780408 [EXTECH]
Heavy Duty Dissolved Oxygen Meter; 重型溶解氧测定仪
| 型号： | 780408 |
| 厂家： | 
EXTECH INSTRUMENTS CORPORATION. |
| 描述： | Heavy Duty Dissolved Oxygen Meter |
| 文件： | 总8页 (文件大小：117K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
User's Manual
Heavy Duty Dissolved Oxygen Meter
Model 407510
Introduction
Congratulations on your purchase of Extech's Heavy Duty Dissolved Oxygen / Temperature
Meter which simultaneously displays Dissolved Oxygen or Oxygen in air, and Temperature.
Units of measure are mg/l for Dissolved Oxygen, % for Oxygen in air, and oC/oF for
temperature. Oxygen is measured with a remote sensor that also contains a thermistor for
measuring temperature. Advanced features include RS 232 PC serial interface, data hold, auto
shut off, and Min/Max/Avg recording.
Meter Description
1. LCD Display
2. POWER ON/OFF key
3. Data HOLD key
4. °C/°F selection key
5. LCD Contrast Adjust
6. RECORD key
7. RECALL key
8. Factor adjust key
9. Probe head
10. Sensor body
11. Sensor plug
12. Sensor jack
13. RS-232 output jack
14. Battery cover (rear)
15. Altitude compensation key
16. O2 Cal key
17. Zero key
18. O2 calibration key
19. % Salt key
2
407510 V7.0 10/06
Getting Started
Note: The dissolved oxygen probe assembly may be shipped to you
from the factory dry. If the probe does not contain electrolyte
solution, refer to the Electrolyte Replacement section of this manual
for the instructions for adding the electrolyte solution prior to initial
use.
Filling the Electrolyte Container Prior to Initial Use
1. Unscrew and remove the electrolyte container from the tip of
the probe.
2. Fill the electrolyte container with new electrolyte.
3. Screw the electrolyte container back onto the electrode
holder and probe handle. Excess Electrolyte may be forced
out through the threads. Wipe clean.
4. Lightly tap the probe to remove any air bubbles.
Calibration
For first time use or after long periods (several days) of non-use, calibrate the instrument using
the following steps. The procedure should be performed in an open, well-ventilated area.
1. Ensure that the sensor is DISCONNECTED from the meter.
2. Turn ON the meter.
3. Slide the O2/DO selector to the O2 position.
4. Press the zero key to null the meter (the display should indicate "OO").
5. Connect the DO sensor to the top of the meter (remove the plastic probe head
protective cap).
6. Allow the meter to stand for at least five minutes until the display stabilizes.
7. Press the O2 Cal key and the display will indicate approx. 20.9 (typical O2 in air).
3
407510 V7.0 10/06
Dissolved Oxygen (DO) Measurements
Measurement Preparation
Before taking measurements, perform the calibration described above if necessary. In addition,
perform the % SALT and ALTITUDE compensation adjustments as described below:
% SALT Compensation
Slide the O2/DO switch to the DO position. If the measured liquid is pure water or is known
not to have a salt content, set the % Salt factor to 0%.
1. Press the % Salt key. The display will indicate 0% on the middle portion of the LCD
display and S on the bottom portion of the LCD.
2. Pressing the Factor Adj. key once will add 1% to the salt factor.
3. Press the Factor Adj. key until the correct factor is displayed.
4. Press the % Salt key to store the factor.
NOTE: 1% = 10 ppt (parts per thousand)
ALTITUDE Compensation
The meter has a default calibration for sea level operation (0 meters). Any significant
deviation from sea level requires a compensation adjustment. Perform the following steps to
do so:
1. Press the ALTITUDE key and the display will indicate a “0” in the middle of the LCD
and an “H” on the lower portion of the LCD.
2. Press the Factor Adj. key once to add 100 meters, twice to add 200 meters, and so on.
Maximum compensation is 3900 meters.
3. Once the desired compensation is displayed, press the ALTITUDE key again to store
the value.
Taking Measurements
1. Immerse the probe in the solution under test. For best automatic temperature
compensation, immerse the probe to a depth of at least 4" (10 cm).
