DSP56858E [FREESCALE]
16-bit Digital Signal Controllers; 16位数字信号控制器型号: | DSP56858E |
厂家: | Freescale |
描述: | 16-bit Digital Signal Controllers |
文件: | 总64页 (文件大小:1348K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
56858
Data Sheet
Technical Data
56800E
16-bit Digital Signal Controllers
DSP56858
Rev. 6
01/2007
freescale.com
DSP56858 General Description
• 120 MIPS at 120MHz
• Two (2) Serial Communication Interfaces (SCI)
• Serial Port Interface (SPI)
• 40K x 16-bit Program SRAM
• 24K x 16-bit Data SRAM
• 1K x 16-bit Boot ROM
• 8-bit Parallel Host Interface
• General Purpose 16-bit Quad Timer
• Access up to 2M words of program memory or 8M data
memory
• JTAG/Enhanced On-Chip Emulation (OnCE™) for
unobtrusive, real-time debugging
• Chip Select Logic for glue-less interface to ROM and
SRAM
• Computer Operating Properly (COP)/Watchdog Timer
• Time-of -Day (TOD)
• Six (6) independent channels of DMA
• 144 LQFP and 144 MAPBGA packages
• Up to 47 GPIO
• Two (2) Enhanced Synchronous Serial Interfaces
(ESSI)
V
V
8
V
V
SSA
V
V
SSIO
SS
DDA
DDIO
DD
6
14
2
12
8
JTAG/
Enhanced
OnCE
16-Bit
56800E Core
Program Controller
and
Hardware Looping Unit
Address
Generation Unit
Data ALU
Bit
16 x 16 + 36 → 36-Bit MAC
Three 16-bit Input Registers
Four 36-bit Accumulators
Manipulation
Unit
PAB
PDB
CDBR
CDBW
Memory
XDB2
XAB1
XAB2
Program Memory
40,960 x 16 SRAM
System Bus
Control
DMA
6 channel
Boot ROM
1024 x 16 ROM
PAB
PDB
Data Memory
24,576 x 16 SRAM
CDBR
CDBW
IPBus Bridge (IPBB)
Decoding
Peripherals
CLKO
POR
IPBus CLK
3
MODE A-C or
GPIOH0-H2
System
Integration
Module
COP/TOD CLK
RSTO
External Address
Bus Switch
A0-20 [20:0]
RESET
External Data
Bus Switch
External Bus
Interface Unit
D0-D15 [15:0]
EXTAL
XTAL
Clock
Generator
Time
of
Day
ESSI0
or
GPIOC
2 SCI
or
GPIOE
ESSI1
or
GPIOD
Quad
Timer
or
SPI
or
GPIOF
Host
Interrupt
COP/
Watch-
dog
RD Enable
WR Enable
Interface Controller
or
GPIOB
Bus Control
OSC PLL
GPIOG
CS0-CS3[3:0] or
GPIOA0-A3
6
4
6
4
4
16
IRQA
IRQB
56858 Block Diagram
56858 Technical Data, Rev. 6
Freescale Semiconductor
3
Part 1 Overview
1.1 56858 Features
1.1.1
Digital Signal Processing Core
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Efficient 16-bit engine with dual Harvard architecture
120 Million Instructions Per Second (MIPS) at 120MHz core frequency
Single-cycle 16 × 16-bit parallel Multiplier-Accumulator (MAC)
Four (4) 36-bit accumulators including extension bits
16-bit bidirectional shifter
Parallel instruction set with unique DSP addressing modes
Hardware DO and REP loops
Three (3) internal address buses and one (1) external address bus
Four (4) internal data buses and one (1) external data bus
Instruction set supports both DSP and controller functions
Four (4) hardware interrupt levels
Five (5) software interrupt levels
Controller-style addressing modes and instructions for compact code
Efficient C-Compiler and local variable support
Software subroutine and interrupt stack with depth limited only by memory
JTAG/Enhanced OnCE debug programming interface
1.1.2
Memory
•
Harvard architecture permits up to three (3) simultaneous accesses to program and data memory
•
On-Chip Memory
— 40K × 16-bit Program RAM
— 24K × 16-bit Data RAM
— 1K × 16-bit Boot ROM
•
Off-Chip Memory Expansion (EMI)
— Access up to 2M words of program or 8M data memory (using chip selects)
— Chip Select Logic for glue-less interface to ROM and SRAM
1.1.3
56858 Peripheral Circuit Features
General Purpose 16-bit Quad Timer*
•
•
•
•
•
•
Two Serial Communication Interfaces (SCI)*
Serial Peripheral Interface (SPI) Port*
Two (2) Enhanced Synchronous Serial Interface (ESSI) modules*
Computer Operating Properly (COP)/Watchdog Timer
JTAG/Enhanced On-Chip Emulation (EOnCE) for unobtrusive, real-time debugging
56858 Technical Data, Rev. 6
4
Freescale Semiconductor
56858 Description
•
•
•
•
Six (6) independent channels of DMA
8-bit Parallel Host Interface*
Time-of-Day (TOD)
Up to 47 GPIO
* Each peripheral I/O can be used alternately as a GPIO if not needed
1.1.4
Energy Information
•
Fabricated in high-density CMOS with 3.3V, TTL-compatible digital inputs
•
Wait and Stop modes available
1.2 56858 Description
The 56858 is a member of the 56800E core-based family of controllers. This device combines the
processing power of a Digital Signal Processor (DSP) and the functionality of a microcontroller with a
flexible set of peripherals on a single chip to create an extremely cost-effective solution. The low cost,
flexibility, and compact program code make this device well-suited for many applications. The 56858
includes peripherals that are especially useful for teledatacom devices; Internet appliances; portable
devices; TAD; voice recognition; hands-free devices; and general purpose applications.
The 56800E core is based on a Harvard-style architecture consisting of three execution units operating in
parallel, allowing as many as six operations per instruction cycle. The microprocessor-style programming
model and optimized instruction set allow straightforward generation of efficient, compact DSP and
control code. The instruction set is also highly efficient for C Compilers, enabling rapid development of
optimized control applications.
The 56858 supports program execution from either internal or external memories. Two data operands can
be accessed from the on-chip Data RAM per instruction cycle. The 56858 also provides two external
dedicated interrupt lines, and up to 47 General Purpose Input/Output (GPIO) lines, depending on
peripheral configuration.
The 56858 controller includes 40K words of Program RAM, 24K words of Data RAM and 1K of Boot
RAM. It also supports program execution from external memory.
This controller also provides a full set of standard programmable peripherals that include an 8-bit Parallel
Host Interface, two Enhanced Synchronous Serial Interfaces (ESSI), one Serial Peripheral Interface (SPI),
two Serial Communications Interfaces (SCI), and one Quad Timer. The Host Interface, Quad Timer, SSI,
SPI, SCI I/O and four chip selects can be used as General Purpose Input/Outputs when its primary function
is not required.
1.3 State of the Art Development Environment
•
Processor ExpertTM (PE) provides a Rapid Application Design (RAD) tool that combines easy-to-use
component-based software application creation with an expert knowledge system.
•
The Code Warrior Integrated Development Environment is a sophisticated tool for code navigation,
compiling, and debugging. A complete set of evaluation modules (EVMs) and development system cards
will support concurrent engineering. Together, PE, Code Warrior and EVMs create a complete, scalable
tools solution for easy, fast, and efficient development.
56858 Technical Data, Rev. 6
Freescale Semiconductor
5
1.4 Product Documentation
The four documents listed in Table 1-1 are required for a complete description of and proper design with
the 56858. Documentation is available from local Freescale distributors, Freescale Semiconductor sales
offices, Freescale Literature Distribution Centers, or online at www.freescale.com.
Table 1-1 56858 Chip Documentation
Topic
Description
Order Number
56800ERM
56800E
Detailed description of the 56800E architecture, 16-bit
core processor and the instruction set
Reference Manual
DSP56858
User’s Manual
Detailed description of memory, peripherals, and
interfaces of the 56858
DSP5685xUM
DSP56858
56858
Technical Data Sheet
Electrical and timing specifications, pin descriptions,
and package descriptions (this document)
DSP56858
Errata
Details any chip issues that might be present
DSP56858E
1.5 Data Sheet Conventions
This data sheet uses the following conventions:
OVERBAR
This is used to indicate a signal that is active when pulled low. For example, the RESET pin is
active when low.
“asserted”
“deasserted”
Examples:
A high true (active high) signal is high or a low true (active low) signal is low.
A high true (active high) signal is low or a low true (active low) signal is high.
Voltage1
Signal/Symbol
Logic State
True
Signal State
Asserted
PIN
PIN
PIN
PIN
VIL/VOL
False
Deasserted
Asserted
VIH/VOH
VIH/VOH
VIL/VOL
True
False
Deasserted
1. Values for VIL, VOL, VIH, and VOH are defined by individual product specifications.
56858 Technical Data, Rev. 6
6
Freescale Semiconductor
Introduction
Part 2 Signal/Connection Descriptions
2.1 Introduction
The input and output signals of the 56858 are organized into functional groups, as shown in Table 2-1 and
as illustrated in Figure 2-1. In Table 3-1 each table row describes the package pin and the signal or signals
present.
Table 2-1 56858 Functional Group Pin Allocations
Functional Group
Number of Pins
(8, 12, 1)1
Power (VDD, VDDIO, or VDDA
)
(8, 14, 2)1
Ground (VSS, VSSIO,or VSSA
)
PLL and Clock
3
39
4
External Bus Signals
External Chip Select*
72
Interrupt and Program Control
Host Interface (HI)*
163
6
Enhanced Synchronous Serial Interface (ESSI0) Port*
Enhanced Synchronous Serial Interface (ESSI1) Port*
Serial Communications Interface (SCI0) Ports*
Serial Communications Interface (SCI1) Ports*
Serial Peripheral Interface (SPI) Port*
Quad Timer Module Port*
6
2
2
4
4
JTAG/On-Chip Emulation (OnCE)
6
*Alternately, GPIO pins
1. VDD = VDD CORE, VSS = VSS CORE, VDDIO= VDD IO, VSSIO = VSS IO, VDDA = VDD ANA, VSSA = VSS ANA
2. MODA, MODB and MODC can be used as GPIO after the bootstrap process has completed.
3. The following Host Interface signals are multiplexed: HRWB to HRD, HDS to HWR, HREQ to HTRQ and HACK to HRRQ.
56858 Technical Data, Rev. 6
Freescale Semiconductor
7
RXDO (GPIOE0)
TXDO (GPIOE1)
VDD
VSS
1
1
SCI 0
SCI 2
Logic
Power
8
8
56858
RXD1 (GPIOE2)
TXD1 (GPIOE3)
1
1
VDDIO
VSSIO
I/O
Power
12
14
STD0 (GPIOC0)
1
SRD0 (GPIOC1)
SCK0 (GPIOC2)
Analog
Power1
VDDA
VSSA
1
1
1
ESSI 0
ESSI 1
SPI
2
SC00 (GPIOC3)
SC01 (GPIOC4)
SC02 (GPIOC5)
1
1
1
A0 - A20
D0 - D15
RD
21
16
1
Address
Bus
STD1 (GPIOD0)
1
1
SRD1 (GPIOD1)
SCK1 (GPIOD2)
WR
1
1
1
1
1
SC10 (GPIOD3)
SC11 (GPIOD4)
SC12 (GPIOD5)
Chip
Select
CS0 - CS3 (GPIOA0 - A3)
4
HD0 - HD7 (GPIOB0 - B7)
HA0 - HA2 (GPIOB8 - B10)
HRWB (HRD) (GPIOB11)
HDS (HWR) (GPIOB12)
HCS (GPIOB13)
8
3
MISO (GPIOF0)
1
1
1
MOSI (GPIOF1)
SCK (GPIOF2)
1
1
Host
Interface
SS (GPIOF3)
1
1
1
HREQ (HTRQ) (GPIOB14)
HACK (HRRQ) (GPIOB15)
XTAL
1
1
1
1
EXTAL
CLKO
PLL /
Clock
Timer
Module
TIO0 - TIO3 (GPIOG0 - G3)
4
TCK
IRQA
IRQB
1
1
1
TDI
1
1
1
1
TDO
TMS
JTAG /
Enhanced
OnCE
MODA, MODB, MODC
(GPIOH0 - H2)
Interrupt /
Program
Control
3
RESET
RSTO
TRST
DE
1
1
1
2
Figure 2-1 56858 Signals Identified by Functional Group
1. Specifically for PLL, OSC, and POR.
2. Alternate pin functions are shown in parentheses. Pin direction/type is represented as the preferred functionality. GPIO may provide
bidirectional use of any pin.
