HM62V16256CSERIES [ETC]
;HM62V16256C Series
4 M SRAM (256-kword × 16-bit)
ADE-203-1099G (Z)
Rev. 4.0
Jul. 31, 2002
Description
The Hitachi HM62V16256C Series is 4-Mbit static RAM organized 262,144-word × 16-bit. HM62V16256C
Series has realized higher density, higher performance and low power consumption by employing CMOS
process technology (6-transistor memory cell). It offers low power standby power dissipation; therefore, it is
suitable for battery backup systems. It is packaged in standard 44-pin plastic TSOPII.
Features
•
•
•
Single 2.5 V and 3.0 V supply: 2.2 V to 3.6 V
Fast access time: 55 ns (max)
Power dissipation:
Active: 5.0 mW/MHz (typ)(VCC = 2.5 V)
: 6.0 mW/MHz (typ) (VCC = 3.0 V)
Standby: 2 µW (typ) (VCC = 2.5 V)
: 2.4 µW (typ) (VCC = 3.0 V)
Completely static memory.
•
No clock or timing strobe required
Equal access and cycle times
Common data input and output.
Three state output
•
•
•
Battery backup operation.
2 chip selection for battery backup
HM62V16256C Series
Ordering Information
Type No.
Access time
55 ns
Package
HM62V16256CLTT-5
400-mil 44-pin plastic TSOPII (normal-bend type) (TTP-44DB)
HM62V16256CLTT-5SL 55 ns
2
HM62V16256C Series
Pin Arrangement
44-pin TSOP
44
1
A5
A4
A3
2
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
A6
3
A7
A2
4
OE
UB
LB
A1
5
A0
6
CS1
I/O0
I/O1
I/O2
I/O3
VCC
VSS
I/O4
I/O5
I/O6
I/O7
WE
A17
A16
A15
A14
A13
7
I/O15
I/O14
I/O13
I/O12
VSS
VCC
I/O11
I/O10
I/O9
I/O8
CS2
A8
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
A9
A10
A11
A12
(Top view)
Pin Description
Pin name
A0 to A17
I/O0 to I/O15
CS1
Function
Address input
Data input/output
Chip select 1
Chip select 2
Write enable
CS2
WE
OE
Output enable
Lower byte select
Upper byte select
Power supply
Ground
LB
UB
VCC
VSS
3
HM62V16256C Series
Block Diagram
LSB
A12
V CC
V SS
A11
A10
A9
•
•
•
•
•
A8
Memory matrix
2,048 x 2,048
Row
decoder
A13
A14
A15
A16
A17
MSB
A7
I/O0
•
•
•
•
Column I/O
Input
data
Column decoder
control
I/O15
LSB
MSB
A4 A3 A2 A1 A5 A6 A0
•
•
CS2
CS1
LB
Control logic
UB
WE
OE
4
HM62V16256C Series
Operation Table
CS1 CS2 WE
OE
×
UB
×
LB
×
I/O0 to I/O7
High-Z
High-Z
High-Z
Dout
I/O8 to I/O15
Operation
Standby
H
×
×
High-Z
High-Z
High-Z
Dout
×
L
×
×
×
×
Standby
×
L
L
L
L
L
L
L
×
×
×
H
L
H
L
Standby
H
H
H
H
H
H
H
H
H
H
L
L
Read
L
H
L
L
Dout
High-Z
Dout
Lower byte read
Upper byte read
Write
L
H
L
High-Z
Din
×
L
Din
L
×
H
L
L
Din
High-Z
Din
Lower byte write
Upper byte write
Output disable
L
×
H
×
High-Z
High-Z
H
H
×
High-Z
Note: H: VIH, L: VIL, ×: VIH or VIL
Absolute Maximum Ratings
Parameter
Symbol
VCC
Value
–0.5 to + 4.6
Unit
Power supply voltage relative to VSS
V
Terminal voltage on any pin relative to VSS
Power dissipation
VT
–0.5*1 to VCC + 0.3*2
V
PT
1.0
W
°C
°C
Storage temperature range
Tstg
Tbias
–55 to +125
–20 to +85
Storage temperature range under bias
Notes: 1. VT min: –3.0 V for pulse half-width ≤ 30 ns.