2. Wait until the display stabilizes.
3. The velocity of the liquid coming into contact with the probe must be at least 0.6 to 1
ft/min (0.2 to 0.3 m/s). If the solution is standing, stir the solution with the probe or use
an agitator.
4. Rinse the probe with clean water after each use.
Oxygen in Air (O2) Measurements
Follow the same steps above for DO measurements except for the variations described below:
1. Slide the O2/DO switch to the O2 position.
2. The display will indicate the oxygen air value in %.
Temperature Measurements
The lower display will indicate the temperature of the measured solution. Press the oC/oF key to
change the temperature units.
4
407510 V7.0 10/06
Advanced Features
Data Hold
Press the Data Hold key to freeze the displayed value. The LCD will display DH for Data Hold
mode along with the held reading. Press the Hold key again to release the data hold function.
MIN/MAX/AVG Data Recording
When selected, the Data Recording function records the Min, Max, and Average readings. To
start a data recording session:
1. Press the RECORD key once. The REC indicator will appear on the display and the meter
will begin to record the lowest (min), highest (max), and average (avg) readings.
2. To recall the data, press the RECALL key once. The MAX indicator will appear along with
the highest reading recorded since the RECORD key was pressed.
3. Press the RECALL key again to view the MIN value.
4. Press the RECALL key again to view the AVG reading.
5. To exit the Record mode, press the RECORD key again. The display indicators REC,
MIN, MAX, and AVG will disappear.
Auto Power OFF
The meter includes an Auto shut off feature that preserves battery life. The meter will
automatically turn off if no function button is pressed in any 10 minute period. To disable this
feature press the RECORD key to engage the record function.
LCD Contrast Adjust
It may be necessary to adjust the display contrast due to a change in viewing angle or voltage
drift. Use the LCD Contrast adjustment located on the right side of the meter to set the
preferred contrast.
CPU Reset
Certain improper keystroke sequences can cause the meter to “hang” and become inoperable.
The following procedure will reset the meter.
1. Slide the O2/DO switch to the O2 position.
2. Turn the meter OFF and disconnect the DO probe.
3. Press and HOLD the O2 CAL key and then press the POWER key.
4. Release the O2 CAL key and then press the ZERO key.
5. Connect the DO probe.
6. Wait several minutes for the reading to stabilize and then press the O2 CAL key.
RS-232 PC Interface
The meter includes a RS-232 serial data port. This interface was designed to operate with the
Extech Data Acquisition Software/Hardware kit Part No. 407001. This kit enables the user to
capture, store and display readings using a PC.
5
407510 V7.0 10/06
Probe Head Replacement
The probe head on the tip of the probe holds a thin Teflon® membrane and an electrolyte
container. Calibration or reading errors could indicate loss of electrolyte or a dirty/damaged
membrane. The membrane is very delicate and can easily be damaged if it comes in contact
with solid objects. Replacement probe heads are available from your local distributor.
Replacement procedure
1. Unscrew the probe head and electrolyte container from the probe handle and discard.
2. Fill the new probe head/electrolyte container with electrolyte.
3. Screw the probe head onto the probe handle. Excess electrolyte may be forced out
through the threads. Wipe clean.
4. Lightly tap the probe to remove any air bubbles.
1. Probe handle
2. Temperature sensor
3. Probe Head
6
407510 V7.0 10/06
Battery Replacement
The low battery indication LBT appears on the LCD when the battery runs low.
To replace the battery:
1. Remove the meter's rubber protective cover to access the rear battery compartment.
2. Remove the battery compartment cover using a small coin or screwdriver and remove the
9V battery.