56858 Technical Data, Rev. 6
8
Freescale Semiconductor
Introduction
Part 3 Signals and Package Information
All digital inputs have a weak internal pull-up circuit associated with them. These pull-up circuits are
enabled by default. Exceptions:
1. When a pin has GPIO functionality, the pull-up may be disabled under software control.
2. MODE A, MODE B and MODE C pins have no pull-up.
3. TCK has a weak pull-down circuit always active.
4. Bidirectional I/O pullups automatically disable when the output is enabled.
This table is presented consistently with the Signals Identified by Functional Group figure.
1. BOLD entries in the Type column represents the state of the pin just out of reset.
2. Output(Z) means an output in a High-Z condition.
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Description
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
E1
M6
F12
A9
14
36
VDD
Logic Power (VDD)—These pins provide power to the internal
structures of the chip, and should all be attached to VDD
.
52
72
M2
J12
E12
A12
G1
87
88
109
125
15
VSS
Logic Power–Ground (VSS)—These pins provide grounding for the
internal structures of the chip and should all be attached to VSS.
L6
16
D12
A7
53
54
F1
71
M7
K12
A8
89
126
127
56858 Technical Data, Rev. 6
Freescale Semiconductor
9
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Description
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VDDA
VSSA
B1
H1
5
VDDIO
I/O Power (VDDIO)—These pins provide power for all I/O and ESD
structures of the chip and should all be attached to VDDIO (3.3V).
6
M3
M8
M11
H12
C12
A11
A5
20
45
61
67
68
80
105
113
129
139
7
A3
C1
M10
D1
VSSIO
I/O Power–Ground (VSSIO)—These pins provide grounding for all I/O
and ESD structures of the chip and should all be attached to VSS.
J1
21
M5
M9
L12
G12
B12
A10
A4
46
47
62
69
70
82
106
115
128
130
140
141
A1
A2
M4
M12
A6
VDDA
VSSA
Analog Power (VDDA)—These pins supply an analog power source.
Analog Ground (VSSA)—This pin supplies an analog ground.
K1
M1
L1
24
25
26
VSSA
56858 Technical Data, Rev. 6
10
Freescale Semiconductor
Introduction
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Description
A0
A1
E5
E4
E3
E2
J2
10
11
12
13
29
30
31
32
48
49
50
51
63
64
65
66
75
76
77
78
79
Output(Z)
Address Bus (A0-A20)—These signals specify a word address for
external program or data memory access.
A2
A3
A4
A5
H3
G4
H4
G5
L5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
J6
K6
J8
K8
L9
K9
K10
K11
J9
J10
J11
56858 Technical Data, Rev. 6
Freescale Semiconductor
11
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Description
D0
D1
H7
G7
F9
81
94
Input/
Output(Z)
Data Bus (D0-D15)—These pins provide the bidirectional data for
external program or data memory accesses.
D2
95
D3
F10
F11
E10
D7
B7
E7
F8
96
D4
97
D5
98
D6
120
121
122
123
124
137
138
142
143
144
8
D7
D8
D9
D10
D11
D12
D13
D14
D15
RD
F7
D5
B4
C4
F6
B3
D3
Output
Output
Read Enable (RD) — is asserted during external memory read cycles.
This signal is pulled high during reset.
D4
H8
9
WR
Write Enable (WR) —is asserted during external memory write cycles.
This signal is pulled high during reset.
83
Output
CS0
External Chip Select (CS0)—This pin is used as a dedicated GPIO.
Input/Output
GPIOA0
Port A GPIO (0) —This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
H9
84
85
86
Output
CS1
External Chip Select (CS1)—This pin is used as a dedicated GPIO.
Input/Output
GPIOA1
Port A GPIO (1) —This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
H11
H10
Output
CS2
External Chip Select (CS2)—This pin is used as a dedicated GPIO.
Input/Output
GPIOA2
Port A GPIO (2) —This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Output
CS3
External Chip Select (CS3)—This pin is used as a dedicated GPIO.
Input/Output
GPIOA3
Port A GPIO (3)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
56858 Technical Data, Rev. 6
12
Freescale Semiconductor
Introduction
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Input
Description
HD0
J3
K2
L2
J4
L4
J5
33
34
35
40
41
42
Host Address (HD0)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB0
HD1
Input/Output Port B GPIO (0)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Input
Host Address (HD1)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB1
HD2
Input/Output Port B GPIO (1)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Input
Host Address (HD2)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB2
HD3
Input/Output Port B GPIO (2)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Input
Host Address (HD3)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB3
HD4
Input/Output Port B GPIO (3)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Input
Host Address (HD4)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB4
HD5
Input/Output Port B GPIO (4)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Input
Host Address (HD5)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB5
Input/Output Port B GPIO (5)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
56858 Technical Data, Rev. 6
Freescale Semiconductor
13
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Input
Description
HD6
K5
43
44
90
91
92
93
Host Address (HD6)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB6
HD7
Input/Output Port B GPIO (6)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
H5
Input
Host Address (HD7)—This input provides data selection for HI
registers.
This pin is disconnected internally during reset.
GPIOB7
HA0
Input/Output Port B GPIO (7)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
G10
G11
G9
Input
Host Address (HA0)—These inputs provide the address selection for
HI registers.
These pins are disconnected internally during reset.
GPIOB8
HA1
Input/Output Port B GPIO (8)—These pins are General Purpose I/O (GPIO) pins
when not configured for host port usage.
Input
Host Address (HA0)—These inputs provide the address selection for
HI registers.
These pins are disconnected internally during reset.
GPIOB9
HA2
Input/Output Port B GPIO (9)—These pins are General Purpose I/O (GPIO) pins
when not configured for host port usage.
Input
Host Address (HA0)—These inputs provide the address selection for
HI registers.
These pins are disconnected internally during reset.
GPIOB10
HRWB
Input/Output Port B GPIO (10)—These pins are General Purpose I/O (GPIO) pins
when not configured for host port usage.
G8
Input
Host Read/Write (HRWB)—When the HI08 is programmed to
interface to a single-data-strobe host bus and the HI function is
selected, this signal is the Read/Write input.
These pins are disconnected internally during reset.
HRD
Input
Host Read Data (HRD)—This signal is the Read Data input when the
HI08 is programmed to interface to a double-data-strobe host bus and
the HI function is selected.
GPIOB11
Input/Output
Port B GPIO (11) —This pin is a General Purpose I/O (GPIO) pin
when not configured for host port usage.
56858 Technical Data, Rev. 6
14
Freescale Semiconductor
Introduction
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Input
Description
C8
116
HDS
Host Data Strobe (HDS)—When the HI08 is programmed to interface
to a single-data-strobe host bus and the HI function is selected, this
input enables a data transfer on the HI when HCS is asserted.
These pins are disconnected internally during reset.
Input
HWR
Host Write Enable (HWR)—This signal is the Write Data input when
the HI08 is programmed to interface to a double-data-strobe host bus
and the HI function is selected.
Input/Output
GPIOB12
HCS
Port B GPIO (12)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
D8
B8
117
118
Input
Host Chip Select (HCS)—This input is the chip select input for the
Host Interface.
These pins are disconnected internally during reset.
Input/Output
GPIOB13
HREQ
Port B GPIO (13)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
Open Drain
Output
Host Request (HREQ)—When the HI08 is programmed for HRMS=0
functionality (typically used on a single-data-strobe bus), this open
drain output is used by the HI to request service from the host
processor. The HREQ may be connected to an interrupt request pin of
a host processor, a transfer request of a DMA controller, or a control
input of external circuitry.
These pins are disconnected internally during reset.
Open Drain
Output
HTRQ
Transmit Host Request (HTRQ)—This signal is the Transmit Host
Request output when the HI08 is programmed for HRMS=1
functionality and is typically used on a double-data-strobe bus.
GPIOB14
Input/Output Port B GPIO (14) —This pin is a General Purpose I/O (GPIO) pin
when not configured for host port usage.
56858 Technical Data, Rev. 6
Freescale Semiconductor
15
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Input
Description
C7
119
HACK
Host Acknowledge (HACK)—When the HI08 is programmed for
HRMS=0 functionality (typically used on a single-data-strobe bus), this
input has two functions: (1) provide a Host Acknowledge signal for
DMA transfers or (2) to control handshaking and provide a Host
Interrupt Acknowledge compatible with the MC68000 family
processors.
These pins are disconnected internally during reset.
Open Drain
Output
HRRQ
Receive Host Request (HRRQ)—This signal is the Receive Host
Request output when the HI08 is programmed for HRMS=1
functionality and is typically used on a double-data-strobe bus.
Input/Output
GPIOB15
TIO0
Port B GPIO (15)—This pin is a General Purpose I/O (GPIO) pin when
not configured for host port usage.
B9
C9
114
112
111
110
Input/Output Timer Input/Outputs (TIO0)—This pin can be independently
configured to be either a timer input source or an output flag.
GPIOG0
TIO1
Input/Output Port G GPIOG0—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as an input or output pin.
Input/Output Timer Input/Outputs (TIO1)—This pin can be independently
configured to be either a timer input source or an output flag.
GPIOG1
TIO2
Input/Output Port G GPIO (1)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as an input or output pin.
D9
Input/Output Timer Input/Outputs (TIO2)—This pin can be independently
configured to be either a timer input source or an output flag.
GPIOG2
TIO3
Input/Output Port G GPIO (2)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as an input or output pin.
B10
Input/Output Timer Input/Outputs (TIO3)—This pin can be independently
configured to be either a timer input source or an output flag.
GPIOG3
Input/Output Port G GPIO (3)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as an input or output pin.
G2
F5
22
23
Input
IRQA
IRQB
External Interrupt Request A and B—The IRQA and IRQB inputs
are asynchronous external interrupt requests that indicate that an
external device is requesting service. A Schmitt trigger input is used
for noise immunity. They can be programmed to be level-sensitive or
negative-edge-triggered. If level-sensitive triggering is selected, an
external pull-up resistor is required for Wired-OR operation.
MODE A
GPIOH0
F4
17
Input
Mode Select (MODE A)—During the bootstrap process MODE A
selects one of the eight bootstrap modes.
Input/Output Port H GPIO (0)—This pin is a General Purpose I/O (GPIO) pin after
the bootstrap process has completed.
56858 Technical Data, Rev. 6
16
Freescale Semiconductor
Introduction
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Input
Description
MODE B
F3
F2
K4
18
19
39
Mode Select (MODE B)—During the bootstrap process MODE A
selects one of the eight bootstrap modes.
GPIOH1
MODE C
Input/Output Port H GPIO (1)—This pin is a General Purpose I/O (GPIO) pin after
the bootstrap process has completed.
Input
Mode Select (MODE C)—During the bootstrap process MODE A
selects one of the eight bootstrap modes.
GPIOH2
RESET
Input/Output Port H GPIO (2)—This pin is a General Purpose I/O (GPIO) pin after
the bootstrap process has completed.