2. Maximum voltage is +4.6 V.
DC Operating Conditions
Parameter
Symbol Min
Typ
Max
3.6
Unit
Note
Supply voltage
VCC
VSS
2.2
0
2.5/3.0
0
V
0
V
Input high voltage VCC = 2.2 V to 2.7 V VIH
VCC = 2.7 V to 3.6 V VIH
2.0
2.0
–0.2
–0.3
–20
—
VCC + 0.3
VCC + 0.3
0.4
V
—
V
Input low voltage
VCC = 2.2 V to 2.7 V VIL
VCC = 2.7 V to 3.6 V VIL
—
V
1
1
—
0.6
V
Ambient temperature range
Ta
—
70
°C
Note: 1. VIL min: –3.0 V for pulse half-width ≤ 30 ns.
5
HM62V16256C Series
DC Characteristics
Parameter
Symbol Min
Typ*1 Max
Unit Test conditions
Input leakage current
Output leakage current
|ILI|
—
—
—
—
1
1
µA
µA
Vin = VSS to VCC
|ILO|
CS1 = VIH or CS2 = VIL or
OE = VIH or WE = VIL or
LB = UB = VIH, VI/O = VSS to VCC
Operating current
ICC
—
—
5
8
20
25
mA
mA
CS1 = VIL, CS2 = VIH,
Others = VIH/VIL, II/O = 0 mA
Average operating current
ICC1
Min. cycle, duty = 100%,
II/O = 0 mA, CS1 = VIL, CS2 = VIH,
Others = VIH/VIL
ICC2
—
2
5
mA
Cycle time = 1 µs, duty = 100%,
II/O = 0 mA, CS1 ≤ 0.2 V,
CS2 ≥ VCC – 0.2 V
VIH ≥ VCC – 0.2 V, VIL ≤ 0.2 V
Standby current
Standby current
ISB
—
—
0.1
0.5
0.3
20
mA
µA
CS2 = VIL
2
ISB1
*
0 V ≤ Vin
(1) 0 V ≤ CS2 ≤ 0.2 V or
(2) CS1 ≥ VCC – 0.2 V,
CS2 ≥ VCC – 0.2 V or
(3) LB = UB ≥ VCC – 0.2 V
CS2 ≥ VCC – 0.2 V
CS1 ≤ 0.2 V
3
ISB1*
—
0.5
—
10
—
µA
V
Output high VCC =2.2 V to 2.7 V VOH
voltage
2.0
IOH = –0.5 mA
VCC =2.7 V to 3.6 V VOH
VCC =2.2 V to 3.6 V VOH
2.4
—
—
V
V
V
IOH = –1 mA
IOH = –100 µA
IOL = 0.5 mA
VCC – 0.2—
—
Output low
voltage
VCC =2.2 V to 2.7 V VOL
—
—
0.4
VCC =2.7 V to 3.6 V VOL
VCC =2.2 V to 3.6 V VOL
—
—
—
—
0.4
0.2
V
V
IOL = 2 mA
IOL = 100 µA
Notes: 1. Typical values are at VCC = 2.5 V/3.0 V, Ta = +25°C and not guaranteed.
2. This characteristic is guaranteed only for L-version.
3. This characteristic is guaranteed only for L-SL version.
6
HM62V16256C Series
Capacitance (Ta = +25°C, f = 1.0 MHz)
Parameter
Symbol
Min
—
Typ
—
Max
8
Unit
pF
Test conditions Note
Input capacitance
Input/output capacitance
Cin
Vin = 0 V
VI/O = 0 V
1
1
C
—
—
10
pF
I/O
Note: 1. This parameter is sampled and not 100% tested.