3. Replace the 9V battery and reinstall the cover and holster.
Specifications
General Specifications
Circuit
Custom one-chip LSI microprocessor circuit
Display
Dual function 0.5" (13 mm) 1999 count LCD w/ contrast adjust
Measurements
Dissolved O2: mg/l (milligrams per liter); Oxygen in air: %;
Temperature: °C/°F
Data hold
Data hold key freezes displayed reading
Remote Polarographic Dissolved Oxygen Sensor
Temperature sensor: Precision thermistor
Min/Max/Avg readings stored for later recall
Meter turns off after 10 minutes
Sensor Structure
Data recording
Auto power off
Sample rate
0.4 Sec (approx.)
Data Output
RS 232 PC serial interface
Operating conditions Temperature: 32 to 122 °F (0 to 50 °C); Humidity: < 80% RH
Battery power 9V alkaline battery
Power Consumption Approx. 6.6 mA DC
Weight
0.74 lbs. / 335 g (including batteries & probe)
Dimensions
Main instrument: 7.1 x 2.8 x1.3" (180 x 72 x 32mm)
Probe: 4.9" x 0.8" length/diameter (125 x 20mm)
Carrying case, 9V battery, and 5 membranes
Accessories
Optional
Membranes, data acquisition software & RS232 interface cable
accessories
Electrical Specifications
Measurement
Range
0.0 - 19.9 mg/L
0 - 100% O2
32 to 122 oF
0 to 50 oC
Resolution
0.1mg/L
0.1 % O2
0.1oF/C
Accuracy
+ 0.4 mg/L
+ 0.7% O2
±1.5 oF
Dissolved Oxygen
Oxygen in air
Temperature
(probe only)
+ 0.8 oC
Compensation
adjustments
Temperature (automatic)
Salt
32 to 122 oF (0 to 50oC)
0 to 39% (1% = ppt)
0 to 3900 meters
Altitude
7
407510 V7.0 10/06
Calibration and Repair Services
Extech offers repair and calibration services for the products we sell. Extech also provides
NIST certification for most products. Call the Customer Service Department for information on
calibration services available for this product. Extech recommends that annual calibrations be
performed to verify meter performance and accuracy.
Warranty
EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in
parts and workmanship for three years from date of shipment (a six month limited warranty
applies to sensors and cables). If it should become necessary to return the instrument for
service during or beyond the warranty period, contact the Customer Service Department at
(781) 890-7440 ext. 210 for authorization or visit our website www.extech.com for contact
information. A Return Authorization (RA) number must be issued before any product is
returned to Extech. The sender is responsible for shipping charges, freight, insurance and
proper packaging to prevent damage in transit. This warranty does not apply to defects
resulting from action of the user such as misuse, improper wiring, operation outside of
specification, improper maintenance or repair, or unauthorized modification. Extech specifically
disclaims any implied warranties or merchantability or fitness for a specific purpose and will not
be liable for any direct, indirect, incidental or consequential damages. Extech's total liability is
limited to repair or replacement of the product. The warranty set forth above is inclusive and no
other warranty, whether written or oral, is expressed or implied.
ꢀ
Support line (781) 890-7440
Technical support: Extension 200; E-mail: support@extech.com
Repair & Returns: Extension 210; E-mail: repair@extech.com
Product specifications subject to change without notice
For the latest version of this User’s Guide, Software updates, and other
up-to-the-minute product information, visit our website: www.extech.com
Extech Instruments Corporation, 285 Bear Hill Rd., Waltham, MA 02451
Copyright © 2006 Extech Instruments Corporation. All rights reserved including the right
of reproduction in whole or in part in any form.
8
407510 V7.0 10/06
相关型号：
78041-0002
6.35mm (.250") Pitch, EXTreme PowerPlus™ Header, All Power, Through Hole, Vertical, 3 Circuits, with Peg, Lead-free
MOLEX
78045-0660
Board Connector, 6 Contact(s), 2 Row(s), Female, 0.079 inch Pitch, Crimp Terminal, Locking, Black Insulator, Plug
MOLEX
78045-1060
2.00mm (.079) Pitch, Milli-Grid™ Crimp Housing, 10 Circuits, with Center Polarization Key and side Locking Ramps, Leadfree
MOLEX
78045-1260
Board Connector, 12 Contact(s), 2 Row(s), Female, 0.079 inch Pitch, Crimp Terminal, Locking, Black Insulator, Plug
MOLEX
©2020 ICPDF网 联系我们和版权申明