Input
Reset (RESET)—This input is a direct hardware reset on the
processor. When RESET is asserted low, the device is initialized and
placed in the Reset state. A Schmitt trigger input is used for noise
immunity. When the RESET pin is deasserted, the initial chip operating
mode is latched from the MODE A, MODE B, and MODE C pins.
To ensure complete hardware reset, RESET and TRST should be
asserted together. The only exception occurs in a debugging
environment when a hardware reset is required and it is necessary not
to reset the JTAG/Enhanced OnCE module. In this case, assert
RESET, but do not assert TRST.
K3
38
73
Output
RSTO
RXD0
Reset Output (RSTO)—This output is asserted on any reset condition
(external reset, low voltage, software, or COP).
L10
Input
Serial Receive Data 0 (RXD0)—This input receives byte-oriented
serial data and transfers it to the SCI 0 receive shift register.
GPIOE0
TXD0
Input/Output Port E GPIO (0)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
L11
B11
C10
74
Output(Z)
Serial Transmit Data 0 (TXD0)—This signal transmits data from the
SCI 0 transmit data register.
GPIOE1
RXD1
Input/Output Port E GPIO (1)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
107
108
Input
Serial Receive Data 1 (RXD1)—This input receives byte-oriented
serial data and transfers it to the SCI 1 receive shift register.
GPIOE2
TXD1
Input/Output Port E GPIO (2)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
Output(Z)
Serial Transmit Data 1 (TXD1)—This signal transmits data from the
SCI 1 transmit data register.
GPIOE3
Input/Output
Port E GPIO (3)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
56858 Technical Data, Rev. 6
Freescale Semiconductor
17
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Description
STD0
B6
C6
C5
131
132
133
Output
ESSI Transmit Data (STD0)—This output pin transmits serial data
from the ESSI Transmitter Shift Register.
GPIOC0
SRD0
Input/Output Port C GPIO (0)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input
ESSI Receive Data (SRD0)—This input pin receives serial data and
transfers the data to the ESSI Receive Shift Register.
GPIOC1
SCK0
Input/Output Port C GPIO (1)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output ESSI Serial Clock (SCK0)—This bidirectional pin provides the serial
bit rate clock for the transmit section of the ESSI. The clock signal can
be continuous or gated and can be used by both the transmitter and
receiver in synchronous mode.
GPIOC2
SC00
Input/Output Port C GPIO (2)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
D6
B5
E6
134
135
136
Input/Output ESSI Serial Control Pin 0 (SC00)—The function of this pin is
determined by the selection of either synchronous or asynchronous
mode. For asynchronous mode, this pin will be used for the receive
clock I/O. For synchronous mode, this pin is used either for
transmitter1 output or for serial I/O flag 0.
GPIOC3
SC01
Input/Output Port C GPIO (3)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output ESSI Serial Control Pin 1 (SC01)—The function of this pin is
determined by the selection of either synchronous or asynchronous
mode. For asynchronous mode, this pin is the receiver frame sync I/O.
For synchronous mode, this pin is used either for transmitter2 output
or for serial I/O flag 1.
GPIOC4
SC02
Input/Output Port C GPIO (4)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output ESSI Serial Control Pin 2 (SC02)—This pin is used for frame sync
I/O. SC02 is the frame sync for both the transmitter and receiver in
synchronous mode and for the transmitter only in asynchronous mode.
When configured as an output, this pin is the internally generated
frame sync signal. When configured as an input, this pin receives an
external frame sync signal for the transmitter (and the receiver in
synchronous operation).
GPIOC5
Input or Output Port C GPIO (5)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
56858 Technical Data, Rev. 6
18
Freescale Semiconductor
Introduction
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Description
STD1
E8
E11
E9
99
Output
ESSI Transmit Data (STD1)—This output pin transmits serial data
from the ESSI Transmitter Shift Register.
GPIOD0
SRD1
Input/Output Port D GPIO (0)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
100
101
Input
ESSI Receive Data (SRD1)—This input pin receives serial data and
transfers the data to the ESSI Receive Shift Register.
GPIOD1
SCK1
Input/Output Port D GPIO (1)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output ESSI Serial Clock (SCK1)—This bidirectional pin provides the serial
bit rate clock for the transmit section of the ESSI. The clock signal can
be continuous or gated and can be used by both the transmitter and
receiver in synchronous mode.
GPIOD2
SC10
Input/Output Port D GPIO (2)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
D10
D11
C11
102
103
104
Input/Output ESSI Serial Control Pin 0 (SC10)—The function of this pin is
determined by the selection of either synchronous or asynchronous
mode. For asynchronous mode, this pin will be used for the receive
clock I/O. For synchronous mode, this pin is used either for
transmitter1 output or for serial I/O flag 0.
GPIOD3
SC11
Input/Output Port D GPIO (3)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output ESSI Serial Control Pin 1 (SC11)—The function of this pin is
determined by the selection of either synchronous or asynchronous
mode. For asynchronous mode, this pin is the receiver frame sync I/O.
For synchronous mode, this pin is used either for transmitter2 output
or for serial I/O flag 1.
GPIOD4
SC12
Input/Output Port D GPIO (4)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
Input/Output ESSI Serial Control Pin 2 (SC12)—This pin is used for frame sync
I/O. SC02 is the frame sync for both the transmitter and receiver in
synchronous mode and for the transmitter only in asynchronous mode.
When configured as an output, this pin is the internally generated
frame sync signal. When configured as an input, this pin receives an
external frame sync signal for the transmitter (and the receiver in
synchronous operation).
GPIOC5
Input/Output Port D GPIO (5)—This pin is a General Purpose I/O (GPIO) pin when
the ESSI is not in use.
56858 Technical Data, Rev. 6
Freescale Semiconductor
19
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Description
MISO
B2
C3
C2
1
2
3
Input/Output SPI Master In/Slave Out (MISO)—This serial data pin is an input to a
master device and an output from a slave device. The MISO line of a
slave device is placed in the high-impedance state if the slave device
is not selected. The driver on this pin can be configured as an
open-drain driver by the SPI’s Wired-OR mode (WOM) bit when this
pin is configured for SPI operation.
GPIOF0
MOSI
Input/Output Port F GPIO (0)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
Input/
Output (Z)
SPI Master Out/Slave In (MOSI)—This serial data pin is an output
from a master device and an input to a slave device. The master
device places data on the MOSI line a half-cycle before the clock edge
that the slave device uses to latch the data. The driver on this pin can
be configured as an open-drain driver by the SPI’s WOM bit when this
pin is configured for SPI operation.
GPIOF1
SCK
Input/Output Port F GPIO (1)—This pin is a General Purpose I/O (GPIO) pin that
can be individually programmed as input or output pin.
Input/Output SPI Serial Clock (SCK)—This bidirectional pin provides a serial bit
rate clock for the SPI. This gated clock signal is an input to a slave
device and is generated as an output by a master device. Slave
devices ignore the SCK signal unless the SS pin is active low. In both
master and slave SPI devices, data is shifted on one edge of the SCK
signal and is sampled on the opposite edge where data is stable. The
driver on this pin can be configured as an open-drain driver by the
SPI’s WOM bit when this pin is configured for SPI operation. When
using Wired-OR mode, the user must provide an external pull-up
device.
GPIOF2
SS
Input/Output Port F GPIO (2)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
D2
H2
4
Input
SPI Slave Select (SS)—This input pin selects a slave device before a
master device can exchange data with the slave device. SS must be
low before data transactions and must stay low for the duration of the
transaction. The SS line of the master must be held high.
Input/Output
GPIOF3
XTAL
Port F GPIO (3)—This pin is a General Purpose I/O (GPIO) pin that
can individually be programmed as input or output pin.
27
Input/Output Crystal Oscillator Output (XTAL)—This output connects the internal
crystal oscillator output to an external crystal. If an external clock
source other than a crystal oscillator is used, XTAL must be used as
the input.
EXTAL
CLKO
G3
L3
28
37
Input
External Crystal Oscillator Input (EXTAL)—This input should be
connected to an external crystal. If an external clock source other than
a crystal oscillator is used, EXTAL must be tied off. See Section 4.5.2
Output
Clock Output (CLKO)—This pin outputs a buffered clock signal.
When enabled, this signal is the system clock divided by four.
56858 Technical Data, Rev. 6
20
Freescale Semiconductor
Introduction
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Description
TCK
L8
K7
G6
60
58
57
Input
Test Clock Input (TCK)—This input pin provides a gated clock to
synchronize the test logic and to shift serial data to the JTAG/OnCE
port. The pin is connected internally to a pull-down resistor.
TDI
Input
Test Data Input (TDI)—This input pin provides a serial input data
stream to the JTAG/OnCE port. It is sampled on the rising edge of
TCK and has an on-chip pull-up resistor.
TDO
Output(Z)
Test Data Output (TDO)—This tri-statable output pin provides a serial
output data stream from the JTAG/Enhanced OnCE port. It is driven in
the Shift-IR and Shift-DR controller states, and changes on the falling
edge of TCK.
TMS
J7
L7
59
56
Input
Input
Test Mode Select Input (TMS)—This input pin is used to sequence
the JTAG TAP controller’s state machine. It is sampled on the rising
edge of TCK and has an on-chip pull-up resistor.
Note: Always tie the TMS pin to VDD through a 2.2K resistor.
TRST
Test Reset (TRST)—As an input, a low signal on this pin provides a
reset signal to the JTAG TAP controller. To ensure complete hardware
reset, TRST should be asserted whenever RESET is asserted. The
only exception occurs in a debugging environment, since the
Enhanced OnCE/JTAG module is under the control of the debugger. In
this case it is not necessary to assert TRST when asserting RESET.
Outside of a debugging environment RESET should be permanently
asserted by grounding the signal, thus disabling the Enhanced
OnCE/JTAG module on the device.
Note: For normal operation, connect TRST directly to VSS. If the design is
to be used in a debugging environment, TRST may be tied to VSS through a
1K resistor.
56858 Technical Data, Rev. 6
Freescale Semiconductor
21
Table 3-1 56858 Signal and Package Information for the 144-pin LQFP and MAPBGA
Signal
Name
BGA
Pin No. Pin No.
LQFP
Type
Description
H6 55
Input/Output
DE
Debug Event (DE)—This is an open-drain, bidirectional, active low
signal. As an input, it is a means of entering debug mode of operation
from an external command controller. As an output, it is a means of
acknowledging that the chip has entered debug mode.
This pin is connected internally to a weak pull-up resistor.
Part 4 Specifications
4.1 General Characteristics
The 56858 is fabricated in high-density CMOS with 5-volt tolerant TTL-compatible digital inputs. The
term “5-volt tolerant” refers to the capability of an I/O pin, built on a 3.3V compatible process technology,
to withstand a voltage up to 5.5V without damaging the device. Many systems have a mixture of devices
designed for 3.3V and 5V power supplies. In such systems, a bus may carry both 3.3V and 5V-compatible
I/O voltage levels (a standard 3.3V I/O is designed to receive a maximum voltage of 3.3V ± 10% during
normal operation without causing damage). This 5V tolerant capability therefore offers the power savings
of 3.3V I/O levels while being able to receive 5V levels without being damaged.
Absolute maximum ratings given in Table 4-1 are stress ratings only, and functional operation at the
maximum is not guaranteed. Stress beyond these ratings may affect device reliability or cause permanent
damage to the device.
The 56858 DC/AC electrical specifications are preliminary and are from design simulations. These
specifications may not be fully tested or guaranteed at this early stage of the product life cycle. Finalized
specifications will be published after complete characterization and device qualifications have been
completed.
56858 Technical Data, Rev. 6
22
Freescale Semiconductor
General Characteristics
CAUTION
This device contains protective circuitry to guard
against damage due to high static voltage or
electrical fields. However, normal precautions are
advised to avoid application of any voltages higher
than maximum rated voltages to this high-impedance
circuit. Reliability of operation is enhanced if unused
inputs are tied to an appropriate voltage level.