7
HM62V16256C Series
AC Characteristics (Ta = –20 to +70°C, VCC = 2.2 V to 3.6 V, unless otherwise noted.)
Test Conditions
•
Input pulse levels: VIL = 0.4 V, VIH = 2.0 V (VCC = 2.2 V to 2.7 V)
VIL = 0.4 V, VIH = 2.2 V (VCC = 2.7 V to 3.6 V)
•
•
•
•
•
•
Input rise and fall time: 5 ns
Input timing reference levels: 1.1 V (VCC = 2.2 V to 2.7 V)
Output timing reference levels: 1.1 V (VCC = 2.2 V to 2.7 V)
Input timing reference levels: 1.4 V (VCC = 2.7 V to 3.6 V)
Output timing reference levels: 1.4 V (VCC = 2.7 V to 3.6 V)
Output load: See figures (Including scope and jig)
VTM
1.4 V
R1
RL=500 Ω
Dout
Dout
R1 = 3070 Ω
30pF
R2
R2 = 3150 Ω
50pF
VTM = 2.3 V
Output load (A)
(VCC = 2.2 V to 2.7 V)
Output load (B)
(VCC = 2.7 V to 3.6 V)
8
HM62V16256C Series
Read Cycle
HM62V16256C
-5
Parameter
Symbol
tRC
Min
55
—
—
—
—
10
—
10
10
5
Max
—
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes
Read cycle time
Address access time
Chip select access time
tAA
55
55
55
35
—
tACS1
tACS2
tOE
Output enable to output valid
Output hold from address change
LB, UB access time
tOH
tBA
55
—
Chip select to output in low-Z
tCLZ1
tCLZ2
tBLZ
2, 3
—
2, 3
LB, UB enable to low-z
—
2, 3
Output enable to output in low-Z
Chip deselect to output in high-Z
tOLZ
5
—
2, 3
tCHZ1
tCHZ2
tBHZ
0
20
20
20
20
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
0
LB, UB disable to high-Z
0
Output disable to output in high-Z
tOHZ
0
9
HM62V16256C Series
Write Cycle
HM62V16256C
-5
Parameter
Symbol
tWC
Min
55
50
50
40
50
0
Max
—
—
—
—
—
—
—
—
—
—
20
20
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes
Write cycle time
Address valid to end of write
Chip selection to end of write
Write pulse width
tAW
tCW
5
4
tWP
LB, UB valid to end of write
Address setup time
tBW
tAS
6
7
Write recovery time
tWR
0
Data to write time overlap
Data hold from write time
Output active from end of write
Output disable to output in High-Z
Write to output in high-Z
tDW
25
0
tDH
tOW
5
2
tOHZ
tWHZ
0
1, 2
1, 2
0
Notes: 1. tCHZ, tOHZ, tWHZ and tBHZ are defined as the time at which the outputs achieve the open circuit conditions
and are not referred to output voltage levels.
2. This parameter is sampled and not 100% tested.
3. At any given temperature and voltage condition, tHZ max is less than tLZ min both for a given device
and from device to device.
4. A write occures during the overlap of a low CS1, a high CS2, a low WE and a low LB ora low UB. A
write begins at the latest transition among CS1 going low, CS2 going high, WE going low and LB
going low or UB going low. A write ends at the earliest transition among CS1 going high, CS2going
low, WE going high and LB going high or UB going high. tWP is measured fromthe beginning of write
to the end of write.
5. tCW is measured from the later of CS1 going low or CS2 going high to the end of write.
6. tAS is measured from the address valid to the beginning of write.
7. tWR is measured from the earliest of CS1 or WE going high or CS2 going low to the end of writecycle.
