and VPP out-
AVCC
VCC
0.1µF
VCC
AVCC
12V
PC Card
Connector A
12V
AVCC
VPP1
VPP2
0.1µF
(Ceramic)
1µF
BVCC
12V
BVCC
BVCC
VCC
0.1µF
0.1µF
VCC
VPP1
VPP2
PC Card
Connector B
AVPP
AVPP
G570
5V
5V
5V
0.1µF
0.1µF
1µF
1µF
BVPP
BVPP
5V
(Ceramic)
0.1µF
3.3V
3.3V
3.3V
DATA
DATA
CLOCK
CLOCK
LATCH
3.3V
(Ceramic)
LATCH
System Voltage
Supervisor
or
RESET
RESET
PCMCIA
Controller
PCI Bus Reset
OC
To CPU
GND
CS
Shutdown Signal
From CPU
Figure 4. Detailed Interconnections and Capacitor Recommendations
Ver 1.0
TEL: 886-3-5788833
Nov 09, 2000
http://www.gmt.com.tw
12
Global Mixed-mode Technology Inc.
G570
G570 28Pin Package
L
E1
E
h x 4
5
°
D
A2
A
A1
C
0.004
SEATING PLANE
b
e
DIMENSION IN MM
NOM.
DIMENSION IN INCH
NOM.
SYMBOL
MIN.
MAX.
MIN.
MAX.
A
A1
A2
b
2.0
0.079
0.05
1.65
0.22
0.09
0.002
0.065
0.009
0.004
1.75
0.30
1.85
0.33
0.21
0.069
0.012
0.073
0.013
0.008
c
0.15
0.006
e
0.65 BASIC
10.20
7.80
0.026 BASIC
0.402
D
9.90
7.40
5.00
0.55
0
10.50
8.20
5.60
0.95
8
0.390
0.291
0.197
0.022
0
0.413
0.323
0.220
0.038
8
E
0.307
E1
L
5.30
0.209
0.75
0.030
θ
4
4
JEDEC
MO-150 (AH)
Ver 1.0
Nov 09, 2000
TEL: 886-3-5788833
http://www.gmt.com.tw
13
Global Mixed-mode Technology Inc.
G570
G570 30Pin Package
c
D
L1
L
E1
E
1.15
3.6
θ
A1
A
A2
e
b
Note:
1. Dimensional tolerance ±0.10mm
2. Plating thickness 5~15µm
3. Dimensions “D” does not include burrs, however dimension including protrusions or gate burrs
Shall be MAX. 0.20mm
4. Dimension “E1” does not include inter-lead flash or protrusion. Inter-lead flash or protrusion small not exceeds
0.25 per side.
DIMENSION IN MM
DIMENSION IN INCH
SYMBOL
MIN.
1.80
0.05
1.75
0.25
0.10
10.10
7.50
5.20
0.53
1.10
NOM.
1.90
0.10
1.80
0.30
0.15
10.15
-----
5.25
0.68
MAX.
2.00
0.15
1.85
0.35
0.20
10.20
7.90
5.30
0.83
1.30
MIN.
0.071
0.002
0.069
0.010
0.004
0.398
0.295
0.205
0.021
0.043
NOM.
0.075
0.004
0.071
0.012
0.006
0.400
-----
0.207
0.027
0.047
0.026BSC
4°
MAX.
0.079
.006
0.073
0.014
0.008
.402
0.311
0.209
0.033
0.051
A
A1
A2
b
C
D
E
E1
L1
L
e
θ
1.20
0.65 BSC
4°
1º
7º
1°
7°
Ver 1.0
Nov 09, 2000
TEL: 886-3-5788833
http://www.gmt.com.tw
14
相关型号:
©2020 ICPDF网 联系我们和版权申明