Table 4-1 Absolute Maximum Ratings
Characteristic
Supply voltage, core
Symbol
Min
Max
Unit
1
VSS – 0.3
VSS + 2.0
V
VDD
2
V
VDDIO
VSSIO – 0.3
VSSA – 0.3
V
SSIO + 4.0
Supply voltage, IO
Supply voltage, analog
2
VDDA + 4.0
VDDIO
Digital input voltages
Analog input voltages (XTAL, EXTAL)
VIN
VSSIO – 0.3
VSSA – 0.3
V
SSIO + 5.5
V
VINA
VDDA + 0.3
Current drain per pin excluding VDD, GND
Junction temperature
I
—
8
mA
°C
TJ
-40
-55
120
150
Storage temperature range
TSTG
°C
1. VDD must not exceed VDDIO
2. VDDIO and VDDA must not differ by more that 0.5V
Table 4-2 Recommended Operating Conditions
Characteristic
Supply voltage for Logic Power
Symbol
VDD
VDDIO
VDDA
TA
Min
1.62
3.0
3.0
-40
—
Max
1.98
3.6
Unit
V
Supply voltage for I/O Power
Supply voltage for Analog Power
Ambient operating temperature
V
3.6
V
85
°C
PLL clock frequency1
fpll
240
120
60
MHz
MHz
MHz
Operating Frequency2
fop
—
Frequency of peripheral bus
fipb
—
56858 Technical Data, Rev. 6
Freescale Semiconductor
23
Table 4-2 Recommended Operating Conditions (Continued)
Characteristic
Frequency of external clock
Symbol
fclk
Min
—
2
Max
240
4
Unit
MHz
MHz
MHz
MHz
Frequency of oscillator
fosc
Frequency of clock via XTAL
Frequency of clock via EXTAL
fxtal
—
2
240
4
fextal
1. Assumes clock source is direct clock to EXTAL or crystal oscillator running 2-4MHz. PLL must be enabled, locked, and
selected. The actual frequency depends on the source clock frequency and programming of the CGM module.
2. Master clock is derived from on of the following four sources:
fclk = fxtal when the source clock is the direct clock to EXTAL
fclk = fpll when PLL is selected
fclk = fosc when the source clock is the crystal oscillator and PLL is not selected
fclk = fextal when the source clock is the direct clock to EXTAL and PLL is not selected
1
Table 4-3 Thermal Characteristics
Value
Characteristic
Symbol
Unit
144-pin LQFP
144 MAPBGA
Thermal resistance junction-to-ambient
(estimated)
θJA
42.9
36.1
°C/W
I/O pin power dissipation
Power dissipation
PI/O
PD
User Determined
W
W
W
PD = (IDD x VDD) + PI/O
2
Maximum allowed PD
PDMAX
(TJ - TA) / RθJA
1. See Section 6.1 for more detail.
2. TJ = Junction Temperature
TA = Ambient Temperature
4.2 DC Electrical Characteristics
Table 4-4 DC Electrical Characteristics
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40
°
to +120
°
C, C ≤
50pF, f = 120MHz
op
SS
SSIO
SSA
DD
DDIO
DDA
A
L
Characteristic
Input high voltage (XTAL/EXTAL)
Input low voltage (XTAL/EXTAL)
Input high voltage
Symbol
VIHC
VILC
Min
Typ
VDDA
—
Max
Unit
V
VDDA – 0.8
-0.3
VDDA + 0.3
0.5
5.5
0.8
V
VIH
2.0
—
V
Input low voltage
VIL
-0.3
—
V
56858 Technical Data, Rev. 6
24
Freescale Semiconductor
DC Electrical Characteristics
Table 4-4 DC Electrical Characteristics (Continued)
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40° to +120°C, C ≤ 50pF, f = 120MHz
SS
SSIO
SSA
DD
DDIO
DDA A L op
Characteristic
Input current low (pullups disabled)
Input current high (pullups disabled)
Output tri-state current low
Output tri-state current high
Output High Voltage
Symbol
IIL
Min
-1
Typ
—
—
—
—
—
—
—
—
8
Max
1
Unit
μA
μA
μA
μA
V
IIH
-1
1
IOZL
IOZH
VOH
VOL
IOH
-10
-10
10
10
—
VDDIO – 0.7
Output Low Voltage
—
8
0.4
16
16
—
V
Output High Current
mA
mA
pF
pF
Output Low Current
IOL
8
Input capacitance
CIN
—
—
Output capacitance
COUT
12
—
4
V
DD supply current (Core logic, memories, peripherals)
IDD
Run 1
—
—
—
70
0.05
5
110
10
14
mA
mA
mA
Deep Stop2
Light Stop3
VDDIO supply current (I/O circuity)
IDDIO
Run5
Deep Stop2
—
40
0
50
1.5
mA
mA
VDDA supply current (analog circuity)
Deep Stop2
IDDA
—
—
—
—
60
2.5
50
120
2.85
—
μA
V
Low Voltage Interrupt6
VEI
Low Voltage Interrupt Recovery Hysteresis
VEIH
POR
mV
V
Power on Reset7
1.5
2.0
Note:
Run (operating) IDD measured using external square wave clock source (fosc = 4MHz) into XTAL. All inputs 0.2V from rail;
no DC loads; outputs unloaded. All ports configured as inputs; measured with all modules enabled. PLL set to 240MHz out.
1. Running Core, performing 50% NOP and 50% FIR. Clock at 120 MHz.
2. Deep Stop Mode - Operation frequency = 4 MHz, PLL set to 4 MHz, crystal oscillator and time of day module operating.
3. Light Stop Mode - Operation frequency = 120 MHz, PLL set to 240 MHz, crystal oscillator and time of day module operating.
4. IDD includes current for core logic, internal memories, and all internal peripheral logic circuitry.
5. Running core and performing external memory access. Clock at 120 MHz.
6. When VDD drops below VEI max value, an interrupt is generated.
7. Power-on reset occurs whenever the digital supply drops below 1.8V. While power is ramping up, this signal remains active
for as long as the internal 2.5V is below 1.8V no matter how long the ramp up rate is. The internally regulated voltage is
typically 100 mV less than VDD during ramp up until 2.5V is reached, at which time it self-regulates.
56858 Technical Data, Rev. 6
Freescale Semiconductor
25
150
MAC Mode1
EMI Mode5
120
90
60
30
0
20
40
120
100
60
80
Figure 4-1 Maximum Run I
vs. Frequency (see Notes 1. and 5. in Table 4-4)
DDTOTAL
4.3 Supply Voltage Sequencing and Separation Cautions
Figure 4-2 shows two situations to avoid in sequencing the V and V
V
supplies.
DD
DDIO, DDA
3.3V
VDDIO, VDDA
2
Supplies Stable
1.8V
VDD
1
0
Time
Note: 1. VDD rising before VDDIO, VDDA
2. VDDIO, VDDA rising much faster than VDD
Figure 4-2 Supply Voltage Sequencing and Separation Cautions
56858 Technical Data, Rev. 6
26
Freescale Semiconductor
AC Electrical Characteristics
V
should not be allowed to rise early (1). This is usually avoided by running the regulator for the V
DD
DD
supply (1.8V) from the voltage generated by the 3.3V V
supply, see Figure 4-3. This keeps V from
DDIO
DD
rising faster than V
.
DDIO
V
should not rise so late that a large voltage difference is allowed between the two supplies (2).
DD
Typically this situation is avoided by using external discrete diodes in series between supplies, as shown
in Figure 4-3. The series diodes forward bias when the difference between V and V reaches
DDIO
DD
approximately 2.1, causing V to rise as V
ramps up. When the V regulator begins proper
DD
DDIO
DD
operation, the difference between supplies will typically be 0.8V and conduction through the diode chain
reduces to essentially leakage current. During supply sequencing, the following general relationship
should be adhered to:
V
> V > (V
- 2.1V)
DDIO
DD
DDIO
In practice, V
is typically connected directly to V
with some filtering.
DDA
DDIO
VDDIO, VDDA
3.3V
Regulator
Supply
VDD
1.8V
Regulator
Figure 4-3 Example Circuit to Control Supply Sequencing
4.4 AC Electrical Characteristics
Timing waveforms in Section 4.3 are tested with a VIL maximum of 0.8V and a VIH minimum of 2.0V for
all pins except XTAL, which is tested using the input levels in Section 4.2. In Figure 4-4 the levels of VIH
and VIL for an input signal are shown.
Low
VIL
High
VIH
90%
50%
10%
Input Signal
Midpoint1
Fall Time
Note: The midpoint is VIL + (VIH – VIL)/2.
Rise Time
Figure 4-4 Input Signal Measurement References
56858 Technical Data, Rev. 6
Freescale Semiconductor
27
Figure 4-5 shows the definitions of the following signal states:
•
•
•
Active state, when a bus or signal is driven, and enters a low impedance state
Tri-stated, when a bus or signal is placed in a high impedance state
Data Valid state, when a signal level has reached VOL or VOH
•
Data Invalid state, when a signal level is in transition between VOL and VOH
Data2 Valid
Data2
Data1 Valid
Data1
Data3 Valid
Data3
Data
Tri-stated
Data Invalid State
Data Active
Data Active
Figure 4-5 Signal States
4.5 External Clock Operation
The 56858 system clock can be derived from a crystal or an external system clock signal. To generate a
reference frequency using the internal oscillator, a reference crystal must be connected between the
EXTAL and XTAL pins.
4.5.1
Crystal Oscillator
The internal oscillator is designed to interface with a parallel-resonant crystal resonator in the frequency
range specified for the external crystal in Table 4-6. In Figure 4-6 a typical crystal oscillator circuit is
shown. Follow the crystal supplier’s recommendations when selecting a crystal, because crystal
parameters determine the component values required to provide maximum stability and reliable start-up.
The crystal and associated components should be mounted as close as possible to the EXTAL and XTAL
pins to minimize output distortion and start-up stabilization time.
Crystal Frequency = 2–4MHz (optimized for 4MHz)
Sample External Crystal Parameters:
EXTAL XTAL
Rz = 10MΩ
TOD_SEL bit in CGM must be set to 0
Rz
fc = 4MHz
f
C
Figure 4-6 Crystal Oscillator
56858 Technical Data, Rev. 6
28
Freescale Semiconductor
External Clock Operation
4.5.2
High Speed External Clock Source (> 4MHz)
The recommended method of connecting an external clock is given in Figure 4-7. The external clock
source is connected to XTAL and the EXTAL pin is held at ground, V
bit in CGM must be set to 0.
, or V
/2. The TOD_SEL
DDA
DDA
56858
XTAL
EXTAL
GND,VDDA
or VDDA/2
,
External
Clock
(up to 240MHz)
Figure 4-7 Connecting a High Speed External Clock Signal using XTAL
4.5.3
Low Speed External Clock Source (2-4MHz)
The recommended method of connecting an external clock is given in Figure 4-8. The external clock
source is connected to XTAL and the EXTAL pin is held at V
set to 0.
/2. The TOD_SEL bit in CGM must be
DDA
56858
XTAL
EXTAL
External
Clock
VDDA/2
(2-4MHz)
Figure 4-8 Connecting a Low Speed External Clock Signal using XTAL
4
Table 4-5 External Clock Operation Timing Requirements
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40° to +120°C, C ≤ 50pF, f = 120MHz
SS
SSIO
SSA
DD
DDIO
DDA A L op
Characteristic
Symbol
fosc
Min
0
Typ
Max
240
—
Unit
MHz
ns
Frequency of operation (external clock driver)1
Clock Pulse Width4
—
—
—
—
tPW
6.25
—
External clock input rise time2, 4
External clock input fall time3, 4
trise
TBD
TBD
ns
tfall
—
ns
1. See Figure 4-7 for details on using the recommended connection of an external clock driver.
2. External clock input rise time is measured from 10% to 90%.
3. External clock input fall time is measured from 90% to 10%.
4. Parameters listed are guaranteed by design.
56858 Technical Data, Rev. 6
Freescale Semiconductor
29
VIH
External
Clock
90%
50%
10%
90%
50%
10%
tPW
tPW
VIL
trise
tfall
Note: The midpoint is VIL + (VIH – VIL)/2.