10
HM62V16256C Series
Timing Waveform
Read Cycle
tRC
Address
Valid address
tAA
tACS1
CS1
2, 3
2, 3
1, 2, 3
tCLZ1
*
tCHZ1
*
CS2
tACS2
tCLZ2
1, 2, 3
*
tCHZ2
*
1, 2, 3
tBHZ
*
tBA
LB, UB
2, 3
tBLZ
*
1, 2, 3
tOHZ
*
tOE
OE
2, 3
tOLZ
*
tOH
High impedance
Dout
Valid data
11
HM62V16256C Series
Write Cycle (1) (WE Clock)
tWC
Valid address
Address
7
tWR
*
5
5
tCW
*
CS1
tCW
*
CS2
tBW
LB, UB
tAW
4
tWP
*
6
WE
tAS*
tDW
Valid data
tDH
Din
1, 2
tWHZ
*
2
tOW
*
High impedance
Dout
12
HM62V16256C Series
Write Cycle (2) (CS Clock, OE = VIH)
tWC
Valid address
tAW
Address
6
7
5
5
tAS
*
tWR*
tCW
*
CS1
tCW
*
CS2
tBW
LB, UB
4
tWP
*
WE
tDW
Valid data
tDH
Din
High impedance
Dout
13
HM62V16256C Series
Write Cycle (3) (LB, UB Clock, OE = VIH)
tWC
Valid address
tAW
Address
5
5
7
tCW
*
tWR
*
CS1
tCW
*
CS2
6
tBW
tAS
*
LB, UB
4
tWP
*
WE
tDW
Valid data
tDH
Din
High impedance
Dout
14
HM62V16256C Series
Low VCC Data Retention Characteristics (Ta = –20 to +70°C)
Parameter
Symbol
Min
Typ*4
Max
Unit
Test conditions*3
VCC for data retention
VDR
2.0
—
3.6
V
Vin ≥ 0V
(1) 0 V ≤ CS2 ≤ 0.2 V or
(2) CS2 ≥ VCC – 0.2 V
CS1 ≥ VCC – 0.2 V or
(3) LB = UB ≥ VCC – 0.2 V,
CS2 ≥ VCC – 0.2 V,
CS1 ≤ 0.2 V
1
Data retention current
ICCDR
*
—
0.5
20
µA
VCC = 3.0 V, Vin ≥ 0V
(1) 0 V ≤ CS2 ≤ 0.2 V or
(2) CS2 ≥ VCC – 0.2 V,
CS1 ≥ VCC – 0.2 V or
(3) LB = UB ≥ VCC – 0.2 V,
CS2 ≥ VCC – 0.2 V,
CS1 ≤ 0.2 V
2
ICCDR
*
—
0
0.5
—
10
—
µA
ns
Chip deselect to data
retention time
tCDR
See retention waveform
Operation recovery time
tR
tRC*5
—
—
ns
Notes: 1. This characteristic is guaranteed only for L-version, 10 µA max. at Ta = –20 to +40°C.
2. This characteristic is guaranteed only for L-SL version, 3 µA max. at Ta = –20 to +40°C.
3. CS2 controls address buffer, WE buffer, CS1 buffer, OE buffer, LB, UB buffer and Din buffer. If CS2
controls data retention mode, Vin levels (address, WE, OE, CS1, LB, UB, I/O) can be in the high
impedance state. If CS1 controls data retention mode, CS2 mustbe CS2 ≥ VCC – 0.2V or0 V ≤ CS2
≤ 0.2 V. The other input levels (address, WE, OE, LB, UB, I/O) can be in the high impedance state.
4. Typical values are at VCC = 3.0 V, Ta = +25˚C and not guaranteed.
5. tRC = read cycle time.