Figure 4-9 External Clock Timing
Table 4-6 PLL Timing
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40° to +120°C, C ≤ 50pF, f = 120MHz
SS
SSIO
SSA
DD
DDIO
DDA A L op
Characteristic
Symbol
fosc
Min
2
Typ
Max
4
Unit
MHz
MHz
ms
External reference crystal frequency for the PLL1
PLL output frequency
4
—
1
fclk
40
—
240
10
PLL stabilization time 2
tplls
1. An externally supplied reference clock should be as free as possible from any phase jitter for the PLL to work correctly.
The PLL is optimized for 4MHz input crystal.
2. This is the minimum time required after the PLL setup is changed to ensure reliable operation.
4.6 External Memory Interface Timing
The External Memory Interface is designed to access static memory and peripheral devices. Figure 4-10 shows
sample timing and parameters that are detailed in Table 4-7.
The timing of each parameter consists of both a fixed delay portion and a clock related portion; as well as user
controlled wait states. The equation:
t = D + P * (M + W)
should be used to determine the actual time of each parameter. The terms in the above equation are defined as:
t
parameter delay time
D fixed portion of the delay, due to on-chip path delays.
P
the period of the system clock, which determines the execution rate of the part (i.e. when the device is
operating at 120 MHz, P = 8.33 ns).
56858 Technical Data, Rev. 6
30
Freescale Semiconductor
External Memory Interface Timing
M Fixed portion of a clock period inherent in the design. This number is adjusted to account for possible
clock duty cycle derating.
W the sum of the applicable wait state controls. See the “Wait State Controls” column of Table 4-7 for
the applicable controls for each parameter. See the EMI chapter of the 83x Peripheral Manual for
details of what each wait state field controls.
Some of the parameters contain two sets of numbers. These parameters have two different paths and clock edges
that must be considered. Check both sets of numbers and use the smaller result. The appropriate entry may change
if the operating frequency of the part changes.
The timing of write cycles is different when WWS = 0 than when WWS > 0. Therefore, some parameters contain
two sets of numbers to account for this difference. The “Wait States Configuration” column of Table 4-7 should be
used to make the appropriate selection.
A0-Axx,CS
tRD
tARDD
tRDA
tRDRD
tARDA
RD
tWAC
tWRRD
tAWR
tWRWR
tWR
tRDWR
WR
tDWR
tDOH
tRDD
tDOS
Data Out
tAD
tDRD
Data In
D0-D15
Note: During read-modify-write instructions and internal instructions, the address lines do not change state.
Figure 4-10 External Memory Interface Timing
56858 Technical Data, Rev. 6
Freescale Semiconductor
31
Table 4-7 External Memory Interface Timing
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98 V, V
= V
= 3.0–3.6V, T = –40× to +120×C, C £ 50pF, P = 8.333ns
SS
SSIO
SSA
DD
DDIO
DDA
A
L
Wait States
Configuration
Wait States
Controls
Characteristic
Symbol
tAWR
D
M
Unit
ns
WWS=0
WWS>0
WWS=0
WWS>0
WWS=0
WWS=0
WWS>0
WWS>0
-0.79
-1.98
-0.86
-0.01
-1.52
- 5.69
-2.10
-4.66
0.50
0.69
0.19
0.00
0.00
0.25
0.19
0.50
Address Valid to WR Asserted
WWSS
WWS
WR Width Asserted to WR
Deasserted
tWR
ns
Data Out Valid to WR Asserted
tDWR
WWSS
ns
Valid Data Out Hold Time after WR
Deasserted
tDOH
-1.47
0.25
WWSH
WWS,WWSS
WWSH
ns
ns
-2.36
-4.67
0.19
0.50
Valid Data Out Set Up Time to WR
Deasserted
tDOS
tWAC
Valid Address after WR
Deasserted
-1.60
0.25
tRDA
- 0.44
-2.07
0.00
1.00
RWSH
ns
ns
RD Deasserted to Address Invalid
Address Valid to RD Deasserted
tARDD
RWSS,RWS
Valid Input Data Hold after RD
Deasserted
N/A1
1.00
tDRD
tRD
0.00
—
ns
ns
ns
ns
ns
-1.34
RWS
RD Assertion Width
-10.27
-13.5
1.00
1.19
Address Valid to Input Data Valid
tAD
RWSS,RWS
RWSS
tARDA
tRDD
tWRRD
tRDRD
tWRWR
- 0.94
0.00
Address Valid to RD Asserted
-9.53
1.00
1.19
RD Asserted to Input Data Valid
RWSS,RWS
WWSH,RWSS
RWSS,RWSH
-12.64
-0.75
0.25
0.00
ns
ns
WR Deasserted to RD Asserted
RD Deasserted to RD Asserted
WR Deasserted to WR Asserted
-0.162
-0.44
-0.11
0.14
WWS=0
WWS>0
0.75
1.00
0.50
0.69
WWSS, WWSH
ns
ns
MDAR, BMDAR,
RWSH, WWSS
RD Deasserted to WR Asserted
tRDWR
-0.57
1. N/A since device captures data before it deasserts RD
2. If RWSS = RWSH = 0, RD does not deassert during back-to-back reads and D=0.00 should be used.
56858 Technical Data, Rev. 6
32
Freescale Semiconductor
Reset, Stop, Wait, Mode Select, and Interrupt Timing
4.7 Reset, Stop, Wait, Mode Select, and Interrupt Timing
1, 2
Table 4-8 Reset, Stop, Wait, Mode Select, and Interrupt Timing
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40
°
to +120
°
C, C ≤
50pF, f = 120MHz
op
SS
SSIO
SSA
DD
DDIO
DDA
A
L
Characteristic
Symbol
Min
Max
Unit
See Figure
Figure 4-11
RESET Assertion to Address, Data and Control
Signals High Impedance
tRAZ
—
11
ns
Minimum RESET Assertion Duration3
tRA
tRDA
30
—
—
120T
—
ns
ns
ns
ns
Figure 4-11
Figure 4-11
Figure 4-12
Figure 4-13
RESET Deassertion to First External Address Output
Edge-sensitive Interrupt Request Width
tIRW
1T + 3
18T
14T
18T
14T
22T
18T
IRQA, IRQB Assertion to External Data Memory
Access Out Valid, caused by first instruction execution
in the interrupt service routine
tIDM
—
tIDM -FAST
tIG
tIG -FAST
tIRI
tIRI -FAST
tIW
—
IRQA, IRQB Assertion to General Purpose Output
Valid, caused by first instruction execution in the
interrupt service routine
—
ns
ns
Figure 4-13
Figure 4-14
—
IRQA Low to First Valid Interrupt Vector Address Out
recovery from Wait State4
—
—
Delay from IRQA Assertion (exiting Stop) to External
Data Memory5
Figure 4-15
Figure 4-15
1.5T
—
ns
Delay from IRQA Assertion (exiting Wait) to External
Data Memory
tIF
Fast6
Normal7
18T
22ET
ns
ns
—
—
RSTO pulse width8
normal operation
internal reset mode
tRSTO
Figure 4-16
128ET
8ET
—
—
—
—
1. In the formulas, T = clock cycle. For fop = 120MHz operation and fipb = 60MHz, T = 8.33ns.
2. Parameters listed are guaranteed by design.
3. At reset, the PLL is disabled and bypassed. The part is then put into Run mode and tclk assumes the period of the source clock,
xtal, textal or tosc
t
.
4. The minimum is specified for the duration of an edge-sensitive IRQA interrupt required to recover from the Stop state. This is not
the minimum required so that the IRQA interrupt is accepted.
5. The interrupt instruction fetch is visible on the pins only in Mode 3.
6. Fast stop mode:
Fast stop recovery applies when external clocking is in use (direct clocking to XTAL) or when fast stop mode recovery is
requested (OMR bit 6 is set to 1). In both cases the PLL and the master clock are unaffected by stop mode entry. Recovery takes
one less cycle and tclk will continue same value it had before stop mode was entered.
56858 Technical Data, Rev. 6
Freescale Semiconductor
33
7. Normal stop mode:
As a power saving feature, normal stop mode disables and bypasses the PLL. Stop mode will then shut down the master clock,
recovery will take an extra cycle (to restart the clock), and tclk will resume at the input clock source rate.
8. ET = External Clock period, For an external crystal frequency of 8MHz, ET=125 ns.
RESET
tRA
tRAZ
tRDA
A0–Axx,
D0–D15
First Fetch
First Fetch
CS,
RD, WR
Figure 4-11 Asynchronous Reset Timing
IRQA
IRQB
tIRW
Figure 4-12 External Interrupt Timing (Negative-Edge-Sensitive)
A0–Axx,
CS,
RD, WR
First Interrupt Instruction Execution
tIDM
IRQA,
IRQB
a) First Interrupt Instruction Execution
General
Purpose
I/O Pin
tIG
IRQA,
IRQB
b) General Purpose I/O
Figure 4-13 External Level-Sensitive Interrupt Timing
56858 Technical Data, Rev. 6
34
Freescale Semiconductor
Reset, Stop, Wait, Mode Select, and Interrupt Timing
IRQA,
IRQB
tIRI
A0–Axx,
CS,
RD, WR
First Interrupt Vector
Instruction Fetch
Figure 4-14 Interrupt from Wait State Timing
tIW
IRQA
tIF
A0–Axx,
CS,
RD, WR
First Instruction Fetch
Not IRQA Interrupt Vector
Figure 4-15 Recovery from Stop State Using Asynchronous Interrupt Timing
RESET
tRSTO
Figure 4-16 Reset Output Timing
56858 Technical Data, Rev. 6
Freescale Semiconductor
35
4.8 Host Interface Port
1
Table 4-9 Host Interface Port Timing
Operating Conditions: VSS = VSSIO = VSSA = 0 V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0–3.6V, TA = –40° to +120°C, CL ≤ 50pF, fop = 120MHz