15
HM62V16256C Series
Low VCC Data Retention Timing Waveform (1) (CS1 Controlled)
Data retention mode
tCDR
tR
VCC
2.2 V
VDR
2.0 V
CS1
0 V
≥
CS1 VCC – 0.2 V
Low VCC Data Retention Timing Waveform (2) (CS2 Controlled)
tCDR
Data retention mode
tR
VCC
2.2 V
CS2
VDR
0.4 V
0 V
<
<
0 V CS2 0.2 V
Low VCC Data Retention Timing Waveform (3) (LB, UB Controlled)
Data retention mode
tCDR
tR
VCC
2.2 V
VDR
2.0 V
LB, UB
0 V
≥
LB, UB VCC – 0.2 V
16
HM62V16256C Series
Package Dimensions
HM62V16256CLTT Series (TTP-44DB)
As of January, 2002
Unit: mm
18.41
18.81 Max
44
23
22
1
0.80
0.13
0.80
*0.30 ± 0.10
0.25 ± 0.05
M
11.76 ± 0.20
1.005 Max
0˚ – 5˚
0.50 ± 0.10
0.10
Hitachi Code
TTP-44DB
JEDEC
JEITA
Mass (reference value)
—
—
0.43 g
*Dimension including the plating thickness
Base material dimension
17
HM62V16256C Series
Cautions
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright,
trademark, or other intellectual property rights for information contained in this document. Hitachi bears no
responsibility for problems that may arise with third party’s rights, including intellectual property rights, in
connection with use of the information contained in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However, contact
Hitachi’s sales office before using the product in an application that demands especially high quality and
reliability or where its failure or malfunction may directly threaten human life or cause riskof bodilyinjury,
such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safetyequipment
or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for
maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and
other characteristics. Hitachi bears no responsibility forfailure or damage whenused beyond the guaranteed
ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in
semiconductor devices and employ systemic measures such as fail-safes, so that the equipment
incorporating Hitachi product does not cause bodily injury, fire or other consequential damage due to
operation of the Hitachi product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Hitachi.
7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductorproducts.
Hitachi, Ltd.
Semiconductor & Integrated Circuits
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Tel: (03) 3270-2111 Fax: (03) 3270-5109
URL
http://www.hitachisemiconductor.com/
For further information write to:
Hitachi Semiconductor
(America) Inc.
179 East Tasman Drive Whitebrook Park
Hitachi Europe Ltd.
Electronic Components Group
Hitachi Asia Ltd.
Hitachi Tower
16 Collyer Quay #20-00
Singapore 049318
Hitachi Asia (Hong Kong) Ltd.
Group III (Electronic Components)
7/F., North Tower
San Jose,CA 95134
Lower Cookham Road
World Finance Centre,
Tel: <1> (408) 433-1990 Maidenhead
Fax: <1>(408) 433-0223 Berkshire SL6 8YA, United Kingdom
Tel: <44> (1628) 585000
Tel : <65>-6538-6533/6538-8577
Fax : <65>-6538-6933/6538-3877
URL : http://semiconductor.hitachi.com.sg
Harbour City, Canton Road
Tsim Sha Tsui, Kowloon Hong Kong
Tel : <852>-2735-9218
Fax : <852>-2730-0281
URL : http://semiconductor.hitachi.com.hk
Fax: <44> (1628) 585200
Hitachi Asia Ltd.
(Taipei Branch Office)
4/F, No. 167, Tun Hwa North Road
Hung-Kuo Building
Hitachi Europe GmbH
Electronic Components Group
Dornacher Strasse 3
D-85622 Feldkirchen
Postfach 201,D-85619 Feldkirchen
Germany
Tel: <49> (89) 9 9180-0
Fax: <49> (89) 9 29 30 00
Taipei (105), Taiwan
Tel : <886>-(2)-2718-3666
Fax : <886>-(2)-2718-8180
Telex : 23222 HAS-TP
URL : http://www.hitachi.com.tw
Copyright
C
Hitachi, Ltd., 2002. All rights reserved. Printed in Japan.
Colophon 6.0
18
相关型号:
![](http://pdffile.icpdf.com/pdf2/p00235/img/page/HM62V16258CL_1377718_files/HM62V16258CL_1377718_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00235/img/page/HM62V16258CL_1377718_files/HM62V16258CL_1377718_2.jpg)
HM62V16258CLTT-5SL
Standard SRAM, 256KX16, 55ns, CMOS, PDSO44, 0.400 INCH, PLASTIC, TSOP2-44
HITACHI
©2020 ICPDF网 联系我们和版权申明