Characteristic
Symbol
Min
Max
Unit See Figure
TACKDV
TACKDZ
Access time
Disable time
—
3
13
—
ns
ns
4-17
4-17
4-17
4-20
TACKREQH
TREQACKL
TRADV
Time to disassert
Lead time
3.5
0
9
ns
4-17
4-20
—
13
—
—
ns
ns
4-18
4-19
Access time
Disable time
Disable time
—
5
ns
ns
4-18
4-19
TRADX
4-18
4-19
TRADZ
3
TDACKS
TACKDH
Setup time
Hold time
3
1
—
—
ns
ns
4-20
4-20
4-21
4-22
TADSS
TDSAH
TWDS
Setup time
Hold time
3
1
5
—
—
—
ns
ns
ns
4-21
4-22
4-21
4-22
Pulse width
Time to re-assert
TACKREQL
1. After second write in 16-bit mode
2. After first write in 16-bit mode
or after write in 8-bit mode
ns
ns
4-19
4-20
4T + 5
5
5T + 9
13
1. The formulas: T = clock cycle. f ipb = 60MHz, T = 16.7ns.
56858 Technical Data, Rev. 6
36
Freescale Semiconductor
Host Interface Port
HACK
TACKDZ
TACKDV
HD
TACKREQL
TREQACKL
TACKREQH
HREQ
Figure 4-17 Controller-to-Host DMA Read Mode
HA
TRADX
HCS
HDS
HRW
TRADV
TRADZ
HD
Figure 4-18 Single Strobe Read Mode
56858 Technical Data, Rev. 6
Freescale Semiconductor
37
HA
TRADX
HCS
HWR
HRD
HD
TRADZ
TRADV
Figure 4-19 Dual Strobe Read Mode
HACK
HD
TACKDH
TDACKS
TACKREQL
TREQACKL
TACKREQH
HREQ
Figure 4-20 Host-to-Controller DMA Write Mode
56858 Technical Data, Rev. 6
38
Freescale Semiconductor
Host Interface Port
HA
TDSAH
HCS
HDS
TWDS
TDSAH
HRW
HD
TADSS
TADSS
TDSAH
Figure 4-21 Single Strobe Write Mode
HA
HCS
TWDS
HWR
TDSAH
TADSS
HRD
HD
TADSS
Figure 4-22 Dual Strobe Write Mode
56858 Technical Data, Rev. 6
Freescale Semiconductor
39
4.9 Serial Peripheral Interface (SPI) Timing
1
Figure 4-23 SPI Timing
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40° to +120°C, C ≤ 50pF, f = 120MHz
SS
SSIO
SSA
DD
DDIO
DDA A L op
Characteristic
Symbol
Min
Max
Unit
See Figure
Cycle time
Master
Slave
tC
4-24, 4-25,
4-26, 4-27
25
25
—
—
ns
ns
Enable lead time
Master
Slave
tELD
tELG
tCH
tCL
4-27
4-27
—
12.5
—
—
ns
ns
Enable lag time
Master
Slave
—
12.5
—
—
ns
ns
Clock (SCLK) high time
Master
Slave
ns
ns
4-24, 4-25,
4-26, 4-27
9
12.5
—
—
Clock (SCLK) low time
4-27
Master
Slave
12
12.5
—
—
ns
ns
Data set-up time required for inputs
Master
Slave
tDS
4-24, 4-25,
4-26, 4-27
10
2
—
—
ns
ns
Data hold time required for inputs
Master
Slave
tDH
4-24, 4-25,
4-26, 4-27
0
2
—
—
ns
ns
Access time (time to data active from high-impedance state)
Slave
tA
ns
ns
4-27
4-27
5
2
15
9
Disable time (hold time to high-impedance state)
Slave
tD
ns
ns
Data valid for outputs
Master
Slave (after enable edge)
tDV
4-24, 4-25,
4-26, 4-27
—
—
2
14
ns
ns
Data invalid
Master
Slave
tDI
tR
tF
4-24, 4-25,
4-26, 4-27
0
0
—
—
ns
ns
Rise time
Master
Slave
4-24, 4-25,
4-26, 4-27
—
—
11.5
10.0
ns
ns
Fall time
Master
Slave
4-24, 4-25,
4-26, 4-27
—
—
9.7
9.0
ns
ns
1. Parameters listed are guaranteed by design.
56858 Technical Data, Rev. 6
40
Freescale Semiconductor
Serial Peripheral Interface (SPI) Timing
SS
(Input)
SS is held High on master
tC
tR
tF
tCL
SCLK (CPOL = 0)
(Output)
tCH
tF
tR
tCL
SCLK (CPOL = 1)
(Output)
tDH
tCH
tDS
tCH
MSB in
tDI
MISO
(Input)
Bits 14–1
LSB in
tDI(ref)
tDV
MOSI
(Output)
Master MSB out
tF
Bits 14–1
Master LSB out
tR
Figure 4-24 SPI Master Timing (CPHA = 0)
SS
(Input)
SS is held High on master
tC
tF
tR
tCL
SCLK (CPOL = 0)
(Output)
tCH
tF
tCL
SCLK (CPOL = 1)
(Output)
tDS
tCH
tR
tDH
MISO
(Input)
MSB in
tDI
Bits 14–1
LSB in
tDV(ref)
tDV
MOSI
(Output)
Master MSB out
tF
Bits 14– 1
Master LSB out
tR
Figure 4-25 SPI Master Timing (CPHA = 1)
56858 Technical Data, Rev. 6
Freescale Semiconductor
41
SS
(Input)
tC
tF
tELG
tR
tCL
SCLK (CPOL = 0)
(Input)
tCH
tELD
tCL
SCLK (CPOL = 1)
(Input)
tF
tA
tR
tD
tCH
MISO
(Output)
Slave MSB out
tDH
Bits 14–1
tDV
Slave LSB out
tDI
tDS
tDI
MOSI
(Input)
MSB in
Bits 14–1
LSB in
Figure 4-26 SPI Slave Timing (CPHA = 0)
SS
(Input)
tF
tC
tR
tCL
SCLK (CPOL = 0)
(Input)
tCH
tELG
tELD
tCL
SCLK (CPOL = 1)
(Input)
tDV
tR
tF
tA
tCH
tD
Slave LSB out
tDI
MISO
(Output)
Slave MSB out
Bits 14–1
tDV
tDS
tDH
MOSI
(Input)
MSB in
Bits 14–1
LSB in
Figure 4-27 SPI Slave Timing (CPHA = 1)
56858 Technical Data, Rev. 6
42
Freescale Semiconductor
Quad Timer Timing
4.10 Quad Timer Timing
1, 2
Table 4-10 Quad Timer Timing
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40° to +120°C, C ≤ 50pF, f = 120MHz
SS
SSIO
SSA
DD
DDIO
DDA A L op
Characteristic
Symbol
PIN
Min
Max
—
Unit
ns
Timer input period
2T + 3
1T + 3
2T - 3
1T - 3
Timer input high/low period
Timer output period
PINHL
—
ns
POUT
—
ns
Timer output high/low period
POUTHL
—
ns
1. In the formulas listed, T = clock cycle. For fop = 120MHz operation and fipb = 60MHz, T = 8.33ns.
2. Parameters listed are guaranteed by design.
Timer Inputs
PIN
PINHL
PINHL
Timer Outputs
POUT
POUTHL
POUTHL
Figure 4-28 Timer Timing
4.11 Enhanced Synchronous Serial Interface (ESSI) Timing
1
Table 4-11 ESSI Master Mode Switching Characteristics
Operating Conditions: V = V
SS
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40° to +120°C, C ≤ 50pF, f = 120MHz
SSIO
SSA
DD
DDIO
DDA A L op
Parameter
Symbol
Min
Typ
Max
Units
152
—
SCK frequency
fs
—
—
MHz
SCK period3
tSCKW
tSCKH
tSCKL
66.7
—
—
—
ns
ns
ns
33.44
SCK high time
—
—
33.44
—
SCK low time
Output clock rise/fall time
—
4
—
ns
ns
Delay from SCK high to SC2 (bl) high - Master5
tTFSBHM
-1.0
—
1.0
56858 Technical Data, Rev. 6
Freescale Semiconductor
43
1
Table 4-11 ESSI Master Mode Switching Characteristics (Continued)
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40° to +120°C, C ≤ 50pF, f = 120MHz
SS
SSIO
SSA
DD
DDIO
DDA A L op
Parameter
Symbol
Min
Typ
Max
Units
Delay from SCK high to SC2 (wl) high - Master5
Delay from SC0 high to SC1 (bl) high - Master5
Delay from SC0 high to SC1 (wl) high - Master5
Delay from SCK high to SC2 (bl) low - Master5
Delay from SCK high to SC2 (wl) low - Master5
Delay from SC0 high to SC1 (bl) low - Master5
tTFSWHM
-1.0
—
1.0
ns
tRFSBHM
tRFSWHM
tTFSBLM
tTFSWLM
tRFSBLM
tRFSWLM
tTXEM
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-0.1
-0.1
-0.1
-4
—
—
—
—
—
—
—
—
—
—
—
—
1.0
1.0
1.0
1.0
1.0
1.0
2
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Delay from SC0 high to SC1 (wl) low - Master5
SCK high to STD enable from high impedance - Master
SCK high to STD valid - Master
tTXVM
2
SCK high to STD not valid - Master
SCK high to STD high impedance - Master
SRD Setup time before SC0 low - Master
SRD Hold time after SC0 low - Master
tTXNVM
tTXHIM
tSM
—
0
4
—
—
tHM
4
Synchronous Operation (in addition to standard internal clock parameters)
SRD Setup time before SCK low - Master
SRD Hold time after SCK low - Master
tTSM
tTHM
4
4
—
—
—
—
ns
ns
1. Master mode is internally generated clocks and frame syncs
2. Max clock frequency is IP_clk/4 = 60MHz / 4 = 15MHz for an 120MHz part.
3. All the timings for the ESSI are given for a non-inverted serial clock polarity (TSCKP=0 in SCR2 and RSCKP=0 in SCSR)
and a non-inverted frame sync (TFSI=0 in SCR2 and RFSI=0 in SCSR). If the polarity of the clock and/or the frame sync
have been inverted, all the timings remain valid by inverting the clock signal SCK/SC0 and/or the frame sync SC2/SC1 in
the tables and in the figures.
4. 50 percent duty cycle
5. bl = bit length; wl = word length
56858 Technical Data, Rev. 6
44
Freescale Semiconductor
Enhanced Synchronous Serial Interface (ESSI) Timing
tSCKW
tSCKH
tSCKL
SCK output
SC2 (bl) output
SC2 (wl) output
tTFSBHM
tTFSBLM
tTFSWHM
tTFSWLM
tTXVM
tTXEM
tTXNVM
tTXHIM
First Bit
Last Bit
STD
SC0 output
tRFSBHM
tRFBLM
SC1 (bl) output
SC1 (wl) output
tRFSWHM
tRFSWLM
tTSM
tSM
tHM
tTHM
SRD
Figure 4-29 Master Mode Timing Diagram
1
Table 4-12 ESSI Slave Mode Switching Characteristics
Operating Conditions: V = V
SS
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40° to +120°C, C ≤ 50pF, f = 120MHz
SSIO
SSA
DD
DDIO
DDA A L op
Parameter
Symbol
fs
Min
—
Typ
—
—
—
—
4
Max
Units
MHz
ns
152
—
SCK frequency
SCK period3
tSCKW
tSCKH
tSCKL
—
66.7
33.44
SCK high time
—
—
—
ns
33.44
—
SCK low time
ns
Output clock rise/fall time
ns
56858 Technical Data, Rev. 6
Freescale Semiconductor
45
1
Table 4-12 ESSI Slave Mode Switching Characteristics (Continued)
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40° to +120°C, C ≤ 50pF, f = 120MHz
SS
SSIO
SSA
DD
DDIO
DDA A L op
Parameter
Symbol
tTFSBHS
tTFSWHS
tRFSBHS
tRFSWHS
tTFSBLS
tTFSWLS
tRFSBLS
tRFSWLS
tTXES
Min
-1
-1
-1
-1
-29
-29
-29
-29
—
4
Typ
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Max
29
29
29
29
29
29
29
29
15
15
15
15
15
15
—
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Delay from SCK high to SC2 (bl) high - Slave5
Delay from SCK high to SC2 (wl) high - Slave5
Delay from SC0 high to SC1 (bl) high - Slave5
Delay from SC0 high to SC1 (wl) high - Slave5
Delay from SCK high to SC2 (bl) low - Slave5
Delay from SCK high to SC2 (wl) low - Slave5
Delay from SC0 high to SC1 (bl) low - Slave5
Delay from SC0 high to SC1 (wl) low - Slave5
SCK high to STD enable from high impedance - Slave
SCK high to STD valid - Slave
tTXVS
SC2 high to STD enable from high impedance (first bit) - Slave
SC2 high to STD valid (first bit) - Slave
SCK high to STD not valid - Slave
tFTXES
tFTXVS
tTXNVS
tTXHIS
4
4
4
SCK high to STD high impedance - Slave
SRD Setup time before SC0 low - Slave
SRD Hold time after SC0 low - Slave
4
tSS
4
tHS
4
—
Synchronous Operation (in addition to standard external clock parameters)
SRD Setup time before SCK low - Slave
SRD Hold time after SCK low - Slave
tTSS
tTHS
4
4
—
—
—
—
ns
ns
1. Slave mode is externally generated clocks and frame syncs
2. Max clock frequency is IP_clk/4 = 60MHz / 4 = 15MHz for a 120MHz part.
3. All the timings for the ESSI are given for a non-inverted serial clock polarity (TSCKP=0 in SCR2 and RSCKP=0 in SCSR)
and a non-inverted frame sync (TFSI=0 in SCR2 and RFSI=0 in SCSR). If the polarity of the clock and/or the frame sync
have been inverted, all the timings remain valid by inverting the clock signal SCK/SC0 and/or the frame sync SC2/SC1 in
the tables and in the figures.
4. 50 percent duty cycle
5. bl = bit length; wl = word length
56858 Technical Data, Rev. 6
46
Freescale Semiconductor
Enhanced Synchronous Serial Interface (ESSI) Timing
tSCKW
tSCKH
tSCKL
SCK input
SC2 (bl) input
SC2 (wl) input
tTFSBLS
tTFSBHS
tTFSWHS
tTFSWLS
tFTXVS
tFTXES
tTXVS
tTXNVS
tTXES
tTXHIS
First Bit
Last Bit
STD
SC0 input
tRFBLS
tRFSBHS
SC1 (bl) input
SC1 (wl) input
tRFSWHS
tRFSWLS
tTSS
tSS
tHS
tTHS
SRD
Figure 4-30 Slave Mode Clock Timing
56858 Technical Data, Rev. 6
Freescale Semiconductor
47
4.12 Serial Communication Interface (SCI) Timing
4
Table 4-13 SCI Timing
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98V, V
DD
= V
= 3.0–3.6V, T = –40
°
to +120
°
C, C ≤
50pF, f = 120MHz
op
SS
SSIO
SSA
DDIO
DDA
A
L
Characteristic
Symbol
Min
Max
Unit
Baud Rate1
BR
—
(fMAX)/(32)
1.04/BR
Mbps
RXD2 Pulse Width
TXD3 Pulse Width
RXDPW
TXDPW
0.965/BR
0.965/BR
ns
ns
1.04/BR
1. fMAX is the frequency of operation of the system clock in MHz.
2. The RXD pin in SCI0 is named RXD0 and the RXD pin in SCI1 is named RXD1.
3. The TXD pin in SCI0 is named TXD0 and the TXD pin in SCI1 is named TXD1.
4. Parameters listed are guaranteed by design.
RXD
SCI receive
data pin
RXDPW
(Input)
Figure 4-31 RXD Pulse Width
TXD
SCI receive
data pin
TXDPW
(Input)
Figure 4-32 TXD Pulse Width
56858 Technical Data, Rev. 6
48
Freescale Semiconductor
JTAG Timing
4.13 JTAG Timing
1, 3
Table 4-14 JTAG Timing
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40° to +120°C, C ≤ 50pF, f = 120MHz
SS
SSIO
SSA
DD
DDIO
DDA A L op
Characteristic
TCK frequency of operation2
Symbol
fOP
Min
Max
30
—
Unit
MHz
ns
DC
33.3
16.6
3
TCK cycle time
tCY
TCK clock pulse width
TMS, TDI data setup time
TMS, TDI data hold time
TCK low to TDO data valid
TCK low to TDO tri-state
TRST assertion time
DE assertion time
tPW
—
ns
tDS
—
ns
tDH
3
—
ns
tDV
—
12
10
—
ns
tTS
—
ns
tTRST
tDE
35
4T
ns
—
ns
1. Timing is both wait state and frequency dependent. For the values listed, T = clock cycle. For 120MHz operation,
T = 8.33ns.
2. TCK frequency of operation must be less than 1/4 the processor rate.
3. Parameters listed are guaranteed by design.
tCY
tPW
tPW
VIH
VM
VIL
VM
TCK
(Input)
VM = VIL + (VIH – VIL)/2
Figure 4-33 Test Clock Input Timing Diagram
56858 Technical Data, Rev. 6
Freescale Semiconductor
49
TCK
(Input)
tDS
tDH
TDI
TMS
Input Data Valid
(Input)
tDV
TDO
(Output)
Output Data Valid
tTS
TDO
(Output)
Figure 4-34 Test Access Port Timing Diagram
TRST
(Input)
tTRST
Figure 4-35 TRST Timing Diagram
DE
tDE
Figure 4-36 Enhanced OnCE—Debug Event
56858 Technical Data, Rev. 6
50
Freescale Semiconductor
GPIO Timing
4.14 GPIO Timing
1, 2
Table 4-15 GPIO Timing
Operating Conditions: V = V
= V
= 0 V, V = 1.62-1.98V, V
= V
= 3.0–3.6V, T = –40° to +120°C, C ≤ 50pF, f = 120MHz
SS
SSIO
SSA
DD
DDIO
DDA A L op
Characteristic
Symbol
PIN
Min
Max
—
Unit
ns
GPIO input period
2T + 3
1T + 3
2T - 3
1T - 3
GPIO input high/low period
GPIO output period
PINHL
—
ns
POUT
—
ns
GPIO output high/low period
POUTHL
—
ns
1. In the formulas listed, T = clock cycle. For fop = 120MHz operation and fipb = 60MHz, T = 8.33ns
2. Parameters listed are guaranteed by design.
GPIO Inputs
PIN
PINHL
PINHL
GPIO Outputs
POUT
POUTHL
POUTHL
Figure 4-37 GPIO Timing
56858 Technical Data, Rev. 6
Freescale Semiconductor
51
Part 5 Packaging
5.1 Package and Pin-Out Information 56853
This section contains package and pin-out information for the 144-pin LQFP configuration of the 56858.
MISO
MOSI
SCK
Orientation Mark
TXD1
RXD1
PIN 109
PIN 1
V
V
SSIO
SS
DDIO
V
SC12
SC11
SC10
SCK1
SRD1
STD1
D5
D4
DDIO
V
DDIO
V
SSIO
RD
WR
A0
A1
A2
A3
D3
V
D2
DD
V
D1
SS
V
HRWB
HA2
HA1
HA0
SS
MODA
MODB
MODC
V
V
V
V
V
DDIO
SS
DD
DD
SSIO
IRQA
IRQB
V
V
V
CS3
CS2
CS1
CS0
DDA
SSA
SSA
V
SSIO
XTAL
D0
V
EXTAL
A4
DDIO
A20
A19
A18
A17
A5
A6
A7
HD0
HD1
HD2
A16
TXD0
RXD0
PIN 37
PIN 73
V
DD
Figure 5-1 Top View, 56858 144-pin LQFP Package
56858 Technical Data, Rev. 6
52
Freescale Semiconductor
Package and Pin-Out Information 56853
Table 5-1 56858 Pin Identification by Pin Number
Pin
No.
Pin
No.
Pin
No.
Pin
No.
Signal Name
Signal Name
Signal Name
Signal Name
1
MISO
37
CLKO
73
RXD0
109
VDD
2
3
4
5
MOSI
SCK
SS
38
39
40
41
RSTO
RESET
HD3
74
75
76
77
TXD0
A16
110
111
112
113
TIO3
TIO2
TIO1
VDDIO
A17
VDDIO
HD4
A18
6
7
VDDIO
VSSIO
RD
42
43
44
45
46
47
HD5
HD6
78
79
80
81
82
83
A19
A20
114
115
116
117
118
119
TIO0
VSSIO
HDS
8
HD7
VDDIO
D0
9
WR
A0
VDDIO
VSSIO
VSSIO
HCS
10
11
VSSIO
CS0
HREQ
HACK
A1
12
13
14
A2
A3
48
49
50
A8
A9
84
85
86
CS1
CS2
CS3
120
121
122
D6
D7
D8
VDD
A10
15
16
17
18
19
20
21
22
23
VSS
VSS
51
52
53
54
55
56
57
58
59
A11
VDD
VSS
87
88
89
90
91
92
93
94
95
VDD
VDD
VSS
123
124
125
126
127
128
129
130
131
D9
D10
MODA
MODB
MODC
VDDIO
VSSIO
IRQA
IRQB
VDD
VSS
HA0
HA1
HA2
HRWB
D1
VSS
DE
VSS
TRST
TDO
TDI
VSSIO
VDDIO
VSSIO
STD0
TMS
D2
56858 Technical Data, Rev. 6
Freescale Semiconductor
53
Table 5-1 56858 Pin Identification by Pin Number (Continued)
Pin
No.
Pin
No.
Pin
No.
Pin
No.
Signal Name
Signal Name
Signal Name
Signal Name
24
25
26
VDDA
VSSA
VSSA
60
61
62
TCK
VDDIO
VSSIO
96
97
98
D3
D4
D5
132
133
134
SRD0
SCK0
SC00
27
28
29
30
31
XTAL
EXTAL
A4
63
64
65
66
67
A12
A13
99
STD1
SRD1
SCK1
SC10
SC11
135
136
137
138
139
SC01
SC02
D11
100
101
102
103
A14
A5
A15
D12
A6
VDDIO
VDDIO
32
33
34
35
36
A7
68
69
70
71
72
VDDIO
VSSIO
VSSIO
VSS
104
105
106
107
108
SC12
VDDIO
VSSIO
RXD1
TXD1
140
141
142
143
144
VSSIO
VSSIO
D13
HD0
HD1
HD2
VDD
D14
VDD
D15
56858 Technical Data, Rev. 6
54
Freescale Semiconductor
Package and Pin-Out Information 56853
Figure 5-2 144-pin LQFP Mechanical Information
Please see www.freescale.com for the most current case outline.
56858 Technical Data, Rev. 6
Freescale Semiconductor
55
This section contains package and pin-out information for the 144-pin MAPBGA configuration of the 56858.
METALLIZED MARK FOR
PIN 1 IDENTIFICATION
IN THIS AREA
12
10
11
9
2
6
4
5
1
8
7
3
A
V
V
V
V
V
V
V
V
V
V
V
V
DD
DDIO
RXD1
SC12
SSIO
TIO3
TXD1
DD
SS
SS
SSIO
DDIO
SSIO
DDIO
D15
SSIO
MISO
SCK
SSIO
B
C
V
TIO0
TIO1
HREQ
HDS
D7
STD0
SRD0
SC01
SCK0
D12
D13
V
SSIO
DDIO
V
HACK
MOSI
V
DDIO
DDIO
D
V
SC11
SRD1
D4
SC10
D5
TIO2
SCK1
D2
HCS
STD10
D9
D6
D8
SC00
SC02
D14
D11
A0
WR
A1
RD
A2
SS
A3
V
SS
SSIO
E
F
V
V
DD
DD
V
D3
D10
IRQB
MODA
MODB
MODC
V
DD
SS
G
V
HA1
HA0
HA2
HRWB
D1
TDO
A8
A6
EXTAL
IRQA
V
SSIO
SS
H
J
V
CS2
A20
CS3
A19
CS1
A18
CS0
A12
D0
DE
HD7
HD5
A7
A5
XTAL
A4
V
V
DDIO
DDIO
TMS
V
A10
HD3
HD0
DD
SSIO
K
L
V
A17
A16
A15
A14
A13
TDI
A11
HD6
A9
RESET
HD4
RSTO
CLKO
HD1
HD2
V
DDA
SS
V
V
TXD0
RXD0
TCK
TRST
V
V
SSA
SSIO
SS
M
V
V
V
V
V
V
V
V
V
V
V
SSA
SS10
DDIO
DDIO
SSIO
DDIO
SS
DD
SSIO
SSIO
DDIO
DD
Figure 5-3 Bottom-View, 56858 144-pin MAPBGA Package
56858 Technical Data, Rev. 6
56
Freescale Semiconductor
Package and Pin-Out Information 56853
Table 5-2 56858 Pin Identification by Pin Number
Pin No.
E5
Signal Name
Pin No.
F7
Signal Name
D10
Pin No.
D8
Signal Name
HCS
Pin No.
A5
Signal Name
VDDIO
A0
A1
A2
A3
E4
D5
D11
J3
HD0
A3
VDDIO
E3
B4
D12
K2
HD1
C1
VDDIO
E2
C4
D13
L2
HD2
M10
VDDIO
J2
H3
G4
H4
G5
A4
A5
A6
A7
A8
F6
B3
H6
G3
M1
D14
D15
J4
L4
J5
HD3
HD4
HD5
HD6
HD7
D3
K4
RD
RESET
RSTO
RXD0
RXD1
DE
K3
EXTAL
VSSA
K5
H5
L10
B11
L5
J6
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
CLKO
CS0
CS1
L1
G1
L6
VSSA
VSS
C8
B8
G8
G2
F5
HDS
HREQ
HRWB
IRQA
IRQB
MISO
MODA
MODB
MODC
MOSI
VDDA
VDD
D6
B5
SC00
SC01
SC02
SC10
SC11
SC12
SCK0
SCK1
SCK
K6
J8
VSS
E6
D12
A7
VSS
D10
D11
C11
C5
E9
K8
L9
VSS
F1
VSS
B2
F4
K9
K10
K11
J9
M7
K12
A8
VSS
VSS
F3
VSS
F2
C2
C6
E11
D2
B6
D1
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
C3
K1
E1
M6
F12
A9
SRD0
SRD1
SS
J10
J11
L3
J1
M5
M9
L12
G12
VDD
STD0
STD1
TCK
H8
H9
VDD
E8
VDD
L8
56858 Technical Data, Rev. 6
Freescale Semiconductor
57
Table 5-2 56858 Pin Identification by Pin Number (Continued)
Pin No.
H11
H10
H7
Signal Name
Pin No.
B12
A10
A4
Signal Name
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
VSSIO
HA0
Pin No.
M2
Signal Name
VDD
Pin No.
K7
Signal Name
TDI
CS2
CS3
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
J12
E12
A12
B1
VDD
G6
TDO
VDD
B9
TIO0
G7
A1
VDD
C9
TIO1
F9
A2
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
D9
TIO2
F10
F11
E10
D7
M4
H1
B10
J7
TIO3
M12
A6
M3
TMS
M8
L7
TRST
TXD0
TXD1
WR
G10
G11
G9
M11
H12
C12
A11
L11
C10
D4
B7
HA1
E7
HA2
F8
C7
HACK
H2
XTAL
56858 Technical Data, Rev. 6
58
Freescale Semiconductor
Package and Pin-Out Information 56853
D
X
LASER MARK FOR PIN 1
IDENTIFICATION IN
THIS AREA
Y
M
Detail K
NOTES:
E
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND
TOLERANCES PER ASME Y14.5M, 1994.
3. DIMENSION b IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO DATUM PLANE Z.
4. DATUM Z (SEATING PLANE) IS DEFINED BY
THE SPHERICAL CROWNS OF THE SOLDER
BALLS.
5. PARALLELISM MEASUREMENT SHALL
EXCLUDE ANY EFFECT OF MARK ON TOP
SURFACE OF PACKAGE.
0.20
MILLIMETERS
DIM MIN MAX
S
A
A1
A2
b
---
0.27
1.16 REF
0.40
1.60
0.47
11X
e
METALIZED MARK FOR
PIN 1 IDENTIFICATION
IN THIS AREA
9
8
5
4
3
2
1
12 11 10
0.60
D
E
e
S
13.00 BSC
13.00 BSC
1.00 BSC
0.50 BSC
A
B
C
D
E
F
11X
e
5
0.20 Z
G
H
J
A2
A
S
A1
K
L
0.12 Z
4
Z
DETAIL K
M
ROTATED 90 CLOCKWISE
°
3
144X
b
VIEW M-M
0.25
Z X Y
Z
0.10
Figure 5-4 144-pin MAPBGA Mechanical Information
Please see www.freescale.com for the most current case outline.
56858 Technical Data, Rev. 6
Freescale Semiconductor
59
Part 6 Design Considerations
6.1 Thermal Design Considerations
An estimation of the chip junction temperature, T , in °C can be obtained from the equation:
J
Equation 1: TJ = TA + (PD x RθJA
)
Where:
TA = ambient temperature °C
RθJA = package junction-to-ambient thermal resistance °C/W
PD = power dissipation in package
Historically, thermal resistance has been expressed as the sum of a junction-to-case thermal resistance and
a case-to-ambient thermal resistance:
Equation 2: RθJA = RθJC + RθCA
Where:
RθJA = package junction-to-ambient thermal resistance °C/W
RθJC = package junction-to-case thermal resistance °C/W
RθCA = package case-to-ambient thermal resistance °C/W
R
is device-related and cannot be influenced by the user. The user controls the thermal environment to
θJC
change the case-to-ambient thermal resistance, R
. For example, the user can change the air flow around
θCA
the device, add a heat sink, change the mounting arrangement on the Printed Circuit Board (PCB), or
otherwise change the thermal dissipation capability of the area surrounding the device on the PCB. This
model is most useful for ceramic packages with heat sinks; some 90% of the heat flow is dissipated through
the case to the heat sink and out to the ambient environment. For ceramic packages, in situations where
the heat flow is split between a path to the case and an alternate path through the PCB, analysis of the
device thermal performance may need the additional modeling capability of a system level thermal
simulation tool.
The thermal performance of plastic packages is more dependent on the temperature of the PCB to which
the package is mounted. Again, if the estimations obtained from R
the thermal performance is adequate, a system level model may be appropriate.
do not satisfactorily answer whether
θJA
A complicating factor is the existence of three common definitions for determining the junction-to-case
thermal resistance in plastic packages:
•
Measure the thermal resistance from the junction to the outside surface of the package (case) closest to the
chip mounting area when that surface has a proper heat sink. This is done to minimize temperature variation
across the surface.
•
•
Measure the thermal resistance from the junction to where the leads are attached to the case. This definition
is approximately equal to a junction to board thermal resistance.
Use the value obtained by the equation (TJ – TT)/PD where TT is the temperature of the package case
determined by a thermocouple.
56858 Technical Data, Rev. 6
60
Freescale Semiconductor
Electrical Design Considerations
As noted above, the junction-to-case thermal resistances quoted in this data sheet are determined using the
first definition. From a practical standpoint, that value is also suitable for determining the junction
temperature from a case thermocouple reading in forced convection environments. In natural convection,
using the junction-to-case thermal resistance to estimate junction temperature from a thermocouple
reading on the case of the package will estimate a junction temperature slightly hotter than actual. Hence,
the new thermal metric, Thermal Characterization Parameter, or Ψ , has been defined to be (T – T )/P .
JT
J
T
D
This value gives a better estimate of the junction temperature in natural convection when using the surface
temperature of the package. Remember that surface temperature readings of packages are subject to
significant errors caused by inadequate attachment of the sensor to the surface and to errors caused by heat
loss to the sensor. The recommended technique is to attach a 40-gauge thermocouple wire and bead to the
top center of the package with thermally conductive epoxy.
6.2 Electrical Design Considerations
CAUTION
This device contains protective circuitry to guard against
damage due to high static voltage or electrical fields.
However, normal precautions are advised to avoid
application of any voltages higher than maximum rated
voltages to this high-impedance circuit. Reliability of
operation is enhanced if unused inputs are tied to an
appropriate voltage level.
Use the following list of considerations to assure correct operation:
•
Provide a low-impedance path from the board power supply to each VDD pin on the controller, and from the
board ground to each VSS (GND) pin.
•
The minimum bypass requirement is to place six 0.01–0.1 μF capacitors positioned as close as possible to
the package supply pins. The recommended bypass configuration is to place one bypass capacitor on each
of the ten VDD/VSS pairs, including VDDA/VSSA.
•
Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and VSS (GND)
pins are less than 0.5 inch per capacitor lead.
•
•
Use at least a four-layer Printed Circuit Board (PCB) with two inner layers for VDD and GND.
Bypass the VDD and GND layers of the PCB with approximately 100 μF, preferably with a high-grade
capacitor such as a tantalum capacitor.
•
•
Because the device’s output signals have fast rise and fall times, PCB trace lengths should be minimal.
Consider all device loads as well as parasitic capacitance due to PCB traces when calculating capacitance.
This is especially critical in systems with higher capacitive loads that could create higher transient currents
in the VDD and GND circuits.
56858 Technical Data, Rev. 6
Freescale Semiconductor
61
•
•
All inputs must be terminated (i.e., not allowed to float) using CMOS levels.
Take special care to minimize noise levels on the VDDA and VSSA pins.
•
•
When using Wired-OR mode on the SPI or the IRQx pins, the user must provide an external pull-up device.
Designs that utilize the TRST pin for JTAG port or Enhance OnCE module functionality (such as
development or debugging systems) should allow a means to assert TRST whenever RESET is asserted, as
well as a means to assert TRST independently of RESET. Designs that do not require debugging
functionality, such as consumer products, should tie these pins together.
•
The internal POR (Power on Reset) will reset the part at power on with reset asserted or pulled high but
requires that TRST be asserted at power on.
56858 Technical Data, Rev. 6
62
Freescale Semiconductor
Electrical Design Considerations
Part 7 Ordering Information
Table 7-1 lists the pertinent information needed to place an order. Consult a Freescale Semiconductor
sales office or authorized distributor to determine availability and to order parts.
Table 7-1 56858 Ordering Information
Supply
Voltage
Pin
Count
Frequency
(MHz)
Part
Package Type
Order Number
DSP56858
DSP56858
1.8V, 3.3V
1.8V, 3.3V
Low-Profile Quad Flat Pack (LQFP)
MAP Ball Grid Array (MAPBGA)
144
144
120
120
DSP56858FV120
DSP56858VF120
DSP56858
1.8V, 3.3V
Low-Profile Quad Flat Pack (LQFP)
144
120
DSP56858FVE *
*This package is RoHS compliant.
56858 Technical Data, Rev. 6
Freescale Semiconductor
63
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
support@freescale.com
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
support@freescale.com
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
support@freescale.com
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064, Japan
0120 191014 or +81 3 5437 9125
support.japan@freescale.com
Information in this document is provided solely to enable system and
software implementers to use Freescale Semiconductor products. There are
no express or implied copyright licenses granted hereunder to design or
fabricate any integrated circuits or integrated circuits based on the
information in this document.
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
Freescale Semiconductor reserves the right to make changes without further
notice to any products herein. Freescale Semiconductor makes no warranty,
representation or guarantee regarding the suitability of its products for any
particular purpose, nor does Freescale Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or
incidental damages. “Typical” parameters that may be provided in Freescale
Semiconductor data sheets and/or specifications can and do vary in different
applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer
application by customer’s technical experts. Freescale Semiconductor does
not convey any license under its patent rights nor the rights of others.
Freescale Semiconductor products are not designed, intended, or authorized
for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other
application in which the failure of the Freescale Semiconductor product could
create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold Freescale
Semiconductor and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized
use, even if such claim alleges that Freescale Semiconductor was negligent
regarding the design or manufacture of the part.
support.asia@freescale.com
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
LDCForFreescaleSemiconductor@hibbertgroup.com
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor,
Inc. All other product or service names are the property of their respective owners.
This product incorporates SuperFlash® technology licensed from SST.
© Freescale Semiconductor, Inc. 2005. All rights reserved.
DSP56858
Rev. 6
01/2007
相关型号:
©2020 ICPDF网 联系我们和版权申明